Requesting all the GPIOs on a single array (mx28evk_gpios[]) can make the
error handling of gpio_requests much simpler.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The mxs_get_ocotp() function already prints an error message in the case of
a timeout, so no need to print them again in the board files.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Like with all other clocks, the divider for the SAIF devices should not
be altered when the clock is gated. Bail out when this is the case like
the other clocks do.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Dong Aisheng-B29396 <B29396@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Both imx23 and imx28 have CHIPID register at address 0x8001c310, which
can be used to identify the SoC. This patch changes cpu_is_xxx and
__arch_decomp_setup to use this CHIPID register than machine type to
detect the chip between imx23 and imx28, so that we do not need to
change these functions whenever a new board/machine gets added.
Suggested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
i.MX28 has four SSP/MMC units, only two of which are currently
usable.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Convert MXS to use the new amba_device_alloc APIs.
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When this is the only content remaining in mach/system.h then the
whole file is removed.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-and-tested-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: David Brown <davidb@codeaurora.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Now that all implementations of arch_idle() are equivalent to cpu_do_idle()
we can just use the later directly and stop including mach/system.h.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-and-tested-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Another simple series related to clock management, this time only for
imx.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIVAwUATwta7GCrR//JCVInAQJD6A//ZbZtOEctF1nfrpQ6LeoPdJFWUt/4d+GX
JW2CksR94AB1BqTNV0N0a/pRUNTEo5bBVzeXJw8XnJSCNnIakJpFoeZBh93YTOsO
ZfuxhYwkVrbCusELaltrSdj5lUW/KgE58vTpfCkkqGgyMQQTzH73zJyjNOYAaWAK
FleQ5jCpxm3FqoA5jp9+7xcHwF+o2btKXzM4kyEO/cAaypEIOz83qAK16FKzIvuI
ba9QgMXN5sAKwNMIkNYJruHknlshGT00NBlYJebT0MXbd7pyuN9VsIfMMEQ+VG8B
3hvfVvHrVeHiWoqdF0r8uxr/SZJiCZlE5RhDK1pO1MXPsroaOEAMSAeA/Y2193HK
Dkz37iBBUf5T4mA5GfKb7dH4maM79OQ+SEtcQySF18hT+qCHeJV3J8WC0c7C81Ej
7RFBJjFfpwKwd/SXFKn/PYmlgJZ4aW1+FNyx5xnIjBNpnU8N9knw2h1qGVvcjp+V
SRQ7zghQToDY425U0ziiFle3XsrC/a0QZrzbFo+rqgUXMZQ2Vq7CiZr/E8QNsbiE
I0AVE6hlWEx3aXgDoHKb0K3kSthIT7QkmO2UjhJmplEIjgVZw+vfjmAM9O+AeWJC
BYLzgl2CRAZekNBD77aUdB1VUVz2cUUQ2zgh0wH11k2ca2+h3Lyw4buzsV4u3nxj
Fqinw2GEt2U=
=czKE
-----END PGP SIGNATURE-----
Merge tag 'clk' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
clock management changes for i.MX
Another simple series related to clock management, this time only for
imx.
* tag 'clk' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: mxs: select HAVE_CLK_PREPARE for clock
clk: add config option HAVE_CLK_PREPARE into Kconfig
ASoC: mxs-saif: convert to clk_prepare/clk_unprepare
video: mxsfb: convert to clk_prepare/clk_unprepare
serial: mxs-auart: convert to clk_prepare/clk_unprepare
net: flexcan: convert to clk_prepare/clk_unprepare
mtd: gpmi-lib: convert to clk_prepare/clk_unprepare
mmc: mxs-mmc: convert to clk_prepare/clk_unprepare
dma: mxs-dma: convert to clk_prepare/clk_unprepare
net: fec: add clk_prepare/clk_unprepare
ARM: mxs: convert platform code to clk_prepare/clk_unprepare
clk: add helper functions clk_prepare_enable and clk_disable_unprepare
Fix up trivial conflicts in drivers/net/ethernet/freescale/fec.c due to
commit 0ebafefcaa ("net: fec: add clk_prepare/clk_unprepare") clashing
trivially with commit e163cc97f9 ("net/fec: fix the .remove code").
Conflicts:
arch/arm/mach-mxs/include/mach/common.h
Pull in previous samsung conflict merges and do a trivial
merge of an mxs double-add conflict.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Remove the now empty arch_reset() from all the mach/system.h includes,
and remove its callsite. Remove arm_machine_restart() as this function
no longer does anything useful.
For samsung platforms, remove the include of mach/system-reset.h and
plat/system-reset.h from their respective mach/system.h headers as these
just define their arch_reset functions. As a result, the s3c2410 and
plat-samsung system-reset.h files are no longer referenced, so remove
these files entirely.
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Hook these platforms restart code into the new restart hook rather
than using arch_reset().
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds clk_prepare/clk_unprepare for mxs clock api by
renaming the existing non-atomic clk_enable/clk_disable to
clk_prepare/clk_unprepare and adding a pair of dummy
clk_enable/clk_disable. Then with selecting HAVE_CLK_PREPARE for
mxs clock, we can fix the mutex locking warning that has been
reported for a few times.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The patch converts mxs platform code to clk_prepare/clk_unprepare
by using helper functions clk_prepare_enable/clk_disable_unprepare.
Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This is for supporting saif record function.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@ti.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
It's a correction of two macro names, renaming them from IRADC to LRADC.
Signed-off-by: Peter Rusko <rusko.peter@prolan.hu>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Adding the machine_is_* line was forgotten when converting mach-stmp378x to
mach-mxs.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: stable@kernel.org
Initializers of m28evk and stmp378x_devb fixed to be in order
they are called.
reference: http://article.gmane.org/gmane.linux.ports.arm.omap/50721
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Lauri Hintsala <lauri.hintsala@bluegiga.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
reg | (1 << clk->enable_shift) always evaluates to true. Switch it
to & which makes much more sense. Same fix as 13be9f00 (ARM i.MX28: fix
bit operation) at a different location.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: stable@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Conflicts:
arch/arm/mach-omap2/board-4430sdp.c
arch/arm/mach-omap2/board-omap4panda.c
arch/arm/mach-omap2/include/mach/omap4-common.h
arch/arm/plat-omap/include/plat/irqs.h
The changes to omap4-common.h were moved to arch/arm/mach-omap2/common.h
and the other trivial conflicts resolved. The now empty ifdef in irqs.h
was also eliminated.
We only need to set the system up for a soft-restart if we're going to
be doing a soft-restart. Provide a new function (soft_restart()) which
does the setup and final call for this, and make platforms use it.
Eliminate the call to setup_restart() from the default handler.
This means that platforms arch_reset() function is no longer called with
the page tables prepared for a soft-restart, and caches will still be
enabled.
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Krzysztof Ha■asa <khc@pm.waw.pl>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Richard Purdie <richard.purdie@linuxfoundation.org>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The merge commit "526b264 Merge branch 'imx/cleanup' into imx/devel"
left a duplicated mx28_add_mxs_mmc() call, which causes the problem
below during boot.
kobject_add_internal failed for mxs-mmc.1 with -EEXIST, don't try
to register things with the same name in the same directory.
The patch removes this leftover and also change mmc0 adding to align
with mmc1.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
* 'next/cross-platform' of git://git.linaro.org/people/arnd/arm-soc:
arm/imx: use Kconfig choice for low-level debug UART selection
ARM: realview: use Kconfig choice for debug UART selection
ARM: plat-samsung: use Kconfig choice for debug UART selection
ARM: versatile: convert logical CPU numbers to physical numbers
ARM: ux500: convert logical CPU numbers to physical numbers
ARM: shmobile: convert logical CPU numbers to physical numbers
ARM: msm: convert logical CPU numbers to physical numbers
ARM: exynos4: convert logical CPU numbers to physical numbers
Fix up trivial conflict (config DEBUG_S3C_UART move/split vs addition of
ARM_KPROBES_TEST option) in arch/arm/Kconfig.debug
* 'next/devel' of git://git.linaro.org/people/arnd/arm-soc: (50 commits)
ARM: tegra: update defconfig
arm/tegra: Harmony: Configure PMC for low-level interrupts
arm/tegra: device tree support for ventana board
arm/tegra: add support for ventana pinmuxing
arm/tegra: prepare Seaboard pinmux code for derived boards
arm/tegra: pinmux: ioremap registers
gpio/tegra: Convert to a platform device
arm/tegra: Convert pinmux driver to a platform device
arm/dt: Tegra: Add pinmux node to tegra20.dtsi
arm/tegra: Prep boards for gpio/pinmux conversion to pdevs
ARM: mx5: fix clock usage for suspend
ARM i.MX entry-macro.S: remove now unused code
ARM i.MX boards: use CONFIG_MULTI_IRQ_HANDLER
ARM i.MX tzic: add handle_irq function
ARM i.MX avic: add handle_irq function
ARM: mx25: Add the missing IIM base definition
ARM i.MX avic: convert to use generic irq chip
mx31moboard: Add poweroff support
ARM: mach-qong: Add watchdog support
ARM: davinci: AM18x: Add wl1271/wlan support
...
Fix up conflicts in:
arch/arm/mach-at91/at91sam9g45.c
arch/arm/mach-mx5/devices-imx53.h
arch/arm/plat-mxc/include/mach/memory.h
* 'next/board' of git://git.linaro.org/people/arnd/arm-soc: (34 commits)
ep93xx: add support Vision EP9307 SoM
ARM: mxs: Add initial support for DENX MX28
ARM: EXYNOS4: Add support SMDK4412 Board
ARM: EXYNOS4: Add MCT support for EXYNOS4412
ARM: EXYNOS4: Add functions for gic interrupt handling
ARM: EXYNOS4: Add support clock for EXYNOS4412
ARM: EXYNOS4: Add support new EXYNOS4412 SoC
ARM: EXYNOS4: Add support MCT PPI for EXYNOS4212
ARM: EXYNOS4: Add support PPI in external GIC
ARM: EXYNOS4: convert boot_params to atag_offset
ixp4xx: support omicron ixp425 based boards
ARM: EXYNOS4: Add support SMDK4212 Board
ARM: EXYNOS4: Add support PM for EXYNOS4212
ARM: EXYNOS4: Add support clock for EXYNOS4212
ARM: EXYNOS4: Add support new EXYNOS4212 SoC
at91: USB-A9G20 C01 & C11 board support
at91: merge board USB-A9260 and USB-A9263 together
at91: add support for RSIs EWS board
ARM: SAMSUNG: Fix mask value for S5P64X0 CPU IDs
ARM: SAMSUNG: Fix mask for S3C64xx CPU IDs
...
* 'next/fixes' of git://git.linaro.org/people/arnd/arm-soc: (28 commits)
ARM: pxa/cm-x300: properly set bt_reset pin
ARM: mmp: rename SHEEVAD to GPLUGD
ARM: imx: Fix typo 'MACH_MX31_3DS_MXC_NAND_USE_BBT'
ARM: i.MX28: shift frac value in _CLK_SET_RATE
plat-mxc: iomux-v3.h: implicitly enable pull-up/down when that's desired
ARM: mx5: fix clock usage for suspend
ARM: pxa: use correct __iomem annotations
ARM: pxa: sharpsl pm needs SPI
ARM: pxa: centro and treo680 need palm27x
ARM: pxa: make pxafb_smart_*() empty when not enabled
ARM: pxa: select POWER_SUPPLY on raumfeld
ARM: pxa: pxa95x is incompatible with earlier pxa
ARM: pxa: CPU_FREQ_TABLE is needed for CPU_FREQ
ARM: pxa: pxa95x/saarb depends on pxa3xx code
ARM: pxa: allow selecting just one of TREO680/CENTRO
ARM: pxa: export symbols from pxa3xx-ulpi
ARM: pxa: make zylonite_pxa*_init declaration match code
ARM: pxa/z2: fix building error of pxa27x_cpu_suspend() no longer available
ARM: at91: add defconfig for at91sam9g45 family
ARM: at91: remove dependency for Atmel PWM driver selector in Kconfig
...
The exynos4 updates conflict with code from the arm devel-stable branch
and new boards need to set atag_offset in place of boot_param.
Conflicts:
arch/arm/Kconfig
arch/arm/mach-exynos4/include/mach/entry-macro.S
arch/arm/mach-exynos4/mach-smdkc210.c
arch/arm/mach-exynos4/mach-smdkv310.c
arch/arm/mach-exynos4/mct.c
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Noticed when setting SSP0 in clk_set_rate, _CLK_SET_RATE attempts to
reset the clock divider for the SSP0 parent clock, in this case
IO0FRAC. Bits 24-29 of HW_CLKCTRL_FRAC0 are cleared correctly, but
when the new frac value is written the value isn't shifted up to write
the correct bit-field. This results in IO0FRAC being set to 0 and
CPUFRAC being corrupted.
This should occur when writing IO1FRAC, EMIFRAC in HW_CLKCTRL_FRAC0
and GPMIFRAC, HSADCFRAC in HW_CLKCTRL_FRAC1.
Tested on custom i.MX28 board with SSP0 SPI driver.
Signed-off-by: Matt Burtch <matt@grid-net.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Now that the DEBUG_LL UART can be selected by a Kconfig choice,
simplify the #ifdefery in debug-macro.S and add entries to the
top-level Kconfig.debug instead.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Boards used to specify zreladdr in their Makefile.boot with
zreladdr-y := x, so conflicting zreladdrs were silently overwritten.
This patch changes this to zreladdr-y += x, so that we end
up with multiple words in zreladdr in such a case. We can
detect this later and complain if necessary.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This helps resolve the conflicts between the imx cleanups and the
new code that has gone into the imx tree.
Conflict resolution was originally done by Sascha Hauer.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Consolidate mm-mx23.c and mm-mx28.c into a single file.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Some platforms (like OMAP not to name it) are doing rather complicated
hacks just to determine the base UART address to use. Let's give their
addruart macro some slack by providing an extra work register which will
allow for much needed cleanups.
This is basically a no-op as this commit is only adding the extra argument
to the macro but no one is using it yet.
Signed-off-by: nicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Currently framebuffer and MMC devices are registered even if their associated
GPIO pins fail to be requested.
Change the logic so that the registration of such devices only occurs if their
GPIO requests succeeded.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
According to spec, set to 1 is the enable of fractional devide
or the clock can not be generated properly.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
The patch moves MXS_GPIO_NR into mach/mxs.h, so that we only use
standard gpiolib helpers in mach/gpio.h.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
As irq_to_gpio() is only being used by gpio-mxs driver, it should be
moved from mach/gpio.h into gpio-mxs.c.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Rather than marking the mach/gpio.h header files which want to use the
trivial GPIOLIB implementation, mark those which do not want to use it
instead. This means that by default, you get the trivial implementation
and only have to do something extra if you need to. This should
encourage the use of the trivial default implementation.
As an additional bonus, several gpio.h header files become empty.
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Many of the gpio_to_irq implementations use the gpiolib version of this
function. Provide the standard gpiolib gpio_to_irq() for everyone, but
allow platforms to override it if they wish. Add the neccessary
overrides for those platforms which do not use the standard definition.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Consolidate 24 trivial gpiolib implementions out of mach/gpio.h
into asm/gpio.h. This is basically the include of asm-generic/gpio.h
and the definition of gpio_get_value, gpio_set_value, and gpio_cansleep
as described in Documentation/gpio.txt
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: David Brown <davidb@codeaurora.org>
Acked-by: David Brown <davidb@codeaurora.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'next/cross-platform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
ARM: Consolidate the clkdev header files
ARM: set vga memory base at run-time
ARM: convert PCI defines to variables
ARM: pci: make pcibios_assign_all_busses use pci_has_flag
ARM: remove unnecessary mach/hardware.h includes
pci: move microblaze and powerpc pci flag functions into asm-generic
powerpc: rename ppc_pci_*_flags to pci_*_flags
Fix up conflicts in arch/microblaze/include/asm/pci-bridge.h
* 'next/cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (133 commits)
ARM: EXYNOS4: Change devname for FIMD clkdev
ARM: S3C64XX: Cleanup mach/regs-fb.h from mach-s3c64xx
ARM: S5PV210: Cleanup mach/regs-fb.h from mach-s5pv210
ARM: S5PC100: Cleanup mach/regs-fb.h from mach-s5pc100
ARM: S3C24XX: Use generic s3c_set_platdata for devices
ARM: S3C64XX: Use generic s3c_set_platdata for OneNAND
ARM: SAMSUNG: Use generic s3c_set_platdata for NAND
ARM: SAMSUNG: Use generic s3c_set_platdata for USB OHCI
ARM: SAMSUNG: Use generic s3c_set_platdata for HWMON
ARM: SAMSUNG: Use generic s3c_set_platdata for FB
ARM: SAMSUNG: Use generic s3c_set_platdata for TS
ARM: S3C64XX: Add PWM backlight support on SMDK6410
ARM: S5P64X0: Add PWM backlight support on SMDK6450
ARM: S5P64X0: Add PWM backlight support on SMDK6440
ARM: S5PC100: Add PWM backlight support on SMDKC100
ARM: S5PV210: Add PWM backlight support on SMDKV210
ARM: EXYNOS4: Add PWM backlight support on SMDKC210
ARM: EXYNOS4: Add PWM backlight support on SMDKV310
ARM: SAMSUNG: Create a common infrastructure for PWM backlight support
clocksource: convert 32-bit down counting clocksource on S5PV210/S5P64X0
...
Fix up trivial conflict in arch/arm/mach-imx/mach-scb9328.c
* 'next/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (35 commits)
ARM: msm: platsmp: determine number of CPU cores at boot time
ARM: Tegra: Seaboard: Fix I2C bus numbering for ADT7461
ARM: Tegra: Trimslice: Tri-state DAP3 pinmux
ARM: orion5x: fixup 5181 MPP mask check
ARM: mxs-dma: include <linux/dmaengine.h>
ARM: i.MX53: consistently use MX53_UART_PAD_CTRL for uart txd/rxd/rts/cts
ARM: i.MX53: UARTn_CTS pin should not change RTS input select
ARM: i.MX53: UARTn_TXD pin should not change RXD input select
ARM: mx25: Fix typo on CAN1_RX pad setting
iomux-mx53: add missing 'IOMUX_CONFIG_SION' for some I2C pad definitions
ARM: NUC93X: add UL suffix to VMALLOC_END to ensure it is properly typed
ARM: LPC32XXX: add UL suffix to VMALLOC_END to ensure it is properly typed
ARM: CNS3XXX: add UL suffix to VMALLOC_END to ensure it is properly typed
ARM: i.MX53: Fix IOMUX type o's
ARM i.MX dma: Fix burstsize settings
mach-mx5: fix the I2C clock parents
ARM: mxs/tx28: according to the TX28's datasheet D4-D7 are not used for MMC0
ARM i.MX23/28: platform-mxsfb: Add missing include of linux/dma-mapping.h
ARM: mx53: Fix some interrupts marked as reserved.
MXC: iomux-v3: correct NO_PAD_CTRL definition
...
Fix up trivial conflict in arch/arm/mach-imx/mach-mx31_3ds.c
* 'gpio/next' of git://git.secretlab.ca/git/linux-2.6: (61 commits)
gpio/mxc/mxs: fix build error introduced by the irq_gc_ack() renaming
mcp23s08: add i2c support
mcp23s08: isolate spi specific parts
mcp23s08: get rid of setup/teardown callbacks
gpio/tegra: dt: add binding for gpio polarity
mcp23s08: remove unused work queue
gpio/da9052: remove a redundant assignment for gpio->da9052
gpio/mxc: add device tree probe support
ARM: mxc: use ARCH_NR_GPIOS to define gpio number
gpio/mxc: get rid of the uses of cpu_is_mx()
gpio/mxc: add missing initialization of basic_mmio_gpio shadow variables
gpio: Move mpc5200 gpio driver to drivers/gpio
GPIO: DA9052 GPIO module v3
gpio/tegra: Use engineering names in DT compatible property
of/gpio: Add new method for getting gpios under different property names
gpio/dt: Refine GPIO device tree binding
gpio/ml-ioh: fix off-by-one for displaying variable i in dev_err
gpio/pca953x: Deprecate meaningless device-tree bindings
gpio/pca953x: Remove dynamic platform data pointer
gpio/pca953x: Fix IRQ support.
...
Now most of ARM machines has the alsmot same __clk_get/put() macro
So place it at the arch/arm/include/asm/clkdev.h and remove the reduntant header files
But some machines don't have the same form as above. It can use the machince specific clkdev file by HAVE_MACH_CLKDEV config
Now there are only 3 caese.
1) define the clk structure with clkdev macro => Need to move clk structure to proper header file
arch/arm/mach-versatile/include/mach/clkdev.h
arch/arm/mach-realview/include/mach/clkdev.h
arch/arm/mach-vexpress/include/mach/clkdev.h
arch/arm/mach-integrator/include/mach/clkdev.h
2) export the __clk_get/put function at clock.c
arch/arm/mach-shmobile/include/mach/clkdev.h
3) demuxing the clk source
arch/arm/mach-u300/include/mach/clkdev.h
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Other files using dma.h may fail to compile as follows:
In file included from sound/soc/mxs/mxs-pcm.h:22,
from sound/soc/mxs/mxs-saif.h:112,
from sound/soc/mxs/mxs-sgtl5000.c:34:
arch/arm/mach-mxs/include/mach/dma.h:16: warning: 'struct dma_chan' declared inside parameter list
arch/arm/mach-mxs/include/mach/dma.h:16: warning: its scope is only this definition or declaration, which is probably not what you want
arch/arm/mach-mxs/include/mach/dma.h: In function 'mxs_dma_is_apbh':
arch/arm/mach-mxs/include/mach/dma.h:18: error: dereferencing pointer to incomplete type
arch/arm/mach-mxs/include/mach/dma.h: At top level:
arch/arm/mach-mxs/include/mach/dma.h:21: warning: 'struct dma_chan' declared inside parameter list
arch/arm/mach-mxs/include/mach/dma.h: In function 'mxs_dma_is_apbx':
arch/arm/mach-mxs/include/mach/dma.h:23: error: dereferencing pointer to incomplete type
make[3]: *** [sound/soc/mxs/mxs-sgtl5000.o] Error 1
make[2]: *** [sound/soc/mxs] Error 2
make[1]: *** [sound/soc] Error 2
make: *** [sound] Error 2
It seems it's better for dma.h to include dmaengine.h himself.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
It adds LED2 on mx28evk board as heartbeat trigger for diagnostic
purpose.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This allows to move the led definition to .init.rodata.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The pins are actually used (not in mainline yet):
D4 -> SSP2_D0
D5 -> GPIO
D6 -> GPIO
D7 -> GPIO for owire
so their pinmapping for SSP0 is wrong.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Remove linux/mm.h inclusion from netdevice.h -- it's unused (I've checked manually).
To prevent mm.h inclusion via other channels also extract "enum dma_data_direction"
definition into separate header. This tiny piece is what gluing netdevice.h with mm.h
via "netdevice.h => dmaengine.h => dma-mapping.h => scatterlist.h => mm.h".
Removal of mm.h from scatterlist.h was tried and was found not feasible
on most archs, so the link was cutoff earlier.
Hope people are OK with tiny include file.
Note, that mm_types.h is still dragged in, but it is a separate story.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch makes necessary changes on gpio-mxs as below to turn it
into an upstanding gpio driver.
* Clean up the gpio port definition stuff
* Use readl/writel to replace mach-specific accessors
__raw_readl/__raw_writel
* Change mxs_gpio_init into mxs_gpio_probe function
And it then migrates mach-mxs to the updated driver by adding
corresponding platform devices.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
GPIO drivers are getting moved to drivers/gpio for cleanup and
consolidation. This patch moves the mxs driver. Follow up patches
will clean it up and make it a fine upstanding example of a gpio
driver.
v2: Removed header file entirely and put struct definition directly
into driver. The struct isn't used anywhere else in the kernel.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
I get this build error as of today:
arch/arm/mach-mxs/ocotp.c: In function 'mxs_get_ocotp':
arch/arm/mach-mxs/ocotp.c:54: error: implicit declaration of function 'cpu_relax'
make[2]: *** [arch/arm/mach-mxs/ocotp.o] Error 1
Looks like it has been indirectly included before which broke now.
Include it directly.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Convert the MXS timrotv2 32-bit down counting clocksource to the
generic clocksource infrastructure.
Cc: Sascha Hauer <kernel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 47babe69 (mxs: dynamically allocate mmc device) added the ssp
setup and mmc clocks for mx23/28, but forgot to register the mmc clocks
on mx23.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
