Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Checkpatch suggests using ether_addr_copy over memcpy
to copy the mac address.
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit deals with a bunch of checkpatch suggestions
that without changing behavior make checkpatch happier.
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit takes care of the coding style warnings
that are mostly due to a different comment style and
lines over 80 chars, as well as a dangling else.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
checkpatch.pl gave the following error:
ERROR: space required before the open parenthesis '('
+ for(; p < end; p++, offset += 4)
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GPIOlib will print warning messages if we call GPIO functions without a
valid GPIO. Change the code to avoid doing so.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes two BUG_ON() used to notify about RX queue corruptions
on macb (not gem) hardware without actually handling the error.
The new code skips corrupted frames but still processes faultless frames.
Then it resets the RX queue before restarting the reception from a clean
state.
This patch is a rework of an older patch proposed by Neil Armstrong:
http://patchwork.ozlabs.org/patch/371525/
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
macb_interrupt() should not use macb_writel(bp, ISR, <value>) but only
queue_writel(queue, ISR, <value>).
There is one IRQ and one set of {ISR, IER, IDR, IMR} [1] registers per
queue on gem hardware, though only queue0 is actually used for now to
receive frames: other queues can already be used to transmit frames.
The queue_readl() and queue_writel() helper macros are designed to access
the relevant IRQ registers.
[1]
ISR: Interrupt Status Register
IER: Interrupt Enable Register
IDR: Interrupt Disable Register
IMR: Interrupt Mask Register
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Fixes: bfbb92c446 ("net: macb: Handle the RXUBR interrupt on all devices")
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver calls gpiod_set_value() with GPIOD_OUT_* instead of 0 and 1, as
a result the PHY isn't really put back into reset state in macb_remove().
Moreover, the driver assumes that something else has set the GPIO direction
to output, so if it has not, the PHY may not be taken out of reset in
macb_probe() either...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On AT91 SoCs, the User Register (USRIO) exposes a switch to configure the
"Reduced" or "Traditional" version of the Media Independent Interface
(RMII vs. MII or RGMII vs. GMII).
As on the older EMAC version, on GMAC, this switch is set by default to the
non-reduced type of interface, so use the existing capability and extend it to
GMII as well. We then keep the current logic in the macb_init() function.
The capabilities of sama5d2, sama5d4 and sama5d3 GEM interface are updated in
the macb_config structure to be able to properly enable them with a traditional
interface (GMII or MII).
Reported-by: Romain HENRIET <romain.henriet@l-acoustics.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As requested by Rob Herring on patch
https://patchwork.ozlabs.org/patch/580862/.
This is a new property that it's still in net-next and has never been
used in production, so we are not breaking anything with the
incompatible binding change.
Signed-off-by: Sergio Prado <sergio.prado@e-labworks.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tested on Acqua A5 SoM (http://www.acmesystems.it/acqua).
Signed-off-by: Sergio Prado <sergio.prado@e-labworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are getting build warning about:
macb.c:2889:13: warning: 'tx_clk' may be used uninitialized in this function
macb.c:2888:11: warning: 'hclk' may be used uninitialized in this function
In reality they are not used uninitialized as clk_init() will initialize
them, this patch will just silence the warning.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disabling interrupts with the IDR register does not stop the macb hardware
from asserting its interrupt line if there are interrupts pending. Always
clear the interrupts using ISR, and be sure to write it on hardware that
is not read-to-clear, like Zynq. Not doing so will cause interrupts when
the driver doesn't expect them.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Declare a new NP4 SoC variant having USRIO_DISABLED as capability bit.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some platforms, the macb integration does not use the USRIO
register to configure the (R)MII port and clocks.
When the register is not implemented and the MACB error signal
is connected to the bus error, reading or writing to the USRIO
register can trigger some Imprecise External Aborts on ARM platforms.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have mdio_alloc() create the array of interrupt numbers, and
initialize it to POLLING. This is what most MDIO drivers want, so
allowing code to be removed from the drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many Ethernet drivers contain the same netdev_info() print statement
about the attached phy. Move it into the phy device code. Additionally
add a varargs function which can be used to append additional
information.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a phydev_name() function, to help with moving some structure members
from phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of being at the MAC level the reset gpio preperty is moved at the
PHY child node level. It is still managed by the MAC, but from the point
of view of the binding it make more sense to be part of the PHY node.
This commit also fixes a build errors if GPIOLIB is not selected.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With device tree it is no more possible to reset the PHY at board
level. Furthermore, doing in the driver allow to power down the PHY when
the network interface is no more used.
This reset can't be done at the PHY driver level. The PHY must be able to
answer the to the mii bus scan to let the kernel creating a PHY device.
The patch introduces a new optional property "phy-reset-gpios" inspired
from the one use for the FEC.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the sgmii phy interface.
Signed-off-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/s390/net/bpf_jit_comp.c
drivers/net/ethernet/ti/netcp_ethss.c
net/bridge/br_multicast.c
net/ipv4/ip_fragment.c
All four conflicts were cases of simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
If an architecture defines readl/writel using CPP macros, we
get the following kinds of build failure:
> > > drivers/net/ethernet/cadence/macb.c:164:1: error: macro "writel"
> > > passed 3 arguments, but takes just 2
> macb_or_gem_writel(bp, SA1B, bottom);
> ^
Rename the methods so that this doesn't happen.
Signed-off-by: David S. Miller <davem@davemloft.net>
macb_count_tx_descriptors() repeats the generic macro DIV_ROUND_UP(). The patch
does a replacement.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following warnings:
drivers/net/ethernet/cadence/macb.c: In function ‘macb_handle_link_change’:
drivers/net/ethernet/cadence/macb.c:266: warning: comparison between signed and unsigned
drivers/net/ethernet/cadence/macb.c:267: warning: comparison between signed and unsigned
drivers/net/ethernet/cadence/macb.c:291: warning: comparison between signed and unsigned
drivers/net/ethernet/cadence/macb.c: In function ‘gem_update_stats’:
drivers/net/ethernet/cadence/macb.c:1908: warning: comparison between signed and unsigned
drivers/net/ethernet/cadence/macb.c: In function ‘gem_get_ethtool_strings’:
drivers/net/ethernet/cadence/macb.c:1988: warning: comparison between signed and unsigned
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid messages like
macb macb.0 (unnamed net_device) (uninitialized): Cadence caps 0x00000000
macb macb.0 (unnamed net_device) (uninitialized): invalid hw address, using random
let's use dev_*() macros.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 98b5a0f4a2 introduces jumbo frame support, but also it assumes
that macb_config present which is not always true.
The configuration without macb_config fails to boot.
Unable to handle kernel NULL pointer dereference at virtual address 00000010
ptbr = 90350000 pgd = 00000000
Oops: Kernel access of bad area, sig: 11 [#1]
FRAME_POINTER chip: 0x01f:0x1e82 rev 2
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 4.2.0-rc3-next-20150723+ #13
task: 91c26000 ti: 91c28000 task.ti: 91c28000
PC is at macb_probe+0x140/0x61c
Fixes: 98b5a0f4a2 (net: macb: Add support for jumbo frames)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit a50dad355a (net: macb: Add big endian CPU support) converted I/O
accessors to readl_relaxed() and writel_relaxed() and consequentially broke
MACB driver on AVR32 platforms such as ATNGW100.
This patch improves I/O access by checking endiannes first and use the
corresponding methods.
Fixes: a50dad355a (net: macb: Add big endian CPU support)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
JUMBO and NO_GIGABIT_HALF have the same capability masks.
Change one of them.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable SG support for Zynq SOC family devices.
Signed-off-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This howto made sense in the 1990s when users had to manually configure
ISA cards with jumpers or vendor utilities, but with the implementation
of PCI it became increasingly less and less relevant, to the point where
it has been well over a decade since I last updated it. And there is
no value in anyone else taking over updating it either.
However the references to it continue to spread as boiler plate text
from one Kconfig file into the next. We are not doing end users any
favours by pointing them at this old document, so lets kill it with
fire, once and for all, to hopefully stop any further spread.
No code is changed in this commit, just Kconfig help text.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the compatible string for Atmel sama5d2 SoC family as the configuration
options differ from other instances of the GEM.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/cadence/macb.c
drivers/net/phy/phy.c
include/linux/skbuff.h
net/ipv4/tcp.c
net/switchdev/switchdev.c
Switchdev was a case of RTNH_H_{EXTERNAL --> OFFLOAD}
renaming overlapping with net-next changes of various
sorts.
phy.c was a case of two changes, one adding a local
variable to a function whilst the second was removing
one.
tcp.c overlapped a deadlock fix with the addition of new tcp_info
statistic values.
macb.c involved the addition of two zyncq device entries.
skbuff.h involved adding back ipv4_daddr to nf_bridge_info
whilst net-next changes put two other existing members of
that struct into a union.
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the Zynq TRM, gigabit half duplex is not supported. Add a
new cap and compatible string so Zynq can avoid advertising that mode.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Describe the handler for RXUBR better with a new comment.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Reviewied-by: Josh Cartwright <joshc@ni.com>
Reviewied-by: Ben Shelton <ben.shelton@ni.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bitwise tests are always true here because it uses '|' where '&' is
intended.
Fixes: 98b5a0f4a2 ('net: macb: Add support for jumbo frames')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Four minor merge conflicts:
1) qca_spi.c renamed the local variable used for the SPI device
from spi_device to spi, meanwhile the spi_set_drvdata() call
got moved further up in the probe function.
2) Two changes were both adding new members to codel params
structure, and thus we had overlapping changes to the
initializer function.
3) 'net' was making a fix to sk_release_kernel() which is
completely removed in 'net-next'.
4) In net_namespace.c, the rtnl_net_fill() call for GET operations
had the command value fixed, meanwhile 'net-next' adjusted the
argument signature a bit.
This also matches example merge resolutions posted by Stephen
Rothwell over the past two days.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add macb_change_mtu callback; if jumbo frame support is present allow
mtu size changes upto (jumbo max length allowed - headers).
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Reviewed-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable jumbo frame support for Zynq Ultrascale+ MPSoC.
Update the NWCFG register and descriptor length masks accordingly.
Jumbo max length register should be set according to support in SoC; it is
set to 10240 for Zynq Ultrascale+ MPSoC.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Reviewed-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add compatible string and config structure for Zynq Ultrascale+ MPSoC
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Reviewed-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same hardware issue the at91 must work around applies to at least the
Zynq ethernet, and possibly more devices. The driver also needs to handle
the RXUBR interrupt since it turns it on with MACB_RX_INT_FLAGS anyway.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under heavy Rx load, observed that the Hw is updating the USED bit
and it is not updating the received frame status to the BD control
field. This could be lack of resources for processing the BDs at high
data rates. Driver drops the frame associated with this BD but not
clearing the USED bit. So, this is causing hang condition as Hw
expects USED bit to be cleared for this BD.
Signed-off-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 02c958dd3 (net/macb: add TX multiqueue support for gem), the
initialization of tx_head and tx_tail in macb_init_rings() was moved
inside the loop that iterates over each element in the ring. Since
tx_head and tx_tail only need to be assigned once, move them back out of
the loop.
Signed-off-by: Ben Shelton <ben.shelton@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The statistics are grouped by TX and RX errors.
The SQE Test Errors Register indicates problems with TX.
Signed-off-by: Wolfgang Steinwender <wsteinwender@pcs.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we need to check peripheral version from the hardware during probe, I
introduce a little helper to unify these tests. It would prevent to
de-synchronize the test like previously observed.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently need two checks of the peripheral version in MACB_MID register.
One of them got out of sync after modification by 8a013a9c71 (net: macb:
Include multi queue support for xilinx ZynqMP ethernet version).
Fix this in macb_configure_caps() so that xilinx ZynqMP will be considered
as a GEM flavor.
Fixes: 8a013a9c71 ("net: macb: Include multi queue support for xilinx ZynqMP
ethernet version")
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Cc: <stable@vger.kernel.org> #4.0 (if it doesn't make it for -final)
Signed-off-by: David S. Miller <davem@davemloft.net>
User i/o register EMAC_USRIO or GMAC_UR can be found on both macb and gem
flavors of the peripheral. By using the proper accessor, we can add it to the
register dump feature of ethtool.
Increment the version of this API so it can be noticed from user space.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As accessing the peripheral registers need the clocks to be set, we have to
enable them as soon as possible. Their configuration depend on the type of
device used and determined by the DT compatible string. That lead to add
another initialization function in the DT configuration structure.
As the device private structure length depend on an information read in the
registers, we have to store the clock pointers in temporary variables before
feeding the structure fields.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a non-native English speaker, I would correct "capacities" of the macb
peripheral to "capabilities": correct me if I'm wrong!
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
