Pull MIPS updates from Ralf Baechle:
- Improvements to the tlb_dump code
- KVM fixes
- Add support for appended DTB
- Minor improvements to the R12000 support
- Minor improvements to the R12000 support
- Various platform improvments for BCM47xx
- The usual pile of minor cleanups
- A number of BPF fixes and improvments
- Some improvments to the support for R3000 and DECstations
- Some improvments to the ATH79 platform support
- A major patchset for the JZ4740 SOC adding support for the CI20 platform
- Add support for the Pistachio SOC
- Minor BMIPS/BCM63xx platform support improvments.
- Avoid "SYNC 0" as memory barrier when unlocking spinlocks
- Add support for the XWR-1750 board.
- Paul's __cpuinit/__cpuinitdata cleanups.
- New Malta CPU board support large memory so enable ZONE_DMA32.
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (131 commits)
MIPS: spinlock: Adjust arch_spin_lock back-off time
MIPS: asmmacro: Ensure 64-bit FP registers are used with MSA
MIPS: BCM47xx: Simplify handling SPROM revisions
MIPS: Cobalt Don't use module_init in non-modular MTD registration.
MIPS: BCM47xx: Move NVRAM driver to the drivers/firmware/
MIPS: use for_each_sg()
MIPS: BCM47xx: Don't select BCMA_HOST_PCI
MIPS: BCM47xx: Add helper variable for storing NVRAM length
MIPS: IRQ/IP27: Move IRQ allocation API to platform code.
MIPS: Replace smp_mb with release barrier function in unlocks.
MIPS: i8259: DT support
MIPS: Malta: Basic DT plumbing
MIPS: include errno.h for ENODEV in mips-cm.h
MIPS: Define GCR_GIC_STATUS register fields
MIPS: BPF: Introduce BPF ASM helpers
MIPS: BPF: Use BPF register names to describe the ABI
MIPS: BPF: Move register definition to the BPF header
MIPS: net: BPF: Replace RSIZE with SZREG
MIPS: BPF: Free up some callee-saved registers
MIPS: Xtalk: Update xwidget.h with known Xtalk device numbers
...
Pull ARM updates from Russell King:
"Bigger items included in this update are:
- A series of updates from Arnd for ARM randconfig build failures
- Updates from Dmitry for StrongARM SA-1100 to move IRQ handling to
drivers/irqchip/
- Move ARMs SP804 timer to drivers/clocksource/
- Perf updates from Mark Rutland in preparation to move the ARM perf
code into drivers/ so it can be shared with ARM64.
- MCPM updates from Nicolas
- Add support for taking platform serial number from DT
- Re-implement Keystone2 physical address space switch to conform to
architecture requirements
- Clean up ARMv7 LPAE code, which goes in hand with the Keystone2
changes.
- L2C cleanups to avoid unlocking caches if we're prevented by the
secure support to unlock.
- Avoid cleaning a potentially dirty cache containing stale data on
CPU initialisation
- Add ARM-only entry point for secondary startup (for machines that
can only call into a Thumb kernel in ARM mode). Same thing is also
done for the resume entry point.
- Provide arch_irqs_disabled via asm-generic
- Enlarge ARMv7M vector table
- Always use BFD linker for VDSO, as gold doesn't accept some of the
options we need.
- Fix an incorrect BSYM (for Thumb symbols) usage, and convert all
BSYM compiler macros to a "badr" (for branch address).
- Shut up compiler warnings provoked by our cmpxchg() implementation.
- Ensure bad xchg sizes fail to link"
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (75 commits)
ARM: Fix build if CLKDEV_LOOKUP is not configured
ARM: fix new BSYM() usage introduced via for-arm-soc branch
ARM: 8383/1: nommu: avoid deprecated source register on mov
ARM: 8391/1: l2c: add options to overwrite prefetching behavior
ARM: 8390/1: irqflags: Get arch_irqs_disabled from asm-generic
ARM: 8387/1: arm/mm/dma-mapping.c: Add arm_coherent_dma_mmap
ARM: 8388/1: tcm: Don't crash when TCM banks are protected by TrustZone
ARM: 8384/1: VDSO: force use of BFD linker
ARM: 8385/1: VDSO: group link options
ARM: cmpxchg: avoid warnings from macro-ized cmpxchg() implementations
ARM: remove __bad_xchg definition
ARM: 8369/1: ARMv7M: define size of vector table for Vybrid
ARM: 8382/1: clocksource: make ARM_TIMER_SP804 depend on GENERIC_SCHED_CLOCK
ARM: 8366/1: move Dual-Timer SP804 driver to drivers/clocksource
ARM: 8365/1: introduce sp804_timer_disable and remove arm_timer.h inclusion
ARM: 8364/1: fix BE32 module loading
ARM: 8360/1: add secondary_startup_arm prototype in header file
ARM: 8359/1: correct secondary_startup_arm mode
ARM: proc-v7: sanitise and document registers around errata
ARM: proc-v7: clean up MIDR access
...
Move the driver for Ingenic SoC interrupt controllers into
drivers/irqchip where it belongs.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Brian Norris <computersforpeace@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/10147/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move current sa11x0 IRQ driver to the irqchip subsystem.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for Linux 4.1. Most
noteworthy:
- Add more Octeon-optimized crypto functions
- Octeon crypto preemption and locking fixes
- Little endian support for Octeon
- Use correct CSR to soft reset Octeons
- Support LEDs on the Octeon-based DSR-1000N
- Fix PCI interrupt mapping for the Octeon-based DSR-1000N
- Mark prom_free_prom_memory() as __init for a number of systems
- Support for Imagination's Pistachio SOC. This includes arch and
CLK bits. I'd like to merge pinctrl bits later
- Improve parallelism of csum_partial for certain pipelines
- Organize DTB files in subdirs like other architectures
- Implement read_sched_clock for all MIPS platforms other than
Octeon
- Massive series of 38 fixes and cleanups for the FPU emulator /
kernel
- Further FPU remulator work to support new features. This sits on a
separate branch which also has been pulled into the 4.1 KVM branch
- Clean up and fixes for the SEAD3 eval board; remove unused file
- Various updates for Netlogic platforms
- A number of small updates for Loongson 3 platforms
- Increase the memory limit for ATH79 platforms to 256MB
- A fair number of fixes and updates for BCM47xx platforms
- Finish the implementation of XPA support
- MIPS FDC support. No, not floppy controller but Fast Debug Channel :)
- Detect the R16000 used in SGI legacy platforms
- Fix Kconfig dependencies for the SSB bus support"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (265 commits)
MIPS: Makefile: Fix MIPS ASE detection code
MIPS: asm: elf: Set O32 default FPU flags
MIPS: BCM47XX: Fix detecting Microsoft MN-700 & Asus WL500G
MIPS: Kconfig: Disable SMP/CPS for 64-bit
MIPS: Hibernate: flush TLB entries earlier
MIPS: smp-cps: cpu_set FPU mask if FPU present
MIPS: lose_fpu(): Disable FPU when MSA enabled
MIPS: ralink: add missing symbol for RALINK_ILL_ACC
MIPS: ralink: Fix bad config symbol in PCI makefile.
SSB: fix Kconfig dependencies
MIPS: Malta: Detect and fix bad memsize values
Revert "MIPS: Avoid pipeline stalls on some MIPS32R2 cores."
MIPS: Octeon: Delete override of cpu_has_mips_r2_exec_hazard.
MIPS: Fix cpu_has_mips_r2_exec_hazard.
MIPS: kernel: entry.S: Set correct ISA level for mips_ihb
MIPS: asm: spinlock: Fix addiu instruction for R10000_LLSC_WAR case
MIPS: r4kcache: Use correct base register for MIPS R6 cache flushes
MIPS: Kconfig: Fix typo for the r2-to-r6 emulator kernel parameter
MIPS: unaligned: Fix regular load/store instruction emulation for EVA
MIPS: unaligned: Surround load/store macros in do {} while statements
...
This is the main peripheral IRQ controller on the BCM7xxx MIPS chips;
it has the following characteristics:
- 64 to 160+ level IRQs
- Atomic set/clear registers
- Reasonably predictable register layout (N status words, then N
mask status words, then N mask set words, then N mask clear words)
- SMP affinity supported on most systems
- Typically connected to MIPS IRQ 2,3,2,3 on CPUs 0,1,2,3
This driver registers one IRQ domain and one IRQ chip to cover all
instances of the block. Up to 4 instances of the block may appear, as
it supports 4-way IRQ affinity on BCM7435.
The same block exists on the ARM BCM7xxx chips, but typically the ARM GIC
is used instead. So this driver is primarily intended for MIPS STB chips.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: jaedon.shin@gmail.com
Cc: abrestic@chromium.org
Cc: tglx@linutronix.de
Cc: jason@lakedaemon.net
Cc: jogo@openwrt.org
Cc: arnd@arndb.de
Cc: computersforpeace@gmail.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8844/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Tegra's LIC (Legacy Interrupt Controller) has been so far only
supported as a weird extension of the GIC, which is not exactly
pretty.
The stacked IRQ domain framework fits this pretty well, and allows
the LIC code to be turned into a standalone irqchip. In the process,
make the driver DT aware, something that was sorely missing from
the mach-tegra implementation.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1426088583-15097-3-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This adds support for Vybrid's interrupt router. On VF6xx models,
almost all peripherals can be used by either of the two CPU's,
the Cortex-A5 or the Cortex-M4. The interrupt router routes the
peripheral interrupts to the configured CPU.
This IRQ chip driver configures the interrupt router to route
the requested interrupt to the CPU the kernel is running on.
The driver makes use of the irqdomain hierarchy support. The
parent is given by the device tree. This should be one of the
two possible parents either ARM GIC or the ARM NVIC interrupt
controller. The latter is currently not yet supported.
Note that there is no resource control mechnism implemented to
avoid concurrent access of the same peripheral. The user needs
to make sure to use device trees which assign the peripherals
orthogonally. However, this driver warns the user in case the
interrupt is already configured for the other CPU. This provides
a poor man's resource controller.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Link: https://lkml.kernel.org/r/1425249689-32354-2-git-send-email-stefan@agner.ch
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This driver is used to enable System Configuration Register controlled
External, CTI (Core Sight), PMU (Performance Management), and PL310 L2
Cache IRQs prior to use.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lkml.kernel.org/r/1424272444-16230-3-git-send-email-lee.jones@linaro.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add interrupt controller driver to the Conexant CX92755 SoC, part of the
Digicolor SoCs series. Use the generic irq framework support. Use syscon to
access the system global UC_IRQ_CONTROL register.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/5b769e3c23dfa5fde08c4f3bc966c2c2b3921d8a.1421317616.git.baruch@tkos.co.il
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull irq domain ARM updates from Thomas Gleixner:
"This set of changes make use of hierarchical irqdomains to provide:
- MSI/ITS support for GICv3
- MSI support for GICv2m
- Interrupt polarity extender for GICv1
Marc has come more cleanups for the existing extension hooks of GIC in
the pipeline, but they are going to be 3.20 material"
* 'irq-irqdomain-arm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (22 commits)
irqchip: gicv3-its: Fix ITT allocation
irqchip: gicv3-its: Move some alloc/free code to activate/deactivate
irqchip: gicv3-its: Fix domain free in multi-MSI case
irqchip: gic: Remove warning by including linux/irqdomain.h
irqchip: gic-v2m: Add DT bindings for GICv2m
irqchip: gic-v2m: Add support for ARM GICv2m MSI(-X) doorbell
irqchip: mtk-sysirq: dt-bindings: Add bindings for mediatek sysirq
irqchip: mtk-sysirq: Add sysirq interrupt polarity support
irqchip: gic: Support hierarchy irq domain.
irqchip: GICv3: Binding updates for ITS
irqchip: GICv3: ITS: enable compilation of the ITS driver
irqchip: GICv3: ITS: plug ITS init into main GICv3 code
irqchip: GICv3: ITS: DT probing and initialization
irqchip: GICv3: ITS: MSI support
irqchip: GICv3: ITS: device allocation and configuration
irqchip: GICv3: ITS: tables allocators
irqchip: GICv3: ITS: LPI allocator
irqchip: GICv3: ITS: irqchip implementation
irqchip: GICv3: ITS command queue
irqchip: GICv3: rework redistributor structure
...
Pull MIPS updates from Ralf Baechle:
"This is an unusually large pull request for MIPS - in parts because
lots of patches missed the 3.18 deadline but primarily because some
folks opened the flood gates.
- Retire the MIPS-specific phys_t with the generic phys_addr_t.
- Improvments for the backtrace code used by oprofile.
- Better backtraces on SMP systems.
- Cleanups for the Octeon platform code.
- Cleanups and fixes for the Loongson platform code.
- Cleanups and fixes to the firmware library.
- Switch ATH79 platform to use the firmware library.
- Grand overhault to the SEAD3 and Malta interrupt code.
- Move the GIC interrupt code to drivers/irqchip
- Lots of GIC cleanups and updates to the GIC code to use modern IRQ
infrastructures and features of the kernel.
- OF documentation updates for the GIC bindings
- Move GIC clocksource driver to drivers/clocksource
- Merge GIC clocksource driver with clockevent driver.
- Further updates to bring the GIC clocksource driver up to date.
- R3000 TLB code cleanups
- Improvments to the Loongson 3 platform code.
- Convert pr_warning to pr_warn.
- Merge a bunch of small lantiq and ralink fixes that have been
staged/lingering inside the openwrt tree for a while.
- Update archhelp for IP22/IP32
- Fix a number of issues for Loongson 1B.
- New clocksource and clockevent driver for Loongson 1B.
- Further work on clk handling for Loongson 1B.
- Platform work for Broadcom BMIPS.
- Error handling cleanups for TurboChannel.
- Fixes and optimization to the microMIPS support.
- Option to disable the FTLB.
- Dump more relevant information on machine check exception
- Change binfmt to allow arch to examine PT_*PROC headers
- Support for new style FPU register model in O32
- VDSO randomization.
- BCM47xx cleanups
- BCM47xx reimplement the way the kernel accesses NVRAM information.
- Random cleanups
- Add support for ATH25 platforms
- Remove pointless locking code in some PCI platforms.
- Some improvments to EVA support
- Minor Alchemy cleanup"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (185 commits)
MIPS: Add MFHC0 and MTHC0 instructions to uasm.
MIPS: Cosmetic cleanups of page table headers.
MIPS: Add CP0 macros for extended EntryLo registers
MIPS: Remove now unused definition of phys_t.
MIPS: Replace use of phys_t with phys_addr_t.
MIPS: Replace MIPS-specific 64BIT_PHYS_ADDR with generic PHYS_ADDR_T_64BIT
PCMCIA: Alchemy Don't select 64BIT_PHYS_ADDR in Kconfig.
MIPS: lib: memset: Clean up some MIPS{EL,EB} ifdefery
MIPS: iomap: Use __mem_{read,write}{b,w,l} for MMIO
MIPS: <asm/types.h> fix indentation.
MAINTAINERS: Add entry for BMIPS multiplatform kernel
MIPS: Enable VDSO randomization
MIPS: Remove a temporary hack for debugging cache flushes in SMTC configuration
MIPS: Remove declaration of obsolete arch_init_clk_ops()
MIPS: atomic.h: Reformat to fit in 79 columns
MIPS: Apply `.insn' to fixup labels throughout
MIPS: Fix microMIPS LL/SC immediate offsets
MIPS: Kconfig: Only allow 32-bit microMIPS builds
MIPS: signal.c: Fix an invalid cast in ISA mode bit handling
MIPS: mm: Only build one microassembler that is suitable
...
ARM GICv2m specification extends GICv2 to support MSI(-X) with
a new register frame. This allows a GICv2 based system to support
MSI with minimal changes.
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
[maz: converted the driver to use stacked irq domains,
updated changelog]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1416941243-7181-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Mediatek SoCs have interrupt polarity support in sysirq which
allows to invert polarity for given interrupt. Add this support
using hierarchy irq domain.
Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Link: https://lkml.kernel.org/r/1416902662-19281-3-git-send-email-yingjoe.chen@mediatek.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Move GIC irqchip support to drivers/irqchip/ and rename the Kconfig
option from IRQ_GIC to MIPS_GIC to avoid confusion with the ARM GIC.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Qais Yousef <qais.yousef@imgtec.com>
Tested-by: Qais Yousef <qais.yousef@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jeffrey Deans <jeffrey.deans@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7812/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some chips, such as BCM6328, only require bcm7120-l2. Some BCM7xxx STB
configurations only require brcmstb-l2. Treat them as two separate
entities, and update the mach-bcm dependencies to reflect the change.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lkml.kernel.org/r/1415342669-30640-13-git-send-email-cernekee@gmail.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Pull irq updates from Thomas Gleixner:
"The irq departement delivers:
- a cleanup series to get rid of mindlessly copied code.
- another bunch of new pointlessly different interrupt chip drivers.
Adding homebrewn irq chips (and timers) to SoCs must provide a
value add which is beyond the imagination of mere mortals.
- the usual SoC irq controller updates, IOW my second cat herding
project"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (44 commits)
irqchip: gic-v3: Implement CPU PM notifier
irqchip: gic-v3: Refactor gic_enable_redist to support both enabling and disabling
irqchip: renesas-intc-irqpin: Add minimal runtime PM support
irqchip: renesas-intc-irqpin: Add helper variable dev = &pdev->dev
irqchip: atmel-aic5: Add sama5d4 support
irqchip: atmel-aic5: The sama5d3 has 48 IRQs
Documentation: bcm7120-l2: Add Broadcom BCM7120-style L2 binding
irqchip: bcm7120-l2: Add Broadcom BCM7120-style Level 2 interrupt controller
irqchip: renesas-irqc: Add binding docs for new R-Car Gen2 SoCs
irqchip: renesas-irqc: Add DT binding documentation
irqchip: renesas-intc-irqpin: Document SoC-specific bindings
openrisc: Get rid of handle_IRQ
arm64: Get rid of handle_IRQ
ARM: omap2: irq: Convert to handle_domain_irq
ARM: imx: tzic: Convert to handle_domain_irq
ARM: imx: avic: Convert to handle_domain_irq
irqchip: or1k-pic: Convert to handle_domain_irq
irqchip: atmel-aic5: Convert to handle_domain_irq
irqchip: atmel-aic: Convert to handle_domain_irq
irqchip: gic-v3: Convert to handle_domain_irq
...
Just move the code over as it has no dependencies
on arch/arm/ anymore.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds support for the Level-2 interrupt controller
hardware found in Broadcom Set Top Box System-on-a-Chip devices. This
interrupt controller is implemented using a single enable register.
This interrupt controller is always present on the platforms supported
by the irq-brcmstb-l2 driver, hence the reason why both are compiled
using the same Kconfig symbol.
[jac] removed the following warning:
drivers/irqchip/irq-bcm7120-l2.c: In function 'bcm7120_l2_intc_irq_handle':
drivers/irqchip/irq-bcm7120-l2.c:49:27: warning: unused variable 'gc' [-Wunused-variable]
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lkml.kernel.org/r/1410309862-27784-2-git-send-email-f.fainelli@gmail.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
HiP04 GIC is the variate of ARM GICv2.
ARM GICv2 supports 8 cores. HiP04 GIC extends to support 16 cores. It
results that bit fields in GIC_DIST_TARGET & GIC_DIST_SOFTINT are
different from ARM GICv2. And the maximium IRQ is downgrade from 1020 to 510.
Since different register offset & bitfields definitation breaks
compartible with ARM GICv2, create a new hip04 irq driver.
And this driver is derived from irq-gic.c to support the Hisilicon HiP04
interrupt controller, which is similar to the GIC, but deviates at some
points. Support for power management, non-banked registers, cascaded
GICs (and multiple controllers in general) and bigLittle support has
been removed from the GIC driver.
Affinity related functions have been adjusted to match the Hisilicon
hardware implementation.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Link: https://lkml.kernel.org/r/1407408695-19626-9-git-send-email-haojian.zhuang@linaro.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
On Keystone SOCs, DSP cores can send interrupts to ARM
host using the IRQ controller IP. It provides 28 IRQ
signals to ARM. The IRQ handler running on HOST OS can
identify DSP signal source by analyzing SRCCx bits in
IPCARx registers. This is one of the component used by
the IPC mechanism used on Keystone SOCs.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lkml.kernel.org/r/1406126430-9978-1-git-send-email-grygorii.strashko@ti.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add AIC (Advanced Interrupt Controller) and AIC5 (AIC5 is an evolution of
the AIC block) drivers.
Put common code in irq-atmel-aic-common.c/.h so that both driver can access
shared functions (this will ease maintenance).
These drivers are only compatible with dt enabled board and replace the
old implementation found in arch/arm/mach-at91/irq.c.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Link: https://lkml.kernel.org/r/1405012462-766-4-git-send-email-boris.brezillon@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Generic Interrupt Controller (version 3) offers services that are
similar to GICv2, with a number of additional features:
- Affinity routing based on the CPU MPIDR (ARE)
- System register for the CPU interfaces (SRE)
- Support for more that 8 CPUs
- Locality-specific Peripheral Interrupts (LPIs)
- Interrupt Translation Services (ITS)
This patch adds preliminary support for GICv3 with ARE and SRE,
non-secure mode only. It relies on higher exception levels to grant ARE
and SRE access.
Support for LPI and ITS will be added at a later time.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Zi Shen Lim <zlim@broadcom.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Tirumalesh Chalamarla <tchalamarla@cavium.com>
Reviewed-by: Yun Wu <wuyun.wu@huawei.com>
Reviewed-by: Zhen Lei <thunder.leizhen@huawei.com>
Tested-by: Tirumalesh Chalamarla<tchalamarla@cavium.com>
Tested-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
Acked-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lkml.kernel.org/r/1404140510-5382-3-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
A few GICv2 low-level function are actually very useful to GICv3,
and it makes some sense to share them across the two drivers.
They end-up in their own file, with an additional parameter used
to ensure an optional synchronization (unused on GICv2).
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1404140510-5382-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
In addition to consolidating the or1k-pic with other interrupt
controllers, this makes OpenRISC less tied to its on-cpu
interrupt controller.
All or1k-pic specific parts are moved out of irq.c and into
drivers/irqchip/irq-or1k-pic.c
In that transition, the functionality have been divided into
three chip variants.
One that handles level triggered interrupts, one that handles edge
triggered interrupts and one that handles the interrupt
controller that is present in the or1200 OpenRISC cpu
implementation.
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Link: https://lkml.kernel.org/r/1401136302-27654-1-git-send-email-stefan.kristiansson@saunalahti.fi
Acked-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds support for the Level-2 interrupt controller hardware
found in Broadcom Set Top Box System-on-a-Chip devices. This interrupt
controller is implemented using the generic IRQ chip driver with
separate enable and disable registers.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Link: https://lkml.kernel.org/r/1400892054-24457-2-git-send-email-f.fainelli@gmail.com
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
These changes are mostly for ARM specific device drivers that either
don't have an upstream maintainer, or that had the maintainer ask
us to pick up the changes to avoid conflicts. A large chunk of this
are clock drivers (bcm281xx, exynos, versatile, shmobile), aside from
that, reset controllers for STi as well as a large rework of the
Marvell Orion/EBU watchdog driver are notable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=u/FI
-----END PGP SIGNATURE-----
Merge tag 'drivers-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Arnd Bergmann:
"These changes are mostly for ARM specific device drivers that either
don't have an upstream maintainer, or that had the maintainer ask us
to pick up the changes to avoid conflicts.
A large chunk of this are clock drivers (bcm281xx, exynos, versatile,
shmobile), aside from that, reset controllers for STi as well as a
large rework of the Marvell Orion/EBU watchdog driver are notable"
* tag 'drivers-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
Revert "dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac."
Revert "net: stmmac: Add SOCFPGA glue driver"
ARM: shmobile: r8a7791: Fix SCIFA3-5 clocks
ARM: STi: Add reset controller support to mach-sti Kconfig
drivers: reset: stih416: add softreset controller
drivers: reset: stih415: add softreset controller
drivers: reset: Reset controller driver for STiH416
drivers: reset: Reset controller driver for STiH415
drivers: reset: STi SoC system configuration reset controller support
dts: socfpga: Add sysmgr node so the gmac can use to reference
dts: socfpga: Add support for SD/MMC on the SOCFPGA platform
reset: Add optional resets and stubs
ARM: shmobile: r7s72100: fix bus clock calculation
Power: Reset: Generalize qnap-poweroff to work on Synology devices.
dts: socfpga: Update clock entry to support multiple parents
ARM: socfpga: Update socfpga_defconfig
dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
net: stmmac: Add SOCFPGA glue driver
watchdog: orion_wdt: Use %pa to print 'phys_addr_t'
drivers: cci: Export CCI PMU revision
...
Lots of changes specific to one of the SoC families. Some that
stick out are:
* mach-qcom gains new features, most importantly SMP support for
the newer chips (Stephen Boyd, Rohit Vaswani)
* mvebu gains support for three new SoCs: Armada 375, 380 and 385
(Thomas Petazzoni and Free-electrons team)
* SMP support for Rockchips (Heiko Stübner)
* Lots of i.MX changes (Shawn Guo)
* Added support for BCM5301x SoC (Hauke Mehrtens)
* Multiplatform support for Marvell Kirkwood and Dove
(Andrew Lunn and Sebastian Hesselbarth doing the final part
of a long journey)
* Unify davinci platforms and remove obsolete ones (Sekhar Nori,
Arnd Bergmann)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=AGpV
-----END PGP SIGNATURE-----
Merge tag 'soc-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC specific changes from Arnd Bergmann:
"Lots of changes specific to one of the SoC families. Some that stick
out are:
- mach-qcom gains new features, most importantly SMP support for the
newer chips (Stephen Boyd, Rohit Vaswani)
- mvebu gains support for three new SoCs: Armada 375, 380 and 385
(Thomas Petazzoni and Free-electrons team)
- SMP support for Rockchips (Heiko Stübner)
- Lots of i.MX changes (Shawn Guo)
- Added support for BCM5301x SoC (Hauke Mehrtens)
- Multiplatform support for Marvell Kirkwood and Dove (Andrew Lunn
and Sebastian Hesselbarth doing the final part of a long journey)
- Unify davinci platforms and remove obsolete ones (Sekhar Nori, Arnd
Bergmann)"
* tag 'soc-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (126 commits)
ARM: sunxi: Select HAVE_ARM_ARCH_TIMER
ARM: cache-tauros2: remove ARMv6 code
ARM: mvebu: don't select CONFIG_NEON
ARM: davinci: fix DT booting with default defconfig
ARM: configs: bcm_defconfig: enable bcm590xx regulator support
ARM: davinci: remove tnetv107x support
MAINTAINERS: Update ARM STi maintainers
ARM: restrict BCM_KONA_UART to ARCH_BCM_MOBILE
ARM: bcm21664: Add board support.
ARM: sunxi: Add the new watchog compatibles to the reboot code
ARM: enable ARM_HAS_SG_CHAIN for multiplatform
ARM: davinci: remove da8xx_omapl_defconfig
ARM: davinci: da8xx: fix multiple watchdog device registration
ARM: davinci: add da8xx specific configs to davinci_all_defconfig
ARM: davinci: enable da8xx build concurrently with older devices
ARM: BCM5301X: workaround suppress fault
ARM: BCM5301X: add early debugging support
ARM: BCM5301X: initial support for the BCM5301X/BCM470X SoCs with ARM CPU
ARM: mach-bcm: Remove GENERIC_TIME
ARM: shmobile: APMU: Fix warnings due to improper printk formats
...
Looks like people wanted these merged via the omap tree as it's
the only user for the GIC crossbar.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=MLEE
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.15/crossbar-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/drivers
Merge OMAP crossbar support from Tony Lindgren:
Add support for GIC crossbar that routes interrupts on newer omaps.
Looks like people wanted these merged via the omap tree as it's
the only user for the GIC crossbar.
* tag 'omap-for-v3.15/crossbar-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: DRA: Enable Crossbar IP support for DRA7XX
ARM: OMAP4+: Correct Wakeup-gen code to use physical irq number
DRIVERS: IRQCHIP: CROSSBAR: Add support for Crossbar IP
DRIVERS: IRQCHIP: IRQ-GIC: Add support for routable irqs
Signed-off-by: Olof Johansson <olof@lixom.net>
This reverts commit 40b367d95f.
Russell King has raised the idea of creating a proper PMU driver for
this SoC that would incorporate the functionality currently in this
driver. It would also cover the use case for the graphics subsystem on
this SoC.
To prevent having to maintain the devicetree ABI for this limited
interrupt-handler driver, we revert the driver before it hits a mainline
tagged release (eg v3.15).
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@googlemail.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Link: http://lkml.kernel.org/r/1393911160-7688-1-git-send-email-jason@lakedaemon.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This adds the irqchip driver for Cirrus Logic CLPS711X series SoCs.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull irq updates from Thomas Gleixner:
"This lot provides:
* Bugfixes for armada irq controller
* Updates to renesas irq chip
* Support for the TI-NSPIRE irq controller
Not strictly a bug fix only pull request, but important updates for
some of the arm Socs which I completely forgot to send last week.
Seems like my obliviousness is getting worse, I just can't remember
when it started"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: Add support for TI-NSPIRE irqchip
irqchip: renesas-irqc: Enable mask on suspend
irqchip: renesas-irqc: Use lazy disable
irqchip: armada-370-xp: fix MSI race condition
irqchip: armada-370-xp: fix IPI race condition
Some socs have a large number of interrupts requests to service
the needs of its many peripherals and subsystems. All of the
interrupt lines from the subsystems are not needed at the same
time, so they have to be muxed to the irq-controller appropriately.
In such places a interrupt controllers are preceded by an CROSSBAR
that provides flexibility in muxing the device requests to the controller
inputs.
This driver takes care a allocating a free irq and then configuring the
crossbar IP as a part of the mpu's irqchip callbacks. crossbar_init should
be called right before the irqchip_init, so that it is setup to handle the
irqchip callbacks.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Kumar Gala <galak@codeaurora.org> (for DT binding portion)
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=JT1d
-----END PGP SIGNATURE-----
Merge tag 'xtensa-next-20140123' of git://github.com/czankel/xtensa-linux
Pull Xtensa patches from Chris Zankel:
"The major changes are adding support for SMP for Xtensa, fixing and
cleaning up the ISS (simulator) network driver, and better support for
device trees"
* tag 'xtensa-next-20140123' of git://github.com/czankel/xtensa-linux: (40 commits)
xtensa: implement ndelay
xtensa: clean up udelay
xtensa: enable HAVE_PERF_EVENTS
xtensa: remap io area defined in device tree
xtensa: support default device tree buses
xtensa: initialize device tree clock sources
xtensa: xtfpga: fix definitions of platform devices
xtensa: standardize devicetree cpu compatible strings
xtensa: avoid duplicate of IO range definitions
xtensa: fix ATOMCTL register documentation
xtensa: Enable irqs after cpu is set online
xtensa: ISS: raise network polling rate to 10 times/sec
xtensa: remove unused XTENSA_ISS_NETWORK Kconfig parameter
xtensa: ISS: avoid simple_strtoul usage
xtensa: Switch to sched_clock_register()
xtensa: implement CPU hotplug
xtensa: add SMP support
xtensa: add MX irqchip
xtensa: clear timer IRQ unconditionally in its handler
xtensa: clean up do_interrupt/do_IRQ
...
This patch adds support for the interrupt controllers found in some
TI-Nspire models.
FIQ support was taken out to simplify the driver code and may be added
in later. Since Linux on this platform doesn't really use FIQs, this
wasn't really that important in the first place.
[ tglx: Made zevio_handle_irq static and reordered __init functions ]
Signed-off-by: Daniel Tang <dt.tangr@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Link: http://lkml.kernel.org/r/1386223937-12189-1-git-send-email-dt.tangr@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
MX is an interrupt distributor used in some SMP-capable xtensa
configurations.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
Extract xtensa built-in interrupt controller implementation from
xtensa/kernel/irq.c and move it to other irqchips, providing way to
instantiate it from the device tree.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
This adds an irqchip driver and corresponding devicetree binding for the
secondary interrupt controllers based on Synopsys DesignWare IP dw_apb_ictl.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Dove has a Power Management Unit with its own interrupt
controller. This is chained on the main interrupt controller. Add a
driver, making use of generic chip where possible.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
cc: devicetree@vger.kernel.org
cc: pawel.moll@arm.com
cc: mark.rutland@arm.com
cc: swarren@wwwdotorg.org
cc: ian.campbell@citrix.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
