This reverts commit 5946fdaee4.
The original commit's assumption that the secondary port is
unconnected turns out to be false.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Markku Pesonen <tourula@gmail.com>
Fixes: 5946fdaee4 ("pata_atiixp: Don't use unconnected secondary port on SB600/SB700")
Cc: Darren Stevens <darren@stevens-zone.net>
This SATA controller is quite similar to the one present on the DA850
SoC, but the PHY configuration is different and it supports two HBA
ports.
The IP suffers from the same PMP issue the DA850 does - if we enable
PMP but don't use it - softreset fails. Appropriate workaround was
implemented in this driver as well.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This driver is orphan since commit b2026f708e ("ARM: at91: remove
at91sam9260/at91sam9g20 legacy board support"). Given that nobody cared
adding DT support to it, it probably means it's no longer used and is
thus a good candidate for removal.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes the following sparse warning:
drivers/ata/libata-core.c:4913:6: warning: symbol 'ata_sg_clean' was not
declared. Should it be static?
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Use setup_deferrable_timer() instead of init_timer_deferrable() to
simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Sata ecc is controlled by only 1 bit which is 24bit in big-endian
in ecc register. So only setting 24bit to disable sata ecc prevents
other bits from being overwritten in ecc register.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Both archs should work just fine with libata subsystem nowadays.
Suggested-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Delete error handling from the result of a call to platform_get_resource()
when the value is immediately passed to devm_ioremap_resource().
Signed-off-by: Belen Sarabia <belensarabia@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
ata_sff_qc_issue() expects upper layers to never issue commands on a
command protocol that it doesn't implement. While the assumption
holds fine with the usual IO path, nothing filters based on the
command protocol in the passthrough path (which was added later),
allowing the warning to be tripped with a passthrough command with the
right (well, wrong) protocol.
Failing with AC_ERR_SYSTEM is the right thing to do anyway. Remove
the unnecessary WARN.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Link: http://lkml.kernel.org/r/CACT4Y+bXkvevNZU8uP6X0QVqsj6wNoUA_1exfTSOzc+SmUtMOA@mail.gmail.com
Signed-off-by: Tejun Heo <tj@kernel.org>
Without this patch, failed probe would not free resources like irq.
ata port tdev object currently hold a reference to the ata port
object. Therefore the ata port object release function will not get
called until the ata_tport_release is called. But that would never
happen, releasing the last reference of ata port dev is done by
scsi_host_release, which is called by ata_host_release when the ata
port object is released.
The ata device objects actually do not need to explicitly hold a
reference to their real counterpart, given the transport objects are
the children of these objects and device_add() is call for each child.
We know the parent will not be deleted until we call the child's
device_del().
Reported-by: Matthew Whitehead <tedheadster@gmail.com>
Tested-by: Matthew Whitehead <tedheadster@gmail.com>
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Declare of_device_id structures as const as they are either passed to
the macro MODULE_DEVICE_TABLE or stored in the of_match_table field of a
device_driver structure. This field is of type const, so of_device_id
structures having this property can be made const too.
Cross compiled the files drivers/ata/pata_macio.c and
drivers/ata/pata_mpc52xx.c for powerpc architecture.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This is the set of stuff that didn't quite make the initial pull and a
set of fixes for stuff which did. The new stuff is basically lpfc
(nvme), qedi and aacraid. The fixes cover a lot of previously
submitted stuff, the most important of which probably covers some of
the failing irq vectors allocation and other fallout from having the
SCSI command allocated as part of the block allocation functions.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=e+6v
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"This is the set of stuff that didn't quite make the initial pull and a
set of fixes for stuff which did.
The new stuff is basically lpfc (nvme), qedi and aacraid. The fixes
cover a lot of previously submitted stuff, the most important of which
probably covers some of the failing irq vectors allocation and other
fallout from having the SCSI command allocated as part of the block
allocation functions"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (59 commits)
scsi: qedi: Fix memory leak in tmf response processing.
scsi: aacraid: remove redundant zero check on ret
scsi: lpfc: use proper format string for dma_addr_t
scsi: lpfc: use div_u64 for 64-bit division
scsi: mac_scsi: Fix MAC_SCSI=m option when SCSI=m
scsi: cciss: correct check map error.
scsi: qla2xxx: fix spelling mistake: "seperator" -> "separator"
scsi: aacraid: Fixed expander hotplug for SMART family
scsi: mpt3sas: switch to pci_alloc_irq_vectors
scsi: qedf: fixup compilation warning about atomic_t usage
scsi: remove scsi_execute_req_flags
scsi: merge __scsi_execute into scsi_execute
scsi: simplify scsi_execute_req_flags
scsi: make the sense header argument to scsi_test_unit_ready mandatory
scsi: sd: improve TUR handling in sd_check_events
scsi: always zero sshdr in scsi_normalize_sense
scsi: scsi_dh_emc: return success in clariion_std_inquiry()
scsi: fix memory leak of sdpk on when gd fails to allocate
scsi: sd: make sd_devt_release() static
scsi: qedf: Add QLogic FastLinQ offload FCoE driver framework.
...
Fix typos and add the following to the scripts/spelling.txt:
followings||following
While we are here, add a missing colon in the boilerplate in DT binding
documents. The "you SoC" in allwinner,sunxi-pinctrl.txt was fixed as
well.
I reworded "as the followings:" to "as follows:" for
drivers/usb/gadget/udc/renesas_usb3.c.
Link: http://lkml.kernel.org/r/1481573103-11329-32-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Driver updates for ARM SoCs.
A handful of driver changes this time around. The larger changes are:
- Reset drivers for hi3660 and zx2967
- AHCI driver for Davinci, acked by Tejun and brought in here due to
platform dependencies
- Cleanups of atmel-ebi (External Bus Interface)
- Tweaks for Rockchip GRF (General Register File) usage (kitchensink misc
register range on the SoCs)
- PM domains changes for support of two new ZTE SoCs (zx296718 and zx2967)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=od7u
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs.
A handful of driver changes this time around. The larger changes are:
- Reset drivers for hi3660 and zx2967
- AHCI driver for Davinci, acked by Tejun and brought in here due to
platform dependencies
- Cleanups of atmel-ebi (External Bus Interface)
- Tweaks for Rockchip GRF (General Register File) usage (kitchensink
misc register range on the SoCs)
- PM domains changes for support of two new ZTE SoCs (zx296718 and
zx2967)"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (53 commits)
soc: samsung: pmu: Add register defines for pad retention control
reset: make zx2967 explicitly non-modular
reset: core: fix reset_control_put
soc: samsung: pm_domains: Read domain name from the new label property
soc: samsung: pm_domains: Remove message about failed memory allocation
soc: samsung: pm_domains: Remove unused name field
soc: samsung: pm_domains: Use full names in subdomains registration log
sata: ahci-da850: un-hardcode the MPY bits
sata: ahci-da850: add a workaround for controller instability
sata: ahci: export ahci_do_hardreset() locally
sata: ahci-da850: implement a workaround for the softreset quirk
sata: ahci-da850: add device tree match table
sata: ahci-da850: get the sata clock using a connection id
soc: samsung: pmu: Remove duplicated define for ARM_L2_OPTION register
memory: atmel-ebi: Enable the SMC clock if specified
soc: samsung: pmu: Remove unused and duplicated defines
memory: atmel-ebi: Properly handle multiple reference to the same CS
memory: atmel-ebi: Fix the test to enable generic SMC logic
soc: samsung: pm_domains: Add new Exynos5433 compatible
soc: samsung: pmu: Add dummy support for Exynos5433 SoC
...
All but one caller want the decoded sense header, so offer the existing
__scsi_execute helper as the public scsi_execute API to simply the
callers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull libata updates from Tejun Heo:
- Bartlomiej added pata_falcon
- Christoph is trying to remove use of static 4k buf. It's still WIP
- config cleanup around HAS_DMA
- other fixes and driver-specific changes
* 'for-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (29 commits)
ata: pata_of_platform: using of_property_read_u32() helper
pata_atiixp: Don't use unconnected secondary port on SB600/SB700
libata-sff: Don't scan disabled ports when checking for legacy mode.
pata_octeon_cf: remove unused local variables from octeon_cf_set_piomode()
ahci: qoriq: added ls2088a platforms support
ahci: qoriq: report error when ecc register address is missing in dts
ahci: qoriq: added a condition to enable dma coherence
Revert "libata: switch to dynamic allocation instead of ata_scsi_rbuf"
ahci: imx: fix building without hwmon or thermal
ata: add Atari Falcon PATA controller driver
ata: pass queued command to ->sff_data_xfer method
ata: allow subsystem to be used on m68k arch
libata: switch to dynamic allocation instead of ata_scsi_rbuf
libata: don't call ata_scsi_rbuf_fill for command without a response buffer
libata: call ->scsi_done from ata_scsi_simulate
libata: remove the done callback from ata_scsi_args
libata: move struct ata_scsi_args to libata-scsi.c
libata: avoid global response buffer in atapi_qc_complete
libata-eh: Use switch() instead of sparse array for protocol strings
ata: sata_mv: Convert to devm_ioremap_resource()
...
This update includes the usual round of major driver updates (ncr5380,
ufs, lpfc, be2iscsi, hisi_sas, storvsc, cxlflash, aacraid,
megaraid_sas, ). There's also an assortment of minor fixes and the
major update of switching a bunch of drivers to pci_alloc_irq_vectors
from Christoph.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=cBQx
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This update includes the usual round of major driver updates (ncr5380,
ufs, lpfc, be2iscsi, hisi_sas, storvsc, cxlflash, aacraid,
megaraid_sas, ...).
There's also an assortment of minor fixes and the major update of
switching a bunch of drivers to pci_alloc_irq_vectors from Christoph"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (188 commits)
scsi: megaraid_sas: handle dma_addr_t right on 32-bit
scsi: megaraid_sas: array overflow in megasas_dump_frame()
scsi: snic: switch to pci_irq_alloc_vectors
scsi: megaraid_sas: driver version upgrade
scsi: megaraid_sas: Change RAID_1_10_RMW_CMDS to RAID_1_PEER_CMDS and set value to 2
scsi: megaraid_sas: Indentation and smatch warning fixes
scsi: megaraid_sas: Cleanup VD_EXT_DEBUG and SPAN_DEBUG related debug prints
scsi: megaraid_sas: Increase internal command pool
scsi: megaraid_sas: Use synchronize_irq to wait for IRQs to complete
scsi: megaraid_sas: Bail out the driver load if ld_list_query fails
scsi: megaraid_sas: Change build_mpt_mfi_pass_thru to return void
scsi: megaraid_sas: During OCR, if get_ctrl_info fails do not continue with OCR
scsi: megaraid_sas: Do not set fp_possible if TM capable for non-RW syspdIO, change fp_possible to bool
scsi: megaraid_sas: Remove unused pd_index from megasas_build_ld_nonrw_fusion
scsi: megaraid_sas: megasas_return_cmd does not memset IO frame to zero
scsi: megaraid_sas: max_fw_cmds are decremented twice, remove duplicate
scsi: megaraid_sas: update can_queue only if the new value is less
scsi: megaraid_sas: Change max_cmd from u32 to u16 in all functions
scsi: megaraid_sas: set pd_after_lb from MR_BuildRaidContext and initialize pDevHandle to MR_DEVHANDLE_INVALID
scsi: megaraid_sas: latest controller OCR capability from FW before sending shutdown DCMD
...
Instead define the timeout behavior purely based on the host_template
eh_timed_out method and wire up the existing transport implementations
in the host templates. This also clears up the confusion that the
transport template method overrides the host template one, so some
drivers have to re-override the transport template one.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This can be used to check for fs vs non-fs requests and basically
removes all knowledge of BLOCK_PC specific from the block layer,
as well as preparing for removing the cmd_type field in struct request.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
All platforms using this driver now register the SATA refclk. Remove
the hardcoded default value from the driver and instead read the rate
of the external clock and calculate the required MPY value from it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Tejun Heo <tj@kernel.org>
[nsekhar@ti.com: fix checkpatch warning about an unneeded else]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
We have a use case with the da850 SATA controller where at PLL0
frequency of 456MHz (needed to properly service the LCD controller)
the chip becomes unstable and the hardreset operation is ignored the
first time 50% of times.
The sata core driver already retries to resume the link because some
controllers ignore writes to the SControl register, but just retrying
the resume operation doesn't work - we need to issue he phy/wake reset
again to make it work.
Reimplement ahci_hardreset() in the driver and poke the controller a
couple times before really giving up.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
We need a way to retrieve the information about the online state of
the link in the ahci-da850 driver.
Create a new function: ahci_do_hardreset() which is called from
ahci_hardreset() for backwards compatibility, but has an additional
argument: 'online' - which can be used to check if the link is online
after this function returns.
The new routine will be used in the ahci-da850 driver to avoid code
duplication when implementing a workaround for tha da850 SATA
controller quirk/instability.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
There's an issue with the da850 SATA controller: if port multiplier
support is compiled in, but we're connecting the drive directly to
the SATA port on the board, the drive can't be detected.
To make SATA work on the da850-lcdk board: first try to softreset
with pmp - if the operation fails with -EBUSY, retry without pmp.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
We're using device tree for da850-lcdk. Add the match table to allow
to probe the driver.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
In preparation for using two clocks in the driver (the sysclk2-based
clock and the external REFCLK), check if we got the functional clock
after calling ahci_platform_get_resources(). If not, retry calling
clk_get() with con_id specified.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
And require all drivers that want to support BLOCK_PC to allocate it
as the first thing of their private data. To support this the legacy
IDE and BSG code is switched to set cmd_size on their queues to let
the block layer allocate the additional space.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
The SB600 and SB700 southbridge chips from ATI/AMD only have
connections for the primary IDE port. As these chips have unique
pci device ID's use these to mark the secondary port as 'dummy'
Signed-off-by: Darren Stevens <darren@stevens-zone.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
libata-sff.c checks for legacy mode by testing if both primary and
secondary ports on a controller are in legacy mode and selects legacy
if either one is. However on some south bridge chips (e.g AMD
SB600/SB700) the secondary port is not wired, and when it is disabled
by setting the disable bit in the PCI header it appears as a fixed
legacy port.
Prevent incorrect detection by not testing ports that are marked as
'dummy'
tj: Addressed Sergei's review points. Other style edits.
Signed-off-by: Darren Stevens <darren@stevens-zone.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
@t1 and @t2i are calculated along with @t2 but never used. Drop them.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: David Binderman <dcb314@hotmail.com>
Ls2088a is new introduced arm-based soc with sata support with
following features:
1. Complies with the serial ATA 3.0 specification and the AHCI 1.3.1
specification
2. Contains a high-speed descriptor-based DMA controller
3. Supports the following:
a. Speeds of 1.5 Gb/s (first-generation SATA), 3 Gb/s
(second-generation SATA), and 6 Gb/s (third-generation SATA)
b. FIS-based switching
c. Native command queuing (NCQ) commands
d. Port multiplier operation
e. Asynchronous notification
f. SATA BIST mode
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
For ls1021a, and armv8 chasis 2 socs, sata ecc must be disabled.
If ecc register is not found in sata node in dts, report error.
This is a chip erratum described as bellow:
The Read DMA operations get early termination indication from the
controller. This issue is observed as CRC error in the status registers.
The issue is due to address collision at address 0 in the dual port
memory. The read is a dummy read to flush out the header, but due to
collision the controller logs the mbit error reported by the ECC check
logic. This results in the early termination of the Read DMA operation
by the controller. The issue happens to all the interface
speeds(GEN1/2/3) for all the products.
Workaround:
Disable ECC feature on those platforms.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Enable DMA coherence in SATA controller on condition that
dma-coherent property exists in sata node in DTS.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This reverts commit a234f7395c.
The commit tried to get rid of the shared global SCSI response buffer.
Unfortunately, it added blocking allocation to atomic path. Revert it
for now.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Christoph Hellwig <hch@lst.de>
When CONFIG_HWMON is disabled, we now get a link failure:
ERROR: "devm_hwmon_device_register_with_groups" [drivers/ata/ahci_imx.ko] undefined!
drivers/ata/ahci_imx.o: In function `imx_ahci_probe':
ahci_imx.c:(.text.imx_ahci_probe+0x304): undefined reference to `devm_thermal_zone_of_sensor_register'
This makes the code calling into the hwmon subsystem compile-time
conditional, and adds a Kconfig dependency to avoid the corner
case of having HWMON=m and AHCI_IMX=y, by forcing AHCI_IMX=m in this
case. The thermal subsystem already has a check in its header, but
that also doesn't cover the THERMAL=m case, so we need a somewhat
complex Kconfig expression to handle all cases.
Fixes: 54643a83b4 ("ahci: imx: Add imx53 SATA temperature sensor support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add Atari Falcon PATA controller driver. The major difference
when compared to legacy IDE's falconide host driver is that we
are using polled PIO mode and thus avoiding the need for STDMA
locking magic altogether.
Tested under ARAnyM emulator.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
For Atari Falcon PATA support we need to check the current command
in its ->sff_data_xfer method. Update core code and all users
accordingly.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
When libata was merged m68k lacked IOMAP support. This has not been
true for a long time now so allow subsystem to be used on m68k.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Note of the emulated commands in the pageout/pagein path, so just do
a GFP_NOIO dynamic allocation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
No need to copy a zeroed buffer to the caller if the command is defined
to not have a response in the SCSI spec.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
We always need to call ->scsi_done after we've finished emulating a
command, so do it in a single place at the end of ata_scsi_simulate.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
It's always the scsi_done callback, and we can get at that easily
in the place where ->done is called.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
It's only used in libata-scsi.c, so move it closer to the users.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
We only need to look at 4 bytes of the inquiry response for ATAPI
devices. Instead of using the global ata_scsi_rbuf just use a
a stack buffer. Also factor the fixup into it's own little helper
function to make it more readable.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Replace the sparse 256-pointer array for looking up protocol strings by
a switch() statement to reduce kernel size.
According to bloat-o-meter, this saves 910 bytes on m68k (32-bit), and
1892 bytes on arm64 (64-bit).
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Convert to devm_ioremap_resource() which provides more consistent error
handling.
Note that devm_ioremap_resource() provides its own error messages.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Here, If devm_ioremap will fail. It will return NULL.
Then hpriv->base = NULL - 0x20000; Kernel can run into
a NULL-pointer dereference. This error check will avoid
NULL pointer dereference.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
For an ATA device supporting the sense data reporting feature set, a
failed command will trigger the execution of ata_eh_request_sense if
the result task file of the failed command has the ATA_SENSE bit set
(sense data available bit). ata_eh_request_sense executes the REQUEST
SENSE DATA EXT command to retrieve the sense data of the failed
command. On success of REQUEST SENSE DATA EXT, the ATA_SENSE bit will
NOT be set (the command succeeded) but ata_eh_request_sense
nevertheless tests the availability of sense data by testing that bit
presence in the result tf of the REQUEST SENSE DATA EXT command. This
leads us to falsely assume that request sense data failed and to the
warning message:
atax.xx: request sense failed stat 50 emask 0
Upon success of REQUEST SENSE DATA EXT, set the ATA_SENSE bit in the
result task file command so that sense data can be returned by
ata_eh_request_sense.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Add a hwmon entry to get the temperature from the die of imx53
SATA.
The original patch was made by Richard Zhu for kernel 2.6.x:
ENGR00134041-MX53-Add-the-SATA-AHCI-temperature-monitor.patch
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.co.uk>
Signed-off-by: Tejun Heo <tj@kernel.org>
Marko reports that CX1-JB512-HP shows the same timeout issues as
CX1-JB256-HP. Let's apply MAX_SEC_128 to all devices in the series.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Marko Koski-Vähälä <marko@koski-vahala.com>
Cc: stable@vger.kernel.org # v3.19+
acpi_get_object_info() allocates the returned structure, which the
caller has to free when the call succeeds. Free it when appropriate.
Fixes: c9802a4be6 ("ata: ahci_xgene: Add AHCI Support for 2nd HW version of APM X-Gene SoC AHCI SATA Host controller.")
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Signed-off-by: Tejun Heo <tj@kernel.org>
If NO_DMA=y:
ERROR: "bad_dma_ops" [drivers/ata/libata.ko] undefined!
To fix this, protect the DMA code by #ifdef CONFIG_HAS_DMA, and provide
dummies of ata_sg_clean() and ata_sg_setup() for the !CONFIG_HAS_DMA
case.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Commit 70e6ad0c6d ("[PATCH] libata: prepare ata_sg_clean() for
invocation from EH") made ata_sg_clean() global, but no user outside
libata-core.c has ever materialized.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull another libata patch from Tejun Heo:
"One more patch from Adam added.
It makes libata skip probing for NCQ prio unless the feature is
explicitly requested by the user. This is necessary because some
controllers lock up after the optional feature is probed"
* 'for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ata: avoid probing NCQ Prio Support if not explicitly requested
Previously, when the ata device was being initialized we were
probing for NCQ prio support by checking the identify information
and also checking the log page that holds information about ncq prio
support.
This caused an error on an Intel HBA so the code is now updated to
only probe for NCQ prio support when the sysfs variable controlling
NCQ prio support is enabled.
tj: Update formatting, switch to spin_[un]lock_irq() and update
locking a bit, use REVALIDATE instead of RESET, and return -EIO
instead of -EINVAL on config failure.
Signed-off-by: Adam Manzanares <adam.manzanares@wdc.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata updates from Tejun Heo:
- Adam added opt-in ATA command priority support.
- There are machines which hide multiple nvme devices behind an ahci
BAR. Dan Williams proposed a solution to force-switch the mode but
deemed too hackishd. People are gonna discuss the proper way to
handle the situation in nvme standard meetings. For now, detect and
warn about the situation.
- Low level driver specific changes.
Christoph Hellwig pipes in about the hidden nvme warning:
"I wish that was the case. We've pretty much agreed that we'll want to
implement it as a virtual PCIe root bridge, similar to Intels other
'innovation' VMD that we work around that way.
But Intel management has apparently decided that they don't want to
spend more cycles on this now that Lenovo has an optional BIOS that
doesn't force this broken mode anymore, and no one outside of Intel
has enough information to implement something like this.
So for now I guess this warning is it, until Intel reconsideres and
spends resources on fixing up the damage their Chipset people caused"
* 'for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: warn about remapped NVMe devices
ahci-remap.h: add ahci remapping definitions
nvme: move NVMe class code to pci_ids.h
pata: imx: support controller modes up to PIO4
pata: imx: add support of setting timings for PIO modes
pata: imx: set controller PIO mode with .set_piomode callback
pata: imx: sort headers out
ata: set ncq_prio_enabled iff device has support
ata: ATA Command Priority Disabled By Default
ata: Enabling ATA Command Priorities
block: Add iocontext priority to request
ahci: qoriq: added ls1046a platform support
It's another busy cycle for the docs tree, as the sphinx conversion
continues. Highlights include:
- Further work on PDF output, which remains a bit of a pain but should be
more solid now.
- Five more DocBook template files converted to Sphinx. Only 27 to go...
Lots of plain-text files have also been converted and integrated.
- Images in binary formats have been replaced with more source-friendly
versions.
- Various bits of organizational work, including the renaming of various
files discussed at the kernel summit.
- New documentation for the device_link mechanism.
...and, of course, lots of typo fixes and small updates.
-----BEGIN PGP SIGNATURE-----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=A0EV
-----END PGP SIGNATURE-----
Merge tag 'docs-4.10' of git://git.lwn.net/linux
Pull documentation update from Jonathan Corbet:
"These are the documentation changes for 4.10.
It's another busy cycle for the docs tree, as the sphinx conversion
continues. Highlights include:
- Further work on PDF output, which remains a bit of a pain but
should be more solid now.
- Five more DocBook template files converted to Sphinx. Only 27 to
go... Lots of plain-text files have also been converted and
integrated.
- Images in binary formats have been replaced with more
source-friendly versions.
- Various bits of organizational work, including the renaming of
various files discussed at the kernel summit.
- New documentation for the device_link mechanism.
... and, of course, lots of typo fixes and small updates"
* tag 'docs-4.10' of git://git.lwn.net/linux: (193 commits)
dma-buf: Extract dma-buf.rst
Update Documentation/00-INDEX
docs: 00-INDEX: document directories/files with no docs
docs: 00-INDEX: remove non-existing entries
docs: 00-INDEX: add missing entries for documentation files/dirs
docs: 00-INDEX: consolidate process/ and admin-guide/ description
scripts: add a script to check if Documentation/00-INDEX is sane
Docs: change sh -> awk in REPORTING-BUGS
Documentation/core-api/device_link: Add initial documentation
core-api: remove an unexpected unident
ppc/idle: Add documentation for powersave=off
Doc: Correct typo, "Introdution" => "Introduction"
Documentation/atomic_ops.txt: convert to ReST markup
Documentation/local_ops.txt: convert to ReST markup
Documentation/assoc_array.txt: convert to ReST markup
docs-rst: parse-headers.pl: cleanup the documentation
docs-rst: fix media cleandocs target
docs-rst: media/Makefile: reorganize the rules
docs-rst: media: build SVG from graphviz files
docs-rst: replace bayer.png by a SVG image
...
SCT Write Same support had been introduced with
commit 7b20309428 ("libata: Add support for SCT Write Same")
Some problems, namely excessive userspace segfaults, had been reported at
http://lkml.kernel.org/r/20160908192736.GA4356@gmail.com
This lead to commit 0ce1b18c42 ("libata: Some drives failing on
SCT Write Same") which strived to disable SCT Write Same on !ZAC devices.
Due to the way this was done and to the logic in sd_config_write_same(),
this didn't work for those devices that have
->max_ws_blocks > SD_MAX_WS10_BLOCKS: for these, ->no_write_same and
->max_write_same_sectors would still be non-zero,
but ->ws10 == ->ws16 == 0. This would cause sd_setup_write_same_cmnd() to
demultiplex REQ_OP_WRITE_SAME requests to WRITE_SAME, and these in turn
aren't supported by libata-scsi:
EXT4-fs (dm-1): Delayed block allocation failed for inode 2625094 at
logical offset 2032 with max blocks 2 with error 121
EXT4-fs (dm-1): This should not happen!! Data will be lost
121 == EREMOTEIO is what scsi_io_completion() asserts in case of
invalid opcodes.
Back to the original problem of userspace segfaults: this can be tracked
down to ata_format_sct_write_same() overwriting the input page. Sometimes,
this page is ZERO_PAGE(0) which ceases to be filled with zeros from that
point on. Since ZERO_PAGE(0) is used for userspace .bss mappings, code of
the following is doomed:
static char *a = NULL; /* .bss */
...
if (a)
*a = 'a';
This problem is not solved by disabling SCT Write Same for !ZAC devices
only.
It can certainly be fixed, but the final release is quite close -- so
disable SCT Write Same for all ATA devices rather than introducing some
SCT key buffer allocation schemes at this point.
Fixes: 7b20309428 ("libata: Add support for SCT Write Same")
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Some Intel ahci implementations have a completely broken remapping mode
where they hide one or more NVMe devices behind the bar of an AHCI device.
Intel refuses to let the OS reprogram the BIOS to switch out of this
mode at runtime, and so far we're not come up with another good way
to undo the mess that the Chipset people created. So for now the only
thing we can do is to alert users about this situation and switch to the
faster and much saner so called "AHCI" mode insted of the RAID mode in
the BIOS so that the BIOS does not hide the NVMe devices from us.
The sitation is even worse as at least one vendor (thanks a lot Lenovo..)
has started hardcoding their BIOS into the "RAID" mode even for laptops
that don't use AHCI _at all_ and just have a single NVMe device. For now
there is an unspported Linux-only BIOS that undoes this braindamage,
but we'll have to see if things are getting better or worse from here.
Based on an earlier patch from Dan Williams <dan.j.williams@intel.com>.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
If the nr-ports property is missing ata_host_alloc_pinfo is called with
n_ports = 0. This results in host->ports[0] = NULL which later makes
mv_init_host() oops when dereferencing this pointer.
Instead be a bit more cooperative and fail the probing with an error
message.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Don't try to guess what the errors from pci_irq_alloc_vectors mean, as
that's too fragile. Instead always try allocating a single vector
when multi-MSI mode fails. This makes various intel Desktop and
Laptop CPUs use MSI again.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Michael Marley <michael@michaelmarley.com>
Tested-by: Michael Marley <michael@michaelmarley.com>
Fixes: 0b9e2988ab ("ahci: use pci_alloc_irq_vectors")
Signed-off-by: Tejun Heo <tj@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYHmoCAAoJEHm+PkMAQRiG7RMIAI2i7Y5hpL5yCxK5AFaL4u/G
KxXfp1B1UanUTgjOmd7zGqtDYcFX9t7GTTUFixQ7/9Opr4PD9qbnatoDGSc3xjbT
msDgA1B78F1/Q3kHWfeGq32MihQ4mj5NwUCo+igUcUvvWG7mHgzErj/Nh5RoobQX
p/izdpTbrw3GX6xXB8olbG7XWHaVye/+TT3q6+gmgm8I/QEujcLeGoycE0zlhPN8
FG/JX76At/+ZM2Py7Oxo3k+oKL9CHrtOQYDp/wN0uslV5eYvvkZz0/M1HMOGZt+c
gZU5jzM17K7C4Nzo06WAuBU9wUBGc25m+cPicLlOmljnzfU+f50SKaDjZq3p7QI=
=2KUF
-----END PGP SIGNATURE-----
Merge tag 'v4.9-rc4' into sound
Bring in -rc4 patches so I can successfully merge the sound doc changes.
Having timing settings for all supported by the controller PIO modes
now it is possible to expand its PIO mask.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The controller is capable to operate in up to PIO4 mode, however
before the change the driver relies on timing settings done by
a bootloader for PIO0 mode only. The change adds more flexibility
in PIO mode selection at runtime and makes the driver to work even if
bootloader does not preset ATA timings.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Convert .set_mode callback function to more specific .set_piomode,
the driver does not have support of DMA modes, thus a simpler version
of the callback is preferred.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
There's a typo in ata_gen_passthru_sense(), where the first byte
would be overwritten incorrectly later on.
Reported-by: Charles Machalow <csm10495@gmail.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Fixes: 11093cb1ef ("libata-scsi: generate correct ATA pass-through sense")
Cc: stable@vger.kernel.org # v4.7+
Signed-off-by: Tejun Heo <tj@kernel.org>
We need to make sure hpriv->irq is set properly if we don't use per-port
vectors, so switch from blindly assigning pdev->irq to using
pci_irq_vector, which handles all interrupt types correctly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Robert Richter <robert.richter@cavium.com>
Tested-by: Robert Richter <robert.richter@cavium.com>
Tested-by: David Daney <ddaney.cavm@gmail.com>
Fixes: 0b9e2988ab ("ahci: use pci_alloc_irq_vectors")
Signed-off-by: Tejun Heo <tj@kernel.org>
The previous patch renamed several files that are cross-referenced
along the Kernel documentation. Adjust the links to point to
the right places.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
commit 17a51f12 ("ahci: only try to use multi-MSI mode if there is more
than 1 port") lead to a case where nvec isn't initialized before it's
used. Fix this by moving the check into the n_ports conditional.
Reported-and-reviewed-by Colin Ian King <colin.king@canonical.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
We previously had a check to see if the device has support for
prioritized ncq commands and a check to see if a device flag
is set, through a sysfs variable, in order to send a prioritized
command.
This patch only allows the sysfs variable to be set if the device
supports prioritized commands enabling one check in ata_build_rw_tf
in order to determine whether or not to send a prioritized command.
This patch depends on ata: ATA Command Priority Disabled By Default
tj: Minor subject and formatting updates.
Signed-off-by: Adam Manzanares <adam.manzanares@wdc.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add a sysfs entry to turn on priority information being passed
to a ATA device. By default this feature is turned off.
This patch depends on ata: Enabling ATA Command Priorities
tj: Renamed ncq_prio_on to ncq_prio_enable and removed trivial
ata_ncq_prio_on() and open-coded the test.
Signed-off-by: Adam Manzanares <adam.manzanares@hgst.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch checks to see if an ATA device supports NCQ command priorities.
If so and the user has specified an iocontext that indicates
IO_PRIO_CLASS_RT then we build a tf with a high priority command.
This is done to improve the tail latency of commands that are high
priority by passing priority to the device.
tj: Removed trivial ata_ncq_prio_enabled() and open-coded the test.
Signed-off-by: Adam Manzanares <adam.manzanares@hgst.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
We should only try to allocate multiple MSI or MSI-X vectors if the device
actually has multiple ports. Otherwise pci_alloc_irq_vectors will return
a single vector due to n_ports = 1, in which case we shouldn't set the
AHCI_HFLAG_MULTI_MSI flag.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Fixes: 0b9e2988 ("ahci: use pci_alloc_irq_vectors")
Reported-by: Emmanuel Benisty <benisty.e@gmail.com>
Tested-by: Emmanuel Benisty <benisty.e@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This reverts commit 640847298e ("ahci: qoriq: Disable NCQ
on ls2080a SoC")
The erratum has been fixed in ls2080a v2.0 and later soc.
In reality, customer will not get any ls2080a v1.0 soc. Neither apply
to any products. So reverting this commit won't create any side effect.
Blacklisting v2.0 could also be a option, but that needs to check the
soc version which is not suitable in the driver.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Replacing dma_pool_alloc and memset with a single call to dma_pool_zalloc
Signed-off-by: Harman Kalra <harman4linux@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Restrict support SCT Write Same to devices which also support ZAC where
support is required.
Reported-by: Mike Krinkin <krinkin.m.u@gmail.com>
Signed-off-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Use the new pci_alloc_irq_vectors API to allocate MSI-X and MSI vectors.
The big advantage over the old code is that we can use the same API for
MSI and MSI-X, and that we don't need to store the MSI-X vector mapping
in driver-private data structures.
This first conversion keeps the probe order as-is: MSI-X multi vector,
MSI multi vector, MSI single vector, MSI-X single vector and last a
single least legacy interrupt line. There is one small change of
behavior: we now check the "MSI Revert to Single Message" flag for
MSI-X in addition to MSI.
Because the API to find the Linux IRQ number for a MSI/MSI-X vector
is PCI specific, but libahaci is bus-agnostic I had to a
get_irq_vector function pointer to struct ahci_host_priv. The
alternative would be to move the multi-vector case of ahci_host_activate
to ahci.c and just call ata_host_activate directly from the others
users of ahci_host_activate.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Ninja32 needs to set some flags to indicate it does 32bit IO. However it currently assigns this which
loses the initializing flag and causes a warning spew. Fix it to use a logical or as is intended.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Tested-by: Ellmar Stelnberger <estellnb@elstel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Use non DMA write log when ATA_DFLAG_PIO is set.
Signed-off-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Tejun Heo <tj@kernel.org>
Correct handling of devices with sector_size other that 512 bytes.
In the case of a 4Kn device sector_size it is possible to describe a much
larger DSM Trim than the current fixed default of 512 bytes.
This patch assumes the minimum descriptor is sector_size and fills out
the descriptor accordingly.
The ACS-2 specification is quite clear that the DSM command payload is
sized as number of 512 byte transfers so a 4Kn device will operate
correctly without this patch.
Signed-off-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Acked-by: Tejun Heo <tj@kernel.org>
SATA drives may support write same via SCT. This is useful
for setting the drive contents to a specific pattern (0's).
Translate a SCSI WRITE SAME 16 command to be either a DSM TRIM
command or an SCT Write Same command.
Based on the UNMAP flag:
- When set translate to DSM TRIM
- When not set translate to SCT Write Same
Signed-off-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Tejun Heo <tj@kernel.org>
Safely overwriting the attached page to ATA format from the SCSI formatted
variant.
Signed-off-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Tejun Heo <tj@kernel.org>
irq already contains the interrupt number for the port, don't add the
port index to it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: d684a90d38 ("ahci: per-port msix support")
Cc: stable@vger.kernel.org v4.5+
Despite ST AHCI version = 1.3, reading HOST_PORTS_IMPL
returns 0. So force_port_map to 1 by using ports-implemented
DT property.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
By default the SATA IP on the qoriq SoCs does not generating
coherent/snoopable transactions. This patch enable it in the
sata axicc register.
In addition, the dma-coherent property must be set on the
SATA controller nodes.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The default values for Port Phy2Cfg register and
Port Phy3Cfg register are better, no need to overwrite them.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
scsi_done() was called repeatedly and apparently because of that,
the kernel would call trace when we touch the Control mode page:
Call Trace:
[<ffffffff812ea0d2>] dump_stack+0x63/0x81
[<ffffffff81079cfb>] __warn+0xcb/0xf0
[<ffffffff81079e2d>] warn_slowpath_null+0x1d/0x20
[<ffffffffa00f51b0>] ata_eh_finish+0xe0/0xf0 [libata]
[<ffffffffa00fb830>] sata_pmp_error_handler+0x640/0xa50 [libata]
[<ffffffffa00470ed>] ahci_error_handler+0x1d/0x70 [libahci]
[<ffffffffa00f55f0>] ata_scsi_port_error_handler+0x430/0x770 [libata]
[<ffffffffa00eff8d>] ? ata_scsi_cmd_error_handler+0xdd/0x160 [libata]
[<ffffffffa00f59d7>] ata_scsi_error+0xa7/0xf0 [libata]
[<ffffffffa00913ba>] scsi_error_handler+0xaa/0x560 [scsi_mod]
[<ffffffffa0091310>] ? scsi_eh_get_sense+0x180/0x180 [scsi_mod]
[<ffffffff81098eb8>] kthread+0xd8/0xf0
[<ffffffff815d913f>] ret_from_fork+0x1f/0x40
[<ffffffff81098de0>] ? kthread_worker_fn+0x170/0x170
---[ end trace 8b7501047e928a17 ]---
Removed the unnecessary code and let ata_scsi_translate() do the job.
Also, since ata_mselect_control() has no ATA command to send to the
device, ata_scsi_mode_select_xlat() should return 1 for it, so that
ata_scsi_translate() will finish early to avoid ata_qc_issue().
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
