commit f5e9bda03a upstream.
When orientation switch is enabled in ucsi glink, there is a xhci
probe failure seen when booting up in host mode in reverse
orientation.
During bootup the following things happen in multiple drivers:
a) DWC3 controller driver initializes the core in device mode when the
dr_mode is set to DRD. It relies on role_switch call to change role to
host.
b) QMP driver initializes the lanes to TYPEC_ORIENTATION_NORMAL as a
normal routine. It relies on the typec_switch_set call to get notified
of orientation changes.
c) UCSI core reads the UCSI_GET_CONNECTOR_STATUS via the glink and
provides initial role switch to dwc3 controller.
When booting up in host mode with orientation TYPEC_ORIENTATION_REVERSE,
then we see the following things happening in order:
a) UCSI gives initial role as host to dwc3 controller ucsi_register_port.
Upon receiving this notification, the dwc3 core needs to program GCTL from
PRTCAP_DEVICE to PRTCAP_HOST and as part of this change, it asserts GCTL
Core soft reset and waits for it to be completed before shifting it to
host. Only after the reset is done will the dwc3_host_init be invoked and
xhci is probed. DWC3 controller expects that the usb phy's are stable
during this process i.e., the phy init is already done.
b) During the 100ms wait for GCTL core soft reset, the actual notification
from PPM is received by ucsi_glink via pmic glink for changing role to
host. The pmic_glink_ucsi_notify routine first sends the orientation
change to QMP and then sends role to dwc3 via ucsi framework. This is
happening exactly at the time GCTL core soft reset is being processed.
c) When QMP driver receives typec switch to TYPEC_ORIENTATION_REVERSE, it
then re-programs the phy at the instant GCTL core soft reset has been
asserted by dwc3 controller due to which the QMP PLL lock fails in
qmp_combo_usb_power_on.
d) After the 100ms of GCTL core soft reset is completed, the dwc3 core
goes for initializing the host mode and invokes xhci probe. But at this
point the QMP is non-responsive and as a result, the xhci plat probe fails
during xhci_reset.
Fix this by passing orientation switch to available ucsi instances if
their gpio configuration is available before ucsi_register is invoked so
that by the time, the pmic_glink_ucsi_notify provides typec_switch to QMP,
the lane is already configured and the call would be a NOP thus not racing
with role switch.
Cc: stable@vger.kernel.org
Fixes: c6165ed2f4 ("usb: ucsi: glink: use the connector orientation GPIO to provide switch events")
Suggested-by: Wesley Cheng <quic_wcheng@quicinc.com>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240301040914.458492-1-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a587a0352 upstream.
It is possible trigger below warning message from mass storage function,
WARNING: CPU: 6 PID: 3839 at drivers/usb/gadget/udc/core.c:294 usb_ep_queue+0x7c/0x104
pc : usb_ep_queue+0x7c/0x104
lr : fsg_main_thread+0x494/0x1b3c
Root cause is mass storage function try to queue request from main thread,
but other thread may already disable ep when function disable.
As there is no function failure in the driver, in order to avoid effort
to fix warning, change WARN_ON_ONCE() in usb_ep_queue() to pr_debug().
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
Signed-off-by: yuan linyu <yuanlinyu@hihonor.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240315020144.2715575-1-yuanlinyu@hihonor.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f4d1960764 upstream.
The show and store callback routines for the "disable" sysfs attribute
file in port.c acquire the device lock for the port's parent hub
device. This can cause problems if another process has locked the hub
to remove it or change its configuration:
Removing the hub or changing its configuration requires the
hub interface to be removed, which requires the port device
to be removed, and device_del() waits until all outstanding
sysfs attribute callbacks for the ports have returned. The
lock can't be released until then.
But the disable_show() or disable_store() routine can't return
until after it has acquired the lock.
The resulting deadlock can be avoided by calling
sysfs_break_active_protection(). This will cause the sysfs core not
to wait for the attribute's callback routine to return, allowing the
removal to proceed. The disadvantage is that after making this call,
there is no guarantee that the hub structure won't be deallocated at
any moment. To prevent this, we have to acquire a reference to it
first by calling hub_get().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/f7a8c135-a495-4ce6-bd49-405a45e7ea9a@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee113b860a upstream.
Create hub_get() and hub_put() routines to encapsulate the kref_get()
and kref_put() calls in hub.c. The new routines will be used by the
next patch in this series.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/604da420-ae8a-4a9e-91a4-2d511ff404fb@rowland.harvard.edu
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 80ba43e9f7 upstream.
Among the attribute file callback routines in
drivers/usb/core/sysfs.c, the interface_authorized_store() function is
the only one which acquires a device lock on an ancestor device: It
calls usb_deauthorize_interface(), which locks the interface's parent
USB device.
The will lead to deadlock if another process already owns that lock
and tries to remove the interface, whether through a configuration
change or because the device has been disconnected. As part of the
removal procedure, device_del() waits for all ongoing sysfs attribute
callbacks to complete. But usb_deauthorize_interface() can't complete
until the device lock has been released, and the lock won't be
released until the removal has finished.
The mechanism provided by sysfs to prevent this kind of deadlock is
to use the sysfs_break_active_protection() function, which tells sysfs
not to wait for the attribute callback.
Reported-and-tested by: Yue Sun <samsun1006219@gmail.com>
Reported by: xingwei lee <xrivendell7@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/linux-usb/CAEkJfYO6jRVC8Tfrd_R=cjO0hguhrV31fDPrLrNOOHocDkPoAA@mail.gmail.com/#r
Fixes: 310d2b4124 ("usb: interface authorization: SysFS part of USB interface authorization")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1c37eea1-9f56-4534-b9d8-b443438dc869@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9aa41130a upstream.
If the device is configured for system wakeup, then make sure that the
xHCI driver knows about it and make sure to permit wakeup only at the
appropriate time.
For host mode, if the controller goes through the dwc3 code path, then a
child xHCI platform device is created. Make sure the platform device
also inherits the wakeup setting for xHCI to enable remote wakeup.
For device mode, make sure to disable system wakeup if no gadget driver
is bound. We may experience unwanted system wakeup due to the wakeup
signal from the controller PMU detecting connection/disconnection when
in low power (D3). E.g. In the case of Steam Deck, the PCI PME prevents
the system staying in suspend.
Cc: stable@vger.kernel.org
Reported-by: Guilherme G. Piccoli <gpiccoli@igalia.com>
Closes: https://lore.kernel.org/linux-usb/70a7692d-647c-9be7-00a6-06fc60f77294@igalia.com/T/#mf00d6669c2eff7b308d1162acd1d66c09f0853c7
Fixes: d07e8819a0 ("usb: dwc3: add xHCI Host support")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Tested-by: Sanath S <Sanath.S@amd.com>
Tested-by: Guilherme G. Piccoli <gpiccoli@igalia.com> # Steam Deck
Link: https://lore.kernel.org/r/667cfda7009b502e08462c8fb3f65841d103cc0a.1709865476.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f37e76abd6 upstream.
The m.u.component_create.pid field is for debugging and in the mainline
kernel it's not used anything. However, it still needs to be set to
something to prevent disclosing uninitialized stack data. Set it to
zero.
Fixes: 7b3ad5abf0 ("staging: Import the BCM2835 MMAL-based V4L2 camera driver.")
Cc: stable <stable@kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/2d972847-9ebd-481b-b6f9-af390f5aabd3@moroto.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef25725b7f upstream.
gcc-14 warns about this strncpy() that results in a non-terminated
string for an overflow:
In file included from include/linux/string.h:369,
from drivers/staging/vc04_services/vchiq-mmal/mmal-vchiq.c:20:
In function 'strncpy',
inlined from 'create_component' at drivers/staging/vc04_services/vchiq-mmal/mmal-vchiq.c:940:2:
include/linux/fortify-string.h:108:33: error: '__builtin_strncpy' specified bound 128 equals destination size [-Werror=stringop-truncation]
Change it to strscpy_pad(), which produces a properly terminated and
zero-padded string.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/20240313163712.224585-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f23a4d6e07 upstream.
Commit fc663711b9 ("scsi: core: Remove the /proc/scsi/${proc_name}
directory earlier") fixed a bug related to modules loading/unloading, by
adding a call to scsi_proc_hostdir_rm() on scsi_remove_host(). But that led
to a potential duplicate call to the hostdir_rm() routine, since it's also
called from scsi_host_dev_release(). That triggered a regression report,
which was then fixed by commit be03df3d4b ("scsi: core: Fix a procfs host
directory removal regression"). The fix just dropped the hostdir_rm() call
from dev_release().
But it happens that this proc directory is created on scsi_host_alloc(),
and that function "pairs" with scsi_host_dev_release(), while
scsi_remove_host() pairs with scsi_add_host(). In other words, it seems the
reason for removing the proc directory on dev_release() was meant to cover
cases in which a SCSI host structure was allocated, but the call to
scsi_add_host() didn't happen. And that pattern happens to exist in some
error paths, for example.
Syzkaller causes that by using USB raw gadget device, error'ing on
usb-storage driver, at usb_stor_probe2(). By checking that path, we can see
that the BadDevice label leads to a scsi_host_put() after a SCSI host
allocation, but there's no call to scsi_add_host() in such path. That leads
to messages like this in dmesg (and a leak of the SCSI host proc
structure):
usb-storage 4-1:87.51: USB Mass Storage device detected
proc_dir_entry 'scsi/usb-storage' already registered
WARNING: CPU: 1 PID: 3519 at fs/proc/generic.c:377 proc_register+0x347/0x4e0 fs/proc/generic.c:376
The proper fix seems to still call scsi_proc_hostdir_rm() on dev_release(),
but guard that with the state check for SHOST_CREATED; there is even a
comment in scsi_host_dev_release() detailing that: such conditional is
meant for cases where the SCSI host was allocated but there was no calls to
{add,remove}_host(), like the usb-storage case.
This is what we propose here and with that, the error path of usb-storage
does not trigger the warning anymore.
Reported-by: syzbot+c645abf505ed21f931b5@syzkaller.appspotmail.com
Fixes: be03df3d4b ("scsi: core: Fix a procfs host directory removal regression")
Cc: stable@vger.kernel.org
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: John Garry <john.g.garry@oracle.com>
Cc: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@igalia.com>
Link: https://lore.kernel.org/r/20240313113006.2834799-1-gpiccoli@igalia.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c76106cb9 upstream.
Commit 3cc2ffe5c1 ("scsi: sd: Differentiate system and runtime start/stop
management") introduced the manage_system_start_stop scsi_device flag to
allow libata to indicate to the SCSI disk driver that nothing should be
done when resuming a disk on system resume. This change turned the
execution of sd_resume() into a no-op for ATA devices on system
resume. While this solved deadlock issues during device resume, this change
also wrongly removed the execution of opal_unlock_from_suspend(). As a
result, devices with TCG OPAL locking enabled remain locked and
inaccessible after a system resume from sleep.
To fix this issue, introduce the SCSI driver resume method and implement it
with the sd_resume() function calling opal_unlock_from_suspend(). The
former sd_resume() function is renamed to sd_resume_common() and modified
to call the new sd_resume() function. For non-ATA devices, this result in
no functional changes.
In order for libata to explicitly execute sd_resume() when a device is
resumed during system restart, the function scsi_resume_device() is
introduced. libata calls this function from the revalidation work executed
on devie resume, a state that is indicated with the new device flag
ATA_DFLAG_RESUMING. Doing so, locked TCG OPAL enabled devices are unlocked
on resume, allowing normal operation.
Fixes: 3cc2ffe5c1 ("scsi: sd: Differentiate system and runtime start/stop management")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218538
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240319071209.1179257-1-dlemoal@kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81e2c1a0f8 upstream.
The MSM8996 DT doesn't provide frequency limits for the core_clk_unipro
clock, which results in miscalculation of the cycles_in_1us value. Provide
the backwards-compatible default to support existing MSM8996 DT files.
Fixes: b4e13e1ae9 ("scsi: ufs: qcom: Add multiple frequency support for MAX_CORE_CLK_1US_CYCLES")
Cc: Nitin Rawat <quic_nitirawa@quicinc.com>
Cc: stable@vger.kernel.org # 6.7.x
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240218-msm8996-fix-ufs-v3-1-40aab49899a3@linaro.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 051e0840ff upstream.
The dreamcastcard->timer could schedule the spu_dma_work and the
spu_dma_work could also arm the dreamcastcard->timer.
When the snd_pcm_substream is closing, the aica_channel will be
deallocated. But it could still be dereferenced in the worker
thread. The reason is that del_timer() will return directly
regardless of whether the timer handler is running or not and
the worker could be rescheduled in the timer handler. As a result,
the UAF bug will happen. The racy situation is shown below:
(Thread 1) | (Thread 2)
snd_aicapcm_pcm_close() |
... | run_spu_dma() //worker
| mod_timer()
flush_work() |
del_timer() | aica_period_elapsed() //timer
kfree(dreamcastcard->channel) | schedule_work()
| run_spu_dma() //worker
... | dreamcastcard->channel-> //USE
In order to mitigate this bug and other possible corner cases,
call mod_timer() conditionally in run_spu_dma(), then implement
PCM sync_stop op to cancel both the timer and worker. The sync_stop
op will be called from PCM core appropriately when needed.
Fixes: 198de43d75 ("[ALSA] Add ALSA support for the SEGA Dreamcast PCM device")
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Message-ID: <20240326094238.95442-1-duoming@zju.edu.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 457f730825 ]
It's possible the migration file is accessed after reset when it has
been cleaned up, especially when it's initiated by the device. This is
because the driver doesn't rip out the filep when cleaning up it only
frees the related page structures and sets its local struct
pds_vfio_lm_file pointer to NULL. This can cause a NULL pointer
dereference, which is shown in the example below during a restore after
a device initiated reset:
BUG: kernel NULL pointer dereference, address: 000000000000000c
PF: supervisor read access in kernel mode
PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] PREEMPT SMP NOPTI
RIP: 0010:pds_vfio_get_file_page+0x5d/0xf0 [pds_vfio_pci]
[...]
Call Trace:
<TASK>
pds_vfio_restore_write+0xf6/0x160 [pds_vfio_pci]
vfs_write+0xc9/0x3f0
? __fget_light+0xc9/0x110
ksys_write+0xb5/0xf0
__x64_sys_write+0x1a/0x20
do_syscall_64+0x38/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
[...]
Add a disabled flag to the driver's struct pds_vfio_lm_file that gets
set during cleanup. Then make sure to check the flag when the migration
file is accessed via its file_operations. By default this flag will be
false as the memory for struct pds_vfio_lm_file is kzalloc'd, which means
the struct pds_vfio_lm_file is enabled and accessible. Also, since the
file_operations and driver's migration file cleanup happen under the
protection of the same pds_vfio_lm_file.lock, using this flag is thread
safe.
Fixes: 8512ed2563 ("vfio/pds: Always clear the save/restore FDs on reset")
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: Brett Creeley <brett.creeley@amd.com>
Link: https://lore.kernel.org/r/20240308182149.22036-2-brett.creeley@amd.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3651306ae4 ]
The is_psr_su parameter is a boolean flag indicating whether the Panel
Self Refresh Selective Update (PSR SU) feature is enabled which is a
power-saving feature that allows only the updated regions of the screen
to be refreshed, reducing the amount of data that needs to be sent to
the display.
Fixes the below with gcc W=1:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c:5257: warning: Function parameter or member 'is_psr_su' not described in 'fill_dc_dirty_rects'
Fixes: d16df040c8 ("drm/amdgpu: make damage clips support configurable")
Cc: stable@vger.kernel.org
Cc: Hamza Mahfooz <hamza.mahfooz@amd.com>
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc184dbe9f ]
We have observed that there are quite a number of PSR-SU panels on the
market that are unable to keep up with what user space throws at them,
resulting in hangs and random black screens. So, make damage clips
support configurable and disable it by default for PSR-SU displays.
Cc: stable@vger.kernel.org
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a5fd7811a ]
[why]
When populating dml pipes, odm combine policy should be assigned based
on the pipe topology of the context passed in. DML pipes could be
repopulated multiple times during single validate bandwidth attempt. We
need to make sure that whenever we repopulate the dml pipes it is always
aligned with the updated context. There is a case where DML pipes get
repopulated during FPO optimization after ODM combine policy is changed.
Since in the current code we reinitlaize ODM combine policy, even though
the current context has ODM combine enabled, we overwrite it despite the
pipes are already split. This causes DML to think that MPC combine is
used so we mistakenly enable MPC combine because we apply pipe split
with ODM combine policy reset. This issue doesn't impact non windowed
MPO with ODM case because the legacy policy has restricted use cases. We
don't encounter the case where both ODM and FPO optimizations are
enabled together. So we decide to leave it as is because it is about to
be replaced anyway.
Cc: stable@vger.kernel.org # 6.6+
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit cd5432c712 upstream.
In the scenario of entering hibernation with udisk in the system, if the
udisk was gone or resume fail in the thaw phase of hibernation. Its state
will be set to NOTATTACHED. At this point, usb_hub_wq was already freezed
and can't not handle disconnect event. Next, in the poweroff phase of
hibernation, SYNCHRONIZE_CACHE SCSI command will be sent to this udisk
when poweroff this scsi device, which will cause uas_submit_urbs to be
called to submit URB for sense/data/cmd pipe. However, these URBs will
submit fail as device was set to NOTATTACHED state. Then, uas_submit_urbs
will return a value SCSI_MLQUEUE_DEVICE_BUSY to the caller. That will lead
the SCSI layer go into an ugly loop and system fail to go into hibernation.
On the other hand, when we specially check for -ENODEV in function
uas_queuecommand_lck, returning DID_ERROR to SCSI layer will cause device
poweroff fail and system shutdown instead of entering hibernation.
To fix this issue, let uas_submit_urbs to return original generic error
when submitting URB failed. At the same time, we need to translate -ENODEV
to DID_NOT_CONNECT for the SCSI layer.
Suggested-by: Oliver Neukum <oneukum@suse.com>
Cc: stable@vger.kernel.org
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Link: https://lore.kernel.org/r/20240306180814.4897-1-WeitaoWang-oc@zhaoxin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c96319692 upstream.
When auxiliary_device_add() returns error and then calls
auxiliary_device_uninit(), callback function ljca_auxdev_release
calls kfree(auxdev->dev.platform_data) to free the parameter data
of the function ljca_new_client_device. The callers of
ljca_new_client_device shouldn't call kfree() again
in the error handling path to free the platform data.
Fix this by cleaning up the redundant kfree() in all callers and
adding kfree() the passed in platform_data on errors which happen
before auxiliary_device_init() succeeds .
Fixes: acd6199f19 ("usb: Add support for Intel LJCA device")
Cc: stable <stable@kernel.org>
Signed-off-by: Yongzhi Liu <hyperlyzcs@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240311125748.28198-1-hyperlyzcs@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 339f83612f upstream.
wdm_read() cannot race with itself. However, in
service_outstanding_interrupt() it can race with the
workqueue, which can be triggered by error handling.
Hence we need to make sure that the WDM_RESPONDING
flag is not just only set but tested.
Fixes: afba937e54 ("USB: CDC WDM driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20240314115132.3907-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fdada0db0b upstream.
This reverts commit 75fd6485cc.
This patch was applied twice by accident, causing probe failures.
Revert the accident.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Fixes: 75fd6485cc ("usb: phy: generic: Get the vbus supply")
Cc: stable <stable@kernel.org>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20240314092628.1869414-1-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 34a956739d upstream.
E.g. ESMT chips will return an identification code with a length of 5
bytes. In order to prevent ambiguity, flash chips would actually need to
return IDs that are up to 17 or more bytes long due to JEDEC's
continuation scheme. I understand that if a manufacturer ID is located
in bank N of JEDEC's database (there are currently 16 banks), N - 1
continuation codes (7Fh) need to be added to the identification code
(comprising of manufacturer ID and device ID). However, most flash chip
manufacturers don't seem to implement this (correctly).
Signed-off-by: Ezra Buehler <ezra.buehler@husqvarnagroup.com>
Reviewed-by: Martin Kurbanov <mmkurbanov@salutedevices.com>
Tested-by: Martin Kurbanov <mmkurbanov@salutedevices.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240125200108.24374-2-ezra@easyb.ch
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c3366abdbe884be62e5a7502b4db758aa3974c6 upstream.
hci_cmd_sync_cancel_sync shall check the error passed to it since it
will be propagated using req_result which is __u32 it needs to be
properly set to a positive value if it was passed as negative othertise
IS_ERR will not trigger as -(errno) would be converted to a positive
value.
Fixes: 63298d6e75 ("Bluetooth: hci_core: Cancel request on command timeout")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Reported-and-tested-by: Thorsten Leemhuis <linux@leemhuis.info>
Closes: https://lore.kernel.org/all/08275279-7462-4f4a-a0ee-8aa015f829bc@leemhuis.info/
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f10d4a51b upstream.
[Why]
NumFclkLevelsEnabled is used for DcfClocks bounds check
instead of designated NumDcfClkLevelsEnabled.
That can cause array index out-of-bounds access.
[How]
Use designated variable for dcn35 DcfClocks bounds check.
Fixes: a8edc9cc0b ("drm/amd/display: Fix array-index-out-of-bounds in dcn35_clkmgr")
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Sun peng Li <sunpeng.li@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e41d769f1a upstream.
Since commit 0c65dc0626 ("drm/i915/jsl: s/JSL/JASPERLAKE for
platform/subplatform defines"), boot freezes on a Jasper Lake tablet
(Librem 11), usually with graphical corruption on the eDP display,
but sometimes just a black screen. This commit was included in 6.6 and
later.
That commit was intended to refactor EHL and JSL macros, but the change
to ehl_combo_pll_div_frac_wa_needed() started matching JSL incorrectly
when it was only intended to match EHL.
It replaced:
return ((IS_PLATFORM(i915, INTEL_ELKHARTLAKE) &&
IS_JSL_EHL_DISPLAY_STEP(i915, STEP_B0, STEP_FOREVER)) ||
with:
return (((IS_ELKHARTLAKE(i915) || IS_JASPERLAKE(i915)) &&
IS_DISPLAY_STEP(i915, STEP_B0, STEP_FOREVER)) ||
Remove IS_JASPERLAKE() to fix the regression.
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
Cc: stable@vger.kernel.org
Fixes: 0c65dc0626 ("drm/i915/jsl: s/JSL/JASPERLAKE for platform/subplatform defines")
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240313135424.3731410-1-jonathon.hall@puri.sm
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit 1ef4885931)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f12751168f upstream.
Looks like the undelayed vblank gets signalled exactly when
the active period ends. That is a problem for DSB+VRR when
we are already in vblank and expect DSB to start executing
as soon as we send the push. Instead of starting, the DSB
just keeps on waiting for the undelayed vblank which won't
signal until the end of the next frame's active period,
which is far too late.
The end result is that DSB won't have even started
executing by the time the flips/etc. have completed.
We then wait for an extra 1ms, after which we terminate
the DSB and report a timeout:
[drm] *ERROR* [CRTC:80:pipe A] DSB 0 timed out waiting for idle (current head=0xfedf4000, head=0x0, tail=0x1080)
To fix this let's configure DSB to use the so called VRR
"safe window" instead of the undelayed vblank to trigger
the DSB vblank logic, when VRR is enabled.
Cc: stable@vger.kernel.org
Fixes: 34d8311f4a ("drm/i915/dsb: Re-instate DSB for LUT updates")
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/9927
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240306040806.21697-3-ville.syrjala@linux.intel.com
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
(cherry picked from commit 41429d9b68)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 18846627ef upstream.
Reinstate commit 88b065943c ("drm/i915/dsi: Do display on
sequence later on icl+"), for the most part. Turns out some
machines (eg. Chuwi Minibook X) really do need that updated order.
It is also the order the Windows driver uses.
However we can't just undo the revert since that would again
break Lenovo 82TQ. After staring at the VBT sequences for both
machines I've concluded that the Lenovo 82TQ sequences look
somewhat broken:
- INIT_OTP is not present at all
- what should be in INIT_OTP is found in DISPLAY_ON
- what should be in DISPLAY_ON is found in BACKLIGHT_ON
(along with the actual backlight stuff)
The Chuwi Minibook X on the other hand has a full complement
of sequences in its VBT.
So let's try to deal with the broken sequences in the
Lenovo 82TQ VBT by simply swapping the (non-existent)
INIT_OTP sequence with the DISPLAY_ON sequence. Thus we
execute DISPLAY_ON when intending to execute INIT_OTP,
and execute nothing at all when intending to execute
DISPLAY_ON. That should be 100% equivalent to the
revert, for such broken VBTs.
Cc: stable@vger.kernel.org
Fixes: 6992eb815d ("Revert "drm/i915/dsi: Do display on sequence later on icl+"")
References: https://gitlab.freedesktop.org/drm/intel/-/issues/10071
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/10334
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240305083659.8396-1-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit 94ae4612ea)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f7d3b9277f upstream.
Looks like TRANS_CHICKEN bit 31 means something totally different
depending on the platform:
TGL: generate VRR "safe window" for DSB
ADL/DG2: make TRANS_SET_CONTEXT_LATENCY effective with VRR
So far we've only set this on ADL/DG2, but when using DSB+VRR
we also need to set it on TGL.
And a quick test on MTL says it doesn't need this bit for either
of those purposes, even though it's still documented as valid
in bspec.
Cc: stable@vger.kernel.org
Fixes: 34d8311f4a ("drm/i915/dsb: Re-instate DSB for LUT updates")
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/9927
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240306040806.21697-2-ville.syrjala@linux.intel.com
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
(cherry picked from commit 810e4519a1)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0ccc2b30f4 upstream.
[WHY & HOW]
DCN351 and DCN35 should use the same bounding box and IP settings.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Xi Liu <xi.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit edfa93d87f upstream.
[Why]
MPC flow rate control is not needed for DCN30 and above. Current logic
that uses it can result in underflow for certain edge cases (such as
DSC N422 + ODM combine + 422 left edge pixel).
[How]
Remove MPC flow rate control logic and programming for DCN30 and above.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1210e2f103 upstream.
TLB flush after unmap accidentially was removed on
gfx9.4.2. It is to add it back.
Signed-off-by: Eric Huang <jinhuieric.huang@amd.com>
Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a38a829c8 upstream.
The function platform_get_resource was replaced with
devm_platform_ioremap_resource_byname and is called using 0 as name.
This eventually ends up in platform_get_resource_byname in the call
stack, where it causes a null pointer in strcmp.
if (type == resource_type(r) && !strcmp(r->name, name))
It should have been replaced with devm_platform_ioremap_resource.
Fixes: bd69058f50 ("net: ll_temac: Use devm_platform_ioremap_resource_byname()")
Signed-off-by: Claus Hansen Ries <chr@terma.com>
Cc: stable@vger.kernel.org
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/cca18f9c630a41c18487729770b492bb@terma.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 16e87fe23d upstream.
The kcalloc() in nouveau_dmem_evict_chunk() will return null if
the physical memory has run out. As a result, if we dereference
src_pfns, dst_pfns or dma_addrs, the null pointer dereference bugs
will happen.
Moreover, the GPU is going away. If the kcalloc() fails, we could not
evict all pages mapping a chunk. So this patch adds a __GFP_NOFAIL
flag in kcalloc().
Finally, as there is no need to have physically contiguous memory,
this patch switches kcalloc() to kvcalloc() in order to avoid
failing allocations.
CC: <stable@vger.kernel.org> # v6.1
Fixes: 249881232e ("nouveau/dmem: evict device private memory during release")
Suggested-by: Danilo Krummrich <dakr@redhat.com>
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240306050104.11259-1-duoming@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a26de34b3c upstream.
The issue occurs when the devfreq cooling device uses the EM power model
and the get_real_power() callback is provided by the driver.
The EM power table is sorted ascending，can't index the table by cooling
device state，so convert cooling state to performance state by
dfc->max_state - dfc->capped_state.
Fixes: 615510fe13 ("thermal: devfreq_cooling: remove old power model and use EM")
Cc: 5.11+ <stable@vger.kernel.org> # 5.11+
Signed-off-by: Ye Zhang <ye.zhang@rock-chips.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 55251fbdf0 upstream.
This reverts commit 748dc0b65e.
Partial zone append completions cannot be supported as there is no
guarantees that the fragmented data will be written sequentially in the
same manner as with a full command. Commit 748dc0b65e ("block: fix
partial zone append completion handling in req_bio_endio()") changed
req_bio_endio() to always advance a partially failed BIO by its full
length, but this can lead to incorrect accounting. So revert this
change and let low level device drivers handle this case by always
failing completely zone append operations. With this revert, users will
still see an IO error for a partially completed zone append BIO.
Fixes: 748dc0b65e ("block: fix partial zone append completion handling in req_bio_endio()")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240328004409.594888-2-dlemoal@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9e2a5b00a upstream.
"PM runtime functions" was been added in sdhci-omap driver in commit
f433e8aac6 ("mmc: sdhci-omap: Implement PM runtime functions") along
with "card power off and enable aggressive PM" in commit 3edf588e7f
("mmc: sdhci-omap: Allow SDIO card power off and enable aggressive PM").
Since then, the sdhci-omap driver doesn't work using mmc-hs200 mode
due to the tuning values being lost during a pm transition.
As for the sdhci_am654 driver, request a new tuning sequence before
suspend (sdhci_omap_runtime_suspend()), otherwise the device will
trigger cache flush error:
mmc1: cache flush error -110 (ETIMEDOUT)
mmc1: error -110 doing aggressive suspend
followed by I/O errors produced by fdisk -l /dev/mmcblk1boot1:
I/O error, dev mmcblk1boot0, sector 64384 op 0x0:(READ) flags 0x80700 phys_seg 1
prio class 2
I/O error, dev mmcblk1boot1, sector 64384 op 0x0:(READ) flags 0x80700 phys_seg 1
prio class 2
I/O error, dev mmcblk1boot1, sector 64384 op 0x0:(READ) flags 0x0 phys_seg 1
prio class 2
Buffer I/O error on dev mmcblk1boot1, logical block 8048, async page read
I/O error, dev mmcblk1boot0, sector 64384 op 0x0:(READ) flags 0x0 phys_seg 1
prio class 2
Buffer I/O error on dev mmcblk1boot0, logical block 8048, async page read
Don't re-tune if auto retuning is supported in HW (when SDHCI_TUNING_MODE_3
is available).
Link: https://lore.kernel.org/all/2e5f1997-564c-44e4-b357-6343e0dae7ab@smile.fr
Fixes: f433e8aac6 ("mmc: sdhci-omap: Implement PM runtime functions")
Signed-off-by: Romain Naour <romain.naour@skf.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240315234444.816978-1-romain.naour@smile.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c864371b2 upstream.
Following issue was observed while running the uffd-unit-tests selftest
on ARM devices. On x86_64 no issues were detected:
pthread_create followed by fork caused deadlock in certain cases wherein
fork required some work to be completed by the created thread. Used
synchronization to ensure that created thread's start function has started
before invoking fork.
[edliaw@google.com: refactored to use atomic_bool]
Link: https://lkml.kernel.org/r/20240325194100.775052-1-edliaw@google.com
Fixes: 760aee0b71 ("selftests/mm: add tests for RO pinning vs fork()")
Signed-off-by: Lokesh Gidra <lokeshgidra@google.com>
Signed-off-by: Edward Liaw <edliaw@google.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 105840ebd7 upstream.
The sigbus-wp test requires the UFFD_FEATURE_WP_HUGETLBFS_SHMEM flag for
shmem and hugetlb targets. Otherwise it is not backwards compatible with
kernels <5.19 and fails with EINVAL.
Link: https://lkml.kernel.org/r/20240321232023.2064975-1-edliaw@google.com
Fixes: 73c1ea939b ("selftests/mm: move uffd sig/events tests into uffd unit tests")
Signed-off-by: Edward Liaw <edliaw@google.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Peter Xu <peterx@redhat.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
