Don't populate the arrays on the stack, instead make them static.
Makes the object code smaller by 135 bytes:
Before:
text data bss dec hex filename
15135 4240 128 19503 4c2f inv_mpu_core.o
After:
text data bss dec hex filename
14840 4400 128 19368 4ba8 inv_mpu_core.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
As user's guide "ADS1015EVM, ADS1115EVM, ADS1015EVM-PDK, ADS1115EVM-PDK
User Guide (Rev. B)" (http://www.ti.com/lit/ug/sbau157b/sbau157b.pdf)
states at page 16:
"Note that both the ADS1115 and ADS1015 have internal clocks with a ±10%
accuracy. If performing FFT tests, frequencies may appear to be incorrect
as a result of this tolerance range.", add those 10% to converion wait
time.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is no point writing ADS1015_CFG_REG when configuration
didn't change. Avoid that.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add missing break statement to prevent the code for case
IIO_CHAN_INFO_CALIBBIAS falling through to the default case.
Also, add a break to the default case for the switch within
case IIO_CHAN_INFO_CALIBBIAS.
Addresses-Coverity-ID: 1357377
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Check return values from call to devm_kzalloc() and devm_kmemup()
in order to prevent a NULL pointer dereference.
This issue was detected using Coccinelle and the following semantic patch:
@@
expression x;
identifier fld;
@@
* x = devm_kzalloc(...);
... when != x == NULL
x->fld
Fixes: 7ba9df54b0 ("iio: multiplexer: new iio category and iio-mux driver")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The TCS3472 device provides interrupt signal for out-of-threshold events
with persistence filter.
This change adds interrupt support for the threshold events and enables
to configure the period of time by persistence filter.
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The SPI core has handled this for some time.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
This has been handled by the spi core for some time.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
This has been handled by the spi core for some time now.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This has been handled by the i2c core for some time.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
This is now done through some macro magic by the core.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Peter Rosin <peda@axentia.se>
Data-ready line in LIS3MDL is routed to drdy pin and it is not possible
to select a different INT pin. st_sensors_set_dataready_irq() assumes
that if drdy int address is not exported in register map, irq trigger
is not supported by the sensor and hw_irq_trigger is always false.
Based on this configuration st_sensors_irq_thread does not consume
generated interrupt causing an unhandled irq.
Fix this taking into account status register address in
st_sensors_set_dataready_irq()
Fixes: 90efe05562 (iio: st_sensors: harden interrupt handling)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The comparator polarity field in config register is not correctly
initialized as per the interrupt trigger setting. Because the bitfield
definision is wrong and bit shifting is missed.
Fixes: d9f39babd8 ("iio: adc: ti-ads1015: add threshold event support")
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements will shortly go away.
Note that stm32-timer-trigger has expanded rather beyond triggers
(to include encoder input counting for example) and hence has an
iio_info structure.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The equivalent of this is now done via macro magic when
the relevant register call is made. The actual structure
elements will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The equivalent of this is now done via macro magic when
the relevant register call is made. The actual structure
elements will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The equivalent of this is now done via macro magic when
the relevant register call is made. The actual structure
elements will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The equivalent is now done via macro magic when
the relevant register call is made. The actual structure
element will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The equivalent is now done via macro magic when
the relevant register call is made. The actual structure
element will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The equivalent of this is now done via macro magic when
the relevant register call is made. The actual structure
element will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The equivalent is now done via macro magic when
the relevant register calls are made. The actual structure
elements will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements will shortly go away.
Clearly this set jumps across multiple areas, but inherently it
can't be grouped like the other sets in this series so I've done
all the stuff in the common directory together.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
There are a few cases where none of the callbacks are supplied and the
ops structure purely existed to provide the driver module.
Given that is done differently now, we don't need to have a trig_ops structure.
Allow for it not being there required a few additional sanity checks when
trying check if particular callbacks are set.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
This trig_ops.owner assignment occurs in all trigger drivers and
can be simply automated using a macro as has been done in many
other places in the kernel.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Starting point in boiler plate reduction similar to that done for
many similar cases elsewhere in the kernel.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
New device support:
* ak8974
- support the AMI306.
* st_magnetometer
- add support for the LIS2MDL with bindings.
* rockchip-saradc
- add binding for rv1108 SoC (no driver change).
* srf08
- add srf02 (i2c only) and srf10 support.
* stm32-timer
- support for the STM32H7 to existing driver.
Features:
* tools
- move over to the tools buildsystem rather than hand rolling.
- add an install section to the build.
* ak8974
- use serial number to add device randomness.
- add AMI306 calibration data output.
* ccs811
- triggered buffer support.
* srf08
- add a device tree table as the old style i2c probing is going away,
- add triggered buffer support
* st32-adc
- add optional st,min-sample-time-nsecs binding to allow control of
sampling against analog circuitry.
* stm32-timer
- add output compare triggers.
* ti-ads1015
- add threshold event support.
* ti-ads7950
- Allow use on ACPI platforms including providing a default reference
voltage as there is no way to obtain this on ACPI currently.
Cleanup and fixes:
* ad7606
- fix an error return code in probe.
* ads1015
- fix incorrect data rate setting update when capture in progress,
- fix wrong scale information for the ADS1115,
- make conversions work when CONFIG_PM is not set,
- make sure we don't get a stale result after a runtime resume by
ensuring we wait long enough,
- avoid returning a false error form the buffer setup callbacks,
- add enough wait time to get the correct conversion,
- remove an unnecessary config register update,
- add a helper to set conversion mode reducing repeated boilerplate,
- use devm_iio_triggered_buffer_setup to simplify error and remove
paths,
- use iio_device_claim_direct_mode instead of opencoding the same.
* ak8974
- mark the INT_CLEAR register as precious to prevent debugfs access.
* apds9300
- constify the i2c_device_id.
* at91-sama5 adc
- add missing Kconfig dependency.
* bma180 accel
- constify the i2c_device_id.
* rockchip_saradc
- explicitly request exclusive reset control as part of the reset rework
on going throughout the kernel.
* st_accel
- fix drdy configuration for a load of accelerometers that only have
the int1 line. Fix is unimportant as presumably no deviec tree actually
used the non existent hardware line.
* st_pressure
- fix drdy configuration for LPS22HB and LPS25H by dropping int2 support
as they don't have this. Fix is unimportant as presumably no device tree
actually used the non existent hardware line.
* stm32-dac
- explicitly request exclusive reset control (part of reset being reworked).
* tsl2583
- constify the i2c_device_id.
* xadc
- coding style fixes.
-----BEGIN PGP SIGNATURE-----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=b6g8
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.14b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of IIO new device support, features and cleanup for the 4.14 cycle.
New device support:
* ak8974
- support the AMI306.
* st_magnetometer
- add support for the LIS2MDL with bindings.
* rockchip-saradc
- add binding for rv1108 SoC (no driver change).
* srf08
- add srf02 (i2c only) and srf10 support.
* stm32-timer
- support for the STM32H7 to existing driver.
Features:
* tools
- move over to the tools buildsystem rather than hand rolling.
- add an install section to the build.
* ak8974
- use serial number to add device randomness.
- add AMI306 calibration data output.
* ccs811
- triggered buffer support.
* srf08
- add a device tree table as the old style i2c probing is going away,
- add triggered buffer support
* st32-adc
- add optional st,min-sample-time-nsecs binding to allow control of
sampling against analog circuitry.
* stm32-timer
- add output compare triggers.
* ti-ads1015
- add threshold event support.
* ti-ads7950
- Allow use on ACPI platforms including providing a default reference
voltage as there is no way to obtain this on ACPI currently.
Cleanup and fixes:
* ad7606
- fix an error return code in probe.
* ads1015
- fix incorrect data rate setting update when capture in progress,
- fix wrong scale information for the ADS1115,
- make conversions work when CONFIG_PM is not set,
- make sure we don't get a stale result after a runtime resume by
ensuring we wait long enough,
- avoid returning a false error form the buffer setup callbacks,
- add enough wait time to get the correct conversion,
- remove an unnecessary config register update,
- add a helper to set conversion mode reducing repeated boilerplate,
- use devm_iio_triggered_buffer_setup to simplify error and remove
paths,
- use iio_device_claim_direct_mode instead of opencoding the same.
* ak8974
- mark the INT_CLEAR register as precious to prevent debugfs access.
* apds9300
- constify the i2c_device_id.
* at91-sama5 adc
- add missing Kconfig dependency.
* bma180 accel
- constify the i2c_device_id.
* rockchip_saradc
- explicitly request exclusive reset control as part of the reset rework
on going throughout the kernel.
* st_accel
- fix drdy configuration for a load of accelerometers that only have
the int1 line. Fix is unimportant as presumably no deviec tree actually
used the non existent hardware line.
* st_pressure
- fix drdy configuration for LPS22HB and LPS25H by dropping int2 support
as they don't have this. Fix is unimportant as presumably no device tree
actually used the non existent hardware line.
* stm32-dac
- explicitly request exclusive reset control (part of reset being reworked).
* tsl2583
- constify the i2c_device_id.
* xadc
- coding style fixes.
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-iio@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADS1015 device provides programmable comparator that can issue an
interrupt on the ALERT pin. This change adds the iio threshold event
support for that feature.
The ADS1015 device only have a single config register which contains an
input multiplexer selection, comparator settings, and etc. So only a
single event channel can be enabled at a time. Also enabling both buffer
and event are prohibited for simplicity.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
While the iio buffer for the ti-ads1015 driver is enabled, reading the
raw ADC channel data is restricted. We usually use the
iio_device_claim_direct_mode()/iio_device_release_direct_mode() pair for
that.
This change consequently reverses the locking order for the driver's
private lock and indio_dev->mlock which acquired by
iio_device_claim_direct_mode() internally. But it's safe because there is
no other dependency between these locks.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use devm_iio_triggered_buffer_setup to simplify the error path in the
probe() and remove() function.
This changes the remove order, but the end result of remove function
actually does the reverse of probe.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This adds a helper function to set conversion mode as there are a fair
number of users.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ti-ads1015 driver has eight iio voltage channels and each iio channel
can hold own scale information.
The ADS1015 device only have a single config register which contains an
input multiplexer selection, PGA and data rate settings. So the driver
should load the correct settings when the input multiplexer selection is
changed.
However, regardless of which channlel is currently selected, changing any
iio channel's scale information immediately overwrites the current PGA
setting in the config register.
It is harmless because the correct PGA settings are reloaded just before
getting adc result anyway. But it is unnecessary register update and
should be removed.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver assumes that the device is operating in the continuous
conversion mode which performs the conversion continuously. So this driver
inserts a wait time before reading the conversion register if the
configuration is changed from a previous request.
Currently, the wait time is only the period required for a single
conversion that is calculated as the reciprocal of the sampling frequency.
However we also need to wait for the the previous conversion to complete.
Otherwise we probably get the conversion result for the previous
configuration when the sampling frequency is lower.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
pm_runtime_get_sync() and pm_runtime_put_autosuspend() return 0 on
success, 1 if the device's runtime PM status was already requested status
or error code on failure. So a positive return value doesn't indicate an
error condition.
However, any non-zero return values from buffer preenable and postdisable
callbacks are recognized as an error and this driver reuses the return
value from pm_runtime_get_sync() and pm_runtime_put_autosuspend() in
these callbacks. This change fixes the false error detections.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver assumes that the device is operating in the continuous
conversion mode which performs the conversion continuously. So this driver
doesn't insert a wait time before reading the conversion register if the
configuration is not changed from a previous request.
This assumption is broken if the device is runtime suspended and entered
a power-down state. The forthcoming request causes reading a stale result
from the conversion register as the device is runtime resumed just before.
Fix it by adding a flag to detect that condition and insert a necessary
wait time.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADS1015 device have two operating modes, continuous conversion mode
and single-shot mode. This driver assumes that the continuous conversion
mode is selected by runtime resume callback when the ADC result is
requested.
If CONFIG_PM is disabled, the device is always in the default single-shot
mode and no one begins a single conversion. So the conversion register
doesn't contain valid ADC result. Fix it by changing the continuous mode
in probe function.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ti-ads1015 driver supports ADS1015 and ADS1115 devices. The same
scale information is used for both devices in this driver, however they
have actually different values and the ADS1115's one is not correct.
These devices have the same full-scale input voltage range for each PGA
selection. So instead of adding another hardcoded scale information,
compute a correct scale on demand from each device's resolution.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ti-ads1015 driver has eight iio voltage channels and each iio channel
can hold own sampling frequency information.
The ADS1015 device only have a single config register which contains an
input multiplexer selection, PGA and data rate settings. So the driver
should load the correct settings when the input multiplexer selection is
changed.
However, regardless of which channlel is currently selected, changing any
iio channel's sampling frequency information immediately overwrites the
current data rate setting in the config register.
It breaks the current data rate setting if the different channel's sampling
frequency information is changed because the data rate setting is not
reloaded when the input multiplexer is switched.
This removes the unexpected config register update and correctly load the
data rate setting before getting adc result.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
ACPI enabled platforms do not have a mean of regulators. Instead we use
hard coded voltage value for reference pin. When value is 0 (default) we
fall back to request a regulator.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use AMI306 calibration data for randomness and debugging.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove IRQ active low support for LSM303AGR since the sensor does not
support that capability for data-ready line
Fixes: a9fd053b56 (iio: st_sensors: support active-low interrupts)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It has been reported for a while that with iio-sensor-proxy service the
rotation only works after one suspend/resume cycle. This required a wait
in the systemd unit file to avoid race. I found a Yoga 900 where I could
reproduce this.
The problem scenerio is:
- During sensor driver init, enable run time PM and also set a
auto-suspend for 3 seconds.
This result in one runtime resume. But there is a check to avoid
a powerup in this sequence, but rpm is active
- User space iio-sensor-proxy tries to power up the sensor. Since rpm is
active it will simply return. But sensors were not actually
powered up in the prior sequence, so actaully the sensors will not work
- After 3 seconds the auto suspend kicks
If we add a wait in systemd service file to fire iio-sensor-proxy after
3 seconds, then now everything will work as the runtime resume will
actually powerup the sensor as this is a user request.
To avoid this:
- Remove the check to match user requested state, this will cause a
brief powerup, but if the iio-sensor-proxy starts immediately it will
still work as the sensors are ON.
- Also move the autosuspend delay to place when user requested turn off
of sensors, like after user finished raw read or buffer disable
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix reading trigger mode, when other bit-fields are set. SMCR register
value must be masked to read SMS (slave mode selection) only.
Fixes: 9eba381 ("iio: make stm32 trigger driver use
INDIO_HARDWARE_TRIGGERED mode")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
According to the datasheet, the range of the acceleration is [-10 g, + 10 g],
so the scale factor should be 10 instead of 5.
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reading INT_CLEAR has side effects - disallow reading it via debugfs.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Mix device-specific data into randomness pool.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for AMI306 magnetometer - very similar to AMI305.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
A software trigger such as hrtimer can be used to capture the data
that will be stored in the buffer.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: Alison Schofield <amsfield22@gmail.com>
Signed-off-by: Narcisa Ana Maria Vasile <narcisaanamaria12@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
srf02 added with support for i2c interface
Attributes for setting max range or sensitivity are omitted for the case of
srf02 type sensor, because they are not supported by the hardware.
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Ultrasonic sensor srf10 is quite similar to srf08 and now also supported by
the driver as device tree compatible string.
It was necessary to prepare the source for supplementary sensors. This is
done by enum srf08_sensor_type.
The most significiant difference between srf08 and srf10 is another range
and values of register gain (in the driver it's call sensitivity).
Therefore the array of it is extended and dependent of the sensor type.
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for triggered buffers.
Data format is quite simple:
distance 16 Bit
alignment 48 Bit
timestamp 64 Bit
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Added MODULE_DEVICE_TABLE for device tree bindings.
It used to work without it by using the i2c_device_id table, but adding the
table makes everything clear and documented.
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
add support to STMicroelectronics LIS2MDL magnetometer in
st_magn framework
http://www.st.com/resource/en/datasheet/lis2mdl.pdf
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Without the triggered buffer code, we get a link error:
drivers/iio/adc/at91-sama5d2_adc.o: In function `at91_adc_probe':
at91-sama5d2_adc.c:(.text+0x938): undefined reference to `devm_iio_triggered_buffer_setup'
This adds a Kconfig 'select' statement like other ADC
drivers have it already.
Fixes: 5e1a1da0f8 ("iio: adc: at91-sama5d2_adc: add hw trigger and buffer support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove int2 configuration parameter for LIS3DH, LSM303DLHC, LSM330D,
LSM330DL, LSM330DLC, LSM303AGR, LIS2DH12 and LNG2DM since these devices
export just int1 as data-ready line
Fixes: 23cde4d65c (iio: Added platform data to select the DRDY pin)
Fixes: dcdb0a78ca (iio: accel: st_accel: add support to lng2dm)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove int2 configuration parameter for LPS22HB and LPS25H since
these devices export just int1 as data-ready line
Fixes: 931878405b (iio:pressure: Add support for LPS25H pressure sensor)
Fixes: e039e2f5b4 (iio:st_pressure:initial lps22hb sensor support)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch fix following checkpatch warnings in xadc driver
1. prefer 'unsigned int' to bare use of 'unsigned'.
2. else is not generally useful after a break or return.
3. fill all function definition arguments with identifier name
Signed-off-by: Sai Krishna Potthuri <lakshmis@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add output compare trigger sources available on some instances.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for STM32H7 timer triggers:
- Add new valids_table
- Introduce compatible, with configuration data
- Extend up to 15 timers, available on STM32H7
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In the reference HID sensor hub firmware all Named array enums were
0-based. There is no description of the default base of enums in HID
sensor hub specification as logical minimum should have set this base
value.
Every sensor hub implemented enum as 1-based, without explicitly setting
logical minimum to 1, because of the implementation by one of the major
OS vendor. In Linux we used logical minimum to decide the enum base.
Some sensor hub FWs already changed logical minimum from 0 to 1. We hoped
that every other vendor will follow. But that didn't happen and we had to
fix the report header for every sensor hub to change logical minimum to 1
by using .report_fixup() callback. So for every new sensor hub we had to
modify source code by adding this quirk based on the vendor and device id.
This is becoming a maintenance burden.
This patch hardcodes the logical minimum of power and report state
attributes to 1. In this way we can remove the existing quirks and also
we don't have to add more quirks.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
SPI device registered via OF will always match a legacy SPI device ID and
that the MODALIAS reported will always be of the form spi:<device>.
There is an ACPI method to enumerate such devices via specific ACPI ID
and use of compatible strings. It will not work for the drivers which
have no OF match ID table present.
Besides this could change in the future so the correct approach is to
have an OF device ID table if the devices are registered via OF.
Tested-by: David Lechner <david@lechnology.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
STM32 ADC allows each channel to be sampled with a different sampling time,
by setting SMPR registers. Basically, value depends on local electrical
properties. Selecting correct value for sampling time highly depends on
analog source impedance. There is a manual that may help in this process:
'How to get the best ADC accuracy in STM32...'
This patch allows to configure minimum sampling time via device tree,
either for:
- all channels at once:
st,min-sample-time-nsecs = <10000>;
- independently for each channel (must match "st,adc-channels" list):
st,adc-channels = <0 1>;
st,min-sample-time-nsecs = <5000 10000>;
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
ADC clock input is provided to internal prescaler (that decreases its
frequency). It's then used as reference clock for conversions.
- Fix common clock rate used then by stm32-adc sub-devices. Take common
prescaler into account. Currently, rate is used to set "boost" mode.
It may unnecessarily be set. This impacts power consumption.
- Fix ADC max clock rate on STM32H7 (fADC from datasheet). Currently,
prescaler may be set too low. This can result in ADC reference
clock used for conversion to exceed max allowed clock frequency.
Fixes: 95e339b6e8 ("iio: adc: stm32: add support for STM32H7")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Proper support for the INA219 lowered the minimum sampling period from
2*140us to 2*84us. Subtracting 200us later leads to an underflow and
an almost infinite udelay later.
Using a signed int for the sampling period provides sufficient range
(at most 2*8640*1024us), but catches the underflow when comparing with
buffer_us.
Fixes: 18edac2e22 ("iio: adc: Fix integration time/averaging for INA219/220")
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In order to use encoder mode, timers needs to be enabled (e.g. CEN bit)
along with peripheral clock.
Add IIO_CHAN_INFO_ENABLE attribute to handle this.
Also, in triggered mode, CEN bit is set automatically in hardware.
Then clock must be enabled before starting triggered mode.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fixes: 4adec7da05 ("iio: stm32 trigger: Add quadrature encoder device")
This fixes two issues:
- stm32_set_count_direction: to set down direction
- stm32_get_count_direction: to get down direction
IIO core provides/expects value to be an index of iio_enum items array.
This needs to be turned by these routines into TIM_CR1_DIR (e.g. BIT(4))
value.
Also, report error when attempting to write direction, when in encoder
mode: in this case, direction is read only (given by encoder inputs).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fixes: 4adec7da05 ("iio: stm32 trigger: Add quadrature encoder device")
IIO core expects zero as return value for write_raw() callback
in case of success.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
If the device is not initialized at least once it happens that the humidity
reading is skipped, which means the special value 0x8000 is delivered.
For omitting this case the oversampling of the humidity must be set before
the oversampling of the temperature und pressure is set as written in the
datasheet of the BME280.
Furthermore proper error detection is added in case a skipped value is read
from the device. This is done also for pressure and temperature reading.
Especially it don't make sense to compensate this value and treat it as
regular value.
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
4 completely new drivers in this set and plenty of other stuff.
One ABI change due to a silly mistake a long time back. Hopefully no
one will notice. It effects the numerical order of consumer device
channels which was the reverse of the obvious. It's going the slow
way to allow us some margin to spot if we have broken userspace or
not (seems unlikely)
New Device Support
* ccs811
- new driver for the Volatile Organic Compounds (VOC) sensor.
* dln2 adc
- new driver for the ADC on this flexible usb board.
* EP93xx
- new driver for this Cirrus logic SoC ADC.
* ltc2471
- new ADC driver support the ltc2471 and ltc2473
* st_accel
- add trivial table entries to support H3LIS331DL, LIS331DL, LIS3LV02DL.
* st_gyro
- add L3GD20H support (again) having fixed the various things that were
broken in the first try. Includes devicetree binding.
* stm32 dac
- add support for the DACs in the STM32F4 series
Features
* Documentation
- add missing power attribute documentation to the ABI docs.
* at91-sama5d2
- add hardware trigger and buffered capture support with bindings.
- suspend and resume functionality.
* bmc150
- support for the BOSC0200 ACPI device id seen on some tablets.
* hdc100x
- devicetree bindings
- document supported devices
- match table and device ids.
* hts221
- support active low interrupts (with bindings)
- open drain mode with bindings.
* htu21
- OF match table and bindings.
* lsm6dsx
- open drain mode with bindings
* ltc2497
- add support for board file based consumer mapping.
* ms5367
- OF match table and bindings.
* mt7622
- binding document and OF match table.
- suspend and resume support.
* rpr0521
- triggered buffer support.
* tsys01
- OF match table and bindings.
Cleanups and minor fixes
* core
- fix ordering of IIO channels to entry numbers when using
iio_map_array_register rather than reversing them.
- use the new %pOF format specifier rather than full name for the
device tree nodes.
* ad7280a
- fix potential issue with macro argument reuse.
* ad7766
- drop a pointless NULL value check as it's done in the gpiod code.
* adis16400
- unsigned -> unsigned int.
* at91 adc
- make some init data static to reduce code size.
* at91-sama5d2 ADC
- make some init data static to reduce code size.
* da311
- make some init data static to reduce code size.
* hid-sensor-rotation
- drop an unnecessary static.
* hts221
- refactor the write_with_mask code.
- move the BDU configuration to probe time as there is no reason for it
to change.
- avoid overwriting reserved data during power-down. This is a fix, but
the infrastructure need was too invasive to send it to mainline except
in a merge window. It's not a regression as it was always wrong.
- avoid reconfigure the sampling frequency multiple times by just
doing it in the write_raw function directly.
- refactor the power_on/off calls into a set_enable.
- move the dry-enable logic into trig_set_state as that is the only
place it was used.
* ina219
- fix polling of ina226 conversion ready flag.
* imx7d
- add vendor name in kconfig for consistency with similar parts.
* mcp3422
- Change initial channel to 0 as it feels more logical.
- Check for some errors in probe.
* meson-saradc
- add a check of of_match_device return value.
* mpu3050
- allow open drain for any interrupt type.
* rockchip adc
- add check on of_match_device return value.
* sca3000
- drop a trailing whitespace.
* stm32 adc
- make array stm32h7_adc_ckmodes_spec static.
* stm32 dac
- fix an error message.
* stm32 timers
- fix clock name in docs to match reality after changes.
* st_accel
- explicit OF table (spi).
- add missing entries to OF table (i2c).
- rename of_device_id table to drop the part name.
- adding missing lis3l02dq entry to bindings.
- rename H3LIS331DL_DRIVER_NAME to line up with similar entries in driver.
* st_gyro
- explicit OF table (spi).
* st_magn
- explicit OF table (spi).
- enable multiread for lis3mdl.
* st_pressure
- explicit OF table (spi).
* st_sensors common.
- move st_sensors_of_i2c_probe and rename to make it available for spi
drivers.
* tsc3472
- don't write an extra byte when writing the ATIME register.
- add a link to the datasheet.
* tsl2x7x - continued staging cleanups
- add of_match_table.
- drop redundant power_state sysfs attribute.
- drop wrapper tsl2x7x_i2c_read.
- clean up i2c calls made in tsl2x7x_als_calibrate.
- refactor the read and write _event_value callbacks to handle additional
elements.
- use usleep_range instead of mdelay.
- check return value from tsl2x7x_invoke_change.
* zpa2326
- add some newline to the end of logging macros.
-----BEGIN PGP SIGNATURE-----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=imPz
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.14a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of IIO new device support, features and cleanups for the 4.14 cycle.
4 completely new drivers in this set and plenty of other stuff.
One ABI change due to a silly mistake a long time back. Hopefully no
one will notice. It effects the numerical order of consumer device
channels which was the reverse of the obvious. It's going the slow
way to allow us some margin to spot if we have broken userspace or
not (seems unlikely)
New Device Support
* ccs811
- new driver for the Volatile Organic Compounds (VOC) sensor.
* dln2 adc
- new driver for the ADC on this flexible usb board.
* EP93xx
- new driver for this Cirrus logic SoC ADC.
* ltc2471
- new ADC driver support the ltc2471 and ltc2473
* st_accel
- add trivial table entries to support H3LIS331DL, LIS331DL, LIS3LV02DL.
* st_gyro
- add L3GD20H support (again) having fixed the various things that were
broken in the first try. Includes devicetree binding.
* stm32 dac
- add support for the DACs in the STM32F4 series
Features
* Documentation
- add missing power attribute documentation to the ABI docs.
* at91-sama5d2
- add hardware trigger and buffered capture support with bindings.
- suspend and resume functionality.
* bmc150
- support for the BOSC0200 ACPI device id seen on some tablets.
* hdc100x
- devicetree bindings
- document supported devices
- match table and device ids.
* hts221
- support active low interrupts (with bindings)
- open drain mode with bindings.
* htu21
- OF match table and bindings.
* lsm6dsx
- open drain mode with bindings
* ltc2497
- add support for board file based consumer mapping.
* ms5367
- OF match table and bindings.
* mt7622
- binding document and OF match table.
- suspend and resume support.
* rpr0521
- triggered buffer support.
* tsys01
- OF match table and bindings.
Cleanups and minor fixes
* core
- fix ordering of IIO channels to entry numbers when using
iio_map_array_register rather than reversing them.
- use the new %pOF format specifier rather than full name for the
device tree nodes.
* ad7280a
- fix potential issue with macro argument reuse.
* ad7766
- drop a pointless NULL value check as it's done in the gpiod code.
* adis16400
- unsigned -> unsigned int.
* at91 adc
- make some init data static to reduce code size.
* at91-sama5d2 ADC
- make some init data static to reduce code size.
* da311
- make some init data static to reduce code size.
* hid-sensor-rotation
- drop an unnecessary static.
* hts221
- refactor the write_with_mask code.
- move the BDU configuration to probe time as there is no reason for it
to change.
- avoid overwriting reserved data during power-down. This is a fix, but
the infrastructure need was too invasive to send it to mainline except
in a merge window. It's not a regression as it was always wrong.
- avoid reconfigure the sampling frequency multiple times by just
doing it in the write_raw function directly.
- refactor the power_on/off calls into a set_enable.
- move the dry-enable logic into trig_set_state as that is the only
place it was used.
* ina219
- fix polling of ina226 conversion ready flag.
* imx7d
- add vendor name in kconfig for consistency with similar parts.
* mcp3422
- Change initial channel to 0 as it feels more logical.
- Check for some errors in probe.
* meson-saradc
- add a check of of_match_device return value.
* mpu3050
- allow open drain for any interrupt type.
* rockchip adc
- add check on of_match_device return value.
* sca3000
- drop a trailing whitespace.
* stm32 adc
- make array stm32h7_adc_ckmodes_spec static.
* stm32 dac
- fix an error message.
* stm32 timers
- fix clock name in docs to match reality after changes.
* st_accel
- explicit OF table (spi).
- add missing entries to OF table (i2c).
- rename of_device_id table to drop the part name.
- adding missing lis3l02dq entry to bindings.
- rename H3LIS331DL_DRIVER_NAME to line up with similar entries in driver.
* st_gyro
- explicit OF table (spi).
* st_magn
- explicit OF table (spi).
- enable multiread for lis3mdl.
* st_pressure
- explicit OF table (spi).
* st_sensors common.
- move st_sensors_of_i2c_probe and rename to make it available for spi
drivers.
* tsc3472
- don't write an extra byte when writing the ATIME register.
- add a link to the datasheet.
* tsl2x7x - continued staging cleanups
- add of_match_table.
- drop redundant power_state sysfs attribute.
- drop wrapper tsl2x7x_i2c_read.
- clean up i2c calls made in tsl2x7x_als_calibrate.
- refactor the read and write _event_value callbacks to handle additional
elements.
- use usleep_range instead of mdelay.
- check return value from tsl2x7x_invoke_change.
* zpa2326
- add some newline to the end of logging macros.
Move data-ready configuration in hts221_buffer.c since it is only related
to trigger logic
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add open drain support in order to share requested IRQ line between
hts221 device and other peripherals
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
New driver adding support for ADC found on Cirrus Logic EP93xx series of SoCs.
Board specific code must take care to create plaform device with all necessary
resources.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
* ad2s1210
- Fix negative angular velocity reads (identified by a gcc 7 warning)
* aspeed-adc
- Wait for initialization sequence to finish before enabling channels.
Without it no channels work.
* axp288
- Revert a patch that dropped some bogus register mods. No one is entirely
sure why but it breaks charging on some devices.
- Fix GPADC pin read returning 0. Turns out a small sleep is needed.
* bmc150
- Make sure device is restored to normal state after suspend / resume
cycle. Otherwise, simple sysfs reads are broken.
* tsl2563
- fix wrong event code.
* st-accel
- add spi 3-wire support. Needed to fix the lsm303agr accelerometer
which only had 3 wires in all cases. Side effect is to enable optional
3-wire support for other devices.
* st-pressure
- disable multiread by default for LPS22HB (only effects SPI)
* sun4i-gpadc-iio
- fix unbalanced irq enable / disable
* vf610
- Fix VALT slection for REFSEL bits - ensures we are using the
right reference pins.
-----BEGIN PGP SIGNATURE-----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=BApO
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.13a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 4.13 cycle.
* ad2s1210
- Fix negative angular velocity reads (identified by a gcc 7 warning)
* aspeed-adc
- Wait for initialization sequence to finish before enabling channels.
Without it no channels work.
* axp288
- Revert a patch that dropped some bogus register mods. No one is entirely
sure why but it breaks charging on some devices.
- Fix GPADC pin read returning 0. Turns out a small sleep is needed.
* bmc150
- Make sure device is restored to normal state after suspend / resume
cycle. Otherwise, simple sysfs reads are broken.
* tsl2563
- fix wrong event code.
* st-accel
- add spi 3-wire support. Needed to fix the lsm303agr accelerometer
which only had 3 wires in all cases. Side effect is to enable optional
3-wire support for other devices.
* st-pressure
- disable multiread by default for LPS22HB (only effects SPI)
* sun4i-gpadc-iio
- fix unbalanced irq enable / disable
* vf610
- Fix VALT slection for REFSEL bits - ensures we are using the
right reference pins.
This patch enables adc engine at initialization time and waits
for the initial sequence completion before enabling adc channels.
Without this code adc channels are not functional and shows
zeros for all connected channels.
Tested on mellanox msn platform.
v1 -> v2:
Pointed by Rick Altherr:
- Wait init sequence code enabled by bool
from OF match table.
Signed-off-by: Mykola Kostenok <c_mykolak@mellanox.com>
Reviewed-by: Rick Altherr <raltherr@google.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: linux-iio@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-amlogic@lists.infradead.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for active low interrupts (IRQF_TRIGGER_LOW and
IRQF_TRIGGER_FALLING). Configure the device as active high or low
according to the requested irq line.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Configure sensor ODR just in hts221_write_raw() in order to avoid
to set device sample rate multiple times.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
GENMASK(6, 3) in CTRL_REG1 and GENMASK(6, 2) in CTRL_REG2 are marked
reserved. Do not changed the original value (not declared in the
datasheet) during power-down/suspend routines.
Fixes: e4a70e3e7d (iio: humidity: add support to hts221 rh/temp device)
Fixes: b7079eeac5 (iio: humidity: hts221: add power management support)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Enable Block Data Update in hts221_probe() in order to avoid to reconfigure
it every time the sensor is enabled
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move bit-shift in hts221_write_with_mask() instead of coding
the shift depth in the configured value. That change will be necessary
to fix an issue in device power-down procedure.
Simplify hts221_avg_list table management
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for CCS811 VOC sensor. This patch adds support
for reading current and voltage across the sensor and TVOC
and equivalent CO2 values.
Scale and offset values have been computed according to datasheet:
- For current: raw value is in microamps
=> 0.001 scale to convert to milliamps
- For voltage: 1.65V = 1023, therefore 1650mV = 1023
=> 1650.0/1023 = 1.612903 scale to convert to millivolts
- For eCO2: raw value range is from 400ppm to 8192ppm.
=> (val - 400) * (100 - 0) / (8192 - 400) + 0 =
(val - 400) * 0.01283367 => offset: -400, scale = 0.012834
to get a percentage value
-For TVOC: raw value range is from 0ppb to 1187ppb.
=> (val - 0) * 100 / (1187 - 0) + 0 = val * 0.0842459 =>
scale = 0.084246 for getting a percentage value
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: Alison Schofield <amsfield22@gmail.com>
Signed-off-by: Narcisa Ana Maria Vasile <narcisaanamaria12@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The gpiod API checks for NULL descriptors, so there is no need to
duplicate the check in the driver.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Drop static on a local variable, when the variable is initialized before
any possible use. Thus, the static has no benefit.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
After probe we would put the device in normal mode, after a runtime
suspend-resume we would put it back in normal mode. But for a regular
suspend-resume we would only put it back in normal mode if triggers
or events have been requested. This is not consistent and breaks
reading raw values after a suspend-resume.
This commit changes the regular resume path to also unconditionally put
the device back in normal mode, fixing reading of raw values not working
after a regular suspend-resume cycle.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When adding maps to the list, they were added using list_add, which adds
them in LIFO order. When parsing using iio_channel_get_all(), these
elements are hence returned in reverse order. As a result, the iio_hwmon
mapping maps the first entry to the last channel and so on.
Signed-off-by: Gaurav Gupta <gauragup@cisco.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This adds support for STM32F4 Digital-To-Analog converter.
Add compatible configuration data to handle hfsel (not present
in stm32f4).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix error message, there's no 'st,dac-channel' property, but 'reg'
(see https://lkml.org/lkml/2017/4/3/567).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Don't populate array startup_lookup on the stack but instead make
it static. Makes the object code smaller.
Before:
text data bss dec hex filename
21754 5440 128 27322 6aba drivers/iio/adc/at91_adc.o
After:
text data bss dec hex filename
21613 5496 128 27237 6a65 drivers/iio/adc/at91_adc.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
I noticed in its DSDT that one of my tablets actually is using the GPADC
pin for temperature monitoring.
The whole axp288_adc_set_ts() function is a bit weird, in the past it was
removed because it seems to make no sense, then this was reverted because
of regressions.
So I decided to test the special GPADC pin handling on this tablet.
Conclusion: not only is axp288_adc_set_ts() necessary, we need to sleep a
bit after making the AXP288_ADC_TS_PIN_CTRL changes before sampling the
GPADC, otherwise it will often (about 80% of the time) read 0 instead of
its actual value.
It seems that there is only 1 bias current source and to be able to use it
for the GPIO0 pin in GPADC mode it must be temporarily turned off for the
TS pin, but the datasheet does not mention this.
This commit adds a sleep after disabling the TS pin bias current,
fixing the GPADC more often then not wrongly returning 0.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In order to use the standard name convention rename H3LIS331DL_DRIVER_NAME
macro in H3LIS331DL_ACCEL_DEV_NAME
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add H3LIS331DL, LIS331DL and LIS3LV02DL entries in st_accel_id_table
Fixes: 1e52fefc9b (iio: accel: Add support for the h3lis331dl accel)
Fixes: bbf5f037fa (iio: st_accel: support the LIS331DL sensor)
Fixes: 3acddf74f8 (iio: st-sensors: add support for lis3lv02d accel)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Making the const array startup_lookup static rather having it on the
stack saves 69 bytes. Add in missing int specifier to clean up a
checkpatch warning.
Before:
text data bss dec hex filename
10297 2800 128 13225 33a9 drivers/iio/adc/at91-sama5d2_adc.o
After:
text data bss dec hex filename
10140 2888 128 13156 3364 drivers/iio/adc/at91-sama5d2_adc.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Making the const array init_data static rather having it on the
stack saves us a couple hundreds of bytes:
Before:
text data bss dec hex filename
3175 848 0 4023 fb7 drivers/iio/accel/da311.o
After:
text data bss dec hex filename
2860 936 0 3796 ed4 drivers/iio/accel/da311.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Check return value from call to of_match_device()
in order to prevent a NULL pointer dereference.
In case of NULL print error message and return -ENODEV
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Check return value from call to of_match_device()
in order to prevent a NULL pointer dereference.
In case of NULL print error message and return -ENODEV
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds support for Diolan DLN2 ADC via IIO's ADC interface.
ADC is the fourth and final component of the DLN2 for the kernel.
Signed-off-by: Jack Andersen <jackoalan@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In order to select the alternate voltage reference pair (VALTH/VALTL), the
right value for the REFSEL field in the ADCx_CFG register is "01", leading
to 0x800 as register mask. See section 8.2.6.4 in the reference manual[1].
[1] http://www.nxp.com/docs/en/reference-manual/VFXXXRM.pdf
Fixes: a775427632 ("iio:adc:imx: add Freescale Vybrid vf610 adc driver")
Signed-off-by: Stefan-Gabriel Mirea <stefan-gabriel.mirea@nxp.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add SPI Serial Interface Mode (SIM) register information
in st_sensor_settings look up table to support devices
(like LSM303AGR accel sensor) that allow just SPI-3wire
communication mode. SIM mode has to be configured before any
other operation since it is not enabled by default and the driver
is not able to read without that configuration
Whilst a fairly substantial patch, the actual logic is simple and it
is better to have the generic fix than a band aid.
Fixes: ddc05fa286 (iio: st-accel: add support for lsm303agr accel)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add newlines to the macro definitions and use a more common style.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The LTC2741 and LTC2473 are single voltage ADC chips. The LTC2473
is similar to the LTC2471 but outputs a signed differential value.
Datasheet:
http://cds.linear.com/docs/en/datasheet/24713fb.pdf
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Set up and use triggered buffer if there is irq defined for device in
device tree. Trigger producer triggers from rpr0521 drdy interrupt line.
Trigger consumer reads rpr0521 data to scan buffer.
Depends on previous commits of _scale and _offset.
Signed-off-by: Mikko Koivunen <mikko.koivunen@fi.rohmeurope.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Inheriting the ADC BIAS current settings from the BIOS instead of
hardcoding then causes the AXP288 to disable charging (I think it
mis-detects an overheated battery) on at least one model tablet.
So lets go back to hard coding the values, this reverts
commit fa2849e964 ("iio: adc: axp288: Drop bogus
AXP288_ADC_TS_PIN_CTRL register modifications"), fixing charging not
working on the model tablet in question.
The exact cause is not fully understood, hence the revert to a known working
state.
Cc: stable@vger.kernel.org
Reported-by: Umberto Ixxo <sfumato1977@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When initializing interrupts, the devm_request_any_context_irq will
enable them right away. An atomic flag was set in sun4i_irq_init and read
in the interrupt handler to make sure no unwanted interrupts were
handled. If an unwanted interrupt occurred, the handler would disable
the irq and return IRQ_HANDLED. However, at the end of sun4i_irq_init,
the irq would be disabled as well, resulting in an unbalanced enable
(since there are more disables than enables, the code enabling the
interrupt would never be called).
When reading the ADC or the temperature, the respective irq would be
enabled in the read function and disabled in the irq handler. In the
read function, we would wait for a completion (with a timeout) that will
be set in the irq handler. However, if the completion is never set or if
the wait for completion times out, the irq would not be disabled in the
read function resulting in an unbalanced enable once the read function
is called again (since there are 2+ enables for no disable).
Moving disable_irq from the irq handler to the read function get rid of
these two cases of unbalanced enable.
Fixes: d1caa99055 ("iio: adc: add support for Allwinner SoCs ADC")
Reported-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
- Add PMBus client driver for IR35221
- Add support for NCT6795D to nct6775 driver
- Functional improvements to adt7475, aspeed-pwm-tacho, and ibmpowernv drivers
- Minor fixes and cleanups in various drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=J5ye
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus-v4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- Add PMBus client driver for IR35221
- Add support for NCT6795D to nct6775 driver
- Functional improvements to adt7475, aspeed-pwm-tacho, and ibmpowernv
drivers
- Minor fixes and cleanups in various drivers
* tag 'hwmon-for-linus-v4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (22 commits)
hwmon: (aspeed-pwm-tacho) Poll with short sleeps.
hwmon: (aspeed-pwm-tacho) reduce fan_tach period
hwmon: (ibmpowernv) Add current(A) sensor
hwmon: (ibmpowernv) introduce a legacy_compatibles array
hwmon: (pwm-fan) Switch to new atomic PWM API
hwmon: (scpi) Fix the scale of SCP sensor readings
hwmon: (aspeed-pwm-tacho) Enable both edge measurement.
hwmon: (ibmpowernv) Add highest/lowest attributes to sensors
hwmon: (pmbus) move header file out of I2C realm
hwmon: (max6639) move header file out of I2C realm
hwmon: (ltc4245) move header file out of I2C realm
hwmon: (ds620) move header file out of I2C realm
hwmon: (ads1015) move header file out of I2C realm
hwmon: (adt7475) temperature smoothing
hwmon: (adt7475) add high frequency support
hwmon: (adt7475) fan stall prevention
hwmon: (adt7475) replace find_nearest() with find_closest()
hwmon: (pmbus) Add client driver for IR35221
hwmon: (nct6775) Add support for NCT6795D
hwmon: (nct6775) Improve fan detection
...
Here is the "big" char/misc driver patchset for 4.13-rc1.
Lots of stuff in here, a large thunderbolt update, w1 driver header
reorg, the new mux driver subsystem, google firmware driver updates, and
a raft of other smaller things. Full details in the shortlog.
All of these have been in linux-next for a while with the only reported
issue being a merge problem with this tree and the jc-docs tree in the
w1 documentation area. The fix should be obvious for what to do when it
happens, if not, we can send a follow-up patch for it afterward.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWVpXKA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynLrQCdG9SxRjAbOd6pT9Fr2NAzpUG84YsAoLw+I3iO
EMi60UXWqAFJbtVMS9Aj
=yrSq
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc updates from Greg KH:
"Here is the "big" char/misc driver patchset for 4.13-rc1.
Lots of stuff in here, a large thunderbolt update, w1 driver header
reorg, the new mux driver subsystem, google firmware driver updates,
and a raft of other smaller things. Full details in the shortlog.
All of these have been in linux-next for a while with the only
reported issue being a merge problem with this tree and the jc-docs
tree in the w1 documentation area"
* tag 'char-misc-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (147 commits)
misc: apds990x: Use sysfs_match_string() helper
mei: drop unreachable code in mei_start
mei: validate the message header only in first fragment.
DocBook: w1: Update W1 file locations and names in DocBook
mux: adg792a: always require I2C support
nvmem: rockchip-efuse: add support for rk322x-efuse
nvmem: core: add locking to nvmem_find_cell
nvmem: core: Call put_device() in nvmem_unregister()
nvmem: core: fix leaks on registration errors
nvmem: correct Broadcom OTP controller driver writes
w1: Add subsystem kernel public interface
drivers/fsi: Add module license to core driver
drivers/fsi: Use asynchronous slave mode
drivers/fsi: Add hub master support
drivers/fsi: Add SCOM FSI client device driver
drivers/fsi/gpio: Add tracepoints for GPIO master
drivers/fsi: Add GPIO based FSI master
drivers/fsi: Document FSI master sysfs files in ABI
drivers/fsi: Add error handling for slave
drivers/fsi: Add tracepoints for low-level operations
...
This patch fixes the following checkpatch warnings:
Prefer 'unsigned int' to bare use of 'unsigned
Signed-off-by: Reno Farnesi <nfarnesi4@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add device tree support for LPS22HB, LPS25H, LPS331AP, LPS001WP
pressure sensors
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add device tree support for LIS3MDL and LSM303AGR magnetometer sensors
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Don't inflate the kernel size with data that isn't used. The conditional
declaration also fixes the following warning when building with clang:
drivers/iio/magnetometer/ak8975.c:704:36: error: variable 'ak_acpi_match'
is not needed and will not be emitted
[-Werror,-Wunneeded-internal-declaration]
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add missing hooks in the LTC2497 IIO driver to allow hwmon mapping.
Signed-off-by: Gaurav Gupta <gauragup@cisco.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The array stm32h7_adc_ckmodes_spec does not need to be in global scope, so
make it static.
Cleans up sparse warning:
"symbol 'stm32h7_adc_ckmodes_spec' was not declared. Should it be static?"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Some part of the configuration are not touched after the probe
and if something goes wrong on writing the initial one,
the chip will misbehave.
Adding an error checking ensures that the inital configuration will
be written correctly. Moreover ensures that a sensible configuration
will be saved in driver data and used subsequently as intended.
Signed-off-by: Angelo Compagnucci <angelo.compagnucci@gmail.com>
Reported-by: Maarten Brock <m.brock@vanmierlo.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Initial channel should be the first available channel on
all configurations, so changing to channel 0 available on
all supported chips.
Signed-off-by: Angelo Compagnucci <angelo.compagnucci@gmail.com>
Reported-by: Maarten Brock <m.brock@vanmierlo.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Open drain should work fine with rising or high level IRQs,
this code was due to some misunderstanding on my part.
Reported-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add a link to the TCS3472 datasheet in the AMS's website.
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch supports auxadc suspend/resume flow.
Disable auxadc clk and power in suspend function.
Enable axuadc clk and power in resume function.
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add open drain support in order to share requested IRQ line between
st_lsm6dsx device and other peripherals
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add of_match_table for Measurement-Specialties htu21 temperature & humidity sensor and humidity part of MS8607 sensor
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added support for suspend/resume functionality for the ADC IP
in sama5d2 SoC.
In order to enter Suspend to ram mode (backup + self refresh mode for
memory), in which the ADC IP is no longer powered, we need to reset the
pins to default state, for the scenario when they are also used for I2C
bus to communicate with the PMIC.
On resume, we need to reconfigure the ADC IP registers and reconfigure the
trigger registers in the case when the suspend procedure is done while
sysfs has the buffer and trigger enabled.
In the case the suspend happens exactly during a software triggered
conversion, the request will time out, because we reset and power down
the ADC.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In order to add proper device tree support give a more general name
to of_device_id table
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Move st_sensors_of_i2c_probe() in st_sensors_core and rename it in
st_sensors_of_name_probe(). That change is necessary to add device-tree
support in spi code otherwise the rest of the autodetection will fail
since spi->modalias (and indio_dev->name) will be set using compatible
string value that differs from standard sensor name
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Enable multiread by default for LIS3MDL since using I2C interface
the subaddr Msb is used to automatically increase the slave address
during multiple data read/write. In the same way, using SPI interface,
bit 1 in register address is used to enable auto-increment of the slave
address in multiple read/write.
Fixes: 872e79add7 (iio:magn: Add STMicroelectronics magn driver)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
