dma_request_chan() can fail returning an error pointer. In this case
prevent calling dma_release_channel() to prevent a ERR_PTR() dereference.
As error path can be called even with no DMA configuration, info->dma can
be NULL so don't call dma_release_channel() for that case either.
Fixes: de3bfc4a16: ("mtd: nand: omap2: fix return value check in omap_nand_probe()")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
NAND:
Updates from Boris:
"""
This pull request contains only one notable change:
* Addition of the MTK NAND controller driver
And a bunch of specific NAND driver improvements/fixes. Here are the
changes that are worth mentioning:
* A few fixes/improvements for the xway NAND controller driver
* A few fixes for the sunxi NAND controller driver
* Support for DMA in the sunxi NAND driver
* Support for the sunxi NAND controller IP embedded in A23/A33 SoCs
* Addition for bitflips detection in erased pages to the brcmnand driver
* Support for new brcmnand IPs
* Update of the OMAP-GPMC binding to support DMA channel description
"""
In addition, some small fixes around error handling, etc., as well as one
long-standing corner case issue (2.6.20, I think?) with writing 1 byte less
than a page.
NOR:
* Rework some error handling on reads and writes, so we can better handle (for
instance) SPI controllers which have limitations on their maximum transfer size
* Add new Cadence Quad SPI flash controller driver
* Add new Atmel QSPI flash controller driver
* Add new Hisilicon SPI flash controller driver
* Support a few new flash, and update supported features on others
* Fix the logic used for detecting a fully-unlocked flash
And other miscellaneous small fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXn/j0AAoJEFySrpd9RFgto58P/j1huB0d21zFen3teo8YKKr1
dLi65mFbqtpU1BLqD07uc2gsH17kvezFJCtx8H8Jp/yCjLF2kYIKL7wDTf6OJPtn
aYGS5dG5jhMIq+6CD2olKqy+IVLfL9GvCf44Z3fpVta5lOn09y7Jm0AkBjmJcH45
SdJi+iUkSKhqRY3O2udyauGyL4JWG7eHUonrG9g8ROrO0GWQkT4Ijm1ZwIBlFDkJ
e1N960OqPg5ISOzuTeM14Ok9IUyeb7wiXhqRfOJgzNk6iBcN1YC2ono3C7RH2sN7
wiyCqqUpDDCDBDiFdGOdpc9cjzNysrt02ypWRsZIpQVCm89nPLSutqQEWLuo0qzq
/eIzdwbk1AxX96CeQohOezqL+n6+RHP9AIvwzL9GeWjipD1LBvfM1l3CmuSKK5jb
bQ4CA/FVz1tO/25q8tuLJfpFzhFE2PC3pphVf8tREL/U6OR/97NgDMuQIuqiQpRc
4nJtu79yacAzEiztZh0bsx+t94QFE+kfs/6d8m+llLEyx2sI8HKZeDvNRwEB0OsD
wQ5bjyd54m7+i4H8njrnOTP+K2YrwNjGlbTo7qrRSpFMDr4mD0VQLap03Srvo5xV
OYB6uGZhGV2L3k6nG5wywM2z6Hw0QfHxjrpcLyG51xABmni2QF3lOdYSllRtRTXp
aYLfPUqgIgSUI2GTDHyW
=HQr0
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20160801' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"NAND:
Quoting Boris:
'This pull request contains only one notable change:
- Addition of the MTK NAND controller driver
And a bunch of specific NAND driver improvements/fixes. Here are the
changes that are worth mentioning:
- A few fixes/improvements for the xway NAND controller driver
- A few fixes for the sunxi NAND controller driver
- Support for DMA in the sunxi NAND driver
- Support for the sunxi NAND controller IP embedded in A23/A33 SoCs
- Addition for bitflips detection in erased pages to the brcmnand driver
- Support for new brcmnand IPs
- Update of the OMAP-GPMC binding to support DMA channel description'
In addition, some small fixes around error handling, etc., as well
as one long-standing corner case issue (2.6.20, I think?) with
writing 1 byte less than a page.
NOR:
- rework some error handling on reads and writes, so we can better
handle (for instance) SPI controllers which have limitations on
their maximum transfer size
- add new Cadence Quad SPI flash controller driver
- add new Atmel QSPI flash controller driver
- add new Hisilicon SPI flash controller driver
- support a few new flash, and update supported features on others
- fix the logic used for detecting a fully-unlocked flash
And other miscellaneous small fixes"
* tag 'for-linus-20160801' of git://git.infradead.org/linux-mtd: (60 commits)
mtd: spi-nor: don't build Cadence QuadSPI on non-ARM
mtd: mtk-nor: remove duplicated include from mtk-quadspi.c
mtd: nand: fix bug writing 1 byte less than page size
mtd: update description of MTD_BCM47XXSFLASH symbol
mtd: spi-nor: Add driver for Cadence Quad SPI Flash Controller
mtd: spi-nor: Bindings for Cadence Quad SPI Flash Controller driver
mtd: nand: brcmnand: Change BUG_ON in brcmnand_send_cmd
mtd: pmcmsp-flash: Allocating too much in init_msp_flash()
mtd: maps: sa1100-flash: potential NULL dereference
mtd: atmel-quadspi: add driver for Atmel QSPI controller
mtd: nand: omap2: fix return value check in omap_nand_probe()
Documentation: atmel-quadspi: add binding file for Atmel QSPI driver
mtd: spi-nor: add hisilicon spi-nor flash controller driver
mtd: spi-nor: support dual, quad, and WP for Gigadevice
mtd: spi-nor: Added support for n25q00a.
memory: Update dependency of IFC for Layerscape
mtd: nand: jz4780: Update MODULE_AUTHOR email address
mtd: nand: sunxi: prevent a small memory leak
mtd: nand: sunxi: add reset line support
mtd: nand: sunxi: update DT bindings
...
nand_do_write_ops() determines if it is writing a partial page with the
formula:
part_pagewr = (column || writelen < (mtd->writesize - 1))
When 'writelen' is exactly 1 byte less than the NAND page size the formula
equates to zero, so the code doesn't process it as a partial write,
although it should.
As a consequence the function remains in the while(1) loop with 'writelen'
becoming 0xffffffff and iterating endlessly.
The bug may not be easy to reproduce in Linux since user space tools
usually force the padding or round-up the write size to a page-size
multiple.
This was discovered in U-Boot where the issue can be reproduced by
writing any size that is 1 byte less than a page-size multiple.
For example, on a NAND with 2K page (0x800):
=> nand erase.part <partition>
=> nand write $loadaddr <partition> 7ff
[Editor's note: the bug was added in commit 29072b9607, but moved
around in commit 66507c7bc8 ("mtd: nand: Add support to use nand_base
poi databuf as bounce buffer")]
Fixes: 29072b9607 ("[MTD] NAND: add subpage write support")
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Change the BUG_ON() condition in brcmnand_send_cmd() which checks for
the interrupt status "controller ready" bit to a WARN_ON.
There is no good reason to kill the system when this condition occur
because we could have systems which listed the NAND controller as
available (e.g: from Device Tree), but the NAND chip could be
malfunctioning and not responding.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In case of error, the function dma_request_chan() returns ERR_PTR() and
never returns NULL. The NULL test in the return value check should be
replaced with IS_ERR().
Fixes: aa7abd312c ('mtd: nand: omap2: Support parsing dma channel
information from DT')
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
* Addition of the MTK NAND controller driver
And a bunch of specific NAND driver improvements/fixes. Here are the
changes that are worth mentioning:
* A few fixes/improvements for the xway NAND controller driver
* A few fixes for the sunxi NAND controller driver
* Support for DMA in the sunxi NAND driver
* Support for the sunxi NAND controller IP embedded in A23/A33 SoCs
* Addition for bitflips detection in erased pages to the brcmnand driver
* Support for new brcmnand IPs
* Update of the OMAP-GPMC binding to support DMA channel description
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8Aeb
-----END PGP SIGNATURE-----
Merge tag 'nand/for-4.8' of github.com:linux-nand/linux into mtd
Pull NAND changes from Boris Brezillon:
"""
This pull request contains only one notable change:
* Addition of the MTK NAND controller driver
And a bunch of specific NAND driver improvements/fixes. Here are the
changes that are worth mentioning:
* A few fixes/improvements for the xway NAND controller driver
* A few fixes for the sunxi NAND controller driver
* Support for DMA in the sunxi NAND driver
* Support for the sunxi NAND controller IP embedded in A23/A33 SoCs
* Addition for bitflips detection in erased pages to the brcmnand driver
* Support for new brcmnand IPs
* Update of the OMAP-GPMC binding to support DMA channel description
"""
commit c9711ec525 ("mtd: nand: omap: Clean up device tree support")
removes the check for the old elm phandle binding.
Add it again to keep backward compatibility.
Fixes: commit c9711ec525 ("mtd: nand: omap: Clean up device tree support")
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch enables IFC NAND support on ARM layerscape platform.
It fixes the dependency to enable NAND. The include files are being modified
to ensure complilation for both PowerPC and ARM architectures.
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Acked-by: Scott Wood <oss@buserror.net>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Emails will bounce from my imgtec address, so update it to a new one.
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Cc: Harvey Hunt <harveyhuntnexus@gmail.com>
Cc: linux-mtd@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
I moved the sanity check on ecc->size before the allocation so that we
don't leak memory on error.
Fixes: 05af074a4b73 ('mtd: nand: sunxi: check ecc->size values')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The NAND controller on some sun8i chips needs its reset line to be
deasserted before they can enter working state.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Instead of using IO_ADDR_W and IO_ADDR_R use an own pointer to the NAND
controller memory area.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This driver needs a special write_buf and read_buf function, because we
have to read from a specific address to tell the controller this is a
read from the nand controller.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Extract the functions to read and write to the register of the NAND
flash controller.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The external Bus Unit (EBU) can control different flash devices, but
these NAND flash commands have to be atomic and should not be
interrupted in between. Lock the EBU from the beginning of the command
till the end by moving the lock to the chip select.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
nand_scan() already resets the NAND flash chip, this driver does not
have to call it manually. The xway_reset_chip() functions does the same
as the normal NAND reset function. The waiting for the NAND_WAIT_WR_C
is done in xway_cmd_ctrl().
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The ->cmd_ctrl() function is adjusting the ->IO_ADDR_W value depending
on the command type each time NAND_CTRL_CHANGE is passed. This is not
only useless but can lead to an ->IO_ADDR_W corruption.
Get rid of this logic and rely on the NAND_CLE and NAND_ALE flags to
deduce the iomem address to write the cmd argument to.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Instead of hacking this into the plat_nand driver just make this a
normal nand driver.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This adds some register documentation which should make it easier to
understand how this controller works. In addition it makes now use of
BIT() macro and adds some more defines.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Implement ecc->write_subpage() to prevent core code from assigning this
hook to nand_write_subpage_hwecc(). This default implementation tries
to call ecc->hwctl() which in our case is NULL, thus leading to a NULL
pointer dereference.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Verify that the ecc->size value is either 512 or 1024 bytes.
This should always be the case if this field was assigned to the
nand->ecc_step_size_ds value, but can be wrong when the user overloaded
this value with the nand-ecc-step-size DT property.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Switching to 1k ECC blocks when possible provides better resistance against
concentrated bitflips. Say you have those two configurations:
1/ 16bits/512bytes
2/ 32bits/1024bytes
Both of them require the same amount of ECC bytes (only true for this
specific engine), but the second config allows you to correct the case
where most of your bitflips are concentrated in a single 512bytes portion.
This fact makes the 1k ECC block size more advantageous than the 512bytes
one.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The column address passed to the RNDOUT operation was missing the page
size offset.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: 614049a8d9 ("mtd: nand: sunxi: add support for DMA assisted operations")
Add support for mediatek's SDG1 NFC nand controller embedded in SoC
2701
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Xiaolei Li <xiaolei.li@mediatek.com>
In case of error, the function dmaengine_prep_slave_sg() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Fixes: 614049a8d9 ("mtd: nand: sunxi: add support for DMA assisted operations")
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This change provides a fix for controller bug where nand
controller could have a possible sticky error after a PIO
followed by a DMA read. The fix retries a read if we see
a uncorr_ecc after read to detect such sticky errors.
The fix applies to only controller version 7.0 and 7.1.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Check for erased page bitflips in a page. And if well within
threshold return data as all 0xff. Apply sw check for controller
version < 7.2. Controller vesion >= 7.2 has hw support.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
I got device with ESMT (Elite Semiconductor Memory Technology Inc)
F59L1G81MA flash that was detected as:
[ 0.852034] nand: device found, Manufacturer ID: 0xc8, Chip ID: 0xd1
[ 0.858402] nand: Unknown NAND 128MiB 3,3V 8-bit
[ 0.863031] nand: 128MiB, SLC, page size: 2048, OOB size: 64
According to the F59L1G81MA datasheet (and Read Id documentation) C8h is
a "Maker Code" which should mean ESMT. Add it to fix above "Unknown".
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The sunxi NAND controller is able to pipeline ECC operations only when
operated in DMA mode, which improves a lot NAND throughput while keeping
CPU usage low.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The 7.2 controller differs in a few area compared to its predecssor (7.1):
- NAND scrambler, which we are not using just yet
- higher ECC levels (up to 120 bits) per 1KB data blocks, also not supported yet
- up to 128B OOB
This patch adds the necessary code to support such a controller
generation and updates the Device Tree binding.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Kamal Dasu <kdasu.kdev@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Switch from dma_request_channel to allow passing dma channel
information from DT rather than hardcoding a value.
Also provide a handle to the GPMC's dev so it can be used to parse the DMA
channel information within the GPMC's DT node.
Performance Numbers via mtd_speedtest now that EDMA based prefetch works:
AM335x Performance numbers:
DMA
CPULOAD Write: 54% Read: 35%
page write speed -23% (vs non dma)
page read speed -35% (vs non dma)
NO DMA (prefetch-polled)
CPULOAD Write: 98% Read: 98%
AM437x Performance numbers:
DMA
CPU LOAD Write: 56% Read: 36%
page write speed -16% (vs non dma)
page read speed -22% (vs non dma)
NO DMA (prefetch-polled)
CPULOAD Write: 93% Read: 93%
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
We've already noticed a few flaws in the MTD work for v4.7-rc1:
* The Atmel folks got ahead of themselves on trying to support their latest
hardware and were working off incorrect documentation. Fix up the NAND
driver to get this correct.
* Fix up device tree example documentation to use the latest recommendations
for describing NAND ECC algorithms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXSH51AAoJEFySrpd9RFgtSnsQAK+UrSM1gFAiMBEWPJuCK100
WZRZG8FxftzGbU33DiSgXDU/RmZBupIBHSZNGoWBkumdd9uozfIWp+s2T40k2ot6
E7ckF3lGaZOWMmzt/MN5lkeTm6Pzs63DemP/a1wSRqfvCTE8kB8EREzUiTQuNnWi
6YMvXuVnwouh5v91vuwKOKmGWuYidy6sF91w8ucd+W/A7p0Rnj8Nr7cGur3Xn+6L
MNjvfvD8tfyKk3b7aaNMyR6oIJQ9awR2TewBbB/6mJQR/eDOPnpq3Z+rJSwEoSJH
Hd/pG0zx9KeZyOF7kbZZmfk9DyPM50qCxiX/Z9kaSMGxyEQgwMjmQslJbDvRGOz5
2s5NAT8Nm3OcedAJgjGLmUlO/NH4XIQt+c35nftikeNplUqNNbZLjMgpfnLWB8FN
5cerUeFBwFZztJIWN1eQfZ7lERwk8bJPr0IRfPASj0xjTXi1DZze7WijA/BrsvEc
rUQ8J1YAXvjVyQZUmJyq8MFVeyEewv1MZ0O5w0t0u7kXtVI3HLQiJCLy1ZD3rDm2
dW4hMVtLOu6WDGZ27a229QtXOEm5L0YXCQGea75zR+gQObiY8mMIN3Qy68W4zSSJ
yGMPY9u8E8oPHh7TeNtc4E8MkYbujqknIshcgTBN2k4HufK6GPZOTvwfor1zdHAe
HGk9MiFRrACPTQIuxfhd
=kb+w
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20160527' of git://git.infradead.org/linux-mtd
Pull MTD fixes from Brian Norris:
"We've already noticed a few flaws in the MTD work for v4.7-rc1:
- The Atmel folks got ahead of themselves on trying to support their
latest hardware and were working off incorrect documentation. Fix
up the NAND driver to get this correct.
- Fix up device tree example documentation to use the latest
recommendations for describing NAND ECC algorithms"
* tag 'for-linus-20160527' of git://git.infradead.org/linux-mtd:
Documentation: dt: mtd: drop "soft_bch" from example
Revert "mtd: atmel_nand: Support variable RB_EDGE interrupts"
This reverts commit 5ddc7bd43c ("mtd: atmel_nand: Support variable
RB_EDGE interrupts")
Because for current SoCs, the RB_EDGE3(i.e. bit 27) of HSMC_SR
register does not exist, the RB_EDGE0 (i.e. bit 24) is the ready/busy
line edge status bit. It is a datasheet bug.
Cc: <stable@vger.kernel.org>
Fixes: commit 5ddc7bd43c ("mtd: atmel_nand: Support variable RB_EDGE interrupts")
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
First cycle with Boris as NAND maintainer! Many (most) bullets stolen from him.
Generic:
* Migrated NAND LED trigger to be a generic MTD trigger
NAND:
* Introduction of the "ECC algorithm" concept, to avoid overloading the ECC
mode field too much more
* Replaced the nand_ecclayout infrastructure with something a little more
flexible (finally!) and future proof
* Rework of the OMAP GPMC and NAND drivers; the TI folks pulled some of
this into their own tree as well
* Prepare the sunxi NAND driver to receive DMA support
* Handle bitflips in erased pages on GPMI revisions that do not support
this in hardware.
SPI NOR:
* Start using the spi_flash_read() API for SPI drivers that support it (i.e.,
SPI drivers with special memory-mapped flash modes)
And other small scattered improvments.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=J6KN
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20160523' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"First cycle with Boris as NAND maintainer! Many (most) bullets stolen
from him.
Generic:
- Migrated NAND LED trigger to be a generic MTD trigger
NAND:
- Introduction of the "ECC algorithm" concept, to avoid overloading
the ECC mode field too much more
- Replaced the nand_ecclayout infrastructure with something a little
more flexible (finally!) and future proof
- Rework of the OMAP GPMC and NAND drivers; the TI folks pulled some
of this into their own tree as well
- Prepare the sunxi NAND driver to receive DMA support
- Handle bitflips in erased pages on GPMI revisions that do not
support this in hardware.
SPI NOR:
- Start using the spi_flash_read() API for SPI drivers that support
it (i.e., SPI drivers with special memory-mapped flash modes)
And other small scattered improvments"
* tag 'for-linus-20160523' of git://git.infradead.org/linux-mtd: (155 commits)
mtd: spi-nor: support GigaDevice gd25lq64c
mtd: nand_bch: fix spelling of "probably"
mtd: brcmnand: respect ECC algorithm set by NAND subsystem
gpmi-nand: Handle ECC Errors in erased pages
Documentation: devicetree: deprecate "soft_bch" nand-ecc-mode value
mtd: nand: add support for "nand-ecc-algo" DT property
mtd: mtd: drop NAND_ECC_SOFT_BCH enum value
mtd: drop support for NAND_ECC_SOFT_BCH as "soft_bch" mapping
mtd: nand: read ECC algorithm from the new field
mtd: nand: fsmc: validate ECC setup by checking algorithm directly
mtd: nand: set ECC algorithm to Hamming on fallback
staging: mt29f_spinand: set ECC algorithm explicitly
CRIS v32: nand: set ECC algorithm explicitly
mtd: nand: atmel: set ECC algorithm explicitly
mtd: nand: davinci: set ECC algorithm explicitly
mtd: nand: bf5xx: set ECC algorithm explicitly
mtd: nand: omap2: Fix high memory dma prefetch transfer
mtd: nand: omap2: Start dma request before enabling prefetch
mtd: nandsim: add __init attribute
mtd: nand: move of_get_nand_xxx() helpers into nand_base.c
...
Pull LED updates from Jacek Anaszewski:
"In this merge cycle we had an interaction with MTD subsystem, that
included converting drivers/mtd/nand/nand_base.c to use newly
introduced MTD (NAND/NOR) LED trigger instead of implementing it on
its own.
Related MTD patches are intended to be merged through the LED tree,
before MTD tree is merged, since further MTD development is based on
those modifications.
Summary:
LEDs:
- Introduce a kernel panic LED trigger
- Introduce a MTD (NAND/NOR) trigger
- led-tca6507: silence an uninitialized variable warning
- ledtrig-ide-disk: Move ide_blink_delay to ledtrig_ide_activity()
- leds-ss4200: Add depend on x86 arch
- leds-ss4200: add DMI data for FSC SCALEO Home Server
- leds-triggers: Allow to switch the trigger to "panic" on a kernel panic
- devicetree: leds: Introduce "panic-indicator" optional property
- leds-gpio: Support the "panic-indicator" firmware property
MTD:
- Uninline mtd_write_oob and move it to mtdcore.c
- Remove the "nand-disk" LED trigger
- Hook I/O activity to the MTD LED trigger"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
leds: gpio: Support the "panic-indicator" firmware property
devicetree: leds: Introduce "panic-indicator" optional property
leds: triggers: Allow to switch the trigger to "panic" on a kernel panic
leds: ss4200: add DMI data for FSC SCALEO Home Server
leds: ss4200: Add depend on x86 arch
leds: ledtrig-ide-disk: Move ide_blink_delay to ledtrig_ide_activity()
leds: tca6507: silence an uninitialized variable warning
mtd: Hook I/O activity to the MTD LED trigger
mtd: nand: Remove the "nand-disk" LED trigger
leds: trigger: Introduce a MTD (NAND/NOR) trigger
mtd: Uninline mtd_write_oob and move it to mtdcore.c
leds: trigger: Introduce a kernel panic LED trigger
* introduction of the ECC algo concept to extend the ECC mode one
* replacement of the nand_ecclayout infrastructure by something more
future-proof.
* addition of an mtd-activity led trigger to replace the nand-activity
one
And a bunch of specific NAND driver improvements/fixes. Here are the
changes that are worth mentioning:
* rework of the OMAP GPMC and NAND drivers
* prepare the sunxi NAND driver to receive DMA support
* handle bitflips in erased pages on GPMI revisions that do not support
this in hardware.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=PYza
-----END PGP SIGNATURE-----
Merge tag 'nand/for-4.7' of github.com:linux-nand/linux
Updates from Boris Brezillon:
This pull request contains the following infrastructure changes:
* introduction of the ECC algo concept to extend the ECC mode one
* replacement of the nand_ecclayout infrastructure by something more
future-proof.
* addition of an mtd-activity led trigger to replace the nand-activity
one
And a bunch of specific NAND driver improvements/fixes. Here are the
changes that are worth mentioning:
* rework of the OMAP GPMC and NAND drivers
* prepare the sunxi NAND driver to receive DMA support
* handle bitflips in erased pages on GPMI revisions that do not support
this in hardware.
* tag 'nand/for-4.7' of github.com:linux-nand/linux: (152 commits)
mtd: brcmnand: respect ECC algorithm set by NAND subsystem
gpmi-nand: Handle ECC Errors in erased pages
Documentation: devicetree: deprecate "soft_bch" nand-ecc-mode value
mtd: nand: add support for "nand-ecc-algo" DT property
mtd: mtd: drop NAND_ECC_SOFT_BCH enum value
mtd: drop support for NAND_ECC_SOFT_BCH as "soft_bch" mapping
mtd: nand: read ECC algorithm from the new field
mtd: nand: fsmc: validate ECC setup by checking algorithm directly
mtd: nand: set ECC algorithm to Hamming on fallback
staging: mt29f_spinand: set ECC algorithm explicitly
CRIS v32: nand: set ECC algorithm explicitly
mtd: nand: atmel: set ECC algorithm explicitly
mtd: nand: davinci: set ECC algorithm explicitly
mtd: nand: bf5xx: set ECC algorithm explicitly
mtd: nand: omap2: Fix high memory dma prefetch transfer
mtd: nand: omap2: Start dma request before enabling prefetch
mtd: nandsim: add __init attribute
mtd: nand: move of_get_nand_xxx() helpers into nand_base.c
mtd: nand: sh_flctl: rely on generic DT parsing done in nand_scan_ident()
mtd: nand: mxc: rely on generic DT parsing done in nand_scan_ident()
...
This is more obvious than guessing based on ECC strength. It allows
using NAND on devices with BCH-1 (e.g. D-Link DIR-885L).
This maintains DT backward compatibility by defaulting to Hamming if a
1-bit ECC algorithm is specified without a corresponding algorithm
selection. i.e., to use BCH-1, you must specify:
nand-ecc-strength = <1>;
nand-ecc-step-size = <512>;
nand-ecc-algo = "bch";
Also adds a check to ensure we haven't allowed someone to get by with SW
ECC. If we want to support SW ECC, we need to refactor some other pieces
of this driver.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
ECC is only calculated for written pages. As erased pages are not
actively written the ECC is always invalid. For this purpose the
Hardware BCH unit is able to check for erased pages and does not raise
an ECC error in this case. This behaviour can be influenced using the
BCH_MODE register which sets the number of allowed bitflips in an erased
page. Unfortunately the unit is not capable of fixing the bitflips in
memory.
To avoid complete software checks for erased pages, we can simply check
buffers with uncorrectable ECC errors because we know that any erased
page with errors is uncorrectable by the BCH unit.
This patch adds the generic nand_check_erased_ecc_chunk() to gpmi-nand
to correct erased pages. To have the valid data in the buffer before
using them, this patch moves the read_page_swap_end() call before the
ECC status checking for-loop.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
[Squashed patches by Stefan and Boris to check ECC area]
Tested-by: Stefan Christ <s.christ@phytec.de>
Acked-by: Han xu <han.xu@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
So far it was only possible to specify ECC algorithm using "soft" and
"soft_bch" values of nand-ecc-mode prop. There wasn't a way to specify
it for a hardware ECC mode.
Now that we have independent field in NAND subsystem for storing info
about ECC algorithm we may also add support for this new DT property.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This value should not be part of nand_ecc_modes_t as it specifies
algorithm not a mode. We successfully managed to introduce new "algo"
field which is respected now.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
There isn't any difference between handling NAND_ECC_SOFT and
NAND_ECC_SOFT_BCH now. What matters is the new field called "algo".
Please note we're keeping backward DT compatibility. We are still
treating "soft_bch" value as the one setting Hamming algorithm, it's
just handled in of_get_nand_ecc_algo now.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Now we have all drivers properly setting this new field we can start
using it. For a very short period of time we should support both values:
NAND_ECC_SOFT and NAND_ECC_SOFT_BCH treating them the same. It's because
of_get_nand_ecc_mode may still be setting NAND_ECC_SOFT_BCH.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
NAND core sets ECC algorithm in algo field now and it should be
preferred over the mode field. This also prepares driver for dropping
NAND_ECC_SOFT_BCH.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Based on DMA documentation and testing using high memory buffer when doing
dma transfers can lead to various issues including kernel panics.
To workaround this simply use cpu copy.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The prefetch engine sends a dma request once a FIFO threshold has
been met. No other requests are received until the previous request
is handled.
Starting a dma transfer (dma_async_issue_pending) results in any
previous event for the dma channel to be cleared. Therefore, starting
the prefetch engine before initiating the dma transfer may result in
the prefetch triggering a dma request but instead of it being handled
it can end up being cleared. This will result in a hang since the code
will continue to wait for the dma request to complete.
By initiating the dma request before enabling the prefetch engine this
race condition is avoided and no dma request are missed/cleared.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Add __init attribute on functions that are only called from other __init
functions and that are not inlined, at least with gcc version 4.8.4 on an
x86 machine with allyesconfig. Currently, the functions are put in the
.text.unlikely segment. Declaring them as __init will cause them to be
put in the .init.text and to disappear after initialization.
The result of objdump -x on the functions before the change is as follows:
000000000000059a l F .text.unlikely 0000000000000239 alloc_device
000000000000034e l F .text.unlikely 000000000000002e get_partition_name
00000000000007d3 l F .text.unlikely 00000000000005da init_nandsim
And after the change it is as follows:
0000000000000029 l F .init.text 0000000000000234 alloc_device
0000000000000000 l F .init.text 0000000000000029 get_partition_name
000000000000025d l F .init.text 00000000000005d5 init_nandsim
Done with the help of Coccinelle. The semantic patch checks for local
static non-init functions that are called from an __init function and are
not called from any other function.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Now that all drivers go through nand_set_flash_node() to parse the generic
NAND properties, we can move all of_get_nand_xxx() helpers in to
nand_base.c, make them static and remove of_mtd.c and of_mtd.h.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The core now takes care of parsing generic DT properties in
nand_scan_ident() when nand_set_flash_node() has been called.
Rely on this initialization instead of calling of_get_nand_xxx()
manually.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The core now takes care of parsing generic DT properties in
nand_scan_ident() when nand_set_flash_node() has been called.
Rely on this initialization instead of calling of_get_nand_xxx()
manually.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The core now takes care of parsing generic DT properties in
nand_scan_ident() when nand_set_flash_node() has been called.
Rely on this initialization instead of calling of_get_nand_xxx()
manually.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The core now takes care of parsing generic DT properties in
nand_scan_ident() when nand_set_flash_node() has been called.
Rely on this initialization instead of calling of_get_nand_xxx()
manually.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The core now takes care of parsing generic DT properties in
nand_scan_ident() when nand_set_flash_node() has been called.
Rely on this initialization instead of calling of_get_nand_xxx()
manually.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The core now takes care of parsing generic DT properties in
nand_scan_ident() when nand_set_flash_node() has been called.
Rely on this initialization instead of calling of_get_nand_xxx()
manually.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Han xu <han.xu@nxp.com>
Move constants to the right of binary operators.
Generated by: scripts/coccinelle/misc/compare_const_fl.cocci
CC: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Now that all NAND drivers have switched to mtd_ooblayout_ops, we can kill
the ecc->layout field.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Implementing the mtd_ooblayout_ops interface is the new way of exposing
ECC/OOB layout to MTD users.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Archit Taneja <architt@codeaurora.org>
Implementing the mtd_ooblayout_ops interface is the new way of exposing
ECC/OOB layout to MTD users.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Stefan Agner <stefan@agner.ch>
Acked-by: Stefan Agner <stefan@agner.ch>
Implementing the mtd_ooblayout_ops interface is the new way of exposing
ECC/OOB layout to MTD users.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Implementing the mtd_ooblayout_ops interface is the new way of exposing
ECC/OOB layout to MTD users.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Implementing the mtd_ooblayout_ops interface is the new way of exposing
ECC/OOB layout to MTD users.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Implementing the mtd_ooblayout_ops interface is the new way of exposing
ECC/OOB layout to MTD users.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Implementing the mtd_ooblayout_ops interface is the new way of exposing
ECC/OOB layout to MTD users.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Implementing the mtd_ooblayout_ops interface is the new way of exposing
ECC/OOB layout to MTD users.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Implementing the mtd_ooblayout_ops interface is the new way of exposing
ECC/OOB layout to MTD users.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Implementing the mtd_ooblayout_ops interface is the new way of exposing
ECC/OOB layout to MTD users.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Implementing the mtd_ooblayout_ops interface is the new way of exposing
ECC/OOB layout to MTD users.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Harvey Hunt <harvey.hunt@imgtec.com>
Implementing the mtd_ooblayout_ops interface is the new way of exposing
ECC/OOB layout to MTD users.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Implementing the mtd_ooblayout_ops interface is the new way of exposing
ECC/OOB layout to MTD users.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Han Xu <han.xu@nxp.com>
Tested-by: Han Xu <han.xu@nxp.com>
Now that mtd_ooblayout_ecc() returns the ECC byte position using the
OOB free method, we can get rid of the fsmc_nand_eccplace struct.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Implementing the mtd_ooblayout_ops interface is the new way of exposing
ECC/OOB layout to MTD users.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Implementing the mtd_ooblayout_ops interface is the new way of exposing
ECC/OOB layout to MTD users.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Implementing the mtd_ooblayout_ops interface is the new way of exposing
ECC/OOB layout to MTD users.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Implementing the mtd_ooblayout_ops interface is the new way of exposing
ECC/OOB layout to MTD users.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Implementing the mtd_ooblayout_ops interface is the new way of exposing
ECC/OOB layout to MTD users.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Implementing the mtd_ooblayout_ops interface is the new way of exposing
ECC/OOB layout to MTD users.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Implementing the mtd_ooblayout_ops interface is the new way of exposing
ECC/OOB layout to MTD users.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Implementing the mtd_ooblayout_ops interface is the new way of exposing
ECC/OOB layout to MTD users.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Implementing the mtd_ooblayout_ops interface is the new way of exposing
ECC/OOB layout to MTD users.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Implementing the mtd_ooblayout_ops interface is the new way of exposing
ECC/OOB layout to MTD users.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Implementing the mtd_ooblayout_ops interface is the new way of exposing
ECC/OOB layout to MTD users.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Implementing the mtd_ooblayout_ops interface is the new way of exposing
ECC/OOB layout to MTD users.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Implementing the mtd_ooblayout_ops interface is the new way of exposing
ECC/OOB layout to MTD users.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Replace the nand_ecclayout definition by the equivalent mtd_ooblayout_ops
definition.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Replace the default nand_ecclayout definitions for large and small page
devices with the equivalent mtd_ooblayout_ops.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Use the mtd_set_ecclayout() helper instead of directly assigning the
mtd->ecclayout field.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The mtd_ooblayout_xxx() helper functions have been added to avoid direct
accesses to ecclayout fields, and thus ease for future reworks.
Use these helpers in all places where the oobfree[] and eccpos[] arrays
where directly accessed.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Archit Taneja <architt@codeaurora.org>
The mtd_ooblayout_xxx() helper functions have been added to avoid direct
accesses to the ecclayout field, and thus ease for future reworks.
Use these helpers in all places where the oobfree[] and eccpos[] arrays
where directly accessed.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The mtd_ooblayout_xxx() helper functions have been added to avoid direct
accesses to the ecclayout field, and thus ease for future reworks.
Use these helpers in all places where the oobfree[] and eccpos[] arrays
where directly accessed.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The mtd_ooblayout_xxx() helper functions have been added to avoid direct
accesses to the ecclayout field, and thus ease for future reworks.
Use these helpers in all places where the oobfree[] and eccpos[] arrays
where directly accessed.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The mtd_ooblayout_xxx() helper functions have been added to avoid direct
accesses to the ecclayout field, and thus ease for future reworks.
Use these helpers in all places where the oobfree[] and eccpos[] arrays
where directly accessed.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The mtd_ooblayout_xxx() helper functions have been added to avoid direct
accesses to the ecclayout field, and thus ease for future reworks.
Use these helpers in all places where the oobfree[] and eccpos[] arrays
where directly accessed.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The mtd_ooblayout_xxx() helper functions have been added to avoid direct
accesses to the ecclayout field, and thus ease for future reworks.
Use these helpers in all places where the oobfree[] and eccpos[] arrays
where directly accessed.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Allow for NULL cur_offs values when the caller does not know where the
NAND page register pointer points to.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
sunxi_nfc_hw_ecc_read_chunk() always retrieves the ECC and protected free
bytes, no matter if the user really asked for it or not. This can take a
non negligible amount of time, especially on NAND chips exposing large OOB
areas (> 1KB). Make it optional.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
In order to support DMA operations in a clean way we need to extract some
of the logic coded in sunxi_nfc_hw_ecc_read/write_page() into their own
function.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Some NAND operations are so fast that it doesn't make any sense to use
interrupt based waits (the scheduling overhead is not worth it).
Rename sunxi_nfc_wait_int() into sunxi_nfc_wait_events() and add a
parameter to specify whether polling should be used or not.
Note that all sunxi_nfc_wait_int() are moved to the polling approach now,
but this should change as soon as we have more information about the
approximate time we are about to wait (can be extracted from the NAND
timings, and the type of operation).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
->dev_ready() is not supposed to wait for busy to ready solution (this is
the role of ->waitfunc()).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
When the NAND controller operates in DMA mode it can pipeline ECC
operations which improves the throughput.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
NFC_ECC_ERR_CNT() is not taking into account the case when the NAND chip
contains more than 4 ECC blocks (NANDs with 4kB+ pages).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
We don't need to manually toggle the CE line since the controller handles
it for us. Moreover, keeping the CE line low when interacting with a DDR
NAND can be problematic (data loss in some corner cases).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Try to pack address and command cycles into a single NAND controller
command to avoid polling the status register for each single change
on the NAND bus.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Being able to read subpages can greatly improve read performances if the
MTD user is only interested in a small section of a NAND page.
This is particularly true with large pages (>= 8k).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Allwinner's ECC engine is capable of protecting a few bytes of the OOB
area. Implement specific OOB functions to benefit from this capability.
Also, when in raw mode, the randomizer is disabled, which means you'll
only be able to retrieve randomized data, which is not really useful
for most applications.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Export the default read/write oob functions (for the standard and syndrome
scheme), so that drivers can use them for their raw implementation and
implement their own functions for the normal oob operation.
This is required if your ECC engine is capable of fixing some of the OOB
data. In this case you have to overload the ->read_oob() and ->write_oob(),
but if you don't specify the ->read/write_oob_raw() functions they are
assigned to the ->read/write_oob() implementation, which is not what you
want.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Adapt the NAND controller clk rate to the tWB, tADL, tWHR and tRHW
timings instead of returning an error when the maximum clk divisor is
not big enough to provide an appropriate timing.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The ONFI spec says that EDO should be enabled if the host drives tRC less
than 30ns, but the code just tests for the tRC_min value extracted from
the timings exposed by the NAND chip not the timings actually configured
in the NAND controller.
Fix that by first rounding down the requested clk_rate with
clk_round_rate() and then checking if tRC is actually smaller than 30ns.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Unlike what is specified in the Allwinner datasheets, the NAND clock rate
is not equal to 2/T but 1/T. Fix the clock rate selection accordingly.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
sunxi_nand_chip_set_timings() is extracting a pointer to the nfc from the
nand->controller field, but this field is initialized after
sunxi_nand_chip_set_timings() call.
Reorder the calls to avoid any problem.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The core now takes care of parsing generic DT properties in
nand_scan_ident() when nand_set_flash_node() has been called.
Rely on this initialization instead of calling of_get_nand_xxx()
manually.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
The core now takes care of parsing generic DT properties in
nand_scan_ident() when nand_set_flash_node() has been called.
Rely on this initialization instead of calling of_get_nand_xxx()
manually.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Nicolas Ferre <nicolas.ferre@atmel.com>
It also contains some minor related changes:
1) Don't warn if kzalloc fails as it dumps stack on its own
2) Use %pR format for displaying whole resource to avoid invalid format
warning
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The core now takes care of parsing generic DT properties in
nand_scan_ident() when nand_set_flash_node() has been called.
Rely on this initialization instead of calling of_get_nand_xxx()
manually.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
The core now takes care of parsing generic DT properties in
nand_scan_ident() when nand_set_flash_node() has been called.
Rely on this initialization instead of calling of_get_nand_xxx()
manually.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Tested-by: Franklin S Cooper Jr. <fcooper@ti.com>
Some drivers are including linux/of_mtd.h even if they don't use any of
the of_get_nand_xxx() helpers.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Harvey Hunt <harvey.hunt@imgtec.com>
If there is only one bit difference in the ECC, the function should
return 1.
The result of "diff0 & ~(1<<fls(diff0))" is equal to diff0, so the
function actually returns -1.
Signed-off-by: Zhaoxiu Zeng <zhaoxiu.zeng@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The new IFC controller version 2.0 has a different memory map page.
Upto IFC 1.4 PAGE size is 4 KB and from IFC2.0 PAGE size is 64KB.
This patch segregates the IFC global and runtime registers to appropriate
PAGE sizes.
Signed-off-by: Jaiprakash Singh <b44839@freescale.com>
Signed-off-by: Raghav Dogra <raghav@freescale.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Acked-by: Scott Wood <oss@buserror.net>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
There's no reason to BUG() when parameters are being
validated. Drivers can get things wrong, and it's much nicer
to just throw a noisy warn and fail gracefully, than calling
BUG() and throwing the whole system down the drain.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
fix the raw_buffer pointer double free issue found by coverify.
CID 18344 (#2 of 2): Double free (USE_AFTER_FREE)
3. double_free: Calling gpmi_alloc_dma_buffer frees pointer
this->raw_buffer which has already been freed
Signed-off-by: Han Xu <han.xu@nxp.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Document and match the brcm,brcmnand-v6.2 compatible string, the controller has
a register layout identical to the v6.0 version and supports prefetch. Update the
command shift logic to account for v6.2 controller which are the first ones to
use a shift of 0 (6.1 used a shift of 24).
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
bch->dev is already assigned to &pdev->dev in the probe function.
Remove the duplicate assignment done in jz4780_bch_get().
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Acked-by: Harvey Hunt <harvey.hunt@imgtec.com>
New atmel SoCs are able to fix bitflips in erased pages, but old ones
are still impacted by this problem. Use nand_check_erased_ecc_chunk() to
handle this case.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Herve Codina <herve.CODINA@celad.com>
Reviewed-by: Herve Codina <herve.CODINA@celad.com>
Tested-by: Herve Codina <herve.CODINA@celad.com>
This follows recent work on switching to enum nand_ecc_algo and
deprecating NAND_ECC_SOFT_BCH.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Use recently added of_get_nand_ecc_algo for that.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Pull leds-trigger changes from Jacek Anaszewski.
Create a generic mtd led-trigger to replace the exisitng nand led-trigger
implementation.
* 'mtd-nand-trigger' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
mtd: Hook I/O activity to the MTD LED trigger
mtd: nand: Remove the "nand-disk" LED trigger
leds: trigger: Introduce a MTD (NAND/NOR) trigger
mtd: Uninline mtd_write_oob and move it to mtdcore.c
leds: trigger: Introduce a kernel panic LED trigger
