Now q->now_rt is identical to q->now and is not required anymore.
Signed-off-by: Vasily Averin <vvs@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mainstream commit f0f6ee1f70 ("cbq: incorrect processing of high limits")
have side effect: if cbq bandwidth setting is less than real interface
throughput non-limited traffic can delay limited traffic for a very long time.
This happen because of q->now changes incorrectly in cbq_dequeue():
in described scenario L2T is much greater than real time delay,
and q->now gets an extra boost for each transmitted packet.
Accumulated boost prevents update q->now, and blocked class can wait
very long time until (q->now >= cl->undertime) will be true again.
To fix the problem the patch updates q->now on each cbq_update() call.
L2T-related pre-modification q->now was moved to cbq_update().
My testing confirmed that it fixes the problem and did not discover
any side-effects
Fixes: f0f6ee1f70 ("cbq: incorrect processing of high limits")
Signed-off-by: Vasily Averin <vvs@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The latest kernel fails to boot qemu arm images when using scsi
for disk access. Boot gets stuck after the following messages.
brd: module loaded
sym53c8xx 0000:00:0c.0: enabling device (0100 -> 0103)
sym0: <895a> rev 0x0 at pci 0000:00:0c.0 irq 93
sym0: No NVRAM, ID 7, Fast-40, LVD, parity checking
sym0: SCSI BUS has been reset.
scsi host0: sym-2.2.3
Bisect points to commit 71e75c97f9 ("scsi: convert device_busy to
atomic_t"). Code inspection shows the following suspicious change
in scsi_request_fn.
out_delay:
- if (sdev->device_busy == 0 && !scsi_device_blocked(sdev))
+ if (atomic_read(&sdev->device_busy) && !scsi_device_blocked(sdev))
blk_delay_queue(q, SCSI_QUEUE_DELAY);
}
'sdev->device_busy == 0' was replaced with 'atomic_read(&sdev->device_busy)',
meaning the logic was reversed. Changing this expression to
'!atomic_read(&sdev->device_busy)' fixes the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Jens Axboe <axboe@fb.com>
Reviewed-by: Venkatesh Srinivas <venkateshs@google.com>
Reviewed-by: Webb Scales <webbnh@hp.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch drops the userspace accessable sysfs entry for the maximum
datagram size of a 6LoWPAN fragment packet.
A fragment should not have a datagram size value greater than 1280 byte.
Instead of make this value configurable, we accept 1280 datagram size
fragment packets only.
Signed-off-by: Martin Townsend <martin.townsend@xsilon.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch changes the 1281 MTU to 1280. Others stack have only a 1280
byte array for uncompressed 6LoWPAN packets, this avoid that these
stacks have an overflow. Sending 1281 uncompressed 6LoWPAN packets isn't
also rfc complaint.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If received frame contains the reserved destination address mode. The
frame should be dropped and free the skb.
Signed-off-by: Martin Townsend <martin.townsend@xsilon.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch correct the return value of lowpan_alloc_frag if an error
occur. Errno numbers should always be negative.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch fix a memory leak if received frame was not able to parse.
Signed-off-by: Martin Townsend <martin.townsend@xsilon.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We did not check relocated directory in any way when processing Rock
Ridge 'CL' tag. Thus a corrupted isofs image can possibly have a CL
entry pointing to another CL entry leading to possibly unbounded
recursion in kernel code and thus stack overflow or deadlocks (if there
is a loop created from CL entries).
Fix the problem by not allowing CL entry to point to a directory entry
with CL entry (such use makes no good sense anyway) and by checking
whether CL entry doesn't point to itself.
CC: stable@vger.kernel.org
Reported-by: Chris Evans <cevans@google.com>
Signed-off-by: Jan Kara <jack@suse.cz>
We have released the ->i_data_sem before invoking udf_add_entry(),
so in following error path, we should not release this lock again.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Mika has done great work in that field, so let people know.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The SMBus host controller is the same as used in Baytrail so add the new
PCI ID to the driver's list of supported IDs.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit da3c6647(I2C/ACPI: Clean up I2C ACPI code and Add CONFIG_I2C_ACPI
config) adds a new kernel config I2C_ACPI and make I2C core built in
when the config is selected. This is wrong because distributions
etc generally compile I2C as a module and the commit broken that.
This patch is to rename I2C_ACPI to ACPI_I2C_OPREGION. New config
only controls ACPI I2C operation region code and depends on I2C=y.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[wsa: removed unrelated change for Kconfig]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
- raid6 data corruption during recovery
- raid6 livelock
- raid10 memory leaks.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=Pi8y
-----END PGP SIGNATURE-----
Merge tag 'md/3.17-fixes' of git://neil.brown.name/md
Pull md bugfixes from Neil Brown:
"Here are the bug-fixes I promised :-)
Funny how you start looking for one and other start appearing.
- raid6 data corruption during recovery
- raid6 livelock
- raid10 memory leaks"
* tag 'md/3.17-fixes' of git://neil.brown.name/md:
md/raid10: always initialise ->state on newly allocated r10_bio
md/raid10: avoid memory leak on error path during reshape.
md/raid10: Fix memory leak when raid10 reshape completes.
md/raid10: fix memory leak when reshaping a RAID10.
md/raid6: avoid data corruption during recovery of double-degraded RAID6
md/raid5: avoid livelock caused by non-aligned writes.
Three more commits needed for v3.17: A bug fix for reserved regions
based at address zero, a clarification on how to interpret existence of
both interrupts and interrupts-extended properties, and a fix to allow
device tree testcases to run on any platform.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ZaXA
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux
Pull devicetree fixes from Grant Likely:
"Three more commits needed for v3.17: A bug fix for reserved regions
based at address zero, a clarification on how to interpret existence
of both interrupts and interrupts-extended properties, and a fix to
allow device tree testcases to run on any platform"
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux:
of/irq: Fix lookup to use 'interrupts-extended' property first
Enabling OF selftest to run without machine's devicetree
of: Allow mem_reserve of memory with a base address of zero
As a generic function, deassign_guest_irq() assumes it can be called
even if assign_guest_irq() is not be called successfully (which can be
triggered by ioctl from user mode, indirectly).
So for assign_guest_irq() failure process, need set 'dev->irq_source_id'
to -1 after free 'dev->irq_source_id', or deassign_guest_irq() may free
it again.
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This reverts commit 682367c494,
which causes 32-bit SMP Windows 7 guests to panic.
SeaBIOS has a limit on the number of MTRRs that it can handle,
and this patch exceeded the limit. Better revert it.
Thanks to Nadav Amit for debugging the cause.
Cc: stable@nongnu.org
Reported-by: Wanpeng Li <wanpeng.li@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This reverts the check added by commit 5045b46803 (KVM: x86: check CS.DPL
against RPL during task switch, 2014-05-15). Although the CS.DPL=CS.RPL
check is mentioned in table 7-1 of the SDM as causing a #TSS exception,
it is not mentioned in table 6-6 that lists "invalid TSS conditions"
which cause #TSS exceptions. In fact it causes some tests to fail, which
pass on bare-metal.
Keep the rest of the commit, since we will find new uses for it in 3.18.
Reported-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit d40a6898e5 mistakenly caused instructions which are not marked as
EmulateOnUD to be emulated upon #UD exception. The commit caused the check of
whether the instruction flags include EmulateOnUD to never be evaluated. As a
result instructions whose emulation is broken may be emulated. This fix moves
the evaluation of EmulateOnUD so it would be evaluated.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
[Tweak operand order in &&, remove EmulateOnUD where it's now superfluous.
- Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
fc95ca7284 claims that there is no
functional change but this is not true as it calls get_order() (which
takes bytes) where it should have called order_base_2() and the kernel
stops on VM_BUG_ON().
This replaces get_order() with order_base_2() (round-up version of ilog2).
Suggested-by: Paul Mackerras <paulus@samba.org>
Cc: Alexander Graf <agraf@suse.de>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The third parameter of kvm_iommu_put_pages is wrong,
It should be 'gfn - slot->base_gfn'.
By making gfn very large, malicious guest or userspace can cause kvm to
go to this error path, and subsequently to pass a huge value as size.
Alternatively if gfn is small, then pages would be pinned but never
unpinned, causing host memory leak and local DOS.
Passing a reasonable but large value could be the most dangerous case,
because it would unpin a page that should have stayed pinned, and thus
allow the device to DMA into arbitrary memory. However, this cannot
happen because of the condition that can trigger the error:
- out of memory (where you can't allocate even a single page)
should not be possible for the attacker to trigger
- when exceeding the iommu's address space, guest pages after gfn
will also exceed the iommu's address space, and inside
kvm_iommu_put_pages() the iommu_iova_to_phys() will fail. The
page thus would not be unpinned at all.
Reported-by: Jack Morgenstein <jackm@mellanox.com>
Cc: stable@vger.kernel.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Valleyview and Cherryview have the same behavior on display audio. So this patch
defines is_valleyview_plus() to include codecs for both Valleyview and its successor
Cherryview, and apply Valleyview fix-ups to Cherryview.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Both Haswell and Broadwell need set depop_delay to 0. So apply this
setting to haswell plus.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Most places which allocate an r10_bio zero the ->state, some don't.
As the r10_bio comes from a mempool, and the allocation function uses
kzalloc it is often zero anyway. But sometimes it isn't and it is
best to be safe.
I only noticed this because of the bug fixed by an earlier patch
where the r10_bios allocated for a reshape were left around to
be used by a subsequent resync. In that case the R10BIO_IsReshape
flag caused problems.
Signed-off-by: NeilBrown <neilb@suse.de>
When a raid10 commences a resync/recovery/reshape it allocates
some buffer space.
When a resync/recovery completes the buffer space is freed. But not
when the reshape completes.
This can result in a small memory leak.
There is a subtle side-effect of this bug. When a RAID10 is reshaped
to a larger array (more devices), the reshape is immediately followed
by a "resync" of the new space. This "resync" will use the buffer
space which was allocated for "reshape". This can cause problems
including a "BUG" in the SCSI layer. So this is suitable for -stable.
Cc: stable@vger.kernel.org (v3.5+)
Fixes: 3ea7daa5d7
Signed-off-by: NeilBrown <neilb@suse.de>
raid10 reshape clears unwanted bits from a bio->bi_flags using
a method which, while clumsy, worked until 3.10 when BIO_OWNS_VEC
was added.
Since then it clears that bit but shouldn't. This results in a
memory leak.
So change to used the approved method of clearing unwanted bits.
As this causes a memory leak which can consume all of memory
the fix is suitable for -stable.
Fixes: a38352e0ac
Cc: stable@vger.kernel.org (v3.10+)
Reported-by: mdraid.pkoch@dfgh.net (Peter Koch)
Signed-off-by: NeilBrown <neilb@suse.de>
On some HP laptops, the mute led is controlled by codec gpio.
When some machine resume from s3/s4, the codec gpio data will be
cleared to 0 by BIOS:
Before suspend:
IO[3]: enable=1, dir=1, wake=0, sticky=0, data=1, unsol=0
After resume:
IO[3]: enable=1, dir=1, wake=0, sticky=0, data=0, unsol=0
To skip the AFG node to enter D3 can't fix this problem.
A workaround is to restore the gpio data when the system resume
back from s3/s4. It is safe even on the machines without this
problem.
BugLink: https://bugs.launchpad.net/bugs/1358116
Tested-by: Franz Hsieh <franz.hsieh@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Crucial M550 may cause data corruption on queued trims and is
blacklisted. The pattern used for it fails to match 1TB one as the
capacity section will be four chars instead of three. Widen the
pattern.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Charles Reiss <woggling@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=81071
Cc: stable@vger.kernel.org
Commit 9183df25fe ("shm: add memfd_create() syscall") added a new
system call (memfd_create) but didn't update the asm-generic unistd
header.
This patch adds the new system call to the asm-generic version of
unistd.h so that it can be used by architectures such as arm64.
Cc: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
arch/arm/ just grew support for the new memfd_create and getrandom
syscalls, so add them to our compat layer too.
Signed-off-by: Will Deacon <will.deacon@arm.com>
This removes an unfortunately placed semi-colon resulting in all instruction
caches being classified as AIVIVT.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When multiple devices are detached in __detach_device, they
are also removed from the domains dev_list. This makes it
unsafe to use list_for_each_entry_safe, as the next pointer
might also not be in the list anymore after __detach_device
returns. So just repeatedly remove the first element of the
list until it is empty.
Cc: stable@vger.kernel.org
Tested-by: Marti Raudsepp <marti@juffo.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
When the BUS_NOTIFY_DEL_DEVICE event is received the device
might still be attached to a driver. In this case the domain
can't be released as the mappings might still be in use.
Defer the domain removal in this case until we receivce the
BUS_NOTIFY_UNBOUND_DRIVER event.
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: stable@vger.kernel.org # v3.15, v3.16
Signed-off-by: Joerg Roedel <jroedel@suse.de>
During recovery of a double-degraded RAID6 it is possible for
some blocks not to be recovered properly, leading to corruption.
If a write happens to one block in a stripe that would be written to a
missing device, and at the same time that stripe is recovering data
to the other missing device, then that recovered data may not be written.
This patch skips, in the double-degraded case, an optimisation that is
only safe for single-degraded arrays.
Bug was introduced in 2.6.32 and fix is suitable for any kernel since
then. In an older kernel with separate handle_stripe5() and
handle_stripe6() functions the patch must change handle_stripe6().
Cc: stable@vger.kernel.org (2.6.32+)
Fixes: 6c0069c0ae
Cc: Yuri Tikhonov <yur@emcraft.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Reported-by: "Manibalan P" <pmanibalan@amiindia.co.in>
Tested-by: "Manibalan P" <pmanibalan@amiindia.co.in>
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1090423
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
If a stripe in a raid6 array received a write to each data block while
the array is degraded, and if any of these writes to a missing device
are not page-aligned, then a live-lock happens.
In this case the P and Q blocks need to be read so that the part of
the missing block which is *not* being updated by the write can be
constructed. Due to a logic error, these blocks are not loaded, so
the update cannot proceed and the stripe is 'handled' repeatedly in an
infinite loop.
This bug is unlikely as most writes are page aligned. However as it
can lead to a livelock it is suitable for -stable. It was introduced
in 3.16.
Cc: stable@vger.kernel.org (v3.16)
Fixed: 67f455486d
Signed-off-by: NeilBrown <neilb@suse.de>
fallocate -z (FALLOC_FL_ZERO_RANGE) can map to SMB3
FSCTL_SET_ZERO_DATA SMB3 FSCTL but FALLOC_FL_ZERO_RANGE
when called without the FALLOC_FL_KEEPSIZE flag set could want
the file size changed so we can not support that subcase unless
the file is cached (and thus we know the file size).
Signed-off-by: Steve French <smfrench@gmail.com>
Reviewed-by: Pavel Shilovsky <pshilovsky@samba.org>
Implement FALLOC_FL_PUNCH_HOLE (which does not change the file size
fortunately so this matches the behavior of the equivalent SMB3
fsctl call) for SMB3 mounts. This allows "fallocate -p" to work.
It requires that the server support setting files as sparse
(which Windows allows).
Signed-off-by: Steve French <smfrench@gmail.com>
When the server (for an SMB2 or SMB3 mount) doesn't support
an ioctl (such as setting the compressed flag
on a file) we were incorrectly returning EIO instead
of EOPNOTSUPP, this is confusing e.g. doing chattr +c to a file
on a non-btrfs Samba partition, now the error returned is more
intuitive to the user. Also fixes error mapping on setting
hardlink to servers which don't support that.
Signed-off-by: Steve French <smfrench@gmail.com>
Reviewed-by: David Disseldorp <ddiss@suse.de>
Before this patch, the driver included <linux/tegra-powergate.h>,
which was effectively renamed to <soc/tegra/pmc.h> at about the same
time the ahci_tegra series landed. Fix the include path so that the
driver compiles.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Change return type to signed int since it could be
a negative errno.
Signed-off-by: Arjun Sreedharan <arjun024@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch removes the NCQ support from the APM X-Gene SoC AHCI
Host Controller driver as it doesn't support it.
Signed-off-by: Loc Ho <lho@apm.com>
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
When we requests rename we also need to update attributes
of both source and target parent directories. Not doing it
causes generic/309 xfstest to fail on SMB2 mounts. Fix this
by marking these directories for force revalidating.
Cc: <stable@vger.kernel.org>
Signed-off-by: Pavel Shilovsky <pshilovsky@samba.org>
Signed-off-by: Steve French <smfrench@gmail.com>
SMB2 servers indicates the end of a directory search with
STATUS_NO_MORE_FILE error code that is not processed now.
This causes generic/257 xfstest to fail. Fix this by triggering
the end of search by this error code in SMB2_query_directory.
Also when negotiating CIFS protocol we tell the server to close
the search automatically at the end and there is no need to do
it itself. In the case of SMB2 protocol, we need to close it
explicitly - separate close directory checks for different
protocols.
Cc: <stable@vger.kernel.org>
Signed-off-by: Pavel Shilovsky <pshilovsky@samba.org>
Signed-off-by: Steve French <smfrench@gmail.com>
As Raphael Geissert pointed out, tcon_error_exit can dereference tcon
and there is one path in which tcon can be null.
Signed-off-by: Steve French <smfrench@gmail.com>
CC: Stable <stable@vger.kernel.org> # v3.7+
Reported-by: Raphael Geissert <geissert@debian.org>
