This patch adds driver hooks to implement ndo_ops to add/del
udp port in the HW to identify GENEVE tunnels.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When in NAPI with interrupts disabled, the HW needs to be forced to do a
write back on TX if the number of descriptors pending are less than a
cache line.
This stat helps keep track of how many times we get into this situation.
Change-ID: I76c1bcc7ebccd6bffcc5aa33bfe05f2fa1c9a984
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The adaptive ITR (interrupt throttle rate) algorithm was adjusting
the hardware's interrupt rate too frequently. This caused a lot
of variation in the interrupt rate for fairly constant workloads.
Change the code to have a counter and adjust only once every N
number of interrupts.
Change-ID: I0460f1f86571037484eca5aca36ac4d889cb8389
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The dynamic algorithm, while now working, doesn't have good
performance in 40G mode.
One part of this patch addresses the high CPU utilization of some small
streaming workloads that the driver should reduce CPU in.
It also changes the minimum ITR that the dynamic algorithm
will settle on, causing our minimum latency to go from 12us
to about 14us, when using adaptive mode.
It also changes the BULK interrupt rate to allow maximum throughput
on a 40Gb connection with a single thread of transmit, clamping
interrupt rate to 8000 for TX makes single thread traffic go too
slow.
The new ULTRA bulk setting is introduced and is used
when the Rx packet rate on this queue exceeds 40000 packets per
second. This value of 40000 was chosen because the automatic tuning
of minimum ITR=20us means that a single queue can't quite achieve
that many packets per second from a round-robin test.
Change-ID: Icce8faa128688ca5fd2c4229bdd9726877a92ea2
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The XL710 hardware has a different interrupt moderation design
that can support a limit of total interrupts per second per
vector, in addition to the "number of interrupts per second"
controls already established in the driver. This combination
of hardware features allows us to set very low default latency
settings but minimize the total CPU utilization by not
making too many interrupts, should the user desire.
The current driver implementation is still enabling the dynamic
moderation in the driver, and only using the rx/tx-usecs
limit in ethtool to limit the interrupt rate per second, by default.
The new code implemented in this patch
2) adds init/use of the new "Interrupt Limit" register
3) adds ethtool knob to control/report the limits above
Usage is ethtool -C ethx rx-usecs-high <value> Where <value> is number
of microseconds to create a rate of 1/N interrupts per second,
regardless of rx-usecs or tx-usecs values. Since there is a credit based
scheme in the hardware, the rx-usecs and tx-usecs can be configured for
very low latency for short bursts, but once the credit runs out the
refill rate on the credits is limited by rx-usecs-high.
Change-ID: I3a1075d3296123b0f4f50623c779b027af5b188d
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add missings spaces after declarations, remove another __func__ use,
remove uncessary braces, remove unneeded breaks, and useless returns,
and generally fix up some code.
Change-ID: Ie715d6b64976c50e1c21531685fe0a2bd38c4244
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Keep track of how many times we ask the stack to linearize the
skb because the HW cannot handle skbs with more than 8 frags per
segment/single packet.
Change-ID: If455452060963a769bbe6112cba952e79e944b52
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sparse found some issues with 32 bit compilation, which probably should
at least work without warning. Not only that, but the code was wrong.
Thanks sparse!!
And thanks to the kbuild robot zero day testing for finding this issue.
$ make ARCH=i386 M=drivers/net/ethernet/intel/i40e C=2 CF="-D__CHECK_ENDIAN__"
CHECK drivers/net/ethernet/intel/i40e/i40e_main.c
include/linux/etherdevice.h:79:32: warning: restricted __be16 degrades to integer
drivers/net/ethernet/intel/i40e/i40e_main.c:7565:17: warning: shift too big (32) for type unsigned long
drivers/net/ethernet/intel/i40e/i40e_main.c:7565:17: warning: shift too big (42) for type unsigned long
drivers/net/ethernet/intel/i40e/i40e_main.c:7565:17: warning: shift too big (39) for type unsigned long
drivers/net/ethernet/intel/i40e/i40e_main.c:7565:17: warning: shift too big (40) for type unsigned long
CC: kbuild-all@01.org
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the issue of forcing WB too often causing us to not
benefit from NAPI.
Without this patch we were forcing WB/arming interrupt too often taking
away the benefits of NAPI and causing a performance impact.
With this patch we disable force WB in the clean routine for X710
and XL710 adapters. X722 adapters do not enable interrupt to force
a WB and benefit from WB_ON_ITR and hence force WB is left enabled
for those adapters.
For XL710 and X710 adapters if we have less than 4 packets pending
a software Interrupt triggered from service task will force a WB.
This patch also changes the conditions for setting RS bit as described
in code comments. This optimizes when the HW does a tail bump and when
it does a WB. It also optimizes when we do a wmb.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch modifies the driver timeout logic by issuing a writeback
request via a software interrupt to the hardware the first time the
driver detects a hang. The driver was too aggressive in resetting a hung
queue, so back that off by removing logic to down the netdevice after
too many hangs, and move the function to the service task.
Change-ID: Ife100b9d124cd08cbdb81ab659008c1b9abbedea
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e_get_head needs to be called in multiple files in a further patch,
prepare by moving the function into a header file.
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 supports offloading of outer UDP TX and RX checksum for tunneled
packets. This patch exposes the support and leaves it enabled by
default.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 fixes an issue from X710 where TX descriptor WB would not happen if
the interrupts were disabled. In order for the write backs to happen a
bit needs to be set in the dynamic interrupt control register called
WB_ON_ITR. With this feature, the SW driver need not arm SW interrupts to
work around the issue in X710.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 uses the admin queue to configure RSS. This patch adds the necessary
flow changes to configure RSS through AQ. It also adds the separate VMDQ2
lookup tables and hash key programming for X722.
X722 also exposes a different set of PCTYPES for RSS, this patch
accommodates those changes.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use macros for abstracting (1 << foo) to BIT(foo)
and (1ULL << foo64) to BIT_ULL(foo64) in order to match
better with kernel requirements.
NOTE: the adminq_cmd.h file was not modified on purpose because
of the dependency upon firmware for that file.
Change-ID: I73ee2e48c880d671948aad19bd53ca6b2ac558fc
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver doesn't use the time_stamp member to determine if there is a
tx_hang any more. There really isn't any point to the variable at all
so just remove it. It was left over from a previous tx_hang design.
Change-ID: I4c814827e1bcb46e45118fe37acdcfa814fb62a0
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Without this, RSS would have done inner header load balancing. Now we can
get the benefits of ATR for tunneled packets to better align TX and RX
queues with the right core/interrupt.
Change-ID: I07d0e0a192faf28fdd33b2f04c32b2a82ff97ddd
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
drivers/net/ethernet/rocker/rocker.c
The rocker commit was two overlapping changes, one to rename
the ->vport member to ->pport, and another making the bitmask
expression use '1ULL' instead of plain '1'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware has some limitations the driver needs to adhere to,
that we found in extended testing.
1) no more than 8 descriptors per packet on the wire
2) no header can span more than 3 descriptors
If one of these events occurs, the hardware will generate an internal
error and freeze the Tx queue.
This patch linearizes the skb to avoid these situations.
Change-ID: I37dab7d3966e14895a9663ec4d0aaa8eb0d9e115
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Split the receive hot path code into two, one for packet split and one
for single buffer. This improves receive performance since we only need
to check if the ring is in packet split mode once per NAPI poll time,
not several times per packet. The single buffer code is further improved
by the removal of a bunch of code and several variables that are not
needed. On a receive-oriented test this can improve single-threaded
throughput.
Also refactor the packet split receive path to use a fixed buffer for
headers, like ixgbe does. This vastly reduces the number of DMA mappings
and unmappings we need to do, allowing for much better performance in
the presence of an IOMMU.
Lastly, correct packet split descriptor types now that we are actually
using them.
Change-ID: I3a194a93af3d2c31e77ff17644ac7376da6f3e4b
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the driver was polling with interrupts disabled the hardware
will occasionally not write back descriptors. This patch causes
the driver to detect this situation and force an interrupt to
fire which will flush the stuck descriptor. Does not conflict
with napi because if we are already polling the napi_schedule is
ignored. Additionally the extra interrupts are rate limited, so
don't cause a burden to the CPU.
Change-ID: Iba4616d2a71288672a5f08e4512e2704b97335e8
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The interrupt throttle rate minimum is actually 2us, so
fix that define and while we are there, remove some unused defines.
Change some strings in the function to be a bit less wrappy, and
express the correct limits.
Change-ID: I96829bbc77935e0b57c6f0fc1439fb4152b2960a
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We are seeing situations where the driver sees a hang with less than 4
desc pending, if the driver chooses to ignore it the queue progresses
forward and the stack never experiences a real hang.
With this patch we will log a stat when this situation happens
"tx_sluggish" will increment and we can see some more details
at a higher debug level. Other than that we will ignore this
particular case of Tx hang.
Change-ID: I7d1d1666d990e2b12f4f6bed0d17d22e1b6410d5
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Adds FCoE specific code to existing i40e core driver to:-
1. have separate FCoE VSI with additional FCoE queues pairs.
2. have FCoE related hash defines.
3. have additional FCoE related stats code.
4. export and then re-use existing functions required by FCoE build.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Jack Morgan<jack.morgan@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The HW still needs to consume it and freeing it in the function
that created it would mean we will be racing with the HW. The
i40e_clean_tx_ring() routine will free up the buffer attached once
the HW has consumed it. The clean_fdir_tx_irq function had to be fixed
to handle the freeing correctly.
Cases where we program more than one filter per flow (Ipv4), the
code had to be changed to allocate dummy buffer multiple times
since it will be freed by the clean routine. This also fixes an issue
where the filter program routine was not checking if there were
descriptors available for programming a filter.
Change-ID: Idf72028fd873221934e319d021ef65a1e51acaf7
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
One of the PCTYPES that was moved to a reserved value
wasn't removed from the code.
Change-ID: I31fafe6d79c5f5128179979af5eaafa8c0cd62fe
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The TSO logic in the transmit path had some assumptions that
have been broken now that the kernel can send as much as 32kB
in a single skb->frag[.] entry, even on a system with 4kB pages.
This fixes the assumptions and allows the kernel to operate
as efficiently as possible with both SENDFILE and SEND.
In addition, the hardware limit of data contained in a descriptor is
changed to the next power of two below where it currently is in
order to align to a power of two value, preventing a single byte
of data in a descriptor.
Change-ID: I6af1f0b87c1458e10644dbd47541591075a52651
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove unused defines and macros for RX_LRO.
Change-ID: I8ca6715edfa62b56837417a1c4ff68c2345dab6e
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The storm control features are not part of the hardware
and mistakenly were left in the code. Remove them as
they are not needed any more.
Change-ID: I6e9277c8da2c52e69348a657bae25271449c2099
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Patch to remove PCTYPE definitions which are now reserved.
Change-ID: I66c1c16a45a16f4894b2983101ab2a48ce03f1f4
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
New feature: Enable PTP support in the i40e driver.
Change-ID: I6a8e799f582705191f9583afb1b9231a8db96cc8
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set the ITR max and min values to match the hardware max value
and the recommended min value. These values are shifted right
one bit because the register counts in 2 usec units, so leave
a comment to explain.
Change-ID: I289c27955cf6c566a6d21b95c3110b88cbb15dad
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The alloc_rx_buff_failed and alloc_rx_page_failed variables
are both part of an rx specific structure so just remove
the _rx part of the name. No functional changes.
Change-ID: Icffa2f5d13c6f2b1e09cf45b9472b83c9dae8fc6
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The GPL header included in each file in the i40e driver doesn't
need to include the "this program" text since this driver
is already part of the larger kernel.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add an include header guard to guard against multiple includes
Change-Id: I73efa03efc912d2047edab903c7caed05b444da2
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make a define used in the header file by both VF and PF drivers.
Change-Id: Ie9e35adcc021cd6a8f7513934984eb4ed55774f5
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
I40E_ITR_NONE was being used as an ITRN register index by
accident because it was easily associated with the I40E_RX_ITR
and friends defines.
Change the name slightly in order to make it clear that
I40E_ITR_NONE is really associated with the DYN_CTL register
sets.
Change-Id: I04702c027c7495b90a8bf2db85d3e085a2c7d02a
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change brings support for 64 bit netstats to the driver. Previously
the stats were 64 bit but highly racy due to the fact that 64 bit
transactions are not atomic on 32 bit systems. This change makes is so
that the 64 bit byte and packet stats are reliable on all architectures.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allocate the queue pairs individually instead of as a group. This
allows for much easier queue management as it is possible to dynamically
resize the queues without having to free and allocate the entire block.
Ease statistic collection by treating Tx/Rx queue pairs as a single
unit. Each pair is allocated together and starts with a Tx queue and
ends with an Rx queue. By ordering them this way it is possible to know
the Rx offset based on a pointer to the Tx queue.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This replaces the ring container array with a linked list. The idea is
to make the logic much easier to deal with since this will allow us to
call a simple helper function from the q_vectors to go through the
entire list.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This makes it so that the Tx and Rx byte and packet counts are
separated from the rest of the statistics. This allows for better
isolation of these stats when we move them into the 64 bit statistics.
Simplify things by re-ordering how the stats display in ethtool.
Instead of displaying all of the Tx queues as a block, followed by all
the Rx queues, the new order is Tx[0], Rx[0], Tx[1], Rx[1], ..., Tx[n],
Rx[n]. This reduces the loops and cleans up the display for testing
purposes since it is very easy to verify if flow director is doing the
right thing as the Tx and Rx queue pair are shown in pairs.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Drop Tx flag and TXSW which is tested but never set.
As a result of this change we can drop a complicated check that always
resulted in the final result of i40e_tx_csum being equal to the
CHECKSUM_PARTIAL value. As such we can replace the entire function call
with just a check for skb->summed == CHECKSUM_PARTIAL.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sync the fast path for i40e_tx_map and i40e_clean_tx_irq so that they
are similar to igb and ixgbe.
- Only update the Tx descriptor ring in tx_map
- Make skb mapping always on the first buffer in the chain
- Drop the use of MAPPED_AS_PAGE Tx flag
- Only store flags on the first buffer_info structure
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
- drop the mapped_as_page u8 from the Tx buffer info as it was unused
- use the DMA unmap accessors for Tx DMA
- replace checks of DMA with checks of the unmap length to verify if an
unmap is needed
- update the Tx buffer layout to make it consistent with igb, ixgbe
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The Tx "completed" stat was part of the original rewrite for detecting
Tx hangs. However some time ago in ixgbe I determined that we could
just use the packets stat instead. Since then this stat was
removed from ixgbe and it serves no purpose in i40e so it can be
dropped.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch contains the main driver header files, containing
structures and data types specific to the linux driver.
i40e_osdep.h contains some code that helps us adapt our OS agnostic code to
Linux.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
CC: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
CC: e1000-devel@lists.sourceforge.net
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
