This patch adds usart dma definitions to both dtsi for sam9x5 chips. Without
usage of dma it's unable to catch all bytes on usart receiver.
Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Another week, another small batch of fixes.
Most of these make zynq, socfpga and sunxi platforms work a bit
better:
* Due to new requirements for regulators, DWMMC on socfpga broke past 3.17.
* SMP spinup fix for socfpga
* A few DT fixes for zynq
* Another option (FIXED_REGULATOR) for sunxi is needed that used to be selected
by other options but no longer is.
* A couple of small DT fixes for at91
* ...and a couple for i.MX.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=MTvh
-----END PGP SIGNATURE-----
Merge tag 'armsoc-for-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Another week, another small batch of fixes.
Most of these make zynq, socfpga and sunxi platforms work a bit
better:
- due to new requirements for regulators, DWMMC on socfpga broke past
v3.17
- SMP spinup fix for socfpga
- a few DT fixes for zynq
- another option (FIXED_REGULATOR) for sunxi is needed that used to
be selected by other options but no longer is.
- a couple of small DT fixes for at91
- ...and a couple for i.MX"
* tag 'armsoc-for-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: imx28-evk: Let i2c0 run at 100kHz
ARM: i.MX6: Fix "emi" clock name typo
ARM: multi_v7_defconfig: enable CONFIG_MMC_DW_ROCKCHIP
ARM: sunxi_defconfig: enable CONFIG_REGULATOR_FIXED_VOLTAGE
ARM: dts: socfpga: Add a 3.3V fixed regulator node
ARM: dts: socfpga: Fix SD card detect
ARM: dts: socfpga: rename gpio nodes
ARM: at91/dt: sam9263: fix PLLB frequencies
power: reset: at91-reset: fix power down register
MAINTAINERS: add atmel ssc driver maintainer entry
arm: socfpga: fix fetching cpu1start_addr for SMP
ARM: zynq: DT: trivial: Fix mc node
ARM: zynq: DT: Add cadence watchdog node
ARM: zynq: DT: Add missing reference for memory-controller
ARM: zynq: DT: Add missing reference for ADC
ARM: zynq: DT: Add missing address for L2 pl310
ARM: zynq: DT: Remove 222 MHz OPP
ARM: zynq: DT: Fix GEM register area size
- Revert one patch which increases I2C bus frequency on imx28-evk
- Fix a typo on imx6q EIM clock name
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUTE8JAAoJEFBXWFqHsHzOGawH/0KGNaHbI3rj+Hx1HHtN056y
3rgHSsLZSLQB89+bMd8aEVPJ2z0RKYXfyI1IvkcgEZxsqmHwRY8Fwlof4D38/bfP
tRHnyzT2E+znnyhvUZlH9yd9foTd3VkXbxFxbEssRHl2W2OxA0+3MbskknERPZqs
qr22DcMLKyrTbUH39iiEjS43qcJhuf/6vZmoVGCGdZonZwkH8WccIQ+kKneOn8/Z
11U4ioB4pirqvhM1niYQ95RLG0TveBN6op3c1HWkhqY4EKOlraZHQb4EOoslSO/X
vWoJqgB9DLH3eV+WTFI0FjGDK/6CFhgAth8q0FKVlHA3FFHr+fXdxv/+NLtagzQ=
=elO/
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
Merge "ARM: imx: fixes for 3.18" from Shawn Guo:
The i.MX fixes for 3.18:
- Revert one patch which increases I2C bus frequency on imx28-evk
- Fix a typo on imx6q EIM clock name
* tag 'imx-fixes-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx28-evk: Let i2c0 run at 100kHz
ARM: i.MX6: Fix "emi" clock name typo
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit 78b81f4666 ("ARM: dts: imx28-evk: Run I2C0 at 400kHz") caused issues
when doing the following sequence in loop:
- Boot the kernel
- Perform audio playback
- Reboot the system via 'reboot' command
In many times the audio card cannot be probed, which causes playback to fail.
After restoring to the original i2c0 frequency of 100kHz there is no such
problem anymore.
This reverts commit 78b81f4666.
Cc: <stable@vger.kernel.org> # 3.16+
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Fix a typo error, the "emi" names refer to the eim clocks.
The change fixes typo in EIM and EIM_SLOW pre-output dividers and
selectors clock names. Notably EIM_SLOW clock itself is named correctly.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
[vladimir_zapolskiy@mentor.com: ported to v3.17]
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Pull MIPS fixes from Ralf Baechle:
"This is the first round of fixes and tying up loose ends for MIPS.
- plenty of fixes for build errors in specific obscure configurations
- remove redundant code on the Lantiq platform
- removal of a useless SEAD I2C driver that was causing a build issue
- fix an earlier TLB exeption handler fix to also work on Octeon.
- fix ISA level dependencies in FPU emulator's instruction decoding.
- don't hardcode kernel command line in Octeon software emulator.
- fix an earlier fix for the Loondson 2 clock setting"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: SEAD3: Fix I2C device registration.
MIPS: SEAD3: Nuke PIC32 I2C driver.
MIPS: ftrace: Fix a microMIPS build problem
MIPS: MSP71xx: Fix build error
MIPS: Malta: Do not build the malta-amon.c file if CMP is not enabled
MIPS: Prevent compiler warning from cop2_{save,restore}
MIPS: Kconfig: Add missing MIPS_CPS dependencies to PM and cpuidle
MIPS: idle: Remove leftover __pastwait symbol and its references
MIPS: Sibyte: Include the swarm subdir to the sb1250 LittleSur builds
MIPS: ptrace.h: Add a missing include
MIPS: ath79: Fix compilation error when CONFIG_PCI is disabled
MIPS: MSP71xx: Remove compilation error when CONFIG_MIPS_MT is present
MIPS: Octeon: Remove special case for simulator command line.
MIPS: tlbex: Properly fix HUGE TLB Refill exception handler
MIPS: loongson2_cpufreq: Fix CPU clock rate setting mismerge
pci: pci-lantiq: remove duplicate check on resource
MIPS: Lasat: Add missing CONFIG_PROC_FS dependency to PICVUE_PROC
MIPS: cp1emu: Fix ISA restrictions for cop1x_op instructions
- Enable 48-bit VA space now that KVM has been fixed, together with
a couple of fixes for pgd allocation alignment and initial memblock
current_limit. There is still a dependency on !ARM_SMMU which needs to
be updated as it uses the page table manipulation macros of the host
kernel
- eBPF fixes following changes/conflicts during the merging window
- Compat types affecting compat_elf_prpsinfo
- Compilation error on UP builds
- ASLR fix when /proc/sys/kernel/randomize_va_space == 0
- DT definitions for CLCD support on ARMv8 model platform
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=QssH
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- enable 48-bit VA space now that KVM has been fixed, together with a
couple of fixes for pgd allocation alignment and initial memblock
current_limit. There is still a dependency on !ARM_SMMU which needs
to be updated as it uses the page table manipulation macros of the
host kernel
- eBPF fixes following changes/conflicts during the merging window
- Compat types affecting compat_elf_prpsinfo
- Compilation error on UP builds
- ASLR fix when /proc/sys/kernel/randomize_va_space == 0
- DT definitions for CLCD support on ARMv8 model platform
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Fix memblock current_limit with 64K pages and 48-bit VA
arm64: ASLR: Don't randomise text when randomise_va_space == 0
arm64: vexpress: Add CLCD support to the ARMv8 model platform
arm64: Fix compilation error on UP builds
Documentation/arm64/memory.txt: fix typo
net: bpf: arm64: minor fix of type in jited
arm64: bpf: add 'load 64-bit immediate' instruction
arm64: bpf: add 'shift by register' instructions
net: bpf: arm64: address randomize and write protect JIT code
arm64: mm: Correct fixmap pagetable types
arm64: compat: fix compat types affecting struct compat_elf_prpsinfo
arm64: Align less than PAGE_SIZE pgds naturally
arm64: Allow 48-bits VA space without ARM_SMMU
Pull two sparc fixes from David Miller:
1) Fix boots with gcc-4.9 compiled sparc64 kernels.
2) Add missing __get_user_pages_fast() on sparc64 to fix hangs on
futexes used in transparent hugepage areas.
It's really idiotic to have a weak symbolled fallback that just
returns zero, and causes this kind of bug. There should be no
backup implementation and the link should fail if the architecture
fails to provide __get_user_pages_fast() and supports transparent
hugepages.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Implement __get_user_pages_fast().
sparc64: Fix register corruption in top-most kernel stack frame during boot.
as what I usually had for the _whole_ rc period.
There are a few bad bugs where the guest can OOPS or crash the host. We
have also started looking at attack models for nested virtualization;
bugs that usually result in the guest ring 0 crashing itself become
more worrisome if you have nested virtualization, because the nested
guest might bring down the non-nested guest as well. For current
uses of nested virtualization these do not really have a security
impact, but you never know and bugs are bugs nevertheless.
A lot of these bugs are in 3.17 too, resulting in a large number of
stable@ Ccs. I checked that all the patches apply there with no
conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJUSjmSAAoJEL/70l94x66D2cYH/3JKWsTzhXjHGxZcXQQ85CwR
49hp/crCLWJ2YRKzyAOkvwPI0/SgYKM5wJ8kgtKlpLxrPZKYwhGd1S9tKf6EdAib
5gc/SDDAgHmkqL3IrXmkyKzUVeUWvgD/IFi1Sqalko1blpRlaN/JyJV0mjjGCbA+
yH3Qi5tD0X00u00ycuZCB6mrFH0PH87BmKFiz6bSSJ43tsgD9AVD64BZid6c6hwm
iaIfNcIuShavlv1TKG80cSez2qtNXjRLeTN8A10gVZo3hof/wP8aRm+LxF/1JEZX
OsoNCjOhhL29qafcZOg3j/atbiAzWtSGV3vjU+iWh5mnN5oFZHcPgIGucQsuFec=
=9oQY
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"This is a pretty large update. I think it is roughly as big as what I
usually had for the _whole_ rc period.
There are a few bad bugs where the guest can OOPS or crash the host.
We have also started looking at attack models for nested
virtualization; bugs that usually result in the guest ring 0 crashing
itself become more worrisome if you have nested virtualization,
because the nested guest might bring down the non-nested guest as
well. For current uses of nested virtualization these do not really
have a security impact, but you never know and bugs are bugs
nevertheless.
A lot of these bugs are in 3.17 too, resulting in a large number of
stable@ Ccs. I checked that all the patches apply there with no
conflicts"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: vfio: fix unregister kvm_device_ops of vfio
KVM: x86: Wrong assertion on paging_tmpl.h
kvm: fix excessive pages un-pinning in kvm_iommu_map error path.
KVM: x86: PREFETCH and HINT_NOP should have SrcMem flag
KVM: x86: Emulator does not decode clflush well
KVM: emulate: avoid accessing NULL ctxt->memopp
KVM: x86: Decoding guest instructions which cross page boundary may fail
kvm: x86: don't kill guest on unknown exit reason
kvm: vmx: handle invvpid vm exit gracefully
KVM: x86: Handle errors when RIP is set during far jumps
KVM: x86: Emulator fixes for eip canonical checks on near branches
KVM: x86: Fix wrong masking on relative jump/call
KVM: x86: Improve thread safety in pit
KVM: x86: Prevent host from panicking on shared MSR writes.
KVM: x86: Check non-canonical addresses upon WRMSR
- Fix regression in xen_clocksource_read() which caused all Xen guests
to crash early in boot.
- Several fixes for super rare race conditions in the p2m.
- Assorted other minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJUSh3nAAoJEFxbo/MsZsTRw6IH/imL2J++b8cafVvHjmVRt1T/
P7KuFYPh/Tym+LISDBfk7MeOXZWsffvUDP653cGQiIMgmumEgVrU1+vR2Z0qRiRe
95ZDIuQBmyGNBG9MiB0+zB7+STsvLECkPVWYDJCNbGVgrlHL6UHne06edrSpfr30
13PyZeJAojezrt2hzLO43V7bu9acRmLo6WNdh6N2stfJv8QSQYSQO87baRdRB+rO
I1r2jP7TJp9ZRtzSTsYLfpyhCGLcvXY58bci+Tz9x6xWMJ/HH5HvfJjxO17HzbdD
2se6MKFVbOXT7DQK+BvQBDIO52t731DWZs4t7SJg24kDoINL7XiC/qSHC0vHJJM=
=Cs0b
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.18-b-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen bug fixes from David Vrabel:
- Fix regression in xen_clocksource_read() which caused all Xen guests
to crash early in boot.
- Several fixes for super rare race conditions in the p2m.
- Assorted other minor fixes.
* tag 'stable/for-linus-3.18-b-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/pci: Allocate memory for physdev_pci_device_add's optarr
x86/xen: panic on bad Xen-provided memory map
x86/xen: Fix incorrect per_cpu accessor in xen_clocksource_read()
x86/xen: avoid race in p2m handling
x86/xen: delay construction of mfn_list_list
x86/xen: avoid writing to freed memory after race in p2m handling
xen/balloon: Don't continue ballooning when BP_ECANCELED is encountered
With 48-bit VA space, the 64K page configuration uses 3 levels instead
of 2 and PUD_SIZE != PMD_SIZE. Since with 64K pages we only cover
PMD_SIZE with the initial swapper_pg_dir populated in head.S, the
memblock current_limit needs to be set accordingly in map_mem() to avoid
allocating unmapped memory. The memblock current_limit is progressively
increased as more blocks are mapped.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
It is not sufficient to only implement get_user_pages_fast(), you
must also implement the atomic version __get_user_pages_fast()
otherwise you end up using the weak symbol fallback implementation
which simply returns zero.
This is dangerous, because it causes the futex code to loop forever
if transparent hugepages are supported (see get_futex_key()).
Signed-off-by: David S. Miller <davem@davemloft.net>
Meelis Roos reported that kernels built with gcc-4.9 do not boot, we
eventually narrowed this down to only impacting machines using
UltraSPARC-III and derivitive cpus.
The crash happens right when the first user process is spawned:
[ 54.451346] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000004
[ 54.451346]
[ 54.571516] CPU: 1 PID: 1 Comm: init Not tainted 3.16.0-rc2-00211-gd7933ab #96
[ 54.666431] Call Trace:
[ 54.698453] [0000000000762f8c] panic+0xb0/0x224
[ 54.759071] [000000000045cf68] do_exit+0x948/0x960
[ 54.823123] [000000000042cbc0] fault_in_user_windows+0xe0/0x100
[ 54.902036] [0000000000404ad0] __handle_user_windows+0x0/0x10
[ 54.978662] Press Stop-A (L1-A) to return to the boot prom
[ 55.050713] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000004
Further investigation showed that compiling only per_cpu_patch() with
an older compiler fixes the boot.
Detailed analysis showed that the function is not being miscompiled by
gcc-4.9, but it is using a different register allocation ordering.
With the gcc-4.9 compiled function, something during the code patching
causes some of the %i* input registers to get corrupted. Perhaps
we have a TLB miss path into the firmware that is deep enough to
cause a register window spill and subsequent restore when we get
back from the TLB miss trap.
Let's plug this up by doing two things:
1) Stop using the firmware stack for client interface calls into
the firmware. Just use the kernel's stack.
2) As soon as we can, call into a new function "start_early_boot()"
to put a one-register-window buffer between the firmware's
deepest stack frame and the top-most initial kernel one.
Reported-by: Meelis Roos <mroos@linux.ee>
Tested-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
When user asks to turn off ASLR by writing "0" to
/proc/sys/kernel/randomize_va_space there should not be
any randomization to mmap base, stack, VDSO, libs, text and heap
Currently arm64 violates this behavior by randomising text.
Fix this by defining a constant ELF_ET_DYN_BASE. The randomisation of
mm->mmap_base is done by setup_new_exec -> arch_pick_mmap_layout ->
mmap_base -> mmap_rnd.
Signed-off-by: Arun Chandran <achandran@mvista.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Even after the recent fix, the assertion on paging_tmpl.h is triggered.
Apparently, the assertion wants to check that the PAE is always set on
long-mode, but does it in incorrect way. Note that the assertion is not
enabled unless the code is debugged by defining MMU_DEBUG.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The decode phase of the x86 emulator assumes that every instruction with the
ModRM flag, and which can be used with RIP-relative addressing, has either
SrcMem or DstMem. This is not the case for several instructions - prefetch,
hint-nop and clflush.
Adding SrcMem|NoAccess for prefetch and hint-nop and SrcMem for clflush.
This fixes CVE-2014-8480.
Fixes: 41061cdb98
Cc: stable@vger.kernel.org
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently, all group15 instructions are decoded as clflush (e.g., mfence,
xsave). In addition, the clflush instruction requires no prefix (66/f2/f3)
would exist. If prefix exists it may encode a different instruction (e.g.,
clflushopt).
Creating a group for clflush, and different group for each prefix.
This has been the case forever, but the next patch needs the cflush group
in order to fix a bug introduced in 3.17.
Fixes: 41061cdb98
Cc: stable@vger.kernel.org
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A failure to decode the instruction can cause a NULL pointer access.
This is fixed simply by moving the "done" label as close as possible
to the return.
This fixes CVE-2014-8481.
Reported-by: Andy Lutomirski <luto@amacapital.net>
Cc: stable@vger.kernel.org
Fixes: 41061cdb98
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A platform driver for which nothing ever registers the corresponding
platform device.
Also it was driving the same hardware as sead3-i2c-drv.c so redundant
anyway and couldn't co-exist with that driver because each of them was
using a private spinlock to protect access to the same hardware
resources.
This also fixes a randconfig problem:
arch/mips/mti-sead3/sead3-pic32-i2c-drv.c: In function 'i2c_platform_probe':
arch/mips/mti-sead3/sead3-pic32-i2c-drv.c:345:2: error: implicit declaration of
function 'i2c_add_numbered_adapter' [-Werror=implicit-function-declaration]
ret = i2c_add_numbered_adapter(&priv->adap);
^
arch/mips/mti-sead3/sead3-pic32-i2c-drv.c: In function
'i2c_platform_remove':
arch/mips/mti-sead3/sead3-pic32-i2c-drv.c:361:2: error: implicit declaration
of function 'i2c_del_adapter' [-Werror=implicit-function-declaration]
i2c_del_adapter(&priv->adap);
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Once an instruction crosses a page boundary, the size read from the second page
disregards the common case that part of the operand resides on the first page.
As a result, fetch of long insturctions may fail, and thereby cause the
decoding to fail as well.
Cc: stable@vger.kernel.org
Fixes: 5cfc7e0f5e
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM_EXIT_UNKNOWN is a kvm bug, we don't really know whether it was
triggered by a priveledged application. Let's not kill the guest: WARN
and inject #UD instead.
Cc: stable@vger.kernel.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
On systems with invvpid instruction support (corresponding bit in
IA32_VMX_EPT_VPID_CAP MSR is set) guest invocation of invvpid
causes vm exit, which is currently not handled and results in
propagation of unknown exit to userspace.
Fix this by installing an invvpid vm exit handler.
This is CVE-2014-3646.
Cc: stable@vger.kernel.org
Signed-off-by: Petr Matousek <pmatouse@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Far jmp/call/ret may fault while loading a new RIP. Currently KVM does not
handle this case, and may result in failed vm-entry once the assignment is
done. The tricky part of doing so is that loading the new CS affects the
VMCS/VMCB state, so if we fail during loading the new RIP, we are left in
unconsistent state. Therefore, this patch saves on 64-bit the old CS
descriptor and restores it if loading RIP failed.
This fixes CVE-2014-3647.
Cc: stable@vger.kernel.org
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Before changing rip (during jmp, call, ret, etc.) the target should be asserted
to be canonical one, as real CPUs do. During sysret, both target rsp and rip
should be canonical. If any of these values is noncanonical, a #GP exception
should occur. The exception to this rule are syscall and sysenter instructions
in which the assigned rip is checked during the assignment to the relevant
MSRs.
This patch fixes the emulator to behave as real CPUs do for near branches.
Far branches are handled by the next patch.
This fixes CVE-2014-3647.
Cc: stable@vger.kernel.org
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Relative jumps and calls do the masking according to the operand size, and not
according to the address size as the KVM emulator does today.
This patch fixes KVM behavior.
Cc: stable@vger.kernel.org
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There's a race condition in the PIT emulation code in KVM. In
__kvm_migrate_pit_timer the pit_timer object is accessed without
synchronization. If the race condition occurs at the wrong time this
can crash the host kernel.
This fixes CVE-2014-3611.
Cc: stable@vger.kernel.org
Signed-off-by: Andrew Honig <ahonig@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The previous patch blocked invalid writes directly when the MSR
is written. As a precaution, prevent future similar mistakes by
gracefulling handle GPs caused by writes to shared MSRs.
Cc: stable@vger.kernel.org
Signed-off-by: Andrew Honig <ahonig@google.com>
[Remove parts obsoleted by Nadav's patch. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Upon WRMSR, the CPU should inject #GP if a non-canonical value (address) is
written to certain MSRs. The behavior is "almost" identical for AMD and Intel
(ignoring MSRs that are not implemented in either architecture since they would
anyhow #GP). However, IA32_SYSENTER_ESP and IA32_SYSENTER_EIP cause #GP if
non-canonical address is written on Intel but not on AMD (which ignores the top
32-bits).
Accordingly, this patch injects a #GP on the MSRs which behave identically on
Intel and AMD. To eliminate the differences between the architecutres, the
value which is written to IA32_SYSENTER_ESP and IA32_SYSENTER_EIP is turned to
canonical value before writing instead of injecting a #GP.
Some references from Intel and AMD manuals:
According to Intel SDM description of WRMSR instruction #GP is expected on
WRMSR "If the source register contains a non-canonical address and ECX
specifies one of the following MSRs: IA32_DS_AREA, IA32_FS_BASE, IA32_GS_BASE,
IA32_KERNEL_GS_BASE, IA32_LSTAR, IA32_SYSENTER_EIP, IA32_SYSENTER_ESP."
According to AMD manual instruction manual:
LSTAR/CSTAR (SYSCALL): "The WRMSR instruction loads the target RIP into the
LSTAR and CSTAR registers. If an RIP written by WRMSR is not in canonical
form, a general-protection exception (#GP) occurs."
IA32_GS_BASE and IA32_FS_BASE (WRFSBASE/WRGSBASE): "The address written to the
base field must be in canonical form or a #GP fault will occur."
IA32_KERNEL_GS_BASE (SWAPGS): "The address stored in the KernelGSbase MSR must
be in canonical form."
This patch fixes CVE-2014-3610.
Cc: stable@vger.kernel.org
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
These patches fixes an SMP and SDMMC driver hang during boot up on the
SOCFPGA platform.
Patch "arm: socfpga: fix fetching cpu1start_addr for SMP" fixes the SMP
trampoline code in order for CPU1 to correctly fetch it's cpu1start_addr.
Patch "ARM: dts: socfpga: rename gpio nodes" renames that GPIO node in order
to allow a standard way of specifying status="okay" in the board DTS file.
Patch "ARM: dts: socfpga: Fix SD card detect" fixes a SDMMC driver hang
during boot. The reason for the hang was the deferred probe of the SDMMC
driver was waiting for the GPIO resource that would never come.
Patch "ARM: dts: socfpga: Add a 3.3V fixed regulator node" adds a fixed
regulator node for the SDMMC driver to use.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=y6Ws
-----END PGP SIGNATURE-----
Merge tag 'socfpga_fixes_for_3.18' of git://git.rocketboards.org/linux-socfpga-next into fixes
Merge "SOCFPGA fixes for 3.18" from Dinh Nguyen:
These patches fixes an SMP and SDMMC driver hang during boot up on the
SOCFPGA platform.
Patch "arm: socfpga: fix fetching cpu1start_addr for SMP" fixes the SMP
trampoline code in order for CPU1 to correctly fetch it's cpu1start_addr.
Patch "ARM: dts: socfpga: rename gpio nodes" renames that GPIO node in order
to allow a standard way of specifying status="okay" in the board DTS file.
Patch "ARM: dts: socfpga: Fix SD card detect" fixes a SDMMC driver hang
during boot. The reason for the hang was the deferred probe of the SDMMC
driver was waiting for the GPIO resource that would never come.
Patch "ARM: dts: socfpga: Add a 3.3V fixed regulator node" adds a fixed
regulator node for the SDMMC driver to use.
* tag 'socfpga_fixes_for_3.18' of git://git.rocketboards.org/linux-socfpga-next:
ARM: dts: socfpga: Add a 3.3V fixed regulator node
ARM: dts: socfpga: Fix SD card detect
ARM: dts: socfpga: rename gpio nodes
arm: socfpga: fix fetching cpu1start_addr for SMP
Signed-off-by: Olof Johansson <olof@lixom.net>
- one more MAINTAINERS entry for the SSC driver
- a fix for the newly introduced power/reset driver
- a fix on at91sam9263 USB due to PLLB misconfiguration
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJUR2b6AAoJEAf03oE53VmQ5cIIAIsML44VaaFCy3fuE4+uXR9p
g5s80QMmV5dK0y/Yqwu/xIgvIEsyY4B9zWCy08w0EgzSHNbAC7iW7U4n2ia+7C9N
QxlOar+vI4A3gBS+9d0N7nEOf7VfnWQ2qmJmd2W5hOdQ0hjEhJIfMZtQYHBd8fN5
4fn/12HoC2iVYgGL9By/UmYVMCI1H1yeaQiYVw3KZkKPxlo6ERVrTVHL5rRjF65s
m7l0Sf2zlmIN3rp24D7TBdr4b8OwUdfakrEqli7t+5kZh6yvFtZhuZE84Aunvy7m
Orw7aT6ZhLDUc2omvCwz0ZNKvDtyt5I8MwWQ7ETeMGFWaeS6bPPALbwyf6Nnffw=
=gRsw
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into fixes
Merge "at91: fixes for v3.18 #1" from Nicholas Ferre:
First AT91 fixes for 3.18:
- one more MAINTAINERS entry for the SSC driver
- a fix for the newly introduced power/reset driver
- a fix on at91sam9263 USB due to PLLB misconfiguration
* tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91/dt: sam9263: fix PLLB frequencies
power: reset: at91-reset: fix power down register
MAINTAINERS: add atmel ssc driver maintainer entry
Signed-off-by: Olof Johansson <olof@lixom.net>
Allows booting from SD/MMC on RK3288 and other platforms. Added here so I
can enable the board in the boot farm.
Signed-off-by: Olof Johansson <olof@lixom.net>
I missed in 9a2ad529ed that REGULATOR_FIXED_VOLTAGE had also gotten
deselected, so it needs to be added back as an explicit option.
Signed-off-by: Olof Johansson <olof@lixom.net>
Code before the .fixup section needs to have the .insn directive.
This has no side effects on MIPS32/64 but it affects the way microMIPS
loads the address for the return label.
Fixes the following build problem:
mips-linux-gnu-ld: arch/mips/built-in.o: .fixup+0x4a0: Unsupported jump between
ISA modes; consider recompiling with interlinking enabled.
mips-linux-gnu-ld: final link failed: Bad value
Makefile:819: recipe for target 'vmlinux' failed
The fix is similar to 1658f914ff ("MIPS: microMIPS:
Disable LL/SC and fix linker bug.")
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: stable@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8117/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When CONFIG_MIPS_MT_SMP is enabled, the following compilation error
occurs:
arch/mips/pmcs-msp71xx/msp_irq_cic.c:134: error: ‘irq’ undeclared
This code clearly never saw a compiler.
The surrounding code suggests, that 'd->irq' was intended, not
'irq'.
This error was found with vampyr.
Signed-off-by: Stefan Hengelein <stefan.hengelein@fau.de>
Fixes: d7881fbdf8 ("MIPS: msp71xx: Convert to new irq_chip functions")
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8116/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
function, where an architecture can override it by providing a strong
version.
Some header file declarations included the "weak" attribute. That's
error-prone because it causes every implementation to be weak, with no
strong version at all, and the linker chooses one based on link order.
What we want is the "weak" attribute only on the *definition* of the
default implementation. These changes remove "weak" from the declarations,
leaving it on the default definitions.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=P4fi
-----END PGP SIGNATURE-----
Merge tag 'remove-weak-declarations' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull weak function declaration removal from Bjorn Helgaas:
"The "weak" attribute is commonly used for the default version of a
function, where an architecture can override it by providing a strong
version.
Some header file declarations included the "weak" attribute. That's
error-prone because it causes every implementation to be weak, with no
strong version at all, and the linker chooses one based on link order.
What we want is the "weak" attribute only on the *definition* of the
default implementation. These changes remove "weak" from the
declarations, leaving it on the default definitions"
* tag 'remove-weak-declarations' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
uprobes: Remove "weak" from function declarations
memory-hotplug: Remove "weak" from memory_block_size_bytes() declaration
kgdb: Remove "weak" from kgdb_arch_pc() declaration
ARC: kgdb: generic kgdb_arch_pc() suffices
vmcore: Remove "weak" from function declarations
clocksource: Remove "weak" from clocksource_default_clock() declaration
x86, intel-mid: Remove "weak" from function declarations
audit: Remove "weak" from audit_classify_compat_syscall() declaration
Pull x86 EFI updates from Peter Anvin:
"This patchset falls under the "maintainers that grovel" clause in the
v3.18-rc1 announcement. We had intended to push it late in the merge
window since we got it into the -tip tree relatively late.
Many of these are relatively simple things, but there are a couple of
key bits, especially Ard's and Matt's patches"
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
rtc: Disable EFI rtc for x86
efi: rtc-efi: Export platform:rtc-efi as module alias
efi: Delete the in_nmi() conditional runtime locking
efi: Provide a non-blocking SetVariable() operation
x86/efi: Adding efi_printks on memory allocationa and pci.reads
x86/efi: Mark initialization code as such
x86/efi: Update comment regarding required phys mapped EFI services
x86/efi: Unexport add_efi_memmap variable
x86/efi: Remove unused efi_call* macros
efi: Resolve some shadow warnings
arm64: efi: Format EFI memory type & attrs with efi_md_typeattr_format()
ia64: efi: Format EFI memory type & attrs with efi_md_typeattr_format()
x86: efi: Format EFI memory type & attrs with efi_md_typeattr_format()
efi: Introduce efi_md_typeattr_format()
efi: Add macro for EFI_MEMORY_UCE memory attribute
x86/efi: Clear EFI_RUNTIME_SERVICES if failing to enter virtual mode
arm64/efi: Do not enter virtual mode if booting with efi=noruntime or noefi
arm64/efi: uefi_init error handling fix
efi: Add kernel param efi=noruntime
lib: Add a generic cmdline parse function parse_option_str
...
The malta-amon.c file provides functions to access the YAMON Monitoring
interface to bring up secondary VPEs in case of SMP/CMP. As a
result of which, there is no need to build it if CMP is not used.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/7993/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The no-op cases of cop2_save & cop2_restore lead to the following
warnings being emitted during build with recent versions of gcc (tested
using gcc 4.8.3 from the Mentor Sourcery CodeBench 2014.05 toolchain):
In file included from ./arch/mips/include/asm/switch_to.h:18:0,
from kernel/sched/core.c:78:
kernel/sched/core.c: In function 'finish_task_switch':
include/asm-generic/current.h:6:45: warning: value computed is not used [-Wunused-value]
#define get_current() (current_thread_info()->task)
^
./arch/mips/include/asm/cop2.h:48:32: note: in definition of macro 'cop2_restore'
#define cop2_restore(r) do { (r); } while (0)
^
include/asm-generic/current.h:7:17: note: in expansion of macro 'get_current'
#define current get_current()
^
./arch/mips/include/asm/switch_to.h:114:16: note: in expansion of macro 'current'
cop2_restore(current); \
^
kernel/sched/core.c:2225:2: note: in expansion of macro 'finish_arch_switch'
finish_arch_switch(prev);
^
Avoid the warning by "using" the value by casting to void.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7880/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The MIPS_CPS_PM and MIPS_CPS_CPUIDLE implementation should depend
on the MIPS_CPS symbol to avoid the following build problem
arch/mips/kernel/pm-cps.c: In function 'cps_pm_enter_state':
arch/mips/kernel/pm-cps.c:164:26: error: 'cpu_coherent_mask' undeclared
(first use in this function)
cpumask_clear_cpu(cpu, &cpu_coherent_mask);
^
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/7798/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The __pastwait symbol was only used by the address_is_in_r4k_wait_irqoff
function but this is no longer used since the SMTC removal in commit
b633648c5a ('MIPS: MT: Remove SMTC support'). That symbol also led to
build failures under certain random configuration due to the way the
compiler compiled the r4k_wait_irqoff function. If that function was
called multiple times, the __pastwait symbol was redefined breaking the
build like this:
CHK include/generated/compile.h
CC arch/mips/kernel/idle.o
{standard input}: Assembler messages:
{standard input}:527: Error: symbol `__pastwait' is already defined
Link: http://www.linux-mips.org/cgi-bin/mesg.cgi?a=linux-mips&i=1244879922.24479.30.camel%40falcon
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/7791/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Panic if Xen provides a memory map with 0 entries. Although this is
unlikely, it is better to catch the error at the point of seeing the map
than later on as a symptom of some other crash.
Signed-off-by: Martin Kelly <martkell@amazon.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Commit 89cbc76768 ("x86: Replace __get_cpu_var uses") replaced
__get_cpu_var() with this_cpu_ptr() in xen_clocksource_read() in such a
way that instead of accessing a structure pointed to by a per-cpu pointer
we are trying to get to a per-cpu structure.
__this_cpu_read() of the pointer is the more appropriate accessor.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
When a new p2m leaf is allocated this leaf is linked into the p2m tree
via cmpxchg. Unfortunately the compare value for checking the success
of the update is read after checking for the need of a new leaf. It is
possible that a new leaf has been linked into the tree concurrently
in between. This could lead to a leaked memory page and to the loss of
some p2m entries.
Avoid the race by using the read compare value for checking the need
of a new p2m leaf and use ACCESS_ONCE() to get it.
There are other places which seem to need ACCESS_ONCE() to ensure
proper operation. Change them accordingly.
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
The 3 level p2m tree for the Xen tools is constructed very early at
boot by calling xen_build_mfn_list_list(). Memory needed for this tree
is allocated via extend_brk().
As this tree (other than the kernel internal p2m tree) is only needed
for domain save/restore, live migration and crash dump analysis it
doesn't matter whether it is constructed very early or just some
milliseconds later when memory allocation is possible by other means.
This patch moves the call of xen_build_mfn_list_list() just after
calling xen_pagetable_p2m_copy() simplifying this function, too, as it
doesn't have to bother with two parallel trees now. The same applies
for some other internal functions.
While simplifying code, make early_can_reuse_p2m_middle() static and
drop the unused second parameter. p2m_mid_identity_mfn can be removed
as well, it isn't used either.
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
In case a race was detected during allocation of a new p2m tree
element in alloc_p2m() the new allocated mid_mfn page is freed without
updating the pointer to the found value in the tree. This will result
in overwriting the just freed page with the mfn of the p2m leaf.
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Fixes the following randconfig build problem:
arch/mips/built-in.o: In function `show_cpuinfo':
proc.c:(.text+0xde84): undefined reference to `get_system_type'
arch/mips/built-in.o: In function `sb1250_setup':
(.init.text+0x428): undefined reference to `get_system_type'
arch/mips/built-in.o: In function `setup_arch':
(.init.text+0x178c): undefined reference to `plat_mem_setup'
Makefile:930: recipe for target 'vmlinux' failed
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8106/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit a79ebea620 (MIPS: ptrace: Fix user pt_regs definition,
use in ptrace_{get, set}regs()) converted struct pt_regs to use __u64.
Some userspace applications (e.g. GDB) include this file directly,
and fail to see this type. Fix by including <linux/types.h>.
The patch fixes the following build failure with GDB 7.8 when using
GLIBC headers created against Linux 3.17:
In file included from /home/aaro/los/work/shared/gdb-7.8/gdb/mips-linux-nat.c:37:0:
/home/aaro/los/work/mips/rootfs/mips-linux-gnu/usr/include/asm/ptrace.h:32:2: error: unknown type name '__u64'
__u64 regs[32];
^
/home/aaro/los/work/mips/rootfs/mips-linux-gnu/usr/include/asm/ptrace.h:35:2: error: unknown type name '__u64'
__u64 lo;
^
/home/aaro/los/work/mips/rootfs/mips-linux-gnu/usr/include/asm/ptrace.h:36:2: error: unknown type name '__u64'
__u64 hi;
^
Fixes: a79ebea620 ("MIPS: ptrace: Fix user pt_regs definition, use in ptrace_{get, set}regs()")
Cc: stable@vger.kernel.org # 3.17
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Alex Smith <alex@alex-smith.me.uk>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8067/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Without the 3.3V regulator node, the SDMMC driver will give these warnings:
dw_mmc ff704000.dwmmc0: No vmmc regulator found
dw_mmc ff704000.dwmmc0: No vqmmc regulator found
This patch adds the regulator node, and points the SD/MMC to the regulator.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
---
v3: Rename nodes to have schematic-name_regulator and remove "boot-on" and
"always-on"
v2: Move the regulator nodes to their respective board dts file and
correctly rename them to match the schematic
