[ Upstream commit c73275cf68 ]
In multi_transaction_new(), the variable t is not freed or passed out
on the failure of copy_from_user(t->data, buf, size), which could lead
to a memleak.
Fix this bug by adding a put_multi_transaction(t) in the error path.
Fixes: 1dea3b41e8 ("apparmor: speed up transactional queries")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Signed-off-by: John Johansen <john.johansen@canonical.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e095493091 ]
If dsa_tag_8021q_setup() fails, for example due to the inability of the
device to install a VLAN, the tag_8021q context of the switch will leak.
Make sure it is freed on the error path.
Fixes: 328621f613 ("net: dsa: tag_8021q: absorb dsa_8021q_setup into dsa_tag_8021q_{,un}register")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20221209235242.480344-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c87b545a2 ]
Whenever trying to load XDP prog on downed interface, function i40e_xdp
was passing vsi->rx_buf_len field to i40e_xdp_setup() which was equal 0.
i40e_open() calls i40e_vsi_configure_rx() which configures that field,
but that only happens when interface is up. When it is down, i40e_open()
is not being called, thus vsi->rx_buf_len is not set.
Solution for this is calculate buffer length in newly created
function - i40e_calculate_vsi_rx_buf_len() that return actual buffer
length. Buffer length is being calculated based on the same rules
applied previously in i40e_vsi_configure_rx() function.
Fixes: 613142b0bb ("i40e: Log error for oversized MTU on device")
Fixes: 0c8493d90b ("i40e: add XDP support for pass and drop actions")
Signed-off-by: Bartosz Staszewski <bartoszx.staszewski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Shwetha Nagaraju <Shwetha.nagaraju@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Saeed Mahameed <saeed@kernel.com>
Link: https://lore.kernel.org/r/20221209185411.2519898-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ede5a38985 ]
When the MAC is connected to a 10 Mb/s PHY and the PTP clock is derived
from the MAC reference clock (default), the clk_ptp_rate becomes too
small and the calculated sub second increment becomes 0 when computed by
the stmmac_config_sub_second_increment() function within
stmmac_init_tstamp_counter().
Therefore, the subsequent div_u64 in stmmac_init_tstamp_counter()
operation triggers a divide by 0 exception as shown below.
[ 95.062067] socfpga-dwmac ff700000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 95.076440] socfpga-dwmac ff700000.ethernet eth0: PHY [stmmac-0:08] driver [NCN26000] (irq=49)
[ 95.095964] dwmac1000: Master AXI performs any burst length
[ 95.101588] socfpga-dwmac ff700000.ethernet eth0: No Safety Features support found
[ 95.109428] Division by zero in kernel.
[ 95.113447] CPU: 0 PID: 239 Comm: ifconfig Not tainted 6.1.0-rc7-centurion3-1.0.3.0-01574-gb624218205b7-dirty #77
[ 95.123686] Hardware name: Altera SOCFPGA
[ 95.127695] unwind_backtrace from show_stack+0x10/0x14
[ 95.132938] show_stack from dump_stack_lvl+0x40/0x4c
[ 95.137992] dump_stack_lvl from Ldiv0+0x8/0x10
[ 95.142527] Ldiv0 from __aeabi_uidivmod+0x8/0x18
[ 95.147232] __aeabi_uidivmod from div_u64_rem+0x1c/0x40
[ 95.152552] div_u64_rem from stmmac_init_tstamp_counter+0xd0/0x164
[ 95.158826] stmmac_init_tstamp_counter from stmmac_hw_setup+0x430/0xf00
[ 95.165533] stmmac_hw_setup from __stmmac_open+0x214/0x2d4
[ 95.171117] __stmmac_open from stmmac_open+0x30/0x44
[ 95.176182] stmmac_open from __dev_open+0x11c/0x134
[ 95.181172] __dev_open from __dev_change_flags+0x168/0x17c
[ 95.186750] __dev_change_flags from dev_change_flags+0x14/0x50
[ 95.192662] dev_change_flags from devinet_ioctl+0x2b4/0x604
[ 95.198321] devinet_ioctl from inet_ioctl+0x1ec/0x214
[ 95.203462] inet_ioctl from sock_ioctl+0x14c/0x3c4
[ 95.208354] sock_ioctl from vfs_ioctl+0x20/0x38
[ 95.212984] vfs_ioctl from sys_ioctl+0x250/0x844
[ 95.217691] sys_ioctl from ret_fast_syscall+0x0/0x4c
[ 95.222743] Exception stack(0xd0ee1fa8 to 0xd0ee1ff0)
[ 95.227790] 1fa0: 00574c4f be9aeca4 00000003 00008914 be9aeca4 be9aec50
[ 95.235945] 1fc0: 00574c4f be9aeca4 0059f078 00000036 be9aee8c be9aef7a 00000015 00000000
[ 95.244096] 1fe0: 005a01f0 be9aec38 004d7484 b6e67d74
Signed-off-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
Fixes: 91a2559c1d ("net: stmmac: Fix sub-second increment")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/de4c64ccac9084952c56a06a8171d738604c4770.1670678513.git.piergiorgio.beruto@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ba18967d4 ]
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave().
Fixes: 81be03e026 ("Bluetooth: RFCOMM: Replace use of memcpy_from_msg with bt_skb_sendmmsg")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39c1eb6fcb ]
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave().
Fixes: 9238f36a5a ("Bluetooth: Add request cmd_complete and cmd_status functions")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b503e339c ]
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave().
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 383630cc67 ]
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave().
Fixes: 43eb12d789 ("Bluetooth: Fix/implement Three-wire reliable packet sending")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f458f783d ]
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave().
Fixes: 166d2f6a43 ("[Bluetooth] Add UART driver for Texas Instruments' BRF63xx chips")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df4cfc9120 ]
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave().
Fixes: 0ff252c197 ("Bluetooth: hciuart: Add support QCA chipset for UART")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b15a6bd3c8 ]
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave().
Fixes: 803b58367f ("Bluetooth: btusb: Implement driver internal packet reassembly")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cee50ce899 ]
skb allocated by __hci_cmd_sync would not be used whether in checking
for supported iBT hardware variants or after, we should free it in all
error branches, this patch makes the case read version failed or default
error case free skb before return.
Fixes: c86c7285bb ("Bluetooth: btintel: Fix the legacy bootloader returns tlv based version")
Fixes: 019a1caa7f ("Bluetooth: btintel: Refactoring setup routine for bootloader devices")
Signed-off-by: Wang ShaoBo <bobo.shaobowang@huawei.com>
Reviewed-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b1c7c00b8 ]
When validating the parameter length for MGMT_OP_ADD_EXT_ADV_PARAMS
command, use the correct op code in error status report:
was MGMT_OP_ADD_ADVERTISING, changed to MGMT_OP_ADD_EXT_ADV_PARAMS.
Fixes: 1241057283 ("Bluetooth: Break add adv into two mgmt commands")
Signed-off-by: Inga Stotland <inga.stotland@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da05cecc49 ]
Recently, a customer reported that from their container whose
net namespace is different to the host's init_net, they can't set
the container's net.sctp.rto_max to any value smaller than
init_net.sctp.rto_min.
For instance,
Host:
sudo sysctl net.sctp.rto_min
net.sctp.rto_min = 1000
Container:
echo 100 > /mnt/proc-net/sctp/rto_min
echo 400 > /mnt/proc-net/sctp/rto_max
echo: write error: Invalid argument
This is caused by the check made from this'commit 4f3fdf3bc5
("sctp: add check rto_min and rto_max in sysctl")'
When validating the input value, it's always referring the boundary
value set for the init_net namespace.
Having container's rto_max smaller than host's init_net.sctp.rto_min
does make sense. Consider that the rto between two containers on the
same host is very likely smaller than it for two hosts.
So to fix this problem, as suggested by Marcelo, this patch makes the
extra pointers of rto_min, rto_max, pf_retrans, and ps_retrans point
to the corresponding variables from the newly created net namespace while
the new net namespace is being registered in sctp_sysctl_net_register.
Fixes: 4f3fdf3bc5 ("sctp: add check rto_min and rto_max in sysctl")
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Firo Yang <firo.yang@suse.com>
Link: https://lore.kernel.org/r/20221209054854.23889-1-firo.yang@suse.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f7d78b2b1 ]
TX/RX callback handlers (ntb_netdev_tx_handler(),
ntb_netdev_rx_handler()) can be called in interrupt
context via the DMA framework when the respective
DMA operations have completed. As such, any calls
by these routines to free skb's, should use the
interrupt context safe dev_kfree_skb_any() function.
Previously, these callback handlers would call the
interrupt unsafe version of dev_kfree_skb(). This has
not presented an issue on Intel IOAT DMA engines as
that driver utilizes tasklets rather than a hard
interrupt handler, like the AMD PTDMA DMA driver.
On AMD systems, a kernel WARNING message is
encountered, which is being issued from
skb_release_head_state() due to in_hardirq()
being true.
Besides the user visible WARNING from the kernel,
the other symptom of this bug was that TCP/IP performance
across the ntb_netdev interface was very poor, i.e.
approximately an order of magnitude below what was
expected. With the repair to use dev_kfree_skb_any(),
kernel WARNINGs from skb_release_head_state() ceased
and TCP/IP performance, as measured by iperf, was on
par with expected results, approximately 20 Gb/s on
AMD Milan based server. Note that this performance
is comparable with Intel based servers.
Fixes: 765ccc7bc3 ("ntb_netdev: correct skb leak")
Fixes: 548c237c0a ("net: Add support for NTB virtual ethernet device")
Signed-off-by: Eric Pilmore <epilmore@gigaio.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20221209000659.8318-1-epilmore@gigaio.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8964916d20 ]
This patch fixes an issue where a read failure of a port statistic counter
will return unknown results. While it is highly unlikely the read will
ever fail, it is much cleaner to return a zero for the stat count.
Fixes: a1292595e0 ("net: dsa: add new DSA switch driver for the SMSC-LAN9303")
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221209153502.7429-1-jerry.ray@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 67727a17a6 ]
TCAN4X5X_ERROR_STATUS is not a status register that needs clearing
during interrupt handling. Instead this is a masking register that masks
error interrupts. Writing TCAN4X5X_CLEAR_ALL_INT to this register
effectively masks everything.
Rename the register and mask all error interrupts only once by writing
to the register in tcan4x5x_init.
Fixes: 5443c226ba ("can: tcan4x5x: Add tcan4x5x driver to the kernel")
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20221206115728.1056014-10-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eaacfeaca7 ]
When we try to access the mcan message ram addresses during the probe,
hclk is gated by any other drivers or disabled, because of that probe
gets failed.
Move the mram init functionality to mcan chip config called by
m_can_start from mcan open function, by that time clocks are
enabled.
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Vivek Yadav <vivek.2311@samsung.com>
Link: https://lore.kernel.org/all/20221207100632.96200-2-vivek.2311@samsung.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Stable-dep-of: 67727a17a6 ("can: tcan4x5x: Fix use of register error status mask")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 40c9e4f676 ]
Register 0x824 TCAN4X5X_MCAN_INT_REG is a read-only register. Any writes
to this register do not have any effect.
Remove this write. The m_can driver aldready clears the interrupts in
m_can_isr() by writing to M_CAN_IR which is translated to register
0x1050 which is a writable version of this register.
Fixes: 5443c226ba ("can: tcan4x5x: Add tcan4x5x driver to the kernel")
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20221206115728.1056014-9-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f8ab263d4d ]
There are cables that exist that can support speeds in excess of 10GbE.
The driver, however, restricts the EEPROM advertised nominal bitrate to
a specific range, which can prevent usage of cables that can support,
for example, up to 25GbE.
Rather than checking that an active or passive cable supports a specific
range, only check for a minimum supported speed.
Fixes: abf0a1c2b2 ("amd-xgbe: Add support for SFP+ modules")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4998006c73 ]
SFP+ active and passive cables are copper cables with fixed SFP+ end
connectors. Due to a misinterpretation of this, SFP+ active cables could
end up not being recognized, causing the driver to fail to establish a
connection.
Introduce a new enum in SFP+ cable types, XGBE_SFP_CABLE_FIBER, that is
the default cable type, and handle active and passive cables when they are
specifically detected.
Fixes: abf0a1c2b2 ("amd-xgbe: Add support for SFP+ modules")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6151d105df ]
It is not allowed to call kfree_skb() or consume_skb() from hardware
interrupt context or with hardware interrupts being disabled.
It should use dev_kfree_skb_irq() or dev_consume_skb_irq() instead.
The difference between them is free reason, dev_kfree_skb_irq() means
the SKB is dropped in error and dev_consume_skb_irq() means the SKB
is consumed in normal.
In these two cases, dev_kfree_skb() is called consume the xmited SKB,
so replace it with dev_consume_skb_irq().
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3727f74291 ]
It is not allowed to call kfree_skb() or consume_skb() from hardware
interrupt context or with hardware interrupts being disabled.
It should use dev_kfree_skb_irq() or dev_consume_skb_irq() instead.
The difference between them is free reason, dev_kfree_skb_irq() means
the SKB is dropped in error and dev_consume_skb_irq() means the SKB
is consumed in normal.
In scc_discard_buffers(), dev_kfree_skb() is called to discard the SKBs,
so replace it with dev_kfree_skb_irq().
In scc_net_tx(), dev_kfree_skb() is called to drop the SKB that exceed
queue length, so replace it with dev_kfree_skb_irq().
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f07fadcbee ]
It is not allowed to call kfree_skb() or consume_skb() from hardware
interrupt context or with hardware interrupts being disabled.
In this case, the lock is used to protected 'bp', so we can move
dev_kfree_skb() after the spin_unlock_irqrestore().
Fixes: 4796417417 ("dnet: Dave DNET ethernet controller driver (updated)")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d1678bf45f ]
It is not allowed to call kfree_skb() or consume_skb() from hardware
interrupt context or with hardware interrupts being disabled.
It should use dev_kfree_skb_irq() or dev_consume_skb_irq() instead.
The difference between them is free reason, dev_kfree_skb_irq() means
the SKB is dropped in error and dev_consume_skb_irq() means the SKB
is consumed in normal.
In this case, dev_kfree_skb() is called in xemaclite_tx_timeout() to
drop the SKB, when tx timeout, so replace it with dev_kfree_skb_irq().
Fixes: bb81b2ddfa ("net: add Xilinx emac lite device driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5fe02e046e ]
It is not allowed to call kfree_skb() or consume_skb() from hardware
interrupt context or with hardware interrupts being disabled.
It should use dev_kfree_skb_irq() or dev_consume_skb_irq() instead.
The difference between them is free reason, dev_kfree_skb_irq() means
the SKB is dropped in error and dev_consume_skb_irq() means the SKB
is consumed in normal.
In this case, dev_kfree_skb() is called in bmac_tx_timeout() to drop
the SKB, when tx timeout, so replace it with dev_kfree_skb_irq().
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3dfe3486c1 ]
It is not allowed to call kfree_skb() or consume_skb() from hardware
interrupt context or with hardware interrupts being disabled.
It should use dev_kfree_skb_irq() or dev_consume_skb_irq() instead.
The difference between them is free reason, dev_kfree_skb_irq() means
the SKB is dropped in error and dev_consume_skb_irq() means the SKB
is consumed in normal.
In this case, dev_kfree_skb() is called in mace_tx_timeout() to drop
the SKB, when tx timeout, so replace it with dev_kfree_skb_irq().
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3cf7203ca6 ]
There is a race condition in vxlan that when deleting a vxlan device
during receiving packets, there is a possibility that the sock is
released after getting vxlan_sock vs from sk_user_data. Then in
later vxlan_ecn_decapsulate(), vxlan_get_sk_family() we will got
NULL pointer dereference. e.g.
#0 [ffffa25ec6978a38] machine_kexec at ffffffff8c669757
#1 [ffffa25ec6978a90] __crash_kexec at ffffffff8c7c0a4d
#2 [ffffa25ec6978b58] crash_kexec at ffffffff8c7c1c48
#3 [ffffa25ec6978b60] oops_end at ffffffff8c627f2b
#4 [ffffa25ec6978b80] page_fault_oops at ffffffff8c678fcb
#5 [ffffa25ec6978bd8] exc_page_fault at ffffffff8d109542
#6 [ffffa25ec6978c00] asm_exc_page_fault at ffffffff8d200b62
[exception RIP: vxlan_ecn_decapsulate+0x3b]
RIP: ffffffffc1014e7b RSP: ffffa25ec6978cb0 RFLAGS: 00010246
RAX: 0000000000000008 RBX: ffff8aa000888000 RCX: 0000000000000000
RDX: 000000000000000e RSI: ffff8a9fc7ab803e RDI: ffff8a9fd1168700
RBP: ffff8a9fc7ab803e R8: 0000000000700000 R9: 00000000000010ae
R10: ffff8a9fcb748980 R11: 0000000000000000 R12: ffff8a9fd1168700
R13: ffff8aa000888000 R14: 00000000002a0000 R15: 00000000000010ae
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
#7 [ffffa25ec6978ce8] vxlan_rcv at ffffffffc10189cd [vxlan]
#8 [ffffa25ec6978d90] udp_queue_rcv_one_skb at ffffffff8cfb6507
#9 [ffffa25ec6978dc0] udp_unicast_rcv_skb at ffffffff8cfb6e45
#10 [ffffa25ec6978dc8] __udp4_lib_rcv at ffffffff8cfb8807
#11 [ffffa25ec6978e20] ip_protocol_deliver_rcu at ffffffff8cf76951
#12 [ffffa25ec6978e48] ip_local_deliver at ffffffff8cf76bde
#13 [ffffa25ec6978ea0] __netif_receive_skb_one_core at ffffffff8cecde9b
#14 [ffffa25ec6978ec8] process_backlog at ffffffff8cece139
#15 [ffffa25ec6978f00] __napi_poll at ffffffff8ceced1a
#16 [ffffa25ec6978f28] net_rx_action at ffffffff8cecf1f3
#17 [ffffa25ec6978fa0] __softirqentry_text_start at ffffffff8d4000ca
#18 [ffffa25ec6978ff0] do_softirq at ffffffff8c6fbdc3
Reproducer: https://github.com/Mellanox/ovs-tests/blob/master/test-ovs-vxlan-remove-tunnel-during-traffic.sh
Fix this by waiting for all sk_user_data reader to finish before
releasing the sock.
Reported-by: Jianlin Shi <jishi@redhat.com>
Suggested-by: Jakub Sitnicki <jakub@cloudflare.com>
Fixes: 6a93cc9052 ("udp-tunnel: Add a few more UDP tunnel APIs")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6cee96e09d ]
It is not allowed to call kfree_skb() or consume_skb() from hardware
interrupt context or with hardware interrupts being disabled.
It should use dev_kfree_skb_irq() or dev_consume_skb_irq() instead.
The difference between them is free reason, dev_kfree_skb_irq() means
the SKB is dropped in error and dev_consume_skb_irq() means the SKB
is consumed in normal.
In this case, dev_kfree_skb() is called in free_tx_buffers() to drop
the SKBs in tx buffers, when the card is down, so replace it with
dev_kfree_skb_irq() here.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee9d7a0e75 ]
When kmalloc() fail to allocate memory in kasprintf(), fn_1 or fn_2 will
be NULL, and strcmp() will cause null pointer dereference.
Fixes: 2fe0e8769d ("of: overlay: check prevents multiple fragments touching same property")
Signed-off-by: ruanjinjie <ruanjinjie@huawei.com>
Link: https://lore.kernel.org/r/20221211023337.592266-1-ruanjinjie@huawei.com
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 01de112332 ]
If vp alloc failed in qlcnic_sriov_init(), all previously allocated vp
needs to be freed.
Fixes: f197a7aa62 ("qlcnic: VF-PF communication channel implementation")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a137f3f27f ]
The bitmap_free() should be called to free priv->af_xdp_zc_qps
when create_singlethread_workqueue() fails, otherwise there will
be a memory leak, so we add the err path error_wq_init to fix it.
Fixes: bba2556efa ("net: stmmac: Enable RX via AF_XDP zero-copy")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f150b63f3f ]
The skb allocated by stmmac_test_get_arp_skb() hasn't been released in
some error handling case, which will lead to a memory leak. Fix this up
by adding kfree_skb() to release skb.
Compile tested only.
Fixes: 5e3fb0a6e2 ("net: stmmac: selftests: Implement the ARP Offload test")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ae18dcdff0 ]
When eisa_driver_register() or tc_register_driver() failed,
the modprobe defxx would fail with some err log as follows:
Error: Driver 'defxx' is already registered, aborting...
Fix this issue by adding err hanling in dfx_init().
Fixes: e89a2cfb7d ("[TC] defxx: TURBOchannel support")
Signed-off-by: Yongqiang Liu <liuyongqiang13@huawei.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44aa5a6dba ]
vmci_transport_dgram_enqueue() does not check the return value
of memcpy_from_msg(). If memcpy_from_msg() fails, it is possible that
uninitialized memory contents are sent unintentionally instead of user's
message in the datagram to the destination. Return with an error if
memcpy_from_msg() fails.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 0f7db23a07 ("vmci_transport: switch ->enqeue_dgram, ->enqueue_stream and ->dequeue_stream to msghdr")
Signed-off-by: Artem Chernyshev <artem.chernyshev@red-soft.ru>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Vishnu Dasa <vdasa@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d35af0a7fe ]
In BPF all global functions, and BPF helpers return a 64-bit
value. For kfunc calls, this is not the case, and they can return
e.g. 32-bit values.
The return register R0 for kfuncs calls can therefore be marked as
subreg_def != DEF_NOT_SUBREG. In general, if a register is marked with
subreg_def != DEF_NOT_SUBREG, some archs (where bpf_jit_needs_zext()
returns true) require the verifier to insert explicit zero-extension
instructions.
For kfuncs calls, however, the caller should do sign/zero extension
for return values. In other words, the compiler is responsible to
insert proper instructions, not the verifier.
An example, provided by Yonghong Song:
$ cat t.c
extern unsigned foo(void);
unsigned bar1(void) {
return foo();
}
unsigned bar2(void) {
if (foo()) return 10; else return 20;
}
$ clang -target bpf -mcpu=v3 -O2 -c t.c && llvm-objdump -d t.o
t.o: file format elf64-bpf
Disassembly of section .text:
0000000000000000 <bar1>:
0: 85 10 00 00 ff ff ff ff call -0x1
1: 95 00 00 00 00 00 00 00 exit
0000000000000010 <bar2>:
2: 85 10 00 00 ff ff ff ff call -0x1
3: bc 01 00 00 00 00 00 00 w1 = w0
4: b4 00 00 00 14 00 00 00 w0 = 0x14
5: 16 01 01 00 00 00 00 00 if w1 == 0x0 goto +0x1 <LBB1_2>
6: b4 00 00 00 0a 00 00 00 w0 = 0xa
0000000000000038 <LBB1_2>:
7: 95 00 00 00 00 00 00 00 exit
If the return value of 'foo()' is used in the BPF program, the proper
zero-extension will be done.
Currently, the verifier correctly marks, say, a 32-bit return value as
subreg_def != DEF_NOT_SUBREG, but will fail performing the actual
zero-extension, due to a verifier bug in
opt_subreg_zext_lo32_rnd_hi32(). load_reg is not properly set to R0,
and the following path will be taken:
if (WARN_ON(load_reg == -1)) {
verbose(env, "verifier bug. zext_dst is set, but no reg is defined\n");
return -EFAULT;
}
A longer discussion from v1 can be found in the link below.
Correct the verifier by avoiding doing explicit zero-extension of R0
for kfunc calls. Note that R0 will still be marked as a sub-register
for return values smaller than 64-bit.
Fixes: 83a2881903 ("bpf: Account for BPF_FETCH in insn_has_def32()")
Link: https://lore.kernel.org/bpf/20221202103620.1915679-1-bjorn@kernel.org/
Suggested-by: Yonghong Song <yhs@meta.com>
Signed-off-by: Björn Töpel <bjorn@rivosinc.com>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/r/20221207103540.396496-1-bjorn@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f596da3efa ]
When the blk_classic option is enabled, non-blktrace events must be
filtered out. Otherwise, events of other types are output in the blktrace
classic format, which is unexpected.
The problem can be triggered in the following ways:
# echo 1 > /sys/kernel/debug/tracing/options/blk_classic
# echo 1 > /sys/kernel/debug/tracing/events/enable
# echo blk > /sys/kernel/debug/tracing/current_tracer
# cat /sys/kernel/debug/tracing/trace_pipe
Fixes: c71a896154 ("blktrace: add ftrace plugin")
Signed-off-by: Yang Jihong <yangjihong1@huawei.com>
Link: https://lore.kernel.org/r/20221122040410.85113-1-yangjihong1@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2f2924bc7 ]
Fix to return a negative error code instead of 0 when
brcmf_chip_set_active() fails. In addition, change the return
value for brcmf_pcie_exit_download_state() to keep consistent.
Fixes: d380ebc9b6 ("brcmfmac: rename chip download functions")
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/1669959342-27144-1-git-send-email-wangyufen@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 76c16af2cb ]
The gen 2 chips RTL8192EU and RTL8188FU periodically send the driver
reports about the TX rate, and the driver passes these reports to
sta_statistics. The reports from RTL8192EU may or may not include the
channel width. The reports from RTL8188FU do not include it.
Only access the c2h->ra_report.bw field if the report (skb) is big
enough.
The other problem fixed here is that the code was actually never
changing the channel width initially reported by
rtl8xxxu_bss_info_changed because the value of RATE_INFO_BW_20 is 0.
Fixes: 0985d3a410 ("rtl8xxxu: Feed current txrate information for mac80211")
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/5b41f1ae-72e7-6b7a-2459-b736399a1c40@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd469a754a ]
This struct is used to access a sequence of bytes received from the
wifi chip. It must not have any padding bytes between the members.
This doesn't change anything on my system, possibly because currently
none of the members need more than byte alignment.
Fixes: b2b43b7837 ("rtl8xxxu: Initial functionality to handle C2H events for 8723bu")
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/1a270918-da22-ff5f-29fc-7855f740c5ba@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a6f994f84 ]
The addition of 3WIRE support would affect MOSI direction even
when still in standard (4 wire) mode. This can lead to MOSI being
at an invalid logic level when a device driver sets an SPI
message with a NULL tx_buf.
spi.h states that if tx_buf is NULL then "zeros will be shifted
out ... " If MOSI is tristated then the data shifted out is subject
to pull resistors, keepers, or in the absence of those, noise.
This issue came to light when using spi-gpio connected to an
ADS7843 touchscreen controller. MOSI pulled high when clocking
MISO data in caused the SPI device to interpret this as a command
which would put the device in an unexpected and non-functional
state.
Fixes: 4b859db2c6 ("spi: spi-gpio: add SPI_3WIRE support")
Fixes: 5132b3d283 ("spi: gpio: Support 3WIRE high-impedance turn-around")
Signed-off-by: Kris Bahnsen <kris@embeddedTS.com>
Link: https://lore.kernel.org/r/20221207230853.6174-1-kris@embeddedTS.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5174e5b0d1 ]
If clk_register() fails, @pll->rate_table may have allocated memory by
kmemdup(), so it needs to be freed, otherwise will cause memory leak
issue, this patch fixes it.
Fixes: 3ff6e0d8d6 ("clk: samsung: Add support to register rate_table for samsung plls")
Signed-off-by: Xiu Jianfeng <xiujianfeng@huawei.com>
Link: https://lore.kernel.org/r/20221123032015.63980-1-xiujianfeng@huawei.com
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e5e5defdb ]
As the kmalloc may return NULL pointer,
it should be better to check the return value
in order to avoid NULL poineter dereference,
same as the others.
Fixes: cb1d3a3363 ("[media] coda: add CODA7541 JPEG support")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b8082238f ]
As the coda_iram_alloc may return NULL pointer,
it should be better to check the return value
in order to avoid NULL poineter dereference,
same as the others.
Fixes: b313bcc9a4 ("[media] coda: simplify IRAM setup")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63ff05a1ad ]
In configure_channels(), we should call of_node_put() when breaking
out of for_each_child_of_node() which will automatically increase
and decrease the refcount.
Fixes: c5f5d0f997 ("[media] c8sectpfe: STiH407/10 Linux DVB demux support")
Signed-off-by: Liang He <windhl@126.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf34ac6aa2 ]
The reg_node needs to be released through of_node_put() in the error
handling path when of_irq_get_byname() failed.
Fixes: 390af53e04 ("regulator: qcom-labibb: Implement short-circuit and over-current IRQs")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Link: https://lore.kernel.org/r/20221203062109.115043-1-yuancan@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
