The USB controllers on sc7280 do not retain the state when
the system goes into low power state and the GDSCs are
turned off. This results in the controllers reinitializing and
re-enumerating all the connected devices (resulting in additional
delay while coming out of suspend)
Fix this by updating the .pwrsts for the USB GDSCs so they only
transition to retention state in low power.
Since sc7280 only supports cx (parent of usb gdscs) Retention, there
are no cxcs offsets mentioned in order to support the Retention
state.
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220920111517.10407-3-quic_rjendra@quicinc.com
The USB controller on sc7180 does not retain the state when
the system goes into low power state and the GDSC is
turned off. This results in the controller reinitializing and
re-enumerating all the connected devices (resulting in additional
delay while coming out of suspend)
Fix this by updating the .pwrsts for the USB GDSC so it only
transitions to retention state in low power.
Since sc7180 only supports cx (parent of usb gdsc) Retention, there
are no cxcs offsets mentioned in order to support the Retention
state.
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220920111517.10407-2-quic_rjendra@quicinc.com
GDSCs cannot be transitioned into a Retention state in SW.
When either the RETAIN_MEM bit, or both the RETAIN_MEM and
RETAIN_PERIPH bits are set, and the GDSC is left ON, the HW
takes care of retaining the memory/logic for the domain when
the parent domain transitions to power collapse/power off state.
On some platforms where the parent domains lowest power state
itself is Retention, just leaving the GDSC in ON (without any
RETAIN_MEM/RETAIN_PERIPH bits being set) will also transition
it to Retention.
The existing logic handling the PWRSTS_RET seems to set the
RETAIN_MEM/RETAIN_PERIPH bits if the cxcs offsets are specified
but then explicitly turns the GDSC OFF as part of _gdsc_disable().
Fix that by leaving the GDSC in ON state.
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220920111517.10407-1-quic_rjendra@quicinc.com
The Snapdragon 670 uses the RPMh mailbox for most of the clocks used in
SDM845 but omits two. Add clock data for SDM670 so the driver doesn't fail
to resolve a clock.
Link: 443bd8d6e2%5E%21/#F7
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220920223734.151135-3-mailingradian@gmail.com
The qcom2260 and sm6115 GCC drivers use a common modified DEFAULT and
BRAMMO alpha pll offsets. Move these common offsets to the shared place
to avoid duplication. The new layouts have a suffix EVO similar to LUCID
and RIVIAN.
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220830075620.974009-4-iskren.chernev@gmail.com
The DEFAULT and BRAMMO PLL offsets are non-standard in downstream, but
currently only BRAMMO ones are overridden. Override DEFAULT ones too.
A very similar thing is happening in gcc-qcm2290 driver.
Fixes: cbe63bfdc5 ("clk: qcom: Add Global Clock controller (GCC) driver for SM6115")
Signed-off-by: Adam Skladowski <a_skl39@protonmail.com>
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220830075620.974009-2-iskren.chernev@gmail.com
PLLs can be kept in standby (default configuration) or in off mode
when disabled during power collapse. Hence add support for pll
disable off mode for lucid evo PLL.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220908222850.3552050-3-dmitry.baryshkov@linaro.org
Add support for the display clock controller found in SM6115/SM4250
based devices. This clock controller feeds the Multimedia Display
SubSystem (MDSS).
This driver is based upon one submitted for QCM2290.
Signed-off-by: Adam Skladowski <a39.skl@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220911164635.182973-3-a39.skl@gmail.com
Enabling PCIe GDSC retention to ensure controller and its
dependent clocks won't go down during system suspend.
Update the .pwrsts for PCIe GDSC so it only transitions
to RET in low power.
Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/1663669347-29308-6-git-send-email-quic_krichai@quicinc.com
Change the qcom_cc_probe_by_index() call to qcom_cc_really_probe()
to avoid remapping of memory region for index 0, which is already
being done through qcom_cc_map().
Fixes: 7c6a6641c2 ("clk: qcom: lpass: Add support for resets & external mclk for SC7280")
Signed-off-by: Satya Priya <quic_c_skakit@quicinc.com>
Reviewed-by: Neil Armstrong <neil.armstrong@baylibre.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/1663673683-7018-1-git-send-email-quic_c_skakit@quicinc.com
Add support for IPQ8074 since it uses the same PLL setup, however it uses
slightly different Alpha PLL config.
Alpha PLL config was obtained by dumping PLL registers from a running
device.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220818220628.339366-7-robimarko@gmail.com
Convert the driver to use OF match data for providing the Alpha PLL config
per compatible.
This is required for IPQ8074 support since it uses a different Alpha PLL
config.
While we are here rename "ipq_pll_config" to "ipq6018_pll_config" to make
it clear that it is for IPQ6018 only.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220818220628.339366-5-robimarko@gmail.com
While fixing up the driver I noticed that my IPQ8074 board was hanging
after CPUFreq switched the frequency during boot, WDT would eventually
reset it.
So mark apcs_alias0_core_clk as critical since its the clock feeding the
CPU cluster and must never be disabled.
Fixes: 5e77b4ef1b ("clk: qcom: Add ipq6018 apss clock controller")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220818220628.339366-3-robimarko@gmail.com
While working on IPQ8074 APSS driver it was discovered that IPQ6018 and
IPQ8074 use almost the same PLL and APSS clocks, however APSS driver is
currently broken.
More precisely apcs_alias0_clk_src is broken, it was added as regmap_mux
clock.
However after debugging why it was always stuck at 800Mhz, it was figured
out that its not regmap_mux compatible at all.
It is a simple mux but it uses RCG2 register layout and control bits, so
utilize the new clk_rcg2_mux_closest_ops to correctly drive it while not
having to provide a dummy frequency table.
While we are here, use ARRAY_SIZE for number of parents.
Tested on IPQ6018-CP01-C1 reference board and multiple IPQ8074 boards.
Fixes: 5e77b4ef1b ("clk: qcom: Add ipq6018 apss clock controller")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220818220628.339366-2-robimarko@gmail.com
An RCG may act as a mux that switch between 2 parents.
This is the case on IPQ6018 and IPQ8074 where the APCS core clk that feeds
the CPU cluster clock just switches between XO and the PLL that feeds it.
Add the required ops to add support for this special configuration and use
the generic mux function to determine the rate.
This way we dont have to keep a essentially dummy frequency table to use
RCG2 as a mux.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220818220628.339366-1-robimarko@gmail.com
Use ARRAY_SIZE for num_parents instead of raw number to prevent any
confusion/mistake.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220724182329.9891-4-ansuelsmth@gmail.com
Convert lcc-ipq806x driver to parent_data API.
Change parent_name for pll4 to pxo_board to prepare the future to
eventually drop the double pxo board clk.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220724182329.9891-3-ansuelsmth@gmail.com
Don't store pointers to parents in struct clk_cpu_8996_pmux. Instead use
clk_hw_get_parent_by_index to fetch them.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220714100351.1834711-6-dmitry.baryshkov@linaro.org
Rather than telling everybody that we are using PLL as a parent (and
using ACD clock instead) properly select ACD as a pmux parent clock.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220714100351.1834711-5-dmitry.baryshkov@linaro.org
Switch to using devres-managed version of clk_notifier_register(). This
allows us to drop driver's remove() callback.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220714100351.1834711-3-dmitry.baryshkov@linaro.org
Replace parent_names in PLLs, secondary muxes and primary muxes with
parent_data. For primary muxes there were never any *cl_pll_acd clocks,
so instead of adding them, put the primary PLLs in both PLL_INDEX and
ACD_INDEX, then make sure ACD_INDEX is always picked over PLL_INDEX when
setting parent since we always want ACD when using the primary PLLs.
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
[DB: switch to parent_hws for pmux clocks]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220714100351.1834711-2-dmitry.baryshkov@linaro.org
There is nothing special about the secondary muxes, unlike the
primary muxes which need some extra logic to handle ACD and
switching between primary PLL and secondary mux sources. Turn
them into clk_regmap_mux and rename cpu_clk_msm8996_mux into
cpu_clk_msm8996_pmux to make it specific to primary muxes.
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220621160621.24415-5-y.oudjana@protonmail.com
The power cluster comes before the performance cluster. Make
everything in the driver follow this order.
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220621160621.24415-4-y.oudjana@protonmail.com
This will allow for adding them to clk_parent_data arrays
in an upcoming patch.
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220621160621.24415-3-y.oudjana@protonmail.com
The parent at this index is the secondary mux, which can connect
not only to primary PLL/2 but also to XO. Rename the index to SMUX_INDEX
to better reflect the parent.
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220621160621.24415-2-y.oudjana@protonmail.com
The USB PHY on MSM8909 works with the driver used on MSM8916
(phy-qcom-usb-hs.c). When turning the PHY on/off it is first reset
using the standard reset controller API. On MSM8916 the reset is
provided by the USB driver (ci_hdrc_msm_por_reset() in ci_hdrc_msm.c).
While this seems to work on MSM8909 as well, the Qualcomm Linux sources
suggest that the PHY should be reset using the GCC_USB2_HS_PHY_ONLY_BCR
register instead. In general this is easy to set up in the device tree,
thanks to the standard reset controller API.
However, to conform to the specifications of the PHY the reset signal
should be asserted for at least 10 us. This is handled correctly on
MSM8916 in ci_hdrc_msm_por_reset(), but not within the GCC driver.
Fix this by making use of the new "udelay" field of qcom_reset_map
and set a delay of ~15 us between the assertion/deassertion of the
USB PHY reset signal.
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220706134132.3623415-5-stephan.gerhold@kernkonzept.com
The amount of time required between asserting and deasserting the reset
signal can vary depending on the involved hardware component. Sometimes
1 us might not be enough and a larger delay is necessary to conform to
the specifications.
Usually this is worked around in the consuming drivers, by replacing
reset_control_reset() with a sequence of reset_control_assert(), waiting
for a custom delay, followed by reset_control_deassert().
However, in some cases the driver making use of the reset is generic and
can be used with different reset controllers. In this case the reset
time requirement is better handled directly by the reset controller
driver.
Make this possible by adding an "udelay" field to the qcom_reset_map
that allows setting a different reset delay (in microseconds).
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220706134132.3623415-4-stephan.gerhold@kernkonzept.com
The Global Clock Controller (GCC) in the MSM8909 SoC provides clocks,
resets and power domains for the various hardware blocks in the SoC.
Add a driver for it to make it possible to enable additional
functionality for the SoC.
Work on this driver was originally started independently by Dominik,
I picked it up and added missing clocks/resets, as well as various
cleanup to bring it into shape for mainline.
Co-developed-by: Dominik Kobinski <dominikkobinski314@gmail.com>
Signed-off-by: Dominik Kobinski <dominikkobinski314@gmail.com>
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220706134132.3623415-3-stephan.gerhold@kernkonzept.com
Convert the clock driver to specify parent data rather than parent
names, to actually bind using 'clock-names' specified in the DTS rather
than global clock names. Use parent_hws where possible to refer parent
clocks directly, skipping the lookup.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: David Heidelberg <david@ixit.cz> # tested on Nexus 7 (2013)
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220623120418.250589-10-dmitry.baryshkov@linaro.org
Move clock parent tables down, after the PLL declrataions, so that we
can use pll hw clock fields in the next commit.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: David Heidelberg <david@ixit.cz> # tested on Nexus 7 (2013)
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220623120418.250589-9-dmitry.baryshkov@linaro.org
Convert the clock driver to specify parent data rather than parent
names, to actually bind using 'clock-names' specified in the DTS rather
than global clock names. Use parent_hws where possible to refer parent
clocks directly, skipping the lookup.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: David Heidelberg <david@ixit.cz> # tested on Nexus 7 (2013)
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220623120418.250589-7-dmitry.baryshkov@linaro.org
Split and extend existing CLK_AIF_OSR_DIV macro to implement mi2s
clocks. This simplifies the driver and removes extra code duplication.
The clock mi2s_div_clk used .enable_reg/.enable_bit, however these
fields are not used with by the clk_regmap_div_ops, thus they are
silently dropped. Clock enablement is handled in the mi2s_bit_div_clk
clock.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: David Heidelberg <david@ixit.cz> # tested on Nexus 7 (2013)
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220623120418.250589-6-dmitry.baryshkov@linaro.org
Convert the clock driver to specify parent data rather than parent
names, to actually bind using 'clock-names' specified in the DTS rather
than global clock names. Use parent_hws where possible to refer parent
clocks directly, skipping the lookup.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: David Heidelberg <david@ixit.cz> # tested on Nexus 7 (2013)
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220623120418.250589-5-dmitry.baryshkov@linaro.org
By the clk framework already reference counts prepare/unprepare,
this if statement should be never true.
Signed-off-by: Li Zhengyu <lizhengyu3@huawei.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20220613063327.89320-1-lizhengyu3@huawei.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The Snapdragon 670 adds and removes some clocks, adds new frequencies, and
adds a new GPLL (Global Phase-Locked Loop) in reference to SDM845, while
also removing some GDSCs. Despite these differences, there are many
similarities with SDM670. Add data for SDM670 in the driver for SDM845 to
reuse the most of the clock data.
Advantages and disadvantages of this approach:
+ maintenance applies to both sdm670 and sdm845 by default
+ less duplicate code (clocks) means smaller distro/pre-built kernels
with all drivers enabled
- clocks for both SoC's must be compiled if the user wants clocks for one
specific SoC (both or none)
- additional testing needed for sdm845 devices
Link: 443bd8d6e2%5E%21/#F10
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220914013922.198778-4-mailingradian@gmail.com
This driver will support more than one SoC's set of clocks, and set of
GDSCs. This behavior would be unclean with hard-coded static variables.
Support it by grabbing clocks, GDSCs, and BCRs in the match data.
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220914013922.198778-3-mailingradian@gmail.com
Change a53-pll driver to use clk_parent_data rather than always looking
up the xo clock in the system clock list.
Note, this change also switches the a53-pll from the global `xo' clock
to the `xo_board', the clock that is specified as the `xo' clock in the
DT file.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220909103137.3727830-1-dmitry.baryshkov@linaro.org
Convert the clock driver to specify parent data rather than parent
names, to actually bind using 'clock-names' specified in the DTS rather
than global clock names. Use parent_hws where possible to refer parent
clocks directly, skipping the lookup.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220909105136.3733919-4-dmitry.baryshkov@linaro.org
