Make Kconfig and Makefile more generic to encompass not only
OMAP4 but other OMAP processors featuring HDMI.
Also, relax the dependency list to depend only on any OMAP processor
supporting OMAP2_DSS and OMAP4_DSS_HDMI. As HDMI support for
future OMAP versions is added, the dependency list must change
accordingly.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
According to the HDMI specification, a source is permitted to
transmit L-PCM audio in the following sample rates: 32kHz, 44.1kHz,
48kHz, 88.2kHz, 96kHz, 176.4kHz or 192kHz.
It also supports up to 8 audio channels.
The sink may not necessarily support all these sample rates and
channels. However, as this CPU DAI describes the HDMI source, it
makes sense to include them. The limitation of capabilities as
supported by the sink should be done in the ASoC HDMI codec.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Before starting to play audio, we need to make sure that the
display is active and the current video mode supports audio. instead
of using the overlay manager in the machine driver, we use the DSS audio
interface's audio_supported function. As we already have a pointer to
the correct dssdev, we do not have to look for it every time audio is
to be played. Also, the CPU DAI startup function is called earlier
than the card hw_param function. Hence and we can detect the state of
the display earlier.
While there, add a error message if the constraint cannot be applied.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
squash to improve err
Signed-off-by: Liam Girdwood <lrg@ti.com>
Expand the configuration of the hw_params to include the IEC-60958
channel status word and the CEA-861 audio infoframe. The configuration
of such structures depends on the snd_pcm_hw_params received. A
omap_dss_audio is used to pass the configuration parameters to DSS.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Instead of accessing the HDMI IP directly, the CPU DAI driver takes
advantage of the audio interface provided by the DSS device driver.
The ASoC driver will link the DSS audio functionality with ALSA by
calling the appropriate DSS device driver functions at the relevant
moments. For this, three new DAI operations are added: trigger, prepare
and shutdown operations.
At the moment, it is assumed that only one HDMI display is available
in the system, as it is the case in OMAP4. However, in the future,
one DAI for each HDMI display should be provided.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Create a struct hdmi_priv to store the relevant data of the CPU DAI
driver. As more data is added to the driver, having all the data
in the same location eases its handling. At the moment, only the DMA
configuration parameters are included in the structure.
Also, the required memory is allocated using devm_kzalloc rather than
using a static global variable.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
When getting the needed resources fails, return -ENODEV. This is more
in line with other drivers do and it gives a more descriptive error.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
In order to utilize the new OMAP HDMI codec and the updated name of
the device of the CPU DAI, update the names at the drivers accordingly.
While there, also update the name of the machine driver to be more
generic and encompass more OMAP processors featuring HDMI and not
only OMAP4.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
In preparation to Device Tree support.
With DT booted kernel we can not rely on pdata which used to
hold information needed for the driver at runtime.
Use the card's driver data to hold these informations from now on.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
The needed change in routing will be done runtime for the non
twl6040 connected widgets, like the Digital microphone.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
There is no need to have two snd_soc_dai_link structure for the two setup
the machine driver supports.
We can just tell core to register only the first link if the DMIC link is
not in use on the device.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Device tree support for OMAP4+ dmic cpu dai driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Device tree support for OMAP4+ McPDM cpu dai driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
In capture stream the buffer size does not need to be constrained to be
bigger then the McBSP FIFO.
In capture the FIFO content is taken out in period length burst, this
enusres that the FIFO is not going to overflow.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
With the common irq the driver only needs to use one interrupt line, and
it provides better debugging possibilites compared to the legacy TX/RX
interrupt lines.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
The frame dma_op_mode has never been used, and it is just creating
confusion for users/developers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Take the DMA packet mode into use when the McBSP is configured in element
dma_op_mode if the stream is not mono.
In this way we transfer one sample from/to McBSP FIFO upon DMA request.
This change only affects OMAP3+ versions, where the McBSP ports have FIFO.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
SupherH FSI2 can use special data transfer,
but it depends on CPU-FSI2 connection style.
We can use 16bit data stream mode if it was valid connection,
and it is required for 16bit data DMA transfer / SPDIF sound output.
We can use 24bit data transfer if it was invalid connection.
We can select connection type if CPU is SH7372,
and it is always valid connection if latest SuperH.
This patch adds new bus_option and fsi_bus_setup()
for supporting these feature.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
fsi_hw_startup/shutdown() needs the setup of bus width,
but it is impossible to get parameter of snd_pcm_runtime at this timing.
So, these functions are changed so that be called from fsi_dai_trigger().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds fsi_version() function for accessing version.
And there were some meaningless version check which never hit.
This patch removed it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Introduce codec for HDMI. At the moment, this is a dummy codec. In the
future it will parse the EDID to modify the supported parameters, such
as the number of channels and the sample rates. At the moment, it blindly
supports all the sample rates and audio channels described in the HDMI
1.4a specification.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Philippe Rétornaz <philippe.retornaz@epfl.ch>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Philippe Rétornaz <philippe.retornaz@epfl.ch>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 4924082 "ASoC: core: Flip master for CODECs in the CPU slot of a
CODEC<->CODEC link" added code that was conditional on there being no
PCM/DMA driver for the link. However, it failed to cover the case where
the link was instantiated from device tree, and hence was specified by
DT node rather than name.
This prevents the following error on Toshiba AC100:
aplay: pcm_write:1603: write error: Input/output error
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
aic3x_set_headset_detection() isn't made available outside the driver or
referenced within the driver which sparse notices and complains about.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In preparation for irq_domain support change the code to the not switch
based on the irq number. This actually makes things simpler, if slightly
repetitive.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
I was hoping to be done with fixes for 3.4 but we got two branches from
subarch maintainers the last couple of days. So here is one last(?) pull
request for arm-soc containing 7 patches:
- 5 of them are for shmobile dealing with SMP setup and compile failures
- The remaining two are for regressions on the Samsung platforms
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Q2un
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM: SoC fixes from Olof Johansson:
"I was hoping to be done with fixes for 3.4 but we got two branches
from subarch maintainers the last couple of days. So here is one
last(?) pull request for arm-soc containing 7 patches:
- Five of them are for shmobile dealing with SMP setup and compile
failures
- The remaining two are for regressions on the Samsung platforms"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: EXYNOS: fix ctrlbit for exynos5_clk_pdma1
ARM: EXYNOS: use s5p-timer for UniversalC210 board
ARM / mach-shmobile: Invalidate caches when booting secondary cores
ARM / mach-shmobile: sh73a0 SMP TWD boot regression fix
ARM / mach-shmobile: r8a7779 SMP TWD boot regression fix
ARM: mach-shmobile: convert ag5evm to use the generic MMC GPIO hotplug helper
ARM: mach-shmobile: convert mackerel to use the generic MMC GPIO hotplug helper
An OMAP bug fix, a set of PCH bug fixes, and one patch to fix up compile
warnings
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=P8v+
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull a few more GPIO bug fixes from Grant Likely:
"Oops, missed a couple. Here's an updated pull req for GPIO"
A set of PCH bug fixes, and one patch to fix up compile warnings
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6:
gpio/exynos: Fix compiler warnings when non-exynos machines are selected
gpio: pch9: Use proper flow type handlers
* 'v3.4-samsung-fixes-5' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: fix ctrlbit for exynos5_clk_pdma1
ARM: EXYNOS: use s5p-timer for UniversalC210 board
Commit 069d4e743 ("ARM: EXYNOS4: Remove clock event timers using
ARM private timers") removed support for local timers and forced
to use MCT as event source. However MCT is not operating properly
on early revision of EXYNOS4 SoCs. All UniversalC210 boards are
based on it, so that commit broke support for it. This patch
provides a workaround that enables UniversalC210 boards to boot
again. s5p-timer is used as an event source, it works only for
non-SMP builds.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
By Guennadi Liakhovetski (2) and others via Rafael J. Wysocki:
"[...] urgent fixes for Renesas ARM-based platforms. Four of these
commits are fixes of regressions new in 3.4-rc and the last one is
necessary for SMP to work on those systems in general."
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/renesas:
ARM / mach-shmobile: Invalidate caches when booting secondary cores
ARM / mach-shmobile: sh73a0 SMP TWD boot regression fix
ARM / mach-shmobile: r8a7779 SMP TWD boot regression fix
ARM: mach-shmobile: convert ag5evm to use the generic MMC GPIO hotplug helper
ARM: mach-shmobile: convert mackerel to use the generic MMC GPIO hotplug helper
Make sure L1 caches are invalidated when booting secondary
cores. Needed to boot all mach-shmobile SMP systems that
are using Cortex-A9 including sh73a0, r8a7779 and EMEV2.
Thanks to imx and tegra guys for actual code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Fix SMP TWD boot regression on sh73a0 based platforms caused by:
4200b16 ARM: shmobile: convert to twd_local_timer_register() interface
After the merge of the above commit it has been impossible to boot
sh73a0 based SoCs with SMP enabled and CONFIG_HAVE_ARM_TWD=y. The
kernel crashes at smp_init_cpus() timing which is before the console
has been initialized, so to the user this looks like a kernel lock up
without any particular error message.
This patch fixes the regression on sh73a0 by moving the TWD
registration code from smp_init_cpus() to sys_timer->init() time.
This patch removed shmobile_twd_init() which is no longer needed
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Fix SMP TWD boot regression on r8a7779 based platforms caused by:
4200b16 ARM: shmobile: convert to twd_local_timer_register() interface
After the merge of the above commit it has been impossible to boot
r8a7779 based SoCs with SMP enabled and CONFIG_HAVE_ARM_TWD=y. The
kernel crashes at smp_init_cpus() timing which is before the console
has been initialized, so to the user this looks like a kernel lock up
without any particular error message.
This patch fixes the regression on r8a7779 by moving the TWD
registration code from smp_init_cpus() to sys_timer->init() time.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This also fixes the following modular mmc build failure:
arch/arm/mach-shmobile/built-in.o: In function `mackerel_sdhi0_gpio_cd':
pfc-sh7372.c:(.text+0x1138): undefined reference to `mmc_detect_change'
on this platform by eliminating the use of an inline function, which
calls into the mmc core.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
