The biggest set of changes in here is the addition of the Qualcomm RPMH
driver. As well as the regualtor driver itself being quite large due to
the usual involved Qualcomm regulator stuff there's also some code
shared with the arm-soc tree, a bus driver required to communicate with
the hardware that actually winds up being much larger than the regulator
driver itself and a LLCC driver that was part of the same signed tag
used with the arm-soc tree.
Other than that it's a fairly standard and quiet release, highlights
include:
- Addition of device links from regulator consumers to their
regulators, helping the core avoid dependency issues during suspend.
- Support for the entertainingly innovative suspend implementation in
the BD9571MWV.
- Support for switch regulators on the PFUZE100, this required two goes
due to backwards compatibility issues with old DTs that were
discovered.
- Support for Freescale PFUZE3001 and SocioNext UniPhier.
- The aforementioned Qualcomm RPMH driver together with the driver
changes required to support it.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAltxi/ATHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0GNxB/99LLeB+gfD4ckoU07Az/k77+CfIZ8D
HEUA9ryP4y6isUxpZMGcZhKa48ag9RxTuAGK+gGWtKUHxPIH6o0CuRLbGm3GOo99
MTbbMaJRJIHkwsh8XjX2Adr02XSzU/9r2T3rpZD10T/J1Qj1D3W1YuvaE/fQuOII
XW8QWhRuTWbVI/gSIEj+o2PcVK77yb9Nr+llNvS+BOlFAlnNo1tx3qCJ1bUiVEyD
DhLkL0n0XfaOpbtZV5DIsVDiMsB+/TnXtqiijfvq0qi5SHh6jECpQYNWHBNyIkwj
4N9NQ9xfC6bArAl9tWxXvJrVXUqFSRagHeB2xLD6piWcZ0DC4K0QfEW2
=WiXl
-----END PGP SIGNATURE-----
Merge tag 'regulator-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"The biggest set of changes in here is the addition of the Qualcomm
RPMH driver. As well as the regualtor driver itself being quite large
due to the usual involved Qualcomm regulator stuff there's also some
code shared with the arm-soc tree, a bus driver required to
communicate with the hardware that actually winds up being much larger
than the regulator driver itself and a LLCC driver that was part of
the same signed tag used with the arm-soc tree.
Other than that it's a fairly standard and quiet release, highlights
include:
- Addition of device links from regulator consumers to their
regulators, helping the core avoid dependency issues during
suspend.
- Support for the entertainingly innovative suspend implementation in
the BD9571MWV.
- Support for switch regulators on the PFUZE100, this required two
goes due to backwards compatibility issues with old DTs that were
discovered.
- Support for Freescale PFUZE3001 and SocioNext UniPhier.
- The aforementioned Qualcomm RPMH driver together with the driver
changes required to support it"
* tag 'regulator-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (52 commits)
regulator: add QCOM RPMh regulator driver
regulator: dt-bindings: add QCOM RPMh regulator bindings
regulator: samsung: Add SPDX license identifiers
regulator: maxim: Add SPDX license identifiers
regulator: bd71837: adobt MFD changes to regulator driver
regulator: tps65217: Fix NULL pointer dereference on probe
regulator: Add support for CPCAP regulators on Motorola Xoom devices.
regulator: Add sw2_sw4 voltage table to cpcap regulator.
regulator: bd9571mwv: Make symbol 'dev_attr_backup_mode' static
regulator: pfuze100: add support to en-/disable switch regulators
regulator: pfuze100: add optional disable switch-regulators binding
soc: qcom: rmtfs-mem: fix memleak in probe error paths
soc: qcom: llc-slice: Add missing MODULE_LICENSE()
drivers: qcom: rpmh: fix unwanted error check for get_tcs_of_type()
drivers: qcom: rpmh-rsc: fix the loop index check in get_req_from_tcs
firmware: qcom: scm: add a dummy qcom_scm_assign_mem()
drivers: qcom: rpmh-rsc: Check cmd_db_ready() to help children
drivers: qcom: rpmh-rsc: allow active requests from wake TCS
drivers: qcom: rpmh: add support for batch RPMH request
drivers: qcom: rpmh: allow requests to be sent asynchronously
...
Several small new features for regmap this time around:
- Support for SCCB, an I2C variant used on some media cards. This has
also pulled in an I2C commit from Peter Rosin as a dependency.
- Addition of an API for reading repeatedly from registers where the
address doesn't automatically increment like some ADC outputs or GPIO
status registers.
- Support for bulk I/O on Slimbus.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAltxUxYTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0B26B/9A/Q9P+92i0LZ2ecO3QltvPeIP46jR
gnS3WEmgMk/yIWR9wusF3Ju4gfTZ4L5DEkl+5iooqlg54e3c8l3OdDIsRXXiLtIK
+BOU9xW4u4sdmGjuXqkkGCWgz75r/Em07Z4y3pB5kl/KHGtQPOrrvS8/33ETjhKC
tg/SC8bdJ6ZSC2J1lVYA+IolNfVt0rvjY3TdXwm0qel9SmQIqrL8xilj/JV8Hmhg
6PSH9PIoIkSRgvqp1N0IOysVcDcwgjAEyg3eeH+L2S0y/YMPY88ndf7d8mpWdkzQ
KGEUxgB+qWBHMjRKTgu4sqal1KZxCPghxO5kRn4UBaZsxFDdnXbtDcRQ
=e1ml
-----END PGP SIGNATURE-----
Merge tag 'regmap-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"Several small new features for regmap this time around:
- Support for SCCB, an I2C variant used on some media cards. This has
also pulled in an I2C commit from Peter Rosin as a dependency.
- Addition of an API for reading repeatedly from registers where the
address doesn't automatically increment like some ADC outputs or
GPIO status registers.
- Support for bulk I/O on Slimbus"
* tag 'regmap-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: Add regmap_noinc_read API
regmap: sccb: fix typo and sort headers alphabetically
i2c: smbus: add unlocked __i2c_smbus_xfer variant
regmap: add SCCB support
regmap: slimbus: add support to multi read/write
Merge changes in the PM core, system-wide PM infrastructure, generic
power domains (genpd) framework, ACPI PM infrastructure and cpuidle
for 4.19.
* pm-core:
driver core: Add flag to autoremove device link on supplier unbind
driver core: Rename flag AUTOREMOVE to AUTOREMOVE_CONSUMER
* pm-domains:
PM / Domains: Introduce dev_pm_domain_attach_by_name()
PM / Domains: Introduce option to attach a device by name to genpd
PM / Domains: dt: Add a power-domain-names property
* pm-sleep:
PM / reboot: Eliminate race between reboot and suspend
PM / hibernate: Mark expected switch fall-through
x86/power/hibernate_64: Remove VLA usage
PM / hibernate: cast PAGE_SIZE to int when comparing with error code
* acpi-pm:
ACPI / PM: save NVS memory for ASUS 1025C laptop
ACPI / PM: Default to s2idle in all machines supporting LP S0
* pm-cpuidle:
ARM: cpuidle: silence error on driver registration failure
Some devices have individual registers that don't autoincrement the
register address during bulk reads but instead repeatedly read the same
value, for example for monitoring GPIOs or ADCs. Add support for these.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAltsE8YTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0DeLB/sHEWAdyUCz9dO9pDdpi6WfpnKXuCCd
ZFnx8VXBvzVLRCZYGXuMOUEzBQU2lTr2KPFDmE1k4FclyiWaI+hRIJ0s/x8FAl51
EFDoR4TM7t2n2aY0sPQCZKnoAhdQ9YPxlA9JjDUE57h0KoC76Dh8OB44dlAlxUAY
PUjkv64/7AtvkBX7UZPQxckaPOLKM00P/hXwCB9MZCkjqnSWkUGgNCWPgKn9j2yL
jiUQO0Wo9u8RkvYvndHPkh4NzgeH1sUFUdNys/Fopu6C2miIYBNKzvEo2OXhelHf
k5rsoMQXYdiPdy4vRbeaWFetyEeBjxKIAQHKD0WJviFPw8j+ET+2GNjx
=p0Mu
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAltsFCwTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0NcxB/wMqH+78D7GdJfMkxMKhCHFUxozfCe9
cgWgZ7+vlWpIwEGvM65FHMrFyc5ZrS3/vD6Hy8lqpsqGBVv6wS6Z0lsoOyj/QvTl
T8USWKvQnvtzlPY5lRZL0xuGiaGGtpGa0eaLKH2lY7uvoge0oHz8VV6ar5y7eA1S
1INBpgTdHJgCQLZoc1pFNOcZ0EMFl6ZAygIWJTpqIwoQlvPEgtCQ4wjPlMUKrevP
psJWd9obyM6+02mYFVMAlYpcMSoZ/MjPeMb7VGhLGwA1BA6dNcbiIeS7GCeH2r/i
/vxvarsEm38MfLBIyORW06onHyRhVwXdLoD1jblmvYtRlfW5ANjr5g/O
=mbi1
-----END PGP SIGNATURE-----
Merge tag 'regmap-noinc-read' into regmap-4.19
regmap: Support non-incrementing registers
Some devices have individual registers that don't autoincrement the
register address during bulk reads but instead repeatedly read the same
value, for example for monitoring GPIOs or ADCs. Add support for these.
The regmap API usually assumes that bulk read operations will read a
range of registers but some I2C/SPI devices have certain registers for
which a such a read operation will return data from an internal FIFO
instead. Add an explicit API to support bulk read without range semantics.
Some linux drivers use regmap_bulk_read or regmap_raw_read for such
registers, for example mpu6050 or bmi150 from IIO. This only happens to
work because when caching is disabled a single regmap read op will map
to a single bus read op (as desired). This breaks if caching is enabled and
reg+1 happens to be a cacheable register.
Without regmap support refactoring a driver to enable regmap caching
requires separate I2C and SPI paths. This is exactly what regmap is
supposed to help avoid.
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The BTF conflicts were simple overlapping changes.
The virtio_net conflict was an overlap of a fix of statistics counter,
happening alongisde a move over to a bonafide statistics structure
rather than counting value on the stack.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a single driver core fix for 4.18-rc7. It partially reverts a
previous commit to resolve some reported issues.
It has been in linux-next for a while now with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW1nVXg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylt+ACgnOBM409ab+U2z/0EZcJrd3fXjXcAn1XD1e5p
Y0fBLaJ/sB+VpyiRP/gK
=WxMr
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fix from Greg KH:
"This is a single driver core fix for 4.18-rc7. It partially reverts a
previous commit to resolve some reported issues.
It has been in linux-next for a while now with no reported issues"
* tag 'driver-core-4.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
driver core: Partially revert "driver core: correct device's shutdown order"
Fix typos 's/wit/with/' in the comments and sort headers alphabetically
in order to avoid duplicate includes in future.
Fixes: bcf7eac3d9 ("regmap: add SCCB support")
Reported-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In some cases the link between between customer and supplier
already exist, for example when a device use its parent as a supplier.
Do not warn about already existing dependencies because device_link_add()
takes care of this case.
Link: http://lkml.kernel.org/r/20180709111753eucas1p1f32e66fb2f7ea3216097cd72a132355d~-rzycA5Rg0378203782eucas1p1C@eucas1p1.samsung.com
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Reviewed-by: Rafael J. Wysocki <rafael@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a race window in device_shutdown(), which may cause
-1. parent device shut down before child or
-2. no shutdown on a new probing device.
For 1st, taking the following scenario:
device_shutdown new plugin device
list_del_init(parent_dev);
spin_unlock(list_lock);
device_add(child)
probe child
shutdown parent_dev
--> now child is on the tail of devices_kset
For 2nd, taking the following scenario:
device_shutdown new plugin device
device_add(dev)
device_lock(dev);
...
device_unlock(dev);
probe dev
--> now, the new occurred dev has no opportunity to shutdown
To fix this race issue, just prevent the new probing request. With this
logic, device_shutdown() is more similar to dpm_prepare().
Signed-off-by: Pingfan Liu <kernelfans@gmail.com>
Reviewed-by: Rafael J. Wysocki <rafael@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Plumb in get_ownership() callback for devices belonging to a class so that
they can be created with uid/gid different from global root. This will
allow network devices in a container to belong to container's root and not
global root.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Tyler Hicks <tyhicks@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an I2C subset.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAltPUrMTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0KODB/oDV+4c82VIUopoaXxK8PbBqDMn5n2r
EKyb1D/GFiT54x2666arRT1NymL/uk6/nK1hryd/4HE5zB1lUQnu/Z7HCHgF4N+/
iWHtAgFUSZtNlMTRT6DW/tcsNDGnH9vjNJUhOLH9Y21h3Q4BpOo5HQVR8ynN4TDh
2inSy5qgADyrosxRpW5mp0Nt0tpFTfvYOHoRaLTbQUbBnpb/MmqcTzkYHcVNqA8V
7+e9/SOVU0XXHQD5k28F7eB84Mk+TXQrZQ181RwNOKUf3je86Im6WfrFqKHqKP5N
UAq28AjsjRiBs1qwOYK0ytWR8gQvs39cZmdud507R1mLWEO4/++TruRt
=wkUm
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAltPUyETHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0CJsB/oD+83KWX8V1Q4HhaO3e6BN2SPYphQr
jbImC9QUSRl/65+0ek6VjqLu4znY/LARRjNThN0l01wvWv7+h71DJBSKL67zK9en
h4Lr8ZoewBQ408YaC5zl7ilFXgRBMhfCanDWWHv8jAv1rk9VQU8q9uNGo518e0Ks
2Gg/zTmQYp7dNMHsVO4AEr3UQye1yZdGdP1q1yk3nbNgZbDq4xWWZWl1p4Iy+QG3
e4SY+OYenQC/+pafUQOzPoiG3I/f8RAQG9SAtne+gtIyF85+Q8mVizuU89GdtH3O
rKcaiNk/FpSbcBxAXEGb0qNy6PW6gnAbSznrOdc7MEj2V5E3KfoR7oVO
=VO/+
-----END PGP SIGNATURE-----
Merge tag 'regmap-sccb' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap into regmap-4.19
regmap: Add support for SCCB
This is an I2C subset.
This adds Serial Camera Control Bus (SCCB) support for regmap API that
is intended to be used by some of Omnivision sensor drivers.
The ov772x and ov9650 drivers are going to use this SCCB regmap API.
The ov772x driver was previously only worked with the i2c controller
drivers that support I2C_FUNC_PROTOCOL_MANGLING, because the ov772x
device doesn't support repeated starts. After commit 0b964d183c
("media: ov772x: allow i2c controllers without
I2C_FUNC_PROTOCOL_MANGLING"), reading ov772x register is replaced with
issuing two separated i2c messages in order to avoid repeated start.
Using this SCCB regmap hides the implementation detail.
The ov9650 driver also issues two separated i2c messages to read the
registers as the device doesn't support repeated start. So it can
make use of this SCCB regmap.
Cc: Mark Brown <broonie@kernel.org>
Cc: Peter Rosin <peda@axentia.se>
Cc: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Jacopo Mondi <jacopo+renesas@jmondi.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For devices with a class, we create a "glue" directory between
the parent device and the new device with the class name.
This directory is never "explicitely" removed when empty however,
this is left to the implicit sysfs removal done by kobject_release()
when the object loses its last reference via kobject_put().
This is problematic because as long as it's not been removed from
sysfs, it is still present in the class kset and in sysfs directory
structure.
The presence in the class kset exposes a use after free bug fixed
by the previous patch, but the presence in sysfs means that until
the kobject is released, which can take a while (especially with
kobject debugging), any attempt at re-creating such as binding a
new device for that class/parent pair, will result in a sysfs
duplicate file name error.
This fixes it by instead doing an explicit kobject_del() when
the glue dir is empty, by keeping track of the number of
child devices of the gluedir.
This is made easy by the fact that all glue dir operations are
done with a global mutex, and there's already a function
(cleanup_glue_dir) called in all the right places taking that
mutex that can be enhanced for this. It appears that this was
in fact the intent of the function, but the implementation was
wrong.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
device_private_init is called only in core.c, extern declare is
unnecessary and make it static.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SLIMbus supports upto 16 bytes in value management messages,
so add support to read/writes upto 16 bytes.
This also removes redundant single register reg_read/reg_write.
Also useful for paged register access on SLIMbus interfaced codecs.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 52cdbdd498 (driver core: correct device's shutdown order)
introduced a regression by breaking device shutdown on some systems.
Namely, the devices_kset_move_last() call in really_probe() added by
that commit is a mistake as it may cause parents to follow children
in the devices_kset list which then causes shutdown to fail. For
example, if a device has children before really_probe() is called
for it (which is not uncommon), that call will cause it to be
reordered after the children in the devices_kset list and the
ordering of that list will not reflect the correct device shutdown
order any more.
Also it causes the devices_kset list to be constantly reordered
until all drivers have been probed which is totally pointless
overhead in the majority of cases and it only covered an issue
with system shutdown, while system-wide suspend/resume potentially
had the same issue on the affected platforms (which was not covered).
Moreover, the shutdown issue originally addressed by the change in
really_probe() made by commit 52cdbdd498 is not present in 4.18-rc
any more, since dra7 started to use the sdhci-omap driver which
doesn't disable any regulators during shutdown, so the really_probe()
part of commit 52cdbdd498 can be safely reverted. [The original
issue was related to the omap_hsmmc driver used by dra7 previously.]
For the above reasons, revert the really_probe() modifications made
by commit 52cdbdd498.
The other code changes made by commit 52cdbdd498 are useful and
they need not be reverted.
Fixes: 52cdbdd498 (driver core: correct device's shutdown order)
Link: https://lore.kernel.org/lkml/CAFgQCTt7VfqM=UyCnvNFxrSw8Z6cUtAi3HUwR4_xPAc03SgHjQ@mail.gmail.com/
Reported-by: Pingfan Liu <kernelfans@gmail.com>
Tested-by: Pingfan Liu <kernelfans@gmail.com>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All PM domain drivers must be built-in (at least those using DT), so
there is no point deferring probe after initcalls are done. Continuing
to defer probe may prevent booting successfully even if managing PM
domains is not required. This can happen if the user failed to enable
the driver or if power-domains are added to a platform's DT, but there
is not yet a driver (e.g. a new DTB with an old kernel).
Call the driver core function driver_deferred_probe_check_init_done()
instead of just returning -EPROBE_DEFER to stop deferring probe when
initcalls are done.
Acked-by: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Kevin Hilman <khilman@kernel.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Len Brown <len.brown@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Deferred probe will currently wait forever on dependent devices to probe,
but sometimes a driver will never exist. It's also not always critical for
a driver to exist. Platforms can rely on default configuration from the
bootloader or reset defaults for things such as pinctrl and power domains.
This is often the case with initial platform support until various drivers
get enabled. There's at least 2 scenarios where deferred probe can render
a platform broken. Both involve using a DT which has more devices and
dependencies than the kernel supports. The 1st case is a driver may be
disabled in the kernel config. The 2nd case is the kernel version may
simply not have the dependent driver. This can happen if using a newer DT
(provided by firmware perhaps) with a stable kernel version. Deferred
probe issues can be difficult to debug especially if the console has
dependencies or userspace fails to boot to a shell.
There are also cases like IOMMUs where only built-in drivers are
supported, so deferring probe after initcalls is not needed. The IOMMU
subsystem implemented its own mechanism to handle this using OF_DECLARE
linker sections.
This commit adds makes ending deferred probe conditional on initcalls
being completed or a debug timeout. Subsystems or drivers may opt-in by
calling driver_deferred_probe_check_init_done() instead of
unconditionally returning -EPROBE_DEFER. They may use additional
information from DT or kernel's config to decide whether to continue to
defer probe or not.
The timeout mechanism is intended for debug purposes and WARNs loudly.
The remaining deferred probe pending list will also be dumped after the
timeout. Not that this timeout won't work for the console which needs
to be enabled before userspace starts. However, if the console's
dependencies are resolved, then the kernel log will be printed (as
opposed to no output).
Cc: Alexander Graf <agraf@suse.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a flag to autoremove the device links on supplier driver
unbind. This obviates the need to explicitly delete the link
in the remove path.
We remove these links only when the supplier's link to its
consumers has gone to DL_STATE_SUPPLIER_UNBIND state.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Suggested-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Now that we want to add another flag to autoremove the device link
on supplier unbind, it's fair to rename the existing flag from
DL_FLAG_AUTOREMOVE to DL_FLAG_AUTOREMOVE_CONSUMER so that we can
add similar flag for supplier later.
And, while we are touching device.h, fix a doc build warning.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
For the multiple PM domain case, let's introduce a new API called
dev_pm_domain_attach_by_name(). This allows a consumer driver to associate
its device with one of its PM domains, by using a name based lookup.
Do note that, currently it's only genpd that supports multiple PM domains
per device, but dev_pm_domain_attach_by_name() can easily by extended to
cover other PM domain types, if/when needed.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
For the multiple PM domain case, let's introduce a new function called
genpd_dev_pm_attach_by_name(). This allows a device to be associated with
its PM domain through genpd, by using a name based lookup.
Note that, genpd_dev_pm_attach_by_name() shall only be called by the driver
core / PM core, similar to how the existing dev_pm_domain_attach_by_id()
makes use of genpd_dev_pm_attach_by_id(). However, this is implemented by
following changes on top.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
With Device Trees (DT), the dependencies of the devices are defined in the
DT, then the drivers parse that information to lookup the needed resources
that have as dependencies.
Since drivers and devices are registered in a non-deterministic way, it is
possible that a device that is a dependency has not been registered yet by
the time that is looked up.
In this case the driver that requires this dependency cannot probe and has
to defer it. So the driver core adds it to a list of deferred devices that
is iterated again every time that a new driver is probed successfully.
For debugging purposes it may be useful to know what are the devices whose
probe function was deferred. Add a debugfs entry showing that information.
$ cat /sys/kernel/debug/devices_deferred
48070000.i2c:twl@48:bci
musb-hdrc.0.auto
omapdrm.0
This information could be obtained partially by enabling debugging, but it
means that the kernel log has to be parsed and the probe deferral balanced
with the successes. This can be error probe and has to be done in a ad-hoc
manner by everyone who needs to debug these kind of issues.
Since the information is already known by the kernel, just show it to make
it easier to debug.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes: [ 0.010000] cpu cpu0: Error -2 creating of_node link
... which you get for every CPU on all architectures that use
CONFIG_GENERIC_CPU_DEVICES.
In that case, driver_init() calls cpu_dev_init() before calling
of_core_init(). Then we get the callchain:
cpu_dev_init()
-> cpu_dev_register_generic()
-> register_cpu(cpu, i)
-> device_register(&cpu->dev)
-> device_add(dev)
-> device_add_class_symlinks(dev)
... in device_add_class_symlinks, we we dev->of_node, and call
sysfs_create_link(), which fails because we haven't called
of_core_init() to register the sysfs devicetree directory yet.
Signed-off-by: Wesley W. Terpstra <wesley@sifive.com>
[hch: updated the changelog based on review feedback]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Frank Rowand <frowand.list@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_property_read_u32 searches for a property in a device node and read
a 32-bit value from it. Instead of using of_get_property to get the
property and then read 32-bit value using of_read_number, we can
simplify it by using of_property_read_u32.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a prefixing macro to dev_<level> uses similar to the pr_fmt
prefixing macro used in pr_<level> calls.
This can help avoid some string duplication in dev_<level> uses.
The default, like pr_fmt, is an empty #define dev_fmt(fmt) fmt
Rename the existing dev_<level> functions to _dev_<level> and
introduce #define dev_<level> _dev_<level> macros that use the
new #define dev_fmt
Miscellanea:
o Consistently use #defines with fmt, ... and ##__VA_ARGS__
o Remove unnecessary externs
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add initcall_debug logs for each driver device probe call, for example:
probe of a3800000.ramoops returned 1 after 3007 usecs
This replaces the previous code added to report times for deferred
probes. It also reports OF platform bus device creates that were
formerly lumped together in a single entry for function
of_platform_default_populate_init, as well as helping to annotate other
initcalls that involve device probing.
Remove restriction on printing probe times only during initcalls, since
initcall_debug now continues to show driver timing info past the boot
phase.
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Device_link_remove uses the same arguments than device_link_add. The Goal
is to avoid storing the link pointer.
Signed-off-by: pascal paillet <p.paillet@st.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are no legacy behavior in drivers to consider while attaching a
device to genpd - for the multiple PM domain case.
For that reason, let's instead require the driver to runtime resume the
device, via calling pm_runtime_get_sync() for example, when it needs to
power on the corresponding PM domain.
This allows us to improve the situation during attach. Instead of always
power on the PM domain, which may be unnecessary, let's leave it in its
current state. Additionally, to avoid the PM domain to stay powered on,
let's schedule a power off work.
Fixes: 3c095f32a9 (PM / Domains: Add support for multi PM domains ...)
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The DT node passed here isn't necessarily an OPP node, as this routine
can also be used for cases where the "required-opps" property is present
directly in the device's node. Rename it.
This also removes a stale comment.
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Fix the PM core to avoid introducing a runtime PM usage counter
imbalance when adding device links during driver probe (Rafael
Wysocki).
- Fix the operating performance points (OPP) framework to ensure
that the regulator voltage is always updated as appropriate when
updating clock rates (Waldemar Rymarkiewicz).
- Fix the intel_pstate driver to use correct max/min limits for
cores with differing maximum frequences (Srinivas Pandruvada).
- Fix a typo in the intel_pstate driver documentation (Rafael
Wysocki).
- Fix two issues with the recently added Kryo cpufreq driver (Ilia
Lin).
- Fix two recent regressions and some other minor issues in the
turbostat utility and extend it to provide some more diagnostic
information (Len Brown, Nathan Ciobanu).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=QQoY
-----END PGP SIGNATURE-----
Merge tag 'pm-4.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These are mostly fixes, including some fixes for changes made during
the recent merge window and some "stable" material, plus some minor
extensions of the turbostat utility.
Specifics:
- Fix the PM core to avoid introducing a runtime PM usage counter
imbalance when adding device links during driver probe (Rafael
Wysocki).
- Fix the operating performance points (OPP) framework to ensure that
the regulator voltage is always updated as appropriate when
updating clock rates (Waldemar Rymarkiewicz).
- Fix the intel_pstate driver to use correct max/min limits for cores
with differing maximum frequences (Srinivas Pandruvada).
- Fix a typo in the intel_pstate driver documentation (Rafael
Wysocki).
- Fix two issues with the recently added Kryo cpufreq driver (Ilia
Lin).
- Fix two recent regressions and some other minor issues in the
turbostat utility and extend it to provide some more diagnostic
information (Len Brown, Nathan Ciobanu)"
* tag 'pm-4.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Documentation: intel_pstate: Fix typo
tools/power turbostat: version 18.06.20
tools/power turbostat: add the missing command line switches
tools/power turbostat: add single character tokens to help
tools/power turbostat: alphabetize the help output
tools/power turbostat: fix segfault on 'no node' machines
tools/power turbostat: add optional APIC X2APIC columns
tools/power turbostat: decode cpuid.1.HT
tools/power turbostat: fix show/hide issues resulting from mis-merge
PM / OPP: Update voltage in case freq == old_freq
cpufreq: intel_pstate: Fix scaling max/min limits with Turbo 3.0
cpufreq: kryo: Add module remove and exit
cpufreq: kryo: Fix possible error code dereference
PM / core: Fix supplier device runtime PM usage counter imbalance
L1TF core kernel workarounds are cheap and normally always enabled, However
they still should be reported in sysfs if the system is vulnerable or
mitigated. Add the necessary CPU feature/bug bits.
- Extend the existing checks for Meltdowns to determine if the system is
vulnerable. All CPUs which are not vulnerable to Meltdown are also not
vulnerable to L1TF
- Check for 32bit non PAE and emit a warning as there is no practical way
for mitigation due to the limited physical address bits
- If the system has more than MAX_PA/2 physical memory the invert page
workarounds don't protect the system against the L1TF attack anymore,
because an inverted physical address will also point to valid
memory. Print a warning in this case and report that the system is
vulnerable.
Add a function which returns the PFN limit for the L1TF mitigation, which
will be used in follow up patches for sanity and range checks.
[ tglx: Renamed the CPU feature bit to L1TF_PTEINV ]
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Dave Hansen <dave.hansen@intel.com>
If a device link is added via device_link_add() by the driver of the
link's consumer device, the supplier's runtime PM usage counter is
going to be dropped by the pm_runtime_put_suppliers() call in
driver_probe_device(). However, in that case it is not incremented
unless the supplier driver is already present and the link is not
stateless. That leads to a runtime PM usage counter imbalance for
the supplier device in a few cases.
To prevent that from happening, bump up the supplier runtime
PM usage counter in device_link_add() for all links with the
DL_FLAG_PM_RUNTIME flag set that are added at the consumer probe
time. Use pm_runtime_get_noresume() for that as the callers of
device_link_add() who want the supplier to be resumed by it are
expected to pass DL_FLAG_RPM_ACTIVE in flags to it anyway, but
additionally resume the supplier if the link is added during
consumer driver probe to retain the existing behavior for the
callers depending on it.
Fixes: 21d5c57b37 (PM / runtime: Use device links)
Reported-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: 4.10+ <stable@vger.kernel.org> # 4.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently the code is split over various files with dma- prefixes in the
lib/ and drives/base directories, and the number of files keeps growing.
Move them into a single directory to keep the code together and remove
the file name prefixes. To match the irq infrastructure this directory
is placed under the kernel/ directory.
Signed-off-by: Christoph Hellwig <hch@lst.de>
- Revert a recent PM core change that attempted to fix an issue
related to device links, but introduced a regression (Rafael
Wysocki).
- Fix build when the recently added cpufreq driver for Kryo
processors is selected by making it possible to build that
driver as a module (Arnd Bergmann).
- Fix the long idle detection mechanism in the out-of-band
(ondemand and conservative) cpufreq governors (Chen Yu).
- Add support for devices in multiple power domains to the
generic power domains (genpd) framework (Ulf Hansson).
- Add support for iowait boosting on systems with hardware-managed
P-states (HWP) enabled to the intel_pstate driver and make it use
that feature on systems with Skylake Xeon processors as it is
reported to improve performance significantly on those systems
(Srinivas Pandruvada).
- Fix and update the acpi_cpufreq, ti-cpufreq and imx6q cpufreq
drivers (Colin Ian King, Suman Anna, Sébastien Szymanski).
- Change the behavior of the wakeup_count device attribute in
sysfs to expose the number of events when the device might have
aborted system suspend in progress (Ravi Chandra Sadineni).
- Fix two minor issues in the cpupower utility (Abhishek Goel,
Colin Ian King).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=VROk
-----END PGP SIGNATURE-----
Merge tag 'pm-4.18-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"These revert a recent PM core change that introduced a regression, fix
the build when the recently added Kryo cpufreq driver is selected, add
support for devices attached to multiple power domains to the generic
power domains (genpd) framework, add support for iowait boosting on
systens with hardware-managed P-states (HWP) enabled to the
intel_pstate driver, modify the behavior of the wakeup_count device
attribute in sysfs, fix a few issues and clean up some ugliness,
mostly in cpufreq (core and drivers) and in the cpupower utility.
Specifics:
- Revert a recent PM core change that attempted to fix an issue
related to device links, but introduced a regression (Rafael
Wysocki)
- Fix build when the recently added cpufreq driver for Kryo
processors is selected by making it possible to build that driver
as a module (Arnd Bergmann)
- Fix the long idle detection mechanism in the out-of-band (ondemand
and conservative) cpufreq governors (Chen Yu)
- Add support for devices in multiple power domains to the generic
power domains (genpd) framework (Ulf Hansson)
- Add support for iowait boosting on systems with hardware-managed
P-states (HWP) enabled to the intel_pstate driver and make it use
that feature on systems with Skylake Xeon processors as it is
reported to improve performance significantly on those systems
(Srinivas Pandruvada)
- Fix and update the acpi_cpufreq, ti-cpufreq and imx6q cpufreq
drivers (Colin Ian King, Suman Anna, Sébastien Szymanski)
- Change the behavior of the wakeup_count device attribute in sysfs
to expose the number of events when the device might have aborted
system suspend in progress (Ravi Chandra Sadineni)
- Fix two minor issues in the cpupower utility (Abhishek Goel, Colin
Ian King)"
* tag 'pm-4.18-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "PM / runtime: Fixup reference counting of device link suppliers at probe"
cpufreq: imx6q: check speed grades for i.MX6ULL
cpufreq: governors: Fix long idle detection logic in load calculation
cpufreq: intel_pstate: enable boost for Skylake Xeon
PM / wakeup: Export wakeup_count instead of event_count via sysfs
PM / Domains: Add dev_pm_domain_attach_by_id() to manage multi PM domains
PM / Domains: Add support for multi PM domains per device to genpd
PM / Domains: Split genpd_dev_pm_attach()
PM / Domains: Don't attach devices in genpd with multi PM domains
PM / Domains: dt: Allow power-domain property to be a list of specifiers
cpufreq: intel_pstate: New sysfs entry to control HWP boost
cpufreq: intel_pstate: HWP boost performance on IO wakeup
cpufreq: intel_pstate: Add HWP boost utility and sched util hooks
cpufreq: ti-cpufreq: Use devres managed API in probe()
cpufreq: ti-cpufreq: Fix an incorrect error return value
cpufreq: ACPI: make function acpi_cpufreq_fast_switch() static
cpufreq: kryo: allow building as a loadable module
cpupower : Fix header name to read idle state name
cpupower: fix spelling mistake: "logilename" -> "logfilename"
Additional updates of the generic power domains (genpd) framework
(support for devices attached to multiple domains) and the cpupower
utility (minor fixes) for 4.18-rc1.
* pm-domains:
PM / Domains: Add dev_pm_domain_attach_by_id() to manage multi PM domains
PM / Domains: Add support for multi PM domains per device to genpd
PM / Domains: Split genpd_dev_pm_attach()
PM / Domains: Don't attach devices in genpd with multi PM domains
PM / Domains: dt: Allow power-domain property to be a list of specifiers
* pm-tools:
cpupower : Fix header name to read idle state name
cpupower: fix spelling mistake: "logilename" -> "logfilename"
Revert commit 1e83786198 (PM / runtime: Fixup reference counting of
device link suppliers at probe), as it has introduced a regression
and the condition it was designed to address should be covered by the
existing code.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Spectre v4 mitigation (Speculative Store Bypass Disable) support for
arm64 using SMC firmware call to set a hardware chicken bit
- ACPI PPTT (Processor Properties Topology Table) parsing support and
enable the feature for arm64
- Report signal frame size to user via auxv (AT_MINSIGSTKSZ). The
primary motivation is Scalable Vector Extensions which requires more
space on the signal frame than the currently defined MINSIGSTKSZ
- ARM perf patches: allow building arm-cci as module, demote dev_warn()
to dev_dbg() in arm-ccn event_init(), miscellaneous cleanups
- cmpwait() WFE optimisation to avoid some spurious wakeups
- L1_CACHE_BYTES reverted back to 64 (for performance reasons that have
to do with some network allocations) while keeping ARCH_DMA_MINALIGN
to 128. cache_line_size() returns the actual hardware Cache Writeback
Granule
- Turn LSE atomics on by default in Kconfig
- Kernel fault reporting tidying
- Some #include and miscellaneous cleanups
-----BEGIN PGP SIGNATURE-----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=uums
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
"Apart from the core arm64 and perf changes, the Spectre v4 mitigation
touches the arm KVM code and the ACPI PPTT support touches drivers/
(acpi and cacheinfo). I should have the maintainers' acks in place.
Summary:
- Spectre v4 mitigation (Speculative Store Bypass Disable) support
for arm64 using SMC firmware call to set a hardware chicken bit
- ACPI PPTT (Processor Properties Topology Table) parsing support and
enable the feature for arm64
- Report signal frame size to user via auxv (AT_MINSIGSTKSZ). The
primary motivation is Scalable Vector Extensions which requires
more space on the signal frame than the currently defined
MINSIGSTKSZ
- ARM perf patches: allow building arm-cci as module, demote
dev_warn() to dev_dbg() in arm-ccn event_init(), miscellaneous
cleanups
- cmpwait() WFE optimisation to avoid some spurious wakeups
- L1_CACHE_BYTES reverted back to 64 (for performance reasons that
have to do with some network allocations) while keeping
ARCH_DMA_MINALIGN to 128. cache_line_size() returns the actual
hardware Cache Writeback Granule
- Turn LSE atomics on by default in Kconfig
- Kernel fault reporting tidying
- Some #include and miscellaneous cleanups"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (53 commits)
arm64: Fix syscall restarting around signal suppressed by tracer
arm64: topology: Avoid checking numa mask for scheduler MC selection
ACPI / PPTT: fix build when CONFIG_ACPI_PPTT is not enabled
arm64: cpu_errata: include required headers
arm64: KVM: Move VCPU_WORKAROUND_2_FLAG macros to the top of the file
arm64: signal: Report signal frame size to userspace via auxv
arm64/sve: Thin out initialisation sanity-checks for sve_max_vl
arm64: KVM: Add ARCH_WORKAROUND_2 discovery through ARCH_FEATURES_FUNC_ID
arm64: KVM: Handle guest's ARCH_WORKAROUND_2 requests
arm64: KVM: Add ARCH_WORKAROUND_2 support for guests
arm64: KVM: Add HYP per-cpu accessors
arm64: ssbd: Add prctl interface for per-thread mitigation
arm64: ssbd: Introduce thread flag to control userspace mitigation
arm64: ssbd: Restore mitigation status on CPU resume
arm64: ssbd: Skip apply_ssbd if not using dynamic mitigation
arm64: ssbd: Add global mitigation state accessor
arm64: Add 'ssbd' command-line option
arm64: Add ARCH_WORKAROUND_2 probing
arm64: Add per-cpu infrastructure to call ARCH_WORKAROUND_2
arm64: Call ARCH_WORKAROUND_2 on transitions between EL0 and EL1
...
- Use overflow helpers in 2-factor allocators (Kees, Rasmus)
- Introduce overflow test module (Rasmus, Kees)
- Introduce saturating size helper functions (Matthew, Kees)
- Treewide use of struct_size() for allocators (Kees)
-----BEGIN PGP SIGNATURE-----
Comment: Kees Cook <kees@outflux.net>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=/3L8
-----END PGP SIGNATURE-----
Merge tag 'overflow-v4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull overflow updates from Kees Cook:
"This adds the new overflow checking helpers and adds them to the
2-factor argument allocators. And this adds the saturating size
helpers and does a treewide replacement for the struct_size() usage.
Additionally this adds the overflow testing modules to make sure
everything works.
I'm still working on the treewide replacements for allocators with
"simple" multiplied arguments:
*alloc(a * b, ...) -> *alloc_array(a, b, ...)
and
*zalloc(a * b, ...) -> *calloc(a, b, ...)
as well as the more complex cases, but that's separable from this
portion of the series. I expect to have the rest sent before -rc1
closes; there are a lot of messy cases to clean up.
Summary:
- Introduce arithmetic overflow test helper functions (Rasmus)
- Use overflow helpers in 2-factor allocators (Kees, Rasmus)
- Introduce overflow test module (Rasmus, Kees)
- Introduce saturating size helper functions (Matthew, Kees)
- Treewide use of struct_size() for allocators (Kees)"
* tag 'overflow-v4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
treewide: Use struct_size() for devm_kmalloc() and friends
treewide: Use struct_size() for vmalloc()-family
treewide: Use struct_size() for kmalloc()-family
device: Use overflow helpers for devm_kmalloc()
mm: Use overflow helpers in kvmalloc()
mm: Use overflow helpers in kmalloc_array*()
test_overflow: Add memory allocation overflow tests
overflow.h: Add allocation size calculation helpers
test_overflow: Report test failures
test_overflow: macrofy some more, do more tests for free
lib: add runtime test of check_*_overflow functions
compiler.h: enable builtin overflow checkers and add fallback code
Currently we export event_count instead of wakeup_count via the
per-device wakeup_count sysfs attribute. Change it to wakeup_count
to make it more meaningful.
wakeup_count increments only when events_check_enabled is set,
that is whenever writes the current wakeup count to
/sys/power/wakeup_count. Also events_check_enabled is cleared on
every resume. User space is expected to write to this just before
suspend. This way pm_wakeup_event(), when called from IRQs handles,
will increment wakeup_count only if we are in system-wide
suspend-resume cycle and should give a fair approximation of how many
times a device may have triggered a wakeup from system suspend.
event_count on the other hand will increment every time
pm_wakeup_event() is called irrespective of whether we are in a
suspend-resume cycle and some drivers call it on every interrupt
which makes it less useful for system wakeup tracking.
Signed-off-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
[ rjw: Subject & changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The existing dev_pm_domain_attach() function, allows a single PM domain to
be attached per device. To be able to support devices that are partitioned
across multiple PM domains, let's introduce a new interface,
dev_pm_domain_attach_by_id().
The dev_pm_domain_attach_by_id() returns a new allocated struct device with
the corresponding attached PM domain. This enables for example a driver to
operate on the new device from a power management point of view. The driver
may then also benefit from using the received device, to set up so called
device-links towards its original device. Depending on the situation, these
links may then be dynamically changed.
The new interface is typically called by drivers during their probe phase,
in case they manages devices which uses multiple PM domains. If that is the
case, the driver also becomes responsible of managing the detaching of the
PM domains, which typically should be done at the remove phase. Detaching
is done by calling the existing dev_pm_domain_detach() function and for
each of the received devices from dev_pm_domain_attach_by_id().
Note, currently its only genpd that supports multiple PM domains per
device, but dev_pm_domain_attach_by_id() can easily by extended to cover
other PM domain types, if/when needed.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To support devices being partitioned across multiple PM domains, let's
begin with extending genpd to cope with these kind of configurations.
Therefore, add a new exported function genpd_dev_pm_attach_by_id(), which
is similar to the existing genpd_dev_pm_attach(), but with the difference
that it allows its callers to provide an index to the PM domain that it
wants to attach.
Note that, genpd_dev_pm_attach_by_id() shall only be called by the driver
core / PM core, similar to how the existing dev_pm_domain_attach() makes
use of genpd_dev_pm_attach(). However, this is implemented by following
changes on top.
Because, only one PM domain can be attached per device, genpd needs to
create a virtual device that it can attach/detach instead. More precisely,
let the new function genpd_dev_pm_attach_by_id() register a virtual struct
device via calling device_register(). Then let it attach this device to the
corresponding PM domain, rather than the one that is provided by the
caller. The actual attaching is done via re-using the existing genpd OF
functions.
At successful attachment, genpd_dev_pm_attach_by_id() returns the created
virtual device, which allows the caller to operate on it to deal with power
management. Following changes on top, provides more details in this
regards.
To deal with detaching of a PM domain for the multiple PM domains case,
let's also extend the existing genpd_dev_pm_detach() function, to cover the
cleanup of the created virtual device, via make it call device_unregister()
on it. In this way, there is no need to introduce a new function to deal
with detach for the multiple PM domain case, but instead the existing one
is re-used.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To extend genpd to deal with allowing multiple PM domains per device, some
of the code in genpd_dev_pm_attach() can be re-used. Let's prepare for this
by moving some of the code into a sub-function.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The power-domain DT property may now contain a list of PM domain
specifiers, which represents that a device are partitioned across multiple
PM domains. This leads to a new situation in genpd_dev_pm_attach(), as only
one PM domain can be attached per device.
To remain things simple for the most common configuration, when a single PM
domain is used, let's treat the multiple PM domain case as being specific.
In other words, let's change genpd_dev_pm_attach() to check for multiple PM
domains and prevent it from attach any PM domain for this case. Instead,
leave this to be managed separately, from following changes to genpd.
Suggested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Here is the driver core patchset for 4.18-rc1.
The large chunk of these are firmware core documentation and api
updates. Nothing major there, just better descriptions for others to be
able to understand the firmware code better. There's also a user for a
new firmware api call.
Other than that, there are some minor updates for debugfs, kernfs, and
the driver core itself.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWxbZAg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykbiACgu/2qqou1iV4GxOkvrj5wfsHD+lYAoNPNNDHu
Qf3CCEKbxogF6YowDiAH
=Dsqq
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the driver core patchset for 4.18-rc1.
The large chunk of these are firmware core documentation and api
updates. Nothing major there, just better descriptions for others to
be able to understand the firmware code better. There's also a user
for a new firmware api call.
Other than that, there are some minor updates for debugfs, kernfs, and
the driver core itself.
All of these have been in linux-next for a while with no reported
issues"
* tag 'driver-core-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (23 commits)
driver core: hold dev's parent lock when needed
driver-core: return EINVAL error instead of BUG_ON()
driver core: add __printf verification to device_create_groups_vargs
mm: memory_hotplug: use put_device() if device_register fail
base: core: fix typo 'can by' to 'can be'
debugfs: inode: debugfs_create_dir uses mode permission from parent
debugfs: Re-use kstrtobool_from_user()
Documentation: clarify firmware_class provenance and why we can't rename the module
Documentation: remove stale firmware API reference
Documentation: fix few typos and clarifications for the firmware loader
ath10k: re-enable the firmware fallback mechanism for testmode
ath10k: use firmware_request_nowarn() to load firmware
firmware: add firmware_request_nowarn() - load firmware without warnings
firmware_loader: make firmware_fallback_sysfs() print more useful
firmware_loader: move kconfig FW_LOADER entries to its own file
firmware_loader: replace ---help--- with help
firmware_loader: enhance Kconfig documentation over FW_LOADER
firmware_loader: document firmware_sysfs_fallback()
firmware: rename fw_sysfs_fallback to firmware_fallback_sysfs()
firmware: use () to terminate kernel-doc function names
...
Use the overflow helpers both in existing multiplication-using inlines as
well as the addition-overflow case in the core allocation routine.
Signed-off-by: Kees Cook <keescook@chromium.org>
Modify the device properties framework to remove union aliasing
from it (Andy Shevchenko).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=snbq
-----END PGP SIGNATURE-----
Merge tag 'dp-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull device properties framework update from Rafael Wysocki:
"Modify the device properties framework to remove union aliasing from
it (Andy Shevchenko)"
* tag 'dp-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
device property: Get rid of union aliasing
These include a significant update of the generic power domains (genpd)
and Operating Performance Points (OPP) frameworks, mostly related to
the introduction of power domain performance levels, cpufreq updates
(new driver for Qualcomm Kryo processors, updates of the existing
drivers, some core fixes, schedutil governor improvements), PCI power
management fixes, ACPI workaround for EC-based wakeup events handling
on resume from suspend-to-idle, and major updates of the turbostat
and pm-graph utilities.
Specifics:
- Introduce power domain performance levels into the the generic
power domains (genpd) and Operating Performance Points (OPP)
frameworks (Viresh Kumar, Rajendra Nayak, Dan Carpenter).
- Fix two issues in the runtime PM framework related to the
initialization and removal of devices using device links (Ulf
Hansson).
- Clean up the initialization of drivers for devices in PM domains
(Ulf Hansson, Geert Uytterhoeven).
- Fix a cpufreq core issue related to the policy sysfs interface
causing CPU online to fail for CPUs sharing one cpufreq policy in
some situations (Tao Wang).
- Make it possible to use platform-specific suspend/resume hooks
in the cpufreq-dt driver and make the Armada 37xx DVFS use that
feature (Viresh Kumar, Miquel Raynal).
- Optimize policy transition notifications in cpufreq (Viresh Kumar).
- Improve the iowait boost mechanism in the schedutil cpufreq
governor (Patrick Bellasi).
- Improve the handling of deferred frequency updates in the
schedutil cpufreq governor (Joel Fernandes, Dietmar Eggemann,
Rafael Wysocki, Viresh Kumar).
- Add a new cpufreq driver for Qualcomm Kryo (Ilia Lin).
- Fix and clean up some cpufreq drivers (Colin Ian King, Dmitry
Osipenko, Doug Smythies, Luc Van Oostenryck, Simon Horman,
Viresh Kumar).
- Fix the handling of PCI devices with the DPM_SMART_SUSPEND flag
set and update stale comments in the PCI core PM code (Rafael
Wysocki).
- Work around an issue related to the handling of EC-based wakeup
events in the ACPI PM core during resume from suspend-to-idle if
the EC has been put into the low-power mode (Rafael Wysocki).
- Improve the handling of wakeup source objects in the PM core (Doug
Berger, Mahendran Ganesh, Rafael Wysocki).
- Update the driver core to prevent deferred probe from breaking
suspend/resume ordering (Feng Kan).
- Clean up the PM core somewhat (Bjorn Helgaas, Ulf Hansson, Rafael
Wysocki).
- Make the core suspend/resume code and cpufreq support the RT patch
(Sebastian Andrzej Siewior, Thomas Gleixner).
- Consolidate the PM QoS handling in cpuidle governors (Rafael
Wysocki).
- Fix a possible crash in the hibernation core (Tetsuo Handa).
- Update the rockchip-io Adaptive Voltage Scaling (AVS) driver
(David Wu).
- Update the turbostat utility (fixes, cleanups, new CPU IDs, new
command line options, built-in "Low Power Idle" counters support,
new POLL and POLL% columns) and add an entry for it to MAINTAINERS
(Len Brown, Artem Bityutskiy, Chen Yu, Laura Abbott, Matt Turner,
Prarit Bhargava, Srinivas Pandruvada).
- Update the pm-graph to version 5.1 (Todd Brandt).
- Update the intel_pstate_tracer utility (Doug Smythies).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=wqBV
-----END PGP SIGNATURE-----
Merge tag 'pm-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These include a significant update of the generic power domains
(genpd) and Operating Performance Points (OPP) frameworks, mostly
related to the introduction of power domain performance levels,
cpufreq updates (new driver for Qualcomm Kryo processors, updates of
the existing drivers, some core fixes, schedutil governor
improvements), PCI power management fixes, ACPI workaround for
EC-based wakeup events handling on resume from suspend-to-idle, and
major updates of the turbostat and pm-graph utilities.
Specifics:
- Introduce power domain performance levels into the the generic
power domains (genpd) and Operating Performance Points (OPP)
frameworks (Viresh Kumar, Rajendra Nayak, Dan Carpenter).
- Fix two issues in the runtime PM framework related to the
initialization and removal of devices using device links (Ulf
Hansson).
- Clean up the initialization of drivers for devices in PM domains
(Ulf Hansson, Geert Uytterhoeven).
- Fix a cpufreq core issue related to the policy sysfs interface
causing CPU online to fail for CPUs sharing one cpufreq policy in
some situations (Tao Wang).
- Make it possible to use platform-specific suspend/resume hooks in
the cpufreq-dt driver and make the Armada 37xx DVFS use that
feature (Viresh Kumar, Miquel Raynal).
- Optimize policy transition notifications in cpufreq (Viresh Kumar).
- Improve the iowait boost mechanism in the schedutil cpufreq
governor (Patrick Bellasi).
- Improve the handling of deferred frequency updates in the schedutil
cpufreq governor (Joel Fernandes, Dietmar Eggemann, Rafael Wysocki,
Viresh Kumar).
- Add a new cpufreq driver for Qualcomm Kryo (Ilia Lin).
- Fix and clean up some cpufreq drivers (Colin Ian King, Dmitry
Osipenko, Doug Smythies, Luc Van Oostenryck, Simon Horman, Viresh
Kumar).
- Fix the handling of PCI devices with the DPM_SMART_SUSPEND flag set
and update stale comments in the PCI core PM code (Rafael Wysocki).
- Work around an issue related to the handling of EC-based wakeup
events in the ACPI PM core during resume from suspend-to-idle if
the EC has been put into the low-power mode (Rafael Wysocki).
- Improve the handling of wakeup source objects in the PM core (Doug
Berger, Mahendran Ganesh, Rafael Wysocki).
- Update the driver core to prevent deferred probe from breaking
suspend/resume ordering (Feng Kan).
- Clean up the PM core somewhat (Bjorn Helgaas, Ulf Hansson, Rafael
Wysocki).
- Make the core suspend/resume code and cpufreq support the RT patch
(Sebastian Andrzej Siewior, Thomas Gleixner).
- Consolidate the PM QoS handling in cpuidle governors (Rafael
Wysocki).
- Fix a possible crash in the hibernation core (Tetsuo Handa).
- Update the rockchip-io Adaptive Voltage Scaling (AVS) driver (David
Wu).
- Update the turbostat utility (fixes, cleanups, new CPU IDs, new
command line options, built-in "Low Power Idle" counters support,
new POLL and POLL% columns) and add an entry for it to MAINTAINERS
(Len Brown, Artem Bityutskiy, Chen Yu, Laura Abbott, Matt Turner,
Prarit Bhargava, Srinivas Pandruvada).
- Update the pm-graph to version 5.1 (Todd Brandt).
- Update the intel_pstate_tracer utility (Doug Smythies)"
* tag 'pm-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (128 commits)
tools/power turbostat: update version number
tools/power turbostat: Add Node in output
tools/power turbostat: add node information into turbostat calculations
tools/power turbostat: remove num_ from cpu_topology struct
tools/power turbostat: rename num_cores_per_pkg to num_cores_per_node
tools/power turbostat: track thread ID in cpu_topology
tools/power turbostat: Calculate additional node information for a package
tools/power turbostat: Fix node and siblings lookup data
tools/power turbostat: set max_num_cpus equal to the cpumask length
tools/power turbostat: if --num_iterations, print for specific number of iterations
tools/power turbostat: Add Cannon Lake support
tools/power turbostat: delete duplicate #defines
x86: msr-index.h: Correct SNB_C1/C3_AUTO_UNDEMOTE defines
tools/power turbostat: Correct SNB_C1/C3_AUTO_UNDEMOTE defines
tools/power turbostat: add POLL and POLL% column
tools/power turbostat: Fix --hide Pk%pc10
tools/power turbostat: Build-in "Low Power Idle" counters support
tools/power turbostat: Don't make man pages executable
tools/power turbostat: remove blank lines
tools/power turbostat: a small C-states dump readability immprovement
...
Pull irq updates from Thomas Gleixner:
- Consolidation of softirq pending:
The softirq mask and its accessors/mutators have many implementations
scattered around many architectures. Most do the same things
consisting in a field in a per-cpu struct (often irq_cpustat_t)
accessed through per-cpu ops. We can provide instead a generic
efficient version that most of them can use. In fact s390 is the only
exception because the field is stored in lowcore.
- Support for level!?! triggered MSI (ARM)
Over the past couple of years, we've seen some SoCs coming up with
ways of signalling level interrupts using a new flavor of MSIs, where
the MSI controller uses two distinct messages: one that raises a
virtual line, and one that lowers it. The target MSI controller is in
charge of maintaining the state of the line.
This allows for a much simplified HW signal routing (no need to have
hundreds of discrete lines to signal level interrupts if you already
have a memory bus), but results in a departure from the current idea
the kernel has of MSIs.
- Support for Meson-AXG GPIO irqchip
- Large stm32 irqchip rework (suspend/resume, hierarchical domains)
- More SPDX conversions
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
ARM: dts: stm32: Add exti support to stm32mp157 pinctrl
ARM: dts: stm32: Add exti support for stm32mp157c
pinctrl/stm32: Add irq_eoi for stm32gpio irqchip
irqchip/stm32: Add suspend/resume support for hierarchy domain
irqchip/stm32: Add stm32mp1 support with hierarchy domain
irqchip/stm32: Prepare common functions
irqchip/stm32: Add host and driver data structures
irqchip/stm32: Add suspend support
irqchip/stm32: Add falling pending register support
irqchip/stm32: Checkpatch fix
irqchip/stm32: Optimizes and cleans up stm32-exti irq_domain
irqchip/meson-gpio: Add support for Meson-AXG SoCs
dt-bindings: interrupt-controller: New binding for Meson-AXG SoC
dt-bindings: interrupt-controller: Fix the double quotes
softirq/s390: Move default mutators of overwritten softirq mask to s390
softirq/x86: Switch to generic local_softirq_pending() implementation
softirq/sparc: Switch to generic local_softirq_pending() implementation
softirq/powerpc: Switch to generic local_softirq_pending() implementation
softirq/parisc: Switch to generic local_softirq_pending() implementation
softirq/ia64: Switch to generic local_softirq_pending() implementation
...
This is another quiet release for regmap, there's one minor feature
improvement for the recently added slimbus support and a few minor fixes
and cleanups.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlsVHRITHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0CyMB/4s5liPn80YEm7nVyWyguc10PlE19XJ
OvW88wp4ENv6SvKUyzH3xbsfwaaqBz7vdkofjDEtXawJjCj0Q4YQ3h4Vmn94CstD
51zUoGpUN4xvBlrLcb0EA77OEMhJTrWKrmZgSyA6nOeZtnz1AIOY8qm1k1lE0mVu
Cy7H++GDLKtYBu7fzfxC/txEmexsg9/6aVdUHL5Tt79RvCIVQJHgwsIfTBZZHDrh
o7WK4CN3e9FBz4oJMfPTDdy4KruWz20EYu6PNMV5+Dr2zQZ4hAzElMi4l0dFLSOE
h6a6TexcvXXiD+z5Ie3Ji3PliW35buPFC+W6UHoGI+CL4+aUN/03+zKz
=oz6l
-----END PGP SIGNATURE-----
Merge tag 'regmap-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"This is another quiet release for regmap, there's one minor feature
improvement for the recently added slimbus support and a few minor
fixes and cleanups"
* tag 'regmap-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: slimbus: allow register offsets up to 16 bits
regmap: add missing prototype for devm_init_slimbus
regmap: Skip clk_put for attached clocks when freeing context
regmap: include <linux/ktime.h> from include/linux/regmap.h
- replaceme the force_dma flag with a dma_configure bus method.
(Nipun Gupta, although one patch is іncorrectly attributed to me
due to a git rebase bug)
- use GFP_DMA32 more agressively in dma-direct. (Takashi Iwai)
- remove PCI_DMA_BUS_IS_PHYS and rely on the dma-mapping API to do the
right thing for bounce buffering.
- move dma-debug initialization to common code, and apply a few cleanups
to the dma-debug code.
- cleanup the Kconfig mess around swiotlb selection
- swiotlb comment fixup (Yisheng Xie)
- a trivial swiotlb fix. (Dan Carpenter)
- support swiotlb on RISC-V. (based on a patch from Palmer Dabbelt)
- add a new generic dma-noncoherent dma_map_ops implementation and use
it for arc, c6x and nds32.
- improve scatterlist validity checking in dma-debug. (Robin Murphy)
- add a struct device quirk to limit the dma-mask to 32-bit due to
bridge/system issues, and switch x86 to use it instead of a local
hack for VIA bridges.
- handle devices without a dma_mask more gracefully in the dma-direct
code.
-----BEGIN PGP SIGNATURE-----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=6Acj
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.18' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- replace the force_dma flag with a dma_configure bus method. (Nipun
Gupta, although one patch is іncorrectly attributed to me due to a
git rebase bug)
- use GFP_DMA32 more agressively in dma-direct. (Takashi Iwai)
- remove PCI_DMA_BUS_IS_PHYS and rely on the dma-mapping API to do the
right thing for bounce buffering.
- move dma-debug initialization to common code, and apply a few
cleanups to the dma-debug code.
- cleanup the Kconfig mess around swiotlb selection
- swiotlb comment fixup (Yisheng Xie)
- a trivial swiotlb fix. (Dan Carpenter)
- support swiotlb on RISC-V. (based on a patch from Palmer Dabbelt)
- add a new generic dma-noncoherent dma_map_ops implementation and use
it for arc, c6x and nds32.
- improve scatterlist validity checking in dma-debug. (Robin Murphy)
- add a struct device quirk to limit the dma-mask to 32-bit due to
bridge/system issues, and switch x86 to use it instead of a local
hack for VIA bridges.
- handle devices without a dma_mask more gracefully in the dma-direct
code.
* tag 'dma-mapping-4.18' of git://git.infradead.org/users/hch/dma-mapping: (48 commits)
dma-direct: don't crash on device without dma_mask
nds32: use generic dma_noncoherent_ops
nds32: implement the unmap_sg DMA operation
nds32: consolidate DMA cache maintainance routines
x86/pci-dma: switch the VIA 32-bit DMA quirk to use the struct device flag
x86/pci-dma: remove the explicit nodac and allowdac option
x86/pci-dma: remove the experimental forcesac boot option
Documentation/x86: remove a stray reference to pci-nommu.c
core, dma-direct: add a flag 32-bit dma limits
dma-mapping: remove unused gfp_t parameter to arch_dma_alloc_attrs
dma-debug: check scatterlist segments
c6x: use generic dma_noncoherent_ops
arc: use generic dma_noncoherent_ops
arc: fix arc_dma_{map,unmap}_page
arc: fix arc_dma_sync_sg_for_{cpu,device}
arc: simplify arc_dma_sync_single_for_{cpu,device}
dma-mapping: provide a generic dma-noncoherent implementation
dma-mapping: simplify Kconfig dependencies
riscv: add swiotlb support
riscv: only enable ZONE_DMA32 for 64-bit
...
* pm-pci:
PCI / PM: Clean up outdated comments in pci_target_state()
PCI / PM: Do not clear state_saved for devices that remain suspended
* acpi-pm:
ACPI: EC: Dispatch the EC GPE directly on s2idle wake
ACPICA: Introduce acpi_dispatch_gpe()
* pm-sleep:
PM / hibernate: Fix oops at snapshot_write()
PM / wakeup: Make s2idle_lock a RAW_SPINLOCK
PM / s2idle: Make s2idle_wait_head swait based
PM / wakeup: Make events_lock a RAW_SPINLOCK
PM / suspend: Prevent might sleep splats
* pm-avs:
PM / AVS: rockchip-io: add io selectors and supplies for PX30
* pm-opp: (24 commits)
PM / Domains: Drop unused parameter in genpd_allocate_dev_data()
PM / Domains: Drop genpd as in-param for pm_genpd_remove_device()
PM / Domains: Drop __pm_genpd_add_device()
PM / Domains: Drop extern declarations of functions in pm_domain.h
PM / domains: Add perf_state attribute to genpd debugfs
OPP: Allow same OPP table to be used for multiple genpd
PM / Domain: Return 0 on error from of_genpd_opp_to_performance_state()
PM / OPP: Fix shared OPP table support in dev_pm_opp_register_set_opp_helper()
PM / OPP: Fix shared OPP table support in dev_pm_opp_set_regulators()
PM / OPP: Fix shared OPP table support in dev_pm_opp_set_prop_name()
PM / OPP: Fix shared OPP table support in dev_pm_opp_set_supported_hw()
PM / OPP: silence an uninitialized variable warning
PM / OPP: Remove dev_pm_opp_{un}register_get_pstate_helper()
PM / OPP: Get performance state using genpd helper
PM / Domain: Implement of_genpd_opp_to_performance_state()
PM / Domain: Add support to parse domain's OPP table
PM / Domain: Add struct device to genpd
PM / OPP: Implement dev_pm_opp_get_of_node()
PM / OPP: Implement of_dev_pm_opp_find_required_opp()
PM / OPP: Implement dev_pm_opp_of_add_table_indexed()
...
* pm-domains:
PM / domains: Improve wording of dev_pm_domain_attach() comment
PM / Domains: Don't return -EEXIST at attach when PM domain exists
spi: Respect all error codes from dev_pm_domain_attach()
soundwire: Respect all error codes from dev_pm_domain_attach()
mmc: sdio: Respect all error codes from dev_pm_domain_attach()
i2c: Respect all error codes from dev_pm_domain_attach()
driver core: Respect all error codes from dev_pm_domain_attach()
amba: Respect all error codes from dev_pm_domain_attach()
PM / Domains: Allow a better error handling of dev_pm_domain_attach()
PM / Domains: Check for existing PM domain in dev_pm_domain_attach()
PM / Domains: Drop redundant code in genpd while attaching devices
PM / Domains: Drop comment in genpd about legacy Samsung DT binding
PM / Domains: Fix error path during attach in genpd
* pm-qos:
PM / QoS: Drop redundant declaration of pm_qos_get_value()
* pm-core:
PM / runtime: Drop usage count for suppliers at device link removal
PM / runtime: Fixup reference counting of device link suppliers at probe
PM: wakeup: Use pr_debug() for the "aborting suspend" message
PM / core: Drop unused internal inline functions for sysfs
PM / core: Drop unused internal functions for pm_qos sysfs
PM / core: Drop unused internal inline functions for wakeirqs
PM / core: Drop internal unused inline functions for wakeups
PM / wakeup: Only update last time for active wakeup sources
PM / wakeup: Use seq_open() to show wakeup stats
PM / core: Use dev_printk() and symbols in suspend/resume diagnostics
PM / core: Simplify initcall_debug_report() timing
PM / core: Remove unused initcall_debug_report() arguments
PM / core: fix deferred probe breaking suspend resume order
SoC have internal I/O buses that can't be proved for devices. The
devices on the buses can be accessed directly without additinal
configuration required. This type of bus is represented as
"simple-bus". In some platforms, we name "soc" with "simple-bus"
attribute and many devices are hooked under it described in DT
(device tree).
In commit bf74ad5bc4 ("Hold the device's parent's lock during
probe and remove") to solve USB subsystem lock sequence since
USB device's characteristic. Thus "soc" needs to be locked
whenever a device and driver's probing happen under "soc" bus.
During this period, an async driver tries to probe a device which
is under the "soc" bus would be blocked until previous driver
finish the probing and release "soc" lock. And the next probing
under the "soc" bus need to wait for async finish. Because of
that, driver's async probe for init time improvement will be
shadowed.
Since many devices don't have USB devices' characteristic, they
actually don't need parent's lock. Thus, we introduce a lock flag
in bus_type struct and driver core would lock the parent lock base
on the flag. For USB, we set this flag in usb_bus_type to keep
original lock behavior in driver core.
Async probe could have more benefit after this patch.
Signed-off-by: Martin Liu <liumartin@google.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The in-parameter struct generic_pm_domain *genpd to
genpd_allocate_dev_data() is unused, so let's drop it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is no need to pass a genpd struct to pm_genpd_remove_device(), as we
already have the information about the PM domain (genpd) through the device
structure.
Additionally, we don't allow to remove a PM domain from a device, other
than the one it may have assigned to it, so really it does not make sense
to have a separate in-param for it.
For these reason, drop it and update the current only call to
pm_genpd_remove_device() from amdgpu_acp.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There are still a few non-DT existing users of genpd, however neither of
them uses __pm_genpd_add_device(), hence let's drop it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Now that genpd supports performance states, add this additional
attribute as part of the power domains debugfs entry, to display
the current performance state for the Power domain.
Suggested-by: David Collins <collinsd@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In the case consumer device is runtime resumed, while the link to the
supplier is removed, the earlier call to pm_runtime_get_sync() made from
rpm_get_suppliers() does not get properly balanced with a corresponding
call to pm_runtime_put(). This leads to that suppliers remains to be
runtime resumed forever, while they don't need to.
Let's fix the behaviour by calling rpm_put_suppliers() when dropping a
device link. Not that, since rpm_put_suppliers() checks the
link->rpm_active flag, we can correctly avoid to call pm_runtime_put() in
cases when we shouldn't.
Reported-by: Todor Tomov <todor.tomov@linaro.org>
Fixes: 21d5c57b37 (PM / runtime: Use device links)
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In the driver core, before it invokes really_probe() it runtime resumes the
suppliers for the device via calling pm_runtime_get_suppliers(), which also
increases the runtime PM usage count for each of the available supplier.
This makes sense, as to be able to allow the consumer device to be probed
by its driver. However, if the driver decides to add a new supplier link
during ->probe(), hence updating the list of suppliers, the following call
to pm_runtime_put_suppliers(), invoked after really_probe() in the driver
core, we get into trouble.
More precisely, pm_runtime_put() gets called also for the new supplier(s),
which is wrong as the driver core, didn't trigger pm_runtime_get_sync() to
be called for it in the first place. In other words, the new supplier may
be runtime suspended even in cases when it shouldn't.
Fix this behaviour, by runtime resume suppliers according to the same
conditions as managed by the runtime PM core, when runtime resume callbacks
are being invoked.
Additionally, don't try to runtime suspend any of the suppliers after
really_probe(), but instead rely on that to happen via the consumer device,
when it becomes runtime suspended.
Fixes: 21d5c57b37 (PM / runtime: Use device links)
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The `events_lock' is acquired during suspend while interrupts are
disabled even on RT. The lock is taken only for a very brief moment.
Make it a RAW lock which avoids "sleeping while atomic" warnings on RT.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The case of a new numa node got missed in avoiding using the node info
from page_struct during hotplug. In this path we have a call to
register_mem_sect_under_node (which allows us to specify it is hotplug
so don't change the node), via link_mem_sections which unfortunately
does not.
Fix is to pass check_nid through link_mem_sections as well and disable
it in the new numa node path.
Note the bug only 'sometimes' manifests depending on what happens to be
in the struct page structures - there are lots of them and it only needs
to match one of them.
The result of the bug is that (with a new memory only node) we never
successfully call register_mem_sect_under_node so don't get the memory
associated with the node in sysfs and meminfo for the node doesn't
report it.
It came up whilst testing some arm64 hotplug patches, but appears to be
universal. Whilst I'm triggering it by removing then reinserting memory
to a node with no other elements (thus making the node disappear then
appear again), it appears it would happen on hotplugging memory where
there was none before and it doesn't seem to be related the arm64
patches.
These patches call __add_pages (where most of the issue was fixed by
Pavel's patch). If there is a node at the time of the __add_pages call
then all is well as it calls register_mem_sect_under_node from there
with check_nid set to false. Without a node that function returns
having not done the sysfs related stuff as there is no node to use.
This is expected but it is the resulting path that fails...
Exact path to the problem is as follows:
mm/memory_hotplug.c: add_memory_resource()
The node is not online so we enter the 'if (new_node)' twice, on the
second such block there is a call to link_mem_sections which calls
into
drivers/node.c: link_mem_sections() which calls
drivers/node.c: register_mem_sect_under_node() which calls
get_nid_for_pfn and keeps trying until the output of that matches
the expected node (passed all the way down from
add_memory_resource)
It is effectively the same fix as the one referred to in the fixes tag
just in the code path for a new node where the comments point out we
have to rerun the link creation because it will have failed in
register_new_memory (as there was no node at the time). (actually that
comment is wrong now as we don't have register_new_memory any more it
got renamed to hotplug_memory_register in Pavel's patch).
Link: http://lkml.kernel.org/r/20180504085311.1240-1-Jonathan.Cameron@huawei.com
Fixes: fc44f7f923 ("mm/memory_hotplug: don't read nid from struct page during hotplug")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Pavel Tatashin <pasha.tatashin@oracle.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As per SLIMBus specs Value Elements and Information Elements
address map ranges from 0x000 - 0xFFF.
So allow register addresses up to 16 bits
Fixes: 7d6f7fb053 ("regmap: add SLIMbus support")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
I triggerd the BUG_ON() in driver_register() when booting a domU Xen
domain. Since there was no contextual information logged, I needed to
attach kgdb to determine the culprit (the wmi-bmof driver in my
case). The BUG_ON() was added in commit f48f3febb2 ("driver-core: do
not register a driver with bus_type not registered").
Instead of running into a BUG_ON() we print an error message
identifying the, likely faulty, driver but continue booting.
Signed-off-by: Florian Schmaus <flo@geekplace.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_genpd_opp_to_performance_state() should return 0 on errors, as its
doc comment describes. While it follows that mostly, it returns a
negative error number on one of the failures.
Fix that.
Fixes: 6e41766a6a "PM / Domain: Implement of_genpd_opp_to_performance_state()"
Reported-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix a regression from the 4.15 cycle that caused the system suspend
and resume overhead to increase on many systems and triggered more
serious problems on some of them (Rafael Wysocki).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=BS+S
-----END PGP SIGNATURE-----
Merge tag 'pm-4.17-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Wysocki:
"Fix a regression from the 4.15 cycle that caused the system suspend
and resume overhead to increase on many systems and triggered more
serious problems on some of them (Rafael Wysocki)"
* tag 'pm-4.17-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / core: Fix direct_complete handling for devices with no callbacks
The message printed by pm_wakeup_pending() on wakeup detection is
not very useful if someone is not interested specifically in
debugging wakeup, so turn it into a pm_debug() one.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 08810a4119 (PM / core: Add NEVER_SKIP and SMART_PREPARE
driver flags) inadvertently prevented the power.direct_complete flag
from being set for devices without PM callbacks and with disabled
runtime PM which also prevents power.direct_complete from being set
for their parents. That led to problems including a resume crash on
HP ZBook 14u.
Restore the previous behavior by causing power.direct_complete to be
set for those devices again, but do that in a more direct way to
avoid overlooking that case in the future.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199693
Fixes: 08810a4119 (PM / core: Add NEVER_SKIP and SMART_PREPARE driver flags)
Reported-by: Thomas Martitz <kugel@rockbox.org>
Tested-by: Thomas Martitz <kugel@rockbox.org>
Cc: 4.15+ <stable@vger.kernel.org> # 4.15+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Johan Hovold <johan@kernel.org>
Call ACPI cache parsing routines from base cacheinfo code if ACPI
is enabled. Also stub out cache_setup_acpi and acpi_find_last_cache_level
so that individual architectures can enable ACPI topology parsing.
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Vijaya Kumar K <vkilari@codeaurora.org>
Tested-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Tested-by: Tomasz Nowicki <Tomasz.Nowicki@cavium.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Rename and change the type of of_node to indicate
it is a generic pointer which is generally only used
for comparison purposes. In a later patch we will put
an ACPI/PPTT token pointer in fw_token so that
the code which builds the shared cpu masks can be reused.
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Vijaya Kumar K <vkilari@codeaurora.org>
Tested-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Tested-by: Tomasz Nowicki <Tomasz.Nowicki@cavium.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The original intent in cacheinfo was that an architecture
specific populate_cache_leaves() would probe the hardware
and then cache_shared_cpu_map_setup() and
cache_override_properties() would provide firmware help to
extend/expand upon what was probed. Arm64 was really
the only architecture that was working this way, and
with the removal of most of the hardware probing logic it
became clear that it was possible to simplify the logic a bit.
This patch combines the walk of the DT nodes with the
code updating the cache size/line_size and nr_sets.
cache_override_properties() (which was DT specific) is
then removed. The result is that cacheinfo.of_node is
no longer used as a temporary place to hold DT references
for future calls that update cache properties. That change
helps to clarify its one remaining use (matching
cacheinfo nodes that represent shared caches) which
will be used by the ACPI/PPTT code in the following patches.
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Vijaya Kumar K <vkilari@codeaurora.org>
Tested-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Tested-by: Tomasz Nowicki <Tomasz.Nowicki@cavium.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In preparation for the next patch, and to aid in
review of that patch, lets move cache_setup_of_node
further down in the module without any changes.
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Vijaya Kumar K <vkilari@codeaurora.org>
Tested-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Tested-by: Tomasz Nowicki <Tomasz.Nowicki@cavium.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Commit 318a197182 (device property: refactor built-in properties
support) went way too far and brought a union aliasing. Partially
revert it here to get rid of union aliasing.
Note, all Apple properties are considered as u8 arrays. To get a value
of any of them the caller must use device_property_read_u8_array().
What's union aliasing?
~~~~~~~~~~~~~~~~~~~~~~
The C99 standard in section 6.2.5 paragraph 20 defines union type as
"an overlapping nonempty set of member objects". It also states in
section 6.7.2.1 paragraph 14 that "the value of at most one of the
members can be stored in a union object at any time'.
Union aliasing is a type punning mechanism using union members to store
as one type and read back as another.
Why it's not good?
~~~~~~~~~~~~~~~~~~
Section 6.2.6.1 paragraph 6 says that a union object may not be a trap
representation, although its member objects may be.
Meanwhile annex J.1 says that "the value of a union member other than
the last one stored into" is unspecified [removed in C11].
In TC3, a footnote is added which specifies that accessing a member of a
union other than the last one stored causes "the object representation"
to be re-interpreted in the new type and specifically refers to this as
"type punning". This conflicts to some degree with Annex J.1.
While it's working in Linux with GCC, the use of union members to do
type punning is not clear area in the C standard and might lead to
unspecified behaviour.
More information is available in this [1] blog post.
[1]: https://davmac.wordpress.com/2010/02/26/c99-revisited/
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Capability to attach an existing clk to a MMIO regmap was
introduced in 4.17rc1.
However, when using attached clk, regmap does not do the clk_get.
Therefore it should not do the clk_put when freeing the MMIO
regmap context.
There does not appear to be any users of attached clocks yet
so this would be a good time to make this change before anything
depends on the existing behaviour.
Signed-off-by: James Kelly <jamespeterkelly@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As dev_pm_domain_attach() isn't the only way to assign PM domain pointers
to devices, clearly we must allow a device to have the pointer already
being assigned. For this reason, return 0 instead of -EEXIST.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The limitation of being able to check only for -EPROBE_DEFER from
dev_pm_domain_attach() has been removed. Hence let's respect all error
codes and bail out accordingly.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The callers of dev_pm_domain_attach() currently checks the returned error
code for -EPROBE_DEFER and needs to ignore other error codes. This is an
unnecessary limitation, which also leads to a rather strange behaviour in
the error path.
Address this limitation, by changing the return codes from
acpi_dev_pm_attach() and genpd_dev_pm_attach(). More precisely, let them
return 0, when no PM domain is needed for the device and then return 1, in
case the device was successfully attached to its PM domain. In this way,
dev_pm_domain_attach(), gets a better understanding of what happens in the
attach attempts and also allowing its caller to better act on real errors
codes.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Instead of checking if an existing PM domain pointer has been assigned in
genpd_dev_pm_attach() and acpi_dev_pm_attach(), move the check to the
common path in dev_pm_domain_attach(), thus potentially avoid one
unnecessary check.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The driver core together with the PM core, nowadays deals with deferring
all probes during the device system sleep phases. Therefore genpd no longer
need to care about this situation, so let's drop the corresponding code.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The parsing of the Samsung specific DT binding is gone, but the comment in
the function header remained. Let's drop the comment to avoid confusions.
Fixes: 001d50c9a1 (PM / Domains: Remove obsolete "samsung,power-domain" check)
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In case the PM domain fails to be powered on in genpd_dev_pm_attach(), it
returns -EPROBE_DEFER, but keeping the device attached to its PM domain.
This leads to problems when the next attempt to attach is re-tried. More
precisely, in that situation an -EEXIST error code is returned, because the
device already has its PM domain pointer assigned, from the first attempt.
Now, because of the sloppy error handling by the existing callers of
dev_pm_domain_attach(), probing is allowed to continue when -EEXIST is
returned. However, in such case there are no guarantees that the PM domain
is powered on by genpd, which may lead to hangs when buses/drivers tried to
access their devices.
Let's fix this behaviour, simply by detaching the device when powering on
fails in genpd_dev_pm_attach().
Cc: v4.11+ <stable@vger.kernel.org> # v4.11+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
__printf is useful to verify format and arguments. Remove the following
warning (with W=1):
drivers/base/core.c:2435:2: warning: function might be possible candidate for ‘gnu_printf’ format attribute [-Wsuggest-attribute=format]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
if device_register() returned an error. Always use put_device()
to give up the initialized reference and release allocated memory.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the firmware loader only exposes one silent path for querying
optional firmware, and that is firmware_request_direct(). This function
also disables the sysfs fallback mechanism, which might not always be the
desired behaviour [0].
This patch introduces a variations of request_firmware() that enable the
caller to disable the undesired warning messages but enables the sysfs
fallback mechanism. This is equivalent to adding FW_OPT_NO_WARN to the
old behaviour.
[0]: https://git.kernel.org/linus/c0cc00f250e1
Signed-off-by: Andres Rodriguez <andresx7@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Luis R. Rodriguez <mcgrof@kernel.org>
[mcgrof: used the old API calls as the full rename is not done yet, and
add the caller for when FW_LOADER is disabled, enhance documentation ]
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we resort to using the sysfs fallback mechanism we don't print
the filename. This can be deceiving given we could have a series of
callers intertwined and it'd be unclear exactly for what firmware
this was meant for.
Additionally, although we don't currently use FW_OPT_NO_WARN when
dealing with the fallback mechanism, we will soon, so just respect
its use consistently.
And even if you *don't* want to print always on failure, you may
want to print when debugging so enable dynamic debug print when
FW_OPT_NO_WARN is used.
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This will make it easier to track and easier to understand
what components and features are part of the FW_LOADER. There
are some components related to firmware which have *nothing* to
do with the FW_LOADER, souch as PREVENT_FIRMWARE_BUILD.
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per checkpatch using help is preferred over ---help---.
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If you try to read FW_LOADER today it speaks of old riddles and
unless you have been following development closely you will lose
track of what is what. Even the documentation for PREVENT_FIRMWARE_BUILD
is a bit fuzzy and how it fits into this big picture.
Give the FW_LOADER kconfig documentation some love with more up to
date developments and recommendations. While at it, wrap the FW_LOADER
code into its own menu to compartmentalize and make it clearer which
components really are part of the FW_LOADER. This should also make
it easier to later move these kconfig entries into the firmware_loader/
directory later.
This also now recommends using firmwared [0] for folks left needing a
uevent handler in userspace for the sysfs firmware fallback mechanis
given udev's uevent firmware mechanism was ripped out a while ago.
[0] https://github.com/teg/firmwared
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This also sets the expecations for future fallback interfaces, even
if they are not exported.
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is done since this call is now exposed through kernel-doc,
and since this also paves the way for different future types of
fallback mechanims.
Signed-off-by: Andres Rodriguez <andresx7@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Luis R. Rodriguez <mcgrof@kernel.org>
[mcgrof: small coding style changes]
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel-doc spec dictates a function name ends in ().
Signed-off-by: Andres Rodriguez <andresx7@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Luis R. Rodriguez <mcgrof@kernel.org>
[mcgrof: adjust since the wide API rename is not yet merged]
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This should let us associate enum kdoc to these values.
While at it, kdocify the fw_opt.
Signed-off-by: Andres Rodriguez <andresx7@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Luis R. Rodriguez <mcgrof@kernel.org>
[mcgrof: coding style fixes, merge kdoc with enum move]
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot is hitting WARN() at kernfs_add_one() [1].
This is because kernfs_create_link() is confused by previous device_add()
call which continued without setting dev->kobj.parent field when
get_device_parent() failed by memory allocation fault injection.
Fix this by propagating the error from class_dir_create_and_add() to
the calllers of get_device_parent().
[1] https://syzkaller.appspot.com/bug?id=fae0fb607989ea744526d1c082a5b8de6529116f
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reported-by: syzbot <syzbot+df47f81c226b31d89fb1@syzkaller.appspotmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nobody would be insane enough to try and use level triggered
MSIs on PCI, but let's make sure it doesn't happen. Also,
let's mandate that the irqchip backing the platform MSI domain
is providing the IRQCHIP_SUPPORTS_LEVEL_MSI flag.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Rob Herring <robh@kernel.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lkml.kernel.org/r/20180508121438.11301-3-marc.zyngier@arm.com
The inline versions of rpm_sysfs_remove() and wakeup_sysfs_add|remove(),
are not being used while CONFIG_PM is unset, hence let's drop them.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The functions pm_qos_sysfs_add|remove() are available as inline functions
only while CONFIG_PM is unset, but are not being used. Likely they are a
leftover from an earlier cleanup in the past, anyway let's drop them.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The inline versions of dev_pm_arm|disarm_wake_irq() and
dev_pm_enable|disable_wake_irq_check() are not being used while CONFIG_PM
is unset, hence let's drop them.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The inline versions of device_wakeup_arm|disarm_wake_irqs(), which are
available while when CONFIG_PM is set and CONFIG_PM_SLEEP unset, are not
being used, hence let's drop them.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When wakelock support was added, the wakeup_source_add() function
was updated to set the last_time value of the wakeup source. This
has the unintended side effect of producing confusing output from
pm_print_active_wakeup_sources() when a wakeup source is added
prior to a sleep that is blocked by a different wakeup source.
The function pm_print_active_wakeup_sources() will search for the
most recently active wakeup source when no active source is found.
If a wakeup source is added after a different wakeup source blocks
the system from going to sleep it may have a later last_time value
than the blocking source and be output as the last active wakeup
source even if it has never actually been active.
It looks to me like the change to wakeup_source_add() was made to
prevent the wakelock garbage collection from accidentally dropping
a wakelock during the narrow window between adding the wakelock to
the wakelock list in wakelock_lookup_add() and the activation of
the wakeup source in pm_wake_lock().
This commit changes the behavior so that only the last_time of the
wakeup source used by a wakelock is initialized prior to adding it
to the wakeup source list. This preserves the meaning of the
last_time value as the last time the wakeup source was active and
allows a wakeup source that has never been active to have a
last_time value of 0.
Fixes: b86ff9820f (PM / Sleep: Add user space interface for manipulating wakeup sources, v3)
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
single_open() interface requires that the whole output must
fit into a single buffer. This will lead to timeout when
system memory is not in a good situation.
This patch use seq_open() to show wakeup stats. This method
need only one page, so timeout will not be observed.
Signed-off-by: Ganesh Mahendran <opensource.ganesh@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When we print diagnostic messages about suspend/resume, we have a device
pointer, so use dev_printk() to match other device-related things. Add the
function name, similar to initcall_debug output. E.g.,
- calling 0000:01:00.0+ @ 998, parent: 0000:00:1c.0
+ pci 0000:01:00.0: calling <something> @ 998, parent: 0000:00:1c.0
I wondered if this would break scripts/bootgraph.pl, but I don't think it
will because bootgraph.pl doesn't add any timing information to $start{}
after it sees "Write protecting the" or "Freeing unused kernel memory".
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
initcall_debug_report() always called ktime_get(), even if we didn't
need the result.
Change it so we only call it when we're going to use the result, and
change initcall_debug_start() to follow the same style.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit e8bca479c3 (PM / sleep: trace events for device PM callbacks)
removed the only uses of "state" and "info" from initcall_debug_report().
Remove the now-unused arguments completely.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This implements of_genpd_opp_to_performance_state() which can be used
from the device drivers or the OPP core to find the performance state
encoded in the "required-opps" property of a node. Normally this would
be called only once for each OPP of the device for which the OPP table
of the device is getting generated.
Different platforms may encode the performance state differently using
the OPP table (they may simply return value of opp-hz or opp-microvolt,
or apply some algorithm on top of those values) and so a new callback
->opp_to_performance_state() is implemented to allow platform specific
drivers to convert the power domain OPP to a performance state value.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
The generic power domains can have an OPP table for themselves now, and
phandle of their OPP nodes can be used by the devices powered by the
domain. In order for the OPP core to translate requirements between the
devices and their power domains, both need to have an OPP table in
kernel.
Parse the OPP table for power domains
if they have their
set_performance_state() callback set.
With this patch, an OPP table would be created for the genpd in kernel
based on the OPP table present in DT, if the genpd have its
set_performance_state() callback set.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
The power-domain core would be using the OPP core going forward and the
OPP core has the basic requirement of a device structure for its working.
Add a struct device to the genpd structure. This doesn't register the
device with device core as the "dev" pointer is mostly used by the OPP
core as a cookie for now and registering the device is not mandatory.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
With each bus implementing its own DMA configuration callback, there is no
need for bus to explicitly set the force_dma flag. Modify the
of_dma_configure function to accept an input parameter which specifies if
implicit DMA configuration is required when it is not described by the
firmware.
Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # PCI parts
Reviewed-by: Rob Herring <robh@kernel.org>
[hch: tweaked the changelog a bit]
Signed-off-by: Christoph Hellwig <hch@lst.de>
ACPI/OF support for configuration of DMA is a bus specific aspect, and
thus should be configured by the bus. Introduces a 'dma_configure' bus
method so that busses can control their DMA capabilities.
Also update the PCI, Platform, ACPI and host1x buses to use the new
method.
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # PCI parts
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[hch: simplified host1x_dma_configure based on a comment from Thierry,
rewrote changelog]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add the sysfs file for the new vulerability. It does not do much except
show the words 'Vulnerable' for recent x86 cores.
Intel cores prior to family 6 are known not to be vulnerable, and so are
some Atoms and some Xeon Phi.
It assumes that older Cyrix, Centaur, etc. cores are immune.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Here are some small driver core and firmware fixes for 4.17-rc3
There's a kobject WARN() removal to make syzkaller a lot happier about
some "normal" error paths that it keeps hitting, which should reduce the
number of false-positives we have been getting recently.
There's also some fimware test and documentation fixes, and the
coredump() function signature change that needed to happen after -rc1
before drivers started to take advantage of it.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWuMxrw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymFpQCg1JM62/W8e6mQ4vdZNQmAzgMKMEMAniOMcVRX
/oDWXp64mYwJu+GTxnIJ
=+9Gk
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg Kroah-Hartman:
"Here are some small driver core and firmware fixes for 4.17-rc3
There's a kobject WARN() removal to make syzkaller a lot happier about
some "normal" error paths that it keeps hitting, which should reduce
the number of false-positives we have been getting recently.
There's also some fimware test and documentation fixes, and the
coredump() function signature change that needed to happen after -rc1
before drivers started to take advantage of it.
All of these have been in linux-next with no reported issues"
* tag 'driver-core-4.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
firmware: some documentation fixes
selftests:firmware: fixes a call to a wrong function name
kobject: don't use WARN for registration failures
firmware: Fix firmware documentation for recent file renames
test_firmware: fix setting old custom fw path back on exit, second try
test_firmware: Install all scripts
drivers: change struct device_driver::coredump() return type to void
Including:
- Fixup outdated kernel-doc paths
- Slightly too short title underline
- Some typos
Signed-off-by: Andres Rodriguez <andresx7@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When bridge and its endpoint is enumerated the devices are added to the
dpm list. Afterward, the bridge defers probe when IOMMU is not ready.
This causes the bridge to be moved to the end of the dpm list when
deferred probe kicks in. The order of the dpm list for bridge and
endpoint is reversed.
Add reordering code to move the bridge and its children and consumers to
the end of the pm list so the order for suspend and resume is not altered.
The code also move device and its children and consumers to the tail of
device_kset list if it is registered.
Signed-off-by: Toan Le <toanle@apm.com>
Signed-off-by: Feng Kan <fkan@apm.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Postpone calling virt_to_page() translation on memory locations not
guaranteed to be backed by a struct page. Try first to map memory from
the device coherent memory pool, then perform translation if that fails.
On some architectures, specifically SH when configured with the SPARSEMEM
memory model, assuming a struct page is always assigned to a memory
address lead to unexpected hangs during the virtual to page address
translation. This patch fixes that specific issue but applies in the
general case too.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The use of "correctly mapped" here is misleading, since it can give the
wrong expectation in the case that the memory *should* have been mapped
from the per-device pool, but doing so failed for other reasons.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
__highest_present_section_nr is a more strict boundary than
NR_MEM_SECTIONS. So checking __highest_present_section_nr directly is
enough.
Link: http://lkml.kernel.org/r/20180330032044.21647-1-richard.weiyang@gmail.com
Signed-off-by: Wei Yang <richard.weiyang@gmail.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During memory hotplugging we traverse struct pages three times:
1. memset(0) in sparse_add_one_section()
2. loop in __add_section() to set do: set_page_node(page, nid); and
SetPageReserved(page);
3. loop in memmap_init_zone() to call __init_single_pfn()
This patch removes the first two loops, and leaves only loop 3. All
struct pages are initialized in one place, the same as it is done during
boot.
The benefits:
- We improve memory hotplug performance because we are not evicting the
cache several times and also reduce loop branching overhead.
- Remove condition from hotpath in __init_single_pfn(), that was added
in order to fix the problem that was reported by Bharata in the above
email thread, thus also improve performance during normal boot.
- Make memory hotplug more similar to the boot memory initialization
path because we zero and initialize struct pages only in one
function.
- Simplifies memory hotplug struct page initialization code, and thus
enables future improvements, such as multi-threading the
initialization of struct pages in order to improve hotplug
performance even further on larger machines.
[pasha.tatashin@oracle.com: v5]
Link: http://lkml.kernel.org/r/20180228030308.1116-7-pasha.tatashin@oracle.com
Link: http://lkml.kernel.org/r/20180215165920.8570-7-pasha.tatashin@oracle.com
Signed-off-by: Pavel Tatashin <pasha.tatashin@oracle.com>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Bharata B Rao <bharata@linux.vnet.ibm.com>
Cc: Daniel Jordan <daniel.m.jordan@oracle.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Steven Sistare <steven.sistare@oracle.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During memory hotplugging the probe routine will leave struct pages
uninitialized, the same as it is currently done during boot. Therefore,
we do not want to access the inside of struct pages before
__init_single_page() is called during onlining.
Because during hotplug we know that pages in one memory block belong to
the same numa node, we can skip the checking. We should keep checking
for the boot case.
[pasha.tatashin@oracle.com: s/register_new_memory()/hotplug_memory_register()]
Link: http://lkml.kernel.org/r/20180228030308.1116-6-pasha.tatashin@oracle.com
Link: http://lkml.kernel.org/r/20180215165920.8570-6-pasha.tatashin@oracle.com
Signed-off-by: Pavel Tatashin <pasha.tatashin@oracle.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Baoquan He <bhe@redhat.com>
Cc: Bharata B Rao <bharata@linux.vnet.ibm.com>
Cc: Daniel Jordan <daniel.m.jordan@oracle.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Steven Sistare <steven.sistare@oracle.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When memory is hotplugged pages_correctly_reserved() is called to verify
that the added memory is present, this routine traverses through every
struct page and verifies that PageReserved() is set. This is a slow
operation especially if a large amount of memory is added.
Instead of checking every page, it is enough to simply check that the
section is present, has mapping (struct page array is allocated), and
the mapping is online.
In addition, we should not excpect that probe routine sets flags in
struct page, as the struct pages have not yet been initialized. The
initialization should be done in __init_single_page(), the same as
during boot.
Link: http://lkml.kernel.org/r/20180215165920.8570-5-pasha.tatashin@oracle.com
Signed-off-by: Pavel Tatashin <pasha.tatashin@oracle.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Baoquan He <bhe@redhat.com>
Cc: Bharata B Rao <bharata@linux.vnet.ibm.com>
Cc: Daniel Jordan <daniel.m.jordan@oracle.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Steven Sistare <steven.sistare@oracle.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here is the "big" set of driver core patches for 4.17-rc1.
There's really not much here, just a bunch of firmware code refactoring
from Luis as he attempts to wrangle that codebase into something that is
managable, along with a bunch of userspace tests for it. Other than
that, a handful of small bugfixes and reverts of things that didn't work
out.
Full details are in the shortlog, it's not all that much.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWsSiGg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylPpACgyEKOur8rwp/3uBRxqhoFeWp1RtAAoIvlMjn6
MQ8LIeHNLRnpqGX5L78L
=93HA
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the "big" set of driver core patches for 4.17-rc1.
There's really not much here, just a bunch of firmware code
refactoring from Luis as he attempts to wrangle that codebase into
something that is managable, along with a bunch of userspace tests for
it. Other than that, a handful of small bugfixes and reverts of things
that didn't work out.
Full details are in the shortlog, it's not all that much.
All of these have been in linux-next for a while with no reported
issues"
* tag 'driver-core-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (30 commits)
drivers: base: remove check for callback in coredump_store()
mt7601u: use firmware_request_cache() to address cache on reboot
firmware: add firmware_request_cache() to help with cache on reboot
firmware: fix typo on pr_info_once() when ignore_sysfs_fallback is used
firmware: explicitly include vmalloc.h
firmware: ensure the firmware cache is not used on incompatible calls
test_firmware: modify custom fallback tests to use unique files
firmware: add helper to check to see if fw cache is setup
firmware: fix checking for return values for fw_add_devm_name()
rename: _request_firmware_load() fw_load_sysfs_fallback()
test_firmware: test three firmware kernel configs using a proc knob
test_firmware: expand on library with shared helpers
firmware: enable to force disable the fallback mechanism at run time
firmware: enable run time change of forcing fallback loader
firmware: move firmware loader into its own directory
firmware: split firmware fallback functionality into its own file
firmware: move loading timeout under struct firmware_fallback_config
firmware: use helpers for setting up a temporary cache timeout
firmware: simplify CONFIG_FW_LOADER_USER_HELPER_FALLBACK further
drivers: base: add description for .coredump() callback
...
Here is the big set of USB and PHY driver patches for 4.17-rc1.
Lots of USB typeC work happened this round, with code moving from the
staging directory into the "real" part of the kernel, as well as new
infrastructure being added to be able to handle the different types of
"roles" that typeC requires.
There is also the normal huge set of USB gadget controller and driver
updates, along with XHCI changes, and a raft of other tiny fixes all
over the USB tree. And the PHY driver updates are merged in here as
well as they interacted with the USB drivers in some places.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWsSpJw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylGawCdED2xS3HUxOIqfh81d8B1py8ji04AoJXdLAsH
JgwXbdbibZBabYTVi5s5
=LrRH
-----END PGP SIGNATURE-----
Merge tag 'usb-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big set of USB and PHY driver patches for 4.17-rc1.
Lots of USB typeC work happened this round, with code moving from the
staging directory into the "real" part of the kernel, as well as new
infrastructure being added to be able to handle the different types of
"roles" that typeC requires.
There is also the normal huge set of USB gadget controller and driver
updates, along with XHCI changes, and a raft of other tiny fixes all
over the USB tree. And the PHY driver updates are merged in here as
well as they interacted with the USB drivers in some places.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (250 commits)
Revert "USB: serial: ftdi_sio: add Id for Physik Instrumente E-870"
usb: musb: gadget: misplaced out of bounds check
usb: chipidea: imx: Fix ULPI on imx53
usb: chipidea: imx: Cleanup ci_hdrc_imx_platform_flag
usb: chipidea: usbmisc: small clean up
usb: chipidea: usbmisc: evdo can be set e/o reset
usb: chipidea: usbmisc: evdo is only specific to OTG port
USB: serial: ftdi_sio: add Id for Physik Instrumente E-870
usb: dwc3: gadget: never call ->complete() from ->ep_queue()
usb: gadget: udc: core: update usb_ep_queue() documentation
usb: host: Remove the deprecated ATH79 USB host config options
usb: roles: Fix return value check in intel_xhci_usb_probe()
USB: gadget: f_midi: fixing a possible double-free in f_midi
usb: core: Add USB_QUIRK_DELAY_CTRL_MSG to usbcore quirks
usb: core: Copy parameter string correctly and remove superfluous null check
USB: announce bcdDevice as well as idVendor, idProduct.
USB:fix USB3 devices behind USB3 hubs not resuming at hibernate thaw
usb: hub: Reduce warning to notice on power loss
USB: serial: ftdi_sio: add support for Harman FirmwareHubEmulator
USB: serial: cp210x: add ELDAT Easywave RX09 id
...
This is a fairly large set of updates for regmap, mainly bugfixes. The
biggest bit of this is some fixes for the bulk operations code which
had issues in some use cases, Charles Keepax has sorted them out. We
also gained the ability to use debugfs with syscon regmaps and to
specify the clock to be used with MMIO regmaps.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlrCVS8THGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0I8DCACDPubZk2MzaXHIa/jCNAtJty+lEYuK
X7Q/dOqrUxOoLcpMQNH8cHc9UtQ01xrthOkcOIOwVandOf6VHea7NpNzqZIZwCh9
K5kqpHMOs2Gmx39Kg3ng4lNmzDf/XUeheI8qPDyqAKb9fFQjD+F3bOVsiU7a3VOh
oCGk81fdLEb5Xp2qKaIM3viZ7AemEJABRdKrIs/hghNv4DaHV2auIh8FJ9WFzGwK
s+JAP2RIX9N6HR4mmnDUtfavEDQwrDXN3IDxDjxkgo2CT62e5D1wZ9ixUWM+q1RA
74n3Mc5ZoMxAssNiuEOPRLWTbsPpGtJhKcN0QbUdViM8UMKwHSRvpFAS
=CqUP
-----END PGP SIGNATURE-----
Merge tag 'regmap-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"This is a fairly large set of updates for regmap, mainly bugfixes.
The biggest bit of this is some fixes for the bulk operations code
which had issues in some use cases, Charles Keepax has sorted them
out. We also gained the ability to use debugfs with syscon regmaps and
to specify the clock to be used with MMIO regmaps"
* tag 'regmap-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap: (21 commits)
regmap: debugfs: Improve warning message on debugfs_create_dir() failure
regmap: debugfs: Free map->debugfs_name when debugfs_create_dir() failed
regmap: debugfs: Don't leak dummy names
regmap: debugfs: Disambiguate dummy debugfs file name
regmap: mmio: Add function to attach a clock
regmap: Merge redundant handling in regmap_bulk_write
regmap: Tidy up regmap_raw_write chunking code
regmap: Move the handling for max_raw_write into regmap_raw_write
regmap: Remove unnecessary printk for failed allocation
regmap: Format data for raw write in regmap_bulk_write
regmap: use debugfs even when no device
regmap: Allow missing device in regmap_name_read_file()
regmap: Use _regmap_read in regmap_bulk_read
regmap: Tidy up regmap_raw_read chunking code
regmap: Move the handling for max_raw_read into regmap_raw_read
regmap: Use helper function for register offset
regmap: Don't use format_val in regmap_bulk_read
regmap: Correct comparison in regmap_cached
regmap: Correct offset handling in regmap_volatile_range
regmap-i2c: Off by one in regmap_i2c_smbus_i2c_read/write()
...
- Modify the cpuidle poll state implementation to prevent CPUs from
staying in the loop in there for excessive times (Rafael Wysocki).
- Add Intel Cannon Lake chips support to the RAPL power capping
driver (Joe Konno).
- Add reference counting to the device links handling code in the
PM core (Lukas Wunner).
- Avoid reconfiguring GPEs on suspend-to-idle in the ACPI system
suspend code (Rafael Wysocki).
- Allow devices to be put into deeper low-power states via ACPI
if both _SxD and _SxW are missing (Daniel Drake).
- Reorganize the core ACPI suspend-to-idle wakeup code to avoid a
keyboard wakeup issue on Asus UX331UA (Chris Chiu).
- Prevent the PCMCIA library code from aborting suspend-to-idle due
to noirq suspend failures resulting from incorrect assumptions
(Rafael Wysocki).
- Add coupled cpuidle supprt to the Exynos3250 platform (Marek
Szyprowski).
- Add new sysfs file to make it easier to specify the image storage
location during hibernation (Mario Limonciello).
- Add sysfs files for collecting suspend-to-idle usage and time
statistics for CPU idle states (Rafael Wysocki).
- Update the pm-graph utilities (Todd Brandt).
- Reduce the kernel log noise related to reporting Low-power Idle
constraings by the ACPI system suspend code (Rafael Wysocki).
- Make it easier to distinguish dedicated wakeup IRQs in the
/proc/interrupts output (Tony Lindgren).
- Add the frequency table validation in cpufreq to the core and
drop it from a number of cpufreq drivers (Viresh Kumar).
- Drop "cooling-{min|max}-level" for CPU nodes from a couple of
DT bindings (Viresh Kumar).
- Clean up the CPU online error code path in the cpufreq core
(Viresh Kumar).
- Fix assorted issues in the SCPI, CPPC, mediatek and tegra186
cpufreq drivers (Arnd Bergmann, Chunyu Hu, George Cherian,
Viresh Kumar).
- Drop memory allocation error messages from a few places in
cpufreq and cpuildle drivers (Markus Elfring).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=6JC2
-----END PGP SIGNATURE-----
Merge tag 'pm-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These update the cpuidle poll state definition to reduce excessive
energy usage related to it, add new CPU ID to the RAPL power capping
driver, update the ACPI system suspend code to handle some special
cases better, extend the PM core's device links code slightly, add new
sysfs attribute for better suspend-to-idle diagnostics and easier
hibernation handling, update power management tools and clean up
cpufreq quite a bit.
Specifics:
- Modify the cpuidle poll state implementation to prevent CPUs from
staying in the loop in there for excessive times (Rafael Wysocki).
- Add Intel Cannon Lake chips support to the RAPL power capping
driver (Joe Konno).
- Add reference counting to the device links handling code in the PM
core (Lukas Wunner).
- Avoid reconfiguring GPEs on suspend-to-idle in the ACPI system
suspend code (Rafael Wysocki).
- Allow devices to be put into deeper low-power states via ACPI if
both _SxD and _SxW are missing (Daniel Drake).
- Reorganize the core ACPI suspend-to-idle wakeup code to avoid a
keyboard wakeup issue on Asus UX331UA (Chris Chiu).
- Prevent the PCMCIA library code from aborting suspend-to-idle due
to noirq suspend failures resulting from incorrect assumptions
(Rafael Wysocki).
- Add coupled cpuidle supprt to the Exynos3250 platform (Marek
Szyprowski).
- Add new sysfs file to make it easier to specify the image storage
location during hibernation (Mario Limonciello).
- Add sysfs files for collecting suspend-to-idle usage and time
statistics for CPU idle states (Rafael Wysocki).
- Update the pm-graph utilities (Todd Brandt).
- Reduce the kernel log noise related to reporting Low-power Idle
constraings by the ACPI system suspend code (Rafael Wysocki).
- Make it easier to distinguish dedicated wakeup IRQs in the
/proc/interrupts output (Tony Lindgren).
- Add the frequency table validation in cpufreq to the core and drop
it from a number of cpufreq drivers (Viresh Kumar).
- Drop "cooling-{min|max}-level" for CPU nodes from a couple of DT
bindings (Viresh Kumar).
- Clean up the CPU online error code path in the cpufreq core (Viresh
Kumar).
- Fix assorted issues in the SCPI, CPPC, mediatek and tegra186
cpufreq drivers (Arnd Bergmann, Chunyu Hu, George Cherian, Viresh
Kumar).
- Drop memory allocation error messages from a few places in cpufreq
and cpuildle drivers (Markus Elfring)"
* tag 'pm-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (56 commits)
ACPI / PM: Fix keyboard wakeup from suspend-to-idle on ASUS UX331UA
cpufreq: CPPC: Use transition_delay_us depending transition_latency
PM / hibernate: Change message when writing to /sys/power/resume
PM / hibernate: Make passing hibernate offsets more friendly
cpuidle: poll_state: Avoid invoking local_clock() too often
PM: cpuidle/suspend: Add s2idle usage and time state attributes
cpuidle: Enable coupled cpuidle support on Exynos3250 platform
cpuidle: poll_state: Add time limit to poll_idle()
cpufreq: tegra186: Don't validate the frequency table twice
cpufreq: speedstep: Don't validate the frequency table twice
cpufreq: sparc: Don't validate the frequency table twice
cpufreq: sh: Don't validate the frequency table twice
cpufreq: sfi: Don't validate the frequency table twice
cpufreq: scpi: Don't validate the frequency table twice
cpufreq: sc520: Don't validate the frequency table twice
cpufreq: s3c24xx: Don't validate the frequency table twice
cpufreq: qoirq: Don't validate the frequency table twice
cpufreq: pxa: Don't validate the frequency table twice
cpufreq: ppc_cbe: Don't validate the frequency table twice
cpufreq: powernow: Don't validate the frequency table twice
...
Using this helper allows us to avoid the in-kernel calls to the
sys_unshare() syscall. The ksys_ prefix denotes that this function is meant
as a drop-in replacement for the syscall. In particular, it uses the same
calling convention as sys_unshare().
This patch is part of a series which removes in-kernel calls to syscalls.
On this basis, the syscall entry path can be streamlined. For details, see
http://lkml.kernel.org/r/20180325162527.GA17492@light.dominikbrodowski.net
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Using this helper allows us to avoid the in-kernel calls to the sys_chdir()
syscall. The ksys_ prefix denotes that this function is meant as a drop-in
replacement for the syscall. In particular, it uses the same calling
convention as sys_chdir().
This patch is part of a series which removes in-kernel calls to syscalls.
On this basis, the syscall entry path can be streamlined. For details, see
http://lkml.kernel.org/r/20180325162527.GA17492@light.dominikbrodowski.net
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Using this helper allows us to avoid the in-kernel calls to the
sys_chroot() syscall. The ksys_ prefix denotes that this function is
meant as a drop-in replacement for the syscall. In particular, it uses the
same calling convention as sys_chroot().
In the near future, the fs-external callers of ksys_chroot() should be
converted to use kern_path()/set_fs_root() directly. Then ksys_chroot()
can be moved within sys_chroot() again.
This patch is part of a series which removes in-kernel calls to syscalls.
On this basis, the syscall entry path can be streamlined. For details, see
http://lkml.kernel.org/r/20180325162527.GA17492@light.dominikbrodowski.net
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Using this helper allows us to avoid the in-kernel calls to the sys_mount()
syscall. The ksys_ prefix denotes that this function is meant as a drop-in
replacement for the syscall. In particular, it uses the same calling
convention as sys_mount().
In the near future, all callers of ksys_mount() should be converted to call
do_mount() directly.
This patch is part of a series which removes in-kernel calls to syscalls.
On this basis, the syscall entry path can be streamlined. For details, see
http://lkml.kernel.org/r/20180325162527.GA17492@light.dominikbrodowski.net
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The check for the .coredump() callback in coredump_store() is
redundant. It is already assured the device driver implements
the callback upon creating the coredump sysfs entry.
Signed-off-by: Arend van Spriel <aspriel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some devices have an optimization in place to enable the firmware to
be retaineed during a system reboot, so after reboot the device can skip
requesting and loading the firmware. This can save up to 1s in load
time. The mt7601u 802.11 device happens to be such a device.
When these devices retain the firmware on a reboot and then suspend
they can miss looking for the firmware on resume. To help with this we
need a way to cache the firmware when such an optimization has taken
place.
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the sysctl knob is used ignore the fallback mechanism we pr_info_once()
to ensure its noted the knob was used. The print incorrectly states its a
debugfs knob, its a sysctl knob, so correct this typo.
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several frameworks - clk, gpio, phy, pmw, etc. - maintain
lookup tables for describing connections and provide custom
API for handling them. This introduces a single generic
lookup table and API for the connections.
The motivation for this commit is centralizing the
connection lookup, but the goal is to ultimately extract the
connection descriptions also from firmware by using the
fwnode_graph_* functions and other mechanisms that are
available.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After some other include file changes, fixes:
drivers/base/firmware_loader/fallback.c: In function 'map_fw_priv_pages':
drivers/base/firmware_loader/fallback.c:232:2: error: implicit declaration of function 'vunmap'; did you mean 'kunmap'? [-Werror=implicit-function-declaration]
vunmap(fw_priv->data);
^~~~~~
kunmap
drivers/base/firmware_loader/fallback.c:233:18: error: implicit declaration of function 'vmap'; did you mean 'kmap'? [-Werror=implicit-function-declaration]
fw_priv->data = vmap(fw_priv->pages, fw_priv->nr_pages, 0,
^~~~
kmap
drivers/base/firmware_loader/fallback.c:233:16: warning: assignment makes pointer from integer without a cast [-Wint-conversion]
fw_priv->data = vmap(fw_priv->pages, fw_priv->nr_pages, 0,
^
drivers/base/firmware_loader/fallback.c: In function 'firmware_loading_store':
drivers/base/firmware_loader/fallback.c:274:4: error: implicit declaration of function 'vfree'; did you mean 'kvfree'? [-Werror=implicit-function-declaration]
vfree(fw_priv->pages);
^~~~~
kvfree
drivers/base/firmware_loader/fallback.c: In function 'fw_realloc_pages':
drivers/base/firmware_loader/fallback.c:405:15: error: implicit declaration of function 'vmalloc'; did you mean 'kvmalloc'? [-Werror=implicit-function-declaration]
new_pages = vmalloc(new_array_size * sizeof(void *));
^~~~~~~
kvmalloc
drivers/base/firmware_loader/fallback.c:405:13: warning: assignment makes pointer from integer without a cast [-Wint-conversion]
new_pages = vmalloc(new_array_size * sizeof(void *));
^
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
request_firmware_into_buf() explicitly disables the firmware cache,
meanwhile the firmware cache cannot be used when request_firmware_nowait()
is used without the uevent. Enforce a sanity check for this to avoid future
issues undocumented behaviours should misuses of the firmware cache
happen later.
One of the reasons we want to enforce this is the firmware cache is
used for helping with suspend/resume, and if incompatible calls use it
they can stall suspend.
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a helper to check if the firmware cache is already setup for a device.
This will be used later.
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently fw_add_devm_name() returns 1 if the firmware cache
was already set. This makes it complicated for us to check for
correctness. It is actually non-fatal if the firmware cache
is already setup, so just return 0, and simplify the checkers.
fw_add_devm_name() adds device's name onto the devres for the
device so that prior to suspend we cache the firmware onto memory,
so that on resume the firmware is reliably available. We never
were checking for success for this call though, meaning in some
really rare cases we my have never setup the firmware cache for
a device, which could in turn make resume fail.
This is all theoretical, no known issues have been reported.
This small issue has been present way since the addition of the
devres firmware cache names on v3.7.
Fixes: f531f05ae9 ("firmware loader: store firmware name into devres list")
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reflects much clearer what is being done.
While at it, kdoc'ify it.
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
You currently need four different kernel builds to test the firmware
API fully. By adding a proc knob to force disable the fallback mechanism
completely we are able to reduce the amount of kernels you need built
to test the firmware API down to two.
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently one requires to test four kernel configurations to test the
firmware API completely:
0)
CONFIG_FW_LOADER=y
1)
o CONFIG_FW_LOADER=y
o CONFIG_FW_LOADER_USER_HELPER=y
2)
o CONFIG_FW_LOADER=y
o CONFIG_FW_LOADER_USER_HELPER=y
o CONFIG_FW_LOADER_USER_HELPER_FALLBACK=y
3) When CONFIG_FW_LOADER=m the built-in stuff is disabled, we have
no current tests for this.
We can reduce the requirements to three kernel configurations by making
fw_config.force_sysfs_fallback a proc knob we flip on off. For kernels that
disable CONFIG_IKCONFIG_PROC this can also enable one to inspect if
CONFIG_FW_LOADER_USER_HELPER_FALLBACK was enabled at build time by checking
the proc value at boot time.
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This will make it much easier to manage as we manage to
keep trimming componnents down into their own files to more
easily manage and maintain this codebase.
Suggested-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The firmware fallback code is optional. Split that code out to help
distinguish the fallback functionlity from othere core firmware loader
features. This should make it easier to maintain and review code
changes.
The reason for keeping the configuration onto a table which is built-in
if you enable firmware loading is so that we can later enable the kernel
after subsequent patches to tweak this configuration, even if the
firmware loader is modular.
This introduces no functional changes.
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The timeout is a fallback construct, so we can just stuff the
timeout configuration under struct firmware_fallback_config.
While at it, add a few helpers which vets the use of getting or
setting the timeout as an int. The main use of the timeout is
to set a timeout for completion, and that is used as an unsigned
long. There a few cases however where it makes sense to get or
set the timeout as an int, the helpers annotate these use cases
have been properly vetted for.
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We only use the timeout for the firmware fallback mechanism
except for trying to set the timeout during the cache setup
for resume/suspend. For those cases, setting the timeout should
be a no-op, so just reflect this in code by adding helpers for it.
This change introduces no functional changes.
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All CONFIG_FW_LOADER_USER_HELPER_FALLBACK really is, is just a bool,
initailized at build time. Define it as such. This simplifies the
logic even further, removing now all explicit #ifdefs around the code.
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
if device_register() returned an error! Always use put_device()
to give up the reference initialized.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
if device_register() returned an error! Always use put_device()
to give up the reference initialized.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
if device_register() returned an error! Always use put_device()
to give up the reference initialized.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Never directly free @dev after calling device_register(), even
if it returned an error! Always use put_device() to give up the
reference initialized.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 452562abb5 ("base: arch_topology: fix section
mismatch build warnings"). It causes the notifier call hangs in some
use-cases.
In some cases with using maxcpus, some of cpus are booted first and
then the remaining cpus are booted. As an example, some users who want
to realize fast boot up often use the following procedure.
1) Define all CPUs on device tree (CA57x4 + CA53x4)
2) Add "maxcpus=4" in bootargs
3) Kernel boot up with CA57x4
4) After kernel boot up, CA53x4 is booted from user
When kernel init was finished, CPUFREQ_POLICY_NOTIFIER was not still
unregisterd. This means that "__init init_cpu_capacity_callback()"
will be called after kernel init sequence. To avoid this problem,
it needs to remove __init{,data} annotations by reverting this commit.
Also, this commit was needed to fix kernel compile issue below.
However, this issue was also fixed by another patch: commit 82d8ba717c
("arch_topology: Fix section miss match warning due to
free_raw_capacity()") in v4.15 as well.
Whereas commit 452562abb5 added all the missing __init annotations,
commit 82d8ba717c removed it from free_raw_capacity().
WARNING: vmlinux.o(.text+0x548f24): Section mismatch in reference
from the function init_cpu_capacity_callback() to the variable
.init.text:$x
The function init_cpu_capacity_callback() references
the variable __init $x.
This is often because init_cpu_capacity_callback lacks a __init
annotation or the annotation of $x is wrong.
Fixes: 82d8ba717c ("arch_topology: Fix section miss match warning due to free_raw_capacity()")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Gaku Inami <gaku.inami.xh@renesas.com>
Reviewed-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Tested-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The firmware loader code has grown quite a bit over the years.
The practice of stuffing everything we need into one file makes
the code hard to follow.
In order to split the firmware loader code into different components
we must pick a module name and a first object target file. We must
keep the firmware_class name to remain compatible with scripts which
have been relying on the sysfs loader path for years, so the old module
name stays. We can however rename the C file without affecting the
module name.
The firmware_class used to represent the idea that the code was a simple
sysfs firmware loader, provided by the struct class firmware_class.
The sysfs firmware loader used to be the default, today its only the
fallback mechanism.
This only renames the target code then to make emphasis of what the code
does these days. With this change new features can also use a new object
files.
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently when debugfs_create_dir() fails we receive a warning message
that provides no indication as to what was the directory entry that
failed to be created.
Improve the warning message by printing the directory name that failed
in order to help debugging.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Free map->debugfs_name when debugfs_create_dir() failed to avoid memory
leak.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When allocating dummy names we need to store a pointer to the string we
allocate so that we don't leak it on free.
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit 9b947a13e7 ("regmap: use debugfs even when no device")
allows the usage of regmap debugfs even when there is no device
associated, which causes several warnings like this:
(NULL device *): Failed to create debugfs directory
This happens when the debugfs file name is 'dummy'.
The first dummy debugfs creation works fine, but subsequent creations
fail as they have all the same name.
Disambiguate the 'dummy' debugfs file name by adding a suffix entry,
so that the names become dummy0, dummy1, dummy2, etc.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If device_link_add() is invoked multiple times with the same supplier
and consumer combo, it will create the link on first addition and
return a pointer to the already existing link on all subsequent
additions.
The semantics for device_link_del() are quite different, it deletes
the link unconditionally, so multiple invocations are not allowed.
In other words, this snippet ...
struct device *dev1, *dev2;
struct device_link *link1, *link2;
link1 = device_link_add(dev1, dev2, 0);
link2 = device_link_add(dev1, dev2, 0);
device_link_del(link1);
device_link_del(link2);
... causes the following crash:
WARNING: CPU: 4 PID: 2686 at drivers/base/power/runtime.c:1611 pm_runtime_drop_link+0x40/0x50
[...]
list_del corruption, 0000000039b800a4->prev is LIST_POISON2 (00000000ecf79852)
kernel BUG at lib/list_debug.c:50!
The issue isn't as arbitrary as it may seem: Imagine a device link
which is added in both the supplier's and the consumer's ->probe hook.
The two drivers can't just call device_link_del() in their ->remove hook
without coordination.
Fix by counting multiple additions and dropping the device link only
when the last addition is unwound.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This makes it easy to grep :wakeup /proc/interrupts.
Suggested-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
regmap_init_mmio_clk allows to specify a clock that needs to be enabled
while accessing the registers.
However, that clock is retrieved through its clock ID, which means it will
lookup that clock based on the current device that registers the regmap,
and, in the DT case, will only look in that device OF node.
This might be problematic if the clock to enable is stored in another node.
Let's add a function that allows to attach a clock that has already been
retrieved to a regmap in order to fix this.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The handling for the first two cases in regmap_bulk_write is
essentially identical. The first case is just a better implementation of
the second, supporting 8 byte registers and doing the locking manually to
avoid bouncing the lock for each register. Drop some redundant code by
removing the second of these cases and allowing both situations to be
handled by the same code.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Raw writes may need to be split into small chunks if max_raw_write is
set. Tidy up the code implementing this, the new code is slightly
clearer, slightly shorter and slightly more efficient.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently regmap_bulk_write will split a write into chunks before
calling regmap_raw_write if max_raw_write is set. It is more logical
for this handling to be inside regmap_raw_write itself, as this
removes the need to keep re-implementing the chunking code, which
would be the same for all users of regmap_raw_write.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the case were the bulk transaction is split up into smaller chunks
data is passed directly to regmap_raw_write. However regmap_bulk_write
uses data in host endian and regmap_raw_write expects data in device
endian. As such if the host and device differ in endian the wrong data
will be written to the device. Correct this issue using a similar
approach to the single raw write case below it, duplicate the data
into a new buffer and use parse_inplace to format the data correctly.
Fixes: adaac45975 ("regmap: Introduce max_raw_read/write for regmap_bulk_read/write")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This registers regmaps with debugfs even when they do not have an
associated device. For example, this is common for syscon regmaps.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes a possible NULL pointer dereference oops in
regmap_name_read_file() when the regmap does not have a device
associated with it. For example syscon regmaps retrieved with
syscon_regmap_lookup_by_compatible() don't have a device.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Bulk reads may potentially read a lot of registers and regmap_read will
take and release the regmap lock for each register. Avoid bouncing
the lock so frequently by holding the lock locally and calling
_regmap_read instead. This also has the nice side-effect that all the
reads will be done atomically so no other threads can sneak a write in
during the regmap_bulk_read.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Raw reads may need to be split into small chunks if max_raw_read is
set. Tidy up the code implementing this, the new code is slightly
clearer, slightly shorter and slightly more efficient.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently regmap_bulk_read will split a read into chunks before
calling regmap_raw_read if max_raw_read is set. It is more logical for
this handling to be inside regmap_raw_read itself, as this removes the
need to keep re-implementing the chunking code, which would be the
same for all users of regmap_raw_read.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
- Revert a problematic EC driver change from the 4.13 cycle that
introduced a system resume regression on Thinkpad X240 (Rafael
Wysocki).
- Clean up device tables handling in the ACPI core and the related
part of the device properties framework (Andy Shevchenko).
- Update the sysfs ABI documentatio of the dock and the INT3407
special device drivers (Aishwarya Pant).
- Add an expected switch fall-through marker to the SPCR table
parsing code (Gustavo Silva).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=gdK1
-----END PGP SIGNATURE-----
Merge tag 'acpi-4.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These fix a system resume regression from the 4.13 cycle, clean up
device table handling in the ACPI core, update sysfs ABI documentation
of a couple of drivers and add an expected switch fall-through marker
to the SPCR table parsing code.
Specifics:
- Revert a problematic EC driver change from the 4.13 cycle that
introduced a system resume regression on Thinkpad X240 (Rafael
Wysocki).
- Clean up device tables handling in the ACPI core and the related
part of the device properties framework (Andy Shevchenko).
- Update the sysfs ABI documentatio of the dock and the INT3407
special device drivers (Aishwarya Pant).
- Add an expected switch fall-through marker to the SPCR table
parsing code (Gustavo Silva)"
* tag 'acpi-4.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: dock: document sysfs interface
ACPI / DPTF: Document dptf_power sysfs atttributes
device property: Constify device_get_match_data()
ACPI / bus: Rename acpi_get_match_data() to acpi_device_get_match_data()
ACPI / bus: Remove checks in acpi_get_match_data()
ACPI / bus: Do not traverse through non-existed device table
ACPI: SPCR: Mark expected switch fall-through in acpi_parse_spcr
ACPI / EC: Restore polling during noirq suspend/resume phases
As a helper function exists for calculating register offsets lets use
that rather than open coding with the reg_stride.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A bulk read can be implemented either through regmap_raw_read, or
by reading each register individually using regmap_read. Both
regmap_read and regmap_bulk_read should return values in native
endian. In the individual case the current implementation calls
format_val to put the data into the output array, which can cause
endian issues. The regmap_read will have already converted the data
into native endian, if the hosts endian differs from the device then
format_val will switch the endian back again.
Rather than using format_val simply use the code that is called if
there is no format_val function. This code supports all cases except
24-bit but there don't appear to be any users of regmap_bulk_read for
24-bit. Additionally, it would have to be a big endian host for the
old code to actually function correctly anyway.
Fixes: 15b8d2c41f ("regmap: Fix regmap_bulk_read in BE mode")
Reported-by: David Rhodes <david.rhodes@cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The cache pointer points to the actual memory used by the cache, as the
comparison here is looking for the type of the cache it should check
against cache_type.
Fixes: 1ea975cf1e ("regmap: Add a function to check if a regmap register is cached")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The current implementation is broken for regmaps that have a reg_stride,
since it doesn't take the stride into account. Correct this by using the
helper function to calculate the register offset.
Fixes: f01ee60fff ("regmap: implement register striding")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit baa8809f60 (PM / runtime: Optimize the use of device links)
added an invocation of pm_runtime_drop_link() to __device_link_del().
However there are two variants of that function, one for CONFIG_SRCU and
another for !CONFIG_SRCU, and the commit only modified the former.
Fixes: baa8809f60 (PM / runtime: Optimize the use of device links)
Cc: v4.10+ <stable@vger.kernel.org> # v4.10+
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If a device is runtime PM suspended when we enter suspend and has
a dedicated wake IRQ, we can get the following warning:
WARNING: CPU: 0 PID: 108 at kernel/irq/manage.c:526 enable_irq+0x40/0x94
[ 102.087860] Unbalanced enable for IRQ 147
...
(enable_irq) from [<c06117a8>] (dev_pm_arm_wake_irq+0x4c/0x60)
(dev_pm_arm_wake_irq) from [<c0618360>]
(device_wakeup_arm_wake_irqs+0x58/0x9c)
(device_wakeup_arm_wake_irqs) from [<c0615948>]
(dpm_suspend_noirq+0x10/0x48)
(dpm_suspend_noirq) from [<c01ac7ac>]
(suspend_devices_and_enter+0x30c/0xf14)
(suspend_devices_and_enter) from [<c01adf20>]
(enter_state+0xad4/0xbd8)
(enter_state) from [<c01ad3ec>] (pm_suspend+0x38/0x98)
(pm_suspend) from [<c01ab3e8>] (state_store+0x68/0xc8)
This is because the dedicated wake IRQ for the device may have been
already enabled earlier by dev_pm_enable_wake_irq_check(). Fix the
issue by checking for runtime PM suspended status.
This issue can be easily reproduced by setting serial console log level
to zero, letting the serial console idle, and suspend the system from
an ssh terminal. On resume, dmesg will have the warning above.
The reason why I have not run into this issue earlier has been that I
typically run my PM test cases from on a serial console instead over ssh.
Fixes: c843455975 (PM / wakeirq: Enable dedicated wakeirq for suspend)
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Constify device_get_match_data() as OF and ACPI variants return
constant value.
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Drop the at32ap-cpufreq driver which is useless after the
removal of the corresponding arch (Corentin LABBE).
- Fix a regression from the 4.14 cycle in the APM idle driver by
making it initialize the polling state properly (Rafael Wysocki).
- Fix a crash on failing system suspend due to a missing check in
the cpufreq core (Bo Yan).
- Make the intel_pstate driver initialize the hardware-managed
P-state control (HWP) feature on CPU0 upon resume from system
suspend if HWP had been enabled before the system was suspended
(Chen Yu).
- Fix up the SCPI cpufreq driver after recent changes (Sudeep Holla,
Wei Yongjun).
- Avoid pointer subtractions during frequency table walks in cpufreq
(Dominik Brodowski).
- Avoid the check for ProcFeedback in ST/CZ in the cpufreq driver
for AMD processors and add a MODULE_ALIAS for cpufreq on ARM IMX
(Akshu Agrawal, Nicolas Chauvet).
- Fix the prototype of swsusp_arch_resume() on x86 (Arnd Bergmann).
- Fix up the parsing of power domains DT data (Ulf Hansson).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=xKgy
-----END PGP SIGNATURE-----
Merge tag 'pm-part2-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"These are mostly fixes and cleanups and removal of the no longer
needed at32ap-cpufreq driver.
Specifics:
- Drop the at32ap-cpufreq driver which is useless after the removal
of the corresponding arch (Corentin LABBE).
- Fix a regression from the 4.14 cycle in the APM idle driver by
making it initialize the polling state properly (Rafael Wysocki).
- Fix a crash on failing system suspend due to a missing check in the
cpufreq core (Bo Yan).
- Make the intel_pstate driver initialize the hardware-managed
P-state control (HWP) feature on CPU0 upon resume from system
suspend if HWP had been enabled before the system was suspended
(Chen Yu).
- Fix up the SCPI cpufreq driver after recent changes (Sudeep Holla,
Wei Yongjun).
- Avoid pointer subtractions during frequency table walks in cpufreq
(Dominik Brodowski).
- Avoid the check for ProcFeedback in ST/CZ in the cpufreq driver for
AMD processors and add a MODULE_ALIAS for cpufreq on ARM IMX (Akshu
Agrawal, Nicolas Chauvet).
- Fix the prototype of swsusp_arch_resume() on x86 (Arnd Bergmann).
- Fix up the parsing of power domains DT data (Ulf Hansson)"
* tag 'pm-part2-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
arm: imx: Add MODULE_ALIAS for cpufreq
cpufreq: Add and use cpufreq_for_each_{valid_,}entry_idx()
cpufreq: intel_pstate: Enable HWP during system resume on CPU0
cpufreq: scpi: fix error return code in scpi_cpufreq_init()
x86: hibernate: fix swsusp_arch_resume() prototype
PM / domains: Fix up domain-idle-states OF parsing
cpufreq: scpi: fix static checker warning cdev isn't an ERR_PTR
cpufreq: remove at32ap-cpufreq
cpufreq: AMD: Ignore the check for ProcFeedback in ST/CZ
x86: PM: Make APM idle driver initialize polling state
cpufreq: Skip cpufreq resume if it's not suspended
The commit message says that we are allowed to read and write up to 32
bytes but the code only allows us to write 31 bytes. In other words,
the ">=" should be changed to ">". But this is already checked in
regmap_raw_read()/write() so we can just remove the if statemetents.
Fixes: 29332534e2 ("regmap-i2c: Add smbus i2c block support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We're supposed to be checking that "val_len" is not too large but
instead we check if it is smaller than the max.
The only function affected would be regmap_i2c_smbus_i2c_write() in
drivers/base/regmap/regmap-i2c.c. Strangely that function has its own
limit check which returns an error if (count >= I2C_SMBUS_BLOCK_MAX) so
it doesn't look like it has ever been able to do anything except return
an error.
Fixes: c335931ed9 ("regmap: Add raw_write/read checks for max_raw_write/read sizes")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Commit b539cc82d4 (PM / Domains: Ignore domain-idle-states that are
not compatible), made it possible to ignore non-compatible
domain-idle-states OF nodes. However, in case that happens while doing
the OF parsing, the number of elements in the allocated array would
exceed the numbers actually needed, thus wasting memory.
Fix this by pre-iterating the genpd OF node and counting the number of
compatible domain-idle-states nodes, before doing the allocation. While
doing this, it makes sense to rework the code a bit to avoid open coding,
of parts responsible for the OF node iteration.
Let's also take the opportunity to clarify the function header for
of_genpd_parse_idle_states(), about what is being returned in case of
errors.
Fixes: b539cc82d4 (PM / Domains: Ignore domain-idle-states that are not compatible)
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
