Register STATESTS is 16-bit length, use correct API for read/write.
Signed-off-by: Wang Xingchao <xingchao.wang@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the power state of ALC283 codec goes to D3, it gives a noise via
headphone output. This is because the driver tries to clear all pins
via snd_hda_shutup_pins(). Setting the mic pin to zero triggers such
a noise.
Define a new shutup call specific to this codec and control the pins
there more precisely. Also, add the power-save enable/disable
sequences in the resume and the new shutup calls.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of calling snd_hda_shutup_pins() unconditionally, allow it be
called in spec->shutup callback. In this way, we can avoid calling
this function if it causes a problem like we see in the next patch
following this.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The usage of strict_strto*() is not preferred, because
strict_strto*() is obsolete. Thus, kstrto*() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_hda_jack_detect() function returns a boolean value for a jack
plugged in or not, but it also returns always true when the
corresponding pin is phantom (i.e. fixed). This is OK in most cases,
but it makes the generic parser misbehaving about the auto-mute or
auto-mic switching, e.g. when one of headphone pins is a fixed.
Namely, the driver decides whether to mute the speaker or not, just
depending on the headphone plug state: if one of the headphone jacks
is seen as active, then the speaker is muted. Thus this will result
always in the muted speaker output.
So, the problem is the function returns a boolean, after all, although
we need to think of "phantom" jack. Now a new function,
snd_hda_jack_detect_state() is introduced to return these tristates.
The generic parser uses this function for checking the headphone or
mic jack states.
Meanwhile, the behavior of snd_hda_jack_detect() is kept as is, for
keeping compatibility in other driver codes.
Acked-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This Conexant codec has a single jack that can be used as either
headphone or mic (but not headset). The existing hp_mic functionality
does not apply here, because the mic and the HP are on separate pins.
Hence make a lighter version of what has been earlier done for Realtek
codecs.
BugLink: https://bugs.launchpad.net/bugs/1198030
Tested-by: Franz Hsieh <franz.hsieh@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is our first set of fixes from arm-soc for 3.11.
- A handful of build and warning fixes from Arnd
- A collection of OMAP fixes
- defconfig updates to make the default configs more useful for real use
(and testing) out of the box on hardware.
And a couple of other small fixes. Some of these have been recently
applied but it's normally how we deal with fixes, with less bake time
in -next needed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=fKfy
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"This is our first set of fixes from arm-soc for 3.11.
- A handful of build and warning fixes from Arnd
- A collection of OMAP fixes
- defconfig updates to make the default configs more useful for real
use (and testing) out of the box on hardware
And a couple of other small fixes. Some of these have been recently
applied but it's normally how we deal with fixes, with less bake time
in -next needed"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (32 commits)
arm: multi_v7_defconfig: Tweaks for omap and sunxi
arm: multi_v7_defconfig: add i.MX options and NFS root
ARM: omap2: add select of TI_PRIV_EDMA
ARM: exynos: select PM_GENERIC_DOMAINS only when used
ARM: ixp4xx: avoid circular header dependency
ARM: OMAP: omap_common_late_init may be unused
ARM: sti: move DEBUG_STI_UART into alphabetical order
ARM: OMAP: build mach-omap code only if needed
ARM: zynq: use DT_MACHINE_START
ARM: omap5: omap5 has SCU and TWD
ARM: OMAP2+: omap2plus_defconfig: Enable appended DTB support
ARM: OMAP2+: Enable TI_EDMA in omap2plus_defconfig
ARM: OMAP2+: omap2plus_defconfig: enable DRA752 thermal support by default
ARM: OMAP2+: omap2plus_defconfig: enable TI bandgap driver
ARM: OMAP2+: devices: remove duplicated include from devices.c
ARM: OMAP3: igep0020: Set DSS pins in correct mux mode.
ARM: OMAP2+: N900: enable N900-specific drivers even if device tree is enabled
ARM: OMAP2+: Cocci spatch "ptr_ret.spatch"
ARM: OMAP2+: Remove obsolete Makefile line
ARM: OMAP5: Enable Cortex A15 errata 798181
...
Make struct ieee1394_device_id.driver_data actually avaliable to
1394 protocol drivers. This is especially useful to 1394 audio drivers
for model-specific parameters and methods.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.20 (GNU/Linux)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=8MqX
-----END PGP SIGNATURE-----
Merge tag 'firewire-updates' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
Pull firewire updates from Stefan Richter:
"Make struct ieee1394_device_id.driver_data actually avaliable to 1394
protocol drivers. This is especially useful to 1394 audio drivers for
model-specific parameters and methods"
* tag 'firewire-updates' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: remove support of fw_driver.driver.probe and .remove methods
firewire: introduce fw_driver.probe and .remove methods
Commit 8f898e92ae removed the redundant
reads of bInterfaceProtocol from the descriptors, but introduced a
regression to devices with quirks of type QUIRK_AUDIO_FIXED_ENDPOINT,
since fp->protocol is not set in setup process.
As a consequence, audio streams would not get initialized, as the
following logs show:
[ 48.923043] setting usb interface 3:1
[ 48.923056] Creating new capture data endpoint #81
[ 48.923484] 4:3:1: cannot set freq 48000 to ep 0x81
This patch sets fp->protocol in create_fixed_stream_quirk() and
resolves the regression.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
"pcm" member in struct fwspk is used to set pcm operations but is not used
again. This commit remove this member and set pcm operations with
snd_pcm_set_ops().
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pull drm updates from Dave Airlie:
"Okay this is the big one, I was stalled on the fbdev pull req as I
stupidly let fbdev guys merge a patch I required to fix a warning with
some patches I had, they ended up merging the patch from the wrong
place, but the warning should be fixed. In future I'll just take the
patch myself!
Outside drm:
There are some snd changes for the HDMI audio interactions on haswell,
they've been acked for inclusion via my tree. This relies on the
wound/wait tree from Ingo which is already merged.
Major changes:
AMD finally released the dynamic power management code for all their
GPUs from r600->present day, this is great, off by default for now but
also a huge amount of code, in fact it is most of this pull request.
Since it landed there has been a lot of community testing and Alex has
sent a lot of fixes for any bugs found so far. I suspect radeon might
now be the biggest kernel driver ever :-P p.s. radeon.dpm=1 to enable
dynamic powermanagement for anyone.
New drivers:
Renesas r-car display unit.
Other highlights:
- core: GEM CMA prime support, use new w/w mutexs for TTM
reservations, cursor hotspot, doc updates
- dvo chips: chrontel 7010B support
- i915: Haswell (fbc, ips, vecs, watermarks, audio powerwell),
Valleyview (enabled by default, rc6), lots of pll reworking, 30bpp
support (this time for sure)
- nouveau: async buffer object deletion, context/register init
updates, kernel vp2 engine support, GF117 support, GK110 accel
support (with external nvidia ucode), context cleanups.
- exynos: memory leak fixes, Add S3C64XX SoC series support, device
tree updates, common clock framework support,
- qxl: cursor hotspot support, multi-monitor support, suspend/resume
support
- mgag200: hw cursor support, g200 mode limiting
- shmobile: prime support
- tegra: fixes mostly
I've been banging on this quite a lot due to the size of it, and it
seems to okay on everything I've tested it on."
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (811 commits)
drm/radeon/dpm: implement vblank_too_short callback for si
drm/radeon/dpm: implement vblank_too_short callback for cayman
drm/radeon/dpm: implement vblank_too_short callback for btc
drm/radeon/dpm: implement vblank_too_short callback for evergreen
drm/radeon/dpm: implement vblank_too_short callback for 7xx
drm/radeon/dpm: add checks against vblank time
drm/radeon/dpm: add helper to calculate vblank time
drm/radeon: remove stray line in old pm code
drm/radeon/dpm: fix display_gap programming on rv7xx
drm/nvc0/gr: fix gpc firmware regression
drm/nouveau: fix minor thinko causing bo moves to not be async on kepler
drm/radeon/dpm: implement force performance level for TN
drm/radeon/dpm: implement force performance level for ON/LN
drm/radeon/dpm: implement force performance level for SI
drm/radeon/dpm: implement force performance level for cayman
drm/radeon/dpm: implement force performance levels for 7xx/eg/btc
drm/radeon/dpm: add infrastructure to force performance levels
drm/radeon: fix surface setup on r1xx
drm/radeon: add support for 3d perf states on older asics
drm/radeon: set default clocks for SI when DPM is disabled
...
ALC5505 DSP is enabled even though we don't use the features yet at
all. This results in the unnecessarily high power consumption, more
than 100mV higher. Until we implement the DSP support, better to
bypass DSP for saving more power.
Reported-by: Mengdong Lin <mengdong.lin@intel.com>
[Patch modified by Mengdong to cal alc5505_dsp_init() with extra
acl5505_dsp_halt().]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Also use snd_ctl_enum_info() to fill the autosync text fields on AES32
and MADI cards (only users of snd_hdspm_info_autosync_ref).
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Also use snd_ctl_enum_info() to fill the autosync enumerated controls.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use snd_ctl_enum_info() to fill most of the enumerated controls. More
non-trivial occurrences will follow in separate commits.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch finally enables TCO support on RME AES(32) cards.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds a new ALSA control to read the external sample rate from
userspace on RME AES(32) cards.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch refactors the code to query the external sample rate and its
translation into the corresponding enum into a helper function to
prevent future code duplication.
A later commit will make use of this new helper function.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Also report TCO status and Sync-In via /proc/ on AES(32) cards.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch enables the user to select "TCO" and "Sync In" as a preferred
sync reference on RME AES(32) cards.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds support to read the TCO sample rate in
hdspm_external_sample_rate() on RME AES(32) cards.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As mentioned in the comment, the AES32 cards must not set the format
bit, since it is used to indicate the preferred sync setting instead.
We hence simply skip the corresponding part in the hw_params function.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds AES32 specific code to hdspm_get_tco_sample_rate to
query the TCO sample rate.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds AES32 specific code to hdspm_get_wc_sample_rate() to
query the wordclock frequency.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch only introduces prototype declarations, no real change. The
functions themselves are already present.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Helper function to return the AES sample rate class. This class needs to
be translated via HDSPM_bit2freq() to get the more common
representation.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Provide the text for the two new clock options "TCO" and "Sync In" on
AES32 cards.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HDSPM_AUTOSYNC_REF macro is only implemented for MADI and AES32
cards, so it doesn't make sense to call it on AIO boards.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch does nothing, it's sole intent is to clean up the code.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDSPM_tco_lock and HDSPM_tcoLock were too close, so the previous code
didn't honour the difference between the two.
Let's be more verbose and use HDSPM_tcoLockMadi for MADI cards,
HDSPM_tcoLockAes for AES(32) and fix the code that makes use of both.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch separates the TCO bits from snd_hdspm_proc_read_madi(), so
the new function can later be shared between MADI and AES32 cards.
It's essentially only moving code around, no new functionality.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a left-over mistake from old code, the correct register offset is
provided in kcontrol->private_value, not in the index.
Cf. RayDAT case, where it has already been corrected.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AIO cards allow to use AEB (Analogue Expansion Boards) to add four
input and/or output channels.
This patch adds the necessary code to detect and enable the additional
I/O channels.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch uses the newly introduced HDSPM_CONTROL_TRISTATE functions to
create and expose the following ALSA controls:
- Gain selection for Input, Output and Phones (HiGain, +4dBu, -10dbV)
- S/PDIF Input select (Coaxial, Optical, Internal)
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AIO cards offer at least four individual settings options with three
states each. Those settings are represented as two bits in the settings
register with the following meaning:
0*some_base_bit --> Option value 0
1*some_base_bit --> Option value 1
2*some_base_bit --> Option value 2
3*some_base_bit --> mask to select the two involved bits
This patch adds a generic ALSA control macro for such a value-to-bit
pattern mapping. It will be used in a later commit to expose four new
controls.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ENUMERATED_CTL_INFO is a macro, so the binary code is generated multiple
times. To avoid code duplication, refactor the involved functionality
into a function and make ENUMERATED_CTL_INFO a call to this function.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds the following ALSA controls:
- S/PDIF Out Optical to switch S/PDIF Out from coaxial to optical
- S/PDIF Out Professional to send the Pro bit in the output stream
- ADAT-Internal to enable ADAT/TDIF Expansion Board (AEB/TEB)
- XLR Breakout Cable if analogue I/O uses the XLR breakout cable
- WCK48 to force WordClock to the 32-48kHz range (single speed) if
the card is operating at higher frequencies
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds new ALSA controls to send single-speed WordClock and
S/PDIF-Professional on RME RayDAT cards.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
hdspm_set_system_clock_mode() is almost a one-by-one copy of
hdspm_set_toggle_setting(). To improve code quality, remove the
duplication.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HDSPM_TOGGLE_SETTING functions alter the control_register on older
cards. On newer cards (AIO/RayDAT), they have to operate on the
settings_register instead.
This patch augments the existing functions to work with AIO/RayDAT, too.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
RME RayDAT and AIO cards are new designs with different register
settings. Since we need to distinguish them from older cards multiple
times in the driver, refactor the code into a separate helper function.
No functional change intended.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The driver did not support all possible configurations. These defines
will be used by later commits to add the missing functionality.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Finally all the static quirks in patch_analog.c are reduced by this
patch. As machines with AD1986A codec are all old and often their
BIOS are buggy, we need to keep at least a few static pin conifgs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few small fixes, all driver specific. The removal of the GPIO based
pinmuxing is a bug fix, since the obsolete nodes had been removed from
the DT it stopped the driver loading.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=+rVP
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.11-4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v3.11
A few small fixes, all driver specific. The removal of the GPIO based
pinmuxing is a bug fix, since the obsolete nodes had been removed from
the DT it stopped the driver loading.
Pull trivial tree updates from Jiri Kosina:
"The usual stuff from trivial tree"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
treewide: relase -> release
Documentation/cgroups/memory.txt: fix stat file documentation
sysctl/net.txt: delete reference to obsolete 2.4.x kernel
spinlock_api_smp.h: fix preprocessor comments
treewide: Fix typo in printk
doc: device tree: clarify stuff in usage-model.txt.
open firmware: "/aliasas" -> "/aliases"
md: bcache: Fixed a typo with the word 'arithmetic'
irq/generic-chip: fix a few kernel-doc entries
frv: Convert use of typedef ctl_table to struct ctl_table
sgi: xpc: Convert use of typedef ctl_table to struct ctl_table
doc: clk: Fix incorrect wording
Documentation/arm/IXP4xx fix a typo
Documentation/networking/ieee802154 fix a typo
Documentation/DocBook/media/v4l fix a typo
Documentation/video4linux/si476x.txt fix a typo
Documentation/virtual/kvm/api.txt fix a typo
Documentation/early-userspace/README fix a typo
Documentation/video4linux/soc-camera.txt fix a typo
lguest: fix CONFIG_PAE -> CONFIG_x86_PAE in comment
...
