Add SAI I2S and audio bindings to Data Modul i.MX8M Plus eDM SBC.
The SGTL5000 is attached to SAI3, however the SGTL5000 codec MCLK
must be supplied even if the SAI3 is not in use and is controlled
separately by the codec. The MCLK is also used to drive the codec
I2C block, so without MCLK, I2C access to the codec would not be
possible.
To provide such flexible MCLK control, use PWM4 with period 1 and
duty cycle 50% as 12 MHz clock source, as there is no direct way
to route MX8MP CCM clock to the MCLK pin. Use codec as bitclock
and frame clock master, so that the SGTL5000 PLL can be used to
generate derived clock.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Bindings say DMA channels are in order Rx, Tx. Adjust the DT nodes
accordingly. While at it, use defines for the flags.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Sort nodes by base address. edma3 comes later in the memory map.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
edma0 of iMX8DXL is difference with other imx8 chips. Update register's
size, channel number and power-domain.
Update i2c[0-3] channel number information.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Now that the minimum supported version of LLVM for building the kernel has
been bumped to 13.0.1, several conditions become tautologies, as they will
always be true because the build will fail during the configuration stage
for older LLVM versions. Drop them, as they are unnecessary.
Link: https://lkml.kernel.org/r/20240125-bump-min-llvm-ver-to-13-0-1-v1-5-f5ff9bda41c5@kernel.org
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: "Aneesh Kumar K.V (IBM)" <aneesh.kumar@kernel.org>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Borislav Petkov (AMD) <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Conor Dooley <conor@kernel.org>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Masahiro Yamada <masahiroy@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: "Naveen N. Rao" <naveen.n.rao@linux.ibm.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Nicolas Schier <nicolas@fjasle.eu>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
reviews.llvm.org was LLVM's Phabricator instances for code review. It has
been abandoned in favor of GitHub pull requests. While the majority of
links in the kernel sources still work because of the work Fangrui has
done turning the dynamic Phabricator instance into a static archive, there
are some issues with that work, so preemptively convert all the links in
the kernel sources to point to the commit on GitHub.
Most of the commits have the corresponding differential review link in the
commit message itself so there should not be any loss of fidelity in the
relevant information.
Link: https://discourse.llvm.org/t/update-on-github-pull-requests/71540/172
Link: https://lkml.kernel.org/r/20240109-update-llvm-links-v1-2-eb09b59db071@kernel.org
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Fangrui Song <maskray@google.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Andrii Nakryiko <andrii@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Mykola Lysenko <mykolal@fb.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
There are situations where a change to a single PTE could cause the
contpte block in which it resides to become foldable (i.e. could be
repainted with the contiguous bit). Such situations arise, for example,
when user space temporarily changes protections, via mprotect, for
individual pages, such can be the case for certain garbage collectors.
We would like to detect when such a PTE change occurs. However this can
be expensive due to the amount of checking required. Therefore only
perform the checks when an indiviual PTE is modified via mprotect
(ptep_modify_prot_commit() -> set_pte_at() -> set_ptes(nr=1)) and only
when we are setting the final PTE in a contpte-aligned block.
Link: https://lkml.kernel.org/r/20240215103205.2607016-19-ryan.roberts@arm.com
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Barry Song <21cnbao@gmail.com>
Cc: Borislav Petkov (AMD) <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Morse <james.morse@arm.com>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will@kernel.org>
Cc: Yang Shi <shy828301@gmail.com>
Cc: Zi Yan <ziy@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
As set_ptes() and wrprotect_ptes() become a bit more complex, the compiler
may choose not to inline them. But this is critical for fork()
performance. So mark the functions, along with contpte_try_unfold() which
is called by them, as __always_inline. This is worth ~1% on the fork()
microbenchmark with order-0 folios (the common case).
Link: https://lkml.kernel.org/r/20240215103205.2607016-18-ryan.roberts@arm.com
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Barry Song <21cnbao@gmail.com>
Cc: Borislav Petkov (AMD) <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Morse <james.morse@arm.com>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will@kernel.org>
Cc: Yang Shi <shy828301@gmail.com>
Cc: Zi Yan <ziy@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
When core code iterates over a range of ptes and calls ptep_get() for each
of them, if the range happens to cover contpte mappings, the number of pte
reads becomes amplified by a factor of the number of PTEs in a contpte
block. This is because for each call to ptep_get(), the implementation
must read all of the ptes in the contpte block to which it belongs to
gather the access and dirty bits.
This causes a hotspot for fork(), as well as operations that unmap memory
such as munmap(), exit and madvise(MADV_DONTNEED). Fortunately we can fix
this by implementing pte_batch_hint() which allows their iterators to skip
getting the contpte tail ptes when gathering the batch of ptes to operate
on. This results in the number of PTE reads returning to 1 per pte.
Link: https://lkml.kernel.org/r/20240215103205.2607016-17-ryan.roberts@arm.com
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Tested-by: John Hubbard <jhubbard@nvidia.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Barry Song <21cnbao@gmail.com>
Cc: Borislav Petkov (AMD) <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Morse <james.morse@arm.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will@kernel.org>
Cc: Yang Shi <shy828301@gmail.com>
Cc: Zi Yan <ziy@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Optimize the contpte implementation to fix some of the
exit/munmap/dontneed performance regression introduced by the initial
contpte commit. Subsequent patches will solve it entirely.
During exit(), munmap() or madvise(MADV_DONTNEED), mappings must be
cleared. Previously this was done 1 PTE at a time. But the core-mm
supports batched clear via the new [get_and_]clear_full_ptes() APIs. So
let's implement those APIs and for fully covered contpte mappings, we no
longer need to unfold the contpte. This significantly reduces unfolding
operations, reducing the number of tlbis that must be issued.
Link: https://lkml.kernel.org/r/20240215103205.2607016-15-ryan.roberts@arm.com
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Tested-by: John Hubbard <jhubbard@nvidia.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Barry Song <21cnbao@gmail.com>
Cc: Borislav Petkov (AMD) <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Morse <james.morse@arm.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will@kernel.org>
Cc: Yang Shi <shy828301@gmail.com>
Cc: Zi Yan <ziy@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Optimize the contpte implementation to fix some of the fork performance
regression introduced by the initial contpte commit. Subsequent patches
will solve it entirely.
During fork(), any private memory in the parent must be write-protected.
Previously this was done 1 PTE at a time. But the core-mm supports
batched wrprotect via the new wrprotect_ptes() API. So let's implement
that API and for fully covered contpte mappings, we no longer need to
unfold the contpte. This has 2 benefits:
- reduced unfolding, reduces the number of tlbis that must be issued.
- The memory remains contpte-mapped ("folded") in the parent, so it
continues to benefit from the more efficient use of the TLB after
the fork.
The optimization to wrprotect a whole contpte block without unfolding is
possible thanks to the tightening of the Arm ARM in respect to the
definition and behaviour when 'Misprogramming the Contiguous bit'. See
section D21194 at https://developer.arm.com/documentation/102105/ja-07/
Link: https://lkml.kernel.org/r/20240215103205.2607016-14-ryan.roberts@arm.com
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Tested-by: John Hubbard <jhubbard@nvidia.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Barry Song <21cnbao@gmail.com>
Cc: Borislav Petkov (AMD) <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Morse <james.morse@arm.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will@kernel.org>
Cc: Yang Shi <shy828301@gmail.com>
Cc: Zi Yan <ziy@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
With the ptep API sufficiently refactored, we can now introduce a new
"contpte" API layer, which transparently manages the PTE_CONT bit for user
mappings.
In this initial implementation, only suitable batches of PTEs, set via
set_ptes(), are mapped with the PTE_CONT bit. Any subsequent modification
of individual PTEs will cause an "unfold" operation to repaint the contpte
block as individual PTEs before performing the requested operation.
While, a modification of a single PTE could cause the block of PTEs to
which it belongs to become eligible for "folding" into a contpte entry,
"folding" is not performed in this initial implementation due to the costs
of checking the requirements are met. Due to this, contpte mappings will
degrade back to normal pte mappings over time if/when protections are
changed. This will be solved in a future patch.
Since a contpte block only has a single access and dirty bit, the semantic
here changes slightly; when getting a pte (e.g. ptep_get()) that is part
of a contpte mapping, the access and dirty information are pulled from the
block (so all ptes in the block return the same access/dirty info). When
changing the access/dirty info on a pte (e.g. ptep_set_access_flags())
that is part of a contpte mapping, this change will affect the whole
contpte block. This is works fine in practice since we guarantee that
only a single folio is mapped by a contpte block, and the core-mm tracks
access/dirty information per folio.
In order for the public functions, which used to be pure inline, to
continue to be callable by modules, export all the contpte_* symbols that
are now called by those public inline functions.
The feature is enabled/disabled with the ARM64_CONTPTE Kconfig parameter
at build time. It defaults to enabled as long as its dependency,
TRANSPARENT_HUGEPAGE is also enabled. The core-mm depends upon
TRANSPARENT_HUGEPAGE to be able to allocate large folios, so if its not
enabled, then there is no chance of meeting the physical contiguity
requirement for contpte mappings.
Link: https://lkml.kernel.org/r/20240215103205.2607016-13-ryan.roberts@arm.com
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: John Hubbard <jhubbard@nvidia.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Barry Song <21cnbao@gmail.com>
Cc: Borislav Petkov (AMD) <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Morse <james.morse@arm.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will@kernel.org>
Cc: Yang Shi <shy828301@gmail.com>
Cc: Zi Yan <ziy@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Split __flush_tlb_range() into __flush_tlb_range_nosync() +
__flush_tlb_range(), in the same way as the existing flush_tlb_page()
arrangement. This allows calling __flush_tlb_range_nosync() to elide the
trailing DSB. Forthcoming "contpte" code will take advantage of this when
clearing the young bit from a contiguous range of ptes.
Ordering between dsb and mmu_notifier_arch_invalidate_secondary_tlbs() has
changed, but now aligns with the ordering of __flush_tlb_page(). It has
been discussed that __flush_tlb_page() may be wrong though. Regardless,
both will be resolved separately if needed.
Link: https://lkml.kernel.org/r/20240215103205.2607016-12-ryan.roberts@arm.com
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Tested-by: John Hubbard <jhubbard@nvidia.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Barry Song <21cnbao@gmail.com>
Cc: Borislav Petkov (AMD) <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Morse <james.morse@arm.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will@kernel.org>
Cc: Yang Shi <shy828301@gmail.com>
Cc: Zi Yan <ziy@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Create a new layer for the in-table PTE manipulation APIs. For now, The
existing API is prefixed with double underscore to become the arch-private
API and the public API is just a simple wrapper that calls the private
API.
The public API implementation will subsequently be used to transparently
manipulate the contiguous bit where appropriate. But since there are
already some contig-aware users (e.g. hugetlb, kernel mapper), we must
first ensure those users use the private API directly so that the future
contig-bit manipulations in the public API do not interfere with those
existing uses.
The following APIs are treated this way:
- ptep_get
- set_pte
- set_ptes
- pte_clear
- ptep_get_and_clear
- ptep_test_and_clear_young
- ptep_clear_flush_young
- ptep_set_wrprotect
- ptep_set_access_flags
Link: https://lkml.kernel.org/r/20240215103205.2607016-11-ryan.roberts@arm.com
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Tested-by: John Hubbard <jhubbard@nvidia.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Barry Song <21cnbao@gmail.com>
Cc: Borislav Petkov (AMD) <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Morse <james.morse@arm.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will@kernel.org>
Cc: Yang Shi <shy828301@gmail.com>
Cc: Zi Yan <ziy@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
ptep_clear() is a generic wrapper around the arch-implemented
ptep_get_and_clear(). We are about to convert ptep_get_and_clear() into a
public version and private version (__ptep_get_and_clear()) to support the
transparent contpte work. We won't have a private version of ptep_clear()
so let's convert it to directly call ptep_get_and_clear().
Link: https://lkml.kernel.org/r/20240215103205.2607016-10-ryan.roberts@arm.com
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Tested-by: John Hubbard <jhubbard@nvidia.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Barry Song <21cnbao@gmail.com>
Cc: Borislav Petkov (AMD) <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Morse <james.morse@arm.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will@kernel.org>
Cc: Yang Shi <shy828301@gmail.com>
Cc: Zi Yan <ziy@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Since set_ptes() was introduced, set_pte_at() has been implemented as a
generic macro around set_ptes(..., 1). So this change should continue to
generate the same code. However, making this change prepares us for the
transparent contpte support. It means we can reroute set_ptes() to
__set_ptes(). Since set_pte_at() is a generic macro, there will be no
equivalent __set_pte_at() to reroute to.
Note that a couple of calls to set_pte_at() remain in the arch code. This
is intentional, since those call sites are acting on behalf of core-mm and
should continue to call into the public set_ptes() rather than the
arch-private __set_ptes().
Link: https://lkml.kernel.org/r/20240215103205.2607016-9-ryan.roberts@arm.com
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Tested-by: John Hubbard <jhubbard@nvidia.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Barry Song <21cnbao@gmail.com>
Cc: Borislav Petkov (AMD) <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Morse <james.morse@arm.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will@kernel.org>
Cc: Yang Shi <shy828301@gmail.com>
Cc: Zi Yan <ziy@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
There are a number of places in the arch code that read a pte by using the
READ_ONCE() macro. Refactor these call sites to instead use the
ptep_get() helper, which itself is a READ_ONCE(). Generated code should
be the same.
This will benefit us when we shortly introduce the transparent contpte
support. In this case, ptep_get() will become more complex so we now have
all the code abstracted through it.
Link: https://lkml.kernel.org/r/20240215103205.2607016-8-ryan.roberts@arm.com
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Tested-by: John Hubbard <jhubbard@nvidia.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Barry Song <21cnbao@gmail.com>
Cc: Borislav Petkov (AMD) <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Morse <james.morse@arm.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will@kernel.org>
Cc: Yang Shi <shy828301@gmail.com>
Cc: Zi Yan <ziy@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Core-mm needs to be able to advance the pfn by an arbitrary amount, so
override the new pte_advance_pfn() API to do so.
Link: https://lkml.kernel.org/r/20240215103205.2607016-5-ryan.roberts@arm.com
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Acked-by: David Hildenbrand <david@redhat.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Barry Song <21cnbao@gmail.com>
Cc: Borislav Petkov (AMD) <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Morse <james.morse@arm.com>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will@kernel.org>
Cc: Yang Shi <shy828301@gmail.com>
Cc: Zi Yan <ziy@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Add the generated executable for relacheck to the list of ignored files.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20240222210441.33142-1-brgl@bgdev.pl
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
At present nothing in our CPU initialisation code ever sets unknown fields
in SMCR_EL1 to known values, all updates to SMCR_EL1 are read/modify/write
sequences. All the unknown fields are RES0, explicitly initialise them as
such to avoid future surprises.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20240213-arm64-fp-init-vec-cr-v1-2-7e7c2d584f26@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
At present nothing in our CPU initialisation code ever sets unknown fields
in ZCR_EL1 to known values, all updates to ZCR_EL1 are read/modify/write
sequences for LEN. All the unknown fields are RES0, explicitly initialise
them as such to avoid future surprises.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20240213-arm64-fp-init-vec-cr-v1-1-7e7c2d584f26@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
__SVE_VQ_MAX is defined without comment as 512 but the actual
architectural maximum is 16, a substantial difference which might not
be obvious to readers especially given the several different units used
for specifying vector sizes in various contexts and the fact that it's
often used via macros. In an effort to minimise surprises for users who
might assume the value is the architectural maximum and use it to do
things like size allocations add a comment noting the difference, and
add a note for SVE_VQ_MAX to aid discoverability.
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Dave Martin <Dave.Martin@arm.com>
Link: https://lore.kernel.org/r/20240209-arm64-sve-vl-max-comment-v2-1-111b283469ee@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In struct pt_regs, member pstate is after member pc. Move offset macro
of pstate after offset macro of pc to improve readability a little.
Signed-off-by: Kemeng Shi <shikemeng@huaweicloud.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20240130175504.106364-1-shikemeng@huaweicloud.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Enable PSTORE_RAM, that is the ramoops driver, in the defconfig, to
allow logging and retrieving panics and oopses to/from RAM automatically
for platforms that have a ramoops reserved memory node in DT.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: David Heidelberg <david@ixit.cz>
Link: https://lore.kernel.org/r/20240110210600.787703-3-nfraprado@collabora.com
Signed-off-by: Kees Cook <keescook@chromium.org>
All platforms could benefit from page order check against MAX_PAGE_ORDER
before allocating a CMA area for gigantic hugetlb pages. Let's move this
check from individual platforms to generic hugetlb.
Link: https://lkml.kernel.org/r/20240209054221.1403364-1-anshuman.khandual@arm.com
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Reviewed-by: Jane Chu <jane.chu@oracle.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Patch series "mm/memory: optimize fork() with PTE-mapped THP", v3.
Now that the rmap overhaul[1] is upstream that provides a clean interface
for rmap batching, let's implement PTE batching during fork when
processing PTE-mapped THPs.
This series is partially based on Ryan's previous work[2] to implement
cont-pte support on arm64, but its a complete rewrite based on [1] to
optimize all architectures independent of any such PTE bits, and to use
the new rmap batching functions that simplify the code and prepare for
further rmap accounting changes.
We collect consecutive PTEs that map consecutive pages of the same large
folio, making sure that the other PTE bits are compatible, and (a) adjust
the refcount only once per batch, (b) call rmap handling functions only
once per batch and (c) perform batch PTE setting/updates.
While this series should be beneficial for adding cont-pte support on
ARM64[2], it's one of the requirements for maintaining a total mapcount[3]
for large folios with minimal added overhead and further changes[4] that
build up on top of the total mapcount.
Independent of all that, this series results in a speedup during fork with
PTE-mapped THP, which is the default with THPs that are smaller than a PMD
(for example, 16KiB to 1024KiB mTHPs for anonymous memory[5]).
On an Intel Xeon Silver 4210R CPU, fork'ing with 1GiB of PTE-mapped folios
of the same size (stddev < 1%) results in the following runtimes for
fork() (shorter is better):
Folio Size | v6.8-rc1 | New | Change
------------------------------------------
4KiB | 0.014328 | 0.014035 | - 2%
16KiB | 0.014263 | 0.01196 | -16%
32KiB | 0.014334 | 0.01094 | -24%
64KiB | 0.014046 | 0.010444 | -26%
128KiB | 0.014011 | 0.010063 | -28%
256KiB | 0.013993 | 0.009938 | -29%
512KiB | 0.013983 | 0.00985 | -30%
1024KiB | 0.013986 | 0.00982 | -30%
2048KiB | 0.014305 | 0.010076 | -30%
Note that these numbers are even better than the ones from v1 (verified
over multiple reboots), even though there were only minimal code changes.
Well, I removed a pte_mkclean() call for anon folios, maybe that also
plays a role.
But my experience is that fork() is extremely sensitive to code size,
inlining, ... so I suspect we'll see on other architectures rather a
change of -20% instead of -30%, and it will be easy to "lose" some of that
speedup in the future by subtle code changes.
Next up is PTE batching when unmapping. Only tested on x86-64.
Compile-tested on most other architectures.
[1] https://lkml.kernel.org/r/20231220224504.646757-1-david@redhat.com
[2] https://lkml.kernel.org/r/20231218105100.172635-1-ryan.roberts@arm.com
[3] https://lkml.kernel.org/r/20230809083256.699513-1-david@redhat.com
[4] https://lkml.kernel.org/r/20231124132626.235350-1-david@redhat.com
[5] https://lkml.kernel.org/r/20231207161211.2374093-1-ryan.roberts@arm.com
This patch (of 15):
Since the high bits [51:48] of an OA are not stored contiguously in the
PTE, there is a theoretical bug in set_ptes(), which just adds PAGE_SIZE
to the pte to get the pte with the next pfn. This works until the pfn
crosses the 48-bit boundary, at which point we overflow into the upper
attributes.
Of course one could argue (and Matthew Wilcox has :) that we will never
see a folio cross this boundary because we only allow naturally aligned
power-of-2 allocation, so this would require a half-petabyte folio. So
its only a theoretical bug. But its better that the code is robust
regardless.
I've implemented pte_next_pfn() as part of the fix, which is an opt-in
core-mm interface. So that is now available to the core-mm, which will be
needed shortly to support forthcoming fork()-batching optimizations.
Link: https://lkml.kernel.org/r/20240129124649.189745-1-david@redhat.com
Link: https://lkml.kernel.org/r/20240125173534.1659317-1-ryan.roberts@arm.com
Link: https://lkml.kernel.org/r/20240129124649.189745-2-david@redhat.com
Fixes: 4a169d61c2 ("arm64: implement the new page table range API")
Closes: https://lore.kernel.org/linux-mm/fdaeb9a5-d890-499a-92c8-d171df43ad01@arm.com/
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Tested-by: Ryan Roberts <ryan.roberts@arm.com>
Reviewed-by: Mike Rapoport (IBM) <rppt@kernel.org>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@kernel.org>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: David S. Miller <davem@davemloft.net>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Naveen N. Rao <naveen.n.rao@linux.ibm.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Russell King (Oracle) <linux@armlinux.org.uk>
Cc: Sven Schnelle <svens@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Alexandre Ghiti <alexghiti@rivosinc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
All architectures using the core ptdump functionality also implement
CONFIG_DEBUG_WX, and they all do it more or less the same way, with a
function called debug_checkwx() that is called by mark_rodata_ro(), which
is a substitute to ptdump_check_wx() when CONFIG_DEBUG_WX is set and a
no-op otherwise.
Refactor by centrally defining debug_checkwx() in linux/ptdump.h and call
debug_checkwx() immediately after calling mark_rodata_ro() instead of
calling it at the end of every mark_rodata_ro().
On x86_32, mark_rodata_ro() first checks __supported_pte_mask has _PAGE_NX
before calling debug_checkwx(). Now the check is inside the callee
ptdump_walk_pgd_level_checkwx().
On powerpc_64, mark_rodata_ro() bails out early before calling
ptdump_check_wx() when the MMU doesn't have KERNEL_RO feature. The check
is now also done in ptdump_check_wx() as it is called outside
mark_rodata_ro().
Link: https://lkml.kernel.org/r/a59b102d7964261d31ead0316a9f18628e4e7a8e.1706610398.git.christophe.leroy@csgroup.eu
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: "Aneesh Kumar K.V (IBM)" <aneesh.kumar@kernel.org>
Cc: Borislav Petkov (AMD) <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Cc: Greg KH <greg@kroah.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: "Naveen N. Rao" <naveen.n.rao@linux.ibm.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Phong Tran <tranmanphong@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Steven Price <steven.price@arm.com>
Cc: Sven Schnelle <svens@linux.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
In order to ease the transition towards a state of absolute
paranoia where all RES0/RES1 bits gets checked against what
KVM know of them, make the checks optional and guarded by a
config symbol (CONFIG_KVM_ARM64_RES_BITS_PARANOIA) default to n.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/kvm/87frxka7ud.wl-maz@kernel.org/
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
The MGBE power-domains on Tegra234 are mapped to the MGBE controllers as
follows:
MGBE0 (0x68000000) --> Power-Domain MGBEB
MGBE1 (0x69000000) --> Power-Domain MGBEC
MGBE2 (0x6a000000) --> Power-Domain MGBED
Update the device-tree nodes for Tegra234 to correct this.
Fixes: 610cdf3186 ("arm64: tegra: Add MGBE nodes on Tegra234")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Since commit c02433dd6d ("arm64: split thread_info from task stack"),
CONFIG_THREAD_INFO_IN_TASK is enabled unconditionally for arm64. So
remove this always-true assertion from arch_dup_task_struct.
Signed-off-by: Dawei Li <dawei.li@shingroup.cn>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20240202040211.3118918-1-dawei.li@shingroup.cn
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Enable CRU and CSI on RZ/G2UL SMARC EVK and tie the CSI to the OV5645
sensor using a Device Tree overlay.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240213141300.159847-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
All Ethernet AVB instances on R-Car V3U have registers related to UDP/IP
support, but the declared register blocks for the first two instances
are too small to cover them.
Fix this by extending the register block sizes.
Fixes: 5a633320f0 ("arm64: dts: renesas: r8a779a0: Add Ethernet-AVB support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/ce6ce3c4b1495e02e7c1803fca810a7178a84500.1707660323.git.geert+renesas@glider.be
Add PSCI support to enable suspend/resume with the help of TF-A.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240208135629.2840932-3-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Ethernet IRQ GPIOs are marked as GPIO hogs. Thus, these GPIOs are
requested at probe time without considering if there are other
peripherals that need them. The Ethernet IRQ GPIOs are shared with
SDHI2. Selection between Ethernet and SDHI2 is done through a hardware
switch. To avoid scenarios where one wants to boot with SDHI2 support
and some SDHI pins are not propertly configured because of the GPIO
hogs, guard the Ethernet IRQ GPIO hogs with the proper build flag.
Fixes: 932ff0c802 ("arm64: dts: renesas: rzg3s-smarc-som: Enable the Ethernet interfaces")
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240208124300.2740313-13-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sound uses the standard 5V supply, so rename the fixed regulator as
such. Also add properties documenting it is always on, also during boot.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240129212350.33370-3-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
It is named T1.8V in the schematics. Also add properties documenting it
is always on, also during boot.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240129212350.33370-2-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Without them, no power, so cards do not get recognized.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240129135840.28988-1-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
used instead of ignored, causing NULL pointer dereferences.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmXVztAUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroOgYgf/ftnjbTLvRZ56tgRNH13VXlhpgFIa
6H+DRQO2dEfEXFh9AbEeFJBZ7M6emXMCqtolh8a0Ulq09sPaI8jWwn6uST860l19
mzMJVRgbYZ7vbxq5bEuYovpMNg42mqMOu7sxWmu4pw0slPMfHftv5lNjaWVjC1RF
Ohb5d1ftglxuxS0EyewPdHpGpUpHsNfDZ6CilX4v+5mn9IKhJN++Afgy6YhaRriO
YICL1kYv+a43LRtNyq8aYWw7eEqD0OEbJVy4ZarBFTxdzqctNRuB1WXet1tE1rjU
qpBHhiGMPTuv4bXFksAdmMTV+Z/6tQ+/KLFyXPtQ/k+KubaxbVfRBAhIFg==
=Y5R6
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"Two fixes for ARM ITS emulation. Unmapped interrupts were used instead
of ignored, causing NULL pointer dereferences"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: arm64: vgic-its: Test for valid IRQ in MOVALL handler
KVM: arm64: vgic-its: Test for valid IRQ in its_sync_lpi_pending_table()
Add the Chips and Media wave521cl video decoder/encoder node on J721S2.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Brandon Brnich <b-brnich@ti.com>
Link: https://lore.kernel.org/r/20240220191413.3355007-3-b-brnich@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
AM69 SK has S28HS512T OSPI flash connected to MCU OSPI0.
Enable support for the same. Also describe the partition
information according to the offsets in the bootloader.
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Dasnavis Sabiya <sabiya.d@ti.com>
Link: https://lore.kernel.org/r/20240220162527.663394-3-sabiya.d@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
AM69 SK board has several CAN bus interfaces on both MCU and MAIN domains.
This enables the CAN interfaces on MCU and MAIN domain.
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Dasnavis Sabiya <sabiya.d@ti.com>
Link: https://lore.kernel.org/r/20240220162527.663394-2-sabiya.d@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Enable symbols so that overlays can be applied on the base DTB for
SK-AM62P.
Also compile-test known-to-work camera sensor overlays for OV5640 and
IMX219.
Reviewed-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240220-am62p_csi-v2-4-3e71d9945571@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
AM62P supports image capture via the MIPI CSI-2 protocol, it uses three
IPs to achieve this: Cadence DPHY, Cadence CSI-RX, and TI's pixelgrabber
wrapper on top. Add nodes for these IPs in the devicetree, and keep them
disabled here, so these may be enabled by the sensor overlays.
Reviewed-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240220-am62p_csi-v2-3-3e71d9945571@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
On AM62P, CSI-RX uses a dedicated BCDMA instance (DMASS1) for
transferring captured camera frames to DDR, so enable it.
Reviewed-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240220-am62p_csi-v2-2-3e71d9945571@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The INTR module for DMASS1 (CSI specific DMASS) is outside the currently
available ranges, as it starts at 0x4e400000. So fix the ranges property
to enable programming the interrupts correctly.
Fixes: 29075cc09f ("arm64: dts: ti: Introduce AM62P5 family of SoCs")
Reviewed-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240220-am62p_csi-v2-1-3e71d9945571@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
J722S EVM has S28HS512T 64 MiB Octal SPI NOR flash connected
to the OSPI interface, add support for the flash and describe
the partition information as per bootloader.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Link: https://lore.kernel.org/r/20240219090435.934383-3-vaishnav.a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Enable MAC Port 1 of CPSW3G instance of CPSW Ethernet Switch in
RGMII-RXID mode of operation. Port 2 is not connected on the EVM,
thus keep it disabled.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Link: https://lore.kernel.org/r/20240219090435.934383-2-vaishnav.a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Change offset in mux-reg-masks property for serdes_ln_ctrl node
since reg-mux property is used in compatible.
Fixes: 2765149273 ("mux: mmio: use reg property when parent device is not a syscon")
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
Acked-by: Andrew Davis <afd@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20240213080348.248916-1-s-vadapalli@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Change offset in mux-reg-masks property for hbmc_mux node
since reg-mux property is used in compatible.
While here, update the reg region to include 4 bytes as this
is a 32bit register.
Fixes: 2765149273 ("mux: mmio: use reg property when parent device is not a syscon")
Suggested-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240215141957.13775-1-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Tegra234 boards use a mixture of aliases for the SD/MMC hardware blocks,
which can lead to confusion. A common method was to use mmc3 as the
alias for the eMMC because "SDMMC3" happens to be the name of the
corresponding controller in the reference manual. This isn't a great
choice because there is no hardware named SDMMC0, so the mmc0 alias
would never get used with that nomenclature and in fact mmc1 and mmc2
wouldn't either in many configurations, thereby creating weird
discontiguous enumeration.
Instead of trying to match the aliases to the hardware block names, use
mmc0 to denote the device's primary SD/MMC controller (typically eMMC)
and mmc1 for the secondary SD/MMC controller (typically removable SD).
In cases where eMMC is the only controller we can omit the mmc1 alias
and if a device has no eMMC, the removable SD card can be aliased to
mmc0 instead.
Co-developed-by: Russell Xiao <russellx@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
- Check for the validity of interrupts handled by a MOVALL
command
- Check for the validity of interrupts while reading the
pending state on enabling LPIs.
-----BEGIN PGP SIGNATURE-----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=cHkQ
-----END PGP SIGNATURE-----
Merge tag 'kvmarm-fixes-6.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm64 fixes for 6.8, take #3
- Check for the validity of interrupts handled by a MOVALL
command
- Check for the validity of interrupts while reading the
pending state on enabling LPIs.
It is possible that an LPI mapped in a different ITS gets unmapped while
handling the MOVALL command. If that is the case, there is no state that
can be migrated to the destination. Silently ignore it and continue
migrating other LPIs.
Cc: stable@vger.kernel.org
Fixes: ff9c114394 ("KVM: arm/arm64: GICv4: Handle MOVALL applied to a vPE")
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Link: https://lore.kernel.org/r/20240221092732.4126848-3-oliver.upton@linux.dev
Signed-off-by: Marc Zyngier <maz@kernel.org>
vgic_get_irq() may not return a valid descriptor if there is no ITS that
holds a valid translation for the specified INTID. If that is the case,
it is safe to silently ignore it and continue processing the LPI pending
table.
Cc: stable@vger.kernel.org
Fixes: 33d3bc9556 ("KVM: arm64: vgic-its: Read initial LPI pending table")
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Link: https://lore.kernel.org/r/20240221092732.4126848-2-oliver.upton@linux.dev
Signed-off-by: Marc Zyngier <maz@kernel.org>
The PCI node interrupt-map properties have the wrong size as #address-cells
in the interrupt parent are not accounted for.
The dtc interrupt_map check catches this, but the warning is off because
its dependency, interrupt_provider, is off by default.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20240213-arm-dt-cleanups-v1-5-f2dee1292525@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The dtc interrupt_provider warning is off by default. Fix all the warnings
so it can be enabled.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-By: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> #
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com> #Broadcom
Acked-by: Chanho Min <chanho.min@lge.com>
Link: https://lore.kernel.org/r/20240213-arm-dt-cleanups-v1-3-f2dee1292525@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Several Freescale Layerscape platforms extirq binding use a malformed
interrupt-map property missing parent address cells. These are
documented in of_irq_imap_abusers list in drivers/of/irq.c. In order to
enable dtc interrupt_map check tree wide, we need to disable it for
these platforms which will not be fixed (as that would break
compatibility).
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20240213-arm-dt-cleanups-v1-1-f2dee1292525@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Disable obsolete board staging support in the Renesas ARM and ARM V7
multi-platform defconfigs,
- Enable support for the Renesas R-Car V4M (R8A779H0) SoC in the ARM64
defconfig.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCZcYucgAKCRCKwlD9ZEnx
cFKJAQCpdfJuHtpm6sDIv6JWuVmmDMOHwRw7tQ5UNeYRZMXuHAEAt4R+6mYRTo4L
LCWTcwzprYeOnEO/4Oemnv3CTDiA6Ag=
=oJfk
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=BT6t
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm-defconfig-for-v6.9-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into soc/defconfig
Renesas ARM defconfig updates for v6.9
- Disable obsolete board staging support in the Renesas ARM and ARM V7
multi-platform defconfigs,
- Enable support for the Renesas R-Car V4M (R8A779H0) SoC in the ARM64
defconfig.
* tag 'renesas-arm-defconfig-for-v6.9-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
arm64: defconfig: Enable R8A779H0 SoC
ARM: multi_v7_defconfig: Disable board staging
ARM: shmobile: defconfig: Disable staging
Link: https://lore.kernel.org/r/cover.1707487828.git.geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
styling fixes (unneeded jaguar status, whitespaces, Cool Pi regulator
naming) and functionality fixes (px30 spi chipselect number, allowing
rk3588-evb1 to turn off, pcie lane numbers on CoolPi, wrong gpio-names
on Indidroid Nova and some CoolPi sdmmc aliases to match what uboot uses).
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAmXLyiQQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgSSOB/9GsWQ1KbuTB5XQlnfNM9c/YQRlMF6olXbd
m2Lhf7B6KDQiAtINtPSe2c3o1Ym2BFISYlHd3HjmUGiedacs8cdFdzaIcyDO4LIH
WwlqwdWrWuL5w5UqON3M+iY4BmQPtgNOBeDlD45GU1WL25C5EarWk2pUpYQ3M/UR
LvmGgm3LQzEGaCaNzQujyIhRuH8dGBryBfbzy5HRGt2QPZo1aayzLQ2i2HUoRraO
WZnTSVYvQfnDoNz9nr+P8ZggnbXSWMErnuwXAVkFw7vBpXvTOGV/3xnKPHKMCMrg
ZgnkdLHfj0z/35E2HWCoJeEDYqCTKoRz9bfDuo8q6Zd8p13qMDxW
=PhSL
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=yDjC
-----END PGP SIGNATURE-----
Merge tag 'v6.8-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/fixes
Some fixes to make devicetrees conform to bindings better (pwm irqs), dt
styling fixes (unneeded jaguar status, whitespaces, Cool Pi regulator
naming) and functionality fixes (px30 spi chipselect number, allowing
rk3588-evb1 to turn off, pcie lane numbers on CoolPi, wrong gpio-names
on Indidroid Nova and some CoolPi sdmmc aliases to match what uboot uses).
* tag 'v6.8-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Correct Indiedroid Nova GPIO Names
arm64: dts: rockchip: Drop interrupts property from rk3328 pwm-rockchip node
arm64: dts: rockchip: set num-cs property for spi on px30
arm64: dts: rockchip: minor rk3588 whitespace cleanup
arm64: dts: rockchip: drop unneeded status from rk3588-jaguar gpio-leds
ARM: dts: rockchip: Drop interrupts property from pwm-rockchip nodes
arm64: dts: rockchip: Fix the num-lanes of pcie3x4 on Cool Pi CM5 EVB
arm64: dts: rockchip: rename vcc5v0_usb30_host regulator for Cool Pi CM5 EVB
arm64: dts: rockchip: aliase sdmmc as mmc1 for Cool Pi CM5 EVB
arm64: dts: rockchip: aliase sdmmc as mmc1 for Cool Pi 4B
arm64: dts: rockchip: mark system power controller on rk3588-evb1
Link: https://lore.kernel.org/r/2450634.jE0xQCEvom@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There is already a generic union definition for vdso_data_store in vdso
datapage header.
Use this definition to prevent code duplication.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20240219153939.75719-6-anna-maria@linutronix.de
On arm64, kprobes always take an exception and so create a struct
pt_regs through the usual exception entry logic. Similarly kretprobes
taskes and exception for function entry, but for function returns it
uses a trampoline which attempts to create a struct pt_regs without
taking an exception.
This is problematic for a few reasons, including:
1) The kretprobes trampoline neither saves nor restores all of the
portions of PSTATE. Before invoking the handler it saves a number of
portions of PSTATE, and after returning from the handler it restores
NZCV before returning to the original return address provided by the
handler.
2) The kretprobe trampoline constructs the PSTATE value piecemeal from
special purpose registers as it cannot read all of PSTATE atomically
without taking an exception. This is somewhat fragile, and it's not
possible to reliably recover PSTATE information which only exists on
some physical CPUs (e.g. when SSBS support is mismatched).
Today the kretprobes trampoline does not record:
- BTYPE
- SSBS
- ALLINT
- SS
- PAN
- UAO
- DIT
- TCO
... and this will only get worse with future architecture extensions
which add more PSTATE bits.
3) The kretprobes trampoline doesn't store portions of struct pt_regs
(e.g. the PMR value when using pseudo-NMIs). Due to this, helpers
which operate on a struct pt_regs, such as interrupts_enabled(), may
not work correctly.
4) The function entry and function exit handlers run in different
contexts. The entry handler will always be run in a debug exception
context (which is currently treated as an NMI), but the return will
be treated as whatever context the instrumented function was executed
in. The differences between these contexts are liable to cause
problems (e.g. as the two can be differently interruptible or
preemptible, adversely affecting synchronization between the
handlers).
5) As the kretprobes trampoline runs in the same context as the code
being probed, it is subject to the same single-stepping context,
which may not be desirable if this is being driven by the kprobes
handlers.
Overall, this is fragile, painful to maintain, and gets in the way of
supporting other things (e.g. RELIABLE_STACKTRACE, FEAT_NMI).
This patch addresses these issues by replacing the kretprobes trampoline
with a `BRK` instruction, and using an exception boundary to acquire and
restore the regs, in the same way as the regular kprobes trampoline.
Ive tested this atop v6.8-rc3:
| KTAP version 1
| 1..1
| KTAP version 1
| # Subtest: kprobes_test
| # module: test_kprobes
| 1..7
| ok 1 test_kprobe
| ok 2 test_kprobes
| ok 3 test_kprobe_missed
| ok 4 test_kretprobe
| ok 5 test_kretprobes
| ok 6 test_stacktrace_on_kretprobe
| ok 7 test_stacktrace_on_nested_kretprobe
| # kprobes_test: pass:7 fail:0 skip:0 total:7
| # Totals: pass:7 fail:0 skip:0 total:7
| ok 1 kprobes_test
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Florent Revest <revest@chromium.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Link: https://lore.kernel.org/r/20240208145916.2004154-1-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When returning to a user context, the arm64 entry code masks all DAIF
exceptions before handling pending work in exit_to_user_mode_prepare()
and do_notify_resume(), where it will transiently unmask all DAIF
exceptions. This is a holdover from the old entry assembly, which
conservatively masked all DAIF exceptions, and it's only necessary to
mask interrupts at this point during the exception return path, so long
as we subsequently mask all DAIF exceptions before the actual exception
return.
While most DAIF manipulation follows a save...restore sequence, the
manipulation in do_notify_resume() is the other way around, unmasking
all DAIF exceptions before masking them again. This is unfortunate as we
unnecessarily mask Debug and SError exceptions, and it would be nice to
remove this special case to make DAIF manipulation simpler and most
consistent.
This patch changes exit_to_user_mode_prepare() and do_notify_resume() to
only mask interrupts while handling pending work, masking other DAIF
exceptions after this has completed. This removes the unusual DAIF
manipulation and allows Debug and SError exceptions to be taken for a
slightly longer window during the exception return path.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20240206123848.1696480-4-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Itaru Kitayama <itaru.kitayama@linux.dev>
Currently do_notify_resume() lives in arch/arm64/kernel/signal.c, but it would
make more sense for it to live in entry-common.c as it handles more than
signals, and is coupled with the rest of the return-to-userspace sequence (e.g.
with unusual DAIF masking that matches the exception return requirements).
Move do_notify_resume() to entry-common.c.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20240206123848.1696480-3-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Itaru Kitayama <itaru.kitayama@linux.dev>
In do_notify_resume, we handle _TIF_NEED_RESCHED differently from all
other flags, leaving IRQ+FIQ masked when calling into schedule(). This
masking is a historical artifact, and it is not currently necessary
to mask IRQ+FIQ when calling into schedule (as evidenced by the generic
exit_to_user_mode_loop(), which unmasks IRQs before checking
_TIF_NEED_RESCHED and calling schedule()).
This patch removes the special case for _TIF_NEED_RESCHED, moving this
check into the main loop such that schedule() will be called from a
regular process context with IRQ+FIQ unmasked. This is a minor
simplification to do_notify_resume() and brings it into line with the
generic exit_to_user_mode_loop() logic. This will also aid subsequent
rework of DAIF management.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20240206123848.1696480-2-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Itaru Kitayama <itaru.kitayama@linux.dev>
Currently our IO accessors all use register addressing without offsets,
but we could safely use offset addressing (without writeback) to
simplify and optimize the generated code.
To function correctly under a hypervisor which emulates IO accesses, we
must ensure that any faulting/trapped IO access results in an ESR_ELx
value with ESR_ELX.ISS.ISV=1 and with the tranfer register described in
ESR_ELx.ISS.SRT. This means that we can only use loads/stores of a
single general purpose register (or the zero register), and must avoid
writeback addressing modes. However, we can use immediate offset
addressing modes, as these still provide ESR_ELX.ISS.ISV=1 and a valid
ESR_ELx.ISS.SRT when those accesses fault at Stage-2.
Currently we only use register addressing without offsets. We use the
"r" constraint to place the address into a register, and manually
generate the register addressing by surrounding the resulting register
operand with square braces, e.g.
| static __always_inline void __raw_writeq(u64 val, volatile void __iomem *addr)
| {
| asm volatile("str %x0, [%1]" : : "rZ" (val), "r" (addr));
| }
Due to this, sequences of adjacent accesses need to generate addresses
using separate instructions. For example, the following code:
| void writeq_zero_8_times(void *ptr)
| {
| writeq_relaxed(0, ptr + 8 * 0);
| writeq_relaxed(0, ptr + 8 * 1);
| writeq_relaxed(0, ptr + 8 * 2);
| writeq_relaxed(0, ptr + 8 * 3);
| writeq_relaxed(0, ptr + 8 * 4);
| writeq_relaxed(0, ptr + 8 * 5);
| writeq_relaxed(0, ptr + 8 * 6);
| writeq_relaxed(0, ptr + 8 * 7);
| }
... is compiled to:
| <writeq_zero_8_times>:
| str xzr, [x0]
| add x1, x0, #0x8
| str xzr, [x1]
| add x1, x0, #0x10
| str xzr, [x1]
| add x1, x0, #0x18
| str xzr, [x1]
| add x1, x0, #0x20
| str xzr, [x1]
| add x1, x0, #0x28
| str xzr, [x1]
| add x1, x0, #0x30
| str xzr, [x1]
| add x0, x0, #0x38
| str xzr, [x0]
| ret
As described above, we could safely use immediate offset addressing,
which would allow the ADDs to be folded into the address generation for
the STRs, resulting in simpler and smaller generated assembly. We can do
this by using the "o" constraint to allow the compiler to generate
offset addressing (without writeback) for a memory operand, e.g.
| static __always_inline void __raw_writeq(u64 val, volatile void __iomem *addr)
| {
| volatile u64 __iomem *ptr = addr;
| asm volatile("str %x0, %1" : : "rZ" (val), "o" (*ptr));
| }
... which results in the earlier code sequence being compiled to:
| <writeq_zero_8_times>:
| str xzr, [x0]
| str xzr, [x0, #8]
| str xzr, [x0, #16]
| str xzr, [x0, #24]
| str xzr, [x0, #32]
| str xzr, [x0, #40]
| str xzr, [x0, #48]
| str xzr, [x0, #56]
| ret
As Will notes at:
https://lore.kernel.org/linux-arm-kernel/20240117160528.GA3398@willie-the-truck/
... some compilers struggle with a plain "o" constraint, so it's
preferable to use "Qo", where the additional "Q" constraint permits
using non-offset register addressing.
This patch modifies our IO write accessors to use "Qo" constraints,
resulting in the better code generation described above. The IO read
accessors are left as-is because ARM64_WORKAROUND_DEVICE_LOAD_ACQUIRE
requires that non-offset register addressing is used, as the LDAR
instruction does not support offset addressing.
When compiling v6.8-rc1 defconfig with GCC 13.2.0, this saves ~4KiB of
text:
| [mark@lakrids:~/src/linux]% ls -al vmlinux-*
| -rwxr-xr-x 1 mark mark 153960576 Jan 23 12:01 vmlinux-after
| -rwxr-xr-x 1 mark mark 153862192 Jan 23 11:57 vmlinux-before
|
| [mark@lakrids:~/src/linux]% size vmlinux-before vmlinux-after
| text data bss dec hex filename
| 26708921 16690350 622736 44022007 29fb8f7 vmlinux-before
| 26704761 16690414 622736 44017911 29fa8f7 vmlinux-after
... though due to internal alignment of sections, this has no impact on
the size of the resulting Image:
| [mark@lakrids:~/src/linux]% ls -al Image-*
| -rw-r--r-- 1 mark mark 43590144 Jan 23 12:01 Image-after
| -rw-r--r-- 1 mark mark 43590144 Jan 23 11:57 Image-before
Aside from the better code generation, there should be no functional
change as a result of this patch. I have lightly tested this patch,
including booting under KVM (where some devices such as PL011 are
emulated).
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Jason Gunthorpe <jgg@nvidia.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20240124111259.874975-1-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Arm classifies some of its CPU errata as "rare", indicating that the
hardware error is unlikely to occur in practice. Given that the cost of
errata workarounds can often be significant in terms of power and
performance, don't enable workarounds for "rare" errata by default and
update our documentation to reflect that.
Cc: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20240209183916.25860-1-will@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The patch adding Type-C support for sm6115 was misapplied. All the
orientation switch configuration ended up at the UFS PHY node instead of
the USB PHY node. Move the data bits to the correct place.
Fixes: a06a2f12f9 ("arm64: dts: qcom: qrb4210-rb2: enable USB-C port handling")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240220173104.3052778-1-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
- A tqma8mpql device tree fix to correct audio codec iov-supply.
- A couple of USB-C connector DT description revert to fix regression
on imx8mp-dhcom-pdk3 and imx8mn-var-som-symphony board.
- Fix valid range check for imx-weim bus driver.
- Disable UART4 on Data Modul i.MX8M Plus eDM SBC to avoid boot hang
in case that RDC protection is in place.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAmXCSosUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM7NFQf/TkWrn6KnVCZVufjlYmrgtRyyWa3Q
rjQPNijBupcA9S+hlLDbrtxzv3JeZmZs3VOHitikc7CuAc+WMjZB52VmU1UU6r5i
2irWTy1OauixofZYoC61Yvp/tLLbZCX+O3Y/nCeeBLKxPt3hXNmuILONmnnWeLOH
WigqOqdEm1XP54YSgTFbwTblAJJo+Avot3pJxl8j3CWa/RY9hKGNUzi5z4t1KZmK
X5zKLJA+maR+mM+toGHxvkLu7g6sa74ft16lmGnvAI/l09hrbdwT02q4cLs4jLaD
e29Y0A92bPCWQVsKEcE1Jxj0Fe4pKsYE+6C+MCEQOSqp+jaCJSxhWu7tXA==
=Zs1T
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=y9iD
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 6.8:
- A tqma8mpql device tree fix to correct audio codec iov-supply.
- A couple of USB-C connector DT description revert to fix regression
on imx8mp-dhcom-pdk3 and imx8mn-var-som-symphony board.
- Fix valid range check for imx-weim bus driver.
- Disable UART4 on Data Modul i.MX8M Plus eDM SBC to avoid boot hang
in case that RDC protection is in place.
* tag 'imx-fixes-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
bus: imx-weim: fix valid range check
Revert "arm64: dts: imx8mn-var-som-symphony: Describe the USB-C connector"
Revert "arm64: dts: imx8mp-dhcom-pdk3: Describe the USB-C connector"
arm64: dts: tqma8mpql: fix audio codec iov-supply
arm64: dts: imx8mp: Disable UART4 by default on Data Modul i.MX8M Plus eDM SBC
Link: https://lore.kernel.org/r/20240206151744.2459-1-shawnguo2@yeah.net
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The fields in SMCR_EL1 reset to an architecturally UNKNOWN value. Since we
do not otherwise manage the traps configured in this register at runtime we
need to reconfigure them after a suspend in case nothing else was kind
enough to preserve them for us. Do so for SMCR_EL1.EZT0.
Fixes: d4913eee15 ("arm64/sme: Add basic enumeration for SME2")
Reported-by: Jackson Cooper-Driver <Jackson.Cooper-Driver@arm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20240213-arm64-sme-resume-v3-2-17e05e493471@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
The fields in SMCR_EL1 and SMPRI_EL1 reset to an architecturally UNKNOWN
value. Since we do not otherwise manage the traps configured in this
register at runtime we need to reconfigure them after a suspend in case
nothing else was kind enough to preserve them for us.
The vector length will be restored as part of restoring the SME state for
the next SME using task.
Fixes: a1f4ccd25c ("arm64/sme: Provide Kconfig for SME")
Reported-by: Jackson Cooper-Driver <Jackson.Cooper-Driver@arm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20240213-arm64-sme-resume-v3-1-17e05e493471@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
This reverts commit f9daab0ad0.
Geert reports that his particular GCC 5.5 vintage toolchain fails to
build an arm64 defconfig because of this change:
| arch/arm64/include/asm/jump_label.h:25:2: error: invalid 'asm':
| invalid operand
| asm goto(
^
Aopparently, this is something we claim to support, so let's revert back
to the old jump label constraint for now while discussions about raising
the minimum GCC version are ongoing.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/CAMuHMdX+6fnAf8Hm6EqYJPAjrrLO9T7c=Gu3S8V_pqjSDowJ6g@mail.gmail.com
Signed-off-by: Will Deacon <will@kernel.org>
Debugging ID register setup can be a complicated affair. Give the
kernel hacker a way to dump that state in an easy to parse way.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240214131827.2856277-27-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
As KVM now strongly relies on accurately handling the RES0/RES1 bits
on a number of paths, add a compile-time checker that will blow in
the face of the innocent bystander, should they try to sneak in an
update that changes any of these RES0/RES1 fields.
It is expected that such an update will come with the relevant
KVM update if needed.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240214131827.2856277-26-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
We unconditionally enable FEAT_MOPS, which is obviously wrong.
So let's only do that when it is advertised to the guest.
Which means we need to rely on a per-vcpu HCRX_EL2 shadow register.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Link: https://lore.kernel.org/r/20240214131827.2856277-25-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
No AMU? No AMU! IF we see an AMU-related trap, let's turn it into
an UNDEF!
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240214131827.2856277-24-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
As part of the ongoing effort to honor the guest configuration,
add the necessary checks to make PIR_EL1 and co UNDEF if not
advertised to the guest, and avoid context switching them.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Link: https://lore.kernel.org/r/20240214131827.2856277-23-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Outer Shareable and Range TLBI instructions shouldn't be made available
to the guest if they are not advertised. Use FGU to disable those,
and set HCR_EL2.TLBIOS in the case the host doesn't have FGT. Note
that in that later case, we cannot efficiently disable TLBI Range
instructions, as this would require to trap all TLBIs.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Link: https://lore.kernel.org/r/20240214131827.2856277-22-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
The way we save/restore HFG[RW]TR_EL2 can now be simplified, and
the Ampere erratum hack is the only thing that still stands out.
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240214131827.2856277-21-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
We already trap a bunch of existing features for the purpose of
disabling them (MAIR2, POR, ACCDATA, SME...).
Let's move them over to our brand new FGU infrastructure.
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240214131827.2856277-20-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
In order to correctly honor our FGU bits, they must be converted
into a set of FGT bits. They get merged as part of the existing
FGT setting.
Similarly, the UNDEF injection phase takes place when handling
the trap.
This results in a bit of rework in the FGT macros in order to
help with the code generation, as burying per-CPU accesses in
macros results in a lot of expansion, not to mention the vcpu->kvm
access on nvhe (kern_hyp_va() is not optimisation-friendly).
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240214131827.2856277-19-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
In order to efficiently handle system register access being disabled,
and this resulting in an UNDEF exception being injected, we introduce
the (slightly dubious) concept of Fine-Grained UNDEF, modeled after
the architectural Fine-Grained Traps.
For each FGT group, we keep a 64 bit word that has the exact same
bit assignment as the corresponding FGT register, where a 1 indicates
that trapping this register should result in an UNDEF exception being
reinjected.
So far, nothing populates this information, nor sets the corresponding
trap bits.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240214131827.2856277-18-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
__check_nv_sr_forward() is not specific to NV anymore, and does
a lot more. Rename it to triage_sysreg_trap(), making it plain
that its role is to handle where an exception is to be handled.
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240214131827.2856277-17-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Since we always start sysreg/sysinsn handling by searching the
xarray, use it as the source of the index in the correct sys_reg_desc
array.
This allows some cleanup, such as moving the handling of unknown
sysregs in a single location.
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240214131827.2856277-16-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
In order to reduce the number of lookups that we have to perform
when handling a sysreg, register each AArch64 sysreg descriptor
with the global xarray. The index of the descriptor is stored
as a 10 bit field in the data word.
Subsequent patches will retrieve and use the stored index.
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240214131827.2856277-15-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
As we are going to rely more and more on the global xarray that
contains the trap configuration, always populate it, even in the
non-NV case.
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240214131827.2856277-14-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
As NV results in a bunch of system instructions being trapped, it makes
sense to pull the system instructions into their own little array, where
they will eventually be joined by AT, TLBI and a bunch of other CMOs.
Based on an initial patch by Jintack Lim.
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240214131827.2856277-13-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Now that we don't use xa_store_range() anymore, drop the added
complexity of XARRAY_MULTI for KVM. It is likely still pulled
in by other bits of the kernel though.
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240214131827.2856277-12-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
In order to be able to store different values for member of an
encoding range, replace xa_store_range() calls with discrete
xa_store() calls and an encoding iterator.
We end-up using a bit more memory, but we gain some flexibility
that we will make use of shortly.
Take this opportunity to tidy up the error handling path.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Link: https://lore.kernel.org/r/20240214131827.2856277-11-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Negative trap bits are a massive pain. They are, on the surface,
indistinguishable from RES0 bits. Do you trap? or do you ignore?
Thankfully, we now have the right infrastructure to check for RES0
bits as long as the register is backed by VNCR, which is the case
for the FGT registers.
Use that information as a discriminant when handling a trap that
is potentially caused by a FGT.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240214131827.2856277-10-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
There is no reason to have separate FGT group identifiers for
the debug fine grain trapping. The sole requirement is to provide
the *names* so that the SR_FGF() macro can do its magic of picking
the correct bit definition.
So let's alias HDFGWTR_GROUP and HDFGRTR_GROUP.
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240214131827.2856277-9-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Now that we have the infrastructure to enforce a sanitised register
value depending on the VM configuration, drop the helper that only
used the architectural RES0 value.
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240214131827.2856277-8-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Just like its little friends, HCRX_EL2 gets the feature set treatment
when backed by VNCR.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240214131827.2856277-7-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Fine Grained Traps are controlled by a whole bunch of features.
Each one of them must be checked and the corresponding masks
computed so that we don't let the guest apply traps it shouldn't
be using.
This takes care of HFG[IRW]TR_EL2, HDFG[RW]TR_EL2, and HAFGRTR_EL2.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Link: https://lore.kernel.org/r/20240214131827.2856277-6-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
We can now start making use of our sanitising masks by setting them
to values that depend on the guest's configuration.
First up are VTTBR_EL2, VTCR_EL2, VMPIDR_EL2 and HCR_EL2.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240214131827.2856277-5-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
VNCR-backed "registers" are actually only memory. Which means that
there is zero control over what the guest can write, and that it
is the hypervisor's job to actually sanitise the content of the
backing store. Yeah, this is fun.
In order to preserve some form of sanity, add a repainting mechanism
that makes use of a per-VM set of RES0/RES1 masks, one pair per VNCR
register. These masks get applied on access to the backing store via
__vcpu_sys_reg(), ensuring that the state that is consumed by KVM is
correct.
So far, nothing populates these masks, but stay tuned.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Link: https://lore.kernel.org/r/20240214131827.2856277-4-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
In order to make it easier to check whether a particular feature
is exposed to a guest, add a new set of helpers, with kvm_has_feat()
being the most useful.
Let's start making use of them in the PMU code (courtesy of Oliver).
Follow-up changes will introduce additional use patterns.
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Co-developed--by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240214131827.2856277-3-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Despite having the control bits for FEAT_SPECRES and FEAT_PACM,
the ID registers fields are either incomplete or missing.
Fix it.
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20240214131827.2856277-2-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Open-coding the feature matching parameters for LVA/LVA2 leads to
issues with upcoming changes to the cpufeature code.
By making TGRAN{4,16,64} and VARange signed/unsigned as per the
architecture, we can use the existing macros, making the feature
match robust against those changes.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When set_pud() is called on a 4-level paging build config that runs with
3 levels at runtime (which happens with 16k page size builds with
support for LPA2), the updated entry is in fact a PGD in
swapper_pg_dir[], and this is mapped read-only after boot.
So in this case, the existing check needs to be performed as well, even
though __PAGETABLE_PUD_FOLDED is not #define'd. So replace the #ifdef
with a call to pgtable_l4_enabled().
Cc: Will Deacon <will@kernel.org>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20240216235944.3677178-2-ardb+git@google.com
Reviewed-by: Itaru Kitayama <itaru.kitayama@fujitsu.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This adds common1 register space for AM62A SoC which is using TI's Keystone
display hardware and supporting it as described in
Documentation/devicetree/bindings/display/ti/ti,am65x-dss.yaml
Fixes: 3618811657 ("arm64: dts: ti: k3-am62a-main: Add node for Display SubSystem (DSS)")
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://lore.kernel.org/r/20240216062426.4170528-5-devarsht@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
This adds common1 register space for AM62x SoC which is using TI's Keystone
display hardware and supporting it as described in
Documentation/devicetree/bindings/display/ti/ti,am65x-dss.yaml
Fixes: 8ccc1073c7 ("arm64: dts: ti: k3-am62-main: Add node for DSS")
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://lore.kernel.org/r/20240216062426.4170528-4-devarsht@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
This adds common1 register space for AM65x SoC which is using TI's Keystone
display hardware and supporting it as described in
Documentation/devicetree/bindings/display/ti/ti,am65x-dss.yaml
Fixes: fc539b90ed ("arm64: dts: ti: am654: Add DSS node")
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://lore.kernel.org/r/20240216062426.4170528-3-devarsht@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The external output reset signal was originally disabled and sent from
firmware. However, an unfixed bug in the firmware on tomato prevents
the signal from being sent, causing the device to fail to boot. To fix
this, enable external output reset signal to allow the device to reboot
normally.
Fixes: 5eb2e303ec ("arm64: dts: mediatek: Introduce MT8195 Cherry platform's Tomato")
Signed-off-by: Hsin-Te Yuan <yuanhsinte@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240124-send-upstream-v3-1-5097c9862a73@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
On MediaTek MT7986b RFB and MediaTek MT7986a RFB, port 5 of the MT7531
switch is connected to the second MAC of the SoC as a CPU port. Add the
port and set up the second MAC on the bindings.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20240219-for-mediatek-v1-2-7078f23eab82@arinc9.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
On Banana Pi BPI-R64 and MediaTek MT7622 RFB1 board, port 5 of the MT7531
switch is connected to the second MAC of the SoC as a CPU port. Add the
port and set up the second MAC on the bindings.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20240219-for-mediatek-v1-1-7078f23eab82@arinc9.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
The fbx8am boards are based on the Amlogic Meson G12A S905X2 SoC,
and the SEI510 board design.
Signed-off-by: Pierre-Hugues Husson <phhusson@freebox.fr>
Signed-off-by: Marc Gonzalez <mgonzalez@freebox.fr>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/59ca7d9a-a8dd-4062-852e-18b80ace6d7e@freebox.fr
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Underscores should not be used in node names (dtc with W=2 warns about
them), so replace them with hyphens.
Cc: Marc Gonzalez <mgonzalez@freebox.fr>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240213143217.336341-1-krzysztof.kozlowski@linaro.org
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
The am642-evm doesn't allow to enable 2 x CPSW3g ports and 2 x ICSSG1 ports
all together, so base k3-am642-evm.dts enables by default 2 x CPSW3g ports
and 1 x ICSSG1 ports, but it is also possible to support 1 x CPSW3g ports
and 2 x ICSSG1 ports configuration.
This patch adds overlay to support 1 x CPSW3g ports and 2 x ICSSG1 ports
configuration:
- Add label name 'mdio_mux_1' for 'mdio-mux-1' node so that the node
'mdio-mux-1' can be disabled in the overlay using the label name.
- disable 2nd CPSW3g port
- update CPSW3g pinmuxes to not use RGMII2
- disable mdio-mux-1 and define mdio-mux-2 to route ICSSG1 MDIO to the
shared DP83869 PHY
- add and enable ICSSG1 RGMII2 pinmuxes
- enable ICSSG1 MII1 port
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Link: https://lore.kernel.org/r/20240215103036.2825096-4-danishanwar@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
ICSSG1 provides dual Gigabit Ethernet support with proper FW loaded.
The ICSSG1 MII0 (RGMII1) has DP83869 PHY attached to it. The ICSSG1 shares
MII1 (RGMII2) PHY DP83869 with CPSW3g and it's assigned by default to
CPSW3g. The MDIO access to MII1 (RGMII2) PHY DP83869 is controlled by MDIO
bus switch and also assigned to CPSW3g. Therefore the ICSSG1 MII1 (RGMII2)
port is kept disable and ICSSG1 is enabled in single MAC mode by
default.
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Link: https://lore.kernel.org/r/20240215103036.2825096-3-danishanwar@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The ICSSG IP on AM64x SoCs have two Industrial Ethernet Peripherals (IEPs)
to manage/generate Industrial Ethernet functions such as time stamping.
Each IEP sub-module is sourced from an internal clock mux that can be
derived from either of the IP instance's ICSSG_IEP_GCLK or from another
internal ICSSG CORE_CLK mux. Add both the IEP nodes for both the ICSSG
instances. The IEP clock is currently configured to be derived
indirectly from the ICSSG_ICLK running at 250 MHz.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Link: https://lore.kernel.org/r/20240215103036.2825096-2-danishanwar@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Move bus-width property to *main.dtsi, above the OTAP/ITAP
delay values. While there is no error with where it is
currently at, it is easier to read the MMC node if the
bus-width property is located above the OTAP/ITAP delay
values consistently across MMC nodes.
Add missing bus-width for MMC2 in k3-am62-main.
Signed-off-by: Judith Mendez <jm@ti.com>
Tested-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240213235701.2438513-9-jm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Move ti,clkbuf-sel property above the OTAP/ITAP delay values.
While there is no error with where it is currently at, it is
easier to read the MMC node if ti,clkbuf-sel is located above
the OTAP/ITAP delay values consistently across MMC nodes.
Add missing ti,clkbuf-sel for MMC0 in k3-am64-main.
Signed-off-by: Judith Mendez <jm@ti.com>
Tested-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240213235701.2438513-8-jm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Remove DLL properties which are not applicable for soft PHYs
since these PHYs do not have a DLL to enable.
Acked-by: Francesco Dolcini <francesco.dolcini@toradex.com> # Verdin AM62
Signed-off-by: Judith Mendez <jm@ti.com>
Tested-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240213235701.2438513-7-jm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add OTAP/ITAP values to enable HS400 timing for MMC0 and
SDR104 timing for MMC1/MMC2. Remove no-1-8-v property to
enable the highest speed mode possible.
Update MMC OTAP/ITAP values according to the datasheet
[0], refer to Table 7-79 for MMC0 and Table 7-97 for MMC1/MMC2.
[0] https://www.ti.com/lit/ds/symlink/am62p.pdf
Signed-off-by: Judith Mendez <jm@ti.com>
Link: https://lore.kernel.org/r/20240213235701.2438513-6-jm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add support for 32GB eMMC card on AM62A7 SK. Includes adding mmc0
pins settings. Add mmc0 alias for sdhci0 in k3-am62a7-sk.dts.
Signed-off-by: Nitin Yadav <n-yadav@ti.com>
Signed-off-by: Judith Mendez <jm@ti.com>
Link: https://lore.kernel.org/r/20240213235701.2438513-4-jm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
"msi-map-mask" is a required property for all Qcom PCIe controllers as it
would allow all PCIe devices under a bus to share the same MSI identifier.
Without this property, each device has to use a separate MSI identifier
which is not possible due to platform limitations.
Currently, this is not an issue since only one device is connected to the
bus on boards making use of this SoC.
Fixes: a33a532b3b ("arm64: dts: qcom: sm8650: Use GIC-ITS for PCIe0 and PCIe1")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240216-sm8550-msi-map-fix-v1-1-b66d83ce48b7@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Underscores should not be used in node names (dtc with W=2 warns about
them), so replace them with hyphens.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20240213145124.342514-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Only Tx and Rx Signal lines for wkup_uart0 are brought out on
the J784S4 EVM from SoC, but CTS and RTS signal lines are not
brought on the EVM. Thus, remove pinmux for CTS and RTS signal
lines for wkup_uart0 in J784S4.
Fixes: 6fa5d37a2f ("arm64: dts: ti: k3-j784s4-evm: Add mcu and wakeup uarts")
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Link: https://lore.kernel.org/r/20240214105846.1096733-5-b-kapoor@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Only Tx and Rx Signal lines for wkup_uart0 are brought out on
the Common Proc Board through SoM, but CTS and RTS signal lines
are not brought on the board. Thus, remove pinmux for CTS and RTS
signal lines for wkup_uart0 in J721S2.
Fixes: f5e9ee0b35 ("arm64: dts: ti: k3-j721s2-common-proc-board: Add uart pinmux")
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Link: https://lore.kernel.org/r/20240214105846.1096733-4-b-kapoor@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
RPi v2 Camera (IMX219) is an 8MP camera that can be used with SK-AM69,
J721E SK, and AM68 SK through the 22-pin CSI-RX connector.
Add a reference overlay for dual IMX219 RPI camera v2 modules
which can be used across AM68 SK, AM69 SK, TDA4VM SK boards
that have a 15/22-pin FFC connector. Also enable build testing
and symbols for all the three platforms.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Reviewed-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240215085518.552692-10-vaishnav.a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
J784S4 has three CSI2RX capture subsystem featuring Cadence CSI2RX,
DPHY and TI's pixel grabbing wrapper. Add nodes for the same and
keep them disabled by default. J784S4 uses a dedicated BCDMA instance
for CSI-RX traffic, so enable that as well.
J784S4 TRM (Section 12.7 Camera Subsystem):
https://www.ti.com/lit/zip/spruj52
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Reviewed-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240215085518.552692-9-vaishnav.a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
J721S2 has two CSI2RX capture subsystem featuring Cadence CSI2RX,
DPHY and TI's pixel grabbing wrapper. Add nodes for the same and
keep them disabled by default. J721S2 uses a dedicated BCDMA instance
for CSI-RX traffic, so enable that as well.
J721S2 TRM (Section 12.7 Camera Subsystem):
https://www.ti.com/lit/zip/spruj28
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Reviewed-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240215085518.552692-8-vaishnav.a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
J721E has two CSI2RX capture subsystem featuring Cadence CSI2RX,
DPHY and TI's pixel grabbing wrapper. Add nodes for the same and
keep them disabled by default.
J721E TRM (Section 12.7 Camera Subsystem):
https://www.ti.com/lit/zip/spruil1
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Reviewed-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240215085518.552692-7-vaishnav.a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
J721E SK has the CSI2RX routed to a MIPI CSI connector and to 15-pin
RPi camera connector through an analog mux with GPIO control, model that
so that an overlay can control the mux state according to connected
cameras. Also provide labels to the I2C mux bus instances so that a
generic overlay can be used across multiple platforms.
J721E SK schematics: https://www.ti.com/lit/zip/sprr438
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Reviewed-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240215085518.552692-6-vaishnav.a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
CSI cameras are controlled using I2C. On AM69 Starter Kit, this is routed
to I2C-1, so enable the instance, TCA9543 I2C switch and the TCA6408
GPIO expander on the bus. AM69 SK has the CSI2RX routed to a MIPI CSI
connector and to 22-pin RPi camera connector through an analog mux with
GPIO control, model that so that an overlay can control the mux state
according to connected cameras.
AM69 SK schematics: https://www.ti.com/lit/zip/sprr466
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Reviewed-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240215085518.552692-5-vaishnav.a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
CSI cameras are controlled using I2C. On AM68 Starter Kit, this is routed
to I2C-1, so enable the instance and the TCA9543 I2C switch on the bus.
AM68 SK schematics: https://www.ti.com/lit/zip/sprr463
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Reviewed-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240215085518.552692-4-vaishnav.a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
CSI cameras are controlled using I2C. On J784S4 EVM, this is routed
to I2C-5, so enable the instance and the TCA6408 GPIO expander
on the bus.
J784S4 EVM schematics: https://www.ti.com/lit/zip/sprr458
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Reviewed-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240215085518.552692-3-vaishnav.a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Via the PMIC GLINK driver we can get info about fuel gauge, charger and
USB connector events. Add the node to the dts and configure USB so that
role switching works.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20231220-fp5-pmic-glink-v1-3-2a1f8e3c661c@fairphone.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a reserved memory for the TI AM65X platform watchdog
to reserve the specific info, triggering the watchdog reset in last
boot, to know if the board reboot is due to a watchdog reset.
Signed-off-by: Li Hua Qian <huaqian.li@siemens.com>
Link: https://lore.kernel.org/r/20240117060654.109424-1-huaqian.li@siemens.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
pcie2a and pcie3a both cause interrupt storms to occur. However, when
both are enabled simultaneously, the two combined interrupt storms will
lead to rcu stalls. Red Hat is the only company still using this board
and since we still need pcie3a, just disable pcie2a.
Signed-off-by: Lucas Karpinski <lkarpins@redhat.com>
Reviewed-by: Brian Masney <bmasney@redhat.com>
Link: https://lore.kernel.org/r/qcoqksikfvdqxk6stezbzc7l2br37ccgqswztzqejmhrkhbrwt@ta4npsm35mqk
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The "capacity-dmips-mhz" and "dynamic-power-coefficient" are
used to build Energy Model which in turn is used by EAS to take
placement decisions. So add it to SC7280 soc.
Signed-off-by: Ankit Sharma <quic_anshar@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20231103105440.23904-1-quic_anshar@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
* Avoid dropping the page refcount twice when freeing an unlinked
page-table subtree.
* Don't source the VFIO Kconfig twice
* Fix protected-mode locking order between kvm and vcpus
RISC-V:
* Fix steal-time related sparse warnings
x86:
* Cleanup gtod_is_based_on_tsc() to return "bool" instead of an "int"
* Make a KVM_REQ_NMI request while handling KVM_SET_VCPU_EVENTS if and only
if the incoming events->nmi.pending is non-zero. If the target vCPU is in
the UNITIALIZED state, the spurious request will result in KVM exiting to
userspace, which in turn causes QEMU to constantly acquire and release
QEMU's global mutex, to the point where the BSP is unable to make forward
progress.
* Fix a type (u8 versus u64) goof that results in pmu->fixed_ctr_ctrl being
incorrectly truncated, and ultimately causes KVM to think a fixed counter
has already been disabled (KVM thinks the old value is '0').
* Fix a stack leak in KVM_GET_MSRS where a failed MSR read from userspace
that is ultimately ignored due to ignore_msrs=true doesn't zero the output
as intended.
Selftests cleanups and fixes:
* Remove redundant newlines from error messages.
* Delete an unused variable in the AMX test (which causes build failures when
compiling with -Werror).
* Fail instead of skipping tests if open(), e.g. of /dev/kvm, fails with an
error code other than ENOENT (a Hyper-V selftest bug resulted in an EMFILE,
and the test eventually got skipped).
* Fix TSC related bugs in several Hyper-V selftests.
* Fix a bug in the dirty ring logging test where a sem_post() could be left
pending across multiple runs, resulting in incorrect synchronization between
the main thread and the vCPU worker thread.
* Relax the dirty log split test's assertions on 4KiB mappings to fix false
positives due to the number of mappings for memslot 0 (used for code and
data that is NOT being dirty logged) changing, e.g. due to NUMA balancing.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmXPlokUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroPs3AgApdYANmMEy2YaUZLYsQOEP388vLEf
+CS9kChY6xWuYzdFPTpM4BqNVn46zPh+HDEHTCJy1eOLpeOg6HbaNGuF/1G98+HF
COm7C2bWOrGAL/UMzPzciyEMQFE7c/h28Yuq/4XpyDNrFbnChYxPh9W4xexqoLhV
QtGYU03guLCUsI5veY0rOrSJ5xEu9f8c63JH5JPahtbMB0uNoi0Kz7i86sbkkUg7
OcTra+j/FyGVAWwEJ8Q2hcGlKn4DMeyQ/riUvPrfSarTqC6ZswKltg9EMSxNnojE
LojijqRFjKklkXonnalVeDzJbG0OWHks8VO6JmCJdt0zwBRei0iLWi2LEg==
=8/la
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"ARM:
- Avoid dropping the page refcount twice when freeing an unlinked
page-table subtree.
- Don't source the VFIO Kconfig twice
- Fix protected-mode locking order between kvm and vcpus
RISC-V:
- Fix steal-time related sparse warnings
x86:
- Cleanup gtod_is_based_on_tsc() to return "bool" instead of an "int"
- Make a KVM_REQ_NMI request while handling KVM_SET_VCPU_EVENTS if
and only if the incoming events->nmi.pending is non-zero. If the
target vCPU is in the UNITIALIZED state, the spurious request will
result in KVM exiting to userspace, which in turn causes QEMU to
constantly acquire and release QEMU's global mutex, to the point
where the BSP is unable to make forward progress.
- Fix a type (u8 versus u64) goof that results in pmu->fixed_ctr_ctrl
being incorrectly truncated, and ultimately causes KVM to think a
fixed counter has already been disabled (KVM thinks the old value
is '0').
- Fix a stack leak in KVM_GET_MSRS where a failed MSR read from
userspace that is ultimately ignored due to ignore_msrs=true
doesn't zero the output as intended.
Selftests cleanups and fixes:
- Remove redundant newlines from error messages.
- Delete an unused variable in the AMX test (which causes build
failures when compiling with -Werror).
- Fail instead of skipping tests if open(), e.g. of /dev/kvm, fails
with an error code other than ENOENT (a Hyper-V selftest bug
resulted in an EMFILE, and the test eventually got skipped).
- Fix TSC related bugs in several Hyper-V selftests.
- Fix a bug in the dirty ring logging test where a sem_post() could
be left pending across multiple runs, resulting in incorrect
synchronization between the main thread and the vCPU worker thread.
- Relax the dirty log split test's assertions on 4KiB mappings to fix
false positives due to the number of mappings for memslot 0 (used
for code and data that is NOT being dirty logged) changing, e.g.
due to NUMA balancing"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (25 commits)
KVM: arm64: Fix double-free following kvm_pgtable_stage2_free_unlinked()
RISC-V: KVM: Use correct restricted types
RISC-V: paravirt: Use correct restricted types
RISC-V: paravirt: steal_time should be static
KVM: selftests: Don't assert on exact number of 4KiB in dirty log split test
KVM: selftests: Fix a semaphore imbalance in the dirty ring logging test
KVM: x86: Fix KVM_GET_MSRS stack info leak
KVM: arm64: Do not source virt/lib/Kconfig twice
KVM: x86/pmu: Fix type length error when reading pmu->fixed_ctr_ctrl
KVM: x86: Make gtod_is_based_on_tsc() return 'bool'
KVM: selftests: Make hyperv_clock require TSC based system clocksource
KVM: selftests: Run clocksource dependent tests with hyperv_clocksource_tsc_page too
KVM: selftests: Use generic sys_clocksource_is_tsc() in vmx_nested_tsc_scaling_test
KVM: selftests: Generalize check_clocksource() from kvm_clock_test
KVM: x86: make KVM_REQ_NMI request iff NMI pending for vcpu
KVM: arm64: Fix circular locking dependency
KVM: selftests: Fail tests when open() fails with !ENOENT
KVM: selftests: Avoid infinite loop in hyperv_features when invtsc is missing
KVM: selftests: Delete superfluous, unused "stage" variable in AMX test
KVM: selftests: x86_64: Remove redundant newlines
...
- Fix allocation failure during SVE coredumps
- Fix handling of SVE context on signal delivery
- Enable Neoverse N2 CPU errata workarounds for Microsoft's
"Azure Cobalt 100" clone
- Work around CMN PMU erratum in AmpereOneX implementation
- Fix typo in CXL PMU event definition
- Fix jump label asm constraints
-----BEGIN PGP SIGNATURE-----
iQFEBAABCgAuFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAmXPNJ0QHHdpbGxAa2Vy
bmVsLm9yZwAKCRC3rHDchMFjNExZCADHk1V3rt7a/00GPG392Z8wS+r/4K6pPhNs
F+ZUS/ls7+oTSHKU7IcdRfSIpeYnjkwzS2twCusrphqCQwQEFcqB9t7GeiNVkNBZ
3TeYgERwlzhOstJtjMPAJSfRjkUfqpxsm+AbwgdiGxVonOrOtxSPXtc5N8QrhiH5
RwvqYkQpEd6Cq3kmKifEQxs6WPUGLhDlHTPOGC/HcM7DtaU6CKfZk4+LjZxNm8S8
onZwVumhQOXzpfrIQabbgZ6tsKTrsysj6RVoMG9Q4u1vESyGIk2+3zRx3kI9n9ao
3/tvjCg/UY6UfTggruB58cW4+ImT1jXAhLBG3wbGS7A5t8giJ8zl
=iRRM
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"It's a little busier than normal, but it's still not a lot of code and
things seem fairly quiet in general:
- Fix allocation failure during SVE coredumps
- Fix handling of SVE context on signal delivery
- Enable Neoverse N2 CPU errata workarounds for Microsoft's "Azure
Cobalt 100" clone
- Work around CMN PMU erratum in AmpereOneX implementation
- Fix typo in CXL PMU event definition
- Fix jump label asm constraints"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64/sve: Lower the maximum allocation for the SVE ptrace regset
arm64: Subscribe Microsoft Azure Cobalt 100 to ARM Neoverse N2 errata
perf/arm-cmn: Workaround AmpereOneX errata AC04_MESH_1 (incorrect child count)
arm64: jump_label: use constraints "Si" instead of "i"
arm64: fix typo in comments
perf: CXL: fix mismatched cpmu event opcode
arm64/signal: Don't assume that TIF_SVE means we saved SVE state
Bindings allow a "wake", not "enable", GPIO. Schematics also use WAKE
name for the pin:
sa8155p-adp.dtb: pcie@1c00000: Unevaluated properties are not allowed ('enable-gpio' was unexpected)
Fixes: a1c86c6805 ("arm64: dts: qcom: sm8150: Add PCIe nodes")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240108131216.53867-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Bindings allow a "wake", not "enable", GPIO. Schematics also use WAKE
name for the pin:
sdm845-db845c.dtb: pcie@1c00000: Unevaluated properties are not allowed ('enable-gpio' was unexpected)
Fixes: 4a657c264b ("arm64: dts: qcom: db845c: Enable PCIe controllers")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240108131216.53867-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the description for the display panel found on this phone.
Unfortunately the LCDB module on PM6150L isn't yet supported upstream so
we need to use a dummy regulator-fixed in the meantime.
And with this done we can also enable the GPU and set the zap shader
firmware path.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20240216-fp4-panel-v3-4-a556e4b79640@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The GMU won't probe without GPU being enabled, so we can remove the
disabled status so we don't have to explicitly enable the GMU in all the
devices that enable GPU.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20240216-fp4-panel-v3-3-a556e4b79640@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Like the Samsung Galaxy A3/A5, the Grand Prime/Core Prime uses a
Richtek RT5033 PMIC as battery fuel gauge, charger, flash LED and for some
regulators.
For now, only add the fuel gauge/battery device to the device tree, so we
can check the remaining battery percentage.
The other RT5033 drivers need some more work first before they can be used
properly.
Signed-off-by: Joe Mason <buddyjojo06@outlook.com>
[Raymond: Move to fortuna-common. Use interrupts-extended]
Signed-off-by: Raymond Hackley <raymondhackley@protonmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240216124639.24689-1-raymondhackley@protonmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
- Avoid dropping the page refcount twice when freeing an unlinked
page-table subtree.
-----BEGIN PGP SIGNATURE-----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=Coky
-----END PGP SIGNATURE-----
Merge tag 'kvmarm-fixes-6.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm64 fixes for 6.8, take #2
- Avoid dropping the page refcount twice when freeing an unlinked
page-table subtree.
- Don't source the VFIO Kconfig twice
- Fix protected-mode locking order between kvm and vcpus
-----BEGIN PGP SIGNATURE-----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=wb0z
-----END PGP SIGNATURE-----
Merge tag 'kvmarm-fixes-6.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm64 fixes for 6.8, take #1
- Don't source the VFIO Kconfig twice
- Fix protected-mode locking order between kvm and vcpus
The AArch64 virtual memory system supports a global WXN control, which
can be enabled to make all writable mappings implicitly no-exec. This is
a useful hardening feature, as it prevents mistakes in managing page
table permissions from being exploited to attack the system.
When enabled at EL1, the restrictions apply to both EL1 and EL0. EL1 is
completely under our control, and has been cleaned up to allow WXN to be
enabled from boot onwards. EL0 is not under our control, but given that
widely deployed security features such as selinux or PaX already limit
the ability of user space to create mappings that are writable and
executable at the same time, the impact of enabling this for EL0 is
expected to be limited. (For this reason, common user space libraries
that have a legitimate need for manipulating executable code already
carry fallbacks such as [0].)
If enabled at compile time, the feature can still be disabled at boot if
needed, by passing arm64.nowxn on the kernel command line.
[0] https://github.com/libffi/libffi/blob/master/src/closures.c#L440
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20240214122845.2033971-88-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
We typically enable support in defconfig for all architectural features
for which we can detect at runtime if the hardware actually supports
them.
Now that we have implemented support for LPA2 based 52-bit virtual
addressing in a way that should not impact 48-bit operation on non-LPA2
CPU, we can do the same, and enable 52-bit virtual addressing by
default.
Catalin adds:
Currently the "Virtual address space size" arch/arm64/Kconfig menu
entry sets different defaults for each page size. However, all are
overridden by the defconfig to 48 bits. Set the new default in
Kconfig and remove the defconfig line.
[ardb: squash follow-up fix from Catalin]
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20240214122845.2033971-86-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Update Kconfig to permit 4k and 16k granule configurations to be built
with 52-bit virtual addressing, now that all the prerequisites are in
place.
While at it, update the feature description so it matches on the
appropriate feature bits depending on the page size. For simplicity,
let's just keep ARM64_HAS_VA52 as the feature name.
Note that LPA2 based 52-bit virtual addressing requires 52-bit physical
addressing support to be enabled as well, as programming TCR.TxSZ to
values below 16 is not allowed unless TCR.DS is set, which is what
activates the 52-bit physical addressing support.
While supporting the converse (52-bit physical addressing without 52-bit
virtual addressing) would be possible in principle, let's keep things
simple, by only allowing these features to be enabled at the same time.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20240214122845.2033971-85-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
get_user_mapping_size() uses vabits_actual and CONFIG_PGTABLE_LEVELS to
provide the starting point for a table walk. This is fine for LVA, as
the number of translation levels is the same regardless of whether LVA
is enabled. However, with LPA2, this will no longer be the case, so
let's derive the number of levels from the number of VA bits directly.
Acked-by: Marc Zyngier <maz@kernel.org>
Acked-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20240214122845.2033971-84-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Currently, the ptdump code deals with folded PMD or PUD levels at build
time, by omitting those levels when invoking note_page. IOW, note_page()
is never invoked with level == 1 if P4Ds are folded in the build
configuration.
With the introduction of LPA2 support, we will defer some of these
folding decisions to runtime, so let's take care of this by overriding
the 'level' argument when this condition triggers.
Substituting the PUD or PMD strings for "PGD" when the level in question
is folded at build time is no longer necessary, and so the conditional
expressions can be simplified. This also makes the indirection of the
'name' field unnecessary, so change that into a char[] array, and make
the whole thing __ro_after_init.
Note that the mm_p?d_folded() functions currently ignore their mm
pointer arguments, but let's wire them up correctly anyway.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20240214122845.2033971-83-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Configurations built with support for 52-bit virtual addressing can also
run on CPUs that only support 48 bits of VA space, in which case only
that part of swapper_pg_dir that represents the 48-bit addressable
region is relevant, and everything else is ignored by the hardware.
Our software pagetable walker has little in the way of input address
validation, and so it will happily start a walk from an address that is
not representable by the number of paging levels that are actually
active, resulting in lots of bogus output from the page table dumper
unless we take care to start at a valid address.
So define the start address at runtime based on vabits_actual.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20240214122845.2033971-82-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In order to support LPA2 on 16k pages in a way that permits non-LPA2
systems to run the same kernel image, we have to be able to fall back to
at most 48 bits of virtual addressing.
Falling back to 48 bits would result in a level 0 with only 2 entries,
which is suboptimal in terms of TLB utilization. So instead, let's fall
back to 47 bits in that case. This means we need to be able to fold PUDs
dynamically, similar to how we fold P4Ds for 48 bit virtual addressing
on LPA2 with 4k pages.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20240214122845.2033971-81-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Allow the KASAN init code to deal with 5 levels of paging, and relax the
requirement that the shadow region is aligned to the top level pgd_t
size. This is necessary for LPA2 based 52-bit virtual addressing, where
the KASAN shadow will never be aligned to the pgd_t size. Allowing this
also enables the 16k/48-bit case for KASAN, which is a nice bonus.
This involves some hackery to manipulate the root and next level page
tables without having to distinguish all the various configurations,
including 16k/48-bits (which has a two entry pgd_t level), and LPA2
configurations running with one translation level less on non-LPA2
hardware.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20240214122845.2033971-80-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add support for using 5 levels of paging in the fixmap, as well as in
the kernel page table handling code which uses fixmaps internally.
This also handles the case where a 5 level build runs on hardware that
only supports 4 levels of paging.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20240214122845.2033971-79-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Update the early kernel mapping code to take 52-bit virtual addressing
into account based on the LPA2 feature. This is a bit more involved than
LVA (which is supported with 64k pages only), given that some page table
descriptor bits change meaning in this case.
To keep the handling in asm to a minimum, the initial ID map is still
created with 48-bit virtual addressing, which implies that the kernel
image must be loaded into 48-bit addressable physical memory. This is
currently required by the boot protocol, even though we happen to
support placement outside of that for LVA/64k based configurations.
Enabling LPA2 involves more than setting TCR.T1SZ to a lower value,
there is also a DS bit in TCR that needs to be set, and which changes
the meaning of bits [9:8] in all page table descriptors. Since we cannot
enable DS and every live page table descriptor at the same time, let's
pivot through another temporary mapping. This avoids the need to
reintroduce manipulations of the page tables with the MMU and caches
disabled.
To permit the LPA2 feature to be overridden on the kernel command line,
which may be necessary to work around silicon errata, or to deal with
mismatched features on heterogeneous SoC designs, test for CPU feature
overrides first, and only then enable LPA2.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20240214122845.2033971-78-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add support for 5 level paging in the G-to-nG routine that creates its
own temporary page tables to traverse the swapper page tables. Also add
support for running the 5 level configuration with the top level folded
at runtime, to support CPUs that do not implement the LPA2 extension.
While at it, wire up the level skipping logic so it will also trigger on
4 level configurations with LPA2 enabled at build time but not active at
runtime, as we'll fall back to 3 level paging in that case.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20240214122845.2033971-77-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add the required types and descriptor accessors to support 5 levels of
paging in the common code. This is one of the prerequisites for
supporting 52-bit virtual addressing with 4k pages.
Note that this does not cover the code that handles kernel mappings or
the fixmap.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20240214122845.2033971-76-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In preparation for enabling LPA2 support, introduce the mask values for
converting between physical addresses and their representations in a
page table descriptor.
While at it, move the pte_to_phys asm macro into its only user, so that
we can freely modify it to use its input value register as a temp
register.
For LPA2, the PTE_ADDR_MASK contains two non-adjacent sequences of zero
bits, which means it no longer fits into the immediate field of an
ordinary ALU instruction. So let's redefine it to include the bits in
between as well, and only use it when converting from physical address
to PTE representation, where the distinction does not matter. Also
update the name accordingly to emphasize this.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20240214122845.2033971-75-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When LPA2 is enabled, bits 8 and 9 of page and block descriptors become
part of the output address instead of carrying shareability attributes
for the region in question.
So avoid setting these bits if TCR.DS == 1, which means LPA2 is enabled.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20240214122845.2033971-74-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The LPA2 feature introduces new FSC values to report abort exceptions
related to translation level -1. Define these and wire them up.
Reuse the new ESR FSC classification helpers that arrived via the KVM
arm64 tree, and update the one for translation faults to check
specifically for a translation fault at level -1. (Access flag or
permission faults cannot occur at level -1 because they alway involve a
descriptor at the superior level so changing those helpers is not
needed).
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20240214122845.2033971-73-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The PROT_* macros resolve to expressions that are only valid in C and
not in assembler, and so they are only usable from C code. Currently, we
make an exception for the permission indirection init code in proc.S,
which doesn't care about the bits that are conditionally set, and so we
just #define PTE_MAYBE_NG to 0x0 for any assembler file that includes
these definitions.
This is dodgy because this means that PROT_NORMAL and friends is
generally available in asm code, but defined in a way that deviates from
the definition that C code will observe, which might lead to hard to
diagnose issues down the road.
So instead, #define PTE_MAYBE_NG only in the place where the PIE
constants are evaluated, and #undef it again right after. This allows us
to drop the #define from pgtable-prot.h, and avoid the risk of deviating
definitions between asm and C.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20240214122845.2033971-72-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add support for overriding the VARange field of the MMFR2 CPU ID
register. This permits the associated LVA feature to be overridden early
enough for the boot code that creates the kernel mapping to take it into
account.
Given that LPA2 implies LVA, disabling the latter should disable the
former as well. So override the ID_AA64MMFR0.TGran field of the current
page size as well if it advertises support for 52-bit addressing.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20240214122845.2033971-71-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Currently, we detect CPU support for 52-bit virtual addressing (LVA)
extremely early, before creating the kernel page tables or enabling the
MMU. We cannot override the feature this early, and so large virtual
addressing is always enabled on CPUs that implement support for it if
the software support for it was enabled at build time. It also means we
rely on non-trivial code in asm to deal with this feature.
Given that both the ID map and the TTBR1 mapping of the kernel image are
guaranteed to be 48-bit addressable, it is not actually necessary to
enable support this early, and instead, we can model it as a CPU
feature. That way, we can rely on code patching to get the correct
TCR.T1SZ values programmed on secondary boot and resume from suspend.
On the primary boot path, we simply enable the MMU with 48-bit virtual
addressing initially, and update TCR.T1SZ if LVA is supported from C
code, right before creating the kernel mapping. Given that TTBR1 still
points to reserved_pg_dir at this point, updating TCR.T1SZ should be
safe without the need for explicit TLB maintenance.
Since this gets rid of all accesses to the vabits_actual variable from
asm code that occurred before TCR.T1SZ had been programmed, we no longer
have a need for this variable, and we can replace it with a C expression
that produces the correct value directly, based on the value of TCR.T1SZ.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20240214122845.2033971-70-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This reverts commit 1682c45b92, which is no longer needed now that
we create the permanent kernel mapping directly during early boot.
This is a RINO (revert in name only) given that some of the code has
moved around, but the changes are straight-forward.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20240214122845.2033971-69-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Now that the early kernel mapping is created with all the right
attributes and segment boundaries, there is no longer a need to recreate
it and switch to it. This also means we no longer have to copy the kasan
shadow or some parts of the fixmap from one set of page tables to the
other.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20240214122845.2033971-68-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Early in the boot, when .rodata is still writable, we can poke
swapper_pg_dir entries directly, and there is no need to go through the
fixmap. After a future patch, we will enter the kernel with
swapper_pg_dir already active, and early swapper_pg_dir updates for
creating the fixmap page table hierarchy itself cannot go through the
fixmap for obvious reaons. So let's keep track of whether rodata is
writable, and update the descriptor directly in that case.
As the same reasoning applies to early KASAN init, make the function
noinstr as well.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20240214122845.2033971-67-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The asm code that creates the initial ID map is rather intricate and
hard to follow. This is problematic because it makes adding support for
things like LPA2 or WXN more difficult than necessary. Also, it is
parameterized like the rest of the MM code to run with a configurable
number of levels, which is rather pointless, given that all AArch64 CPUs
implement support for 48-bit virtual addressing, and that many systems
exist with DRAM located outside of the 39-bit addressable range, which
is the only smaller VA size that is widely used, and we need additional
tricks to make things work in that combination.
So let's bite the bullet, and rip out all the asm macros, and fiddly
code, and replace it with a C implementation based on the newly added
routines for creating the early kernel VA mappings. And while at it,
create the initial ID map based on 48-bit virtual addressing as well,
regardless of the number of configured levels for the kernel proper.
Note that this code may execute with the MMU and caches disabled, and is
therefore not permitted to make unaligned accesses. This shouldn't
generally happen in any case for the algorithm as implemented, but to be
sure, let's pass -mstrict-align to the compiler just in case.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20240214122845.2033971-66-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The mapping from PGD/PUD/PMD to levels and shifts is very confusing,
given that, due to folding, the shifts may be equal for different
levels, if the macros are even #define'd to begin with.
In a subsequent patch, we will modify the ID mapping code to decouple
the number of levels from the kernel's view of how these types are
folded, so prepare for this by reformulating the macros without the use
of these types.
Instead, use SWAPPER_BLOCK_SHIFT as the base quantity, and derive it
from either PAGE_SHIFT or PMD_SHIFT, which -if defined at all- are
defined unambiguously for a given page size, regardless of the number of
configured levels.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20240214122845.2033971-65-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Even though we support loading kernels anywhere in 48-bit addressable
physical memory, we create the ID maps based on the number of levels
that we happened to configure for the kernel VA and user VA spaces.
The reason for this is that the PGD/PUD/PMD based classification of
translation levels, along with the associated folding when the number of
levels is less than 5, does not permit creating a page table hierarchy
of a set number of levels. This means that, for instance, on 39-bit VA
kernels we need to configure an additional level above PGD level on the
fly, and 36-bit VA kernels still only support 47-bit virtual addressing
with this trick applied.
Now that we have a separate helper to populate page table hierarchies
that does not define the levels in terms of PUDS/PMDS/etc at all, let's
reuse it to create the permanent ID map with a fixed VA size of 48 bits.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20240214122845.2033971-64-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The asm version of the kernel mapping code works fine for creating a
coarse grained identity map, but for mapping the kernel down to its
exact boundaries with the right attributes, it is not suitable. This is
why we create a preliminary RWX kernel mapping first, and then rebuild
it from scratch later on.
So let's reimplement this in C, in a way that will make it unnecessary
to create the kernel page tables yet another time in paging_init().
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20240214122845.2033971-63-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
__cpu_replace_ttbr1() is a static inline, and so it gets instantiated
wherever it is used. This is not really necessary, as it is never called
on a hot path. It also has the unfortunate side effect that the symbol
idmap_cpu_replace_ttbr1 may never be referenced from kCFI enabled C
code, and this means the type id symbol may not exist either. This will
result in a build error once we start referring to this symbol from asm
code as well. (Note that this problem only occurs when CnP, KAsan and
suspend/resume are all disabled in the Kconfig but that is a valid
config, if unusual).
So let's just move it out of line so all callers will share the same
implementation, which will reference idmap_cpu_replace_ttbr1
unconditionally.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20240214122845.2033971-62-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In preparation for moving the first assignment of arm64_use_ng_mappings
to an earlier stage in the boot, ensure that kaslr_requires_kpti() is
accessible without relying on the core kernel's view on whether or not
KASLR is enabled. So make it a static inline, and move the
kaslr_enabled() check out of it and into the callers, one of which will
disappear in a subsequent patch.
Once/when support for the obsolete ThunderX 1 platform is dropped, this
check reduces to a E0PD feature check on the local CPU.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20240214122845.2033971-61-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Now that we can set BSS variables from the early code running from the
ID map, we can set memstart_offset_seed directly from the C code that
derives the value instead of passing it back and forth between C and asm
code.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20240214122845.2033971-60-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In preparation for switching to an early kernel mapping routine that
maps each segment according to its precise boundaries, and with the
correct attributes, let's allocate some extra pages for page tables for
the 4k page size configuration. This is necessary because the start and
end of each segment may not be aligned to the block size, and so we'll
need an extra page table at each segment boundary.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20240214122845.2033971-59-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add some helpers that will be used by the early kernel mapping code to
check feature support on the local CPU. This permits the early kernel
mapping to be created with the right attributes, removing the need for
tearing it down and recreating it.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20240214122845.2033971-58-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add rodata=off to the set of kernel command line options that is parsed
early using the CPU feature override detection code, so we can easily
refer to it when creating the kernel mapping.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20240214122845.2033971-57-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The early kaslr code open codes the detection of 'nokaslr' on the kernel
command line, and this is no longer necessary now that the feature
detection code, which also looks for the same string, executes before
this code.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20240214122845.2033971-56-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add some helpers to extract and apply feature overrides to the bare
idreg values. This involves inspecting the value and mask of the
specific field that we are interested in, given that an override
value/mask pair might be invalid for one field but valid for another.
Then, wire up the new helper for the hVHE test - note that we can drop
the sysreg test here, as the override will be invalid when trying to
enable hVHE on non-VHE capable hardware.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20240214122845.2033971-55-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Once we update the early kernel mapping code to only map the kernel once
with the right permissions, we can no longer perform code patching via
this mapping.
So move this code to an earlier stage of the boot, right after applying
the relocations.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20240214122845.2033971-54-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
To permit the feature overrides to be taken into account before the
KASLR init code runs and the kernel mapping is created, move the
detection code to an earlier stage in the boot.
In a subsequent patch, this will be taken advantage of by merging the
preliminary and permanent mappings of the kernel text and data into a
single one that gets created and relocated before start_kernel() is
called.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20240214122845.2033971-53-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In order to allow the CPU feature override detection code to run even
earlier, move the feature override global variables into BSS, which is
the only part of the static kernel image that is mapped read-write in
the initial ID map.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20240214122845.2033971-52-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
We will move the CPU feature overrides into BSS in a subsequent patch,
and this requires that BSS is zeroed before the feature override
detection code runs. So let's map BSS read-write in the ID map, and zero
it via this mapping.
Since the kernel page tables are right next to it, and also zeroed via
the ID map, let's drop the separate clear_page_tables() function, and
just zero everything in one go.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20240214122845.2033971-51-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
We will want to parse the ID register overrides even earlier, so that we
can take them into account before creating the kernel mapping. So
migrate the code and make it work in the context of the early C runtime.
We will move the invocation to an earlier stage in a subsequent patch.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20240214122845.2033971-49-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Now that we have a mini C runtime before the kernel mapping is up, we
can move the non-trivial relocation processing code out of head.S and
reimplement it in C.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20240214122845.2033971-48-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
We will add some code under pi/ that contains global variables that
should not end up in __initdata, as they will not be writable via the
initial ID map. So only rely on objcopy for making the libfdt code
__init, and use explicit annotations for the rest.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20240214122845.2033971-47-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The mini C runtime runs before relocations are processed, and so it
cannot rely on statically initialized pointer variables.
Add a check to ensure that such code does not get introduced by
accident, by going over the relocations in each object, identifying the
ones that operate on data sections that are part of the executable
image, and raising an error if any relocations of type R_AARCH64_ABS64
exist. Note that such relocations are permitted in other places (e.g.,
debug sections) and will never occur in compiler generated code sections
when using the small code model, so only check sections that have
SHF_ALLOC set and SHF_EXECINSTR cleared.
To accommodate cases where statically initialized symbol references are
unavoidable, introduce a special case for ELF input data sections that
have ".rodata.prel64" in their names, and in these cases, instead of
rejecting any encountered ABS64 relocations, convert them into PREL64
relocations, which don't require any runtime fixups. Note that the code
in question must still be modified to deal with this, as it needs to
convert the 64-bit signed offsets into absolute addresses before use.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20240214122845.2033971-46-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The cros_ec driver currently assumes that cros-ec-spi compatible device
nodes are a wakeup-source even though the wakeup-source property is not
defined.
Some Chromebooks use a separate wake pin, while others overload the
interrupt for wake and IO. With the current assumption, spurious wakes
can occur on systems that use a separate wake pin. It is planned to
update the driver to no longer assume that the EC interrupt pin should
be enabled for wake.
Add the wakeup-source property to all cros-ec-spi compatible device
nodes to signify to the driver that they should still be a valid wakeup
source.
Signed-off-by: Mark Hasemeyer <markhas@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The PHY is configured in 10GBASE-R, so make sure to reflect that in DT.
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The J722S is a family of application processors built for Automotive and
Linux Application development. J722S family of SoCs is a superset of the
AM62P SoC family and shares similar memory map, thus the nodes are being
reused from AM62P includes instead of duplicating the definitions.
Some highlights of J722S SoC (in addition to AM62P SoC features) are:
* Two Cortex-R5F for Functional Safety or general-purpose usage and
two C7x floating point vector DSP with Matrix Multiply Accelerator
for deep learning.
* Vision Processing Accelerator (VPAC) with image signal processor
and Depth and Motion Processing Accelerator (DMPAC).
* 7xUARTs, 3xSPI, 5xI2C, 2xUSB2, 2xCAN-FD, 3xMMC and SD, GPMC for
NAND/FPGA connection, OSPI memory controller, 5xMcASP for audio,
4xCSI-RX for Camera, 1 PCIe Gen3 controller, USB3.0 eCAP/eQEP,
ePWM, among other peripherals.
For those interested, more details about this SoC can be found in the
Technical Reference Manual here:
https://www.ti.com/lit/zip/sprujb3
Co-developed-by: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com>
Link: https://lore.kernel.org/r/20240206100608.127702-3-vaishnav.a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Main differences between the new variant and Advanced PG2:
1. Arduino interface is removed. Instead, an new ASIC is added for
communicating with PLC 1200 signal modules.
2. USB 3.0 type A connector is removed, only USB 2.0 type A connector is
available.
3. DP interface is removed. Instead, to communicate with PLC 1200 signal
modules, a USB 3.0 type B connector is added but the signals are
actually not USB.
4. DDR size is increased to 4 GB.
5. Two sensors are added, one tilt sensor and one light sensor.
The light sensor it not yet added to the DT at this stage as it depends
on to-be-added bindings.
Co-developed-by: Chao Zeng <chao.zeng@siemens.com>
Signed-off-by: Chao Zeng <chao.zeng@siemens.com>
Co-developed-by: Li Hua Qian <huaqian.li@siemens.com>
Signed-off-by: Li Hua Qian <huaqian.li@siemens.com>
Signed-off-by: Baocheng Su <baocheng.su@siemens.com>
[Jan: rebase over dtsi refactorings, split-out light sensor, improve LEDs]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Link: https://lore.kernel.org/r/d24e920547986499f6e8e39c833e414679b12ab4.1707463401.git.jan.kiszka@siemens.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
There is a variant coming which does not support the Display Port. Move
all related bits into a separate dtsi so that only those variants
supporting the interface can include it.
Along that, remove a redundant clock setting from
k3-am65-iot2050-common-pg1.dtsi.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Link: https://lore.kernel.org/r/3397d917d7c97f7aec05bc5f65eef3a6fe843650.1707463401.git.jan.kiszka@siemens.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
A new variant is to be added which will not have a arduino connector
like the existing ones. Factor out all bits that are specific to this
connector.
The split is not perfect because wkup_gpio0 is defined based on what is
common to all variants having the connector, thus containing also
connector-unrelated information. But this is still cleaner than
replicating this node into all 4 variants.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Link: https://lore.kernel.org/r/3366367dc9f190c9e21027b9a810886791e99245.1707463401.git.jan.kiszka@siemens.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The R5 lockstep disabling should be common for all PG2 boards, move it
from variants dts to common-pg2.dtsi.
As now the Basic PG2 consumes this twice, move Basic disabling to the
PG1 variant.
Signed-off-by: Baocheng Su <baocheng.su@siemens.com>
[Jan: avoid duplication of disabling for Basic PG2]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Link: https://lore.kernel.org/r/f692d0211915aefd4de7c9ecff5234683c9c7d59.1707463401.git.jan.kiszka@siemens.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
AM62 USB works with some devices, while failing to operate with others.
[ 560.189822] xhci-hcd xhci-hcd.4.auto: xHCI Host Controller
[ 560.195631] xhci-hcd xhci-hcd.4.auto: new USB bus registered, assigned bus number 2
[ 574.388509] xhci-hcd xhci-hcd.4.auto: can't setup: -110
[ 574.393814] xhci-hcd xhci-hcd.4.auto: USB bus 2 deregistered
[ 574.399544] xhci-hcd: probe of xhci-hcd.4.auto failed with error -110
This seems to be related to LPM (Link Power Management), and disabling it
turns USB into reliable working state.
As per AM62 reference manual:
> 4.8.2.1 USB2SS Unsupported Features
>
> The following features are not supported on this family of devices:
> ...
> - USB 2.0 ECN: Link Power Management (LPM)
> ...
Fixes: 2240f96cf3 ("arm64: dts: ti: k3-am62-main: Add support for USB")
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20240209130213.38908-1-andrejs.cainikovs@gmail.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Set VDD_CORE minimum voltage to 0.75V, TI AM62 can run at either 0.75V
or 0.85V depending on the actual speed grade and on the maximum
configured speed (1.4GHz frequency requires 0.85V).
The actual value is programmed into the PMIC EEPROM during manufacturing
(according to the SOC speed grade) and this ensure that both the voltage
values are valid and therefore the OS will not overwrite the value
programmed into the PMIC.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20240213155622.18309-1-francesco@dolcini.it
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The devices in the wkup domain are capable of waking up the system from
suspend. We can configure the wkup domain devices in a generic way using
the ti-sysc interconnect target module driver like we have done with the
earlier TI SoCs.
As ti-sysc manages the SYSCONFIG related registers independent of the
child hardware device, the wake-up configuration is also set even if
wkup_uart0 is reserved by sysfw.
The wkup_uart0 device has interconnect target module register mapping like
dra7 wkup uart. There is a 1 MB interconnect target range with one uart IP
block in the target module. The power domain and clock affects the whole
interconnect target module.
Note we change the functional clock name to follow the ti-sysc binding
and use "fck" instead of "fclk".
Also note that we need to disable the target module reset as noted by
Markus. Otherwise the sysfw using wkup_uart0 can get confused on some
devices leading to boot time issues such as mbox timeouts.
Tested-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Markus Schneider-Pargmann <msp@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20240213112510.6334-1-tony@atomide.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The phyBOARD-Lyra has a GPIO fan header. This overlay enables the fan
header and sets the fan to turn on at 65C.
Signed-off-by: Nathan Morrisson <nmorrisson@phytec.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240213005248.1027842-1-nmorrisson@phytec.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The tps659413 and tps659411 nodes set WKUP_GPIO0_7 (G28) pin as input
to be used as PMIC interrupt but uses 9 (WKUP_GPIO0_9) as
"interrupts" property.
Replace 9 by 7 for both tps659413 and tps659411 after checking in the
board schematic [1].
[1] https://www.ti.com/tool/SK-TDA4VM
Fixes: b808cef0be ("arm64: dts: ti: k3-j721e-sk: Add TPS6594 family PMICs")
Cc: Neha Malcom Francis <n-francis@ti.com>
Signed-off-by: Romain Naour <romain.naour@smile.fr>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Link: https://lore.kernel.org/r/20240209171146.307465-2-romain.naour@smile.fr
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The tps659413 node set WKUP_GPIO0_83 (AA37) pin as input to be used as
PMIC interrupt but uses 39 (WKUP_GPIO0_39) as "interrupts" property.
Replace 39 by 83 after checking in the board schematic [1].
[1] https://www.ti.com/tool/SK-AM69
Fixes: 865a1593bf ("arm64: dts: ti: k3-am69-sk: Add support for TPS6594 PMIC")
Cc: Neha Malcom Francis <n-francis@ti.com>
Signed-off-by: Romain Naour <romain.naour@smile.fr>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Link: https://lore.kernel.org/r/20240209171146.307465-1-romain.naour@smile.fr
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add support for Verdin USB1 interface, implements role switch
functionality using "gpio-usb-b-connector", VBUS is also now
controlled with "regulator-fixed" using a standard GPIO.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20240209130106.38739-1-andrejs.cainikovs@gmail.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Enable both SERDES and PCIe DT nodes in order to get PCIe working on
the SERDES PCIe x2 personality card.
The daughter card also has a USB 2.0 dual-role port. As the base board
already supports a 2.0 dual-role port, enable the port on the SERDES
card to be a host only port.
This will prevent user confusion as having 2 ports in device mode often
leads to confusion as to which port is bound to the gadget function driver.
The PCIe x2 card is provided with the AM65x IDK configuration [1]
so apply the overlay to k3-am654-idk.dtb
[1] https://www.ti.com/lit/ug/spruim6a/spruim6a.pdf
Co-developed-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20240208-for-v6-9-am65-overlays-2-0-v2-2-70bae3e91597@kernel.org
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Doug Anderson observed that ChromeOS crashes are being reported which
include failing allocations of order 7 during core dumps due to ptrace
allocating storage for regsets:
chrome: page allocation failure: order:7,
mode:0x40dc0(GFP_KERNEL|__GFP_COMP|__GFP_ZERO),
nodemask=(null),cpuset=urgent,mems_allowed=0
...
regset_get_alloc+0x1c/0x28
elf_core_dump+0x3d8/0xd8c
do_coredump+0xeb8/0x1378
with further investigation showing that this is:
[ 66.957385] DOUG: Allocating 279584 bytes
which is the maximum size of the SVE regset. As Doug observes it is not
entirely surprising that such a large allocation of contiguous memory might
fail on a long running system.
The SVE regset is currently sized to hold SVE registers with a VQ of
SVE_VQ_MAX which is 512, substantially more than the architectural maximum
of 16 which we might see even in a system emulating the limits of the
architecture. Since we don't expose the size we tell the regset core
externally let's define ARCH_SVE_VQ_MAX with the actual architectural
maximum and use that for the regset, we'll still overallocate most of the
time but much less so which will be helpful even if the core is fixed to
not require contiguous allocations.
Specify ARCH_SVE_VQ_MAX in terms of the maximum value that can be written
into ZCR_ELx.LEN (where this is set in the hardware). For consistency
update the maximum SME vector length to be specified in the same style
while we are at it.
We could also teach the ptrace core about runtime discoverable regset sizes
but that would be a more invasive change and this is being observed in
practical systems.
Reported-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20240213-arm64-sve-ptrace-regset-size-v2-1-c7600ca74b9b@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Add the MIDR value of Microsoft Azure Cobalt 100, which is a Microsoft
implemented CPU based on r0p0 of the ARM Neoverse N2 CPU, and therefore
suffers from all the same errata.
CC: stable@vger.kernel.org # 5.15+
Signed-off-by: Easwar Hariharan <eahariha@linux.microsoft.com>
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Link: https://lore.kernel.org/r/20240214175522.2457857-1-eahariha@linux.microsoft.com
Signed-off-by: Will Deacon <will@kernel.org>
Use id-gpios and vbus-gpios instead.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240215093214.796821-3-alexander.stein@ew.tq-group.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
