Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for net-next:
1) Add support to specify a stateful expression in set definitions,
this allows users to specify e.g. counters per set elements.
2) Flowtable software counter support.
3) Flowtable hardware offload counter support, from wenxu.
3) Parallelize flowtable hardware offload requests, from Paul Blakey.
This includes a patch to add one work entry per offload command.
4) Several patches to rework nf_queue refcount handling, from Florian
Westphal.
4) A few fixes for the flowtable tunnel offload: Fix crash if tunneling
information is missing and set up indirect flow block as TC_SETUP_FT,
patch from wenxu.
5) Stricter netlink attribute sanity check on filters, from Romain Bellan
and Florent Fourcot.
5) Annotations to make sparse happy, from Jules Irenge.
6) Improve icmp errors in debugging information, from Haishuang Yan.
7) Fix warning in IPVS icmp error debugging, from Haishuang Yan.
8) Fix endianess issue in tcp extension header, from Sergey Marinkevich.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous patch allowed device drivers to publish their default
binding between packet trap policers and packet trap groups. However,
some users might not be content with this binding and would like to
change it.
In case user space passed a packet trap policer identifier when setting
a packet trap group, invoke the appropriate device driver callback and
pass the new policer identifier.
v2:
* Check for presence of 'DEVLINK_ATTR_TRAP_POLICER_ID' in
devlink_trap_group_set() and bail if not present
* Add extack error message in case trap group was partially modified
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packet trap groups are used to aggregate logically related packet traps.
Currently, these groups allow user space to batch operations such as
setting the trap action of all member traps.
In order to prevent the CPU from being overwhelmed by too many trapped
packets, it is desirable to bind a packet trap policer to these groups.
For example, to limit all the packets that encountered an exception
during routing to 10Kpps.
Allow device drivers to bind default packet trap policers to packet trap
groups when the latter are registered with devlink.
The next patch will enable user space to change this default binding.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Devices capable of offloading the kernel's datapath and perform
functions such as bridging and routing must also be able to send (trap)
specific packets to the kernel (i.e., the CPU) for processing.
For example, a device acting as a multicast-aware bridge must be able to
trap IGMP membership reports to the kernel for processing by the bridge
module.
In most cases, the underlying device is capable of handling packet rates
that are several orders of magnitude higher compared to those that can
be handled by the CPU.
Therefore, in order to prevent the underlying device from overwhelming
the CPU, devices usually include packet trap policers that are able to
police the trapped packets to rates that can be handled by the CPU.
This patch allows capable device drivers to register their supported
packet trap policers with devlink. User space can then tune the
parameters of these policer (currently, rate and burst size) and read
from the device the number of packets that were dropped by the policer,
if supported.
Subsequent patches in the series will allow device drivers to create
default binding between these policers and packet trap groups and allow
user space to change the binding.
v2:
* Add 'strict_start_type' in devlink policy
* Have device drivers provide max/min rate/burst size for each policer.
Use them to check validity of user provided parameters
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2020-03-29
Here are a few more Bluetooth patches for the 5.7 kernel:
- Fix assumption of encryption key size when reading fails
- Add support for DEFER_SETUP with L2CAP Enhanced Credit Based Mode
- Fix issue with auto-connected devices
- Fix suspend handling when entering the state fails
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The approach taken to pass the port policer methods on to drivers is
pragmatic. It is similar to the port mirroring implementation (in that
the DSA core does all of the filter block interaction and only passes
simple operations for the driver to implement) and dissimilar to how
flow-based policers are going to be implemented (where the driver has
full control over the flow_cls_offload data structure).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When health reporter is registered to devlink, devlink will implicitly set
auto recover if and only if the reporter has a recover method. No reason
to explicitly get the auto recover flag from the driver.
Remove this flag from all drivers that called
devlink_health_reporter_create.
All existing health reporters set auto recovery to true if they have a
recover method.
Yet, administrator can unset auto recover via netlink command as prior to
this patch.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It may be up to the driver (in case ANY HW stats is passed) to select
which type of HW stats he is going to use. Add an infrastructure to
expose this information to user.
$ tc filter add dev enp3s0np1 ingress proto ip handle 1 pref 1 flower dst_ip 192.168.1.1 action drop
$ tc -s filter show dev enp3s0np1 ingress
filter protocol ip pref 1 flower chain 0
filter protocol ip pref 1 flower chain 0 handle 0x1
eth_type ipv4
dst_ip 192.168.1.1
in_hw in_hw_count 2
action order 1: gact action drop
random type none pass val 0
index 1 ref 1 bind 1 installed 10 sec used 10 sec
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
used_hw_stats immediate <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a helper to pass value and selector to. The helper packs them
into struct and puts them into netlink message.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2020-03-28
1) Use kmem_cache_zalloc() instead of kmem_cache_alloc()
in xfrm_state_alloc(). From Huang Zijiang.
2) esp_output_fill_trailer() is the same in IPv4 and IPv6,
so share this function to avoide code duplcation.
From Raed Salem.
3) Add offload support for esp beet mode.
From Xin Long.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds functionality to configure routes for RPL source routing
functionality. There is no IPIP functionality yet implemented which can
be added later when the cases when to use IPv6 encapuslation comes more
clear.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The build_state callback of lwtunnel doesn't contain the net namespace
structure yet. This patch will add it so we can check on specific
address configuration at creation time of rpl source routes.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds rpl source routing receive handling. Everything works
only if sysconf "rpl_seg_enabled" and source routing is enabled. Mostly
the same behaviour as IPv6 segmentation routing. To handle compression
and uncompression a rpl.c file is created which contains the necessary
functionality. The receive handling will also care about IPv6
encapsulated so far it's specified as possible nexthdr in RFC 6554.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a functionality to addrconf to check on a specific RPL
address configuration. According to RFC 6554:
To detect loops in the SRH, a router MUST determine if the SRH
includes multiple addresses assigned to any interface on that
router. If such addresses appear more than once and are separated by
at least one address not assigned to that router.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Exported via same /proc file as the Linux TCP MIB counters, so "netstat -s"
or "nstat" will show them automatically.
The MPTCP MIB counters are allocated in a distinct pcpu area in order to
avoid bloating/wasting TCP pcpu memory.
Counters are allocated once the first MPTCP socket is created in a
network namespace and free'd on exit.
If no sockets have been allocated, all-zero mptcp counters are shown.
The MIB counter list is taken from the multipath-tcp.org kernel, but
only a few counters have been picked up so far. The counter list can
be increased at any time later on.
v2 -> v3:
- remove 'inline' in foo.c files (David S. Miller)
Co-developed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Subflow creation may be initiated by the path manager when
the primary connection is fully established and a remote
address has been received via ADD_ADDR.
Create an in-kernel sock and use kernel_connect() to
initiate connection.
Passive sockets can't acquire the mptcp socket lock at
subflow creation time, so an additional list protected by
a new spinlock is used to track the MPJ subflows.
Such list is spliced into conn_list tail every time the msk
socket lock is acquired, so that it will not interfere
with data flow on the original connection.
Data flow and connection failover not addressed by this commit.
Co-developed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Co-developed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Co-developed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Peter Krystad <peter.krystad@linux.intel.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Process the MP_JOIN option in a SYN packet with the same flow
as MP_CAPABLE but when the third ACK is received add the
subflow to the MPTCP socket subflow list instead of adding it to
the TCP socket accept queue.
The subflow is added at the end of the subflow list so it will not
interfere with the existing subflows operation and no data is
expected to be transmitted on it.
Co-developed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Co-developed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Peter Krystad <peter.krystad@linux.intel.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add handling for sending and receiving the ADD_ADDR, ADD_ADDR6,
and RM_ADDR suboptions.
Co-developed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Co-developed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Peter Krystad <peter.krystad@linux.intel.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add nf_ct_acct_add function to update the conntrack counter
with packets and bytes.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The refcount is done via entry->skb, which does work fine.
Major problem: When putting the refcount of the bridge ports, we
must always put the references while the skb is still around.
However, we will need to put the references after okfn() to avoid
a possible 1 -> 0 -> 1 refcount transition, so we cannot use the
skb pointer anymore.
Place the physports in the queue entry structure instead to allow
for refcounting changes in the next patch.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This is a preparation patch, no logical changes.
Move free_entry into core and rename it to something more sensible.
Will ease followup patches which will complicate the refcount handling.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Many switches don't have an explicit knob for configuring the MTU
(maximum transmission unit per interface). Instead, they do the
length-based packet admission checks on the ingress interface, for
reasons that are easy to understand (why would you accept a packet in
the queuing subsystem if you know you're going to drop it anyway).
So it is actually the MRU that these switches permit configuring.
In Linux there only exists the IFLA_MTU netlink attribute and the
associated dev_set_mtu function. The comments like to play blind and say
that it's changing the "maximum transfer unit", which is to say that
there isn't any directionality in the meaning of the MTU word. So that
is the interpretation that this patch is giving to things: MTU == MRU.
When 2 interfaces having different MTUs are bridged, the bridge driver
MTU auto-adjustment logic kicks in: what br_mtu_auto_adjust() does is it
adjusts the MTU of the bridge net device itself (and not that of the
slave net devices) to the minimum value of all slave interfaces, in
order for forwarded packets to not exceed the MTU regardless of the
interface they are received and send on.
The idea behind this behavior, and why the slave MTUs are not adjusted,
is that normal termination from Linux over the L2 forwarding domain
should happen over the bridge net device, which _is_ properly limited by
the minimum MTU. And termination over individual slave devices is
possible even if those are bridged. But that is not "forwarding", so
there's no reason to do normalization there, since only a single
interface sees that packet.
The problem with those switches that can only control the MRU is with
the offloaded data path, where a packet received on an interface with
MRU 9000 would still be forwarded to an interface with MRU 1500. And the
br_mtu_auto_adjust() function does not really help, since the MTU
configured on the bridge net device is ignored.
In order to enforce the de-facto MTU == MRU rule for these switches, we
need to do MTU normalization, which means: in order for no packet larger
than the MTU configured on this port to be sent, then we need to limit
the MRU on all ports that this packet could possibly come from. AKA
since we are configuring the MRU via MTU, it means that all ports within
a bridge forwarding domain should have the same MTU.
And that is exactly what this patch is trying to do.
>From an implementation perspective, we try to follow the intent of the
user, otherwise there is a risk that we might livelock them (they try to
change the MTU on an already-bridged interface, but we just keep
changing it back in an attempt to keep the MTU normalized). So the MTU
that the bridge is normalized to is either:
- The most recently changed one:
ip link set dev swp0 master br0
ip link set dev swp1 master br0
ip link set dev swp0 mtu 1400
This sequence will make swp1 inherit MTU 1400 from swp0.
- The one of the most recently added interface to the bridge:
ip link set dev swp0 master br0
ip link set dev swp1 mtu 1400
ip link set dev swp1 master br0
The above sequence will make swp0 inherit MTU 1400 as well.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is useful be able to configure port policers on a switch to accept
frames of various sizes:
- Increase the MTU for better throughput from the default of 1500 if it
is known that there is no 10/100 Mbps device in the network.
- Decrease the MTU to limit the latency of high-priority frames under
congestion, or work around various network segments that add extra
headers to packets which can't be fragmented.
For DSA slave ports, this is mostly a pass-through callback, called
through the regular ndo ops and at probe time (to ensure consistency
across all supported switches).
The CPU port is called with an MTU equal to the largest configured MTU
of the slave ports. The assumption is that the user might want to
sustain a bidirectional conversation with a partner over any switch
port.
The DSA master is configured the same as the CPU port, plus the tagger
overhead. Since the MTU is by definition L2 payload (sans Ethernet
header), it is up to each individual driver to figure out if it needs to
do anything special for its frame tags on the CPU port (it shouldn't
except in special cases). So the MTU does not contain the tagger
overhead on the CPU port.
However the MTU of the DSA master, minus the tagger overhead, is used as
a proxy for the MTU of the CPU port, which does not have a net device.
This is to avoid uselessly calling the .change_mtu function on the CPU
port when nothing should change.
So it is safe to assume that the DSA master and the CPU port MTUs are
apart by exactly the tagger's overhead in bytes.
Some changes were made around dsa_master_set_mtu(), function which was
now removed, for 2 reasons:
- dev_set_mtu() already calls dev_validate_mtu(), so it's redundant to
do the same thing in DSA
- __dev_set_mtu() returns 0 if ops->ndo_change_mtu is an absent method
That is to say, there's no need for this function in DSA, we can safely
call dev_set_mtu() directly, take the rtnl lock when necessary, and just
propagate whatever errors get reported (since the user probably wants to
be informed).
Some inspiration (mainly in the MTU DSA notifier) was taken from a
vaguely similar patch from Murali and Florian, who are credited as
co-developers down below.
Co-developed-by: Murali Krishna Policharla <murali.policharla@broadcom.com>
Signed-off-by: Murali Krishna Policharla <murali.policharla@broadcom.com>
Co-developed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add definition and documentation for the new generic info
"fw.mgmt.api". This macro specifies the version of the software
interfaces between driver and firmware.
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Jacob Keller <jacob.e.keller@intel.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently flow offload threads are synchronized by the flow block mutex.
Use rw lock instead to increase flow insertion (read) concurrency.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The indirect block setup should use TC_SETUP_FT as the type instead of
TC_SETUP_BLOCK. Adjust existing users of the indirect flow block
infrastructure.
Fixes: b5140a36da ("netfilter: flowtable: add indr block setup support")
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When HW offloading is enabled, offloaded stats should be used, because
s/w stats are wrong and out of sync with the HW in this case.
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows to reference a net_device from a MACsec context. This
is needed to allow implementing MACsec operations in net device drivers.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is trivial since we already have support for the entirely
identical (from the kernel's point of view) RDNSS, DNSSL, etc. that
also contain opaque data that needs to be passed down to userspace
for further processing.
As specified in draft-ietf-6man-ra-pref64-09 (while it is still a draft,
it is purely waiting on the RFC Editor for cleanups and publishing):
PREF64 option contains lifetime and a (up to) 96-bit IPv6 prefix.
The 8-bit identifier of the option type as assigned by the IANA is 38.
Since we lack DNS64/NAT64/CLAT support in kernel at the moment,
thus this option should also be passed on to userland.
See:
https://tools.ietf.org/html/draft-ietf-6man-ra-pref64-09https://www.iana.org/assignments/icmpv6-parameters/icmpv6-parameters.xhtml#icmpv6-parameters-5
Cc: Erik Kline <ek@google.com>
Cc: Jen Linkova <furry@google.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: Michael Haro <mharo@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Acked-By: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an error message when device wasn't found.
While there, also set the bad attribute's offset in extack.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement support for the DEVLINK_CMD_REGION_NEW command for creating
snapshots. This new command parallels the existing
DEVLINK_CMD_REGION_DEL.
In order for DEVLINK_CMD_REGION_NEW to work for a region, the new
".snapshot" operation must be implemented in the region's ops structure.
The desired snapshot id must be provided. This helps avoid confusion on
the purpose of DEVLINK_CMD_REGION_NEW, and keeps the API simpler.
The requested id will be inserted into the xarray tracking the number of
snapshots using each id. If this id is already used by another snapshot
on any region, an error will be returned.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each snapshot created for a devlink region must have an id. These ids
are supposed to be unique per "event" that caused the snapshot to be
created. Drivers call devlink_region_snapshot_id_get to obtain a new id
to use for a new event trigger. The id values are tracked per devlink,
so that the same id number can be used if a triggering event creates
multiple snapshots on different regions.
There is no mechanism for snapshot ids to ever be reused. Introduce an
xarray to store the count of how many snapshots are using a given id,
replacing the snapshot_id field previously used for picking the next id.
The devlink_region_snapshot_id_get() function will use xa_alloc to
insert an initial value of 1 value at an available slot between 0 and
U32_MAX.
The new __devlink_snapshot_id_increment() and
__devlink_snapshot_id_decrement() functions will be used to track how
many snapshots currently use an id.
Drivers must now call devlink_snapshot_id_put() in order to release
their reference of the snapshot id after adding region snapshots.
By tracking the total number of snapshots using a given id, it is
possible for the decrement() function to erase the id from the xarray
when it is not in use.
With this method, a snapshot id can become reused again once all
snapshots that referred to it have been deleted via
DEVLINK_CMD_REGION_DEL, and the driver has finished adding snapshots.
This work also paves the way to introduce a mechanism for userspace to
request a snapshot.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The devlink_snapshot_id_get() function returns a snapshot id. The
snapshot id is a u32, so there is no way to indicate an error code.
A future change is going to possibly add additional cases where this
function could fail. Refactor the function to return the snapshot id in
an argument, so that it can return zero or an error value.
This ensures that snapshot ids cannot be confused with error values, and
aids in the future refactor of snapshot id allocation management.
Because there is no current way to release previously used snapshot ids,
add a simple check ensuring that an error is reported in case the
snapshot_id would over flow.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It does not makes sense that two snapshots for a given region would use
different destructors. Simplify snapshot creation by adding
a .destructor op for regions.
This operation will replace the data_destructor for the snapshot
creation, and makes snapshot creation easier.
Noticed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify the devlink region code in preparation for adding new operations
on regions.
Create a devlink_region_ops structure, and move the name pointer from
within the devlink_region structure into the ops structure (similar to
the devlink_health_reporter_ops).
This prepares the regions to enable support of additional operations in
the future such as requesting snapshots, or accessing the region
directly without a snapshot.
In order to re-use the constant strings in the mlx4 driver their
declaration must be changed to 'const char * const' to ensure the
compiler realizes that both the data and the pointer cannot change.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This field references FLOW_ACTION_PACKET_EDIT. Such action does not exist
though. Instead the field is used for FLOW_ACTION_MANGLE and _ADD.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Overlapping header include additions in macsec.c
A bug fix in 'net' overlapping with the removal of 'version'
string in ena_netdev.c
Overlapping test additions in selftests Makefile
Overlapping PCI ID table adjustments in iwlwifi driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
This uses the DEFER_SETUP flag to group channels with
L2CAP_CREDIT_BASED_CONNECTION_REQ.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
net/netfilter/nft_fwd_netdev.c: In function ‘nft_fwd_netdev_eval’:
net/netfilter/nft_fwd_netdev.c:32:10: error: ‘struct sk_buff’ has no member named ‘tc_redirected’
pkt->skb->tc_redirected = 1;
^~
net/netfilter/nft_fwd_netdev.c:33:10: error: ‘struct sk_buff’ has no member named ‘tc_from_ingress’
pkt->skb->tc_from_ingress = 1;
^~
To avoid a direct dependency with tc actions from netfilter, wrap the
redirect bits around CONFIG_NET_REDIRECT and move helpers to
include/linux/skbuff.h. Turn on this toggle from the ifb driver, the
only existing client of these bits in the tree.
This patch adds skb_set_redirected() that sets on the redirected bit
on the skbuff, it specifies if the packet was redirect from ingress
and resets the timestamp (timestamp reset was originally missing in the
netfilter bugfix).
Fixes: bcfabee1af ("netfilter: nft_fwd_netdev: allow to redirect to ifb via ingress")
Reported-by: noreply@ellerman.id.au
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a callback to read the socket pid.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Previous changes to the IP routing code have removed all the
tests for the DS_HOST route flag.
Remove the flags and all the code that sets it.
Signed-off-by: David Laight <david.laight@aculab.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packet trap groups are now explicitly registered by drivers and not
implicitly registered when the packet traps are registered. Therefore,
there is no need to encode entire group structure the trap is associated
with inside the trap structure.
Instead, only pass the group identifier. Refer to it as initial group
identifier, as future patches will allow user space to move traps
between groups.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, packet trap groups are implicitly registered by drivers upon
packet trap registration. When the traps are registered, each is
associated with a group and the group is created by devlink, if it does
not exist already.
This makes it difficult for drivers to pass additional attributes for
the groups.
Therefore, as a preparation for future patches that require passing
additional group attributes, add an API to explicitly register /
unregister these groups.
Next patches will convert existing drivers to use this API.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2020-03-21
Implement basic support for the devlink interface in the ice driver.
Additionally pave some necessary changes for adding a devlink region that
exposes the NVM contents.
This series first contains 5 patches for enabling and implementing full NVM
read access via the ETHTOOL_GEEPROM interface. This includes some cleanup of
endian-types, a new function for reading from the NVM and Shadow RAM as a flat
addressable space, a function to calculate the available flash size during
load, and a change to how some of the NVM version fields are stored in the
ice_nvm_info structure.
Following this is 3 patches for implementing devlink support. First, one patch
which implements the basic framework and introduces the ice_devlink.c file.
Second, a patch to implement basic .info_get support. Finally, a patch which
reads the device PBA identifier and reports it as the `board.id` value in the
.info_get response.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 53eca1f347 ("net: rename flow_action_hw_stats_types* ->
flow_action_hw_stats*") renamed just the flow action types and
helpers. For consistency rename variables, enums, struct members
and UAPI too (note that this UAPI was not in any official release,
yet).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nfp driver uses ``fw.bundle_id`` to represent a unique identifier of the
entire firmware bundle.
A future change is going to introduce a similar notion in the ice
driver, so promote ``fw.bundle_id`` into a generic version now.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
