Remove the __init annotation from bmips_cpu_setup() to avoid the
following warning.
WARNING: vmlinux.o(.text+0x35c950): Section mismatch in reference from the function brcmstb_pm_s3() to the function .init.text:bmips_cpu_setup()
The function brcmstb_pm_s3() references
the function __init bmips_cpu_setup().
This is often because brcmstb_pm_s3 lacks a __init
annotation or the annotation of bmips_cpu_setup is wrong.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: linux-mips@linux-mips.org
Reviewed-by: James Hogan <jhogan@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/18589/
Signed-off-by: James Hogan <jhogan@kernel.org>
When a physical CPU is hot-removed, the following warning messages
are shown while the uncore device is removed in uncore_pci_remove():
WARNING: CPU: 120 PID: 5 at arch/x86/events/intel/uncore.c:988
uncore_pci_remove+0xf1/0x110
...
CPU: 120 PID: 5 Comm: kworker/u1024:0 Not tainted 4.15.0-rc8 #1
Workqueue: kacpi_hotplug acpi_hotplug_work_fn
...
Call Trace:
pci_device_remove+0x36/0xb0
device_release_driver_internal+0x145/0x210
pci_stop_bus_device+0x76/0xa0
pci_stop_root_bus+0x44/0x60
acpi_pci_root_remove+0x1f/0x80
acpi_bus_trim+0x54/0x90
acpi_bus_trim+0x2e/0x90
acpi_device_hotplug+0x2bc/0x4b0
acpi_hotplug_work_fn+0x1a/0x30
process_one_work+0x141/0x340
worker_thread+0x47/0x3e0
kthread+0xf5/0x130
When uncore_pci_remove() runs, it tries to get the package ID to
clear the value of uncore_extra_pci_dev[].dev[] by using
topology_phys_to_logical_pkg(). The warning messesages are
shown because topology_phys_to_logical_pkg() returns -1.
arch/x86/events/intel/uncore.c:
static void uncore_pci_remove(struct pci_dev *pdev)
{
...
phys_id = uncore_pcibus_to_physid(pdev->bus);
...
pkg = topology_phys_to_logical_pkg(phys_id); // returns -1
for (i = 0; i < UNCORE_EXTRA_PCI_DEV_MAX; i++) {
if (uncore_extra_pci_dev[pkg].dev[i] == pdev) {
uncore_extra_pci_dev[pkg].dev[i] = NULL;
break;
}
}
WARN_ON_ONCE(i >= UNCORE_EXTRA_PCI_DEV_MAX); // <=========== HERE!!
topology_phys_to_logical_pkg() tries to find
cpuinfo_x86->phys_proc_id that matches the phys_pkg argument.
arch/x86/kernel/smpboot.c:
int topology_phys_to_logical_pkg(unsigned int phys_pkg)
{
int cpu;
for_each_possible_cpu(cpu) {
struct cpuinfo_x86 *c = &cpu_data(cpu);
if (c->initialized && c->phys_proc_id == phys_pkg)
return c->logical_proc_id;
}
return -1;
}
However, the phys_proc_id was already set to 0 by remove_siblinginfo()
when the CPU was offlined.
So, topology_phys_to_logical_pkg() cannot find the correct
logical_proc_id and always returns -1.
As the result, uncore_pci_remove() calls WARN_ON_ONCE() and the warning
messages are shown.
What is worse is that the bogus 'pkg' index results in two bugs:
- We dereference uncore_extra_pci_dev[] with a negative index
- We fail to clean up a stale pointer in uncore_extra_pci_dev[][]
To fix these bugs, remove the clearing of ->phys_proc_id from remove_siblinginfo().
This should not cause any problems, because ->phys_proc_id is not
used after it is hot-removed and it is re-set while hot-adding.
Signed-off-by: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: yasu.isimatu@gmail.com
Cc: <stable@vger.kernel.org>
Fixes: 30bb981185 ("x86/topology: Avoid wasting 128k for package id array")
Link: http://lkml.kernel.org/r/ed738d54-0f01-b38b-b794-c31dc118c207@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
With glibc 2.26 'struct ucontext' is removed to improve POSIX
compliance, which breaks powerpc/alignment_handler selftest. Fix the
test by using ucontext_t. Tested on ppc, works with older glibc
versions as well.
Fixes the following:
alignment_handler.c: In function ‘sighandler’:
alignment_handler.c:68:5: error: dereferencing pointer to incomplete type ‘struct ucontext’
ucp->uc_mcontext.gp_regs[PT_NIP] += 4;
Signed-off-by: Harish <harish@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If KEXEC_CORE is not enabled, powernv builds fail as follows.
arch/powerpc/platforms/powernv/smp.c: In function 'pnv_smp_cpu_kill_self':
arch/powerpc/platforms/powernv/smp.c:236:4: error:
implicit declaration of function 'crash_ipi_callback'
Add dummy function calls, similar to kdump_in_progress(), to solve the
problem.
Fixes: 4145f35864 ("powernv/kdump: Fix cases where the kdump kernel can get HMI's")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit e67e02a544 ("powerpc/pseries: Fix cpu hotplug crash with
memoryless nodes") adds an unconditional call to
find_and_online_cpu_nid(), which is only declared if CONFIG_PPC_SPLPAR
is enabled. This results in the following build error if this is not
the case.
arch/powerpc/platforms/pseries/hotplug-cpu.o: In function `dlpar_online_cpu':
arch/powerpc/platforms/pseries/hotplug-cpu.c:369:
undefined reference to `.find_and_online_cpu_nid'
Follow the guideline provided by similar functions and provide a dummy
function if CONFIG_PPC_SPLPAR is not enabled. This also moves the
external function declaration into an include file where it should be.
Fixes: e67e02a544 ("powerpc/pseries: Fix cpu hotplug crash with memoryless nodes")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
[mpe: Change subject to emphasise the build fix]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On powerpc we allocate page table pages from slab caches of different
sizes. Currently we have a constructor that zeroes out the objects when
we allocate them for the first time.
We expect the objects to be zeroed out when we free the the object
back to slab cache. This happens in the unmap path. For hugetlb pages
we call huge_pte_get_and_clear() to do that.
With the current configuration of page table size, both PUD and PGD
level tables are allocated from the same slab cache. At the PUD level,
we use the second half of the table to store the slot information. But
we never clear that when unmapping.
When such a freed object is then allocated for a PGD page, the second
half of the page table page will not be zeroed as expected. This
results in a kernel crash.
Fix it by always clearing PGD pages when they're allocated.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
[mpe: Change log wording and formatting, add whitespace]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The hugetlb pte entries are at the PMD and PUD level, so we can't use
PTRS_PER_PTE to find the second half of the page table. Use the right
offset for PUD/PMD to get to the second half of the table.
Fixes: bf9a95f9a6 ("powerpc: Free up four 64K PTE bits in 64K backed HPTE pages")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We use the second half of the page table to store slot information, so we must
allocate it always if hugetlb is possible.
Fixes: bf9a95f9a6 ("powerpc: Free up four 64K PTE bits in 64K backed HPTE pages")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
To support memory keys, we moved the hash pte slot information to the
second half of the page table. This was ok with PTE entries at level
4 (PTE page) and level 3 (PMD). We already allocate larger page table
pages at those levels to accomodate extra details. For level 4 we
already have the extra space which was used to track 4k hash page
table entry details and at level 3 the extra space was allocated to
track the THP details.
With hugetlbfs PTE, we used this extra space at the PMD level to store
the slot details. But we also support hugetlbfs PTE at PUD level for
16GB pages and PUD level page didn't allocate extra space. This
resulted in memory corruption.
Fix this by allocating extra space at PUD level when HUGETLB is
enabled.
Fixes: bf9a95f9a6 ("powerpc: Free up four 64K PTE bits in 64K backed HPTE pages")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Radix guests do normally invalidate process-scoped translations when a
new pid is allocated but migrated guests do not invalidate these so
migrated guests crash sometime, especially easy to reproduce with
migration happening within first 10 seconds after the guest boot start
on the same machine.
This adds the "Invalidate process-scoped translations" flush to fix
radix guests migration.
Fixes: 2ee13be34b ("KVM: PPC: Book3S HV: Update kvmppc_set_arch_compat() for ISA v3.00")
Cc: stable@vger.kernel.org # v4.10+
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Tested-by: Laurent Vivier <lvivier@redhat.com>
Tested-by: Daniel Henrique Barboza <danielhb@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
cp_abort is only required for user windows, because kernel context
must not be preempted between a copy/paste pair.
Without this patch, the init task gets used_vas set when it runs the
nx842_powernv_init initcall, which opens windows for kernel usage.
used_vas is then never cleared anywhere, so it gets propagated into
all other tasks. It's a property of the address space, so it should
really be cleared when a new mm is created (or in dup_mmap if the
mmaps are marked as VM_DONTCOPY). For now we seem to have no such
driver, so leave that for another patch.
Fixes: 6c8e6bb2a5 ("powerpc/vas: Add support for user receive window")
Cc: stable@vger.kernel.org # v4.15+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently if the kernel receives a memory hot-unplug event early
enough, it may get stuck in an infinite loop in
dissolve_free_huge_pages(). This appears as a stall just after:
pseries-hotplug-mem: Attempting to hot-remove XX LMB(s) at YYYYYYYY
It appears to be caused by "minimum_order" being uninitialized, due to
init_ras_IRQ() executing before hugetlb_init().
To correct this, extract the part of init_ras_IRQ() that enables
hotplug event processing and place it in the machine_late_initcall
phase, which is guaranteed to be after hugetlb_init() is called.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Acked-by: Balbir Singh <bsingharora@gmail.com>
[mpe: Reorder the functions to make the diff readable]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Mark noticed that he had sporadic "spinlock recursion" warnings from
the DEBUG_SPINLOCK code. Now rq->lock is special in that the owner
changes in the middle of a context switch.
It so happens that we fix up the lock.owner too late, @prev can run
(remotely) the moment prev->on_cpu is cleared, this then allows @prev
to again try and acquire this rq->lock and trigger this warning.
So we have to switch lock.owner before clearing prev->on_cpu.
Do this by moving the DEBUG_SPINLOCK annotation from after switch_to()
to before switch_to() and collect all lockdep annotations there into
prepare_lock_switch() to mirror the existing finish_lock_switch().
Debugged-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
rq->clock_task may be updated between the two calls of
rq_clock_task() in update_curr_rt(). Calling rq_clock_task() only
once makes it more accurate and efficient, taking update_curr() as
reference.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Jiang Biao <jiang.biao2@zte.com.cn>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: zhong.weidong@zte.com.cn
Link: http://lkml.kernel.org/r/1517882008-44552-1-git-send-email-wen.yang99@zte.com.cn
Signed-off-by: Ingo Molnar <mingo@kernel.org>
rq->clock_task may be updated between the two calls of
rq_clock_task() in update_curr_dl(). Calling rq_clock_task() only
once makes it more accurate and efficient, taking update_curr() as
reference.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Jiang Biao <jiang.biao2@zte.com.cn>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: zhong.weidong@zte.com.cn
Link: http://lkml.kernel.org/r/1517882148-44599-1-git-send-email-wen.yang99@zte.com.cn
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The vsyscall page should be visible only if vsyscall=emulate/native when dumping /proc/kcore.
Signed-off-by: Jia Zhang <zhang.jia@linux.alibaba.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: jolsa@redhat.com
Link: http://lkml.kernel.org/r/1518446694-21124-3-git-send-email-zhang.jia@linux.alibaba.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit:
df04abfd18 ("fs/proc/kcore.c: Add bounce buffer for ktext data")
... introduced a bounce buffer to work around CONFIG_HARDENED_USERCOPY=y.
However, accessing the vsyscall user page will cause an SMAP fault.
Replace memcpy() with copy_from_user() to fix this bug works, but adding
a common way to handle this sort of user page may be useful for future.
Currently, only vsyscall page requires KCORE_USER.
Signed-off-by: Jia Zhang <zhang.jia@linux.alibaba.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: jolsa@redhat.com
Link: http://lkml.kernel.org/r/1518446694-21124-2-git-send-email-zhang.jia@linux.alibaba.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
On 64-bit builds, we should not rely on "int $0x80" working (it only does if
CONFIG_IA32_EMULATION=y is enabled).
Without this patch, the move test may succeed, but the "int $0x80" causes
a segfault, resulting in a false negative output of this self-test.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Dmitry Safonov <dsafonov@virtuozzo.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kselftest@vger.kernel.org
Cc: shuah@kernel.org
Link: http://lkml.kernel.org/r/20180211111013.16888-4-linux@dominikbrodowski.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This also gets rid of two build warnings:
protection_keys.c: In function ‘dumpit’:
protection_keys.c:419:3: warning: ignoring return value of ‘write’, declared with attribute warn_unused_result [-Wunused-result]
write(1, buf, nr_read);
^~~~~~~~~~~~~~~~~~~~~~
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Shuah Khan <shuahkh@osg.samsung.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Replace a couple of magically connected buffer length literal constants with
a common definition that makes their relationship obvious. Also document
why our sscanf() usage is safe.
No intended functional changes.
Suggested-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Andrew Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kselftest@vger.kernel.org
Cc: shuah@kernel.org
Link: http://lkml.kernel.org/r/20180211205924.GA23210@light.dominikbrodowski.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The vDSO selftest tries to execute a vsyscall unconditionally, even if it
is not present on the test system (e.g. if booted with vsyscall=none or
with CONFIG_LEGACY_VSYSCALL_NONE=y set. Fix this by copying (and tweaking)
the vsyscall check from test_vsyscall.c
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Andrew Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kselftest@vger.kernel.org
Cc: shuah@kernel.org
Link: http://lkml.kernel.org/r/20180211111013.16888-3-linux@dominikbrodowski.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
That macro was touched around 2.5.8 times, judging by the full history
linux repo, but it was unused even then. Get rid of it already.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux@dominikbrodowski.net
Link: http://lkml.kernel.org/r/20180212201318.GD14640@pd.tnic
Signed-off-by: Ingo Molnar <mingo@kernel.org>
With the following commit:
f09d160992d1 ("x86/entry/64: Get rid of the ALLOC_PT_GPREGS_ON_STACK and SAVE_AND_CLEAR_REGS macros")
... one of my suggested improvements triggered a frame pointer warning:
arch/x86/entry/entry_64.o: warning: objtool: paranoid_entry()+0x11: call without frame pointer save/setup
The warning is correct for the build-time code, but it's actually not
relevant at runtime because of paravirt patching. The paravirt swapgs
call gets replaced with either a SWAPGS instruction or NOPs at runtime.
Go back to the previous behavior by removing the ELF function annotation
for paranoid_entry() and adding an unwind hint, which effectively
silences the warning.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kbuild-all@01.org
Cc: tipbuild@zytor.com
Fixes: f09d160992d1 ("x86/entry/64: Get rid of the ALLOC_PT_GPREGS_ON_STACK and SAVE_AND_CLEAR_REGS macros")
Link: http://lkml.kernel.org/r/20180212174503.5acbymg5z6p32snu@treble
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Previously, error_entry() and paranoid_entry() saved the GP registers
onto stack space previously allocated by its callers. Combine these two
steps in the callers, and use the generic PUSH_AND_CLEAR_REGS macro
for that.
This adds a significant amount ot text size. However, Ingo Molnar points
out that:
"these numbers also _very_ significantly over-represent the
extra footprint. The assumptions that resulted in
us compressing the IRQ entry code have changed very
significantly with the new x86 IRQ allocation code we
introduced in the last year:
- IRQ vectors are usually populated in tightly clustered
groups.
With our new vector allocator code the typical per CPU
allocation percentage on x86 systems is ~3 device vectors
and ~10 fixed vectors out of ~220 vectors - i.e. a very
low ~6% utilization (!). [...]
The days where we allocated a lot of vectors on every
CPU and the compression of the IRQ entry code text
mattered are over.
- Another issue is that only a small minority of vectors
is frequent enough to actually matter to cache utilization
in practice: 3-4 key IPIs and 1-2 device IRQs at most - and
those vectors tend to be tightly clustered as well into about
two groups, and are probably already on 2-3 cache lines in
practice.
For the common case of 'cache cold' IRQs it's the depth of
the call chain and the fragmentation of the resulting I$
that should be the main performance limit - not the overall
size of it.
- The CPU side cost of IRQ delivery is still very expensive
even in the best, most cached case, as in 'over a thousand
cycles'. So much stuff is done that maybe contemporary x86
IRQ entry microcode already prefetches the IDT entry and its
expected call target address."[*]
[*] http://lkml.kernel.org/r/20180208094710.qnjixhm6hybebdv7@gmail.com
The "testb $3, CS(%rsp)" instruction in the idtentry macro does not need
modification. Previously, %rsp was manually decreased by 15*8; with
this patch, %rsp is decreased by 15 pushq instructions.
[jpoimboe@redhat.com: unwind hint improvements]
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: dan.j.williams@intel.com
Link: http://lkml.kernel.org/r/20180211104949.12992-7-linux@dominikbrodowski.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
entry_SYSCALL_64_after_hwframe() and nmi() can be converted to use
PUSH_AND_CLEAN_REGS instead of opencoded variants thereof. Due to
the interleaving, the additional XOR-based clearing of R8 and R9
in entry_SYSCALL_64_after_hwframe() should not have any noticeable
negative implications.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: dan.j.williams@intel.com
Link: http://lkml.kernel.org/r/20180211104949.12992-6-linux@dominikbrodowski.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Those instances where ALLOC_PT_GPREGS_ON_STACK is called just before
SAVE_AND_CLEAR_REGS can trivially be replaced by PUSH_AND_CLEAN_REGS.
This macro uses PUSH instead of MOV and should therefore be faster, at
least on newer CPUs.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: dan.j.williams@intel.com
Link: http://lkml.kernel.org/r/20180211104949.12992-5-linux@dominikbrodowski.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Same as is done for syscalls, interleave XOR with PUSH instructions
for exceptions/interrupts, in order to minimize the cost of the
additional instructions required for register clearing.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: dan.j.williams@intel.com
Link: http://lkml.kernel.org/r/20180211104949.12992-4-linux@dominikbrodowski.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
All current code paths call SAVE_C_REGS and then immediately
SAVE_EXTRA_REGS. Therefore, merge these two macros and order the MOV
sequeneces properly.
While at it, remove the macros to save all except specific registers,
as these macros have been unused for a long time.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: dan.j.williams@intel.com
Link: http://lkml.kernel.org/r/20180211104949.12992-2-linux@dominikbrodowski.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Harmonize all the Spectre messages so that a:
dmesg | grep -i spectre
... gives us most Spectre related kernel boot messages.
Also fix a few other details:
- clarify a comment about firmware speculation control
- s/KPTI/PTI
- remove various line-breaks that made the code uglier
Acked-by: David Woodhouse <dwmw@amazon.co.uk>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We either clear the CPU_BASED_USE_MSR_BITMAPS and end up intercepting all
MSR accesses or create a valid L02 MSR bitmap and use that. This decision
has to be made every time we evaluate whether we are going to generate the
L02 MSR bitmap.
Before commit:
d28b387fb7 ("KVM/VMX: Allow direct access to MSR_IA32_SPEC_CTRL")
... this was probably OK since the decision was always identical.
This is no longer the case now since the MSR bitmap might actually
change once we decide to not intercept SPEC_CTRL and PRED_CMD.
Signed-off-by: KarimAllah Ahmed <karahmed@amazon.de>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: arjan.van.de.ven@intel.com
Cc: dave.hansen@intel.com
Cc: jmattson@google.com
Cc: kvm@vger.kernel.org
Cc: sironi@amazon.de
Link: http://lkml.kernel.org/r/1518305967-31356-6-git-send-email-dwmw@amazon.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
These two variables should check whether SPEC_CTRL and PRED_CMD are
supposed to be passed through to L2 guests or not. While
msr_write_intercepted_l01 would return 'true' if it is not passed through.
So just invert the result of msr_write_intercepted_l01 to implement the
correct semantics.
Signed-off-by: KarimAllah Ahmed <karahmed@amazon.de>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Jim Mattson <jmattson@google.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: arjan.van.de.ven@intel.com
Cc: dave.hansen@intel.com
Cc: kvm@vger.kernel.org
Cc: sironi@amazon.de
Fixes: 086e7d4118cc ("KVM: VMX: Allow direct access to MSR_IA32_SPEC_CTRL")
Link: http://lkml.kernel.org/r/1518305967-31356-5-git-send-email-dwmw@amazon.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
With retpoline, tight loops of "call this function for every XXX" are
very much pessimised by taking a prediction miss *every* time. This one
is by far the biggest contributor to the guest launch time with retpoline.
By marking the iterator slot_handle_…() functions always_inline, we can
ensure that the indirect function call can be optimised away into a
direct call and it actually generates slightly smaller code because
some of the other conditionals can get optimised away too.
Performance is now pretty close to what we see with nospectre_v2 on
the command line.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Filippo Sironi <sironi@amazon.de>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Filippo Sironi <sironi@amazon.de>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: arjan.van.de.ven@intel.com
Cc: dave.hansen@intel.com
Cc: jmattson@google.com
Cc: karahmed@amazon.de
Cc: kvm@vger.kernel.org
Cc: rkrcmar@redhat.com
Link: http://lkml.kernel.org/r/1518305967-31356-4-git-send-email-dwmw@amazon.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This reverts commit 64e16720ea.
We cannot call C functions like that, without marking all the
call-clobbered registers as, well, clobbered. We might have got away
with it for now because the __ibp_barrier() function was *fairly*
unlikely to actually use any other registers. But no. Just no.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: arjan.van.de.ven@intel.com
Cc: dave.hansen@intel.com
Cc: jmattson@google.com
Cc: karahmed@amazon.de
Cc: kvm@vger.kernel.org
Cc: pbonzini@redhat.com
Cc: rkrcmar@redhat.com
Cc: sironi@amazon.de
Link: http://lkml.kernel.org/r/1518305967-31356-3-git-send-email-dwmw@amazon.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Arjan points out that the Intel document only clears the 0xc2 microcode
on *some* parts with CPUID 506E3 (INTEL_FAM6_SKYLAKE_DESKTOP stepping 3).
For the Skylake H/S platform it's OK but for Skylake E3 which has the
same CPUID it isn't (yet) cleared.
So removing it from the blacklist was premature. Put it back for now.
Also, Arjan assures me that the 0x84 microcode for Kaby Lake which was
featured in one of the early revisions of the Intel document was never
released to the public, and won't be until/unless it is also validated
as safe. So those can change to 0x80 which is what all *other* versions
of the doc have identified.
Once the retrospective testing of existing public microcodes is done, we
should be back into a mode where new microcodes are only released in
batches and we shouldn't even need to update the blacklist for those
anyway, so this tweaking of the list isn't expected to be a thing which
keeps happening.
Requested-by: Arjan van de Ven <arjan.van.de.ven@intel.com>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: arjan.van.de.ven@intel.com
Cc: dave.hansen@intel.com
Cc: kvm@vger.kernel.org
Cc: pbonzini@redhat.com
Link: http://lkml.kernel.org/r/1518449255-2182-1-git-send-email-dwmw@amazon.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
If the entire device is powered off, we can safely assume that the
engine is also asleep (and idle).
Reported-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: a091d4ee93 ("drm/i915: Hold a wakeref for probing the ring registers")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180212093928.6005-1-chris@chris-wilson.co.uk
(cherry picked from commit 74d00d28a1)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Userspace provides a 64b value for the priority, we need to be careful
to preserve the full range before validation to prevent truncation (and
letting an illegal value pass).
Reported-by: Antonio Argenziano <antonio.argenziano@intel.com>
Fixes: ac14fbd460 ("drm/i915/scheduler: Support user-defined priorities")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Antonio Argenziano <antonio.argenziano@intel.com>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180208085151.11480-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
(cherry picked from commit 11a18f6319)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
drivers/gpu/drm/i915/i915_oa_cnl.c: In function ‘i915_perf_load_test_config_cnl’:
drivers/gpu/drm/i915/i915_oa_cnl.c:99:2: error: ‘strncpy’ output truncated before terminating nul copying 36 bytes from a string of the same length [-Werror=stringop-truncation]
v2: strlcpy
Fixes: 95690a02fb ("drm/i915/perf: enable perf support on CNL")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180208102403.5587-2-chris@chris-wilson.co.uk
(cherry picked from commit 020580ff8e)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
drivers/gpu/drm/i915/i915_oa_cflgt3.c: In function ‘i915_perf_load_test_config_cflgt3’:
drivers/gpu/drm/i915/i915_oa_cflgt3.c:87:2: error: ‘strncpy’ output truncated before terminating nul copying 36 bytes from a string of the same length [-Werror=stringop-truncation]
v2: strlcpy
Fixes: 4407eaa9b0 ("drm/i915/perf: add support for Coffeelake GT3")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180208102403.5587-1-chris@chris-wilson.co.uk
(cherry picked from commit 43df81d324)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
A user reports a really bad temperature on Ryzen 1950X.
k10temp-pci-00cb
Adapter: PCI adapter
temp1: +4294948.3°C (high = +70.0°C)
This will happen if the temperature reported by the chip is lower than
the offset temperature. This has been seen in the field if "Sense MI Skew"
and/or "Sense MI Offset" BIOS parameters were set to unexpected values.
Let's report a temperature of 0 degrees C in that case.
Fixes: 1b50b77635 ("hwmon: (k10temp) Add support for temperature offsets")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
In nvme_keep_alive() we pass a request with a pointer to an NVMe command on
the stack into blk_execute_rq_nowait(). However, the block layer doesn't
guarantee that the request is fully queued before blk_execute_rq_nowait()
returns. If not, and the request is queued after nvme_keep_alive() returns,
then we'll end up using stack memory that might have been overwritten to
form the NVMe command we pass to hardware.
Fix this by keeping a special command struct in the nvme_ctrl struct right
next to the delayed work struct used for keep-alives.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Pull crypto fixes from Herbert Xu:
"This fixes the following issues:
- oversize stack frames on mn10300 in sha3-generic
- warning on old compilers in sha3-generic
- API error in sun4i_ss_prng
- potential dead-lock in sun4i_ss_prng
- null-pointer dereference in sha512-mb
- endless loop when DECO acquire fails in caam
- kernel oops when hashing empty message in talitos"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: sun4i_ss_prng - convert lock to _bh in sun4i_ss_prng_generate
crypto: sun4i_ss_prng - fix return value of sun4i_ss_prng_generate
crypto: caam - fix endless loop when DECO acquire fails
crypto: sha3-generic - Use __optimize to support old compilers
compiler-gcc.h: __nostackprotector needs gcc-4.4 and up
compiler-gcc.h: Introduce __optimize function attribute
crypto: sha3-generic - deal with oversize stack frames
crypto: talitos - fix Kernel Oops on hashing an empty file
crypto: sha512-mb - initialize pending lengths correctly
Various PCI_DMA_BUS_IS_PHYS implementations rely on this flag to make proper
decisions for block and networking addressability.
Signed-off-by: Christoph Hellwig <hch@lst.de>
arch/ia64/kernel/pci-swiotlb.c is removed in commit 4fac8076df ("ia64: clean up swiotlb support")
but pci-swiotlb.o is still present in Makefile, and so build fail when
CONFIG_SWIOTLB is enabled.
Fix the build failure by removing pci-swiotlb.o from makefile
Fixes: 4fac8076df ("ia64: clean up swiotlb support")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
References to CPU part number MIDR_QCOM_FALKOR were dropped from the
mailing list patch due to mainline/arm64 branch dependency. So this
patch adds the missing part number.
Fixes: ec82b567a7 ("arm64: Implement branch predictor hardening for Falkor")
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Commit f859422075 (x86: PM: Make APM idle driver initialize polling
state) made apm_init() call cpuidle_poll_state_init(), but that only
is defined for CONFIG_CPU_IDLE set, so make the empty stub of it
available for CONFIG_CPU_IDLE unset too to fix the resulting build
issue.
Fixes: f859422075 (x86: PM: Make APM idle driver initialize polling state)
Cc: 4.14+ <stable@vger.kernel.org> # 4.14+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
