Handle L2 TLB flush requests by going through all vCPUs and checking
whether there are vCPUs running the same VM_ID with a VP_ID specified
in the requests. Perform synthetic exit to L2 upon finish.
Note, while checking VM_ID/VP_ID of running vCPUs seem to be a bit
racy, we count on the fact that KVM flushes the whole L2 VPID upon
transition. Also, KVM_REQ_HV_TLB_FLUSH request needs to be done upon
transition between L1 and L2 to make sure all pending requests are
always processed.
For the reference, Hyper-V TLFS refers to the feature as "Direct
Virtual Flush".
Note, nVMX/nSVM code does not handle VMCALL/VMMCALL from L2 yet.
Reviewed-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20221101145426.251680-24-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Print guest pgd in kvm_nested_vmenter() to enrich the information for
tracing. When tdp is enabled, print the value of tdp page table (EPT/NPT);
when tdp is disabled, print the value of non-nested CR3.
Suggested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Mingwei Zhang <mizhang@google.com>
Link: https://lore.kernel.org/r/20220825225755.907001-4-mizhang@google.com
[sean: print nested_cr3 vs. nested_eptp vs. guest_cr3]
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Update trace function for nested VM entry to support VMX. Existing trace
function only supports nested VMX and the information printed out is AMD
specific.
So, rename trace_kvm_nested_vmrun() to trace_kvm_nested_vmenter(), since
'vmenter' is generic. Add a new field 'isa' to recognize Intel and AMD;
Update the output to print out VMX/SVM related naming respectively, eg.,
vmcb vs. vmcs; npt vs. ept.
Opportunistically update the call site of trace_kvm_nested_vmenter() to
make one line per parameter.
Signed-off-by: Mingwei Zhang <mizhang@google.com>
Link: https://lore.kernel.org/r/20220825225755.907001-2-mizhang@google.com
[sean: align indentation, s/update/rename in changelog]
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Track the address and error code as 64-bit values in the page fault
tracepoint. When TDP is enabled, the address is a GPA and thus can be a
64-bit value even on 32-bit hosts. And SVM's #NPF genereates 64-bit
error codes.
Opportunistically clean up the formatting.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently, kvm_page_fault trace point provide fault_address and error
code. However it is not enough to find which cpu and instruction
cause kvm_page_faults. So add vcpu id and instruction pointer in
kvm_page_fault trace point.
Cc: Baik Song An <bsahn@etri.re.kr>
Cc: Hong Yeon Kim <kimhy@etri.re.kr>
Cc: Taeung Song <taeung@reallinux.co.kr>
Cc: linuxgeek@linuxgeek.io
Signed-off-by: Wonhyuk Yang <vvghjk1234@gmail.com>
Link: https://lore.kernel.org/r/20220510071001.87169-1-vvghjk1234@gmail.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
For now, this is basically an excuse to add back the void* argument to
the function, while removing some knowledge of vcpu->arch.pio* from
its callers. The WARN that vcpu->arch.pio.count is zero is also
extended to OUT operations.
The vcpu->arch.pio* fields still need to be filled even when the PIO is
handled in-kernel as __emulator_pio_in() is always followed by
complete_emulator_pio_in(). But after fixing that, it will be possible to
to only populate the vcpu->arch.pio* fields on userspace exits.
No functional change intended.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a tracepoint to track number of doorbells being sent
to signal a running vCPU to process IRQ after being injected.
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Message-Id: <20220519102709.24125-17-suravee.suthikulpanit@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In the IRQ injection tracepoint, differentiate between Hard IRQs and Soft
"IRQs", i.e. interrupts that are reinjected after incomplete delivery of
a software interrupt from an INTn instruction. Tag reinjected interrupts
as such, even though the information is usually redundant since soft
interrupts are only ever reinjected by KVM. Though rare in practice, a
hard IRQ can be reinjected.
Signed-off-by: Sean Christopherson <seanjc@google.com>
[MSS: change "kvm_inj_virq" event "reinjected" field type to bool]
Signed-off-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Message-Id: <9664d49b3bd21e227caa501cff77b0569bebffe2.1651440202.git.maciej.szmigiero@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Print the error code in the exception injection tracepoint if and only if
the exception has an error code. Define the entire error code sequence
as a set of formatted strings, print empty strings if there's no error
code, and abuse __print_symbolic() by passing it an empty array to coerce
it into printing the error code as a hex string.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Message-Id: <e8f0511733ed2a0410cbee8a0a7388eac2ee5bac.1651440202.git.maciej.szmigiero@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Trace exceptions that are re-injected, not just those that KVM is
injecting for the first time. Debugging re-injection bugs is painful
enough as is, not having visibility into what KVM is doing only makes
things worse.
Delay propagating pending=>injected in the non-reinjection path so that
the tracing can properly identify reinjected exceptions.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Message-Id: <25470690a38b4d2b32b6204875dd35676c65c9f2.1651440202.git.maciej.szmigiero@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This can help identify potential performance issues when handles
AVIC incomplete IPI due vCPU not running.
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20220420154954.19305-3-suravee.suthikulpanit@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Trace all APICv inhibit changes instead of just those that result in
APICv being (un)inhibited, and log the current state. Debugging why
APICv isn't working is frustrating as it's hard to see why APICv is still
inhibited, and logging only the first inhibition means unnecessary onion
peeling.
Opportunistically drop the export of the tracepoint, it is not and should
not be used by vendor code due to the need to serialize toggling via
apicv_update_lock.
Note, using the common flow means kvm_apicv_init() switched from atomic
to non-atomic bitwise operations. The VM is unreachable at init, so
non-atomic is perfectly ok.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220311043517.17027-4-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add set/clear wrappers for toggling APICv inhibits to make the call sites
more readable, and opportunistically rename the inner helpers to align
with the new wrappers and to make them more readable as well. Invert the
flag from "activate" to "set"; activate is painfully ambiguous as it's
not obvious if the inhibit is being activated, or if APICv is being
activated, in which case the inhibit is being deactivated.
For the functions that take @set, swap the order of the inhibit reason
and @set so that the call sites are visually similar to those that bounce
through the wrapper.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220311043517.17027-3-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use an enum for the APICv inhibit reasons, there is no meaning behind
their values and they most definitely are not "unsigned longs". Rename
the various params to "reason" for consistency and clarity (inhibit may
be confused as a command, i.e. inhibit APICv, instead of the reason that
is getting toggled/checked).
No functional change intended.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220311043517.17027-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Hide the lapic's "raw" write helper inside lapic.c to force non-APIC code
to go through proper helpers when modification the vAPIC state. Keep the
read helper visible to outsiders for now, refactoring KVM to hide it too
is possible, it will just take more work to do so.
No functional change intended.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220204214205.3306634-11-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Get the number of sparse banks from the VARHEAD field, which the guest is
required to provide as "The size of a variable header, in QWORDS.", where
the variable header is:
Variable Header Bytes = {Total Header Bytes - sizeof(Fixed Header)}
rounded up to nearest multiple of 8
Variable HeaderSize = Variable Header Bytes / 8
In other words, the VARHEAD should match the number of sparse banks.
Keep the manual count as a sanity check, but otherwise rely on the field
so as to more closely align with the logic defined in the TLFS and to
allow for future cleanups.
Tweak the tracepoint output to use "rep_cnt" instead of simply "cnt" now
that there is also "var_cnt".
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20211207220926.718794-3-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This allows to see how many interrupts were delivered via the
APICv/AVIC from the host.
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20211209115440.394441-3-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Extend the get_exit_info static call to provide the reason for the VM
exit. Modify relevant trace points to use this rather than extracting
the reason in the caller.
Signed-off-by: David Edmondson <david.edmondson@oracle.com>
Reviewed-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210920103737.2696756-3-david.edmondson@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Hypercall failures are unusual with potentially far going consequences
so it would be useful to see their results when tracing.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Siddharth Chandrasekaran <sidcha@amazon.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210730122625.112848-3-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rename the SMM tracepoint, which handles both entering and exiting SMM,
from kvm_enter_smm to kvm_smm_transition.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210609185619.992058-8-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use the __string() machinery provided by the tracing subystem to make a
copy of the string literals consumed by the "nested VM-Enter failed"
tracepoint. A complete copy is necessary to ensure that the tracepoint
can't outlive the data/memory it consumes and deference stale memory.
Because the tracepoint itself is defined by kvm, if kvm-intel and/or
kvm-amd are built as modules, the memory holding the string literals
defined by the vendor modules will be freed when the module is unloaded,
whereas the tracepoint and its data in the ring buffer will live until
kvm is unloaded (or "indefinitely" if kvm is built-in).
This bug has existed since the tracepoint was added, but was recently
exposed by a new check in tracing to detect exactly this type of bug.
fmt: '%s%s
' current_buffer: ' vmx_dirty_log_t-140127 [003] .... kvm_nested_vmenter_failed: '
WARNING: CPU: 3 PID: 140134 at kernel/trace/trace.c:3759 trace_check_vprintf+0x3be/0x3e0
CPU: 3 PID: 140134 Comm: less Not tainted 5.13.0-rc1-ce2e73ce600a-req #184
Hardware name: ASUS Q87M-E/Q87M-E, BIOS 1102 03/03/2014
RIP: 0010:trace_check_vprintf+0x3be/0x3e0
Code: <0f> 0b 44 8b 4c 24 1c e9 a9 fe ff ff c6 44 02 ff 00 49 8b 97 b0 20
RSP: 0018:ffffa895cc37bcb0 EFLAGS: 00010282
RAX: 0000000000000000 RBX: ffffa895cc37bd08 RCX: 0000000000000027
RDX: 0000000000000027 RSI: 00000000ffffdfff RDI: ffff9766cfad74f8
RBP: ffffffffc0a041d4 R08: ffff9766cfad74f0 R09: ffffa895cc37bad8
R10: 0000000000000001 R11: 0000000000000001 R12: ffffffffc0a041d4
R13: ffffffffc0f4dba8 R14: 0000000000000000 R15: ffff976409f2c000
FS: 00007f92fa200740(0000) GS:ffff9766cfac0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000559bd11b0000 CR3: 000000019fbaa002 CR4: 00000000001726e0
Call Trace:
trace_event_printf+0x5e/0x80
trace_raw_output_kvm_nested_vmenter_failed+0x3a/0x60 [kvm]
print_trace_line+0x1dd/0x4e0
s_show+0x45/0x150
seq_read_iter+0x2d5/0x4c0
seq_read+0x106/0x150
vfs_read+0x98/0x180
ksys_read+0x5f/0xe0
do_syscall_64+0x40/0xb0
entry_SYSCALL_64_after_hwframe+0x44/0xae
Cc: Steven Rostedt <rostedt@goodmis.org>
Fixes: 380e0055bc ("KVM: nVMX: trace nested VM-Enter failures detected by H/W")
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Message-Id: <20210607175748.674002-1-seanjc@google.com>
Add a new exit reason for emulator to handle Xen hypercalls.
Since this means KVM owns the ABI, dispense with the facility for the
VMM to provide its own copy of the hypercall pages; just fill them in
directly using VMCALL/VMMCALL as we do for the Hyper-V hypercall page.
This behaviour is enabled by a new INTERCEPT_HCALL flag in the
KVM_XEN_HVM_CONFIG ioctl structure, and advertised by the same flag
being returned from the KVM_CAP_XEN_HVM check.
Rename xen_hvm_config() to kvm_xen_write_hypercall_page() and move it
to the nascent xen.c while we're at it, and add a test case.
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Convert kvm_x86_ops to use static calls. Note that all kvm_x86_ops are
covered here except for 'pmu_ops and 'nested ops'.
Here are some numbers running cpuid in a loop of 1 million calls averaged
over 5 runs, measured in the vm (lower is better).
Intel Xeon 3000MHz:
|default |mitigations=off
-------------------------------------
vanilla |.671s |.486s
static call|.573s(-15%)|.458s(-6%)
AMD EPYC 2500MHz:
|default |mitigations=off
-------------------------------------
vanilla |.710s |.609s
static call|.664s(-6%) |.609s(0%)
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Sean Christopherson <seanjc@google.com>
Signed-off-by: Jason Baron <jbaron@akamai.com>
Message-Id: <e057bf1b8a7ad15652df6eeba3f907ae758d3399.1610680941.git.jbaron@akamai.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add trace events for entry to and exit from VMGEXIT MSR protocol
processing. The vCPU will be common for the trace events. The MSR
protocol processing is guided by the GHCB GPA in the VMCB, so the GHCB
GPA will represent the input and output values for the entry and exit
events, respectively. Additionally, the exit event will contain the
return code for the event.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Message-Id: <c5b3b440c3e0db43ff2fc02813faa94fa54896b0.1607620209.git.thomas.lendacky@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add trace events for entry to and exit from VMGEXIT processing. The vCPU
id and the exit reason will be common for the trace events. The exit info
fields will represent the input and output values for the entry and exit
events, respectively.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Message-Id: <25357dca49a38372e8f483753fb0c1c2a70a6898.1607620209.git.thomas.lendacky@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use the newly introduced TRACE_EVENT_KVM_EXIT to define the guts of
kvm_nested_vmexit so that it captures and prints the same information as
kvm_exit. This has the bonus side effect of fixing the interrupt info
and error code printing for the case where they're invalid, e.g. if the
exit was a failed VM-Entry. This also sets the stage for retrieving
EXIT_QUALIFICATION and VM_EXIT_INTR_INFO in nested_vmx_reflect_vmexit()
if and only if the VM-Exit is being routed to L1.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200923201349.16097-7-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Macrofy the definition of kvm_exit so that the definition can be reused
verbatim by kvm_nested_vmexit.
No functional change intended.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200923201349.16097-6-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Extend the kvm_exit tracepoint to align it with kvm_nested_vmexit in
terms of what information is captured. On SVM, add interrupt info and
error code, while on VMX it add IDT vectoring and error code. This
sets the stage for macrofying the kvm_exit tracepoint definition so that
it can be reused for kvm_nested_vmexit without loss of information.
Opportunistically stuff a zero for VM_EXIT_INTR_INFO if the VM-Enter
failed, as the field is guaranteed to be invalid. Note, it'd be
possible to further filter the interrupt/exception fields based on the
VM-Exit reason, but the helper is intended only for tracepoints, i.e.
an extra VMREAD or two is a non-issue, the failed VM-Enter case is just
low hanging fruit.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200923201349.16097-5-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use kvm_rip_read() to read the guest's RIP for the nested VM-Exit
tracepoint instead of having the caller pass in an argument. Params
that are passed into a tracepoint are evaluated even if the tracepoint
is disabled, i.e. passing in RIP for VMX incurs a VMREAD and retpoline
to retrieve a value that may never be used, e.g. if the exit is due to a
hardware interrupt.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200923201349.16097-3-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add RIP to the kvm_entry tracepoint to help debug if the kvm_exit
tracepoint is disabled or if VM-Enter fails, in which case the kvm_exit
tracepoint won't be hit.
Read RIP from within the tracepoint itself to avoid a potential VMREAD
and retpoline if the guest's RIP isn't available.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200923201349.16097-2-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The new intercept bits have been added in vmcb control area to support
few more interceptions. Here are the some of them.
- INTERCEPT_INVLPGB,
- INTERCEPT_INVLPGB_ILLEGAL,
- INTERCEPT_INVPCID,
- INTERCEPT_MCOMMIT,
- INTERCEPT_TLBSYNC,
Add a new intercept word in vmcb_control_area to support these instructions.
Also update kvm_nested_vmrun trace function to support the new addition.
AMD documentation for these instructions is available at "AMD64
Architecture Programmer’s Manual Volume 2: System Programming, Pub. 24593
Rev. 3.34(or later)"
The documentation can be obtained at the links below:
Link: https://www.amd.com/system/files/TechDocs/24593.pdf
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206537
Signed-off-by: Babu Moger <babu.moger@amd.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Message-Id: <159985251547.11252.16994139329949066945.stgit@bmoger-ubuntu>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert all the intercepts to one array of 32 bit vectors in
vmcb_control_area. This makes it easy for future intercept vector
additions. Also update trace functions.
Signed-off-by: Babu Moger <babu.moger@amd.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Message-Id: <159985250813.11252.5736581193881040525.stgit@bmoger-ubuntu>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add support for Hyper-V synthetic debugger (syndbg) interface.
The syndbg interface is using MSRs to emulate a way to send/recv packets
data.
The debug transport dll (kdvm/kdnet) will identify if Hyper-V is enabled
and if it supports the synthetic debugger interface it will attempt to
use it, instead of trying to initialize a network adapter.
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Jon Doron <arilou@gmail.com>
Message-Id: <20200529134543.1127440-4-arilou@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use __print_flags() to display the names of VMX flags in VM-Exit traces
and strip the flags when printing the basic exit reason, e.g. so that a
failed VM-Entry due to invalid guest state gets recorded as
"INVALID_STATE FAILED_VMENTRY" instead of "0x80000021".
Opportunstically fix misaligned variables in the kvm_exit and
kvm_nested_vmexit_inject tracepoints.
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200508235348.19427-3-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* GICv4.1 support
* 32bit host removal
PPC:
* secure (encrypted) using under the Protected Execution Framework
ultravisor
s390:
* allow disabling GISA (hardware interrupt injection) and protected
VMs/ultravisor support.
x86:
* New dirty bitmap flag that sets all bits in the bitmap when dirty
page logging is enabled; this is faster because it doesn't require bulk
modification of the page tables.
* Initial work on making nested SVM event injection more similar to VMX,
and less buggy.
* Various cleanups to MMU code (though the big ones and related
optimizations were delayed to 5.8). Instead of using cr3 in function
names which occasionally means eptp, KVM too has standardized on "pgd".
* A large refactoring of CPUID features, which now use an array that
parallels the core x86_features.
* Some removal of pointer chasing from kvm_x86_ops, which will also be
switched to static calls as soon as they are available.
* New Tigerlake CPUID features.
* More bugfixes, optimizations and cleanups.
Generic:
* selftests: cleanups, new MMU notifier stress test, steal-time test
* CSV output for kvm_stat.
KVM/MIPS has been broken since 5.5, it does not compile due to a patch committed
by MIPS maintainers. I had already prepared a fix, but the MIPS maintainers
prefer to fix it in generic code rather than KVM so they are taking care of it.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAl6GOnIUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroMfxwf/ZKLZiRoaovXCOG71M/eHtQb8ZIqU
3MPy+On3eC5Sk/aBxWUL9EFZsbYG6kYdbZ1VOvG9XPBoLlnkDSm/IR0kaELHtnjj
oGVda/tvGn46Ne39y8xBptmb91WDcWH0vFthT/CwlMxAw3xjr+gG7Qyo+8F2CW6m
SSSuLiHSBnyO1cQKruBTHZ8qnR8LlnfXEqtd6Y4LFLic0LbLIoIdRcT3wjQrcZrm
Djd7wbTEYZjUfoqZ72ekwEDUsONcDLDSKcguDO9pSMSCGhpxCVT5Vy68KRpoIMs2
nzNWDKjvqQo5zb2+GWxJgkd12Hv+n7PCXZMbVrWBu1pQsewUns9m4mkpGw==
=6fGt
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm updates from Paolo Bonzini:
"ARM:
- GICv4.1 support
- 32bit host removal
PPC:
- secure (encrypted) using under the Protected Execution Framework
ultravisor
s390:
- allow disabling GISA (hardware interrupt injection) and protected
VMs/ultravisor support.
x86:
- New dirty bitmap flag that sets all bits in the bitmap when dirty
page logging is enabled; this is faster because it doesn't require
bulk modification of the page tables.
- Initial work on making nested SVM event injection more similar to
VMX, and less buggy.
- Various cleanups to MMU code (though the big ones and related
optimizations were delayed to 5.8). Instead of using cr3 in
function names which occasionally means eptp, KVM too has
standardized on "pgd".
- A large refactoring of CPUID features, which now use an array that
parallels the core x86_features.
- Some removal of pointer chasing from kvm_x86_ops, which will also
be switched to static calls as soon as they are available.
- New Tigerlake CPUID features.
- More bugfixes, optimizations and cleanups.
Generic:
- selftests: cleanups, new MMU notifier stress test, steal-time test
- CSV output for kvm_stat"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (277 commits)
x86/kvm: fix a missing-prototypes "vmread_error"
KVM: x86: Fix BUILD_BUG() in __cpuid_entry_get_reg() w/ CONFIG_UBSAN=y
KVM: VMX: Add a trampoline to fix VMREAD error handling
KVM: SVM: Annotate svm_x86_ops as __initdata
KVM: VMX: Annotate vmx_x86_ops as __initdata
KVM: x86: Drop __exit from kvm_x86_ops' hardware_unsetup()
KVM: x86: Copy kvm_x86_ops by value to eliminate layer of indirection
KVM: x86: Set kvm_x86_ops only after ->hardware_setup() completes
KVM: VMX: Configure runtime hooks using vmx_x86_ops
KVM: VMX: Move hardware_setup() definition below vmx_x86_ops
KVM: x86: Move init-only kvm_x86_ops to separate struct
KVM: Pass kvm_init()'s opaque param to additional arch funcs
s390/gmap: return proper error code on ksm unsharing
KVM: selftests: Fix cosmetic copy-paste error in vm_mem_region_move()
KVM: Fix out of range accesses to memslots
KVM: X86: Micro-optimize IPI fastpath delay
KVM: X86: Delay read msr data iff writes ICR MSR
KVM: PPC: Book3S HV: Add a capability for enabling secure guests
KVM: arm64: GICv4.1: Expose HW-based SGIs in debugfs
KVM: arm64: GICv4.1: Allow non-trapping WFI when using HW SGIs
...
Replace the kvm_x86_ops pointer in common x86 with an instance of the
struct to save one pointer dereference when invoking functions. Copy the
struct by value to set the ops during kvm_init().
Arbitrarily use kvm_x86_ops.hardware_enable to track whether or not the
ops have been initialized, i.e. a vendor KVM module has been loaded.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200321202603.19355-7-sean.j.christopherson@intel.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Tack on "used max basic" at the end of the CPUID tracepoint when the
output values correspond to the max basic leaf, i.e. when emulating
Intel's out-of-range CPUID behavior. Observing "cpuid entry not found"
in the tracepoint with non-zero output values is confusing for users
that aren't familiar with the out-of-range semantics, and qualifying the
"not found" case hopefully makes it clear that "found" means "found the
exact entry".
Suggested-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Output the requested index when tracing CPUID emulation; it's basically
mandatory for leafs where the index is meaningful, and is helpful for
verifying KVM correctness even when the index isn't meaningful, e.g. the
trace for a Linux guest's hypervisor_cpuid_base() probing appears to
be broken (returns all zeroes) at first glance, but is correct because
the index is non-zero, i.e. the output values correspond to a random
index in the maximum basic leaf.
Suggested-by: Xiaoyao Li <xiaoyao.li@intel.com>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
GA Log tracepoint is useful when debugging AVIC performance
issue as it can be used with perf to count the number of times
IOMMU AVIC injects interrupts through the slow-path instead of
directly inject interrupts to the target vcpu.
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Allocate the emulation context instead of embedding it in struct
kvm_vcpu_arch.
Dynamic allocation provides several benefits:
- Shrinks the size x86 vcpus by ~2.5k bytes, dropping them back below
the PAGE_ALLOC_COSTLY_ORDER threshold.
- Allows for dropping the include of kvm_emulate.h from asm/kvm_host.h
and moving kvm_emulate.h into KVM's private directory.
- Allows a reducing KVM's attack surface by shrinking the amount of
vCPU data that is exposed to usercopy.
- Allows a future patch to disable the emulator entirely, which may or
may not be a realistic endeavor.
Mark the entire struct as valid for usercopy to maintain existing
behavior with respect to hardened usercopy. Future patches can shrink
the usercopy range to cover only what is necessary.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use the recently added tracepoint for logging nested VM-Enter failures
instead of spamming the kernel log when hardware detects a consistency
check failure. Take the opportunity to print the name of the error code
instead of dumping the raw hex number, but limit the symbol table to
error codes that can reasonably be encountered by KVM.
Add an equivalent tracepoint in nested_vmx_check_vmentry_hw(), e.g. so
that tracing of "invalid control field" errors isn't suppressed when
nested early checks are enabled.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Debugging a failed VM-Enter is often like searching for a needle in a
haystack, e.g. there are over 80 consistency checks that funnel into
the "invalid control field" error code. One way to expedite debug is
to run the buggy code as an L1 guest under KVM (and pray that the
failing check is detected by KVM). However, extracting useful debug
information out of L0 KVM requires attaching a debugger to KVM and/or
modifying the source, e.g. to log which check is failing.
Make life a little less painful for VMM developers and add a tracepoint
for failed VM-Enter consistency checks. Ideally the tracepoint would
capture both what check failed and precisely why it failed, but logging
why a checked failed is difficult to do in a generic tracepoint without
resorting to invasive techniques, e.g. generating a custom string on
failure. That being said, for the vast majority of VM-Enter failures
the most difficult step is figuring out exactly what to look at, e.g.
figuring out which bit was incorrectly set in a control field is usually
not too painful once the guilty field as been identified.
To reach a happy medium between precision and ease of use, simply log
the code that detected a failed check, using a macro to execute the
check and log the trace event on failure. This approach enables tracing
arbitrary code, e.g. it's not limited to function calls or specific
formats of checks, and the changes to the existing code are minimally
invasive. A macro with a two-character name is desirable as usage of
the macro doesn't result in overly long lines or confusing alignment,
while still retaining some amount of readability. I.e. a one-character
name is a little too terse, and a three-character name results in the
contents being passed to the macro aligning with an indented line when
the macro is used an in if-statement, e.g.:
if (VCC(nested_vmx_check_long_line_one(...) &&
nested_vmx_check_long_line_two(...)))
return -EINVAL;
And that is the story of how the CC(), a.k.a. Consistency Check, macro
got its name.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The PLE window tracepoint triggers even if the window is not changed,
and the wording can be a bit confusing too. One example line:
kvm_ple_window: vcpu 0: ple_window 4096 (shrink 4096)
It easily let people think of "the window now is 4096 which is
shrinked", but the truth is the value actually didn't change (4096).
Let's only dump this message if the value really changed, and we make
the message even simpler like:
kvm_ple_window: vcpu 4 old 4096 new 8192 (growed)
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The VMX ple_window is 32 bits wide, so logically it can overflow with
an int. The module parameter is declared as unsigned int which is
good, however the dynamic variable is not. Switching all the
ple_window references to use unsigned int.
The tracepoint changes will also affect SVM, but SVM is using an even
smaller width (16 bits) so it's always fine.
Suggested-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Tracing the ID helps to pair vmenters and vmexits for guests with
multiple vCPUs.
Reviewed-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>