There are (atleast) two versions of the i.MX53 LOCO:
- the MCIMX53-START board
- the MCIMX53-START-R board
The MCIMX53-START-R has a mc34708 pmic and is otherwise the similar to the
MCIMX53-START. To prepare for the START-R, move all common nodes to a new
imx53-qsb-common.dtsi and remove everything but the board name and pmic from
the imx53-qsb.dts.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
imx53-evk board is discontinued by Freescale. The replacement is
imx53-qsb. Additionally this board is not supported by anyone and
in their current state is non-functional, for example PMIC not have
an IRQ line defined, so it is not works. This patch removes this DTS.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch uses the IRQ_TYPE_LEVEL_HIGH/IRQ_TYPE_NONE to replace
the hardcode.
[shawn.guo: While at it, we also fix the typo in uart0 interrupts
property, where the 0x00 should 0x04. Hense, it should also be
IRQ_TYPE_LEVEL_HIGH just like other UART instances.]
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This is to permit to use of the includes in the boards dts.
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: devicetree@vger.kernel.org
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds the missing (Synchronous Serial Interface) SSI1 & SSI2
devicetree nodes for i.MX27 CPUs.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
We need to use controller id to access different register regions
for mxs phy.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds pinctrl definitions for WEIM CS4 and GPIO used as
CAN IRQ line.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Since SPI core does not use GPIO bindings for CS GPIOs,
we should add an active high level declaration.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds pin group for NAND Flash Controller.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This allows to read the SoC on-die temperature sensor available on the LRADC by
using:
cat /sys/class/hwmon/hwmon0/device/temp1_input
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This allows to read the SoC on-die temperature sensor available on the LRADC by
using:
cat /sys/class/hwmon/hwmon0/device/temp1_input
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
PCM-038 module cannot be used standalone. This patch renames
module file to .dtsi and excludes it from compilation.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Adding #io-channel-cells property to lradc allows us to use the lradc as
an iio provider.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The pins have nothing todo with the phy layer. We better rename them, so
it gets clear they are routed to the ehci core not to any phy.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch changes the default direction for pins used
as GPIO to "input". This prevents a short circuit on the
configuration stage when GPIO-pin is connected to the
other output pin.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch updates FEC devicetree node of Phytec PCM038 module:
- Adding missing phy_mode properties.
- Adding fixed regulator to provide functionality without
dummy-regulator in the kernel.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds first I2C bus and PCA9536 device.
This device is used on Phytec PCM-970 RDK camera addon module.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds support for On Flash Bad Block Table for PCM-038
onboard NAND.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
It is safe to operate I2C0 at 400kHz as SGTL5000 supports this frequency.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
uart1 is not used on SOM. It is passed directly to the rdk board.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds a iomux node for imx27 pinctrl driver. The gpio
registers are embedded in the iomux memory area. So this patch moves
them into the iomux node for a better hardware description.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
usbphy0 is not a part of AIPS1, so move this node under root.
Additionally this patch removes useless "status" property.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This USB port is only used as peripheral. Set it accordingly in its DT
node.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The Crystalfontz CFA-10049 has 3 Nuvoton NAU7802 ADCs, plugged behing a
GPIO-controlled I2C muxer because these ADCs don't have a configurable
address.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add USB support for M53EVK. The configuration is such that USB Host1
port is used as Host and the USB OTG port is used as Peripheral thus
far. Once OTG is properly fixed, the OTG will be further adjusted.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Remove the PWM backlight pin from the hog pins list, so it doesn't
collide with the PWM pin group. Moreover, add dummy regulator for
the backlight so that the backlight driver probes correctly.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
