8 small fixes, all in drivers.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYKbXoCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishUpRAQDBm6al
eIw0PTxDE9YrlbjkjBAkbiV88D9/v69NlIpmdQD/fx0+6WK4CexzRoj+tiW5XaCz
3L2zPdTGrNVDwfqHV+s=
=GAee
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Eight small fixes, all in drivers"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: pm80xx: Fix drives missing during rmmod/insmod loop
scsi: qla2xxx: Fix error return code in qla82xx_write_flash_dword()
scsi: qedf: Add pointer checks in qedf_update_link_speed()
scsi: ufs: core: Increase the usable queue depth
scsi: BusLogic: Fix 64-bit system enumeration error for Buslogic
scsi: ufs: ufs-mediatek: Fix power down spec violation
When driver is loaded after rmmod some drives are not showing up during
discovery.
SATA drives are directly attached to the controller connected phys. During
device discovery, the IDENTIFY command (qc timeout (cmd 0xec)) is timing out
during revalidation. This will trigger abort from host side and controller
successfully aborts the command and returns success. Post this successful
abort response ATA library decides to mark the disk as NODEV.
To overcome this, inside pm8001_scan_start() after phy_start() call, add get
start response and wait for few milliseconds to trigger next phy start.
This millisecond delay will give sufficient time for the controller state
machine to accept next phy start.
Link: https://lore.kernel.org/r/20210505120103.24497-1-ajish.koshy@microchip.com
Signed-off-by: Ajish Koshy <ajish.koshy@microchip.com>
Signed-off-by: Viswas G <viswas.g@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix to return a negative error code from the error handling case instead of
0 as done elsewhere in this function.
Link: https://lore.kernel.org/r/20210514090952.6715-1-thunder.leizhen@huawei.com
Fixes: a9083016a5 ("[SCSI] qla2xxx: Add ISP82XX support.")
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With the current implementation of the UFS driver active_queues is 1
instead of 0 if all UFS request queues are idle. That causes
hctx_may_queue() to divide the queue depth by 2 when queueing a request and
hence reduces the usable queue depth.
The shared tag set code in the block layer keeps track of the number of
active request queues. blk_mq_tag_busy() is called before a request is
queued onto a hwq and blk_mq_tag_idle() is called some time after the hwq
became idle. blk_mq_tag_idle() is called from inside blk_mq_timeout_work().
Hence, blk_mq_tag_idle() is only called if a timer is associated with each
request that is submitted to a request queue that shares a tag set with
another request queue.
Adds a blk_mq_start_request() call in ufshcd_exec_dev_cmd(). This doubles
the queue depth on my test setup from 16 to 32.
In addition to increasing the usable queue depth, also fix the
documentation of the 'timeout' parameter in the header above
ufshcd_exec_dev_cmd().
Link: https://lore.kernel.org/r/20210513164912.5683-1-bvanassche@acm.org
Fixes: 7252a36030 ("scsi: ufs: Avoid busy-waiting by eliminating tag conflicts")
Cc: Can Guo <cang@codeaurora.org>
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Stanley Chu <stanley.chu@mediatek.com>
Cc: Bean Huo <beanhuo@micron.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 391e2f2560 ("[SCSI] BusLogic: Port driver to 64-bit")
introduced a serious issue for 64-bit systems. With this commit,
64-bit kernel will enumerate 8*15 non-existing disks. This is caused
by the broken CCB structure. The change from u32 data to void *data
increased CCB length on 64-bit system, which introduced an extra 4
byte offset of the CDB. This leads to incorrect response to INQUIRY
commands during enumeration.
Fix disk enumeration failure by reverting the portion of the commit
above which switched the data pointer from u32 to void.
Link: https://lore.kernel.org/r/C325637F-1166-4340-8F0F-3BCCD59D4D54@vmware.com
Acked-by: Khalid Aziz <khalid@gonehiking.org>
Signed-off-by: Matt Wang <wwentao@vmware.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As per spec, e.g. JESD220E chapter 7.2, while powering off the UFS device,
RST_N signal should be between VSS(Ground) and VCCQ/VCCQ2. The power down
sequence after fixing:
Power down:
1. Assert RST_N low
2. Turn-off VCC
3. Turn-off VCCQ/VCCQ2
Link: https://lore.kernel.org/r/1620813706-25331-1-git-send-email-peter.wang@mediatek.com
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Peter Wang <peter.wang@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Move ufshcd_set_variant call in ufs_hisi_init_common to common error
section at end of the function, and then jump to this from the error
checking statements for both devm_reset_control_get and
ufs_hisi_get_resource. This fixes the original commit (63a06181d7)
which was reverted due to the University of Minnesota problems.
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Link: https://lore.kernel.org/r/20210503115736.2104747-32-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 63a06181d7.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The original commit is incorrect, it does not properly clean up on the
error path, so I'll keep the revert and fix it up properly with a
follow-on patch.
Cc: Kangjie Lu <kjlu@umn.edu>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Fixes: 63a06181d7 ("scsi: ufs: fix a missing check of devm_reset_control_get")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-31-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a set of minor fixes in various drivers (qla2xxx, ufs,
scsi_debug, lpfc) one doc fix and a fairly large update to the fnic
driver to remove the open coded iteration functions in favour of the
scsi provided ones.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYJa23iYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishVhnAP0WVxjv
V+L6SAyssgzN3Nbq/nY18qMU1/yeA5jVljRW1gD+JaQKpkOmU+lsldauwW2a3v0G
9XPGTricrtYOu1j3t7c=
=F0aC
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"This is a set of minor fixes in various drivers (qla2xxx, ufs,
scsi_debug, lpfc) one doc fix and a fairly large update to the fnic
driver to remove the open coded iteration functions in favour of the
scsi provided ones"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: fnic: Use scsi_host_busy_iter() to traverse commands
scsi: fnic: Kill 'exclude_id' argument to fnic_cleanup_io()
scsi: scsi_debug: Fix cmd_per_lun, set to max_queue
scsi: ufs: core: Narrow down fast path in system suspend path
scsi: ufs: core: Cancel rpm_dev_flush_recheck_work during system suspend
scsi: ufs: core: Do not put UFS power into LPM if link is broken
scsi: qla2xxx: Prevent PRLI in target mode
scsi: qla2xxx: Add marginal path handling support
scsi: target: tcmu: Return from tcmu_handle_completions() if cmd_id not found
scsi: ufs: core: Fix a typo in ufs-sysfs.c
scsi: lpfc: Fix bad memory access during VPD DUMP mailbox command
scsi: lpfc: Fix DMA virtual address ptr assignment in bsg
scsi: lpfc: Fix illegal memory access on Abort IOCBs
scsi: blk-mq: Fix build warning when making htmldocs
The section "19) Editor modelines and other cruft" in
Documentation/process/coding-style.rst clearly says, "Do not include any
of these in source files."
I recently receive a patch to explicitly add a new one.
Let's do treewide cleanups, otherwise some people follow the existing code
and attempt to upstream their favoriate editor setups.
It is even nicer if scripts/checkpatch.pl can check it.
If we like to impose coding style in an editor-independent manner, I think
editorconfig (patch [1]) is a saner solution.
[1] https://lore.kernel.org/lkml/20200703073143.423557-1-danny@kdrag0n.dev/
Link: https://lkml.kernel.org/r/20210324054457.1477489-1-masahiroy@kernel.org
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org> [auxdisplay]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
My UEK-derived config has 1030 files depending on pagemap.h before this
change. Afterwards, just 326 files need to be rebuilt when I touch
pagemap.h. I think blkdev.h is probably included too widely, but
untangling that dependency is harder and this solves my problem. x86
allmodconfig builds, but there may be implicit include problems on other
architectures.
Link: https://lkml.kernel.org/r/20210309195747.283796-1-willy@infradead.org
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Acked-by: Dan Williams <dan.j.williams@intel.com> [nvdimm]
Acked-by: Jens Axboe <axboe@kernel.dk> [block]
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Coly Li <colyli@suse.de> [bcache]
Acked-by: Martin K. Petersen <martin.petersen@oracle.com> [scsi]
Reviewed-by: William Kucharski <william.kucharski@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that proc_ops are separate from file_operations and other operations
it easy to check all instances to have ->proc_lseek hook and remove check
in main code.
Note:
nonseekable_open() files naturally don't require ->proc_lseek.
Garbage collect pde_lseek() function.
[adobriyan@gmail.com: smoke test lseek()]
Link: https://lkml.kernel.org/r/YG4OIhChOrVTPgdN@localhost.localdomain
Link: https://lkml.kernel.org/r/YFYX0Bzwxlc7aBa/@localhost.localdomain
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use scsi_host_busy_iter() to traverse commands instead of hand-crafted
routines walking the command list.
Link: https://lore.kernel.org/r/20210429122517.39659-3-hare@suse.de
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
'exclude_id' is always SCSI_NO_TAG which will never be reached when
traversing the list of tags.
Link: https://lore.kernel.org/r/20210429122517.39659-2-hare@suse.de
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make sure that the cmd_per_lun value placed in the host template never
exceeds the can_queue value. If the max_queue driver parameter is not
specified then both cmd_per_lun and can_queue are set to CAN_QUEUE.
CAN_QUEUE is a compile time constant and is used to dimension an array to
hold queued requests. If the max_queue driver parameter is given it is must
be less than or equal to CAN_QUEUE and if so, the host template values are
adjusted.
Remove undocumented code that allowed queue_depth to exceed CAN_QUEUE and
cause stack full type errors. There is a documented way to do that with
every_nth and
echo 0x8000 > /sys/bus/pseudo/drivers/scsi_debug/opts
See: https://sg.danny.cz/sg/scsi_debug.html
Tweak some formatting, and add a suggestion to the "trim poll_queues"
warning.
Link: https://lore.kernel.org/r/20210415015031.607153-1-dgilbert@interlog.com
Reported-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: John Garry <john.garry@hauwei.com>
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
All callers pass 0 as offset. Therefore remove the parameter and use a
fixed offset 0 in pci_vpd_find_tag().
Link: https://lore.kernel.org/r/f62e6e19-5423-2ead-b2bd-62844b23ef8f@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Core:
- bpf:
- allow bpf programs calling kernel functions (initially to
reuse TCP congestion control implementations)
- enable task local storage for tracing programs - remove the
need to store per-task state in hash maps, and allow tracing
programs access to task local storage previously added for
BPF_LSM
- add bpf_for_each_map_elem() helper, allowing programs to
walk all map elements in a more robust and easier to verify
fashion
- sockmap: support UDP and cross-protocol BPF_SK_SKB_VERDICT
redirection
- lpm: add support for batched ops in LPM trie
- add BTF_KIND_FLOAT support - mostly to allow use of BTF
on s390 which has floats in its headers files
- improve BPF syscall documentation and extend the use of kdoc
parsing scripts we already employ for bpf-helpers
- libbpf, bpftool: support static linking of BPF ELF files
- improve support for encapsulation of L2 packets
- xdp: restructure redirect actions to avoid a runtime lookup,
improving performance by 4-8% in microbenchmarks
- xsk: build skb by page (aka generic zerocopy xmit) - improve
performance of software AF_XDP path by 33% for devices
which don't need headers in the linear skb part (e.g. virtio)
- nexthop: resilient next-hop groups - improve path stability
on next-hops group changes (incl. offload for mlxsw)
- ipv6: segment routing: add support for IPv4 decapsulation
- icmp: add support for RFC 8335 extended PROBE messages
- inet: use bigger hash table for IP ID generation
- tcp: deal better with delayed TX completions - make sure we don't
give up on fast TCP retransmissions only because driver is
slow in reporting that it completed transmitting the original
- tcp: reorder tcp_congestion_ops for better cache locality
- mptcp:
- add sockopt support for common TCP options
- add support for common TCP msg flags
- include multiple address ids in RM_ADDR
- add reset option support for resetting one subflow
- udp: GRO L4 improvements - improve 'forward' / 'frag_list'
co-existence with UDP tunnel GRO, allowing the first to take
place correctly even for encapsulated UDP traffic
- micro-optimize dev_gro_receive() and flow dissection, avoid
retpoline overhead on VLAN and TEB GRO
- use less memory for sysctls, add a new sysctl type, to allow using
u8 instead of "int" and "long" and shrink networking sysctls
- veth: allow GRO without XDP - this allows aggregating UDP
packets before handing them off to routing, bridge, OvS, etc.
- allow specifing ifindex when device is moved to another namespace
- netfilter:
- nft_socket: add support for cgroupsv2
- nftables: add catch-all set element - special element used
to define a default action in case normal lookup missed
- use net_generic infra in many modules to avoid allocating
per-ns memory unnecessarily
- xps: improve the xps handling to avoid potential out-of-bound
accesses and use-after-free when XPS change race with other
re-configuration under traffic
- add a config knob to turn off per-cpu netdev refcnt to catch
underflows in testing
Device APIs:
- add WWAN subsystem to organize the WWAN interfaces better and
hopefully start driving towards more unified and vendor-
-independent APIs
- ethtool:
- add interface for reading IEEE MIB stats (incl. mlx5 and
bnxt support)
- allow network drivers to dump arbitrary SFP EEPROM data,
current offset+length API was a poor fit for modern SFP
which define EEPROM in terms of pages (incl. mlx5 support)
- act_police, flow_offload: add support for packet-per-second
policing (incl. offload for nfp)
- psample: add additional metadata attributes like transit delay
for packets sampled from switch HW (and corresponding egress
and policy-based sampling in the mlxsw driver)
- dsa: improve support for sandwiched LAGs with bridge and DSA
- netfilter:
- flowtable: use direct xmit in topologies with IP
forwarding, bridging, vlans etc.
- nftables: counter hardware offload support
- Bluetooth:
- improvements for firmware download w/ Intel devices
- add support for reading AOSP vendor capabilities
- add support for virtio transport driver
- mac80211:
- allow concurrent monitor iface and ethernet rx decap
- set priority and queue mapping for injected frames
- phy: add support for Clause-45 PHY Loopback
- pci/iov: add sysfs MSI-X vector assignment interface
to distribute MSI-X resources to VFs (incl. mlx5 support)
New hardware/drivers:
- dsa: mv88e6xxx: add support for Marvell mv88e6393x -
11-port Ethernet switch with 8x 1-Gigabit Ethernet
and 3x 10-Gigabit interfaces.
- dsa: support for legacy Broadcom tags used on BCM5325, BCM5365
and BCM63xx switches
- Microchip KSZ8863 and KSZ8873; 3x 10/100Mbps Ethernet switches
- ath11k: support for QCN9074 a 802.11ax device
- Bluetooth: Broadcom BCM4330 and BMC4334
- phy: Marvell 88X2222 transceiver support
- mdio: add BCM6368 MDIO mux bus controller
- r8152: support RTL8153 and RTL8156 (USB Ethernet) chips
- mana: driver for Microsoft Azure Network Adapter (MANA)
- Actions Semi Owl Ethernet MAC
- can: driver for ETAS ES58X CAN/USB interfaces
Pure driver changes:
- add XDP support to: enetc, igc, stmmac
- add AF_XDP support to: stmmac
- virtio:
- page_to_skb() use build_skb when there's sufficient tailroom
(21% improvement for 1000B UDP frames)
- support XDP even without dedicated Tx queues - share the Tx
queues with the stack when necessary
- mlx5:
- flow rules: add support for mirroring with conntrack,
matching on ICMP, GTP, flex filters and more
- support packet sampling with flow offloads
- persist uplink representor netdev across eswitch mode
changes
- allow coexistence of CQE compression and HW time-stamping
- add ethtool extended link error state reporting
- ice, iavf: support flow filters, UDP Segmentation Offload
- dpaa2-switch:
- move the driver out of staging
- add spanning tree (STP) support
- add rx copybreak support
- add tc flower hardware offload on ingress traffic
- ionic:
- implement Rx page reuse
- support HW PTP time-stamping
- octeon: support TC hardware offloads - flower matching on ingress
and egress ratelimitting.
- stmmac:
- add RX frame steering based on VLAN priority in tc flower
- support frame preemption (FPE)
- intel: add cross time-stamping freq difference adjustment
- ocelot:
- support forwarding of MRP frames in HW
- support multiple bridges
- support PTP Sync one-step timestamping
- dsa: mv88e6xxx, dpaa2-switch: offload bridge port flags like
learning, flooding etc.
- ipa: add IPA v4.5, v4.9 and v4.11 support (Qualcomm SDX55, SM8350,
SC7280 SoCs)
- mt7601u: enable TDLS support
- mt76:
- add support for 802.3 rx frames (mt7915/mt7615)
- mt7915 flash pre-calibration support
- mt7921/mt7663 runtime power management fixes
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=vcbA
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- bpf:
- allow bpf programs calling kernel functions (initially to
reuse TCP congestion control implementations)
- enable task local storage for tracing programs - remove the
need to store per-task state in hash maps, and allow tracing
programs access to task local storage previously added for
BPF_LSM
- add bpf_for_each_map_elem() helper, allowing programs to walk
all map elements in a more robust and easier to verify fashion
- sockmap: support UDP and cross-protocol BPF_SK_SKB_VERDICT
redirection
- lpm: add support for batched ops in LPM trie
- add BTF_KIND_FLOAT support - mostly to allow use of BTF on
s390 which has floats in its headers files
- improve BPF syscall documentation and extend the use of kdoc
parsing scripts we already employ for bpf-helpers
- libbpf, bpftool: support static linking of BPF ELF files
- improve support for encapsulation of L2 packets
- xdp: restructure redirect actions to avoid a runtime lookup,
improving performance by 4-8% in microbenchmarks
- xsk: build skb by page (aka generic zerocopy xmit) - improve
performance of software AF_XDP path by 33% for devices which don't
need headers in the linear skb part (e.g. virtio)
- nexthop: resilient next-hop groups - improve path stability on
next-hops group changes (incl. offload for mlxsw)
- ipv6: segment routing: add support for IPv4 decapsulation
- icmp: add support for RFC 8335 extended PROBE messages
- inet: use bigger hash table for IP ID generation
- tcp: deal better with delayed TX completions - make sure we don't
give up on fast TCP retransmissions only because driver is slow in
reporting that it completed transmitting the original
- tcp: reorder tcp_congestion_ops for better cache locality
- mptcp:
- add sockopt support for common TCP options
- add support for common TCP msg flags
- include multiple address ids in RM_ADDR
- add reset option support for resetting one subflow
- udp: GRO L4 improvements - improve 'forward' / 'frag_list'
co-existence with UDP tunnel GRO, allowing the first to take place
correctly even for encapsulated UDP traffic
- micro-optimize dev_gro_receive() and flow dissection, avoid
retpoline overhead on VLAN and TEB GRO
- use less memory for sysctls, add a new sysctl type, to allow using
u8 instead of "int" and "long" and shrink networking sysctls
- veth: allow GRO without XDP - this allows aggregating UDP packets
before handing them off to routing, bridge, OvS, etc.
- allow specifing ifindex when device is moved to another namespace
- netfilter:
- nft_socket: add support for cgroupsv2
- nftables: add catch-all set element - special element used to
define a default action in case normal lookup missed
- use net_generic infra in many modules to avoid allocating
per-ns memory unnecessarily
- xps: improve the xps handling to avoid potential out-of-bound
accesses and use-after-free when XPS change race with other
re-configuration under traffic
- add a config knob to turn off per-cpu netdev refcnt to catch
underflows in testing
Device APIs:
- add WWAN subsystem to organize the WWAN interfaces better and
hopefully start driving towards more unified and vendor-
independent APIs
- ethtool:
- add interface for reading IEEE MIB stats (incl. mlx5 and bnxt
support)
- allow network drivers to dump arbitrary SFP EEPROM data,
current offset+length API was a poor fit for modern SFP which
define EEPROM in terms of pages (incl. mlx5 support)
- act_police, flow_offload: add support for packet-per-second
policing (incl. offload for nfp)
- psample: add additional metadata attributes like transit delay for
packets sampled from switch HW (and corresponding egress and
policy-based sampling in the mlxsw driver)
- dsa: improve support for sandwiched LAGs with bridge and DSA
- netfilter:
- flowtable: use direct xmit in topologies with IP forwarding,
bridging, vlans etc.
- nftables: counter hardware offload support
- Bluetooth:
- improvements for firmware download w/ Intel devices
- add support for reading AOSP vendor capabilities
- add support for virtio transport driver
- mac80211:
- allow concurrent monitor iface and ethernet rx decap
- set priority and queue mapping for injected frames
- phy: add support for Clause-45 PHY Loopback
- pci/iov: add sysfs MSI-X vector assignment interface to distribute
MSI-X resources to VFs (incl. mlx5 support)
New hardware/drivers:
- dsa: mv88e6xxx: add support for Marvell mv88e6393x - 11-port
Ethernet switch with 8x 1-Gigabit Ethernet and 3x 10-Gigabit
interfaces.
- dsa: support for legacy Broadcom tags used on BCM5325, BCM5365 and
BCM63xx switches
- Microchip KSZ8863 and KSZ8873; 3x 10/100Mbps Ethernet switches
- ath11k: support for QCN9074 a 802.11ax device
- Bluetooth: Broadcom BCM4330 and BMC4334
- phy: Marvell 88X2222 transceiver support
- mdio: add BCM6368 MDIO mux bus controller
- r8152: support RTL8153 and RTL8156 (USB Ethernet) chips
- mana: driver for Microsoft Azure Network Adapter (MANA)
- Actions Semi Owl Ethernet MAC
- can: driver for ETAS ES58X CAN/USB interfaces
Pure driver changes:
- add XDP support to: enetc, igc, stmmac
- add AF_XDP support to: stmmac
- virtio:
- page_to_skb() use build_skb when there's sufficient tailroom
(21% improvement for 1000B UDP frames)
- support XDP even without dedicated Tx queues - share the Tx
queues with the stack when necessary
- mlx5:
- flow rules: add support for mirroring with conntrack, matching
on ICMP, GTP, flex filters and more
- support packet sampling with flow offloads
- persist uplink representor netdev across eswitch mode changes
- allow coexistence of CQE compression and HW time-stamping
- add ethtool extended link error state reporting
- ice, iavf: support flow filters, UDP Segmentation Offload
- dpaa2-switch:
- move the driver out of staging
- add spanning tree (STP) support
- add rx copybreak support
- add tc flower hardware offload on ingress traffic
- ionic:
- implement Rx page reuse
- support HW PTP time-stamping
- octeon: support TC hardware offloads - flower matching on ingress
and egress ratelimitting.
- stmmac:
- add RX frame steering based on VLAN priority in tc flower
- support frame preemption (FPE)
- intel: add cross time-stamping freq difference adjustment
- ocelot:
- support forwarding of MRP frames in HW
- support multiple bridges
- support PTP Sync one-step timestamping
- dsa: mv88e6xxx, dpaa2-switch: offload bridge port flags like
learning, flooding etc.
- ipa: add IPA v4.5, v4.9 and v4.11 support (Qualcomm SDX55, SM8350,
SC7280 SoCs)
- mt7601u: enable TDLS support
- mt76:
- add support for 802.3 rx frames (mt7915/mt7615)
- mt7915 flash pre-calibration support
- mt7921/mt7663 runtime power management fixes"
* tag 'net-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2451 commits)
net: selftest: fix build issue if INET is disabled
net: netrom: nr_in: Remove redundant assignment to ns
net: tun: Remove redundant assignment to ret
net: phy: marvell: add downshift support for M88E1240
net: dsa: ksz: Make reg_mib_cnt a u8 as it never exceeds 255
net/sched: act_ct: Remove redundant ct get and check
icmp: standardize naming of RFC 8335 PROBE constants
bpf, selftests: Update array map tests for per-cpu batched ops
bpf: Add batched ops support for percpu array
bpf: Implement formatted output helpers with bstr_printf
seq_file: Add a seq_bprintf function
sfc: adjust efx->xdp_tx_queue_count with the real number of initialized queues
net:nfc:digital: Fix a double free in digital_tg_recv_dep_req
net: fix a concurrency bug in l2tp_tunnel_register()
net/smc: Remove redundant assignment to rc
mpls: Remove redundant assignment to err
llc2: Remove redundant assignment to rc
net/tls: Remove redundant initialization of record
rds: Remove redundant assignment to nr_sig
dt-bindings: net: mdio-gpio: add compatible for microchip,mdio-smi0
...
If spm_lvl is set to 0 or 1, when system suspend kicks start and HBA is
runtime active, system suspend may just bail without doing anything (the
fast path), leaving other contexts still running, e.g., clock gating and
clock scaling. When system resume kicks start, concurrency can happen
between ufshcd_resume() and these contexts, leading to various stability
issues.
Add a check against HBA's runtime state and allowing fast path only if HBA
is runtime suspended, otherwise let system suspend go ahead call
ufshcd_suspend(). This will guarantee that these contexts are stopped by
either runtime suspend or system suspend.
Link: https://lore.kernel.org/r/1619408921-30426-4-git-send-email-cang@codeaurora.org
Fixes: 0b25773434 ("scsi: ufs: optimize system suspend handling")
Reviewed-by: Daejun Park <daejun7.park@samsung.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During ufs system suspend, leaving rpm_dev_flush_recheck_work running or
pending is risky because concurrency may happen between system
suspend/resume and runtime resume routine. Fix this by cancelling
rpm_dev_flush_recheck_work synchronously during system suspend.
Link: https://lore.kernel.org/r/1619408921-30426-3-git-send-email-cang@codeaurora.org
Fixes: 51dd905bd2 ("scsi: ufs: Fix WriteBooster flush during runtime suspend")
Reviewed-by: Daejun Park <daejun7.park@samsung.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During resume, if link is broken due to AH8 failure, make sure
ufshcd_resume() does not put UFS power back into LPM.
Link: https://lore.kernel.org/r/1619408921-30426-2-git-send-email-cang@codeaurora.org
Fixes: 4db7a23605 ("scsi: ufs: Fix concurrency of error handler and other error recovery paths")
Reviewed-by: Daejun Park <daejun7.park@samsung.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In a case when the initiator in P2P mode by some circumstances does not
send PRLI, the target, in a case when the target port's WWPN is less than
initiator's, changes the discovery state in DSC_GNL. When gnl completes it
sends PRLI to the initiator.
Usually the initiator in P2P mode always sends PRLI. We caught this issue
on Linux stable v5.4.6 https://www.spinics.net/lists/stable/msg458515.html.
Fix this particular corner case in the behaviour of the P2P mod target
login state machine.
Link: https://lore.kernel.org/r/20210422153414.4022-1-a.kovaleva@yadro.com
Fixes: a9ed06d4e6 ("scsi: qla2xxx: Allow PLOGI in target mode")
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Anastasia Kovaleva <a.kovaleva@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix the following typo:
ufschd_uic_link_state_to_string() -> ufshcd_uic_link_state_to_string()
ufschd_ufs_dev_pwr_mode_to_string() -> ufshcd_ufs_dev_pwr_mode_to_string()
Link: https://lore.kernel.org/r/1381713434.61619509208911.JavaMail.epsvc@epcpadp3
Signed-off-by: Keoseong Park <keosung.park@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This series consists of the usual driver updates (ufs, target, tcmu,
smartpqi, lpfc, zfcp, qla2xxx, mpt3sas, pm80xx). The major core
change is using a sbitmap instead of an atomic for queue tracking.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYInvqCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishYh2AP0SgqqL
WYZRT2oiyBOKD28v+ceOSiXvgjPlqABwVMC0BAEAn29/wNCxyvzZ1k/b0iPJ4M+S
klkSxLzXKQLzJBgdK5w=
=p5B/
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This consists of the usual driver updates (ufs, target, tcmu,
smartpqi, lpfc, zfcp, qla2xxx, mpt3sas, pm80xx).
The major core change is using a sbitmap instead of an atomic for
queue tracking"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (412 commits)
scsi: target: tcm_fc: Fix a kernel-doc header
scsi: target: Shorten ALUA error messages
scsi: target: Fix two format specifiers
scsi: target: Compare explicitly with SAM_STAT_GOOD
scsi: sd: Introduce a new local variable in sd_check_events()
scsi: dc395x: Open-code status_byte(u8) calls
scsi: 53c700: Open-code status_byte(u8) calls
scsi: smartpqi: Remove unused functions
scsi: qla4xxx: Remove an unused function
scsi: myrs: Remove unused functions
scsi: myrb: Remove unused functions
scsi: mpt3sas: Fix two kernel-doc headers
scsi: fcoe: Suppress a compiler warning
scsi: libfc: Fix a format specifier
scsi: aacraid: Remove an unused function
scsi: core: Introduce enum scsi_disposition
scsi: core: Modify the scsi_send_eh_cmnd() return value for the SDEV_BLOCK case
scsi: core: Rename scsi_softirq_done() into scsi_complete()
scsi: core: Remove an incorrect comment
scsi: core: Make the scsi_alloc_sgtables() documentation more accurate
...
The dump command for reading a region passes a requested read length
specified in words (4-byte units). The response overwrites the same field
with the actual number of bytes read.
The mailbox handler for DUMP which reads VPD data (region 23) is treating
the response field as if it were still a word_cnt, thus multiplying it by 4
to set the read's "length". Given the read value was calculated based on
the size of the read buffer, the longer response length runs off the end of
the buffer.
Fix by reworking the code to use the response field as a byte count.
Link: https://lore.kernel.org/r/20210421234511.102206-1-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
lpfc_bsg_ct_unsol_event() routine acts assigns a ct_request to the wrong
structure address, resulting in a bad address that results in bsg related
timeouts.
Correct the ct_request assignment to use the kernel virtual buffer address
(not the control structure address).
Link: https://lore.kernel.org/r/20210421234448.102132-1-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In devloss timer handler and in backend calls to terminate remote port I/O,
there is logic to walk through all active IOCBs and validate them to
potentially trigger an abort request. This logic is causing illegal memory
accesses which leads to a crash. Abort IOCBs, which may be on the list, do
not have an associated lpfc_io_buf struct. The driver is trying to map an
lpfc_io_buf struct on the IOCB and which results in a bogus address thus
the issue.
Fix by skipping over ABORT IOCBs (CLOSE IOCBs are ABORTS that don't send
ABTS) in the IOCB scan logic.
Link: https://lore.kernel.org/r/20210421234433.102079-1-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This libsas fix is for a problem that occurs when trying to change the
cache type of an ATA device and the libiscsi one is a regression fix
from this merge window.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYHuPRSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pisha52AQCXc8n0
6VAjfc+8aCqjX2Hpw4YCGeW5RYoNj1WXhiDv/AD+L4FVBMdQ4DE9ukH12YW7YBRS
qP03aNSHLCl8wfVon8Q=
=Btn4
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two fixes: the libsas fix is for a problem that occurs when trying to
change the cache type of an ATA device and the libiscsi one is a
regression fix from this merge window"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: libsas: Reset num_scatter if libata marks qc as NODATA
scsi: iscsi: Fix iSCSI cls conn state
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
- keep the ZC code, drop the code related to reinit
net/bridge/netfilter/ebtables.c
- fix build after move to net_generic
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Instead of using 'retval' to represent first a SCSI status and later
whether or not a disk change event occurred, introduce a new variable for
the latter purpose.
Link: https://lore.kernel.org/r/20210415220826.29438-17-bvanassche@acm.org
Cc: Christoph Hellwig <hch@lst.de>
Cc: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The dc395x driver is one of the two drivers that passes an u8 argument to
status_byte() instead of an s32 argument. Open-code status_byte() in
preparation of changing SCSI status values into a structure.
Link: https://lore.kernel.org/r/20210415220826.29438-16-bvanassche@acm.org
Cc: Hannes Reinecke <hare@suse.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The 53c700 driver is one of the two drivers that passes an u8 argument to
status_byte() instead of an s32 argument. Open-code status_byte in
preparation of changing SCSI status values into a structure.
Link: https://lore.kernel.org/r/20210415220826.29438-15-bvanassche@acm.org
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This was detected by building the kernel with clang and W=1.
Link: https://lore.kernel.org/r/20210415220826.29438-14-bvanassche@acm.org
Cc: Don Brace <don.brace@microchip.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This was detected by building the kernel with clang and W=1.
Link: https://lore.kernel.org/r/20210415220826.29438-13-bvanassche@acm.org
Cc: Nilesh Javali <njavali@marvell.com>
Acked-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This was detected by building the kernel with clang and W=1.
Link: https://lore.kernel.org/r/20210415220826.29438-12-bvanassche@acm.org
Cc: Hannes Reinecke <hare@kernel.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This was detected by building the kernel with clang and W=1.
Link: https://lore.kernel.org/r/20210415220826.29438-11-bvanassche@acm.org
Cc: Hannes Reinecke <hare@kernel.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix the following warnings:
drivers/scsi/mpt3sas/mpt3sas_base.c:5430: warning: Excess function parameter 'ct' description in '_base_allocate_pcie_sgl_pool'
drivers/scsi/mpt3sas/mpt3sas_base.c:5493: warning: Excess function parameter 'ctr' description in '_base_allocate_chain_dma_pool'
Link: https://lore.kernel.org/r/20210415220826.29438-10-bvanassche@acm.org
Fixes: d6adc251dd ("scsi: mpt3sas: Force PCIe scatterlist allocations to be within same 4 GB region")
Fixes: 7dd847dae1 ("scsi: mpt3sas: Force chain buffer allocations to be within same 4 GB region")
Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Suppress the following compiler warning:
warning: cast to smaller integer type
'enum fip_mode' from 'void *' [-Wvoid-pointer-to-enum-cast]
enum fip_mode fip_mode = (enum fip_mode)kp->arg;
^~~~~~~~~~~~~~~~~~~~~~
Link: https://lore.kernel.org/r/20210415220826.29438-9-bvanassche@acm.org
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since the 'mfs' member has been declared as 'u32' in include/scsi/libfc.h,
use the %u format specifier instead of %hu. This patch fixes the following
clang compiler warning:
warning: format specifies type
'unsigned short' but the argument has type 'u32' (aka 'unsigned int')
[-Wformat]
"lport->mfs:%hu\n", mfs, lport->mfs);
~~~ ^~~~~~~~~~
%u
Link: https://lore.kernel.org/r/20210415220826.29438-8-bvanassche@acm.org
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Improve readability of the code in the SCSI core by introducing an
enumeration type for the values used internally that decide how to continue
processing a SCSI command. The eh_*_handler return values have not been
changed because that would involve modifying all SCSI drivers.
The output of the following command has been inspected to verify that no
out-of-range values are assigned to a variable of type enum
scsi_disposition:
KCFLAGS=-Wassign-enum make CC=clang W=1 drivers/scsi/
Link: https://lore.kernel.org/r/20210415220826.29438-6-bvanassche@acm.org
Cc: Christoph Hellwig <hch@lst.de>
Cc: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The comment above scsi_send_eh_cmnd() says: "Returns SUCCESS or FAILED or
NEEDS_RETRY". This patch makes all values returned by scsi_send_eh_cmnd()
match the documentation of this function. This change does not affect the
behavior of scsi_eh_tur() nor of scsi_eh_try_stu() nor of the
scsi_request_sense() callers.
See also commit bbe9fb0d04 ("scsi: Avoid that .queuecommand() gets called
for a blocked SCSI device"; v5.3).
Link: https://lore.kernel.org/r/20210415220826.29438-5-bvanassche@acm.org
Cc: Christoph Hellwig <hch@lst.de>
Cc: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 320ae51fee ("blk-mq: new multi-queue block IO queueing mechanism";
v3.13) introduced a code path that calls the blk-mq completion function
from interrupt context. scsi-mq was introduced by commit d285203cf6
("scsi: add support for a blk-mq based I/O path."; v3.17).
Since the introduction of scsi-mq, scsi_softirq_done() can be called from
interrupt context. That made the name of the function misleading, rename it
to scsi_complete().
Link: https://lore.kernel.org/r/20210415220826.29438-4-bvanassche@acm.org
Cc: Christoph Hellwig <hch@lst.de>
Cc: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The current scsi_alloc_sgtables() documentation does not accurately explain
what this function does. Hence improve the documentation of this function.
Link: https://lore.kernel.org/r/20210415220826.29438-2-bvanassche@acm.org
Cc: Christoph Hellwig <hch@lst.de>
Cc: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Introduce spin lock for outbound queue. With this, driver need not acquire
HBA global lock for outbound queue processing.
Link: https://lore.kernel.org/r/20210415103352.3580-9-Viswas.G@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Ruksar Devadi <Ruksar.devadi@microchip.com>
Signed-off-by: Ashokkumar N <Ashokkumar.N@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Producer index(PI) outbound queue and consumer index(CI) for Outbound queue
are in DMA memory. During resume(), the stale PI and CI Values will lead to
unexpected behavior. These values should be reset to 0 during driver
reinitialization.
Link: https://lore.kernel.org/r/20210415103352.3580-8-Viswas.G@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Ruksar Devadi <Ruksar.devadi@microchip.com>
Signed-off-by: Ashokkumar N <Ashokkumar.N@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
