There are some MAC registers that need to be kept in sync
with the link state parameters, see adjust_link().
However, after a MAC soft reset default values for
these registers are assumed. In some cases (excepting
if down/ if up for example) adjust_link() does not see
that these values were reset to default because the
priv->old* link parameters were left unchanged.
So, reset the priv->old* link params as well during a
MAC reset to let adjust_link() restore the MAC link
settings to the actual link state values.
Fixes following case, for example:
Setting link to 100M, changing MTU (implies MAC reset),
link state remains unchanged to 100M but MAC registers
were reset to default (1G) breaking the connectivity w/
the PHY. Closing and re-opening the interface would
restore the MAC link parameters to the correct values.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When generating /proc/net/route we emit a header followed by a line for
each route. When a short read is performed we will restart this process
based on the open file descriptor. When calculating the start point we
fail to take into account that the 0th entry is the header. This leads
us to skip the first entry when doing a continuation read.
This can be easily seen with the comparison below:
while read l; do echo "$l"; done </proc/net/route >A
cat /proc/net/route >B
diff -bu A B | grep '^[+-]'
On my example machine I have approximatly 10KB of route output. There we
see the very first non-title element is lost in the while read case,
and an entry around the 8K mark in the cat case:
+wlan0 00000000 02021EAC 0003 0 0 400 00000000 0 0 0
-tun1 00C0AC0A 00000000 0001 0 0 950 00C0FFFF 0 0 0
Fix up the off-by-one when reaquiring position on continuation.
Fixes: 8be33e955c ("fib_trie: Fib walk rcu should take a tnode and key instead of a trie and a leaf")
BugLink: http://bugs.launchpad.net/bugs/1483440
Acked-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent refactoring of the IGMP and MLD parsing code into
ipv6_mc_check_mld() / ip_mc_check_igmp() introduced a potential crash /
BUG() invocation for bridges:
I wrongly assumed that skb_get() could be used as a simple reference
counter for an skb which is not the case. skb_get() bears additional
semantics, a user count. This leads to a BUG() invocation in
pskb_expand_head() / kernel panic if pskb_may_pull() is called on an skb
with a user count greater than one - unfortunately the refactoring did
just that.
Fixing this by removing the skb_get() call and changing the API: The
caller of ipv6_mc_check_mld() / ip_mc_check_igmp() now needs to
additionally check whether the returned skb_trimmed is a clone.
Fixes: 9afd85c9e4 ("net: Export IGMP/MLD message validation code")
Reported-by: Brenden Blanco <bblanco@plumgrid.com>
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 1addc12648
This commit seems to cause crashes in gk104_fifo_intr_runlist() by
returning 0xbad0da00 when register 0x2a00 is read. Since this commit was
intended for GM20B which is not completely supported yet, let's revert
it for the time being.
Reported-by: Eric Biggers <ebiggers3@gmail.com>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Tested-by: Afzal Mohammed <afzal.mohd.ma@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This addresses two issues that cause problems with viewperf maya-03 in
situation with memory pressure.
The first issue causes attempts to unreserve buffers if batched
reservation fails due to, for example, a signal pending. While previously
the ttm_eu api was resistant against this type of error, it is no longer
and the lockdep code will complain about attempting to unreserve buffers
that are not reserved. The issue is resolved by avoid calling
ttm_eu_backoff_reservation in the buffer reserve error path.
The second issue is that the binding_mutex may be held when user-space
fence objects are created and hence during memory reclaims. This may cause
recursive attempts to grab the binding mutex. The issue is resolved by not
holding the binding mutex across fence creation and submission.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Pull ARM fixes from Russell King:
"Another few small ARM fixes, mostly addressing some VDSO issues"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8410/1: VDSO: fix coarse clock monotonicity regression
ARM: 8409/1: Mark ret_fast_syscall as a function
ARM: 8408/1: Fix the secondary_startup function in Big Endian case
ARM: 8405/1: VDSO: fix regression with toolchains lacking ld.bfd executable
Commit 3f5159a922 ("x86/asm/entry/32: Update -ENOSYS handling to match
the 64-bit logic") broke the ENOSYS handling for the 32-bit compat case.
The proper error return value was never loaded into %rax, except if
things just happened to go through the audit paths, which ended up
reloading the return value.
This moves the loading or %rax into the normal system call path, just to
make sure the error case triggers it. It's kind of sad, since it adds a
useless instruction to reload the register to the fast path, but it's
not like that single load from the stack is going to be noticeable.
Reported-by: David Drysdale <drysdale@google.com>
Tested-by: Kees Cook <keescook@chromium.org>
Acked-by: Andy Lutomirski <luto@amacapital.net>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
metadata snapshots aren't widely used but help provide a consistent
view of the metadata associated with an active thin-pool.
- a dm-cache fix for the 4.2 "default" policy switch from "mq" to "smq"
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVzPl/AAoJEMUj8QotnQNa2MUH/24BKs8WYNy79B9pr6H41ouQ
LAXFVfx3Vy7n3U1KrZcPylXb7R0feXphUrSXJ6ZlKz/Df+AhG5ycUOCfSZxSDpA9
pX5rtWFSWLXGF3wRf0GXqB3CXkrMKlNWVAUlzge39TpIzpdkbh9reM9He4yQphl9
u0QVvIOTQsUrtN9htnQb7Dgmm7qD6NinrebOrWTiOqBdCh3Iw4J48RsYggYOG0ZP
fbMnpZlH537vgLyKaz72Xh+kMrYmP5DBd1f+iAUBVKk12HQVQNMzEwOgkEB0M+4l
EG3c4O3zMVrBxXdxsI2srFZfLX2XeUYAuMx8cfVSSCDEzQwjC0kmXVdkCYuAjAk=
=r/53
-----END PGP SIGNATURE-----
Merge tag 'dm-4.2-fixes-5' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- two stable fixes for corruption seen in a snapshot of thinp metadata;
metadata snapshots aren't widely used but help provide a consistent
view of the metadata associated with an active thin-pool.
- a dm-cache fix for the 4.2 "default" policy switch from "mq" to "smq"
* tag 'dm-4.2-fixes-5' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm cache policy smq: move 'dm-cache-default' module alias to SMQ
dm btree: add ref counting ops for the leaves of top level btrees
dm thin metadata: delete btrees when releasing metadata snapshot
Pull xen block driver fixes from Jens Axboe:
"A few small bug fixes for xen-blk{front,back} that have been sitting
over my vacation"
* 'for-linus' of git://git.kernel.dk/linux-block:
xen-blkback: replace work_pending with work_busy in purge_persistent_gnt()
xen-blkfront: don't add indirect pages to list when !feature_persistent
xen-blkfront: introduce blkfront_gather_backend_features()
- Revert a fix from 4.2-rc5 that was causing lots of WARNING spam.
- Fix a memory leak affecting backends in HVM guests.
- Fix PV domU hang with certain configurations.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVzHsAAAoJEFxbo/MsZsTR9Y0H/2j1PHt29RPcNdgGQ84AH0Wh
tw1emL8rMcdhWQnsO7bNmywNNvRNQnU3ZJ8dzoq+5GPikNsbfQzYc7U2pIL4A+gB
AAJsNDNzecuq4srk8vNxcmZ7ySvm9w6dccDUex2ge3sNWaq6gzSQvz6FSWiL0Sxg
k3JcnemEg6JrYOTWdxKInAORMcRO6rgx9eIsdPUPOpgC5XLg6/mZOqBAWXIksDvs
V9uCMqQicaUgBgKFIOSllqH6fcCNooRu3aDwNNj/2mMcJmEvMeBkHmNlQgEm2j5L
ubdDyrC5y48TUPJm8i3+W2/AY+kgWzhThcqyVy6LRAAj5RItJFxMf0nMXzIEqlQ=
=UgMy
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.2-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen bug fixes from David Vrabel:
- revert a fix from 4.2-rc5 that was causing lots of WARNING spam.
- fix a memory leak affecting backends in HVM guests.
- fix PV domU hang with certain configurations.
* tag 'for-linus-4.2-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/xenbus: Don't leak memory when unmapping the ring on HVM backend
Revert "xen/events/fifo: Handle linked events when closing a port"
x86/xen: build "Xen PV" APIC driver for domU as well
This reverts commits 9a036b93a3 ("x86/signal/64: Remove 'fs' and 'gs'
from sigcontext") and c6f2062935 ("x86/signal/64: Fix SS handling for
signals delivered to 64-bit programs").
They were cleanups, but they break dosemu by changing the signal return
behavior (and removing 'fs' and 'gs' from the sigcontext struct - while
not actually changing any behavior - causes build problems).
Reported-and-tested-by: Stas Sergeev <stsp@list.ru>
Acked-by: Andy Lutomirski <luto@amacapital.net>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking fixes from David Miller:
1) Workaround hw bug when acquiring PCI bos ownership of iwlwifi
devices, from Emmanuel Grumbach.
2) Falling back to vmalloc in conntrack should not emit a warning, from
Pablo Neira Ayuso.
3) Fix NULL deref when rtlwifi driver is used as an AP, from Luis
Felipe Dominguez Vega.
4) Rocker doesn't free netdev on device removal, from Ido Schimmel.
5) UDP multicast early sock demux has route handling races, from Eric
Dumazet.
6) Fix L4 checksum handling in openvswitch, from Glenn Griffin.
7) Fix use-after-free in skb_set_peeked, from Herbert Xu.
8) Don't advertize NETIF_F_FRAGLIST in virtio_net driver, this can lead
to fraglists longer than the driver can support. From Jason Wang.
9) Fix mlx5 on non-4k-pagesize systems, from Carol L Soto.
10) Fix interrupt storm in bna driver, from Ivan Vecera.
11) Don't propagate -EBUSY from netlink_insert(), from Daniel Borkmann.
12) Fix inet request sock leak, from Eric Dumazet.
13) Fix TX interrupt masking and marking in TX descriptors of fs_enet
driver, from LEROY Christophe.
14) Get rid of rule optimizer in gianfar driver, it's buggy and unlikely
to get fixed any time soon. From Jakub Kicinski
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (61 commits)
cosa: missing error code on failure in probe()
gianfar: remove faulty filer optimizer
gianfar: correct list membership accounting
gianfar: correct filer table writing
bonding: Gratuitous ARP gets dropped when first slave added
net: dsa: Do not override PHY interface if already configured
net: fs_enet: mask interrupts for TX partial frames.
net: fs_enet: explicitly remove I flag on TX partial frames
inet: fix possible request socket leak
inet: fix races with reqsk timers
mkiss: Fix error handling in mkiss_open()
bnx2x: Free NVRAM lock at end of each page
bnx2x: Prevent null pointer dereference on SKB release
cxgb4: missing curly braces in t4_setup_debugfs()
net-timestamp: Update skb_complete_tx_timestamp comment
ipv6: don't reject link-local nexthop on other interface
netlink: make sure -EBUSY won't escape from netlink_insert
bna: fix interrupts storm caused by erroneous packets
net: mvpp2: replace TX coalescing interrupts with hrtimer
net: mvpp2: enable proper per-CPU TX buffers unmapping
...
missed during the conversion a couple of years ago.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=AM3b
-----END PGP SIGNATURE-----
Merge tag 'edac_fix_for_4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC fix from Borislav Petkov:
"A ppc4xx_edac fix for accessing ->csrows properly. This driver was
missed during the conversion a couple of years ago"
* tag 'edac_fix_for_4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
EDAC, ppc4xx: Access mci->csrows array elements properly
Currently mdio bindings are defined in keystone.dtsi and this results
in incorrect unit address for the node on K2E and K2L SoCs. Fix this
by moving them to SoC specific DTS file.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Currently the MDIO clock is pointing to clkpa instead of clkcpgmac.
MDIO is part of the ethss and the clock should be clkcpgmac.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=nSeK
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.2/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fix a NULL pointer exception for omap GPMC bus code if probe fails.
* tag 'omap-for-v4.2/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
memory: omap-gpmc: Don't try to save uninitialized GPMC context
Signed-off-by: Olof Johansson <olof@lixom.net>
At the last iteration of the loop, j may equal zero and thus
tp_list[j - 1] causes an invalid read.
Change the logic of the loop so that j - 1 is always >= 0.
Cc: stable@vger.kernel.org
Signed-off-by: Adrien Schildknecht <adrien+dev@schischi.me>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
- Fix i.MX6 PCIe interrupt routing which gets missed from stacked IRQ
domain conversion. The PCIe wakeup support is currently broken
because of this.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVyL2qAAoJEFBXWFqHsHzOGHgH/jgyCg6QVHgxgAoCjySZUbtT
OwYFKxR3697GGVyUMa0r47TQxL5PusCUzJrNJTg6AhhgatKsGfiB45NRZy5bt8k5
8M4tShc1n/fV7N2T1h1QbpXZiPhofhFtMq9Yq1lPDrQvOLOymWWZhGwBqbFy0bJT
4IzqUS7uTE/pvrbFf+iqlwxshSzbbMOOHPqAavyinAKQU5S93v7D4iKJ0q2EmTqh
hypAL1lZ0/BwBKWSeVVzJoVUFHZFmSzhlbE6ZzcY7S/4Dn2oTwiZQPb+eWj8kQHn
CALj6KFSnhQ4XKfcBFTH1Z/apSWs6SDWDOig2jzQ/X+JFo9ahnh4fp91NqLML+o=
=lUqF
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
The i.MX fixes for 4.2, 3rd round:
- Fix i.MX6 PCIe interrupt routing which gets missed from stacked IRQ
domain conversion. The PCIe wakeup support is currently broken
because of this.
* tag 'imx-fixes-4.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx6: correct i.MX6 PCIe interrupt routing
Signed-off-by: Olof Johansson <olof@lixom.net>
1. kfree() of read-only memory (name of power domain returned
by kstrdup_const()),
2. Doubled of_node_put() leading to invalid ref count for OF node.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qAfT
-----END PGP SIGNATURE-----
Merge tag 'samsung-mach-fixes-4.2' of https://github.com/krzk/linux into fixes
Two fixes for bugs in Exynos power domain error exit path:
1. kfree() of read-only memory (name of power domain returned
by kstrdup_const()),
2. Doubled of_node_put() leading to invalid ref count for OF node.
* tag 'samsung-mach-fixes-4.2' of https://github.com/krzk/linux:
ARM: EXYNOS: fix double of_node_put() on error path
ARM: EXYNOS: Fix potentian kfree() of ro memory
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch is based on the upstream commit 5ac1c4bcf0 and amended
for v4.2 to make sure it works as intended.
Repeated calls to begin_crtc_commit can cause warnings like this:
[ 169.127746] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:616
[ 169.127835] in_atomic(): 0, irqs_disabled(): 1, pid: 1947, name: kms_flip
[ 169.127840] 3 locks held by kms_flip/1947:
[ 169.127843] #0: (&dev->mode_config.mutex){+.+.+.}, at: [<ffffffff814774bc>] __drm_modeset_lock_all+0x9c/0x130
[ 169.127860] #1: (crtc_ww_class_acquire){+.+.+.}, at: [<ffffffff814774cd>] __drm_modeset_lock_all+0xad/0x130
[ 169.127870] #2: (crtc_ww_class_mutex){+.+.+.}, at: [<ffffffff81477178>] drm_modeset_lock+0x38/0x110
[ 169.127879] irq event stamp: 665690
[ 169.127882] hardirqs last enabled at (665689): [<ffffffff817ffdb5>] _raw_spin_unlock_irqrestore+0x55/0x70
[ 169.127889] hardirqs last disabled at (665690): [<ffffffffc0197a23>] intel_pipe_update_start+0x113/0x5c0 [i915]
[ 169.127936] softirqs last enabled at (665470): [<ffffffff8108a766>] __do_softirq+0x236/0x650
[ 169.127942] softirqs last disabled at (665465): [<ffffffff8108ae75>] irq_exit+0xc5/0xd0
[ 169.127951] CPU: 1 PID: 1947 Comm: kms_flip Not tainted 4.1.0-rc4-patser+ #4039
[ 169.127954] Hardware name: LENOVO 2349AV8/2349AV8, BIOS G1ETA5WW (2.65 ) 04/15/2014
[ 169.127957] ffff8800c49036f0 ffff8800cde5fa28 ffffffff817f6907 0000000080000001
[ 169.127964] 0000000000000000 ffff8800cde5fa58 ffffffff810aebed 0000000000000046
[ 169.127970] ffffffff81c5d518 0000000000000268 0000000000000000 ffff8800cde5fa88
[ 169.127981] Call Trace:
[ 169.127992] [<ffffffff817f6907>] dump_stack+0x4f/0x7b
[ 169.128001] [<ffffffff810aebed>] ___might_sleep+0x16d/0x270
[ 169.128008] [<ffffffff810aed38>] __might_sleep+0x48/0x90
[ 169.128017] [<ffffffff817fc359>] mutex_lock_nested+0x29/0x410
[ 169.128073] [<ffffffffc01635f0>] ? vgpu_write64+0x220/0x220 [i915]
[ 169.128138] [<ffffffffc017fddf>] ? ironlake_update_primary_plane+0x2ff/0x410 [i915]
[ 169.128198] [<ffffffffc0190e75>] intel_frontbuffer_flush+0x25/0x70 [i915]
[ 169.128253] [<ffffffffc01831ac>] intel_finish_crtc_commit+0x4c/0x180 [i915]
[ 169.128279] [<ffffffffc00784ac>] drm_atomic_helper_commit_planes+0x12c/0x240 [drm_kms_helper]
[ 169.128338] [<ffffffffc0184264>] __intel_set_mode+0x684/0x830 [i915]
[ 169.128378] [<ffffffffc018a84a>] intel_crtc_set_config+0x49a/0x620 [i915]
[ 169.128385] [<ffffffff817fdd39>] ? mutex_unlock+0x9/0x10
[ 169.128391] [<ffffffff81467b69>] drm_mode_set_config_internal+0x69/0x120
[ 169.128398] [<ffffffff8119b547>] ? might_fault+0x57/0xb0
[ 169.128403] [<ffffffff8146bf93>] drm_mode_setcrtc+0x253/0x620
[ 169.128409] [<ffffffff8145c600>] drm_ioctl+0x1a0/0x6a0
[ 169.128415] [<ffffffff810b3b41>] ? get_parent_ip+0x11/0x50
[ 169.128424] [<ffffffff811e9ab8>] do_vfs_ioctl+0x2f8/0x530
[ 169.128429] [<ffffffff810d0fcd>] ? trace_hardirqs_on+0xd/0x10
[ 169.128435] [<ffffffff812e7676>] ? selinux_file_ioctl+0x56/0x100
[ 169.128439] [<ffffffff811e9d71>] SyS_ioctl+0x81/0xa0
[ 169.128445] [<ffffffff81800697>] system_call_fastpath+0x12/0x6f
Solve it by using the newly introduced drm_atomic_helper_commit_planes_on_crtc.
The problem here was that the drm_atomic_helper_commit_planes() helper
we were using was basically designed to do
begin_crtc_commit(crtc #1)
begin_crtc_commit(crtc #2)
...
commit all planes
finish_crtc_commit(crtc #1)
finish_crtc_commit(crtc #2)
The problem here is that since our hardware relies on vblank evasion,
our CRTC 'begin' function waits until we're out of the danger zone in
which register writes might wind up straddling the vblank, then disables
interrupts; our 'finish' function re-enables interrupts after the
registers have been written. The expectation is that the operations between
'begin' and 'end' must be performed without sleeping (since interrupts
are disabled) and should happen as quickly as possible. By clumping all
of the 'begin' calls together, we introducing a couple problems:
* Subsequent 'begin' invocations might sleep (which is illegal)
* The first 'begin' ensured that we were far enough from the vblank that
we could write our registers safely and ensure they all fell within
the same frame. Adding extra delay waiting for subsequent CRTC's
wasn't accounted for and could put us back into the 'danger zone' for
CRTC #1.
This commit solves the problem by using a new helper that allows an
order of operations like:
for each crtc {
begin_crtc_commit(crtc) // sleep (maybe), then disable interrupts
commit planes for this specific CRTC
end_crtc_commit(crtc) // reenable interrupts
}
so that sleeps will only be performed while interrupts are enabled and
we can be sure that registers for a CRTC will be written immediately
once we know we're in the safe zone.
The crtc->config->base.crtc update may seem unrelated, but the helper
will use it to obtain the crtc for the state. Without the update it
will dereference NULL and crash.
Changes since v1:
- Use Matt Roper's commit message.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=90398
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This should be much cleaner, with the same effects.
(cherry picked for v4.2 from commit fb9d6cf8c2)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=90398
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
In
commit d328c9d78d
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Apr 10 16:22:37 2015 +0200
drm/i915: Select starting pipe bpp irrespective or the primary plane
we started to select the pipe bpp from sink capabilities and not from
the primary framebuffer - that one might change (and we don't want to
incur a modeset) and sprites might contain higher bpp content too.
We also selected dithering on a 8 bpc screen displaying a 24bpp rgb
primary, because pipe_bpp is 24 for such a typical 8 bpc sink, but since
the commit mentioned above, base_bpp is always the absolute maximum
supported by the hardware, e.g., 36 bpp on my Ironlake chip. Iow. the
only way to not get dithering would have been to connect a deep color 12
bpc display, so pipe_bpp == 36 == base_bpp.
Hence only enable dithering on 6bpc screens where we difinitely and
always want it.
Cc: Mario Kleiner <mario.kleiner.de@gmail.com>
Reported-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-and-tested-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
When doing pointer operation for accessing the HW S/G table,
a value representing number of entries (and not number of bytes)
must be used.
Cc: <stable@vger.kernel.org> # 3.6+
Fixes: 045e36780f ("crypto: caam - ahash hmac support")
Signed-off-by: Horia Geant? <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Dell laptop causes the white noise by login screen and headphone,
and the fixup function ALC292_FIXUP_DISABLE_AAMIX can eliminate this
noise.
Codec: Realtek ALC3235
Vendor Id: 0x10ec0293
Subsystem Id: 0x102806db
Cc: <stable@vger.kernel.org>
BugLink: https://bugs.launchpad.net/bugs/1484334
Signed-off-by: Woodrow Shen <woodrow.shen@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit
de3910eb79 ("edac: change the mem allocation scheme to
make Documentation/kobject.txt happy")
changed the memory allocation for the csrows member. But ppc4xx_edac was
forgotten in the patch. Fix it.
Signed-off-by: Michael Walle <michael@walle.cc>
Cc: <stable@vger.kernel.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Link: http://lkml.kernel.org/r/1437469253-8611-1-git-send-email-michael@walle.cc
Signed-off-by: Borislav Petkov <bp@suse.de>
If register_hdlc_device() fails, the current code returns 0 but we
should return an error code instead.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski says:
====================
gianfar: filer changes
respinning with examples as requested.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Current filer rule optimization is broken in several ways:
(1) Can perform reads/writes beyond end of allocated tables.
(gianfar_ethtool.c:1326).
(2) It breaks badly for rules with more than 2 specifiers
(e.g. matching ip, port, tos).
Example:
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.1 dst-port 1 tos 1 action 1
Added rule with ID 254
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.2 dst-port 2 tos 2 action 9
Added rule with ID 253
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.3 dst-port 3 tos 3 action 17
Added rule with ID 252
# ./filer_decode /sys/kernel/debug/gfar1/filer_raw
00: MASK == 00000210 AND Q:00 ctrl:00000080 prop:00000210
01: FPR == 00000210 AND CLE Q:00 ctrl:00000281 prop:00000210
02: MASK == ffffffff AND Q:00 ctrl:00000080 prop:ffffffff
03: DPT == 00000003 AND Q:00 ctrl:0000008e prop:00000003
04: TOS == 00000003 AND Q:00 ctrl:0000008a prop:00000003
05: DIA == 0a000003 AND Q:11 ctrl:0000448c prop:0a000003
06: DPT == 00000002 AND Q:00 ctrl:0000008e prop:00000002
07: TOS == 00000002 AND Q:00 ctrl:0000008a prop:00000002
08: DIA == 0a000002 AND Q:09 ctrl:0000248c prop:0a000002
09: DIA == 0a000001 AND Q:00 ctrl:0000008c prop:0a000001
0a: DPT == 00000001 AND Q:00 ctrl:0000008e prop:00000001
0b: TOS == 00000001 CLE Q:01 ctrl:0000060a prop:00000001
ff: MASK >= 00000000 Q:00 ctrl:00000020 prop:00000000
(Entire cluster gets AND-ed together).
(3) We observed that the masking rules it generates do not
play well with clustering on P2020. Only first rule
of the cluster would ever fire. Given that optimizer
relies heavily on masking this is very hard to fix.
Example:
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.1 dst-port 1 action 1
Added rule with ID 254
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.2 dst-port 2 action 9
Added rule with ID 253
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.3 dst-port 3 action 17
Added rule with ID 252
# ./filer_decode /sys/kernel/debug/gfar1/filer_raw
00: MASK == 00000210 AND Q:00 ctrl:00000080 prop:00000210
01: FPR == 00000210 AND CLE Q:00 ctrl:00000281 prop:00000210
02: MASK == ffffffff AND Q:00 ctrl:00000080 prop:ffffffff
03: DPT == 00000003 AND Q:00 ctrl:0000008e prop:00000003
04: DIA == 0a000003 Q:11 ctrl:0000440c prop:0a000003
05: DPT == 00000002 AND Q:00 ctrl:0000008e prop:00000002
06: DIA == 0a000002 Q:09 ctrl:0000240c prop:0a000002
07: DIA == 0a000001 AND Q:00 ctrl:0000008c prop:0a000001
08: DPT == 00000001 CLE Q:01 ctrl:0000060e prop:00000001
ff: MASK >= 00000000 Q:00 ctrl:00000020 prop:00000000
Which looks correct according to the spec but only the first
(eth id 252)/last added rule for 10.0.0.3 will ever trigger.
As if filer did not treat the AND CLE as cluster start but
also kept AND-ing the rules. We found no errata covering this.
The fact that nobody noticed (2) or (3) makes me think
that this feature is not very widely used and we should just
remove it.
Reported-by: Aleksander Dutkowski <adutkowski@gmail.com>
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Acked-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At a cost of one line let's make sure .count is correct
when calling gfar_process_filer_changes().
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAX_FILER_IDX is the last usable index. Using less-than
will already guarantee that one entry for catch-all rule
will be left, no need to subtract 1 here.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the first slave is added (such as during bootup) the first
gratuitous ARP gets dropped. We don't see this drop during a failover.
The packet gets dropped in qdisc (noop_enqueue).
The fix is to delay the sending of gratuitous ARPs till the bond dev's
carrier is present.
It can also be worked around by setting num_grat_arp to more than 1.
Signed-off-by: Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case we need to divert reads/writes using the slave MII bus, we may have
already fetched a valid PHY interface property from Device Tree, and that
mode is used by the PHY driver to make configuration decisions.
If we could not fetch the "phy-mode" property, we will assign p->phy_interface
to PHY_INTERFACE_MODE_NA, such that we can actually check for that condition as
to whether or not we should override the interface value.
Fixes: 19334920ea ("net: dsa: Set valid phy interface type")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit bcdb247c6b ("sd: Limit transfer length") clamped the maximum
size of an I/O request to the MAXIMUM TRANSFER LENGTH field in the BLOCK
LIMITS VPD. This had the unfortunate effect of also limiting the maximum
size of non-filesystem requests sent to the device through sg/bsg.
Avoid using blk_queue_max_hw_sectors() and set the max_sectors queue
limit directly.
Also update the comment in blk_limits_max_hw_sectors() to clarify that
max_hw_sectors defines the limit for the I/O controller only.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reported-by: Brian King <brking@linux.vnet.ibm.com>
Tested-by: Brian King <brking@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org # 3.17+
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Since fc_fcp_cleanup_cmd() can sleep this function must not
be called while holding a spinlock. This patch avoids that
fc_fcp_cleanup_each_cmd() triggers the following bug:
BUG: scheduling while atomic: sg_reset/1512/0x00000202
1 lock held by sg_reset/1512:
#0: (&(&fsp->scsi_pkt_lock)->rlock){+.-...}, at: [<ffffffffc0225cd5>] fc_fcp_cleanup_each_cmd.isra.21+0xa5/0x150 [libfc]
Preemption disabled at:[<ffffffffc0225cd5>] fc_fcp_cleanup_each_cmd.isra.21+0xa5/0x150 [libfc]
Call Trace:
[<ffffffff816c612c>] dump_stack+0x4f/0x7b
[<ffffffff810828bc>] __schedule_bug+0x6c/0xd0
[<ffffffff816c87aa>] __schedule+0x71a/0xa10
[<ffffffff816c8ad2>] schedule+0x32/0x80
[<ffffffffc0217eac>] fc_seq_set_resp+0xac/0x100 [libfc]
[<ffffffffc0218b11>] fc_exch_done+0x41/0x60 [libfc]
[<ffffffffc0225cff>] fc_fcp_cleanup_each_cmd.isra.21+0xcf/0x150 [libfc]
[<ffffffffc0225f43>] fc_eh_device_reset+0x1c3/0x270 [libfc]
[<ffffffff814a2cc9>] scsi_try_bus_device_reset+0x29/0x60
[<ffffffff814a3908>] scsi_ioctl_reset+0x258/0x2d0
[<ffffffff814a2650>] scsi_ioctl+0x150/0x440
[<ffffffff814b3a9d>] sd_ioctl+0xad/0x120
[<ffffffff8132f266>] blkdev_ioctl+0x1b6/0x810
[<ffffffff811da608>] block_ioctl+0x38/0x40
[<ffffffff811b4e08>] do_vfs_ioctl+0x2f8/0x530
[<ffffffff811b50c1>] SyS_ioctl+0x81/0xa0
[<ffffffff816cf8b2>] system_call_fastpath+0x16/0x7a
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Due to patch "libfc: Do not invoke the response handler after
fc_exch_done()" (commit ID 7030fd62) the lport_recv() call
in fc_exch_recv_req() is passed a dangling pointer. Avoid this
by moving the fc_frame_free() call from fc_invoke_resp() to its
callers. This patch fixes the following crash:
general protection fault: 0000 [#3] PREEMPT SMP
RIP: fc_lport_recv_req+0x72/0x280 [libfc]
Call Trace:
fc_exch_recv+0x642/0xde0 [libfc]
fcoe_percpu_receive_thread+0x46a/0x5ed [fcoe]
kthread+0x10a/0x120
ret_from_fork+0x42/0x70
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Pull amd drm fixes from Alex Deucher:
"Dave is on vacation at the moment, so please pull these radeon and
amdgpu fixes directly.
Just a few minor things for 4.2:
- add a new radeon pci id
- fix a power management regression in amdgpu
- fix HEVC command buffer validation in amdgpu"
* 'drm-fixes-4.2' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: add new OLAND pci id
Revert "drm/amdgpu: Configure doorbell to maximum slots"
drm/amdgpu: add context buffer size check for HEVC
In case of hw iscsi offload, an host can have N-number of active
connections. There can be IO's running on some connections which
make host->host_busy always TRUE. Now if logout from a connection
is tried then the code gets into an infinite loop as host->host_busy
is always TRUE.
iscsi_conn_teardown(....)
{
.........
/*
* Block until all in-progress commands for this connection
* time out or fail.
*/
for (;;) {
spin_lock_irqsave(session->host->host_lock, flags);
if (!atomic_read(&session->host->host_busy)) { /* OK for ERL == 0 */
spin_unlock_irqrestore(session->host->host_lock, flags);
break;
}
spin_unlock_irqrestore(session->host->host_lock, flags);
msleep_interruptible(500);
iscsi_conn_printk(KERN_INFO, conn, "iscsi conn_destroy(): "
"host_busy %d host_failed %d\n",
atomic_read(&session->host->host_busy),
session->host->host_failed);
................
...............
}
}
This is not an issue with software-iscsi/iser as each cxn is a separate
host.
Fix:
Acquiring eh_mutex in iscsi_conn_teardown() before setting
session->state = ISCSI_STATE_TERMINATE.
Signed-off-by: John Soni Jose <sony.john@avagotech.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Chris Leech <cleech@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Odin.com>
When expanding a cache block we use krealloc() to resize the register
present bitmap without initialising the newly allocated data (the
original code was written for kzalloc()). Add an appropraite memset()
to fix that.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVyztsAAoJECTWi3JdVIfQ8QIH/RGXFhPUPWdXhi4JYn8+bIGb
6SSBzsxGlCocWBrzyaZRcz/WB7Na7t+oXoYEjk8CA+/8zPLRoCXHKmIETmQW0+7G
hUY+YNk8xxUtPuReeGgqZ7z9l9mC2f0UVPvgWn6dELamxtqr0LmODdKp5D3vLQLp
c2eFqZr3wjYwC9vuWElaUftyQzSYaj6Rr6PnZ6bD/pN/YY3zd53gt7QluT9SzUxs
5uZXhd1UD6GTDxCrtfqemlEaOYpQOdMO0h/3Eko4MbdCeq3bOq6kn9a+E7nfvE4v
dIeEdafqVABgKHi66B83Fu/5eJI+kI+qo9u2QuWLB9AWAJnZuiZc968eIDaKMBE=
=GTVe
-----END PGP SIGNATURE-----
Merge tag 'regmap-fix-v4.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fix from Mark Brown:
"regmap: Fix handling of present bits on rbtree cache block resize
When expanding a cache block we use krealloc() to resize the register
present bitmap without initialising the newly allocated data (the
original code was written for kzalloc()). Add an appropraite memset()
to fix that"
* tag 'regmap-fix-v4.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: regcache-rbtree: Clean new present bits on present bitmap resize
When creating dm-cache with the default policy, it will call
request_module("dm-cache-default") to register the default policy.
But the "dm-cache-default" alias was left referring to the MQ policy.
Fix this by moving the module alias to SMQ.
Fixes: bccab6a0 (dm cache: switch the "default" cache replacement policy from mq to smq)
Signed-off-by: Yi Zhang <yizhan@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
When using nested btrees, the top leaves of the top levels contain
block addresses for the root of the next tree down. If we shadow a
shared leaf node the leaf values (sub tree roots) should be incremented
accordingly.
This is only an issue if there is metadata sharing in the top levels.
Which only occurs if metadata snapshots are being used (as is possible
with dm-thinp). And could result in a block from the thinp metadata
snap being reused early, thus corrupting the thinp metadata snap.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
The device details and mapping trees were just being decremented
before. Now btree_del() is called to do a deep delete.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
We fail to free the shared_regs allocation if the constraint_list
allocation fails.
Cure this and be more consistent in NULL-ing the pointers after free.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
I ran the perf fuzzer, which triggered some WARN()s which are due to
trying to stop/restart an event on the wrong CPU.
Use the normal IPI pattern to ensure we run the code on the correct CPU.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: bad7192b84 ("perf: Fix PERF_EVENT_IOC_PERIOD to force-reset the period")
Signed-off-by: Ingo Molnar <mingo@kernel.org>
If rb->aux_refcount is decremented to zero before rb->refcount,
__rb_free_aux() may be called twice resulting in a double free of
rb->aux_pages. Fix this by adding a check to __rb_free_aux().
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Fixes: 57ffc5ca67 ("perf: Fix AUX buffer refcounting")
Link: http://lkml.kernel.org/r/1437953468.12842.17.camel@decadent.org.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
