Until now clk81 was used as gate clock for the ethernet controller on
Meson8 whereas Meson8b did not configure a gate clock at all. Use
CLKID_ETH for both SoCs, which is the real gate clock for the ethernet
controller.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Amlogic's Meson8b SoC has a Snoop Control Unit (SCU), just like many
other Cortex-A5 SoCs. Add the corresponding devicetree node so it can be
used during SMP boot.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This adds the DWC2 USB controller nodes and the corresponding USB2 PHY
nodes to meson.dtsi (as the same - or at least a very similar) IP block
is used on all SoCs (at the same physical address).
Additionally meson8.dtsi and meson8b.dtsi add the required clocks to the
DWC2 and USB2 PHY nodes, otherwise the DWC2 controller cannot be
initialized by the dwc2 driver.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
All supported Meson SoCs have a random number generator in CBUS.
Newer SoCs (GXBB, GXL and GXM) provide only one 32-bit random number
register, whereas the older SoCs (Meson6, Meson8 and Meson8b) have two
32-bit random number registers. The existing meson-rng driver only
supports the lower 32-bit - but it still works fine on the older SoCs
apart from this small limitation.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This adds the SAR ADC to meson.dtsi and configures the clocks on Meson8
and Meson8b to allow boards to use it. Some boards use it to connect a
button to it.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch extends the L2 cache controller node for the Amlogic Meson8
and Meson8b SoCs with some missing parameters. These are taken from the
Amlogic GPL kernel source.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
[apply the change to Meson8 and Meson8b and updated description]
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Currently only meson6.dtsi and meson8.dtsi inherit the generic
meson.dtsi. However, since the Meson8b platform is basically a slightly
updated version of Meson8 we can safely inherit meson.dtsi. An indicator
for this are the nodes which are identical in meson.dtsi and
meson8b.dtsi (L2, gic, timer, uart_AO, uart_A, uart_B, uart_C).
Additionally this makes the following devices available on Meson8b which
were not avaialble before (however, since all affected drivers support
Meson6, Meson8 and the whole GX series there's no reason to assume that
they are not working):
- i2c_a and i2c_B
- the IR receiver
- SPFIC (SPI flash controller)
- the dwmac ethernet controller
Differences between Meson8 and Meson8b seem to be:
- ARM Cortex-A5 core instead of Cortex-A9 on Meson8
- dwmac on Meson8b supports RGMII
- small pinctrl updates
Inheriting meson.dtsi makes it easier to maintain by removing duplicate
definitions.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Update DTSI file to add the reset controller node.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
