The bq32000 includes a trickle charge circuit to maintain the charge of the
backup supply when a super capacitor is used.
You can enable the charging circuit by setting 'trickle-resistor-ohms',
additionally you can set TCFE to 1 to bypass the internal diode and boost
the charge voltage of the backup supply. You might want to enable/disable
the TCFE switch from userspace (e.g when device is only connected to a
battery)
This patch introduces a new sysfs entry to enable and disable this FET
form userspace.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Now that we have a devm variant of rtc_device_register, switch to it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The RTC controls the input source of the main 32kHz oscillator in the
system, feeding it to the clock unit too.
By default, this is using an internal, very inaccurate (+/- 30%)
oscillator with a divider to make it roughly around 32kHz. This is however
quite impractical for the RTC, since our time will not be tracked properly.
Since this oscillator is an input of the main clock unit, and since that
clock unit will be probed using CLK_OF_DECLARE, we have to use it as well,
leading to a two stage probe: one to enable the clock, the other one to
enable the RTC.
There is also a slight change in the binding that is required (and should
have been from the beginning), since we'll need a phandle to the external
oscillator used on that board. We support the old binding by not allowing
to switch to the external oscillator and only using the internal one (which
was the previous behaviour) in the case where we're missing that phandle.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The RTC is clocked from either an internal, imprecise, oscillator or an
external one, which is usually much more accurate.
The difference perceived between the time elapsed and the time reported by
the RTC is in a 10% scale, which prevents the RTC from being useful at all.
Fortunately, the external oscillator is reported to be mandatory in the
Allwinner datasheet, so we can just switch to it.
Cc: stable@vger.kernel.org
Fixes: 9765d2d943 ("rtc: sun6i: Add sun6i RTC driver")
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Some registers have a read-modify-write access pattern that are not atomic.
Add some locking to prevent from concurrent accesses.
Cc: stable@vger.kernel.org
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
By using kernel_halt() instead of machine_halt(), we can make the driver
build as a module.
However, jz4740 platforms not loading this module will not be able to power
off.
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Revert "rtc: jz4740: make the driver builtin only"
This reverts commit b9168c539c.
The current pinconf packed format allows only 16-bit argument limiting
the maximum value 65535. For most types this is enough. However,
debounce time can be in range of hundreths of milliseconds in case of
mechanical switches so we cannot represent the worst case using the
current format.
In order to support larger values change the packed format so that the
lower 8 bits are used as type which leaves 24 bits for the argument.
This allows representing values up to 16777215 and debounce times up to
16 seconds.
We also convert the existing users to use 32-bit integer when extracting
argument from the packed configuration value.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since we have to provide the clock very early on, the RTC driver cannot be
built as a module. Make sure that won't happen.
Cc: stable@vger.kernel.org
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This patches fixes comparison between signed and unsigned values as it
could produce an incorrect result when the signed value is converted to
unsigned:
drivers/rtc/rtc-stm32.c: In function 'stm32_rtc_valid_alrm':
drivers/rtc/rtc-stm32.c:404:21: warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
if ((((tm->tm_year > cur_year) &&
...
It also fixes comparison always true or false due to the fact that unsigned
value is compared against zero with >= or <:
drivers/rtc/rtc-stm32.c: In function 'stm32_rtc_init':
drivers/rtc/rtc-stm32.c:514:35: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
for (pred_a = pred_a_max; pred_a >= 0; pred_a-- ) {
drivers/rtc/rtc-stm32.c:530:44: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
(rate - ((pred_a + 1) * (pred_s + 1)) < 0) ?
Fixes: 4e64350f42 ("rtc: add STM32 RTC driver")
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Using the ~ operator on a BIT() constant results in a large 'unsigned long'
constant that won't fit into an 'unsigned int' function argument on 64-bit
architectures, resulting in a harmless build warning in x86 allmodconfig:
drivers/rtc/rtc-stm32.c: In function 'stm32_rtc_probe':
drivers/rtc/rtc-stm32.c:651:51: error: large integer implicitly truncated to unsigned type [-Werror=overflow]
regmap_update_bits(rtc->dbp, PWR_CR, PWR_CR_DBP, ~PWR_CR_DBP);
As PWR_CR_DBP mask prevents other bits to be cleared, replace all
~PWR_CR_DBP by 0.
Fixes: 4e64350f42 ("rtc: add STM32 RTC driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Accessing the registers of the RTC block on Tegra requires the module
clock to be enabled. This only works because the RTC module clock will
be enabled by default during early boot. However, because the clock is
unused, the CCF will disable it at late_init time. This causes the RTC
to become unusable afterwards. This can easily be reproduced by trying
to use the RTC:
$ hwclock --rtc /dev/rtc1
This will hang the system. I ran into this by following up on a report
by Martin Michlmayr that reboot wasn't working on Tegra210 systems. It
turns out that the rtc-tegra driver's ->shutdown() implementation will
hang the CPU, because of the disabled clock, before the system can be
rebooted.
What confused me for a while is that the same driver is used on prior
Tegra generations where the hang can not be observed. However, as Peter
De Schrijver pointed out, this is because on 32-bit Tegra chips the RTC
clock is enabled by the tegra20_timer.c clocksource driver, which uses
the RTC to provide a persistent clock. This code is never enabled on
64-bit Tegra because the persistent clock infrastructure does not exist
on 64-bit ARM.
The proper fix for this is to add proper clock handling to the RTC
driver in order to ensure that the clock is enabled when the driver
requires it. All device trees contain the clock already, therefore
no additional changes are required.
Reported-by: Martin Michlmayr <tbm@cyrius.com>
Acked-By Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The ordering of includes is currently completely arbitrary, making it
impossible to decide where to put new includes. Remove the dilemma by
sort the include list alphabetically.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The new driver has a stray #ifdef in it that causes a build error:
drivers/rtc/rtc-stm32.c:718:21: error: 'stm32_rtc_of_match' undeclared here (not in a function); did you mean 'stm32_rtc_pm_ops'?
As the #ifdef serves no purpose here, let's just remove it.
Fixes: 4e64350f42 ("rtc: add STM32 RTC driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The remove function can be called at runtime for a manual 'unbind'
operation and must not be left out from a built-in driver, as kbuild
complains:
`stm32_rtc_remove' referenced in section `.data.stm32_rtc_driver' of drivers/rtc/rtc-stm32.o: defined in discarded section `.exit.text' of drivers/rtc/rtc-stm32.o
This removes the extraneous annotation.
Fixes: 4e64350f42 ("rtc: add STM32 RTC driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This patch adds support for the STM32 RTC.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Armada38x wants to modify its rtc_class_ops to remove the interrupt
handling when there is no usable interrupt, but this means we leave
function pointers in writable memory.
Since rtc_class_ops is small, arrange to have two instances, one for
when we have interrupts, and one for when we have none, both marked
const. This allows the compiler to place them in read-only memory,
which is better than placing them in __ro_after_init.
Thanks to Bhumika Goyal <bhumirks@gmail.com> for pointing out that
the structure was writable and submitting a patch to add
__ro_after_init.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Declare rtc_class_ops structures as const as they are only passed
as an argument to the function devm_rtc_device_register. This argument
is of type const struct rtc_class_ops *, so rtc_class_ops structures
having this property can be declared const.
Done using Coccinelle:
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct rtc_class_ops i@p = {...};
@ok1@
identifier r1.i;
position p;
@@
devm_rtc_device_register(...,&i@p,...)
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct rtc_class_ops i;
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The DryIce chipset has a dedicated security violation interrupt that is
triggered for security violations (if configured to do so). According
to the publicly available imx258 reference manual, irq 56 is used for
this interrupt.
If an irq number is provided for the security violation interrupt,
install the same handler that we're already using for the "normal"
interrupt.
imxdi->irq is used only in the probe function, make it a local variable.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This patch adds alarm support. This allows to configure the chip
to generate an interrupt when the alarm matches current time value.
Alarm can be programmed up to one year in the future
and is accurate to the second.
Signed-off-by: Emil Bartczak <emilbart@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This patch adds support for saving/loading weekday value from the chip.
Signed-off-by: Emil Bartczak <emilbart@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
According to RES-3124064:
The device supports CPU write and read access to the RTC time register.
However, due to this restriction, read and write from/to internal RTC
register may fail.
Workaround:
General setup:
1. Configure the RTC Mbus Bridge Timing Control register (offset 0x184A0)
to value 0xFD4D4FFF
Write RTC WRCLK Period to its maximum value (0x3FF)
Write RTC WRCLK setup to 0x29
Write RTC WRCLK High Time to 0x53 (default value)
Write RTC Read Output Delay to its maximum value (0x1F)
Mbus - Read All Byte Enable to 0x1 (default value)
2. Configure the RTC Test Configuration Register (offset 0xA381C) bit3
to '1' (Reserved, Marvell internal)
For any RTC register read operation:
1. Read the requested register 100 times.
2. Find the result that appears most frequently and use this result
as the correct value.
For any RTC register write operation:
1. Issue two dummy writes of 0x0 to the RTC Status register (offset
0xA3800).
2. Write the time to the RTC Time register (offset 0xA380C).
This patch is based on the work of Shaker Daibes
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Fixes checkpatch.pl warning:
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
Signed-off-by: Vesa Jääskeläinen <vesa.jaaskelainen@vaisala.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Texas Instrument's TPS65910 has support for compensating RTC crystal
inaccuracies. When enabled every hour RTC counter value will be compensated
with two's complement value.
Signed-off-by: Vesa Jääskeläinen <vesa.jaaskelainen@vaisala.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
ktime_set(S,N) was required for the timespec storage type and is still
useful for situations where a Seconds and Nanoseconds part of a time value
needs to be converted. For anything where the Seconds argument is 0, this
is pointless and can be replaced with a simple assignment.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
ktime is a union because the initial implementation stored the time in
scalar nanoseconds on 64 bit machine and in a endianess optimized timespec
variant for 32bit machines. The Y2038 cleanup removed the timespec variant
and switched everything to scalar nanoseconds. The union remained, but
become completely pointless.
Get rid of the union and just keep ktime_t as simple typedef of type s64.
The conversion was done with coccinelle and some manual mopping up.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Subsystem:
- non-modular drivers are now explicitly non-modular
New driver:
- Epson Toyocom rtc-7301sf/dg
Drivers:
- cmos: reject unsupported alarm values wrt the RTC capabilities
- ds1307: ACPI support
- jz4740: DT support, jz4780 handling, can now be used as a system power
controller
- mcp795: many fixes, in particular proper month handling
- twl: driver is now DT only
-----BEGIN PGP SIGNATURE-----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=z4SX
-----END PGP SIGNATURE-----
Merge tag 'rtc-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Subsystem:
- non-modular drivers are now explicitly non-modular
New driver:
- Epson Toyocom rtc-7301sf/dg
Drivers:
- cmos: reject unsupported alarm values wrt the RTC capabilities
- ds1307: ACPI support
- jz4740: DT support, jz4780 handling, can now be used as a system
power controller
- mcp795: many fixes, in particular proper month handling
- twl: driver is now DT only"
* tag 'rtc-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (31 commits)
rtc: mcp795: Fix whitespace and indentation.
rtc: mcp795: Prefer using the BIT() macro.
rtc: mcp795: fix month write resetting date to 1.
rtc: mcp795: fix time range difference between linux and RTC chip.
rtc: mcp795: fix bitmask value for leap year (LP).
rtc: mcp795: use bcd2bin/bin2bcd.
rtc: add support for EPSON TOYOCOM RTC-7301SF/DG
rtc: ds1307: Add ACPI support
rtc: imxdi: (trivial) fix a typo
rtc: ds1374: Merge conditional + WARN_ON()
rtc: twl: make driver DT only
rtc: twl: kill static variables
rtc: fix typos in Kconfig
rtc: jz4740: make the driver builtin only
rtc: jz4740: remove unused EXPORT_SYMBOL
Documentation: bindings: fix twl-rtc documentation
rtc: Enable compile testing for Maxim and Samsung drivers
MIPS: jz4740: Remove obsolete code
MIPS: qi_lb60: Probe RTC driver from DT and use it as power controller
MIPS: jz4740: DTS: Probe the jz4740-rtc driver from devicetree
...
Fix whitespace and indentation errors and the following
checkpatch warnings:
- line 15: Block comments use a trailing */ on a separate line
- line 256: Line over 80 characters
No code change.
Signed-off-by: Emil Bartczak <emilbart@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This patch doesn't change the code but replaces all bitmask values
with the BIT(x) macro.
Signed-off-by: Emil Bartczak <emilbart@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
According to Microchip errata some combinations of date and month
values may result in the date being reset to 1, even if the date
is also written with the month (for example 31-07 or 31-08).
As a workaround avoid writing date and month values within the same
Write command. Instead, terminate the Write command after loading
the date and begin a new command to write the month. In addition,
disable the oscillator before loading the new values. This is done
by ensuring both the ST and EXTOSC bits are cleared and waiting for
the OSCON bit to clear.
Signed-off-by: Emil Bartczak <emilbart@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
In linux rtc_time struct, tm_mon range is 0~11, while in RTC HW REG,
month range is 1~12. This patch adjusts difference of them.
Signed-off-by: Emil Bartczak <emilbart@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
According the datasheet the leap year is a fifth bit in month register.
Signed-off-by: Emil Bartczak <emilbart@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Change rtc-mcp795.c to use the bcd2bin/bin2bcd functions.
This change fixes the wrong conversion of month value
from binary to BCD (missing right shift operation for 10 month).
Signed-off-by: Emil Bartczak <emilbart@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This adds support for EPSON TOYOCOM RTC-7301SF/DG which has parallel
interface compatible with SRAM.
This driver supports basic clock, calendar and alarm functionality.
Tested with Microblaze linux running on Artix7 FPGA board with my own
custom IP for RTC-7301.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This patch enables ACPI support for rtc-ds1307 driver.
Signed-off-by: Tin Huynh <tnhuynh@apm.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Pull timer updates from Thomas Gleixner:
"The time/timekeeping/timer folks deliver with this update:
- Fix a reintroduced signed/unsigned issue and cleanup the whole
signed/unsigned mess in the timekeeping core so this wont happen
accidentaly again.
- Add a new trace clock based on boot time
- Prevent injection of random sleep times when PM tracing abuses the
RTC for storage
- Make posix timers configurable for real tiny systems
- Add tracepoints for the alarm timer subsystem so timer based
suspend wakeups can be instrumented
- The usual pile of fixes and updates to core and drivers"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
timekeeping: Use mul_u64_u32_shr() instead of open coding it
timekeeping: Get rid of pointless typecasts
timekeeping: Make the conversion call chain consistently unsigned
timekeeping_Force_unsigned_clocksource_to_nanoseconds_conversion
alarmtimer: Add tracepoints for alarm timers
trace: Update documentation for mono, mono_raw and boot clock
trace: Add an option for boot clock as trace clock
timekeeping: Add a fast and NMI safe boot clock
timekeeping/clocksource_cyc2ns: Document intended range limitation
timekeeping: Ignore the bogus sleep time if pm_trace is enabled
selftests/timers: Fix spelling mistake "Asyncrhonous" -> "Asynchronous"
clocksource/drivers/bcm2835_timer: Unmap region obtained by of_iomap
clocksource/drivers/arm_arch_timer: Map frame with of_io_request_and_map()
arm64: dts: rockchip: Arch counter doesn't tick in system suspend
clocksource/drivers/arm_arch_timer: Don't assume clock runs in suspend
posix-timers: Make them configurable
posix_cpu_timers: Move the add_device_randomness() call to a proper place
timer: Move sys_alarm from timer.c to itimer.c
ptp_clock: Allow for it to be optional
Kconfig: Regenerate *.c_shipped files after previous changes
...
WARN_ON does both these things in one statement.
Using a better pattern with WARN_ON().
Signed-off-by: Srikant Ritolia <s.ritolia@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Since there are no platform based users and all users
of this code are TI OMAP-based which is DT only, it makes
sense to remove unused code.
Signed-off-by: Nicolae Rosia <Nicolae_Rosia@mentor.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The current code uses static variables which prevent
the use of multiple rtc twl instances.
We also make it clear that this driver supports only
TWL4030 and TWL6030 classes.
Signed-off-by: Nicolae Rosia <Nicolae_Rosia@mentor.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Power management suspend/resume tracing (ab)uses the RTC to store
suspend/resume information persistently. As a consequence the RTC value is
clobbered when timekeeping is resumed and tries to inject the sleep time.
Commit a4f8f6667f ("timekeeping: Cap array access in timekeeping_debug")
plugged a out of bounds array access in the timekeeping debug code which
was caused by the clobbered RTC value, but we still use the clobbered RTC
value for sleep time injection into kernel timekeeping, which will result
in random adjustments depending on the stored "hash" value.
To prevent this keep track of the RTC clobbering and ignore the invalid RTC
timestamp at resume. If the system resumed successfully clear the flag,
which marks the RTC as unusable, warn the user about the RTC clobber and
recommend to adjust the RTC with 'ntpdate' or 'rdate'.
[jstultz: Fixed up pr_warn formating, and implemented suggestions from Ingo]
[ tglx: Rewrote changelog ]
Originally-from: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Xunlei Pang <xlpang@redhat.com>
Cc: Len Brown <lenb@kernel.org>
Link: http://lkml.kernel.org/r/1480372524-15181-3-git-send-email-john.stultz@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Since the driver is now calling machine_halt() that is not exported, it has
to be built in the kernel. Building it as a module will fail at linking
time.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
max8907, max77686 and s5m RTC drivers can be compile tested to increase
build coverage. The s5m-rtc uses REGMAP_IRQ so add this as explicit
dependency.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The 'system-power-controller' singleton entry can be used in the
devicetree node of the jz4740-rtc driver to specify that the driver is
granted the right to power off the system through the registers of the
RTC unit.
See the documentation for more details:
Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
See
Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt
for a description of the bindings.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The RTC unit present in the JZ4780 works mostly the same as the one in
the JZ4740. The major difference is that register writes need to be
explicitly enabled, by writing a magic code (0xA55A) to a "write
enable" register before each access.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The Kconfig currently controlling compilation of this code is:
drivers/rtc/Kconfig:config RTC_DRV_SUN4V
drivers/rtc/Kconfig: bool "SUN4V Hypervisor RTC"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
We delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Cc: rtc-linux@googlegroups.com
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The Kconfig currently controlling compilation of this code is:
drivers/rtc/Kconfig:config RTC_DRV_STARFIRE
drivers/rtc/Kconfig: bool "Starfire RTC"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
We delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Cc: rtc-linux@googlegroups.com
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The Kconfig currently controlling compilation of this code is:
drivers/rtc/Kconfig:config RTC_LIB
drivers/rtc/Kconfig: bool
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
We delete the MODULE_LICENSE tag since all that information
is already contained at the top of the file in the comments.
We don't replace module.h with init.h since the file doesn't need that.
However we do add export.h since the file uses EXPORT_SYMBOL.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: rtc-linux@googlegroups.com
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
If RTC is running from an internal clock source, the RTC module can't
be disabled; otherwise it stops ticking completely. Current suspend
handler implementation disables the clock/module unconditionally,
instead fix this by disabling the clock only if we are running on
external clock source, which is not affected by suspend.
The prevention of disabling the clock must be done via implementing
the runtime_pm handlers for the device, and returning an error code
from the runtime suspend handler; otherwise OMAP core PM will disable
the clocks for the driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
RTC can be clocked from an external 32KHz oscillator, or from the
Peripheral PLL. The RTC has an internal oscillator buffer to support
direct operation with a crystal.
----------------------------------------
| Device --------- |
| | | |
| | RTCSS | |
| --------- | | |
OSC |<------| RTC | | | |
|------>| OSC |--- | | |
| -------- | | | |
| ----|clk | |
| -------- | | | |
| | PRCM |--- | | |
| -------- -------- |
----------------------------------------
The RTC functional clock is sourced by default from the clock derived
from the Peripheral PLL. In order to select source as external osc clk
the following changes needs to be done:
- Enable the RTC OSC (RTC_OSC_REG[4]OSC32K_GZ = 0)
- Enable the clock mux(RTC_OSC_REG[6]K32CLK_EN = 1)
- Select the external clock source (RTC_OSC_REG[3]32KCLK_SEL = 1)
Fixes: 399cf0f63f ("rtc: omap: Add external clock enabling support")
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add a sanity check to see if chip is present. If we can not communicate
with the chip there is no point in registering a RTC device.
Signed-off-by: Mirza Krak <mirza.krak@hostmobility.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
That header has been gone for a while. I've fixed up the Kconfig
comment, but the one in rtc-cmos.c doesn't make any sense to me
even looking at its history.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Some platforms allows to specify the month and day of the month in
which an alarm should go off, some others the day of the month and
some others just the time.
Currently any given value is accepted by the driver and only the
supported fields are used to program the hardware. As consequence,
alarms are potentially programmed to go off in the wrong moment.
Fix this by rejecting any unsupported value.
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
If the driver is built as a module, autoload won't work because the module
alias information is not filled so user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/rtc/rtc-asm9260.ko | grep alias
$
After this patch:
$ modinfo drivers/rtc/rtc-asm9260.ko | grep alias
alias: of:N*T*Calphascale,asm9260-rtcC*
alias: of:N*T*Calphascale,asm9260-rtc
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Subsystem:
- delete owner assignment in multiple drivers
- constify rtc_class_ops structures
Drivers:
- ac100: support clock-output-names
- cmos: properly handle ACPI alarms and quirky BIOSes and other fixes
- ds1307: fix century bit support while staying comaptible with previous
behaviour by default
- ds1347: switch to regmap
- isl12057 is now handled by ds1307
- omap: support external wakeup
- rv8803: allow to disable voltage drop detection
-----BEGIN PGP SIGNATURE-----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=ZqqR
-----END PGP SIGNATURE-----
Merge tag 'rtc-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"RTC for 4.9
Subsystem:
- delete owner assignment in multiple drivers
- constify rtc_class_ops structures
Drivers:
- ac100: support clock-output-names
- cmos: properly handle ACPI alarms and quirky BIOSes and other fixes
- ds1307: fix century bit support while staying comaptible with
previous behaviour by default
- ds1347: switch to regmap
- isl12057 is now handled by ds1307
- omap: support external wakeup
- rv8803: allow to disable voltage drop detection"
* tag 'rtc-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (25 commits)
rtc: rv8803: set VDETOFF and SWOFF via device tree
dt/bindings: Add bindings for Micro Crystal rv8803
devicetree: Add Micro Crystal AG vendor id
rtc: cmos: avoid unused function warning
rtc: ac100: Add NULL checking for devm_kzalloc call
rtc: ds1347: changed raw spi calls to register map calls
rtc: cmos: Restore alarm after resume
rtc: cmos: Clear ACPI-driven alarms upon resume
rtc: omap: Support ext_wakeup configuration
rtc: cmos: Initialize hpet timer before irq is registered
rtc: asm9260: rework locking
rtc: asm9260: allow COMPILE_TEST
rtc: constify rtc_class_ops structures
rtc: ac100: support clock-output-names in device tree binding
rtc: rx6110: remove owner assignment
rtc: pic32: Delete owner assignment
rtc: bq32k: Fix handling of oscillator failure flag
rtc: bq32k: Use correct mask name for 'minutes' register.
rtc: sysfs: fix a cast removing the const attribute
Documentation: dt: Intersil isl12057 is not a trivial device
...
There might be designs where the power supply circuit is designed
in a way that VDETOFF and SWOFF is required to be set. Otherwise the
RTC detects a power loss. Add a device tree interface for this.
Signed-off-by: Carsten Resch <Carsten.Resch@de.bosch.com>
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Oleksij Rempel <fixed-term.Oleksij.Rempel@de.bosch.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
A bug fix for the ACPI side of this driver caused a harmless
build warning:
drivers/rtc/rtc-cmos.c:1115:13: error: 'cmos_check_acpi_rtc_status' defined but not used [-Werror=unused-function]
static void cmos_check_acpi_rtc_status(struct device *dev,
We can avoid the warning and simplify the driver at the same time
by removing the #ifdef for CONFIG_PM and rely on the SIMPLE_DEV_PM_OPS()
to set everything up correctly. cmos_resume() has to get marked
as __maybe_unused so we don't introduce another warning, and
the two variants of cmos_poweroff() can get merged into one using
an IS_ENABLED() check.
Fixes: 983bf1256e ("rtc: cmos: Clear ACPI-driven alarms upon resume")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
devm_kzalloc can return NULL, add NULL checking to prevent NULL pointer
dereference.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Some platform firmware may interfere with the RTC alarm over suspend,
resulting in the kernel and hardware having different ideas about system
state but also potentially causing problems with firmware that assumes the
OS will clean this case up. This patch restores the RTC alarm on resume
to ensure that kernel and hardware are in sync.
The case we've seen is Intel Rapid Start, which is a firmware-mediated
feature that automatically transitions systems from suspend-to-RAM to
suspend-to-disk without OS involvement. It does this by setting the RTC
alarm and a flag that indicates that on wake it should perform the
transition rather than re-starting the OS. However, if the OS has set a
wakeup alarm that would wake the machine earlier, it refuses to overwrite
it and allows the system to wake instead.
This fails in the following situation:
1) User configures Intel Rapid Start to transition after (say) 15
minutes
2) User suspends to RAM. Firmware sets the wakeup alarm for 15 minutes
in the future
3) User resumes after 5 minutes. Firmware does not reset the alarm, and
as such it is still set for 10 minutes in the future
4) User suspends after 5 minutes. Firmware notices that the alarm is set
for 5 minutes in the future, which is less than the 15 minute transition
threshold. It therefore assumes that the user wants the machine to wake
in 5 minutes
5) System resumes after 5 minutes
The worst case scenario here is that the user may have put the system in a
bag between (4) and (5), resulting in it running in a confined space and
potentially overheating. This seems reasonably important. The Rapid
Start support code got added in 3.11, but it can be configured in the
firmware regardless of kernel support.
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Currently ACPI-driven alarms are not cleared when they wake the
system. As consequence, expired alarms must be manually cleared to
program a new alarm. Fix this by correctly handling ACPI-driven
alarms.
More specifically, the ACPI specification [1] provides for two
alternative implementations of the RTC. Depending on the
implementation, the driver either clear the alarm from the resume
callback or from ACPI interrupt handler:
- The platform has the RTC wakeup status fixed in hardware
(ACPI_FADT_FIXED_RTC is 0). In this case the driver can determine
if the RTC was the reason of the wakeup from the resume callback
by reading the RTC status register.
- The platform has no fixed hardware feature event bits. In this
case a GPE is used to wake the system and the driver clears the
alarm from its handler.
[1] http://www.acpi.info/DOWNLOADS/ACPI_5_Errata%20A.pdf
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Support configuration of ext_wakeup sources. This patch makes it
possible to enable ext_wakeup and set it's polarity, depending on board
configuration. AM335x's dedicated PMIC (tps65217) uses ext_wakeup to
notify about power-button presses. Handling power-button presses enables
to recover from RTC-only power states correctly.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The rtc-asm9260 driver uses a discrete spinlock (wrongly uninitialized).
Use the rtc mutex to lock mmio accesses instead.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The rtc-asm9260 driver compiles correctly on other architectures, add
COMPILE_TEST to improve code coverage.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Check for rtc_class_ops structures that are only passed to
devm_rtc_device_register, rtc_device_register,
platform_device_register_data, all of which declare the corresponding
parameter as const. Declare rtc_class_ops structures that have these
properties as const.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct rtc_class_ops i@p = { ... };
@ok@
identifier r.i;
expression e1,e2,e3,e4;
position p;
@@
(
devm_rtc_device_register(e1,e2,&i@p,e3)
|
rtc_device_register(e1,e2,&i@p,e3)
|
platform_device_register_data(e1,e2,e3,&i@p,e4)
)
@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct rtc_class_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The ac100 device tree binding specifies the usage of clock-output-names
to specify the names of its 3 clock outputs. This is needed for orphan
clock resolution, when the ac100 is probed much later than any clocks
that consume any of its outputs. This wasn't supported by the driver.
Add support for this.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The field "owner" is set by core. Thus delete an extra initialisation.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
While the oscillator failure flag is set, the RTC registers
should be considered invalid. bq32k_rtc_read_time() now
returns an error instead of an invalid time.
The failure flag is cleared the next time the clock is set.
Signed-off-by: Jan Östlund <jao@hms.se>
Signed-off-by: Daniel Romell <daro@hms.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The BQ32K_SECONDS_MASK and BQ32K_MINUTES_MASK both has the same
value. This is no functional change.
Signed-off-by: Jan Östlund <jao@hms.se>
Signed-off-by: Daniel Romell <daro@hms.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The char pointer buf_ptr is assigned an address from a const char
pointer buf (parameter of wakealarm_store).
The data pointer by buf_ptr is never modified.
So casting it to a (char *) is useless.
This patch remove this cast, and transform buf_ptr to a const char pointer.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The Intersil isl12057 is now supported by the ds1307 driver.
Acked-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Intersil ISL12057 is a drop-in replacement for DS1337. It can be supported
by the ds1307 driver.
Acked-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add an option to properly support the century bit of ds1337 and compatibles
and ds1340.
Because the driver had a bug until now, it is not possible to switch users
to the fixed code directly as RTCs in the field will wrongly have the
century bit set.
Acked-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
It is likely that checking the result of 'pcf2123_write_reg' is expected
here.
Also fix a small style issue. The '{' at the beginning of the function
is misplaced.
Fixes: 809b453b76 ("rtc: pcf2123: clean up writes to the rtc chip")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The RK808 and RK818 PMICs are using a similar register map.
We can reuse the rtc driver for the RK818 PMIC. So let's add
the RK818 in the Kconfig description.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In order to support RTC on Qualcomm MDM9615 SoC, add support for
the pm8018 rtc in rtc-pm8xxx driver.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The AC100's RTC side has 3 clock outputs on external pins, which can
provide a clock signal to the SoC or other modules, such as WiFi or
GSM modules.
Support this with a custom clk driver integrated with the rtc driver.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
X-Powers AC100 is a codec / RTC combo chip. This driver supports
the RTC sub-device.
The RTC block also has clock outputs and non-volatile storage.
Non-volatile storage wthin the RTC hardware is not supported.
Clock output support is added in the next patch.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cleanups:
- huge cleanup of rtc-generic and char/genrtc this allowed to cleanup rtc-cmos,
rtc-sh, rtc-m68k, rtc-powerpc and rtc-parisc
- move mn10300 to rtc-cmos
Subsystem:
- fix wakealarms after hibernate
- multiples fixes for rctest
- simplify implementations of .read_alarm
New drivers:
- Maxim MAX6916
Drivers:
- ds1307: fix weekday
- m41t80: add wakeup support
- pcf85063: add support for PCF85063A variant
- rv8803: extend i2c fix and other fixes
- s35390a: fix alarm reading, this fixes instant reboot after shutdown for QNAP
TS-41x
- s3c: clock fixes
-----BEGIN PGP SIGNATURE-----
iQIcBAABCgAGBQJXokhIAAoJENiigzvaE+LCZqQP+wWzintN/N1u3dKiVB7iSdwq
+S/jAXD9wW8OK9PI60/YUGRYeUXmZW9t4XYg1VKCxU9KpVC17LgOtDyXD8BufP1V
uREJEzZw9O7zCCjeHp/ICFjBkc62Net6ZDOO+ZyXPNfddpS1Xq1uUgXLZc/202UR
ID/kewu0pJRDnoxyqznWn9+8D33w/ygXs2slY2Ive0ONtjdgxGcsj2rNbb2RYn2z
OP7br3lLg7qkFh4TtXb61eh/9GYIk6wzP/CrX5l/jH4SjQnrIk5g/X/Cd1qQ/qso
JZzFoonOKvIp5Gw/+fZ9NP3YFcnkoRMv4NjZV8PAmsYLds+ibRiBcoB8u6FmiJV7
WW5uopgPkfCGN5BV3+QHwJDVe+WlgnlzaT5zPUCcP5KWusDts4fWIgzP7vrtAzf4
3OJLrgSGdBeOqWnJD21nxKUD27JOseX7D+BFtwxR4lMsXHqlHJfETpZ8gts1ZGH3
2U353j/jkZvGWmc6dMcuxOXT2K4VqpYeIIqs0IcLu6hM9crtR89zPR2Iu1AilfDW
h2NroF+Q//SgMMzWoTEG6Tn7RAc7MthgA/tRCFZF9CBMzNs988w0CTHnKsIHmjpU
UKkMeJGAC9YrPYIcqrg0oYsmLUWXc8JuZbGJBnei3BzbaMTlcwIN9qj36zfq6xWc
TMLpbWEoIsgFIZMP/hAP
=rpGB
-----END PGP SIGNATURE-----
Merge tag 'rtc-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"RTC for 4.8
Cleanups:
- huge cleanup of rtc-generic and char/genrtc this allowed to cleanup
rtc-cmos, rtc-sh, rtc-m68k, rtc-powerpc and rtc-parisc
- move mn10300 to rtc-cmos
Subsystem:
- fix wakealarms after hibernate
- multiples fixes for rctest
- simplify implementations of .read_alarm
New drivers:
- Maxim MAX6916
Drivers:
- ds1307: fix weekday
- m41t80: add wakeup support
- pcf85063: add support for PCF85063A variant
- rv8803: extend i2c fix and other fixes
- s35390a: fix alarm reading, this fixes instant reboot after
shutdown for QNAP TS-41x
- s3c: clock fixes"
* tag 'rtc-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (65 commits)
rtc: rv8803: Clear V1F when setting the time
rtc: rv8803: Stop the clock while setting the time
rtc: rv8803: Always apply the I²C workaround
rtc: rv8803: Fix read day of week
rtc: rv8803: Remove the check for valid time
rtc: rv8803: Kconfig: Indicate rx8900 support
rtc: asm9260: remove .owner field for driver
rtc: at91sam9: Fix missing spin_lock_init()
rtc: m41t80: add suspend handlers for alarm IRQ
rtc: m41t80: make it a real error message
rtc: pcf85063: Add support for the PCF85063A device
rtc: pcf85063: fix year range
rtc: hym8563: in .read_alarm set .tm_sec to 0 to signal minute accuracy
rtc: explicitly set tm_sec = 0 for drivers with minute accurancy
rtc: s3c: Add s3c_rtc_{enable/disable}_clk in s3c_rtc_setfreq()
rtc: s3c: Remove unnecessary call to disable already disabled clock
rtc: abx80x: use devm_add_action_or_reset()
rtc: m41t80: use devm_add_action_or_reset()
rtc: fix a typo and reduce three empty lines to one
rtc: s35390a: improve two comments in .set_alarm
...
V1F indicates that the time accuracy may have been compromised because
of a voltage drop (possibly only temporary) below VLOW1, which stops the
temperature compensation. When the time is set, the accuracy is
restored, so V1F should be cleared in order to indicate this and to be
able to detect the next temperature compensation loss. This is the same
principle as for V2F, which is cleared when the time is set to indicate
that the time is no longer invalid and to be able to detect the next
data loss.
Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
According to the application manual of the RX8900, the RESET bit must be
set to 1 to prevent a timer update while setting the time. This also
resets the subsecond counter. The application manual of the RV-8803 does
not mention such a requirement, and it says that the 100th Seconds
register is cleared when writing to the Seconds register, but using the
RESET bit for the RV-8803 too should not be an issue and is probably
safer.
This change also ensures that the RESET bit is initialized properly in
all cases. Indeed, all the registers must be initialized if the voltage
has been lower than VLOW2 (triggering V2F), but not low enough to
trigger a POR.
Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The I²C NACK issue of the RV-8803 may occur after any I²C START
condition, depending on the timings. Consequently, the workaround must
be applied for all the I²C transfers.
This commit abstracts the I²C transfer code into register access
functions. This avoids duplicating the I²C workaround everywhere. This
also avoids the duplication of the code handling the return value of
i2c_smbus_read_i2c_block_data(). Error messages are issued in case of
definitive register access failures (if the workaround fails). This
change also makes the I²C transfer return value checks consistent.
Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The Weekday register is encoded as 2^tm_wday, with tm_wday in 0..6, so
using tm_wday = ffs(reg) to fill tm_wday from the register value is
wrong because this gives the expected value + 1. This could be fixed as
tm_wday = ffs(reg) - 1, but tm_wday = ilog2(reg) works as well and is
more direct.
Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The RTC core always calls rtc_valid_tm() after ->read_time() in case of
success (in __rtc_read_time()), so do not call it twice.
Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This driver supports the Epson RX8900, but this was not indicated in
Kconfig.
Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Remove .owner field if calls are used which set it automatically.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The driver allocates the spinlock but not initialize it.
Use spin_lock_init() on it to initialize it correctly.
This is detected by Coccinelle semantic patch.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Allow the alarm IRQ of RTC to be used as a wakeup source for the system
suspend.
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
It should be a real error message, when the driver cannot enable the IRQ
of the device.
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The current rtc-pcf85063 driver only supports the PCF85063TP device.
Using the existing driver on a PCF85063A will result in the time being
set correctly into the RTC, but the RTC is held in the stopped state.
Therefore, the time will no longer advance and no error is indicated.
The PCF85063A device has a bigger memory map than the PCF85063TP.
The existing driver make use of an address rollover condition,
but the rollover point is different in the two devices.
Signed-off-by: Chris DeBruin <cdeb5783@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The year range is not validated properly
As the driver has been mainlined in 2014, it is not an issue to stop
handling dates between 1970 and 2000 with the benefit of handling dates up
to 2100.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
