Since clock stop causes bus reset on Intel controllers, we need
to wait for the debounce interval on resume, to ensure all the
interrupt status registers are set correctly.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230127165111.3010960-9-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
idle_bias_on was set because cs42l42 has a "VMID" type pseudo-midrail
supply (named FILT+), and these typically take a long time to charge.
But the driver never enabled pm_runtime so it would never have powered-
down the cs42l42 anyway.
In fact, FILT+ can charge to operating voltage within 12.5 milliseconds
of enabling HP or ADC. This time is already covered by the startup
delay of the HP/ADC.
The datasheet warning about FILT+ taking up to 1 second to charge only
applies in the special cases that either the PLL is started or
DETECT_MODE set to non-zero while both HP and ADC are off. The driver
never does either of these.
Removing idle_bias_on allows the Soundwire host controller to suspend
if there isn't a snd_soc_jack handler registered.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230127165111.3010960-8-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds support for using CS42L42 as a SoundWire device.
SoundWire-specifics are kept separate from the I2S implementation as
much as possible, aiming to limit the risk of breaking the I2C+I2S
support.
There are some important differences in the silicon behaviour between
I2S and SoundWire mode that are reflected in the implementation:
- ASP (I2S) most not be used in SoundWire mode because the two interfaces
share pins.
- The SoundWire capture (record) port only supports 1 channel. It does
not have left-to-right duplication like the ASP.
- DP2 can only be prepared if the HP has powered-up. DP1 can only be
prepared if the ADC has powered-up. (This ordering restriction does
not exist for ASPs.) The SoundWire core port-prepare step is
triggered by the DAI-link prepare(). This happens before the
codec DAI prepare() or the DAPM sequence so these cannot be used
to enable HP/ADC. Instead the HP/ADC enable/disable are done during
the port_prep callback.
- The SRCs are an integral part of the audio chain but in silicon their
power control is linked to the ASP. There is no equivalent power link
to SoundWire DPs so the driver must take "manual" control of SRC power.
- The SoundWire control registers occupy the lower part of the SoundWire
address space so cs42l42 registers are offset by 0x8000 (non-paged) in
SoundWire mode.
- Register addresses are 8-bit paged in I2C mode but 16-bit unpaged in
SoundWire.
- Special procedures are needed on register read/writes to (a) ensure
that the previous internal bus transaction has completed, and
(b) handle delayed read results, when the read value could not be
returned within the SoundWire read command.
There are also some differences in driver implementation between I2S
and SoundWire operation:
- CS42L42 I2S does not runtime_suspend, but runtime_suspend/resume support
has been added into the driver in SoundWire mode as the most convenient
way to power-up the bus manager and to handle the unattach_request
condition, though the CS42L42 chip does not itself suspend or resume.
- Intel SoundWire host controllers have a low-power clock-stop mode that
requires resetting all peripherals when resuming. This means that the
interrupt registers will be reset in between the interrupt being
generated and the interrupt being handled, and since the interrupt
status is debounced, these values may not be accurate immediately,
and may cause spurious unplug events before settling.
- As in I2S mode, the PLL is only used while audio is active because
of clocking quirks in the silicon. For SoundWire the cs42l42_pll_config()
is deferred until the DAI prepare(), to allow the cs42l42_bus_config()
callback to set the SCLK.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230127165111.3010960-7-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Export functions that will be needed by a SoundWire module.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230127165111.3010960-6-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Setup of the ASP (audio serial port) was being done as a side-effect of
cs42l42_pll_config() and forces a restriction on the ratio of sample_rate
to bit_clock that is invalid for Soundwire.
Move the ASP setup into a dedicated function.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230127165111.3010960-5-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The chosen clocking configuration must give an internal MCLK (MCLKint)
that is an integer multiple of the sample rate.
On I2S each of the supported bit clock frequencies can only be generated
from one sample rate group (either the 44100 or the 48000) so the code
could use only the bitclock to look up a PLL config.
The relationship between sample rate and bitclock frequency is more
complex on Soundwire and so it is possible to set a frame shape to
generate a bitclock from the "wrong" group. For example 2*147 with a
48000 sample rate would give a bitclock of 14112000 which on I2S
could only be derived from a 44100 sample rate.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230127165111.3010960-4-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The SOFT_RESET_REBOOT register is needed to recover CS42L42 state after
a Soundwire bus reset.
This is required to be set whenever there is severe/hard bus reset.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230127165111.3010960-3-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current snd_soc_dai has data for Playback/Capture, but it is very
random. Someone is array (A), someone is playback/capture (B),
and someone is tx/rx (C);
struct snd_soc_dai {
...
(A) unsigned int stream_active[SNDRV_PCM_STREAM_LAST + 1];
(B) struct snd_soc_dapm_widget *playback_widget;
(B) struct snd_soc_dapm_widget *capture_widget;
(B) void *playback_dma_data;
(B) void *capture_dma_data;
...
(C) unsigned int tx_mask;
(C) unsigned int rx_mask;
};
Because of it, the code was very complicated.
This patch creates new data structure to merge these into one,
and tidyup the code.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/87cz6vea1v.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ASoC has many helper function.
This patch use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/87fsbrea25.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ASoC has many helper function.
This patch use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/87ilgnea2p.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ASoC has many helper function.
This patch use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/87k013ea2u.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ASoC has many helper function.
This patch use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/87r0vbea3r.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ASoC has many helper function.
This patch use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/87sffrea3z.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>:
Following is series of fixes and cleanups for core topology code. Few
patches fixing various problems all around and few fixing function
names.
The Awinic AW88395 is an I2S/TDM input, high efficiency
digital Smart K audio amplifier with an integrated 10.25V
smart boost convert
Signed-off-by: Nick Li <liweilei@awinic.com>
Signed-off-by: Bruce zhao <zhaolei@awinic.com>
Signed-off-by: Weidong Wang <wangweidong.a@awinic.com>
Link: https://lore.kernel.org/r/20230113055301.189541-5-wangweidong.a@awinic.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Awinic AW88395 is an I2S/TDM input, high efficiency
digital Smart K audio amplifier with an integrated 10.25V
smart boost convert
Signed-off-by: Nick Li <liweilei@awinic.com>
Signed-off-by: Bruce zhao <zhaolei@awinic.com>
Signed-off-by: Ben Yi <yijiangtao@awinic.com>
Signed-off-by: Weidong Wang <wangweidong.a@awinic.com>
Link: https://lore.kernel.org/r/20230113055301.189541-4-wangweidong.a@awinic.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Awinic AW88395 is an I2S/TDM input, high efficiency
digital Smart K audio amplifier with an integrated 10.25V
smart boost convert
Signed-off-by: Nick Li <liweilei@awinic.com>
Signed-off-by: Bruce zhao <zhaolei@awinic.com>
Signed-off-by: Weidong Wang <wangweidong.a@awinic.com>
Link: https://lore.kernel.org/r/20230113055301.189541-3-wangweidong.a@awinic.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Awinic AW88395 is an I2S/TDM input, high efficiency
digital Smart K audio amplifier with an integrated 10.25V
smart boost convert
Signed-off-by: Nick Li <liweilei@awinic.com>
Signed-off-by: Bruce zhao <zhaolei@awinic.com>
Signed-off-by: Weidong Wang <wangweidong.a@awinic.com>
Link: https://lore.kernel.org/r/20230113055301.189541-2-wangweidong.a@awinic.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Renesas IDT821034 codec is four channel PCM codec with on-chip
filters and programmable gain setting.
It also provides SLIC (Subscriber Line Interface Circuit) signals as
GPIOs.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Link: https://lore.kernel.org/r/20230126085137.375814-3-herve.codina@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add runtime PM support for Microchip SPDIFRX driver. On runtime suspend
the clocks are disabled and regmap is set in caching mode. On runtime
resume the clocks are enabled and regmap is synced with the device.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230130120647.638049-8-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
CSC interrupts which might be used in controls are on bits 8 and 9 of
SPDIFRX_IDR register. Thus disable all the interrupts that are exported
by driver.
Fixes: ef265c55c1 ("ASoC: mchp-spdifrx: add driver for SPDIF RX")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230130120647.638049-5-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Channel status get and channel subcode get controls relies on data
returned by controls when certain IRQs are raised. To achieve that
completions are used b/w controls and interrupt service routine. The
concurrent accesses to these controls are protected by
struct snd_card::controls_rwsem.
Issues identified:
- reinit_completion() may be called while waiting for completion
which should be avoided
- in case of multiple threads waiting, the complete() call in interrupt
will signal only one waiting thread per interrupt which may lead to
timeout for the others
- in case of channel status get as the CSC interrupt is not refcounted
ISR may disable interrupt for threads that were just enabled it.
To solve these the access to controls were protected by a mutex. Along
with this there is no need for spinlock to protect the software cache
reads/updates b/w controls and ISR as the update is happening only when
requested from control, and only one reader can reach the control.
Fixes: ef265c55c1 ("ASoC: mchp-spdifrx: add driver for SPDIF RX")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230130120647.638049-4-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
wait_for_completion_interruptible_timeout() returns 0 in case of
timeout. Check this into account when returning from function.
Fixes: ef265c55c1 ("ASoC: mchp-spdifrx: add driver for SPDIF RX")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230130120647.638049-3-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPDIFRX block is clocked by 2 clocks: peripheral and generic clocks.
Peripheral clock feeds user interface (registers) and generic clock feeds
the receiver.
To enable the receiver the generic clock needs to be enabled and also the
ENABLE bit of MCHP_SPDIFRX_MR register need to be set.
The signal control exported by mchp-spdifrx driver reports wrong status
when the receiver is disabled. This can happen when requesting the signal
and the capture was not previously started. To solve this the receiver
needs to be enabled (by enabling generic clock and setting ENABLE bit of
MR register) before reading the signal status.
As with this fix there are 2 paths now that need to control the generic
clock and ENABLE bit of SPDIFRX_MR register (one path though controls, one
path though configuration) a mutex has been introduced. We can't rely on
subsystem locking as the controls are protected by
struct snd_card::controls_rwsem semaphore and configuration is protected
by a different lock (embedded in snd_pcm_stream_lock_irq()).
The introduction of mutex is also extended to other controls which rely on
SPDIFRX_RSR.ULOCK bit as it has been discovered experimentally that having
both clocks enabled but not the receiver (through ENABLE bit of SPDIFRX.MR)
leads to inconsistent values of SPDIFRX_RSR.ULOCK. Thus on some controls we
rely on software state (dev->trigger_enabled protected by mutex) to
retrieve proper values.
Fixes: ef265c55c1 ("ASoC: mchp-spdifrx: add driver for SPDIF RX")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230130120647.638049-2-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
struct snd_soc_dobj only needs pointer to the unload function, instead
however, there is pointer to all topology operations. Change code to use
the function pointer instead of pointer to structure containing all
operations.
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230127231111.937721-12-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Functions removing bytes, enum and mixer kcontrols are identical. Unify
them under one function and use it to free associated kcontrols.
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230127231111.937721-11-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Caller already checks if hdr_pos is behind EOF, before calling
soc_tplg_valid_header(), so there is no need to recheck it again. This
also allows to remove behaviour of return 0 - forcing the caller to
break out of while loop.
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230127231111.937721-10-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Function soc_tplg_dapm_complete() detects an error and logs it, but
doesn't return failure to the caller, fix it by returning the error.
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230127231111.937721-9-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of passing address of structure, the containing structure is
cast to target structure. While it works - the expected structure is the
first field of containing one - it is bad practice, fix this by passing
pointer to structure field.
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230127231111.937721-8-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no need to forward declare functions if their use is after
their definition.
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230127231111.937721-7-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Those are the only functions missing soc_tplg_ prefix, add it for
consistency.
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230127231111.937721-6-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Functions other than soc_valid_header have soc_tplg_ prefix. Rename
function to follow convention in file.
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230127231111.937721-5-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Topology is being abbreviated to "tplg", not "tplc", however, few
functions have typo in name, fix it.
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230127231111.937721-4-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The constant is unused, so it can be safely removed.
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230127231111.937721-3-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the reserved bit 7 in the ANALOG_CTRL_REG for the TAS5720A-Q1 device,
when probing.
The datasheet mentions that the bit should be 1 during reset/powerup.
The device did not initialize before setting this value to 1. So, this
could be a quirk of this device. Or it could be a quirk with the board on
which it was tested.
That is why this patch is separate from the patch that adds support for the
TAS5720A-Q1 device.
Signed-off-by: Steffen Aschbacher <steffen.aschbacher@stihl.de>
Signed-off-by: Alexandru Ardelean <alex@shruggie.ro>
Link: https://lore.kernel.org/r/20230128082744.41849-3-alex@shruggie.ro
Signed-off-by: Mark Brown <broonie@kernel.org>
This change adds support the TAS5720A-Q1 audio codec, in the same driver as
tas5720.
Functionally, this driver is pretty similar to it's TAS5720x variant.
The first 3 registers are the same, so the main control and device
identification can happen with these registers.
The next registers differ.
This variant offers control (in the registers) for 2 speakers, which is
implemented here (in a basic manner).
Signed-off-by: Steffen Aschbacher <steffen.aschbacher@stihl.de>
Signed-off-by: Alexandru Ardelean <alex@shruggie.ro>
Link: https://lore.kernel.org/r/20230128082744.41849-2-alex@shruggie.ro
Signed-off-by: Mark Brown <broonie@kernel.org>
This is to be re-used in tas5720_mute() (which is part of the dai_ops) and
also in the tas5720_fault_check_work() hook.
The benefit here isn't too great (now).
It's only when we add support for a new device with a slightly different
regmap that this becomes more useful.
Signed-off-by: Alexandru Ardelean <alex@shruggie.ro>
Link: https://lore.kernel.org/r/20230128082744.41849-1-alex@shruggie.ro
Signed-off-by: Mark Brown <broonie@kernel.org>
Refactor bit width calculation using params_physical_width()
instead hard-code values.
Signed-off-by: Venkata Prasad Potturu <venkataprasad.potturu@amd.com>
Link: https://lore.kernel.org/r/20230130100104.4076640-1-venkataprasad.potturu@amd.com
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Walking the dram->cs array was seen as accesses beyond the first array
item by the compiler. Instead, use the array index directly. This allows
for run-time bounds checking under CONFIG_UBSAN_BOUNDS as well. Seen
with GCC 13 with -fstrict-flex-arrays:
../sound/soc/kirkwood/kirkwood-dma.c: In function
'kirkwood_dma_conf_mbus_windows.constprop':
../sound/soc/kirkwood/kirkwood-dma.c:90:24: warning: array subscript 0 is outside array bounds of 'const struct mbus_dram_window[0]' [-Warray-bounds=]
90 | if ((cs->base & 0xffff0000) < (dma & 0xffff0000)) {
| ~~^~~~~~
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: alsa-devel@alsa-project.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20230127224128.never.410-kees@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Peter Ujfalusi <peter.ujfalusi@linux.intel.com>:
The following series will enable multi-stream support for playback and capture
streams.
Currently only a single PCM can be connected to a DAI, with the multi-stream
support it is possible to connect multiple PCMs to a single DAI.
To achieve this we need to make sure that DAIs/AIF are only set up once since
other stream could be connected to it later.
We also need to introduce reference or use counting for widgets to make sure
that they are not going to be destroyed while other streams are still using
them.
With the multi-stream support we also need to extend our current locking scheme
which worked well for simple paths.
Merge series from Astrid Rost <astrid.rost@axis.com>:
Add a generic way to create jack inputs for auxiliary jack detection
drivers (e.g. via i2c, spi), which are not part of any real codec.
The simple-card can be used as combining card driver to add the jacks,
no new one is required.
Create a jack (for input-events) for jack devices in the auxiliary
device list (aux_devs). A device which returns a valid value on
get_jack_type counts as jack device; set_jack is required
to add the jack to the device.
Add a generic way to create jack inputs for auxiliary jack detection
drivers (e.g. via i2c, spi), which are not part of any real codec.
The simple-card can be used as combining card driver to add the jacks,
no new one is required.
Create a jack (for input-events) for jack devices in the auxiliary
device list (aux_devs). A device which returns a valid value on
get_jack_type counts as jack device; set_jack is required
to add the jack to the device.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230123135913.2720991-3-astrid.rost@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add function to return the jack type of snd_jack_types.
This allows a generic card driver to add a jack with the specified
type.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230123135913.2720991-2-astrid.rost@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If the pipeline setup fails at the first widget/pipeline then we will have
no spipe stored under the pipeline_list->pipelines, the
pipeline_list->count is 0.
If this is the case we would have a NULL pointer dereference if the
execution is allowed to proceed.
Check for this condition along with the pipeline_list->pipelines check
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-19-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The use_count of the swidget is protect by ALSA core PCM locking with the
exception when an associated kcontrol is changed.
It has been observed that a rightly timed kcontrol access during stream
stop can result of an attempt to send a control update to a widget which
has been freed up between the check of the use_count and the message
sending.
We need to protect the entire sof_widget_setup() and sof_widget_free()
execution to make it safe to rely on the use_count.
Move the code under an _unlocked() function and use a mutex to protect
the execution of the functions for concurrency.
On the control path we need to use the lock only for the kcontrol access,
the widget_kcontrol_setup() op is called with the lock already held.
Reported-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-18-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The sof_widget_free() on the error path will decrement the use count and if
we jump to widget_free: then the use_count will be decremented by two,
which is not correct as we only incremented once with 1.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-17-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When starting/stopping multiple streams in parallel, pipeline triggers
and pipeline frees can get interleaved. So use the same mutex used for
pipeline trigger to protect the pipeline frees as well. Rename the
trigger_mutex to pipeline_state_mutex for more clarity.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-16-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the started_count and paused_count to implement reference counting
when making decisions to start/stop/pause pipelines during the FE DAI
trigger. This is necessary to trigger the shared pipelines in the FE DAI
trigger properly.
With IPC4, the FE trigger will issue multiple pipeline state changes,
and the triggers are propagated downstream to connected pipelines by
the SOF driver - not the firmware. This creates a window for race
conditions where an FE trigger preempts another one, which results
in inconsistent pipeline states and refcounts.
This patch introduces a mutex lock for the pcm trigger that guarantees
that IPC4 state and resources are accessed in a serialized manner.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-15-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For more clarity, rename the struct ipc4_pipeline_set_state_data
variable to trigger_list instead of data. No functionality change.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-14-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Introduce struct snd_sof_pipeline to save the information about
pipelines including the pipeline widget, their status wrt how many PCM's
are using them and whether they are complete or not.
In struct snd_sof_widget, replace pipe_widget with spipe and remove
complete. In struct snd_sof_pcm_stream_pipeline_list, replace
pipe_widgets with pipelines.
Update all users accordingly.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-13-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the list of pipelines in the PCM stream's pipeline info to trigger
the pipelines in the right order. Add a helper for triggering pipelines
in batch mode that will be used to trigger multiple pipelines at the
same time.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Libin Yang <libin.yang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-12-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Populate the pipeline_info for the PCM stream with the list of pipeline
widgets that need to be handled during the PCM trigger. This will be
used in the IPC-specific PCM trigger op to trigger the pipelines.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Libin Yang <libin.yang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-11-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a new flag, skip_during_fe_trigger, to struct sof_ipc4_pipeline to
skip triggering pipelines in the FE DAI trigger. Set this flag for the
HDA DAI BE pipelines so that their BE pipeline will not be triggered in
the FE DAI trigger. Also, move the trigger handling for all commands
include START/PAUSE_RELEASE for the HDA DAI's to the backend DAI trigger
ops.
For the SSP/DMIC/SDW cases, remove the BE DAI trigger as they involve no
DMA operations and can be triggered in the FE DAI trigger. This is in
preparation to perform batch triggering of all pipelines for the non-HDA
case.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Libin Yang <libin.yang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-10-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Define the pcm_setup/pcm_free ops for IPC4. Define a new struct
snd_sof_pcm_stream_trigger_info and add a new field trigger_info of this
type to struct snd_sof_pcm_stream. This will be used to save the list of
pipelines that need to be triggered.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Libin Yang <libin.yang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-9-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
These will be used to perform IPC-specific PCM setup/free.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Libin Yang <libin.yang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-8-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a new topology IPC op to set up DAI links and set the link trigger
order to match the expectation based on the IPC type. Note that the
link_setup op implementations for IPC3 and IPC4 are not identical and
have contrasting trigger orders for playback and capture.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-7-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
IPC3 and IPC4 have different requirements for the order in which the FE
CPU and BE CPU DAI trigger callbacks must be invoked. With a regular PCM
start/stop, pipeline widgets are set up during hw_params and freed
during hw_free.
But when the system is suspended when a PCM is running,
pipeline widgets are freed during the SUSPEND trigger callback for the
FE CPU DAI. In order to avoid freeing the pipeline widgets before the BE
CPU DAI trigger is executed, the trigger order was modified in previous
contributions in the PCM dai_link_fixup callback to make sure that the BE
CPU DAI trigger stop/suspend is always invoked before the FE CPU DAI
trigger. But this contradicts the firmware requirement for IPC4 w.r.t.
ordering of pipeline triggers.
So, remove the freeing of pipeline widgets during FE CPU DAI suspend
trigger and handle it during system suspend when the
tear_down_all_pipelines() IPC op is invoked. This will be followed up
with a patch to fix the trigger order for IPC4.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-6-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When walking the list of the widgets from the source to the sink, we
accidentally also end up preparing/setting up the widgets that are not
in the list of connected DAPM widgets associated with the PCM. Avoid
this by checking if a widget is part of the connected DAPM widget list
during widget prepare, unprepare, setup or free.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-5-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Calling the sof_widget_setup/free() for the DAI/AIF widgets inside the
snd_soc_dapm_widget_for_each_sink_path() loop will end up setting up or
freeing the widget multiple times if there are multiple paths leaving
the widget. Fix this by moving the widget setup/free for the starting
widget in each path outside the loop.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-4-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Export the widget_in_list() function to be used by other modules.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The FW currently ignores unbinding routes if the source and sink widgets
belong to the same pipeline. So no need to send the IPC at all in the
first place.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If panic_on_warn is set and compress stream(DPCM) is started,
then kernel panic occurred because card->pcm_mutex isn't held appropriately.
In the following functions, warning were issued at this line
"snd_soc_dpcm_mutex_assert_held".
static int dpcm_be_connect(struct snd_soc_pcm_runtime *fe,
struct snd_soc_pcm_runtime *be, int stream)
{
...
snd_soc_dpcm_mutex_assert_held(fe);
...
}
void dpcm_be_disconnect(struct snd_soc_pcm_runtime *fe, int stream)
{
...
snd_soc_dpcm_mutex_assert_held(fe);
...
}
void snd_soc_runtime_action(struct snd_soc_pcm_runtime *rtd,
int stream, int action)
{
...
snd_soc_dpcm_mutex_assert_held(rtd);
...
}
int dpcm_dapm_stream_event(struct snd_soc_pcm_runtime *fe, int dir,
int event)
{
...
snd_soc_dpcm_mutex_assert_held(fe);
...
}
These functions are called by soc_compr_set_params_fe, soc_compr_open_fe
and soc_compr_free_fe
without pcm_mutex locking. And this is call stack.
[ 414.527841][ T2179] pc : dpcm_process_paths+0x5a4/0x750
[ 414.527848][ T2179] lr : dpcm_process_paths+0x37c/0x750
[ 414.527945][ T2179] Call trace:
[ 414.527949][ T2179] dpcm_process_paths+0x5a4/0x750
[ 414.527955][ T2179] soc_compr_open_fe+0xb0/0x2cc
[ 414.527972][ T2179] snd_compr_open+0x180/0x248
[ 414.527981][ T2179] snd_open+0x15c/0x194
[ 414.528003][ T2179] chrdev_open+0x1b0/0x220
[ 414.528023][ T2179] do_dentry_open+0x30c/0x594
[ 414.528045][ T2179] vfs_open+0x34/0x44
[ 414.528053][ T2179] path_openat+0x914/0xb08
[ 414.528062][ T2179] do_filp_open+0xc0/0x170
[ 414.528068][ T2179] do_sys_openat2+0x94/0x18c
[ 414.528076][ T2179] __arm64_sys_openat+0x78/0xa4
[ 414.528084][ T2179] invoke_syscall+0x48/0x10c
[ 414.528094][ T2179] el0_svc_common+0xbc/0x104
[ 414.528099][ T2179] do_el0_svc+0x34/0xd8
[ 414.528103][ T2179] el0_svc+0x34/0xc4
[ 414.528125][ T2179] el0t_64_sync_handler+0x8c/0xfc
[ 414.528133][ T2179] el0t_64_sync+0x1a0/0x1a4
[ 414.528142][ T2179] Kernel panic - not syncing: panic_on_warn set ...
So, I reposition and add pcm_mutex to resolve lockdep error.
Signed-off-by: Shinhyung Kang <s47.kang@samsung.com>
Link: https://lore.kernel.org/r/016401d90ac4$7b6848c0$7238da40$@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
I'm not exactly clear on what strange workflow causes people to do it,
but clearly occasionally some files end up being committed as executable
even though they clearly aren't.
This is a reprise of commit 90fda63fa1 ("treewide: fix up files
incorrectly marked executable"), just with a different set of files (but
with the same trivial shell scripting).
So apparently we need to re-do this every five years or so, and Joe
needs to just keep reminding me to do so ;)
Reported-by: Joe Perches <joe@perches.com>
Fixes: 523375c943 ("drm/vmwgfx: Port vmwgfx to arm64")
Fixes: 5c43993777 ("ASoC: codecs: add support for ES8326")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While looking through legacy platform data users, I noticed that
the DT probing never uses data from the DT properties, as the
platform_data structure gets overwritten directly after it
is initialized.
There have never been any boards defining the platform_data in
the mainline kernel either, so this driver so far only worked
with patched kernels or with the default values.
For the benefit of possible downstream users, fix the DT probe
by no longer overwriting the data.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230126162203.2986339-1-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
We know that "irq < 0", so delete the unnecessary check.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/Y9JHSwcfdNcfMjjt@kili
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, we use the same channel mask for aggregated speakers.
It works fine for playback because we duplicate the audio data for all
aggregated speakers. But we need to get audio data from each aggregated
speaker and combine them to the captured audio. So we need to set
non-overlapping channel mask for aggregated ALH DAIs.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230125141317.30302-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The corresponding IPC4 module of snd_soc_dapm_buffer widget is module
-to-module copier.
The module-to-module copier is a buffer-like component with demuxing
capabilities.
Rename the host_token_list to common_copier_token_list since it will
be used by host copier and module-to-module copier.
The setup callback is almost the same as sof_ipc4_widget_setup_pcm except
the gtw_cfg data, and the free callback is exactly the same as
sof_ipc4_widget_free_comp_pcm. To reduce the duplication, the commit
reuses the setup and free callbacks.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230126110637.25542-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace SNDRV_DMA_TYPE_DEV by SNDRV_DMA_TYPE_NONCOHERENT for pcm
buffer allocation. We measured about 18x performance improvement
when accessing the snd_pcm_mmap() buffer from userspace.
Eg: aarch64 with internal speaker
==
SNDRV_DMA_TYPE_DEV
frames_per_second=66.4557M/s
max_time_per_4096_frames=106.094u
time_per_4096_frames=61.6351us
SNDRV_DMA_TYPE_NONCOHERENT
frames_per_second=1028.58M/s
max_time_per_4096_frames=20.312u
time_per_4096_frames=3.98221us
Signed-off-by: Judy Hsiao <judyhsiao@chromium.org>
Link: https://lore.kernel.org/r/20221208084200.2136311-1-judyhsiao@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
If all devices are the same or compatible, there is no single need to
keep growing of_device_id list with new entries.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230118101542.96705-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Correct reversed values used in min/max rates, leading to incorrect
playback constraints.
Cc: <stable@vger.kernel.org>
Fixes: 43b8c7dc85 ("ASoC: codecs: add wsa883x amplifier support")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230124123049.285395-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no need for the probe-component to be part of the PCM component
list as it does not make use of ASoC-topology and does not participate
in creating any PCM streams.
To achieve that, remove probe() and remove() functions.
Fixes: ed914a2a45 ("ASoC: Intel: avs: Data probing soc-component")
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20230123122144.1356890-1-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Check for SPF readiness in prm driver probe to avoid race conditions
during ADSP pil loading.
This patch is to avoid, sending requests to ADSP before it's
power domains are up and ready.
Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Tested-by: Ratna Deepthi Kudaravalli <rkudarav@qti.qualcomm.com>
Link: https://lore.kernel.org/r/1673508617-27410-1-git-send-email-quic_srivasam@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This model requires an additional detection quirk to enable the
internal microphone - BIOS doesn't seem to support AcpDmicConnected
(nothing in acpidump output).
Signed-off-by: fengwk <fengwk94@gmail.com>
Link: https://lore.kernel.org/r/Y8wmCutc74j/tyHP@arch
Signed-off-by: Mark Brown <broonie@kernel.org>
If the swidget is NULL we skip the preparing of the widget and jump to
handle the sink path of the widget.
If the prepare fails in this case we would undo the prepare but the swidget
is NULL (we skipped the prepare for the widget).
To avoid NULL pointer dereference in this case we must check swidget
against NULL pointer once again.
Fixes: 0ad84b11f2 ("ASoC: SOF: sof-audio: skip prepare/unprepare if swidget is NULL")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230120102125.30653-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Kai Vehmanen <kai.vehmanen@linux.intel.com>:
This series addresses problems with echo reference devices
reported in:
"[BUG][ADL-N] Kernel panic when echo reference stream is opened"
https://github.com/thesofproject/linux/issues/4083
ux500_pcm_request_chan() is never called because the dma channels
are already set up from DT. Remove this, along with the
ux500_msp_dma_params structure.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230118161110.521504-4-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The platform data definition for ux500 sound devices was removed
six years ago after the DT conversion was completed, see commit
4b483ed0be ("ARM: ux500: cut some platform data").
Remove some leftover bits in the ASoC driver and just assume that
it always gets probed using DT.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230118161110.521504-3-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The "id" comes from the user. Change the type to unsigned to prevent
an array underflow.
Fixes: f4ea22f7aa ("ASoC: SOF: ipc4: Add support for mtrace log extraction")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/Y8laruWOEwOC/dx9@kili
Signed-off-by: Mark Brown <broonie@kernel.org>
The amplifier may provide hardware support for I/V feedback, or
alternatively the firmware may generate an echo reference attached to
the SSP and dailink used for the amplifier.
To avoid any issues with invalid/NULL substreams in the latter case,
always unconditionally set dpcm_capture.
Link: https://github.com/thesofproject/linux/issues/4083
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20230119163459.2235843-5-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The amplifier may provide hardware support for I/V feedback, or
alternatively the firmware may generate an echo reference attached to
the SSP and dailink used for the amplifier.
To avoid any issues with invalid/NULL substreams in the latter case,
always unconditionally set dpcm_capture.
Link: https://github.com/thesofproject/linux/issues/4083
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20230119163459.2235843-4-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The amplifier may provide hardware support for I/V feedback, or
alternatively the firmware may generate an echo reference attached to
the SSP and dailink used for the amplifier.
To avoid any issues with invalid/NULL substreams in the latter case,
always unconditionally set dpcm_capture.
Link: https://github.com/thesofproject/linux/issues/4083
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20230119163459.2235843-3-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The amplifier may provide hardware support for I/V feedback, or
alternatively the firmware may generate an echo reference attached to
the SSP and dailink used for the amplifier.
To avoid any issues with invalid/NULL substreams in the latter case,
always unconditionally set dpcm_capture.
Link: https://github.com/thesofproject/linux/issues/4083
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20230119163459.2235843-2-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Daniel Baluta <daniel.baluta@oss.nxp.com>:
This patch series adds compress API support to ipc_msg_data /
set_stream_data_offset callbacks.
Changes since v1:
- fixed reviewed-by list (+Peter, -Pierre). Since github had
some glitches I added the reviews received manually in the
commits.
- Github PR link: https://github.com/thesofproject/linux/pull/4133
Daniel Baluta (4):
ASoC: SOF: Prepare ipc_msg_data to be used with compress API
ASoC: SOF: Prepare set_stream_data_offset for compress API
ASoC: SOF: Add support for compress API for stream data/offset
ASoC: SOF: compress: Set compress data offset
sound/soc/sof/amd/acp-ipc.c | 8 ++--
sound/soc/sof/amd/acp.h | 5 ++-
sound/soc/sof/compress.c | 9 +++++
sound/soc/sof/intel/hda-ipc.c | 8 ++--
sound/soc/sof/intel/hda.h | 4 +-
sound/soc/sof/ipc3-pcm.c | 3 +-
sound/soc/sof/ipc3.c | 4 +-
sound/soc/sof/mediatek/mt8186/mt8186.c | 2 +-
sound/soc/sof/mediatek/mt8195/mt8195.c | 2 +-
sound/soc/sof/ops.h | 8 ++--
sound/soc/sof/sof-priv.h | 11 ++++--
sound/soc/sof/stream-ipc.c | 53 +++++++++++++++++++-------
12 files changed, 81 insertions(+), 36 deletions(-)
--
2.25.1
Merge series from Peter Ujfalusi <peter.ujfalusi@linux.intel.com>:
This series contains one fix (first patch) followed by a nice to have safety
belts in case we get a widget from topology which is not handled by SOF and will
not have corresponding swidget associated with.
The existing code return when a widget doesn't need to
prepare/unprepare. This will prevent widgets in the sink path from being
prepared/unprepared.
Cc: <stable@vger.kernel.org> # 6.1
Link: https://github.com/thesofproject/linux/issues/4021
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230118101255.29139-4-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Skip preparing/unpreparing widgets if the swidget pointer is NULL. This
will be true in the case of virtual widgets in topology that were added
for reusing the legacy HDA machine driver with SOF.
Fixes: 9862dcf702 ("ASoC: SOF: don't unprepare widget used other pipelines")
Cc: <stable@vger.kernel.org> # 6.1
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230118101255.29139-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We should unprepare the widget if its use_count = 1.
Fixes: 9862dcf702 ("ASoC: SOF: don't unprepare widget used other pipelines")
Cc: <stable@vger.kernel.org> # 6.1
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230118101255.29139-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If there is a connection between a playback stream and a capture stream,
all widgets that are connected to the playback stream and the capture
stream will be in the list.
So, we have to start with the exactly right widget type.
snd_soc_dapm_aif_out is for capture stream and a playback stream should
start with a snd_soc_dapm_aif_in widget.
Contrarily, snd_soc_dapm_dai_in is for playback stream, and a capture
stream should start with a snd_soc_dapm_dai_out widget.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230117123534.2075-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Because now snd_sof_set_stream_data_offset has compress
support we use it to set posn_offset for compress stream.
Reviewed-by: Paul Olaru <paul.olaru@nxp.com>
Reviewed-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20230117122533.201708-5-daniel.baluta@oss.nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_sof_pcm_stream keeps information about both PCM (snd_pcm_substream)
and Compress (snd_compr_stream) streams.
When PCM substream pointer is NULL this means we are dealing with a
compress stream.
Reviewed-by: Paul Olaru <paul.olaru@nxp.com>
Reviewed-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20230117122533.201708-4-daniel.baluta@oss.nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Make second parameter of set_stream_data_offset generic
in order to be used for both PCM and compress streams.
Current patch doesn't introduce any functional change,
just prepare the code for compress support.
Reviewed-by: Paul Olaru <paul.olaru@nxp.com>
Reviewed-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20230117122533.201708-3-daniel.baluta@oss.nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Make second parameter of ipc_msg_data generic
in order to be able to support compressed streams.
This patch doesn't hold any functional change.
With this case we can use ipc_msg_data, to retrieve information from
DSP for both PCM/Compress API.
Reviewed-by: Paul Olaru <paul.olaru@nxp.com>
Reviewed-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20230117122533.201708-2-daniel.baluta@oss.nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for enabling I2S controller on FSD platform.
FSD I2S controller is based on Exynos7 I2S controller, supporting
2CH playback/capture in I2S mode and 7.1CH playback/capture in TDM
mode.
Signed-off-by: Padmanabhan Rajanbabu <p.rajanbabu@samsung.com>
Link: https://lore.kernel.org/r/20230116103823.90757-3-p.rajanbabu@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The shutdown GPIO is active low (SD_N), but this depends on actual board
layout. Linux drivers should only care about logical state, where high
(1) means shutdown and low (0) means do not shutdown.
Invert the GPIO to match logical value while preserving backwards DTB
compatibility. It is not possible to detect whether ACTIVE_HIGH flag in
DTB is because it is an old DTB (using incorrect flag) or it is a new
DTB with a correct hardware pin polarity description. Therefore the
solution prioritizes backwards compatibility while relying on relevant
DTS being upstreamed.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230102114152.297305-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This helps figuring out why the device probe is deferred, e.g. missing
FSL_EDMA driver.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Acked-by: Shengjiu Wang <shengjiu.wang@gmail.com>
Link: https://lore.kernel.org/r/20230111161144.3275546-1-alexander.stein@ew.tq-group.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Initialize is_dsp_mode flag in the beginning of function
fsl_sai_set_dai_fmt_tr().
When the DAIFMT is DAIFMT_DSP_B the first time, is_dsp_mode is
true, then the second time DAIFMT is DAIFMT_I2S, is_dsp_mode
still true, which is a wrong state. So need to initialize
is_dsp_mode flag every time.
Fixes: a3f7dcc9cc ("ASoC: fsl-sai: Add SND_SOC_DAIFMT_DSP_A/B support.")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Link: https://lore.kernel.org/r/1673852874-32200-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add common code to support of_node of codec parsing, so codec phandle
can be assigned by sound-dai in dts.
Signed-off-by: Trevor Wu <trevor.wu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230116034131.23943-12-trevor.wu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add mixer control for irq and memif timing selection.
Signed-off-by: Trevor Wu <trevor.wu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230116034131.23943-10-trevor.wu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add audio clock wrapper and audio tuner control.
Signed-off-by: Trevor Wu <trevor.wu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230116034131.23943-8-trevor.wu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add mt8188 pcmif dai driver support
Signed-off-by: Trevor Wu <trevor.wu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230116034131.23943-7-trevor.wu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add mt8188 etdm dai driver support.
Signed-off-by: Trevor Wu <trevor.wu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230116034131.23943-6-trevor.wu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add mt8188 adda dai driver support.
Signed-off-by: Trevor Wu <trevor.wu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230116034131.23943-5-trevor.wu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add mt8188 audio cg clock control. Audio clock gates are registered to CCF
for reference count and clock parent management.
Signed-off-by: Trevor Wu <trevor.wu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230116034131.23943-4-trevor.wu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add header files for register definition and structure.
Signed-off-by: Trevor Wu <trevor.wu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230116034131.23943-3-trevor.wu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SMC call is required to communicate with ATF for some secure operations,
so we add SMC ops IDs and SMC CMD ID to common header.
Signed-off-by: Trevor Wu <trevor.wu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230116034131.23943-2-trevor.wu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The s3c24xx SoC platform was completely removed, as were most of the
s3c64xx based board files, leaving only the DT based machines as well
as the MACH_WLF_CRAGG_6410 machine. All other board specific ASoC
driver can can now be recycled.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Merge series from Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>:
First patch fixes problems reported when performing shutdown. Second one
is for a problem reported by LKP. Last one fixes problem reported by
checkpatch.
Utilize the helper function instead of casting from ->private_data
or snd_pcm_substream_chip() directly.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230113191410.1454566-1-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Checkpatch script recommends using min_t instead of min with the cast.
Fixes: 69b23b3937 ("ASoC: Intel: avs: Event tracing")
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20230113190310.1451693-4-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
On shutdown reference to i915 driver needs to be released to not spam
logs with unnecessary warnings. While at it do some additional cleanup
to make sure DSP is powered down and interrupts from device are
disabled.
Fixes: 1affc44ea5 ("ASoC: Intel: avs: PCI driver implementation")
Reported-by: Kornel Dulęba <korneld@google.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20230113190310.1451693-2-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When building a PXA kernel without legacy board file support,
the AC97 code is not built, so none of the AC97 drivers
can be used.
Add a Kconfig prompt to let users turn it on, and have it
enabled by default.
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: alsa-devel@alsa-project.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230105134622.254560-15-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Theoretically the device might gone if its reference count drops to 0.
This might be the case when we try to find the first physical node of
the ACPI device. We need to keep reference to it until we get a result
of the above mentioned call. Refactor the code to drop the reference
count at the correct place.
While at it, move to acpi_dev_put() as symmetrical call to the
acpi_dev_get_first_match_dev().
Fixes: a164137ce9 ("ASoC: Intel: add machine driver for SOF+ES8336")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230112112852.67714-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Theoretically the device might gone if its reference count drops to 0.
This might be the case when we try to find the first physical node of
the ACPI device. We need to keep reference to it until we get a result
of the above mentioned call. Refactor the code to drop the reference
count at the correct place.
While at it, move to acpi_dev_put() as symmetrical call to the
acpi_dev_get_first_match_dev().
Fixes: 9a87fc1e06 ("ASoC: Intel: bytcr_wm5102: Add machine driver for BYT/WM5102")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230112112852.67714-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Theoretically the device might gone if its reference count drops to 0.
This might be the case when we try to find the first physical node of
the ACPI device. We need to keep reference to it until we get a result
of the above mentioned call. Refactor the code to drop the reference
count at the correct place.
While at it, move to acpi_dev_put() as symmetrical call to the
acpi_dev_get_first_match_dev().
Fixes: a232b96dce ("ASoC: Intel: bytcr_rt5640: use HID translation util")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230112112852.67714-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Theoretically the device might gone if its reference count drops to 0.
This might be the case when we try to find the first physical node of
the ACPI device. We need to keep reference to it until we get a result
of the above mentioned call. Refactor the code to drop the reference
count at the correct place.
While at it, move to acpi_dev_put() as symmetrical call to the
acpi_dev_get_first_match_dev().
Fixes: 02c0a3b304 ("ASoC: Intel: bytcr_rt5651: add MCLK, quirks and cleanups")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230112112852.67714-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Theoretically the device might gone if its reference count drops to 0.
This might be the case when we try to find the first physical node of
the ACPI device. We need to keep reference to it until we get a result
of the above mentioned call. Refactor the code to drop the reference
count at the correct place.
While at it, move to acpi_dev_put() as symmetrical call to the
acpi_dev_get_first_match_dev().
Fixes: 3c22a73fb8 ("ASoC: Intel: bytcht_es8316: fix HID handling")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230112112852.67714-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Theoretically the device might gone if its reference count drops to 0.
This might be the case when we try to find the first physical node of
the ACPI device. We need to keep reference to it until we get a result
of the above mentioned call. Refactor the code to drop the reference
count at the correct place.
While at it, move to acpi_dev_put() as symmetrical call to the
acpi_dev_get_first_match_dev().
Fixes: 02527c3f23 ("ASoC: amd: add Machine driver for Jadeite platform")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20230112112356.67643-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The dm644x and dm3xx SoCs have been removed, as have the
da850_evm/da830_evm machines, the remaining machines all use the
DT based probing and do not use the vcif driver.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Refactor i2s clock values based on hw_params and use srate and
bclk_ratio variables in clock enable API instead hard-code values.
Signed-off-by: Venkata Prasad Potturu <venkataprasad.potturu@amd.com>
Link: https://lore.kernel.org/r/20230109132104.1259479-4-venkataprasad.potturu@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
when using same cpu dai for 2 different dai links
below error is reported.
error: can't find BE for DAI ACPHS_VIRTUAL1.OUT
To avoid this error add new cpu dai.
Signed-off-by: Venkata Prasad Potturu <venkataprasad.potturu@amd.com>
Link: https://lore.kernel.org/r/20230109132104.1259479-2-venkataprasad.potturu@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A couple of ep93xx board files were unused and got removed, so
the corresponding ASoC support can also be removed.
Cc: Mika Westerberg <mika.westerberg@iki.fi>
Cc: Ryan Mallon <rmallon@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Merge series from Tinghan Shen <tinghan.shen@mediatek.com>:
Add support of MediaTek mt8188 SoC DSP to SOF.
The sof driver patches in this series are taken from
thesofproject/linux/tree/topic/sof-dev-rebase.
The chances are that any error we see here will be EPROBE_DEFER but let's
actually tell the user so they know.
Acked-by: Shengjiu Wang <shengjiu.wang@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230106-asoc-fsl-err-log-v1-1-49d845c99434@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the generic iomem callback for debugfs_add_region_item to support
sof-logger.
Signed-off-by: Tinghan Shen <tinghan.shen@mediatek.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230110084312.12953-4-tinghan.shen@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support of SOF on MediaTek MT8188 SoC.
MT8188 ADSP integrates with a single core Cadence HiFi-5 DSP.
The IPC communication between AP and DSP is based on shared DRAM and
mailbox interrupt.
The change in the mt8186.h is compatible on both mt8186 and
mt8188. The register controls booting the DSP core with the
default address or the user specified address. Both mt8186
and mt8188 should boot with the user specified boot in the driver.
The usage of the register is the same on both SoC, but the
control bit is different on mt8186 and mt8188, which is bit 1 on mt8186
and bit 0 on mt8188. Configure the redundant bit has noside effect
on both SoCs.
Signed-off-by: Tinghan Shen <tinghan.shen@mediatek.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230110084312.12953-3-tinghan.shen@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The fsl-asoc-card AC'97 support currently tries to route to Playback and
Capture widgets provided by the AC'97 CODEC. This doesn't work since the
generic AC'97 driver registers with an "AC97" at the front of the stream
and hence widget names, update to reflect reality. It's not clear to me
if or how this ever worked.
Acked-by: Shengjiu Wang <shengjiu.wang@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230106-asoc-udoo-probe-v1-2-a5d7469d4f67@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The SSI driver calls the AC'97 playback and transmit streams "AC97 Playback"
and "AC97 Capture" respectively. This is the same name used by the generic
AC'97 CODEC driver in ASoC, creating confusion for the Freescale ASoC card
when it attempts to use these widgets in routing. Add a "CPU" in the name
like the regular DAIs registered by the driver to disambiguate.
Acked-by: Shengjiu Wang <shengjiu.wang@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230106-asoc-udoo-probe-v1-1-a5d7469d4f67@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Francesco Dolcini <francesco@dolcini.it>:
Add support for BTL (Bridge Tied Load) configuration to NAU8822 audio codec,
since this requires adding a new property to the binding convert it from
txt to yaml first.
Merge series from Chancel Liu <chancel.liu@nxp.com>:
This patchset supports XCVR on i.MX93 platform.
changes in v2:
- remove unnecessary code which causes kernel test robot reporting error
Chancel Liu (3):
ASoC: dt-bindings: fsl,xcvr: Add compatible string for i.MX93 platform
ASoC: fsl_xcvr: Add support for i.MX93 platform
ASoC: fsl_xcvr: Add constraints of period size while using eDMA
.../devicetree/bindings/sound/fsl,xcvr.yaml | 1 +
sound/soc/fsl/fsl_xcvr.c | 155 ++++++++++++------
sound/soc/fsl/fsl_xcvr.h | 7 +
3 files changed, 115 insertions(+), 48 deletions(-)
--
2.25.1
The Device_ID registers already tell us if a device supports the SDCA
specification or not, in hindsight we never needed a property when the
information is reported by both hardware and ACPI.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20221118025807.534863-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
commit dcc2c012c7 ("ASoC: Fix gpiolib dependencies") removed a
series of unnecessary dependencies on GPIOLIB when the gpio was
optional.
A similar simplification seems valid for nau8315, so remove the
dependency as well. This will avoid the following warning
WARNING: unmet direct dependencies detected for SND_SOC_NAU8315
Depends on [n]: SOUND [=y] && !UML && SND [=y] && SND_SOC [=y] &&
GPIOLIB [=n]
Selected by [y]:
- SND_SOC_INTEL_SOF_NAU8825_MACH [=y] && SOUND [=y] && !UML &&
SND [=y] && SND_SOC [=y] && SND_SOC_INTEL_MACH [=y] &&
(SND_SOC_SOF_HDA_LINK [=y] || SND_SOC_SOF_BAYTRAIL [=n]) &&
I2C [=y] && ACPI [=y] && SND_HDA_CODEC_HDMI [=y] &&
SND_SOC_SOF_HDA_AUDIO_CODEC [=y] && (MFD_INTEL_LPSS [=n] ||
COMPILE_TEST [=y])
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ajye Huang <ajye_huang@compal.corp-partner.google.com>
Link: https://lore.kernel.org/r/20230108114351.539786-1-ajye_huang@compal.corp-partner.google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function primary_codec_init() should return 0 if dmic_sel is null.
Here is the warning message reported by 0-DAY CI Kernel Test Service.
smatch warnings:
primary_codec_init() warn: missing error code? 'ret'
...
2022-11-02 141 if (!priv->dmic_sel) {
2022-11-02 142 dev_info(card->dev, "dmic_sel is null\n");
2022-11-02 @143 return ret;
return -EIVNAL;? return 0;?
2022-11-02 144 }
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Ajye Huang <ajye_huang@compal.corp-partner.google.com>
Link: https://lore.kernel.org/r/20230107175933.12973-1-ajye_huang@compal.corp-partner.google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Clang warns:
sound/soc/amd/ps/pci-ps.c:218:2: error: variable 'ret' is used uninitialized whenever switch default is taken [-Werror,-Wsometimes-uninitialized]
default:
^~~~~~~
sound/soc/amd/ps/pci-ps.c:239:9: note: uninitialized use occurs here
return ret;
^~~
sound/soc/amd/ps/pci-ps.c:190:9: note: initialize the variable 'ret' to silence this warning
int ret;
^
= 0
1 error generated.
ret is used uninitialized if 'goto de_init' is taken. As this is not an
error nor should the ACP be deinitialized, just directly return 0 in
this case statement, which resolves the warning.
Fixes: 1d325cdaf7 ("ASoC: amd: ps: refactor platform device creation logic")
Link: https://github.com/ClangBuiltLinux/linux/issues/1779
Suggested-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Syed Saba Kareem <syed.sabakareem@amd.com>
Link: https://lore.kernel.org/r/20230105-wsometimes-uninitialized-pci-ps-c-v2-1-c50321676325@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
eDMA on i.MX93 platform requires the period size to be multiple of
maxburst.
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Acked-by: Shengjiu Wang <shengjiu.wang@gmail.com>
Link: https://lore.kernel.org/r/20230104023953.2973362-4-chancel.liu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add compatible string and specific soc data to support XCVR on i.MX93
platform. XCVR IP on i.MX93 is cut to SPDIF only by removing external
PHY.
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Acked-by: Shengjiu Wang <shengjiu.wang@gmail.com>
Link: https://lore.kernel.org/r/20230104023953.2973362-3-chancel.liu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow configuring the two loudspeaker outputs as a
single Bridge Tied Load output getting higher output power.
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20230104140412.35575-4-francesco@dolcini.it
Signed-off-by: Mark Brown <broonie@kernel.org>
Older Qualcomm platforms like APQ8016 do not have hardware support for
SoundWire, so kernel configurations made specifically for those platforms
will usually not have CONFIG_SOUNDWIRE enabled.
Unfortunately commit 8d89cf6ff2 ("ASoC: qcom: cleanup and fix
dependency of QCOM_COMMON") breaks those kernel configurations, because
SOUNDWIRE is now a required dependency for SND_SOC_QCOM_COMMON (and in
turn also SND_SOC_APQ8016_SBC). Trying to migrate such a kernel config
silently disables SND_SOC_APQ8016_SBC and breaks audio functionality.
The soundwire helpers in common.c are only used by two of the Qualcomm
audio machine drivers, so building and requiring CONFIG_SOUNDWIRE for
all platforms is unnecessary.
There is no need to stuff all common code into a single module. Fix the
issue by moving the soundwire helpers to a separate SND_SOC_QCOM_SDW
module/option that is selected only by the machine drivers that make
use of them. This also allows reverting the imply/depends changes from
the previous fix because both SM8250 and SC8280XP already depend on
SOUNDWIRE, so the soundwire helpers will be only built if SOUNDWIRE
is really enabled.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Fixes: 8d89cf6ff2 ("ASoC: qcom: cleanup and fix dependency of QCOM_COMMON")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20221231115506.82991-1-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit fc7a6209d5 ("bus: Make remove callback return void")
forces bus_type::remove be void-returned, it doesn't make much sense
for any bus based driver implementing remove callbalk to return
non-void to its caller.
As such, change the remove function for apr bus based drivers to
return void.
Signed-off-by: Dawei Li <set_pte_at@outlook.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/TYCP286MB23232B7968D34DB8323B0F16CAFB9@TYCP286MB2323.JPNP286.PROD.OUTLOOK.COM
The parameter "max" of SOC_SINGLE_SX_TLV() means the number of steps
rather than maximum value. This patch corrects the minimum value to -8
and the number of steps to 15.
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Acked-by: Shengjiu Wang <shengjiu.wang@gmail.com>
Link: https://lore.kernel.org/r/20230104025754.3019235-1-chancel.liu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Sparse warning:
error: symbol 'acp63_fill_platform_dev_info' was not declared. Should
it be static?
Also reduce line lines below 100 characters.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230104145708.25051-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Retrieve acp_lock mutex as platform data and use it for protecting
ACP common registers access in acp pdm driver.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20230104055435.321327-2-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of calling put_device(&adev->dev) where adev is a pointer
to an ACPI device, use specific call, i.e. acpi_dev_put().
Also move it out of the conditional to make it more visible in case
some other code will be added which may use that pointer. We need
to keep a reference as long as we use the pointer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230102203037.16120-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of calling put_device(&adev->dev) where adev is a pointer
to an ACPI device, use specific call, i.e. acpi_dev_put().
Also move it out of the conditional to make it more visible in case
some other code will be added which may use that pointer. We need
to keep a reference as long as we use the pointer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230102203037.16120-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of calling put_device(&adev->dev) where adev is a pointer
to an ACPI device, use specific call, i.e. acpi_dev_put().
Also move it out of the conditional to make it more visible in case
some other code will be added which may use that pointer. We need
to keep a reference as long as we use the pointer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230102203037.16120-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of calling put_device(&adev->dev) where adev is a pointer
to an ACPI device, use specific call, i.e. acpi_dev_put().
Also move it out of the conditional to make it more visible in case
some other code will be added which may use that pointer. We need
to keep a reference as long as we use the pointer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230102203037.16120-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of calling put_device(&adev->dev) where adev is a pointer
to an ACPI device, use specific call, i.e. acpi_dev_put().
Also move it out of the conditional to make it more visible in case
some other code will be added which may use that pointer. We need
to keep a reference as long as we use the pointer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230102203037.16120-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The variable becomes useless since we moved the snd_soc_jack
structure from a static array to sof_hdmi_pcm structure.
Signed-off-by: Brent Lu <brent.lu@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230103073704.722027-1-brent.lu@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
These indices should reference the ID placed within the dai_driver
array, not the indices of the array itself.
This fixes commit 4ff028f6c1 ("ASoC: qcom: lpass-cpu: Make I2S SD
lines configurable"), which among others, broke IPQ8064 audio
(sound/soc/qcom/lpass-ipq806x.c) because it uses ID 4 but we'd stop
initializing the mi2s_playback_sd_mode and mi2s_capture_sd_mode arrays
at ID 0.
Fixes: 4ff028f6c1 ("ASoC: qcom: lpass-cpu: Make I2S SD lines configurable")
Cc: <stable@vger.kernel.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20221231061545.2110253-1-computersforpeace@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from tongjian <tongjian@huaqin.corp-partner.google.com>:
Add MAX98360A for RT5682S, MAX98360A works same as rt1019. So, it can
be supported.
Restore volume after charge pump and PGA activation to ensure
that volume settings are correctly applied when re-enabling codec
from SND_SOC_BIAS_OFF state.
CLASS_W, CHARGE_PUMP and POWER_MANAGEMENT_2 register configuration
affect how the volume register are applied and must be configured first.
Fixes: a91eb199e4 ("ASoC: Initial WM8904 CODEC driver")
Link: https://lore.kernel.org/all/c7864c35-738c-a867-a6a6-ddf9f98df7e7@gmail.com/
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221223080247.7258-1-francesco@dolcini.it
Signed-off-by: Mark Brown <broonie@kernel.org>
RT9120 uses PM runtime autosuspend to decrease the frequently on/off
spent time. This exists one case, when pcm is closed and dev PM is
waiting for autosuspend time expired to enter runtime suspend state.
At the mean time, system is going to enter suspend, dev PM runtime
suspend won't be called. It makes the rt9120 suspend consumption
current not as expected.
This patch can fix the rt9120 dev PM issue during runtime autosuspend
and system suspend by binding dev PM runtime and ASoC component PM.
Fixes: 80b949f332 ("ASoC: rt9120: Use pm_runtime and regcache to optimize 'pwdnn' logic")
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/1672301033-3675-1-git-send-email-u0084500@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
