The data holding the volume label information is zeroed in case no valid
volume label was found. Since the label information isn't used in that
case, zeroing the data doesn't provide any value whatsoever.
Remove the unnecessary memset() call accordingly.
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://lore.kernel.org/r/20230915131001.697070-2-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch removes old code of badblocks_set(), badblocks_clear() and
badblocks_check(), and make them as wrappers to call _badblocks_set(),
_badblocks_clear() and _badblocks_check().
By this change now the badblock handing switch to the improved algorithm
in _badblocks_set(), _badblocks_clear() and _badblocks_check().
This patch only contains the changes of old code deletion, new added
code for the improved algorithms are in previous patches.
Signed-off-by: Coly Li <colyli@suse.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Geliang Tang <geliang.tang@suse.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: NeilBrown <neilb@suse.de>
Cc: Vishal L Verma <vishal.l.verma@intel.com>
Cc: Xiao Ni <xni@redhat.com>
Reviewed-by: Xiao Ni <xni@redhat.com>
Acked-by: Geliang Tang <geliang.tang@suse.com>
Link: https://lore.kernel.org/r/20230811170513.2300-7-colyli@suse.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch rewrites badblocks_check() with similar coding style as
_badblocks_set() and _badblocks_clear(). The only difference is bad
blocks checking may handle multiple ranges in bad tables now.
If a checking range covers multiple bad blocks range in bad block table,
like the following condition (C is the checking range, E1, E2, E3 are
three bad block ranges in bad block table),
+------------------------------------+
| C |
+------------------------------------+
+----+ +----+ +----+
| E1 | | E2 | | E3 |
+----+ +----+ +----+
The improved badblocks_check() algorithm will divide checking range C
into multiple parts, and handle them in 7 runs of a while-loop,
+--+ +----+ +----+ +----+ +----+ +----+ +----+
|C1| | C2 | | C3 | | C4 | | C5 | | C6 | | C7 |
+--+ +----+ +----+ +----+ +----+ +----+ +----+
+----+ +----+ +----+
| E1 | | E2 | | E3 |
+----+ +----+ +----+
And the start LBA and length of range E1 will be set as first_bad and
bad_sectors for the caller.
The return value rule is consistent for multiple ranges. For example if
there are following bad block ranges in bad block table,
Index No. Start Len Ack
0 400 20 1
1 500 50 1
2 650 20 0
the return value, first_bad, bad_sectors by calling badblocks_set() with
different checking range can be the following values,
Checking Start, Len Return Value first_bad bad_sectors
100, 100 0 N/A N/A
100, 310 1 400 10
100, 440 1 400 10
100, 540 1 400 10
100, 600 -1 400 10
100, 800 -1 400 10
In order to make code review easier, this patch names the improved bad
block range checking routine as _badblocks_check() and does not change
existing badblock_check() code yet. Later patch will delete old code of
badblocks_check() and make it as a wrapper to call _badblocks_check().
Then the new added code won't mess up with the old deleted code, it will
be more clear and easier for code review.
Signed-off-by: Coly Li <colyli@suse.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Geliang Tang <geliang.tang@suse.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: NeilBrown <neilb@suse.de>
Cc: Vishal L Verma <vishal.l.verma@intel.com>
Cc: Xiao Ni <xni@redhat.com>
Reviewed-by: Xiao Ni <xni@redhat.com>
Acked-by: Geliang Tang <geliang.tang@suse.com>
Link: https://lore.kernel.org/r/20230811170513.2300-6-colyli@suse.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
With the fundamental ideas and helper routines from badblocks_set()
improvement, clearing bad block for multiple ranges is much simpler.
With a similar idea from badblocks_set() improvement, this patch
simplifies bad block range clearing into 5 situations. No matter how
complicated the clearing condition is, we just look at the head part
of clearing range with relative already set bad block range from the
bad block table. The rested part will be handled in next run of the
while-loop.
Based on existing helpers added from badblocks_set(), this patch adds
two more helpers,
- front_clear()
Clear the bad block range from bad block table which is front
overlapped with the clearing range.
- front_splitting_clear()
Handle the condition that the clearing range hits middle of an
already set bad block range from bad block table.
Similar as badblocks_set(), the first part of clearing range is handled
with relative bad block range which is find by prev_badblocks(). In most
cases a valid hint is provided to prev_badblocks() to avoid unnecessary
bad block table iteration.
This patch also explains the detail algorithm code comments at beginning
of badblocks.c, including which five simplified situations are
categrized and how all the bad block range clearing conditions are
handled by these five situations.
Again, in order to make the code review easier and avoid the code
changes mixed together, this patch does not modify badblock_clear() and
implement another routine called _badblock_clear() for the improvement.
Later patch will delete current code of badblock_clear() and make it as
a wrapper to _badblock_clear(), so the code change can be much clear for
review.
Signed-off-by: Coly Li <colyli@suse.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Geliang Tang <geliang.tang@suse.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: NeilBrown <neilb@suse.de>
Cc: Vishal L Verma <vishal.l.verma@intel.com>
Cc: Xiao Ni <xni@redhat.com>
Reviewed-by: Xiao Ni <xni@redhat.com>
Acked-by: Geliang Tang <geliang.tang@suse.com>
Link: https://lore.kernel.org/r/20230811170513.2300-5-colyli@suse.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Recently I received a bug report that current badblocks code does not
properly handle multiple ranges. For example,
badblocks_set(bb, 32, 1, true);
badblocks_set(bb, 34, 1, true);
badblocks_set(bb, 36, 1, true);
badblocks_set(bb, 32, 12, true);
Then indeed badblocks_show() reports,
32 3
36 1
But the expected bad blocks table should be,
32 12
Obviously only the first 2 ranges are merged and badblocks_set() returns
and ignores the rest setting range.
This behavior is improper, if the caller of badblocks_set() wants to set
a range of blocks into bad blocks table, all of the blocks in the range
should be handled even the previous part encountering failure.
The desired way to set bad blocks range by badblocks_set() is,
- Set as many as blocks in the setting range into bad blocks table.
- Merge the bad blocks ranges and occupy as less as slots in the bad
blocks table.
- Fast.
Indeed the above proposal is complicated, especially with the following
restrictions,
- The setting bad blocks range can be acknowledged or not acknowledged.
- The bad blocks table size is limited.
- Memory allocation should be avoided.
The basic idea of the patch is to categorize all possible bad blocks
range setting combinations into much less simplified and more less
special conditions. Inside badblocks_set() there is an implicit loop
composed by jumping between labels 're_insert' and 'update_sectors'. No
matter how large the setting bad blocks range is, in every loop just a
minimized range from the head is handled by a pre-defined behavior from
one of the categorized conditions. The logic is simple and code flow is
manageable.
The different relative layout between the setting range and existing bad
block range are checked and handled (merge, combine, overwrite, insert)
by the helpers in previous patch. This patch is to make all the helpers
work together with the above idea.
This patch only has the algorithm improvement for badblocks_set(). There
are following patches contain improvement for badblocks_clear() and
badblocks_check(). But the algorithm in badblocks_set() is fundamental
and typical, other improvement in clear and check routines are based on
all the helpers and ideas in this patch.
In order to make the change to be more clear for code review, this patch
does not directly modify existing badblocks_set(), and just add a new
one named _badblocks_set(). Later patch will remove current existing
badblocks_set() code and make it as a wrapper of _badblocks_set(). So
the new added change won't be mixed with deleted code, the code review
can be easier.
Signed-off-by: Coly Li <colyli@suse.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Geliang Tang <geliang.tang@suse.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: NeilBrown <neilb@suse.de>
Cc: Vishal L Verma <vishal.l.verma@intel.com>
Cc: Wols Lists <antlists@youngman.org.uk>
Cc: Xiao Ni <xni@redhat.com>
Reviewed-by: Xiao Ni <xni@redhat.com>
Acked-by: Geliang Tang <geliang.tang@suse.com>
Link: https://lore.kernel.org/r/20230811170513.2300-4-colyli@suse.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch adds several helper routines to improve badblock ranges
handling. These helper routines will be used later in the improved
version of badblocks_set()/badblocks_clear()/badblocks_check().
- Helpers prev_by_hint() and prev_badblocks() are used to find the bad
range from bad table which the searching range starts at or after.
- The following helpers are to decide the relative layout between the
manipulating range and existing bad block range from bad table.
- can_merge_behind()
Return 'true' if the manipulating range can backward merge with the
bad block range.
- can_merge_front()
Return 'true' if the manipulating range can forward merge with the
bad block range.
- can_combine_front()
Return 'true' if two adjacent bad block ranges before the
manipulating range can be merged.
- overlap_front()
Return 'true' if the manipulating range exactly overlaps with the
bad block range in front of its range.
- overlap_behind()
Return 'true' if the manipulating range exactly overlaps with the
bad block range behind its range.
- can_front_overwrite()
Return 'true' if the manipulating range can forward overwrite the
bad block range in front of its range.
- The following helpers are to add the manipulating range into the bad
block table. Different routine is called with the specific relative
layout between the manipulating range and other bad block range in the
bad block table.
- behind_merge()
Merge the manipulating range with the bad block range behind its
range, and return the number of merged length in unit of sector.
- front_merge()
Merge the manipulating range with the bad block range in front of
its range, and return the number of merged length in unit of sector.
- front_combine()
Combine the two adjacent bad block ranges before the manipulating
range into a larger one.
- front_overwrite()
Overwrite partial of whole bad block range which is in front of the
manipulating range. The overwrite may split existing bad block range
and generate more bad block ranges into the bad block table.
- insert_at()
Insert the manipulating range at a specific location in the bad
block table.
All the above helpers are used in later patches to improve the bad block
ranges handling for badblocks_set()/badblocks_clear()/badblocks_check().
Signed-off-by: Coly Li <colyli@suse.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Geliang Tang <geliang.tang@suse.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: NeilBrown <neilb@suse.de>
Cc: Vishal L Verma <vishal.l.verma@intel.com>
Cc: Xiao Ni <xni@redhat.com>
Reviewed-by: Xiao Ni <xni@redhat.com>
Acked-by: Geliang Tang <geliang.tang@suse.com>
Link: https://lore.kernel.org/r/20230811170513.2300-3-colyli@suse.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Now we update driver tags request table in blk_mq_get_driver_tag(),
so the driver that support queue_rqs() have to update that inflight
table by itself.
Move it to blk_mq_start_request(), which is a better place where
we setup the deadline for request timeout check. And it's just
where the request becomes inflight.
Signed-off-by: Chengming Zhou <zhouchengming@bytedance.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230913151616.3164338-5-chengming.zhou@linux.dev
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Since active requests have been accounted when allocate driver tags,
we can remove this limit now.
Signed-off-by: Chengming Zhou <zhouchengming@bytedance.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230913151616.3164338-4-chengming.zhou@linux.dev
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Since the previous patch change to only account active requests when
we really allocate the driver tag, the RQF_MQ_INFLIGHT can be removed
and no double account problem.
1. none elevator: flush request will use the first pending request's
driver tag, won't double account.
2. other elevator: flush request will be accounted when allocate driver
tag when issue, and will be unaccounted when it put the driver tag.
Signed-off-by: Chengming Zhou <zhouchengming@bytedance.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230913151616.3164338-3-chengming.zhou@linux.dev
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There is a limit that batched queue_rqs() can't work on shared tags
queue, since the account of active requests can't be done there.
Now we account the active requests only in blk_mq_get_driver_tag(),
which is not the time we get driver tag actually (with none elevator).
To support batched queue_rqs() on shared tags queue, we move the
account of active requests to where we get the driver tag:
1. none elevator: blk_mq_get_tags() and blk_mq_get_tag()
2. other elevator: __blk_mq_alloc_driver_tag()
This is clearer and match with the unaccount side, which just happen
when we put the driver tag.
The other good point is that we don't need RQF_MQ_INFLIGHT trick
anymore, which used to avoid double account of flush request.
Now we only account when actually get the driver tag, so all is good.
We will remove RQF_MQ_INFLIGHT in the next patch.
Signed-off-by: Chengming Zhou <zhouchengming@bytedance.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230913151616.3164338-2-chengming.zhou@linux.dev
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When nr_hw_queues shrink, we free the excess tags before realloc'ing
hw_ctxs for each queue. During that resize, we may need to access those
tags, like blk_mq_tag_idle(hctx) will access queue shared tags.
This can cause a slab use-after-free, as reported by KASAN. Fix it by
moving the releasing of excess tags to the end.
Fixes: e1dd7bc930 ("blk-mq: fix tags leak when shrink nr_hw_queues")
Reported-by: Yi Zhang <yi.zhang@redhat.com>
Closes: https://lore.kernel.org/all/CAHj4cs_CK63uoDpGBGZ6DN4OCTpzkR3UaVgK=LX8Owr8ej2ieQ@mail.gmail.com/
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Chengming Zhou <zhouchengming@bytedance.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20230908005702.2183908-1-chengming.zhou@linux.dev
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There is no need to unpin the added page when adding it to the bio fails
as that is done by the loop below. Instead we want to unpin it when adding
a single page to the bio more than once as bio_release_pages will only
unpin it once.
Fixes: d1916c86cc ("block: move same page handling from __bio_add_pc_page to the callers")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20230905124731.328255-1-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit a33df75c63 ("block: use an xarray for disk->part_tbl") remove
disk_expand_part_tbl() in add_partition(), which means all kinds of
devices will support extended dynamic `dev_t`.
However, some devices with GENHD_FL_NO_PART are not expected to add or
resize partition.
Fix this by adding check of GENHD_FL_NO_PART before add or resize
partition.
Fixes: a33df75c63 ("block: use an xarray for disk->part_tbl")
Signed-off-by: Li Lingfeng <lilingfeng3@huawei.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20230831075900.1725842-1-lilingfeng@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
file_remove_privs instantly returns 0 when not called for regular files,
so don't bother.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20230831121911.280155-1-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently, 'carryover_ios/bytes' is not handled in throtl_trim_slice(),
for consequence, 'carryover_ios/bytes' will be used to throttle bio
multiple times, for example:
1) set iops limit to 100, and slice start is 0, slice end is 100ms;
2) current time is 0, and 10 ios are dispatched, those io won't be
throttled and io_disp is 10;
3) still at current time 0, update iops limit to 1000, carryover_ios is
updated to (0 - 10) = -10;
4) in this slice(0 - 100ms), io_allowed = 100 + (-10) = 90, which means
only 90 ios can be dispatched without waiting;
5) assume that io is throttled in slice(0 - 100ms), and
throtl_trim_slice() update silce to (100ms - 200ms). In this case,
'carryover_ios/bytes' is not cleared and still only 90 ios can be
dispatched between 100ms - 200ms.
Fix this problem by updating 'carryover_ios/bytes' in
throtl_trim_slice().
Fixes: a880ae93e5 ("blk-throttle: fix io hung due to configuration updates")
Reported-by: zhuxiaohui <zhuxiaohui.400@bytedance.com>
Link: https://lore.kernel.org/all/20230812072116.42321-1-zhuxiaohui.400@bytedance.com/
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/20230816012708.1193747-5-yukuai1@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
carryover_ios/bytes[] can be negative in the case that ios are
dispatched in the slice in advance, and then configuration is updated.
For example:
1) set iops limit to 1000, and slice start is 0, slice end is 100ms;
2) current time is 0, and 100 ios are dispatched, those ios will not be
throttled, hence io_disp is 100;
3) still at current time 0, update iops limit to 100, then carryover_ios
is (0 - 100) = -100;
4) then, dispatch a new io at time 0, the expected result is that this
io will wait for 1s. The calculation in tg_within_iops_limit:
io_disp = 0;
io_allowed = calculate_io_allowed + carryover_ios
= 10 + (-100) = -90;
io won't be throttled if (io_disp + 1 < io_allowed) passed.
Before this patch, in step 4) (io_disp + 1 < io_allowed) is passed,
because -90 for unsigned value is very huge, and such io won't be
throttled.
Fix this problem by checking if 'io/bytes_allowed' is negative first.
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/20230816012708.1193747-3-yukuai1@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
'carryover_bytes/ios' can be negative, indicate that some bio is
dispatched in advance within slice while configuration is updated.
Print a huge value is not user-friendly.
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/20230816012708.1193747-2-yukuai1@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=p1bd
-----END PGP SIGNATURE-----
Merge tag 'for-6.6/block-2023-08-28' of git://git.kernel.dk/linux
Pull block updates from Jens Axboe:
"Pretty quiet round for this release. This contains:
- Add support for zoned storage to ublk (Andreas, Ming)
- Series improving performance for drivers that mark themselves as
needing a blocking context for issue (Bart)
- Cleanup the flush logic (Chengming)
- sed opal keyring support (Greg)
- Fixes and improvements to the integrity support (Jinyoung)
- Add some exports for bcachefs that we can hopefully delete again in
the future (Kent)
- deadline throttling fix (Zhiguo)
- Series allowing building the kernel without buffer_head support
(Christoph)
- Sanitize the bio page adding flow (Christoph)
- Write back cache fixes (Christoph)
- MD updates via Song:
- Fix perf regression for raid0 large sequential writes (Jan)
- Fix split bio iostat for raid0 (David)
- Various raid1 fixes (Heinz, Xueshi)
- raid6test build fixes (WANG)
- Deprecate bitmap file support (Christoph)
- Fix deadlock with md sync thread (Yu)
- Refactor md io accounting (Yu)
- Various non-urgent fixes (Li, Yu, Jack)
- Various fixes and cleanups (Arnd, Azeem, Chengming, Damien, Li,
Ming, Nitesh, Ruan, Tejun, Thomas, Xu)"
* tag 'for-6.6/block-2023-08-28' of git://git.kernel.dk/linux: (113 commits)
block: use strscpy() to instead of strncpy()
block: sed-opal: keyring support for SED keys
block: sed-opal: Implement IOC_OPAL_REVERT_LSP
block: sed-opal: Implement IOC_OPAL_DISCOVERY
blk-mq: prealloc tags when increase tagset nr_hw_queues
blk-mq: delete redundant tagset map update when fallback
blk-mq: fix tags leak when shrink nr_hw_queues
ublk: zoned: support REQ_OP_ZONE_RESET_ALL
md: raid0: account for split bio in iostat accounting
md/raid0: Fix performance regression for large sequential writes
md/raid0: Factor out helper for mapping and submitting a bio
md raid1: allow writebehind to work on any leg device set WriteMostly
md/raid1: hold the barrier until handle_read_error() finishes
md/raid1: free the r1bio before waiting for blocked rdev
md/raid1: call free_r1bio() before allow_barrier() in raid_end_bio_io()
blk-cgroup: Fix NULL deref caused by blkg_policy_data being installed before init
drivers/rnbd: restore sysfs interface to rnbd-client
md/raid5-cache: fix null-ptr-deref for r5l_flush_stripe_to_raid()
raid6: test: only check for Altivec if building on powerpc hosts
raid6: test: make sure all intermediate and artifact files are .gitignored
...
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRAhzRXHqcMeLMyaSiRxhvAZXjcogUCZOXpbgAKCRCRxhvAZXjc
oi8PAQCtXelGZHmTcmevsO8p4Qz7hFpkonZ/TnxKf+RdnlNgPgD+NWi+LoRBpaAj
xk4z8SqJaTTP4WXrG5JZ6o7EQkUL8gE=
=2e9I
-----END PGP SIGNATURE-----
Merge tag 'v6.6-vfs.super' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull superblock updates from Christian Brauner:
"This contains the super rework that was ready for this cycle. The
first part changes the order of how we open block devices and allocate
superblocks, contains various cleanups, simplifications, and a new
mechanism to wait on superblock state changes.
This unblocks work to ultimately limit the number of writers to a
block device. Jan has already scheduled follow-up work that will be
ready for v6.7 and allows us to restrict the number of writers to a
given block device. That series builds on this work right here.
The second part contains filesystem freezing updates.
Overview:
The generic superblock changes are rougly organized as follows
(ignoring additional minor cleanups):
(1) Removal of the bd_super member from struct block_device.
This was a very odd back pointer to struct super_block with
unclear rules. For all relevant places we have other means to get
the same information so just get rid of this.
(2) Simplify rules for superblock cleanup.
Roughly, everything that is allocated during fs_context
initialization and that's stored in fs_context->s_fs_info needs
to be cleaned up by the fs_context->free() implementation before
the superblock allocation function has been called successfully.
After sget_fc() returned fs_context->s_fs_info has been
transferred to sb->s_fs_info at which point sb->kill_sb() if
fully responsible for cleanup. Adhering to these rules means that
cleanup of sb->s_fs_info in fill_super() is to be avoided as it's
brittle and inconsistent.
Cleanup shouldn't be duplicated between sb->put_super() as
sb->put_super() is only called if sb->s_root has been set aka
when the filesystem has been successfully born (SB_BORN). That
complexity should be avoided.
This also means that block devices are to be closed in
sb->kill_sb() instead of sb->put_super(). More details in the
lower section.
(3) Make it possible to lookup or create a superblock before opening
block devices
There's a subtle dependency on (2) as some filesystems did rely
on fill_super() to be called in order to correctly clean up
sb->s_fs_info. All these filesystems have been fixed.
(4) Switch most filesystem to follow the same logic as the generic
mount code now does as outlined in (3).
(5) Use the superblock as the holder of the block device. We can now
easily go back from block device to owning superblock.
(6) Export and extend the generic fs_holder_ops and use them as
holder ops everywhere and remove the filesystem specific holder
ops.
(7) Call from the block layer up into the filesystem layer when the
block device is removed, allowing to shut down the filesystem
without risk of deadlocks.
(8) Get rid of get_super().
We can now easily go back from the block device to owning
superblock and can call up from the block layer into the
filesystem layer when the device is removed. So no need to wade
through all registered superblock to find the owning superblock
anymore"
Link: https://lore.kernel.org/lkml/20230824-prall-intakt-95dbffdee4a0@brauner/
* tag 'v6.6-vfs.super' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs: (47 commits)
super: use higher-level helper for {freeze,thaw}
super: wait until we passed kill super
super: wait for nascent superblocks
super: make locking naming consistent
super: use locking helpers
fs: simplify invalidate_inodes
fs: remove get_super
block: call into the file system for ioctl BLKFLSBUF
block: call into the file system for bdev_mark_dead
block: consolidate __invalidate_device and fsync_bdev
block: drop the "busy inodes on changed media" log message
dasd: also call __invalidate_device when setting the device offline
amiflop: don't call fsync_bdev in FDFMTBEG
floppy: call disk_force_media_change when changing the format
block: simplify the disk_force_media_change interface
nbd: call blk_mark_disk_dead in nbd_clear_sock_ioctl
xfs use fs_holder_ops for the log and RT devices
xfs: drop s_umount over opening the log and RT devices
ext4: use fs_holder_ops for the log device
ext4: drop s_umount over opening the log device
...
* Allow the kernel to initiate a freeze of a filesystem. The kernel
and userspace can both hold a freeze on a filesystem at the same
time; the freeze is not lifted until /both/ holders lift it. This
will enable us to fix a longstanding bug in XFS online fsck.
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQ2qTKExjcn+O1o2YRKO3ySh0YRpgUCZLVnJwAKCRBKO3ySh0YR
pqVIAP9u9CZEJ2Zcc7YpBj1MLUQGr2xBmz8RJEVJbQHKVgYcQwEA9BNb4eH4i2Af
K7Qp0OGNgyzZw37lN23Uf/SDuBK2QgM=
=seMl
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRAhzRXHqcMeLMyaSiRxhvAZXjcogUCZOXo2AAKCRCRxhvAZXjc
ojDfAQDguc2saF8WLeXtn2O0pGOW8vTrhpwiFHNI6hwdzf07/AD+LGBpFEqYKyX5
NHPzdR7YYpJoTsQzR4JFJVZqN9Q1xgU=
=wDq0
-----END PGP SIGNATURE-----
Merge tag 'vfs-6.6-merge-2' of ssh://gitolite.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull filesystem freezing updates from Darrick Wong:
New code for 6.6:
* Allow the kernel to initiate a freeze of a filesystem. The kernel
and userspace can both hold a freeze on a filesystem at the same
time; the freeze is not lifted until /both/ holders lift it. This
will enable us to fix a longstanding bug in XFS online fsck.
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Message-Id: <20230822182604.GB11286@frogsfrogsfrogs>
Signed-off-by: Christian Brauner <brauner@kernel.org>
The implementation of strscpy() is more robust and safer.
That's now the recommended way to copy NUL terminated strings.
Signed-off-by: Xu Panda <xu.panda@zte.com.cn>
Signed-off-by: Yang Yang <yang.yang29@zte.com>
Reviewed-by: Justin Stitt <justinstitt@google.com>
Link: https://lore.kernel.org/r/202212031422587503771@zte.com.cn
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Extend the SED block driver so it can alternatively
obtain a key from a sed-opal kernel keyring. The SED
ioctls will indicate the source of the key, either
directly in the ioctl data or from the keyring.
This allows the use of SED commands in scripts such as
udev scripts so that drives may be automatically unlocked
as they become available.
Signed-off-by: Greg Joyce <gjoyce@linux.vnet.ibm.com>
Reviewed-by: Jonathan Derrick <jonathan.derrick@linux.dev>
Acked-by: Jarkko Sakkinen <jarkko@kernel.org>
Link: https://lore.kernel.org/r/20230721211534.3437070-4-gjoyce@linux.vnet.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This is used in conjunction with IOC_OPAL_REVERT_TPR to return a drive to
Original Factory State without erasing the data. If IOC_OPAL_REVERT_LSP
is called with opal_revert_lsp.options bit OPAL_PRESERVE set prior
to calling IOC_OPAL_REVERT_TPR, the drive global locking range will not
be erased.
Signed-off-by: Greg Joyce <gjoyce@linux.vnet.ibm.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jonathan Derrick <jonathan.derrick@linux.dev>
Acked-by: Jarkko Sakkinen <jarkko@kernel.org>
Link: https://lore.kernel.org/r/20230721211534.3437070-3-gjoyce@linux.vnet.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add IOC_OPAL_DISCOVERY ioctl to return raw discovery data to a SED Opal
application. This allows the application to display drive capabilities
and state.
Signed-off-by: Greg Joyce <gjoyce@linux.vnet.ibm.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jonathan Derrick <jonathan.derrick@linux.dev>
Acked-by: Jarkko Sakkinen <jarkko@kernel.org>
Link: https://lore.kernel.org/r/20230721211534.3437070-2-gjoyce@linux.vnet.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Just like blk_mq_alloc_tag_set(), it's better to prepare all tags before
using to map to queue ctxs in blk_mq_map_swqueue(), which now have to
consider empty set->tags[].
The good point is that we can fallback easily if increasing nr_hw_queues
fail, instead of just mapping to hctx[0] when fail in blk_mq_map_swqueue().
And the fallback path already has tags free & clean handling, so all
is good.
Signed-off-by: Chengming Zhou <zhouchengming@bytedance.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230821095602.70742-3-chengming.zhou@linux.dev
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When we increase nr_hw_queues fail, the fallback path will use
blk_mq_update_queue_map() to clear and update all maps.
Obviously, this line of update of HCTX_TYPE_DEFAULT only is not
needed, so delete it.
Signed-off-by: Chengming Zhou <zhouchengming@bytedance.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230821095602.70742-2-chengming.zhou@linux.dev
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Although we don't need to realloc set->tags[] when shrink nr_hw_queues,
we need to free them. Or these tags will be leaked.
How to reproduce:
1. mount -t configfs configfs /mnt
2. modprobe null_blk nr_devices=0 submit_queues=8
3. mkdir /mnt/nullb/nullb0
4. echo 1 > /mnt/nullb/nullb0/power
5. echo 4 > /mnt/nullb/nullb0/submit_queues
6. rmdir /mnt/nullb/nullb0
In step 4, will alloc 9 tags (8 submit queues and 1 poll queue), then
in step 5, new_nr_hw_queues = 5 (4 submit queues and 1 poll queue).
At last in step 6, only these 5 tags are freed, the other 4 tags leaked.
Signed-off-by: Chengming Zhou <zhouchengming@bytedance.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230821095602.70742-1-chengming.zhou@linux.dev
Signed-off-by: Jens Axboe <axboe@kernel.dk>
BLKFLSBUF is a historic ioctl that is called on a file handle to a
block device and syncs either the file system mounted on that block
device if there is one, or otherwise the just the data on the block
device.
Replace the get_super based syncing with a holder operation to remove
the last usage of get_super, and to also support syncing the file system
if the block device is not the main block device stored in s_dev.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Message-Id: <20230811100828.1897174-16-hch@lst.de>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Combine the newly merged bdev_mark_dead helper with the existing
mark_dead holder operation so that all operations that invalidate
a device that is dead or being removed now go through the holder
ops. This allows file systems to explicitly shutdown either ASAP
(for a surprise removal) or after writing back data (for an orderly
removal), and do so not only for the main device.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Message-Id: <20230811100828.1897174-15-hch@lst.de>
Signed-off-by: Christian Brauner <brauner@kernel.org>
We currently have two interfaces that take a block_devices and the find
a mounted file systems to flush or invaldidate data on it. Both are a
bit problematic because they only work for the "main" block devices
that is used as s_dev for the super_block, and because they don't call
into the file system at all.
Merge the two into a new bdev_mark_dead helper that does both the
syncing and invalidation and which is properly documented. This is
in preparation of merging the functionality into the ->mark_dead
holder operation so that it will work on additional block devices
used by a file systems and give us a single entry point for invalidation
of dead devices or media.
Note that a single standalone fsync_bdev call for an obscure ioctl
remains for now, but that one will also be deal with in a bit.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Message-Id: <20230811100828.1897174-14-hch@lst.de>
Signed-off-by: Christian Brauner <brauner@kernel.org>
This message isn't exactly helpful, and file systems already print way more
useful messages when shut down while active.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Message-Id: <20230811100828.1897174-13-hch@lst.de>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Hard code the events to DISK_EVENT_MEDIA_CHANGE as that is the only
useful use case, and drop the superfluous return value.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Message-Id: <20230811100828.1897174-9-hch@lst.de>
Signed-off-by: Christian Brauner <brauner@kernel.org>
-----BEGIN PGP SIGNATURE-----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=LnzH
-----END PGP SIGNATURE-----
Merge tag 'block-6.5-2023-08-19' of git://git.kernel.dk/linux
Pull block fixes from Jens Axboe:
"Main thing here is the fix for the regression in flush handling which
caused IO hangs/stalls for a few reporters. Hopefully that should all
be sorted out now. Outside of that, just a few minor fixes for issues
that were introduced in this cycle"
* tag 'block-6.5-2023-08-19' of git://git.kernel.dk/linux:
blk-mq: release scheduler resource when request completes
blk-crypto: dynamically allocate fallback profile
blk-cgroup: hold queue_lock when removing blkg->q_node
drivers/rnbd: restore sysfs interface to rnbd-client
Chuck reported [1] an IO hang problem on NFS exports that reside on SATA
devices and bisected to commit 615939a2ae ("blk-mq: defer to the normal
submission path for post-flush requests").
We analysed the IO hang problem, found there are two postflush requests
waiting for each other.
The first postflush request completed the REQ_FSEQ_DATA sequence, so go to
the REQ_FSEQ_POSTFLUSH sequence and added in the flush pending list, but
failed to blk_kick_flush() because of the second postflush request which
is inflight waiting in scheduler queue.
The second postflush waiting in scheduler queue can't be dispatched because
the first postflush hasn't released scheduler resource even though it has
completed by itself.
Fix it by releasing scheduler resource when the first postflush request
completed, so the second postflush can be dispatched and completed, then
make blk_kick_flush() succeed.
While at it, remove the check for e->ops.finish_request, as all
schedulers set that. Reaffirm this requirement by adding a WARN_ON_ONCE()
at scheduler registration time, just like we do for insert_requests and
dispatch_request.
[1] https://lore.kernel.org/all/7A57C7AE-A51A-4254-888B-FE15CA21F9E9@oracle.com/
Link: https://lore.kernel.org/linux-block/20230819031206.2744005-1-chengming.zhou@linux.dev/
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202308172100.8ce4b853-oliver.sang@intel.com
Fixes: 615939a2ae ("blk-mq: defer to the normal submission path for post-flush requests")
Reported-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Chengming Zhou <zhouchengming@bytedance.com>
Tested-by: Chuck Lever <chuck.lever@oracle.com>
Link: https://lore.kernel.org/r/20230813152325.3017343-1-chengming.zhou@linux.dev
[axboe: folded in incremental fix and added tags]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
blk_crypto_profile_init() calls lockdep_register_key(), which warns and
does not register if the provided memory is a static object.
blk-crypto-fallback currently has a static blk_crypto_profile and calls
blk_crypto_profile_init() thereupon, resulting in the warning and
failure to register.
Fortunately it is simple enough to use a dynamically allocated profile
and make lockdep function correctly.
Fixes: 2fb48d88e7 ("blk-crypto: use dynamic lock class for blk_crypto_profile::lock")
Cc: stable@vger.kernel.org
Signed-off-by: Sweet Tea Dorminy <sweettea-kernel@dorminy.me>
Reviewed-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20230817141615.15387-1-sweettea-kernel@dorminy.me
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When blkg is removed from q->blkg_list from blkg_free_workfn(), queue_lock
has to be held, otherwise, all kinds of bugs(list corruption, hard lockup,
..) can be triggered from blkg_destroy_all().
Fixes: f1c006f1c6 ("blk-cgroup: synchronize pd_free_fn() from blkg_free_workfn() and blkcg_deactivate_policy()")
Cc: Yu Kuai <yukuai3@huawei.com>
Cc: xiaoli feng <xifeng@redhat.com>
Cc: Chunyu Hu <chuhu@redhat.com>
Cc: Mike Snitzer <snitzer@kernel.org>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/20230817141751.1128970-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
blk-iocost sometimes causes the following crash:
BUG: kernel NULL pointer dereference, address: 00000000000000e0
...
RIP: 0010:_raw_spin_lock+0x17/0x30
Code: be 01 02 00 00 e8 79 38 39 ff 31 d2 89 d0 5d c3 0f 1f 00 0f 1f 44 00 00 55 48 89 e5 65 ff 05 48 d0 34 7e b9 01 00 00 00 31 c0 <f0> 0f b1 0f 75 02 5d c3 89 c6 e8 ea 04 00 00 5d c3 0f 1f 84 00 00
RSP: 0018:ffffc900023b3d40 EFLAGS: 00010046
RAX: 0000000000000000 RBX: 00000000000000e0 RCX: 0000000000000001
RDX: ffffc900023b3d20 RSI: ffffc900023b3cf0 RDI: 00000000000000e0
RBP: ffffc900023b3d40 R08: ffffc900023b3c10 R09: 0000000000000003
R10: 0000000000000064 R11: 000000000000000a R12: ffff888102337000
R13: fffffffffffffff2 R14: ffff88810af408c8 R15: ffff8881070c3600
FS: 00007faaaf364fc0(0000) GS:ffff88842fdc0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000000000e0 CR3: 00000001097b1000 CR4: 0000000000350ea0
Call Trace:
<TASK>
ioc_weight_write+0x13d/0x410
cgroup_file_write+0x7a/0x130
kernfs_fop_write_iter+0xf5/0x170
vfs_write+0x298/0x370
ksys_write+0x5f/0xb0
__x64_sys_write+0x1b/0x20
do_syscall_64+0x3d/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
This happens because iocg->ioc is NULL. The field is initialized by
ioc_pd_init() and never cleared. The NULL deref is caused by
blkcg_activate_policy() installing blkg_policy_data before initializing it.
blkcg_activate_policy() was doing the following:
1. Allocate pd's for all existing blkg's and install them in blkg->pd[].
2. Initialize all pd's.
3. Online all pd's.
blkcg_activate_policy() only grabs the queue_lock and may release and
re-acquire the lock as allocation may need to sleep. ioc_weight_write()
grabs blkcg->lock and iterates all its blkg's. The two can race and if
ioc_weight_write() runs during #1 or between #1 and #2, it can encounter a
pd which is not initialized yet, leading to crash.
The crash can be reproduced with the following script:
#!/bin/bash
echo +io > /sys/fs/cgroup/cgroup.subtree_control
systemd-run --unit touch-sda --scope dd if=/dev/sda of=/dev/null bs=1M count=1 iflag=direct
echo 100 > /sys/fs/cgroup/system.slice/io.weight
bash -c "echo '8:0 enable=1' > /sys/fs/cgroup/io.cost.qos" &
sleep .2
echo 100 > /sys/fs/cgroup/system.slice/io.weight
with the following patch applied:
> diff --git a/block/blk-cgroup.c b/block/blk-cgroup.c
> index fc49be622e05..38d671d5e10c 100644
> --- a/block/blk-cgroup.c
> +++ b/block/blk-cgroup.c
> @@ -1553,6 +1553,12 @@ int blkcg_activate_policy(struct gendisk *disk, const struct blkcg_policy *pol)
> pd->online = false;
> }
>
> + if (system_state == SYSTEM_RUNNING) {
> + spin_unlock_irq(&q->queue_lock);
> + ssleep(1);
> + spin_lock_irq(&q->queue_lock);
> + }
> +
> /* all allocated, init in the same order */
> if (pol->pd_init_fn)
> list_for_each_entry_reverse(blkg, &q->blkg_list, q_node)
I don't see a reason why all pd's should be allocated, initialized and
onlined together. The only ordering requirement is that parent blkgs to be
initialized and onlined before children, which is guaranteed from the
walking order. Let's fix the bug by allocating, initializing and onlining pd
for each blkg and holding blkcg->lock over initialization and onlining. This
ensures that an installed blkg is always fully initialized and onlined
removing the the race window.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Breno Leitao <leitao@debian.org>
Fixes: 9d179b8654 ("blkcg: Fix multiple bugs in blkcg_activate_policy()")
Link: https://lore.kernel.org/r/ZN0p5_W-Q9mAHBVY@slm.duckdns.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
bio_iov_iter_get_pages() trims the IO based on the block size of the
block device the IO will be issued to.
However, bcachefs is a multi device filesystem; when we're creating the
bio we don't yet know which block device the bio will be submitted to -
we have to handle the alignment checks elsewhere.
Thus this is needed to avoid a null ptr deref.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: linux-block@vger.kernel.org
Link: https://lore.kernel.org/r/20230813182636.2966159-3-kent.overstreet@linux.dev
Signed-off-by: Jens Axboe <axboe@kernel.dk>
- bio_set_pages_dirty(), bio_check_pages_dirty() - dio path
- blk_status_to_str() - error messages
- bio_add_folio() - this should definitely be exported for everyone,
it's the modern version of bio_add_page()
Signed-off-by: Kent Overstreet <kent.overstreet@gmail.com>
Cc: linux-block@vger.kernel.org
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Link: https://lore.kernel.org/r/20230813182636.2966159-2-kent.overstreet@linux.dev
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=+1Vt
-----END PGP SIGNATURE-----
Merge tag 'block-6.5-2023-08-11' of git://git.kernel.dk/linux
Pull block fixes from Jens Axboe:
- NVMe pull request via Keith:
- Fixes for request_queue state (Ming)
- Another uuid quirk (August)
- RCU poll fix for NVMe (Ming)
- Fix for an IO stall with polled IO (me)
- Fix for blk-iocost stats enable/disable accounting (Chengming)
- Regression fix for large pages for zram (Christoph)
* tag 'block-6.5-2023-08-11' of git://git.kernel.dk/linux:
nvme: core: don't hold rcu read lock in nvme_ns_chr_uring_cmd_iopoll
blk-iocost: fix queue stats accounting
block: don't make REQ_POLLED imply REQ_NOWAIT
block: get rid of unused plug->nowait flag
zram: take device and not only bvec offset into account
nvme-pci: add NVME_QUIRK_BOGUS_NID for Samsung PM9B1 256G and 512G
nvme-rdma: fix potential unbalanced freeze & unfreeze
nvme-tcp: fix potential unbalanced freeze & unfreeze
nvme: fix possible hang when removing a controller during error recovery
A previous commit added a lockdep annotation, but botched it. Use the
right type.
Fixes: 4eb44d1076 ("block: remove init_mutex and open-code blk_iolatency_try_init")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit a13696b83d ("blk-iolatency: Make initialization lazy") adds
a mutex named "init_mutex" in blk_iolatency_try_init for the race
condition of initializing RQ_QOS_LATENCY.
Now a new lock has been add to struct request_queue by commit a13bd91be2
("block/rq_qos: protect rq_qos apis with a new lock"). And it has been
held in blkg_conf_open_bdev before calling blk_iolatency_init.
So it's not necessary to keep init_mutex in blk_iolatency_try_init, just
remove it.
Since init_mutex has been removed, blk_iolatency_try_init can be
open-coded back to iolatency_set_limit() like ioc_qos_write().
Signed-off-by: Li Lingfeng <lilingfeng3@huawei.com>
Reviewed-by: Michal Koutný <mkoutny@suse.com>
Link: https://lore.kernel.org/r/20230810035111.2236335-1-lilingfeng@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In general, the bvec data structure consists of one for physically
continuous pages. But, in the bvec configuration for bip, physically
continuous integrity pages are composed of each bvec.
Allow bio_integrity_add_page() to create multi-page bvecs, just like
the bio payloads. This simplifies adding larger payloads, and fixes
support for non-tiny workloads with nvme, which stopped using
scatterlist for metadata a while ago.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Fixes: 783b94bd92 ("nvme-pci: do not build a scatterlist to map metadata")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jinyoung Choi <j-young.choi@samsung.com>
Tested-by: "Martin K. Petersen" <martin.petersen@oracle.com>
Reviewed-by: "Martin K. Petersen" <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20230803025202epcms2p82f57cbfe32195da38c776377b55aed59@epcms2p8
Signed-off-by: Jens Axboe <axboe@kernel.dk>
bio_integrity_add_page() returns the add length if successful, else 0,
just as bio_add_page. Simply check return value checking in
bio_integrity_prep to not deal with a > 0 but < len case that can't
happen.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jinyoung Choi <j-young.choi@samsung.com>
Tested-by: "Martin K. Petersen" <martin.petersen@oracle.com>
Reviewed-by: "Martin K. Petersen" <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20230803025058epcms2p5a4d0db5da2ad967668932d463661c633@epcms2p5
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Previously, the bip's bi_size has been set before an integrity pages
were added. If a problem occurs in the process of adding pages for
bip, the bi_size mismatch problem must be dealt with.
When the page is successfully added to bvec, the bi_size is updated.
The parts affected by the change were also contained in this commit.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jinyoung Choi <j-young.choi@samsung.com>
Tested-by: "Martin K. Petersen" <martin.petersen@oracle.com>
Reviewed-by: "Martin K. Petersen" <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20230803024956epcms2p38186a17392706650c582d38ef3dbcd32@epcms2p3
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This will be used for multi-page configuration for integrity payload.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jinyoung Choi <j-young.choi@samsung.com>
Tested-by: "Martin K. Petersen" <martin.petersen@oracle.com>
Reviewed-by: "Martin K. Petersen" <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20230803024827epcms2p838d9e9131492c86a159fff25d195658f@epcms2p8
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The q->stats->accounting is not only used by iocost, but iocost only
increase this counter, never decrease it. So queue stats accounting
will always enabled after using iocost once.
Signed-off-by: Chengming Zhou <zhouchengming@bytedance.com>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/20230804070609.31623-1-chengming.zhou@linux.dev
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Normally these two flags do go together, as the issuer of polled IO
generally cannot wait for resources that will get freed as part of IO
completion. This is because that very task is the one that will complete
the request and free those resources, hence that would introduce a
deadlock.
But it is possible to have someone else issue the polled IO, eg via
io_uring if the request is punted to io-wq. For that case, it's fine to
have the task block on IO submission, as it is not the same task that
will be completing the IO.
It's completely up to the caller to ask for both polled and nowait IO
separately! If we don't allow polled IO where IOCB_NOWAIT isn't set in
the kiocb, then we can run into repeated -EAGAIN submissions and not
make any progress.
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
