The cnic module is responsible for initializing various bnx2x structs
via callbacks provided by the bnx2x module.
One such struct is the queue object for the FCoE queue.
If a device is working in AFEX mode and its configuration allows FCoE yet
the cnic module is not loaded, it's very likely a null pointer dereference
will occur, as the bnx2x will erroneously access the FCoE's queue object.
Prevent said access until cnic properly registers itself.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While the bonding module is unloading, it is considered that after
rtnl_link_unregister all bond devices are destroyed but since no
synchronization mechanism exists, a new bond device can be created
via bonding_masters before unregister_pernet_subsys which would
lead to multiple problems (e.g. NULL pointer dereference, wrong RIP,
list corruption).
This patch fixes the issue by removing any bond devices left in the
netns after bonding_masters is removed from sysfs.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 4de79c737b.
This patch introduces a new bug which causes access to freed memory.
In bond_uninit: list_del(&bond->bond_list);
bond_list is linked in bond_net's dev_list which is freed by
unregister_pernet_subsys.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems that the reason why the dev features were ignored was because
they were enabled after registeration.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases, the VM_PKT_COMP message can arrive later than RNDIS completion
message, which will free the packet memory. This may cause panic due to access
to freed memory in netvsc_send_completion().
This patch fixes this problem by removing rndis_filter_send_request_completion()
from the code path. The function was a no-op.
Reported-by: Long Li <longli@microsoft.com>
Tested-by: Long Li <longli@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The warning about local_bh_enable inside IRQ happens when disconnecting a
virtual NIC.
The reason for the warning is -- netif_tx_disable() is called when the NIC
is disconnected. And it's called within irq context. netif_tx_disable() calls
local_bh_enable() which displays warning if in irq.
The fix is to remove the unnecessary netif_tx_disable & wake_queue() in the
netvsc_linkstatus_callback().
Reported-by: Richard Genoud <richard.genoud@gmail.com>
Tested-by: Long Li <longli@microsoft.com>
Tested-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check KR2 recovery time at the beginning of the work-around function.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ixgbe_notify_dca cannot be called before driver registration
because it expects driver's klist_devices to be allocated and
initialized. While on it make sure debugfs files are removed
when registration fails.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jakub Kicinski <jakub.kicinski@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have a race condition if we try to rmmod bonding and simultaneously add
a bond master through sysfs. In bonding_exit() we first remove the devices
(through rtnl_link_unregister() ) and only after that we remove the sysfs.
If we manage to add a device through sysfs after that the devices were
removed - we'll end up with that device/sysfs structure and with the module
unloaded.
Fix this by first removing the sysfs and only after that calling
rtnl_link_unregister().
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The limit of 0x3c00 is taken from the windows driver.
Suggested-by: Huang, Xiong <xiong@qca.qualcomm.com>
Cc: Huang, Xiong <xiong@qca.qualcomm.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It would cause no link after suspending or shutdowning when the
nic changes the speed to 10M and connects to a link partner which
forces the speed to 100M.
Check the link partner ability to determine which speed to set.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
Here are some more fixes intended for the 3.9 stream...
Regarding the mac80211 bits, Johannes says:
"I had changed the idle handling to simplify it, but broken the
sequencing of commands, at least for ath9k-htc, one patch restores the
sequence. The other patch fixes a crash Jouni found while stress-testing
the remain-on-channel code, when an item is deleted the work struct can
run twice and crash the second time."
As for the iwlwifi bits, Johannes says:
"The only fix here is to the passive-no-RX firmware regulatory
enforcement driver support code to not drop auth frames in quick
succession, leading to not being able to connect to APs on passive
channels in certain circumstances."
Don't forget the NFC bits, about which Samuel says:
"This time we have:
- A crash fix for when a DGRAM LLCP socket is listening while the NFC adapter
is physically removed.
- A potential double skb free when the LLCP socket receive queue is full.
- A fix for properly handling multiple and consecutive LLCP connections, and
not trash the socket ack log.
- A build failure for the MEI microread physical layer, now that the MEI bus
APIs have been merged into char-misc-next."
On top of that, Stone Piao provides an mwifiex fix to avoid accessing
beyond the end of a buffer.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The rt2800pci driver supports the built-in wireless
MAC of the Ralink RT3x5x SoCs. However building the
driver for these SoCs leads to the following error:
LD init/built-in.o
drivers/built-in.o: In function `rt2800pci_rxdone_tasklet':
<...>/drivers/net/wireless/rt2x00/rt2800pci.c:1012: undefined reference to `rt2x00pci_rxdone'
drivers/built-in.o:(.rodata+0x4780): undefined reference to `rt2x00pci_initialize'
drivers/built-in.o:(.rodata+0x4784): undefined reference to `rt2x00pci_uninitialize'
drivers/built-in.o:(.rodata+0x47bc): undefined reference to `rt2x00pci_flush_queue'
drivers/built-in.o:(.rodata+0x4818): undefined reference to `rt2x00pci_regbusy_read'
make[5]: *** [vmlinux] Error 1
The missing functions are provided by the rt2x00pci
module. This module is only selected by the rt2800pci
driver if PCI support is enabled in the kernel, because
some parts of the rt2x00pci code depends on PCI support.
PCI support is not available on the RT3x5x SoCs because
those have no PCI host controller at all.
Move the non PCI specific code from rt2x00pci into a
separate module. This makes it possible to use that
code even if PCI support is disabled. The affected
functions are used by all of the rt2x00 PCI drivers
so select the new module for those drivers.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BugLink: http://bugs.launchpad.net/bugs/1128840
It appears that when this register read fails it never recovers, so
I think there is no need to repeat the same error message ad infinitum.
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Cc: users@rt2x00.serialmonkey.com
Cc: netdev@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath_complete_reset will not be called if ath9k_hw_reset
is unsuccessful, so we need to re-enable intertupts to
balence the previous ath_prepare_reset call. Also schedule a
reset as a best effort method to recover the chip from
whatever state caused the channel change failure.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=55771
Signed-off-by: Robert Shade <robert.shade@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nvram contains critical initialization parameter for firmware to run. Host
driver should not proceed if nvram fails to be downloaded to dongle.
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When multiple cipher suites have been programmed then the lowest
suite is to be retured. This fixes issue when AP mode is using
CCMP and TKIP WPA combination where rekeying will fail.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
on stop_ap the dongle was not properly shutdown. As a result it was
not possible to restart AP or STA after AP operation without
restarting the device. This patch will fix that.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
tx and rx michael tkip keys are always swapped in case being
configured per mac. This is wrong for AP. The swap should only
be done for STA mode.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We are waiting on first scan command of internal scan request
before association, so we should complete on last internal scan
command response.
Cc: <stable@vger.kernel.org> # 3.8
Tested-by: Daniel Drake <dsd@laptop.org>
Tested-by: Marco Cesarano <marco@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 6bbb6d9 "net/mlx4_en: Optimize Rx fast path filter checks" introduced a regression
under which the MAC address read from the card was not converted correctly
(the most significant byte was not handled), fix that.
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that netdev_rx_handler_unregister contains synchronize_net(), we need
to call it outside of bond->lock, cause it might sleep. Also, remove the
already unneded synchronize_net().
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Limit the channel number in scan request, or the driver scan
config structure memory will be overflowed.
Cc: <stable@vger.kernel.org> # 3.5+
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix bug for DM9000 revision B which contain a DSP PHY
DM9000B use DSP PHY instead previouse DM9000 revisions' analog PHY,
So need extra change in initialization, For
explicity PHY Reset and PHY init parameter, and
first DM9000_NCR reset need NCR_MAC_LBK bit by dm9000_probe().
Following DM9000_NCR reset cause by dm9000_open() clear the
NCR_MAC_LBK bit.
Without this fix, Power-up FIFO pointers error happen around 2%
rate among Davicom's customers' boards. With this fix, All above
cases can be solved.
Signed-off-by: Joseph CHANG <josright123@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'link' field of 'struct sh_eth_private' has type 'enum phy_state' while the
'link' field of 'struct phy_device' is merely *int* (having values 0 and 1) and
the former field gets assigned from the latter. Make the field match, getting
rid of incorrectly used PHY_DOWN value in assignments/comparisons.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At least on Renesas R8A7778, EESR.ECI interrupt seems to fire regardless of its
mask in EESIPR register. I can 100% reproduce it with the following scenario:
target is booted with 'ip=on' option, and so IP-Config opens SoC Ether device
but doesn't get a proper reply and then succeeds with on-board SMC chip; then
I login and try to bring up the SoC Ether device with 'ifconfig', and I get
an ECI interrupt once request_irq() is called by sh_eth_open() (while interrupt
mask in EESIPR register is all 0), if that interrupt is accompanied by a pending
EESR.FRC (frame receive completion) interrupt, I get kernel oops in sh_eth_rx()
because sh_eth_ring_init() hasn't been called yet!
The solution I worked out is the following: in sh_eth_interrupt(), mask the
interrupt status from EESR register with the interrupt mask from EESIPR register
in order not to handle the disabled interrupts -- but forcing EESIPR.M_ECI bit
in this mask set because we always need to fully handle EESR.ECI interrupt in
sh_eth_error() in order to quench it (as it doesn't get cleared by just writing
1 to the this bit as all the other interrupts).
While at it, remove unneeded initializer for 'intr_status' variable and give it
*unsigned long* type, matching the type of sh_eth_read()'s result; fix comment.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Max Filippov <max.filippov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code handling the absent LINK signal (or the absent PSR register -- which
reflects the state of this signal) is quite naive and has probably never really
worked. It's probably enough to say that this code is executed only on the LINK
change interrupt (sic!) but even if we actually have the signal and choose to
ignore it (it might be connected to PHY's link/activity LED output as on the
Renesas BOCK-W board), sh_eth_adjust_link() on which this code relies to update
'mdp->link' gets executed later than the LINK change interrupt where it is
checked, and so RX/TX never get enabled via ECMR register.
So, ignore the LINK changed interrupt iff LINK signal is absent (or just chosen
not to be used) or PSR register is absent, and enable/disable RX/TX directly in
sh_eth_adjust_link() in this case.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the Datasheet (page 52):
15-12 Reserved
11-0 RXBC Receive Byte Count
This field indicates the present received frame byte size.
The code has a bug:
rxh = ks8851_rdreg32(ks, KS_RXFHSR);
rxstat = rxh & 0xffff;
rxlen = rxh >> 16; // BUG!!! 0xFFF mask should be applied
Signed-off-by: Max Nekludov <Max.Nekludov@us.elster.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Usage of pci-msi results in corrupted dma packet transfers to the host.
Reported-by: rebelyouth <rebelyouth.hacklab@gmail.com>
Cc: Huang, Xiong <xiong@qca.qualcomm.com>
Tested-by: Christian Sünkenberg <christian.suenkenberg@student.kit.edu>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
WOL is broken because the magic packet status bit is getting set rather
than the enable bit. The PMT interrupt is not getting serviced because
the PMT interrupt is also enabled on the global interrupt, but not
cleared by the global interrupt and the global interrupt is higher
priority. This fixes both of these issues to get WOL working.
There's still a problem with receive after resume, but at least now we
can wake-up.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If skb allocation for the rx ring fails repeatedly, we can reach a point
were the ring is empty. In this condition, the driver is out of sync with
the h/w. While this has always been possible, the removal of the skb
recycling seems to have made triggering this problem easier.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables RX of jumbo frames for LAN7500.
Previously the driver would transmit jumbo frames succesfully but
would drop received jumbo frames (incrementing the interface errors
count).
With this patch applied the device can succesfully receive jumbo
frames up to MTU 9000 (9014 bytes on the wire including ethernet
header).
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently if either arp_interval or miimon is disabled, they both get
disabled, and upon disabling they get executed once more which is not
the proper behaviour. Also when doing a no-op and disabling an already
disabled one, the other again gets disabled.
Also fix the error messages with the proper valid ranges, and a small
typo fix in the up delay error message (outputting "down delay", instead
of "up delay").
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sky2 driver sets the Rx Upper Threshold for Pause Packet generation to a
wrong value which leads to only 2kB of RAM remaining space. This can lead to
Rx overflow errors even with activated flow-control.
Fix: We should increase the value to 8192/8
Signed-off-by: Mirko Lindner <mlindner@marvell.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sky2 driver doesn't count the Receive Overflows because the MAC
interrupt for this event is not set in the MAC's interrupt mask.
The MAC's interrupt mask is set only for Transmit FIFO Underruns.
Fix: The correct setting should be (GM_IS_TX_FF_UR | GM_IS_RX_FF_OR)
Otherwise the Receive Overflow event will not generate any interrupt.
The Receive Overflow interrupt is handled correctly
Signed-off-by: Mirko Lindner <mlindner@marvell.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Romosan reported that since the mac80211 changes in
"mac80211: start auth/assoc timeout on frame status" and
the subsequent fixes in "mac80211: fix auth/assoc timeout
handling" (commits 1672c0e319 and 89afe614c0) there's
sometimes an issue connecting to a 5 GHz network with the
iwlwifi DVM driver.
The reason appears to be that since these commits any bad
TX status makes mac80211 immediately try again, causing
all of the authentication attempts to be quickly rejected
by the firmware as it hasn't heard a beacon yet. Before,
it would wait for the timeout regardless of status.
To fix this, invoke the passive-no-RX workaround when not
associated yet as well. This will cause the first frame
to get lost, but then the driver will stop the queues and
the second attempt will only be transmitted after hearing
a beacon, thus delaying it appropriately to not make the
firmware reject it again.
Reported-by: Alex Romosan <romosan@sycorax.lbl.gov>
Tested-by: Alex Romosan <romosan@sycorax.lbl.gov>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Marc Kleine-Budde says:
====================
here's a patch series for net for the v3.9 release cycle. Fengguang Wu found
two problems with the sja1000 drivers:
A macro in the SH architecture collides with one in the sja1000 driver. I
created a minimal patch suited for stable, only changing this particular
define. (Once net is merged back to net-next, I'll post a patch to uniformly
use a SJA1000_ prefix for the sja100 private defines.) If you prefer, I can
squash both patches together.
Fengguang further noticed that the peak pcmcia driver will not compile on archs
without ioport support. I created a patch to limit the driver to archs which
select HAS_IOPORT in Kconfig.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
This series contains updates to e1000, ixgb and e1000e for Christoph.
Christoph provides 3 patches to resolve missing dma_error_call's to
provided Intel drivers which did not have this fix.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 184b89044f ("tg3: Use VPD fw version
when present") introduced VPD parsing that contained a potential length
overflow.
Limit the hardware's reported firmware string length (max 255 bytes) to
stay inside the driver's firmware string length (32 bytes). On overflow,
truncate the formatted firmware string instead of potentially overwriting
portions of the tg3 struct.
http://cansecwest.com/slides/2013/PrivateCore%20CSW%202013.pdf
Signed-off-by: Kees Cook <keescook@chromium.org>
Reported-by: Oded Horovitz <oded@privatecore.com>
Reported-by: Brad Spengler <spender@grsecurity.net>
Cc: stable@vger.kernel.org
Cc: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To restart tx queue use netif_wake_queue() intead of netif_start_queue()
so that net schedule will restart transmission immediately which will
increase network performance while doing huge data transfers.
Reported-by: Dan Franke <dan.franke@schneider-electric.com>
Suggested-by: Sriramakrishnan A G <srk@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To restart tx queue use netif_wake_queue() intead of netif_start_queue()
so that net schedule will restart transmission immediately which will
increase network performance while doing huge data transfers.
Reported-by: Dan Franke <dan.franke@schneider-electric.com>
Suggested-by: Sriramakrishnan A G <srk@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this patch
1. boot with nfs (no_console_suspend)
2. echo mem >/sys/power/state
3. wakeup by wakesource
4. print "eth0: tx queue full"
This fix above problem by reinit bd queue at restart function
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When calculating "offset" for final RSSI calibration we're using numbers
bigger than s8 can hold. We have for example:
offset[j] = 232 - poll_results[j];
formula. If poll_results[j] is small enough (it usually is) we treat
number's bit as a sign bit. For example 232 - 1 becomes:
0xE8 - 0x1 = 0xE7, which is not 231 but -25.
This code was introduced in e0c9a0219a
and caused stability regression on some cards, for ex. BCM4322.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
il4965_rs_initialize_lq checks to see if sta is null, however, before that
check il4965_rs_use_green dereferences sta when intializing use_green.
Avoid a potential null pointer dereference error by only calling
il4965_rs_use_green after we are sure sta is not null.
Smatch analysis:
drivers/net/wireless/iwlegacy/4965-rs.c:2160 il4965_rs_initialize_lq() warn:
variable dereferenced before check 'sta' (see line 2155)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The following issue was reported.
WARNING: at net/mac80211/util.c:599 ieee80211_can_queue_work.isra.7+0x32/0x40 [mac80211]()
Hardware name: iMac12,1
queueing ieee80211 work while going to suspend
Pid: 0, comm: swapper/0 Tainted: PF O 3.8.2-206.fc18.x86_64 #1
Call Trace: Mar 16 09:39:17 Parags-iMac kernel: [ 3993.642992] <IRQ>
[<ffffffff8105e61f>] warn_slowpath_common+0x7f/0xc0
[<ffffffffa0581420>] ? ath_start_rx_poll+0x70/0x70 [ath9k]
<ffffffff8105e716>] warn_slowpath_fmt+0x46/0x50
[<ffffffffa045b542>] ieee80211_can_queue_work.isra.7+0x32/0x40
Fix this by avoiding to queue the work if our device has
already been marked as suspended or stopped.
Reported-by: Parag Warudkar <parag.lkml@gmail.com>
Tested-by: Parag Warudkar <parag.lkml@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
