Modernize the krait-cc driver to parent-data API and refactor to drop
any use of parent_names. From Documentation all the required clocks should
be declared in DTS so fw_name can be correctly used to get the parents
for all the muxes. .name is also declared to save compatibility with old
DT.
While at it also drop some hardcoded index and introduce an enum to make
index values more clear.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221109005631.3189-5-ansuelsmth@gmail.com
Some bootloader may leave the system in an even more undefined state
with the secondary mux of L2 or other cores sourcing out of the acpu_aux
parent. This results in the clk set to the PXO rate or a PLL8 rate.
The current logic to reset the mux and set them to a defined state only
handle if the mux are configured to source out of QSB. Change this and
force a new and defined state if the current clk is lower than the aux
rate. This way we can handle any wrong configuration where the mux is
sourcing out of QSB (rate 225MHz, currently set to a virtual rate of 1),
PXO rate (rate 25MHz) or PLL8 (needs to be configured to run at 384Mhz).
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221109005631.3189-3-ansuelsmth@gmail.com
clk-krait ignore any rate change if clk is not flagged as enabled.
Correctly enable the secondary mux and div clk to correctly change rate
instead of silently ignoring the request.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221109005631.3189-2-ansuelsmth@gmail.com
The secondary mux parent order is swapped.
This currently doesn't cause problems as the secondary mux is used for idle
clk and as a safe clk source while reprogramming the hfpll.
Each mux have 2 or more output but he always have a safe source to
switch while reprogramming the connected pll. We use a clk notifier to
switch to the correct parent before clk core can apply the correct rate.
The parent to switch is hardcoded in the mux struct.
For the secondary mux the safe source to use is the qsb parent as it's
the only fixed clk as the acpus_aux is a pll that can source from pxo or
from pll8.
The hardcoded safe parent for the secondary mux is set to index 0 that
in the secondary mux map is set to 2.
But the index 0 is actually acpu_aux in the parent list.
Fix the swapped parents to correctly handle idle frequency and output a
sane clk_summary report.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221109005631.3189-1-ansuelsmth@gmail.com
Use devm variant for clk notifier register and correctly handle free
resource on driver remove.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221108215827.30475-1-ansuelsmth@gmail.com
Add apq/ipq8064 errata workaround where the sec_src clock gating needs to
be disabled during switching. krait-cc compatible is not enough to
handle this and limit this workaround to apq/ipq8064. We check machine
compatible to handle this.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220430054458.31321-4-ansuelsmth@gmail.com
When the Hfplls are reprogrammed during the rate change,
the primary muxes which are sourced from the same hfpll
for higher frequencies, needs to be switched to the 'safe
secondary mux' as the parent for that small window. This
is done by registering a clk notifier for the muxes and
switching to the safe parent in the PRE_RATE_CHANGE notifier
and back to the original parent in the POST_RATE_CHANGE notifier.
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Tested-by: Craig Tatlor <ctatlor97@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The Krait CPU clocks are made up of a primary mux and secondary
mux for each CPU and the L2, controlled via cp15 accessors. For
Kraits within KPSSv1 each secondary mux accepts a different aux
source, but on KPSSv2 each secondary mux accepts the same aux
source.
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Tested-by: Craig Tatlor <ctatlor97@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
