The hardware may change this underneath us.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Now that we use regmap to do read-modify-write ops everywhere, we can
rely on the regmap lock and no longer need our own lock.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Use regmap_update_bits in axp288_charger_set_vbus_inlmt, instead of DIY
code.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
While we are doing cleanups, also remove some double blank lines.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The extcon code is the only one to trigger our worker (outside of the
initial run) and we can rely on it to only call us if things have
changed, so there is no need to track the charger-enabled state.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Add missing (terminating) "\n"-s to some dev_dbg messages.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Before this commit we were relying solely on the extcon interface for
cable detection, including to determine if a cable providing vbus is
connected at all. This caused us to turn off charging at boot, because
when we run the initial state processing the axp288-extcon driver is still
running charger-type detection most of the time, so all charger cable
types read as disconnected when we run the initial state processing.
This commit reworks the axp288_charger_extcon_evt_worker flow to use the
VBUS_VALID bit from the PWR_INPUT_STATUS register to determine if we
should turn charging on/off. Note this is the same bit as we use for the
online property.
If VBUS_VALID is set, but the extcon code has not completed the charger
type detection yet, we now simply bail leaving things as configured by
the BIOS (we will get a notifier call when the extcon code is done and
reschedule the axp288_charger_extcon_evt_worker).
The extcon code is the only one to trigger the worker (outside of the
initial run) and we can rely on it to only call us if things have changed,
so while we are completely refactoring axp288_charger_extcon_evt_worker,
also remove the code to check if the state has changed.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
On some devices with an axp288 pmic setting vbus path based on the
id-pin is handled by an ACPI _AIE interrupt on the gpio and the
INT3496 device is disabled.
Instead of returning -EPROBE_DEFER on these devices waiting for the
never to show up INT3496 device, check for its presence and only
request and monitor the matching extcon if the device is there,
otherwise let the firmware handle the vbus path control.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Prior to this commit the code was using 1 notifier_block for all
types of charger cable, this is incorrect as the notifier_block
becomes part of a linked-list and now the same notifier_block
is part of 3 linked lists.
This commit fixes this by using a separate nb per extcon cable.
Note this happened to work fine sofar because axp288_charger was the only
listener, so when added to each of the 3 notifier chains, the next pointer
in the nb would be set to 0, so we've 3 heads pointing to the same nb,
with its next pointing to NULL. But as soon as we mix in a second extcon
consumer things will go boom.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add a MODULE_DEVICE_TABLE to fix the module not auto-loading.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Setting the irq_enable bits is taken care of by the irq chip when we
request the irqs and the driver should not be meddling with the
irq?_en registers itself.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
To set a bit to 1 one needs to pass the mask for the bit to set
as second argument into regmap_update_bits, not "1".
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Do not wait for an extcon notification before processing the cable
states, instead queue the otg / cable work on probe to make sure we
immediately process the initial hardware state.
Note this also requiree moving the getting of the USB_HOST cable state
from the extcon notifier to the workqueue function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Remove info->health, info->present and info->online caching, as no code
is reading the cached values.
Remove if (changed) check before calling power_supply_changed(), we
return early from axp288_charger_extcon_evt_worker if nothing has
changed, so the check is not needed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Deal with the charger type changing without a vbus-disconnect being
reported in between the 2 charger type states:
-Do not return from axp288_charger_extcon_evt_worker early in this case
(track old_chg_type)
-Make calling axp288_charger_enable_charger with the same value as before
a nop, to avoid the need for the caller to check this
-Do no do a dev_err when axp288_charger_enable_charger returns an error,
axp288_charger_enable_charger already returns an error itself
-Disable the charger before changing the charge-current setting (nop if
vbus was seen as disconnected before the change)
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Nothing was setting info->otg.cable, so the extcon_get_cable_state_
calls on it would always return -EINVAL.
This commit fixes this by actually setting info->otg.cable using the new
extcon_get_extcon_dev_by_cable_id function.
This commit also makes failing to register the extcon notifier for the
USB_HOST cable an error rather then a warning, because we MUST have this
notfier to properly disable the VBUS path when in host mode so that we're
not drawing current from the 5V boost converter which is supplying power
to the otg port when in host mode.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Move the charger_init_hw_regs() above the power_supply_register call,
the axp288_charger_usb_set_property() uses axp288_chrg_info.max_cv and
.max_cc which get set by charger_init_hw_regs().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The extcon notifier work calls power_supply_changed on the power_supply
we register, so the extcon notifiers should be registered after we
register the power_supply.
While touching this code anyways, refactor the code for the 3 cable types
into a loop to avoid code repetition.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Use devm_power_supply_register instead of power_supply_register,
this avoids the need to do manual cleanup and results in quite
a nice code cleanup.
Note it may seem excessive to add a "struct device *dev" helper local
variable for the 1 time it is used in this patch, but future patches
in this series also use it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This patch uses the resource-managed extcon API for extcon_register_notifier()
and replaces the deprecated extcon API as following:
- extcon_get_cable_state_() -> extcon_get_state()
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
When the axp288_charger driver was originally merged, it was merged with
a dependency on some other driver providing platform data for it.
However the battery-data-framework which should provide that data never
got merged, so the axp288_charger as merged upstream has never worked,
its probe method simply always returns -ENODEV.
This commit removes the dependency on the platform_data instead reading
back the charging current and charging voltage that the firmware has set
and using those values as the maximum values the user may set.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Make charger_init_hw_regs propagate i2c errors, instead of only warning
about them and then ignoring them.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This moves all power supply drivers from drivers/power/
to drivers/power/supply/. The intention is a cleaner
source tree, since drivers/power/ also contains frameworks
unrelated to power supply, like adaptive voltage scaling.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
