Extend regulator notification support
This series extends the regulator notification and error flag support.
Initial discussion on the topic can be found here:
https://lore.kernel.org/lkml/6046836e22b8252983f08d5621c35ececb97820d.camel@fi.rohmeurope.com/
In a nutshell - the series adds:
1. WARNING level events/error flags. (Patch 3)
Current regulator 'ERROR' event notifications for over/under
voltage, over current and over temperature are used to indicate
condition where monitored entity is so badly "off" that it actually
indicates a hardware error which can not be recovered. The most
typical hanling for that is believed to be a (graceful)
system-shutdown. Here we add set of 'WARNING' level flags to allow
sending notifications to consumers before things are 'that badly off'
so that consumer drivers can implement recovery-actions.
2. Device-tree properties for specifying limit values. (Patches 1, 5)
Add limits for above mentioned 'ERROR' and 'WARNING' levels (which
send notifications to consumers) and also for a 'PROTECTION' level
(which will be used to immediately shut-down the regulator(s) W/O
informing consumer drivers. Typically implemented by hardware).
Property parsing is implemented in regulator core which then calls
callback operations for limit setting from the IC drivers. A
warning is emitted if protection is requested by device tree but the
underlying IC does not support configuring requested protection.
3. Helpers which can be registered by IC. (Patch 4)
Target is to avoid implementing IRQ handling and IRQ storm protection
in each IC driver. (Many of the ICs implementin these IRQs do not allow
masking or acking the IRQ but keep the IRQ asserted for the whole
duration of problem keeping the processor in IRQ handling loop).
4. Emergency poweroff function (refactored out of the thermal_core to
kernel/reboot.c) which is called if IC fires error IRQs but IC reading
fails and given retry-count is exceeded. (Patches 2, 4)
Please note that the mutex in the emergency shutdown was replaced by a
simple atomic in order to allow call from any context.
The helper was attempted to be done so it could be used to implement
roughly same logic as is used in qcom-labibb regulator. This means
amongst other things a safety shut-down if IC registers are not readable.
Using these shut-down retry counters are optional. The idea is that the
helper could be also used by simpler ICs which do not provide status
register(s) which can be used to check if error is still active.
ICs which do not have such status register can simply omit the 'renable'
callback (and retry-counts etc) - and helper assumes the situation is Ok
and re-enables IRQ after given time period. If problem persists the
handler is ran again and another notification is sent - but at least the
delay allows processor to avoid IRQ loop.
Patch 7 takes this notification support in use at BD9576MUF.
Patch 8 is related to MFD change which is not really related to the RFC
here. It was added to this series in order to avoid potential conflicts.
Patch 9 adds a maintainers entry.
Changelog v10-RESEND:
- rebased on v5.13-rc4
Changelog v10:
- rebased on v5.13-rc2
- Move rdev_*() print macros to the internal.h and use rdev_dbg()
from irq_helpers.c
- Export rdev_get_name() and move it from coupler.h to driver.h for
others to use. (It was already in coupler.h but not exported -
usage was limited and coupler.h does not sound like optimal place
as rdev_name is not only used by coupled regulators)
- Send all regulator notifications from irq_helpers.c at one OR'd
event for the sake of simplicity. For BD9576 this does not matter
as it has own IRQ for each event case. Header defining events says
they may be OR'd.
- Change WARN() at protection shutdown to pr_emerg as suggested by
Petr.
Changelog v9:
- rebases on v5.13-rc1
- Update thermal documentation
- Fix regulator notification event number
Changelog v8:
- split shutdown API adding and thermal core taking it in use to
own patches.
- replace the spinlock with atomic when ensuring the emergency
shutdown is only called once.
Changelog v7:
general:
- rebased on v5.12-rc7
- new patch for refactoring the hw-failure reboot logic out of
thermal_core.c for others to use.
notification helpers:
- fix regulator error_flags query
- grammar/typos
- do not BUG() but attempt to shut-down the system
- use BITS_PER_TYPE()
Changelog v6:
Add MAINTAINERS entry
Changes to IRQ notifiers
- move devm functions to drivers/regulator/devres.c
- drop irq validity check
- use devm_add_action_or_reset()
- fix styling issues
- fix kerneldocs
Changelog v5:
- Fix the badly formatted pr_emerg() call.
Changelog v4:
- rebased on v5.12-rc6
- dropped RFC
- fix external FET DT-binding.
- improve prints for cases when expecting HW failure.
- styling and typos
Changelog v3:
Regulator core:
- Fix dangling pointer access at regulator_irq_helper()
stpmic1_regulator:
- fix function prototype (compile error)
bd9576-regulator:
- Update over current limits to what was given in new data-sheet
(REV00K)
- Allow over-current monitoring without external FET. Set limits to
values given in data-sheet (REV00K).
Changelog v2:
Generic:
- rebase on v5.12-rc2 + BD9576 series
- Split devm variant of delayed wq to own series
Regulator framework:
- Provide non devm variant of IRQ notification helpers
- shorten dt-property names as suggested by Rob
- unconditionally call map_event in IRQ handling and require it to be
populated
BD9576 regulators:
- change the FET resistance property to micro-ohms
- fix voltage computation in OC limit setting
Provide helper function for IC's implementing regulator notifications
when an IRQ fires. The helper also works for IRQs which can not be acked.
Helper can be set to disable the IRQ at handler and then re-enabling it
on delayed work later. The helper also adds regulator_get_error_flags()
errors in cache for the duration of IRQ disabling.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/ebdf86d8c22b924667ec2385330e30fcbfac0119.1622628334.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The rdev print helpers are a nice way to print messages related to a
specific regulator device. Move them from core.c to internal.h
As the rdev print helpers use rdev_get_name() export it from core.c. Also
move the declaration from coupler.h to driver.h because the rdev name is
not just a coupled regulator property. I guess the main audience for
rdev_get_name() will be the regulator core and drivers.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/dc7fd70dc31de4d0e820b7646bb78eeb04f80735.1622628333.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds regulator_sync_voltage_rdev(), which is used as a dependency
for new Tegra power domain code.
-----BEGIN PGP SIGNATURE-----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=/dXp
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmDHMi0ACgkQJNaLcl1U
h9Dbvgf/dAcS9d9lgjijzGYcvsh3hBpWqimMrO/dfXlalqXfdU0VN82++0WIcpC7
uoQ2I6RwU4NNTvMUjbmyQsYONMBNthxYEgGDdtwOE03TLVJHc9KyKCzRLFp0E0sX
wHvoAbSZbzd1OIC+96iWJzeC9rq24LX5IaP8301hWKFhbZpo3/uP9yTgQuxSp0cf
tuQDu8vzW7TuC7pxy06FgCmVhsEd2OXEO+wu9OWzMoIAh2Z82KlEb8j0cpV0G0d1
jPdDanaFwJ3LZevbMXZQnJyCGRhFU74vboSC3Vb8e2H7eCwb68s3Z5mo1Dxq6M3o
qE9JGQRgVVOHr67vYXfirOzmhz2D5g==
=5rP3
-----END PGP SIGNATURE-----
Merge tag 'for-5.14-regulator' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into regulator-5.14
regulator: Changes for v5.14-rc1
This adds regulator_sync_voltage_rdev(), which is used as a dependency
for new Tegra power domain code.
Use DEVICE_ATTR_RO() helper instead of plain DEVICE_ATTR(),
which makes the code a bit shorter and easier to read.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20210529115226.25376-1-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some NVIDIA Tegra devices use a CPU soft-reset method for the reboot and
in this case we need to restore the coupled voltages to the state that is
suitable for hardware during boot. Add new regulator_sync_voltage_rdev()
helper which is needed by regulator drivers in order to sync voltage of
a coupled regulators.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
For the boot-on/always-on regulators the set_machine_constrainst() is
called before resolving rdev->supply. Thus the code would try to enable
rdev before enabling supplying regulator. Enforce resolving supply
regulator before enabling rdev.
Fixes: aea6cb9970 ("regulator: resolve supply after creating regulator")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210519221224.2868496-1-dmitry.baryshkov@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The jiffies-based off_on_delay implementation has a couple of problems
that cause it to sometimes not actually delay for the required time:
(1) If, for example, the off_on_delay time is equivalent to one jiffy,
and the ->last_off_jiffy is set just before a new jiffy starts,
then _regulator_do_enable() does not wait at all since it checks
using time_before().
(2) When jiffies overflows, the value of "remaining" becomes higher
than "max_delay" and the code simply proceeds without waiting.
Fix these problems by changing it to use ktime_t instead.
[Note that since jiffies doesn't start at zero but at INITIAL_JIFFIES
("-5 minutes"), (2) above also led to the code not delaying if
the first regulator_enable() is called when the ->last_off_jiffy is not
initialised, such as for regulators with ->constraints->boot_on set.
It's not clear to me if this was intended or not, but I've preserved
this behaviour explicitly with the check for a non-zero ->last_off.]
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20210423114524.26414-1-vincent.whitchurch@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We currently do not respect off_on_delay the first time we turn on a
regulator. This is problematic since the regulator could have been
turned off by the bootloader, or it could it have been turned off during
the probe of the regulator driver (such as when regulator-fixed requests
the enable GPIO), either of which could potentially have happened less
than off_on_delay microseconds ago before the first time a client
requests for the regulator to be turned on.
We can't know exactly when the regulator was turned off, but initialise
off_on_delay to the current time when registering the regulator, so that
we guarantee that we respect the off_on_delay in all cases.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20210422083044.11479-1-vincent.whitchurch@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
s/regulator may on/regulator may already be enabled/
s/or left on/or was left on/
The aim of this patch is to make the comment more readable and to make
it clear, that this is about a regulator, that is already enabled instead
of a regulator that may be switched on.
Signed-off-by: Sebastian Fricke <sebastian.fricke@posteo.net>
Link: https://lore.kernel.org/r/20210421055236.13148-1-sebastian.fricke@posteo.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Sometimes regulator_get() gets called twice for the same supply on the
same device. This may happen e.g. when a framework / library is used
which uses the regulator; and the driver itself also needs to enable
the regulator in some cases where the framework will not enable it.
Commit ff268b56ce ("regulator: core: Don't spew backtraces on
duplicate sysfs") already takes care of the backtrace which would
trigger when creating a duplicate consumer symlink under
/sys/class/regulator/regulator.%d in this scenario.
Commit c33d442328 ("debugfs: make error message a bit more verbose")
causes a new error to get logged in this scenario:
[ 26.938425] debugfs: Directory 'wm5102-codec-MICVDD' with parent 'spi-WM510204:00-MICVDD' already present!
There is no _nowarn variant of debugfs_create_dir(), but we can detect
and avoid this problem by checking the return value of the earlier
sysfs_create_link_nowarn() call.
Add a check for the earlier sysfs_create_link_nowarn() failing with
-EEXIST and skip the debugfs_create_dir() call in that case, avoiding
this error getting logged.
Fixes: c33d442328 ("debugfs: make error message a bit more verbose")
Cc: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210122183250.370571-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Make regulator_sync_voltage() to re-balance voltage state of a coupled
regulators instead of changing the voltage directly.
Tested-by: Peter Geis <pgwipeout@gmail.com> # Ouya T30
Tested-by: Dmitry Osipenko <digetx@gmail.com> # A500 T20 and Nexus7 T30
Tested-by: Nicolas Chauvet <kwizart@gmail.com> # PAZ00 T20
Tested-by: Matt Merhar <mattmerhar@protonmail.com> # Ouya T30
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210122174311.28230-1-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
With commit eaa7995c52 (regulator: core: avoid
regulator_resolve_supply() race condition) we started holding the rdev
lock while resolving supplies, an operation that requires holding the
regulator_list_mutex. This results in lockdep warnings since in other
places we take the list mutex then the mutex on an individual rdev.
Since the goal is to make sure that we don't call set_supply() twice
rather than a concern about the cost of resolution pull the rdev lock
and check for duplicate resolution down to immediately before we do the
set_supply() and drop it again once the allocation is done.
Fixes: eaa7995c52 (regulator: core: avoid regulator_resolve_supply() race condition)
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210122132042.10306-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The final step in regulator_register() is to call
regulator_resolve_supply() for each registered regulator
(including the one in the process of being registered). The
regulator_resolve_supply() function first checks if rdev->supply
is NULL, then it performs various steps to try to find the supply.
If successful, rdev->supply is set inside of set_supply().
This procedure can encounter a race condition if two concurrent
tasks call regulator_register() near to each other on separate CPUs
and one of the regulators has rdev->supply_name specified. There
is currently nothing guaranteeing atomicity between the rdev->supply
check and set steps. Thus, both tasks can observe rdev->supply==NULL
in their regulator_resolve_supply() calls. This then results in
both creating a struct regulator for the supply. One ends up
actually stored in rdev->supply and the other is lost (though still
present in the supply's consumer_list).
Here is a kernel log snippet showing the issue:
[ 12.421768] gpu_cc_gx_gdsc: supplied by pm8350_s5_level
[ 12.425854] gpu_cc_gx_gdsc: supplied by pm8350_s5_level
[ 12.429064] debugfs: Directory 'regulator.4-SUPPLY' with parent
'17a00000.rsc:rpmh-regulator-gfxlvl-pm8350_s5_level'
already present!
Avoid this race condition by holding the rdev->mutex lock inside
of regulator_resolve_supply() while checking and setting
rdev->supply.
Signed-off-by: David Collins <collinsd@codeaurora.org>
Link: https://lore.kernel.org/r/1610068562-4410-1-git-send-email-collinsd@codeaurora.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The function regulator_set_device_supply() is referenced a few times in
comments in regulator/core.c; however this function was removed a long
time ago by commit a5766f11cf ("regulator: core - Rework machine API to
remove string based functions."). Update those references to point to
set_consumer_device_supply(), which replaced the old function.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Link: https://lore.kernel.org/r/20210103165541.784360-1-djrscally@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Selectors lower than linear_min_sel should not be considered invalid.
Thus return zero in case _regulator_list_voltage(),
regulator_list_hardware_vsel() or regulator_list_voltage_table()
receives such selectors as argument.
Fixes: bdcd117757 ("regulator: core: validate selector against linear_min_sel")
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1606325147-606-1-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Hi,
This series adds support for ramp delay on mcp16502. It also adds
some cleanup on mcp16502.
Apart from that patches 1/6 fixes the selector validation in case
the regulator::desc::linear_min_sel is not zero.
Thank you,
Claudiu Beznea
Changes in v3:
- fix compilation error in patch 5/6
Reported-by: kernel test robot <lkp@intel.com>
Changes in v2:
- rebase on top of regulator/for-next
- checked 1/6 and 3/6 applies on top of regulator/for-5.10
Claudiu Beznea (6):
regulator: core: validate selector against linear_min_sel
regulator: core: do not continue if selector match
regulator: mcp16502: add linear_min_sel
regulator: mcp16502: adapt for get/set on other registers
regulator: mcp16502: add support for ramp delay
regulator: mcp16502: remove void documentation of struct mcp16502
drivers/regulator/core.c | 12 +++-
drivers/regulator/helpers.c | 3 +-
drivers/regulator/mcp16502.c | 135 ++++++++++++++++++++++++++++++++++++-------
3 files changed, 127 insertions(+), 23 deletions(-)
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
There are regulators who's min selector is not zero. Selectors loops
(looping b/w zero and regulator::desc::n_voltages) might throw errors
because invalid selectors are used (lower than
regulator::desc::linear_min_sel). For this situations validate selectors
against regulator::desc::linear_min_sel.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1605280870-32432-2-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Workaround regulators whose supply name happens to be the same as its
own name. This fixes boards that used to work before the early supply
resolving was removed. The error message is left in place so that
offending drivers can be detected.
Fixes: aea6cb9970 ("regulator: resolve supply after creating regulator")
Cc: stable@vger.kernel.org
Reported-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Tested-by: Ahmad Fatoum <a.fatoum@pengutronix.de> # stpmic1
Link: https://lore.kernel.org/r/d703acde2a93100c3c7a81059d716c50ad1b1f52.1605226675.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
When a regulator's name equals its supply's name the
regulator_resolve_supply() recurses indefinitely. Add a check
so that debugging the problem is easier. The "fixed" commit
just exposed the problem.
Fixes: aea6cb9970 ("regulator: resolve supply after creating regulator")
Cc: stable@vger.kernel.org
Reported-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Tested-by: Ahmad Fatoum <a.fatoum@pengutronix.de> # stpmic1
Link: https://lore.kernel.org/r/c6171057cfc0896f950c4d8cb82df0f9f1b89ad9.1605226675.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixed commit introduced a possible second call to
set_machine_constraints() and that allocates memory for
rdev->constraints. Move the allocation to the caller so
it's easier to manage and done once.
Fixes: aea6cb9970 ("regulator: resolve supply after creating regulator")
Cc: stable@vger.kernel.org
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Tested-by: Ahmad Fatoum <a.fatoum@pengutronix.de> # stpmic1
Link: https://lore.kernel.org/r/78c3d4016cebc08d441aad18cb924b4e4d9cf9df.1605226675.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
In regulator_late_cleanup when is_enabled failed, don't try to disable
the regulator since it would likely to fail too and causing confusing
error messages.
Signed-off-by: Pi-Hsun Shih <pihsun@chromium.org>
Link: https://lore.kernel.org/r/20201106064817.3290927-1-pihsun@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
regulator_get_voltage_rdev() is called in regulator probe() when
applying machine constraints. The "fixed" commit exposed the problem
that non-bypassed regulators can forward the request to its parent
(like bypassed ones) supply. Return -EPROBE_DEFER when the supply
is expected but not resolved yet.
Fixes: aea6cb9970 ("regulator: resolve supply after creating regulator")
Cc: stable@vger.kernel.org
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reported-by: Ondřej Jirman <megous@megous.com>
Reported-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Tested-by: Ondřej Jirman <megous@megous.com>
Link: https://lore.kernel.org/r/a9041d68b4d35e4a2dd71629c8a6422662acb5ee.1604351936.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
If debugging is disabled, print_constraints() does not print the actual
constraints, but still performs some processing and string formatting,
only to throw away the result later.
Fix this by moving all constraint debug processing to a separate
function, and replacing it by a dummy when debugging is disabled.
This reduces kernel size by almost 800 bytes (on arm/arm64).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201005131546.22448-1-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulator drivers may be defining very long names: this is the
case with the qcom_smd and qcom_spmi regulators, where we need to
parse the regulator parents from DT.
For clarity, this is an example:
{ "l13a", QCOM_SMD_RPM_LDOA, 13, &pm660_ht_lvpldo,
"vdd_l8_l9_l10_l11_l12_l13_l14" },
pm660-regulators {
...
vdd_l8_l9_l10_l11_l12_l13_l14-supply = <&vreg_s4a_2p04>
...
};
Now, with a 32 characters limit, the function is trying to parse,
exactly, "vdd_l8_l9_l10_l11_l12_l13_l14-s" (32 chars) instead of
the right one, which is 37 chars long in this specific case.
... And this is not only the case with PM660/PM660L, but also with
PMA8084, PM8916, PM8950 and others that are not implemented yet.
The length of 64 chars was chosen based on the longest parsed property
name that I could find, which is in PM8916, and would be 53 characters
long.
At that point, rounding that to 64 looked like being the best idea.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Link: https://lore.kernel.org/r/20200926125549.13191-2-kholk11@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When creating a new regulator its supply cannot create the sysfs link
because the device is not yet published. Remove early supply resolving
since it will be done later anyway. This makes the following error
disappear and the symlinks get created instead.
DCDC_REG1: supplied by VSYS
VSYS: could not add device link regulator.3 err -2
Note: It doesn't fix the problem for bypassed regulators, though.
Fixes: 45389c4752 ("regulator: core: Add early supply resolution for regulators")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/ba09e0a8617ffeeb25cb4affffe6f3149319cef8.1601155770.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
Initial support for ROHM BD9576MUF and BD9573MUF PMICs.
These PMICs are primarily intended to be used to power the R-Car family
processors. BD9576MUF includes some additional safety features the
BD9573MUF does not have. This initial version of drivers does not
utilize these features and for now the SW behaviour is identical.
Please note that this version of drivers is only tested on BD9576MUF
but according to the data-sheets the relevant parts of registers should
be same so drivers should also work on BD9573MUF.
This patch series includes MFD, watchdog and regulator drivers with
basic functionality such as:
- Enabling and pinging the watchdog
- configuring watchog timeout / window from device-tree
- reading regulator states/voltages
- enabling/disabling VOUT1 (VD50) when control mode B is used.
This patch series does not bring interrupt support. BD9576MUF and BD9573MUF
are designed to keep the IRQ line low for whole duration of error
condition. IRQ can't be 'acked'. So proper IRQ support would require
some IRQ limiter implementation (delayed unmask?) in order to not hog
the CPU.
---
Matti Vaittinen (6):
dt_bindings: mfd: Add ROHM BD9576MUF and BD9573MUF PMICs
dt_bindings: regulator: Add ROHM BD9576MUF and BD9573MUF PMICs
mfd: Support ROHM BD9576MUF and BD9573MUF
wdt: Support wdt on ROHM BD9576MUF and BD9573MUF
regulator: Support ROHM BD9576MUF and BD9573MUF
MAINTAINERS: Add ROHM BD9576MUF and BD9573MUF drivers
.../bindings/mfd/rohm,bd9576-pmic.yaml | 129 +++++++
.../regulator/rohm,bd9576-regulator.yaml | 33 ++
MAINTAINERS | 4 +
drivers/mfd/Kconfig | 11 +
drivers/mfd/Makefile | 1 +
drivers/mfd/rohm-bd9576.c | 130 +++++++
drivers/regulator/Kconfig | 10 +
drivers/regulator/Makefile | 1 +
drivers/regulator/bd9576-regulator.c | 337 ++++++++++++++++++
drivers/watchdog/Kconfig | 13 +
drivers/watchdog/Makefile | 1 +
drivers/watchdog/bd9576_wdt.c | 295 +++++++++++++++
include/linux/mfd/rohm-bd957x.h | 61 ++++
include/linux/mfd/rohm-generic.h | 2 +
14 files changed, 1028 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mfd/rohm,bd9576-pmic.yaml
create mode 100644 Documentation/devicetree/bindings/regulator/rohm,bd9576-regulator.yaml
create mode 100644 drivers/mfd/rohm-bd9576.c
create mode 100644 drivers/regulator/bd9576-regulator.c
create mode 100644 drivers/watchdog/bd9576_wdt.c
create mode 100644 include/linux/mfd/rohm-bd957x.h
base-commit: f4d51dffc6
--
2.21.0
--
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND
~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =]
The biggest set of fixes here is those from Michał Mirosław fixing some
locking issues with coupled regulators that are triggered in cases where
a coupled regulator is used by a device involved in fs_reclaim like eMMC
storage. These are relatively serious for the affected systems, though
the circumstances where they trigger are very rare.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl9baDITHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0NAOCACGwc1Rxsr9cMDY5vQS7AHzfPVRdoQJ
Z9KIOQT9ER0hFHRNh1/t1n/p4DcK+3ke0MH/R/VndijvePJgHyL01Bsjq92iDiIy
b80nDJwRwLWWdvKAPG5JklVK8pL/6LxaC9eL8zK93Hm4fGkNJzBi7jF2++jep/tB
2jRM4Vrq8B0dkh/jPQMscl4Z66purIiyKLJjy1QFjXXq0/jkjZizURy+aofS3uJD
0vebim9OI7z0H4g6cflJrHUAuDraNmGCfGAyUMH7AESJlUGNRk7BzNYT51tLVYqG
ithNZDh/AbWhGzntuUUKNlM4D8p26FNJmU51crh33kBH3va737dvc/BT
=3fwP
-----END PGP SIGNATURE-----
Merge tag 'regulator-fix-v5.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"The biggest set of fixes here is those from Michał Mirosław fixing
some locking issues with coupled regulators that are triggered in
cases where a coupled regulator is used by a device involved in
fs_reclaim like eMMC storage.
These are relatively serious for the affected systems, though the
circumstances where they trigger are very rare"
* tag 'regulator-fix-v5.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: pwm: Fix machine constraints application
regulator: core: Fix slab-out-of-bounds in regulator_unlock_recursive()
regulator: remove superfluous lock in regulator_resolve_coupling()
regulator: cleanup regulator_ena_gpio_free()
regulator: plug of_node leak in regulator_register()'s error path
regulator: push allocation in set_consumer_device_supply() out of lock
regulator: push allocations in create_regulator() outside of lock
regulator: push allocation in regulator_ena_gpio_request() out of lock
regulator: push allocation in regulator_init_coupling() outside of lock
regulator: fix spelling mistake "Cant" -> "Can't"
regulator: cros-ec-regulator: Add NULL test for devm_kmemdup call
Since 3801b86aa4 ("regulator: Refactor supply implementation
to work as regular consumers") we no longer cascade notifications
and so notifier head's built-in rwsem is enough to protect the
notifier chain. Remove the requirement to fix one case where
rdev->mutex might be forced to be taken recursively.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/5a0da9017c69a4dbc3f9b50f44476fce80a73387.1597032945.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
The recent commit 7d8196641e ("regulator: Remove pointer table
overallocation") changed the size of coupled_rdevs and now KASAN is able
to detect slab-out-of-bounds problem in regulator_unlock_recursive(),
which is a legit problem caused by a typo in the code. The recursive
unlock function uses n_coupled value of a parent regulator for unlocking
supply regulator, while supply's n_coupled should be used. In practice
problem may only affect platforms that use coupled regulators.
Cc: stable@vger.kernel.org # 5.0+
Fixes: f8702f9e4a ("regulator: core: Use ww_mutex for regulators locking")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200831204335.19489-1-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For systems that have eg. eMMC storage using voltage regulator, memory
reclaim path might call back into regulator subsystem. This means we
have to make sure no allocations happen with a regulator or regulator
list locked.
After this series I see no more lockdep complaints on my test system,
but please review and test further.
First four patches move allocations out of locked regions, next three
came as a drive-by cleanups.
---
v2: fix bug in patch #4 spotted by kernel test robot
reworded commit #7 description
Michał Mirosław (7):
regulator: push allocation in regulator_init_coupling() outside of
lock
regulator: push allocation in regulator_ena_gpio_request() out of lock
regulator: push allocations in create_regulator() outside of lock
regulator: push allocation in set_consumer_device_supply() out of lock
regulator: plug of_node leak in regulator_register()'s error path
regulator: cleanup regulator_ena_gpio_free()
regulator: remove superfluous lock in regulator_resolve_coupling()
drivers/regulator/core.c | 164 +++++++++++++++++++++------------------
1 file changed, 87 insertions(+), 77 deletions(-)
--
2.20.1
I see it takes about 5us per regulator to grab the lock, check that this
regulator isn't going to do anything for suspend, and then release the
lock. When that is combined with PMICs that have dozens of regulators we
get into a state where we spend a few miliseconds doing a bunch of
locking operations synchronously to figure out that there's nothing to
do. Let's reorganize the code here a bit so that we don't grab the lock
until we're actually going to do something so that suspend is a little
faster.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200804070837.1084024-1-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The code modifies rdev, but locks c_rdev instead. Remove the lock
as this is held together by regulator_list_mutex taken in the caller.
Fixes: f9503385b1 ("regulator: core: Mutually resolve regulators coupling")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/25eb81cefb37a646f3e44eaaf1d8ae8881cfde52.1597195321.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
