This is a merge of really big changes: the generic parser is heavily
enhanced for handling all cases, based on the former Realtek codec
driver code. And all codec drivers except for a few ones (CA0132,
HDMI and modem) have been converted to use the new generic driver.
Conflicts:
sound/pci/hda/patch_realtek.c
Now all AD codecs have the proper BIOS auto-parser, and we can make
it for default, finally. (AD1988 already did it because it had the
auto-parser.)
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As done for patch_conexant.c, put ifdef ENABLE_AD_STATIC_QUIRKS for
preparing t odrop the static quirk codes in patch_analog.c.
The whole static quirk code can be omitted by commenting out
ENABLE_AD_STATIC_QUIRKS define now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Convert all uses of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AD codecs have strange implementations for choosing the SPDIF-output
mux source: the digital audio out widget may take the sources from
multiple connections, where 0x01 indicates it's a PCM while others
point ADCs. It's obviously invalid in the HD-audio spec POV, but it's
somehow convincing, too. And, to make things more complex, AD1988A
and AD1882 have deeper connection routes that aren't expressed
correctly.
In this patch, the SPDIF mux control is implemented in two ways:
- For easier one like AD1981, AD1983, AD1884 and AD1984, where the
SPDIF audio out widget takes just two or three sources, we can
simply implement via the normal input_mux and connection verb
calls.
- For the complex routes like AD1988A (but not AD1988B) or AD1882, we
prepare "faked" paths represented statically, and switch the paths
using these static ones, instead of parsing the routes from the
widget tree.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since both snd_hda_codec_flush_amp_cache() and
snd_hda_codec_flush_cmd_cache() are called usually at the same time,
we can simply combine them to a single function,
snd_hda_codec_flush_cache().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The capture volume put callback may call the node selection change,
and its actual call won't be triggered unless flushed. In general,
we always need to call both snd_hda_codec_flush_amp_cache() and
snd_hda_codec_flush_cmd_cache() at the same place...
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Both the HP auto-mute and the independent HP mode conflict with each
other. Make HP auto-mute disabled (only for the affected HP jack)
during the driver is in HP independent mode.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It'd be better to give another name to the secondary (alt) analog PCM
stream, which is dedicated for the independent HP out and extra
inputs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The aamix NIDs are also missing for AD codecs. All AD codecs seem to
have a (more or less) working aamix widget.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch correctly releases the firmware if the magic string in the
firmware header does not match.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch correctly releases the firmware if the magic string in the
firmware header does not match.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
IDT codecs have analog-loopback mixer widgets, but we haven't cared
about it, so far. Let's set them. This will avoid also possible
wrong routes for the input paths.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch eventually fixes two issues:
- Handle the case where the primary output is a headphone and can have
independent HP mode;
so far we checked only the case where the headphone is the secondary
output.
- Fix the conflict of HP independent mode and aamix mode;
when switched to aamix mode, the DAC might be also switched to
another widget shared with other outputs. Then even if we disable
the DAC for the original output, it doesn't change -- because the
active route is from another (shared) DAC to HP pin through aamix.
So, in such a case, we have to prohibit the switch to aamix for HP
routes.
This fixes issues appearing on VT codecs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Many codecs provide routes to multiple output pins through an aamix
widget, but most of them do it only from a single DAC. However, the
current generic parser checks only the aamix paths from the original
(directly bound) DACs through aamix NID, and miss the path:
primary DAC -> aamix -> target out pin
This patch adds a more check for the routes like the above.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a patch couldn't be resolved in try_assign_dacs() although the
target DAC is expected, we forgot to add a proper badness value but
continued.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since fill_and_eval_dacs() may be called repeatedly with different
configurations, setting pinctls at each time there isn't optimal.
We can set it better only once after deciding the output configuration
in parse_output_paths().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Print the information of outputs in a bit more details and concisely
in a single place instead of printing the path at each time when
detected.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Place a cap on the number of channels clocks are generated for. This is
intended for use with systems which have the WM5102 master an I2S bus with
multiple data lines.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some systems may wish to support switching between telephony and CD audio
clock rates but this is restricted by enforcement of constraints on the
current DAI clock. Support setting clocks to zero and don't enforce any
constraints in that case in order to facilitate this use case.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix up all callers as they were before, with make one change: an
unsigned module taints the kernel, but doesn't turn off lockdep.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Normally kmalloc() returns things that are DMA safe so not visible on all
platforms but we do need to explicitly request DMA safe memory.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Normally kmalloc() returns things that are DMA safe so not visible on all
platforms but we do need to explicitly request DMA safe memory.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The option allows you to remove TTY and compile without errors. This
saves space on systems that won't support TTY interfaces anyway.
bloat-o-meter output is below.
The bulk of this patch consists of Kconfig changes adding "depends on
TTY" to various serial devices and similar drivers that require the TTY
layer. Ideally, these dependencies would occur on a common intermediate
symbol such as SERIO, but most drivers "select SERIO" rather than
"depends on SERIO", and "select" does not respect dependencies.
bloat-o-meter output comparing our previous minimal to new minimal by
removing TTY. The list is filtered to not show removed entries with awk
'$3 != "-"' as the list was very long.
add/remove: 0/226 grow/shrink: 2/14 up/down: 6/-35356 (-35350)
function old new delta
chr_dev_init 166 170 +4
allow_signal 80 82 +2
static.__warned 143 142 -1
disallow_signal 63 62 -1
__set_special_pids 95 94 -1
unregister_console 126 121 -5
start_kernel 546 541 -5
register_console 593 588 -5
copy_from_user 45 40 -5
sys_setsid 128 120 -8
sys_vhangup 32 19 -13
do_exit 1543 1526 -17
bitmap_zero 60 40 -20
arch_local_irq_save 137 117 -20
release_task 674 652 -22
static.spin_unlock_irqrestore 308 260 -48
Signed-off-by: Joe Millenbach <jmillenbach@gmail.com>
Reviewed-by: Jamey Sharp <jamey@minilop.net>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Conexant CX20551 codec has a mixer in NID 0x19 and a few outputs have
to take the input through this widget.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Looking through the whole definitions, some fields have inappropriate
array sizes, especially about the capture. The array assigned to each
input (pin) should have HDA_MAX_NUM_INPUTS entries while the array
assigned to each ADC should have AUTO_CFG_MAX_INS entries.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The patch "ALSA: hda - fix wrong adc_idx in generic parser" fixed the
adc_idx for the capture volume and capture switch controls. But also
modified the adc_idx retrieval for the capture source controls
wrongly. As multiple capture source controls are created in a single
shot with counts > 1, the id.index doesn't contain the real value.
The real index has to be taken via snd_ctl_get_ioffidx() as in the
original code.
This patch reverts the fixes partially to recover from the
regression.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If there's one each of HDMI and SPDIF, we should not add an index
on the one that comes second.
[slight code refactoring by tiwai]
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just stumbled over this one while reading the code.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I found a codec configuration which had six inputs, so the max of
five was not appropriate.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some BIOS version of FSC Lifebook S7110 laptop seems to give a wrong
default pin config for NID 0x15, which confuses the parser. Give a
fixup to correct the value.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Although I commented that boost volumes would be added only for
line-in and mic pins in the source code, the actual code excludes but
for mic-in. Fix it to accept the line-ins, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Two hooks in hda_gen_spec, cap_sync_hook and capture_switch_hook, play
very similar roles. The only differences are that the former is
called more often (e.g. at init or switching capsrc) while the latter
can take an on/off argument.
As a more generic implementation, consolidate these two hooks, and
pass snd_ctl_elem_value pointer as the second argument. If the
secondary argument is non-NULL, it can take the on/off value, so the
caller handles it like the former capture_switch_hook. If it's NULL,
it's called in the init or capsrc switch case.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a standard capture switch without multiple binding is used, the
call for capture_switch_hook isn't called properly. Replace the put
ops to add the hook call in that case.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This machine also has the "HP_Mute_LED_0_A" string in DMI information.
Cc: <stable@vger.kernel.org>
BugLink: https://bugs.launchpad.net/bugs/1096789
Tested-by: Tammy Yang <tammy.yang@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the current generic parser code, we look for the (mic) boost
controls only on input pins. But many codecs assign the boost volume
to a widget connected to each input pin instead of the input amp of
the pin itself.
In this patch, the parser tries to look through more widgets connected
to the pin and find a boost amp.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When an amp in the activation path is associated with mixer controls,
activate_amp() tries to skip the initialization. It's good, but only
if the mixer really initializes both mute and volume. Otherwise,
either the mute of the volume is left uninitialized.
This patch adds this missing check and properly initialize the
partially controlled amps in an activation path.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are a few places creating the labels and indices of kctls for
each input pin in the current generic parser code. This is redundant
and makes harder to maintain. Let's create the labels and indices at
once and keep them in hda_gen_spec.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since the imux table entries can be a subset of autocfg.input table,
the indices of these aren't always same. For passing the proper index
value of autocfg.input at creating input ctl labels (via
snd_hda_autocfg_input_label()), keep the corresponding autocfg.input
idx value in the index field of each imux item, which isn't used in
the generic driver.
Also, this makes easier to check the invalid imux pin for stereo mix.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Sets the ADSP1 clock rate to match the system clock
rate. To support this the codec driver provides
details of register containing the system clock
control bits.
Signed-off-by: Chris Rattray <crattray@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Implement support for a new revision of the coefficeint file format for
ADSP cores.
Since coefficient file format 0 has not been widely deployed and is very
unlikely to ever be used with this driver code support for it has been
removed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Finally we reached here. All codecs driver (except for CA0132, which
has really device-specific requirements) have been converted to use
the generic parser.
This patch appears bigger than others since it also involves with the
code shuffling, but mostly the cut-off of parser codes and adapt to
the generic parser flags. Most of fixup codecs haven't been changed
but just removed a few unnecessary codes.
The only missing stuff is the SPDIF mux control. It'll be added again
later.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* test/hda-gen-parser:
ALSA: hda - Improve naming rule for primary output
ALSA: hda - Add PCM capture hook to hda_gen_spec
ALSA: hda - Record all detected ADCs in hda_gen_spec
ALSA: hda - Move vmaster TLV parsing to snd_hda_gen_parse_auto_config()
ALSA: hda - Add input jack mode enum controls to generic parser
ALSA: hda - Give more comments to hda_gen_spec flags
ALSA: hda - Add suppress_auto_mute flag to hda_gen_spec
ALSA: hda - Record the current speaker / LO mute status in hda_gen_spec
ALSA: hda - Properly call automute/switch hooks at init
When the volume or mute control of the primary output is shared with
other (headphone or speaker) outputs, we shouldn't name it as a
specific output type but rather name it with the channel name or a
generic name like "PCM".
Also, this check should be performed individually for the volume and
the mute controls because some codecs may have shared volumes but
separate mute controls.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since the generic parser reduces the ADC list, copy the list of the
all detected ADCs and keep it.
This list can be later referred by the codec driver for finer power
controls.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add vmaster_tlv[] to hda_gen_spec and store the suggested TLV data
in snd_hda_gen_parse_auto_config(). This allows the codec driver to
correct the TLV data (e.g. mute capability) before actually creating
vmaster instance.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just like the jack mode enum ctls for output jacks, add the support
for similar enum ctls for input pins to control the bias Vref.
The new controls will be added when spec->add_in_jack_modes is set
either by the codec driver or by a hint string.
Note that ground and 100% vrefs are excluded from the list for
simplicity, currently. We may add a new flag to allow them, too.
But I guess it's easier to put a value override in the pinfix in such
a case.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- spec->hp_detect has to be overridden in HDA_FIXUP_ACT_PARSE, not in
PRE_PARSE.
- Remove err == 0 check but return directly -EINVAL from
stac92xx_parse_auto_config()
- Set spec->default_polarity for 92HD71bxx
- Some code shuffles
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This adds a very simple machine driver using the Wolfson wm9712 AC97
codec.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Otherwise we'll get the wrong LRCLK if we need to pick a higher BCLK than
is required.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
A new flag to skip the auto-mute handling in the generic parser, just
like suppress_auto_mic flag. It has to be set before calling
snd_hda_gen_parse_auto_config().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* test/hda-gen-parser:
ALSA: hda - Make sure fill_all_dac_nids is called for digital only codecs
ALSA: hda - force different capture controls if amp caps differ
ALSA: hda - do not add non-existing Mic boost controls
ALSA: hda - initialize channel counts correctly
ALSA: hda - fix wrong adc_idx in generic parser
ALSA: hda - Check array bounds in get_input_path
ALSA: hda - Add prefer_hp_amp flag to hda_gen_spec
ALSA: hda - fix OOPS in hda_mark_cmd_cache_dirty
ALSA: hda - Check pincap while parsing the configuration
Otherwise no PCM will be built for codecs without analog I/O.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Otherwise setting the capture volume for amps will be weird and
inconsistent (it will try to set values outside the range of the
second amp based on capabilities of the first amp).
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If the input node does not have any volume capable input amp,
don't add such a control.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Chris Rattray <crattray@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
__devinitconst and friends have recently been removed and must not be
used anymore.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Even a single DAC can output two channels, so the channel count
is twice the number of DACs.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We use knew->index for adc_idx when we create "Capture Volume" and
"Capture Switch", so use the same to retrieve adc_idx.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We only log the result and since the interrupt triggers on loss of lock
during shutdown this may lead to spurious interrupts during shutdown
delaying the process.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
sound/pci/hda/patch_ca0132.c:387:19: sparse: symbol 'ca0132_voicefx' was not declared. Should it be static?
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With HDSP_TOGGLE_SETTING in place, these functions are no longer
required. Removing them makes the code DRY and considerably shorter.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDSP_TOGGLE_SETTING and its corresponding functions allow to change
settings in the control register. Instead of using the specialised
functions, use the generic code to make the code DRY.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The driver contains multiple similar functions that change only a single
bit in the control register, only the bit position varies.
This patch implements a generic function to toggle a certain bit
position that will be used to replace the old code.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current iobox detection code reportedly fails for various users, so
simply do what the Win32 driver does instead.
Patch originally by Karl Grill <kgrill@chello.at> and then modified to
comply with kernel coding guidelines + current HEAD.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a new flag to indicate whether HP amp is turned on as default for
speaker or line-outs, and enable this for ALC260 codec, as many
machines with this codec require the HP amp even for speakers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
sound/pci/hda/patch_ca0132.c: In function ‘ca0132_effects_set’:
sound/pci/hda/patch_ca0132.c:3391:2: warning: too many arguments for
format [-Wformat-extra-args]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Spotted by smatch,
sound/pci/hda/patch_ca0132.c:1950 dspxfr_image() error: potential
null dereference 'dma_engine'. (kzalloc returns null)
sound/pci/hda/patch_ca0132.c:1950 dspxfr_image() error: we
previously assumed 'dma_engine' could be null (see line 1857)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
sound/pci/hda/patch_ca0132.c:1781 dspxfr_one_seg() info: why not
propagate 'status' from dsp_dma_stop() instead of (-5)?
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent update of ca0132 driver replaced the pinctl setup to the
direct write via snd_hda_codec_write() again. This should be covered
by snd_hda_set_pin_ctl() to be safer.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This reverts commit c3b4eea262.
Since the recent firmware loader code supports caching at S3/S4 by
itself, we don't have to handle f/w caching in the driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Handle a potential dma_engine alloc error and fix the possible use of an
uninitialized status variable in dspxfr_one_seg(). Also correct the initial
sampling rate for Mic 1.
Update the module description.
Signed-off-by: Ian Minett <ian_minett@creativelabs.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the controls used for tuning the DSP effects.
Signed-off-by: Ian Minett <ian_minett@creativelabs.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the unsolicited response handler for incoming DSP responses and
jack detection reporting, and routines for reading the incoming DSP response.
Signed-off-by: Ian Minett <ian_minett@creativelabs.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove the playback PCM open callback.
PCM stream setup and cleanup functions are added for use by PCM callbacks.
Delay stream cleanup if effects are on, to allow time for any effects tail to
finish.
Add the analog capture PCM callbacks.
Change the max channels of analog playback to 6.
Add two new PCMs: AMic2 and What-U-Hear.
Signed-off-by: Ian Minett <ian_minett@creativelabs.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the kcontrols for the DSP effects, playback and recording
source selection.
ca0132_is_vnode_effective() checks whether virtual node settings have
taken effect.
The control change helpers ca0132_pe_switch_set(), ca0132_voicefx_set()
and ca0132_cvoice_switch_set() are added to toggle playback / capture
DSP effects, ca0132_voicefx_info(), _get() and _put() are added for
input path DSP effect value access. The volume helpers are updated to
volume_info(), _get() and _set() to use the virtual nodes.
The redundant headphone and speaker switches and ct_extension function
are removed.
Signed-off-by: Ian Minett <ian_minett@creativelabs.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the framework to set effect parameters: ca0132_effects_set()
and ca0132_setup_defaults() are general functions for parameter setting and
initializing to default values. dspio_set_param() and dspio_set_uint_param()
are lower-level fns to simplify setting individual DSP parameters via an
SCP buffer transfer to the firmware.
The CA0132 chip parameter init code is added in ca0132_init_params().
In chipio_[write,read]_data(), the current chip address is auto-incremented
if no error has occurred.
ca0132_select_out() selects the current output. If autodetect is enabled,
use headphones (if jack detected) or speakers (if no jack).
ca0132_select_mic() selects the current mic in. If autodetect is enabled,
use exterior mic (if jack detected) or built-in mic (if no jack).
Init digital mic and switch between dmic and amic with ca0132_init_dmic(),
ca0132_set_dmic(). amic2 is initialized in ca0132_init_analog_mic2().
Finally, add verb tables for configuring DSP firmware.
Signed-off-by: Ian Minett <ian_minett@creativelabs.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds definitions and structs used for configuring DSP effects,
virtual nodes, effect tuning controls, and mixer control helpers.
The effect structs are also initialized.
Signed-off-by: Ian Minett <ian_minett@creativelabs.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When "alsactl restore" is performed on HDMI codecs, it tries to
restore the channel map value since the channel map controls are
writable. But hdmi_chmap_ctl_put() returns -EBADFD when no PCM stream
is assigned yet, and this results in an error message from alsactl.
Although the error is harmless, it's certainly ugly and can be
regarded as a regression.
As a workaround, this patch changes the return code in such a case to
be zero for making others happy. (A slight excuse is: when the chmap
is changed through the proper alsa-lib API, the PCM status is checked
there anyway, so we don't have to be too strict in the kernel side.)
Cc: <stable@vger.kernel.org> [v3.7+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of checking the codec SSID in find_mute_led_cfg() for HP Mini
110, set the proper spec->default_polairty in the fixup table.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PCI vendor ID check in find_mute_led_cfg() is now superfluous
because the function is called in the fixup table entries of HP
machines.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Finally all codecs in patch_sigmatel.c have been converted to use the
standard fixup helpers. This change also includes trivial cleanups
like the call of common setup for GPIO LED or the removal of unused
function.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This one is rather a simple conversion. The fixups for Dell machines
are implemented by fixup functions in the end.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This time, the only intrusive changes are for HP machines.
As the mute LED fixup and the bass speaker switch are required only
for HP machines, we can move these checks into the fixup entries; the
former is applied generically to all HP machines while the latter for
only certain models.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Sometimes (or rather often) BIOS sets the pin default configurations
obviously wrongly. Looking through these failures, one common pattern
is to enable some dead pins that are usually marked as speaker pins.
In such a case, we can skip them if the pins don't have the output
capability.
In this patch, add a check for the valid pin cap bit for each parsed
pin, and filter out when it's invalid.
The fix was originally suggested by Raymond Yau.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This conversion is a bit tricky. Since STAC927x may take two
different volume-knob initialization values depending on the model, a
new flag, spec->volknob_init, is introduced to indicate whether it's
the standard volume-knob initialization or not.
Also, Dell BIOS model is now directly mapped onto the fixup table
instead of parsing in the function. This resulted in a new model ref,
STAC_927X_DELL_BIOS_SPDIF, which is a chained entry.
Also, for reducing the fixups, virtual entries like
STAC_927X_DELL_DMIC and STAC_D965_VERBS are introduced.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Rather straightforward conversion, except for ones for Intel Mac.
As Intel Mac have only unique codec SSIDs, we need to remap the fixup
again for the codec SSID and call the new fixup there.
Also, we can reduce model enums like STAC_MACMINI, which are model
aliases for backward compatibility, since they can be pointed directly
via hda_model_fixup table.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add names of the clock sources for the M-Audio Fast Track
C400.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Attain constant real-world latency by skipping 16 data packets.
The number of packets to be skipped was found by trial and error.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Taking another look at the C400 descriptors, I see now that there is
a clock selector (0x80) for this device.
Right now, the clock source points to the internal clock (0x81), which
is also valid. When the external clock source (0x82) is selected in the
mixer, and the rates mismatch (if it's free-running it is fixed to
48KHz), xruns will occur.
Set the clock ID to the clock selector unit (0x81), which then
allows the validation code to function correctly.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A patch in the 3.2 kernel caused regression with hotplugging the
M-Audio Fast track pro, or sound after suspend. I don't have the
device so I haven't done a full analysis, but it seems userspace
(both udev and pulseaudio) got confused when a card was created,
immediately destroyed, and then created again.
However, at least one person in the bug report (martin djfun)
reports that this patch resolves the issue for him. It also leaves
a message in the log:
"snd-usb-audio: probe of 1-1.1:1.1 failed with error -5" which is
a bit misleading. It is better than non-working audio, but maybe
there's a more elegant solution?
BugLink: https://bugs.launchpad.net/bugs/1095315
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CONFIG_HOTPLUG is always true now and the __dev* macros have been removed.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Support for loading the Renesas FSI driver via devicetree.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This adds the driver for the Tegra 2x AC97 host controller.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current simple-card driver calls asoc_simple_card_dai_init()
if platform had a asoc_simple_card_dai_init pointer.
And, this initialization function works only
when platform has an applicable initial value for each dai settings.
And basically, almost all sound card requires certain initialization.
This means that almost all platform has initialization settings,
and driver do nothing if it doesn't have settings.
And additionally, current simple-card supports sysclk settings but it was
only for codec. In order to abolish deviation between cpu and codec,
and in order to simplify processing,
this patch adds asoc_simple_dai, and removed pointless
struct asoc_simple_dai_init_info which was trigger of
calling asoc_simple_card_dai_init().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
With idle_bias_off these are no longer needed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There are many firmwares available for ADSP devices. Add basic support
for selecting between them, including a couple of feature sets in the
set of available firmware to start off with.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Yet another step forward. As all features for VIA codecs have been
implemented in the generic driver, we can move on to migrate the VIA
codec parser, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the support for the generic auto-parser to AD codec
driver. For AD1988, the old code is replaced simply with the new
generic parser. For other codecs, new model "auto" is added and
directed to use the generic parser.
No fixup codes have been implemented yet as of now. Eventually we'd
replace each static quirk with the generic parser + fixup.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just shuffle the codes and add ifdefs for testing to drop the static
quirk codes from patch_conexant.c.
By commenting out ENABLE_CXT_STATIC_QUIRKS define at the beginning of
the file, you can disable the whole static codes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This time, the target is Cirrus codec. Its parser is a subset of
generic parser, so we can migrate fully with it now.
The only tricky part is the handling of SPDIF automute.
Cirrus driver sets the SPDIF out plug over the headphone. As a
workaround, set spec->gen.master_mute for toggling the headphone (and
other) mute.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CA0110 codec is a fairly straightforward hardware implementation,
and we can use the generic parser almost as is.
Just set spec->multi_cap_vol flag to follow the current behavior.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace the old parser code for C-Media auto-parser with the latest
generic parser. For compatibility reason, the static bindings are
still left, but they could be cleaned up in future.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The pincfgs, init_verbs and hints set by sysfs or patch might be
changed dynamically on the fly, thus we need to protect it.
Add a simple protection via a mutex.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As David Henningsson recently suggested, some HP laptops use an unused
mic pin for controlling a mute LED, and this information is provided
via DMI string "HP_Mute_LED_X_Y" string. This patch adds the generic
support for such cases, as we've already done in patch_sigmatel.c.
This is applied generically to all devices with ID 0x103c.
But as we don't know whether the device 103c:1586 really contains
HP_Mute_LED_X_Y DMI string, still keep the static setup for this
device using the mic2 pin 0x19.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some fixups such as setting the flags influencing on the parser
behavior should be applied before actually parsing the tree.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Try to recover from the regression: set the HP amp for the speaker and
add the hp jack mode enum as default.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the enum controls for changing the headphone amp bits of output
jacks, such as "Headphone Jack Mode". This feature isn't enabled as
default, so far, unless spec->add_out_jack_modes flag is set.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a multi-io jack is switched to another direction, call the
automute and autoswitch update functions, as this jack won't be used
as the headphone or the mic jack that may turn off others.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a new fixup type, HDA_FIXUP_PINCTLS, for overriding the pinctl
values of the given pins. It takes the same array of struct pintbl
like HDA_FIXUP_PINS, but each entry contains the pinctl value instead
of the pin default config value.
This patch also replaces the corresponding codes in patch_realtek.c.
Without this change, the direct call of verbs may be overridden again
by the later call of pinctl restoration by the driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now the whole codebase has been changed from the earlier kernels, it
makes little sense to keep these aliases. Simply replace with the
official names.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a jack is retasked as a different direction (e.g. a mic jack is
used as a CLFE output), such a jack shouldn't be counted as the target
for the automatic jack switching. Skip the automute or the autoswitch
when the current pinctl direction is different from what we suppose.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the new pin target accessors for managing the current pinctl
values in the generic parser. The pinctl values of all active pins
are once determined at the initialization phase, and stored via
snd_hda_codec_set_pin_target(). This will be referred again in the
codec init or resume phase to set the actual pinctl.
This value is kept while the auto-mute. When a line-out or a speaker
pin is muted by auto-mute, the driver simply disables the pin, but it
doesn't touch the cached pinctl target value. Upon unmute, this value
is used to restore the original pinctl in return.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Check more strictly about the validity of pinctl values in
snd_hda_set_pin_ctl() and correct the wrong bits automatically.
Also provide the helper function to correct pinctl bits to codec
drivers.
This automatically fixes the invalid pinctl writes that are found in
a few Realtek fixups for NID 0x0f amp like ASUS A6Rp.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We already have the list of whole pin widgets and there is an unused
space in the list; let's use it for caching the current pinctl value.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a DAC is reassigned from surrounds to front or ADCs are reduced
due to incomplete imux, we clear the path indices but the path
instances remain as is. Since the paths might be still referred
through the whole path list parsing (e.g. is_active_nid()), we should
clear these path instances as well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since some codecs can choose the aamix as a capture source, we should
support it as well. When spec->add_stereo_mix_input flag is set, the
parser checks the availability of aamix as the input source, and adds
the paths automatically when possible.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the current parser code, the input_paths[] may become inconsistent
when some of detected ADCs are dropped due to incomplete inputs, since
the driver rearranges only adc_nids[] but doesn't touch input_paths[].
This patch fixes the issue, and also it optimizes the reachability
checks by simply referring to the parsed input_paths[] instead of
calling is_reachable() again for each connection.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of handling special cases in the caller side, give a proper
name string "Headphone Mic" from hda_get_autocfg_input_label() when
the headhpone jack pin is specified as an input.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The capture paths shouldn't contain the analog loopback mixer.
Pass a proper argument to exclude the aamix NID.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a new flag spec->suppress_mic_auto_switch for codecs that don't
support unsol events properly like VT1708.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the default config value shows the connection AC_JACK_PORT_BOTH,
it's better to handle it as a speaker pin. This makes the behavior
consistent in snd_hda_get_pin_label() and snd_hda_parse_pin_defcfg().
There are only few old machines showing this attribute, and all of
them are actually fixed speaker pins, as far as I know.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit modifies the definition of snd_hda_parse_nid_path()
slightly, now with_aa_mix argument is changed to anchor_nid, so that
it can handle any NID generically as an anchor point to include or
exclude.
The with_aa_mix field in struct nid_path is removed again by this
change.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The multi-io channels can vary not only from 1 to 6 but also may vary
from 6 to 8 or such. At the same time, there are more speaker pins
available than the primary output pins. So, we need three variables
to check: the minimum channel counts for primary outputs, the current
channel counts for primary outputs, and the minimum channel counts for
all outputs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of looking through paths with the dac -> pin connection at
each time, just pass the already parsed path index to
assign_out_path_ctls(). This simplifies the code a bit.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The path indices must be reset at each evaluation of DAC assignment.
Otherwise the badness value will be wrongly calculated and mixers may
be inconsistently assigned.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Let is_jack_detectable() return true when the jack polling is enabled
for the codec. VT1708 uses the polling explicitly so we need to allow
it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The new hook which is called at each PCM playback ops.
It can be used to control the codec-specific power-saving feature in
each codec driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The bind-volume workaround was introduced for simplifying the mixer
abstraction in the case where one or more pins of multiple outputs
lack of individual volume controls. This was essentially the case
like Acer Aspire 5935, which has 5.1 speakers and 5.1 (multi-io)
jacks although there are 5 DACs, so some of them must share a DAC.
However, the recent code rewrite changed the DAC assignment policy to
share with the same channel instead of binding to the front, thus
binding the volumes for all channels makes little sense now, rather
it's confusing. So in this patch, the ugly workaround is finally
dropped and simply create the volume control corresponding to the
parsed path position.
For dual headphones or 2.1 speakers with a shared volume control, it's
anyway bound to the same DAC if needed, so this change shouldn't bring
any practical difference.
And, as a good bonus, we can cut off the whole code handling the bind
volume elements.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When 5.1 or more multiple speakers with found but not enough DACs are
available, it's better to bind such pins to the DACs of the primary
outputs with the same channels rather than binding to the first DAC
(i.e. the front channel). For the cases with two speaker pins, it's
rather regarded as front + bass combination, thus it's more practical
to still bind to the front, though.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
... like "Speaker Surround Playback Switch".
This fix had been already applied to patch_conexant.c but was
forgotten in other places, then migrated to hda_generic.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For codecs that have individual routes going through a loopback mixer
(like VIA codecs), we need to provide an explicit switch to choose
whether the output goes through mixer or directly from DAC.
This patch adds the check for such paths and creates "Loopback Mixing"
enum control when available.
It won't influence on codecs like Realtek or others where the loopback
mixer is connected independently from the primary output routes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The output paths including aamix should be parsed only for the first
output. The surround paths including aamix must be wrong, since it
would mix all streams, i.e. all channels would be mixed into a single
and multiplexed again.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Call the path activation for the digital input pin properly, not only
setting the pin control. Also add spec->digin_path for keeping the
path index.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of search for the path with the certain route at each time,
keep the path index for each output and loopback, and just use it when
referred.
In this implementation, the path index number begins with one, not
zero (although I've been writing in C over decades). It's just to
make the check for uninitialized values easier.
So far, the input paths aren't handled with indices yet, but still
picked up via snd_hda_get_nid_path() at each time.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When speakers are chosen as the the primary output during evaluation,
we did some tricks to assign the possible multi-io jacks with a
certain offset value to multi_out dacs. This was a workaround for the
case with multiple speakers like Acer Aspire. But this is quite ugly
at the same time and the resultant code is hard to understand. More
badly, it works wrongly for 2.1 speakers like Apple iMac91.
In this patch, instead of fiddling with the offset to multi_out dacs,
simply add a certain badness number if headphone(s) + multi-ios are
possible. This simplify the code a bit, and it's more robust.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If the requested path has been already added, return the existing path
instance instead of adding a duplicated instance.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the paths are created in map_singles(), we don't have to
re-create new paths in try_assign_dacs(). Just evaluate the badness
and skip to the next item.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Set path->active flag at the path creation time and let the paths
initialized according to the current path->active state in
set_output_and_unmute(). This allows to modify the active flag of
some output paths dynamically, e.g. switching the front output route
with or without aamix like patch_via.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
activate_amp() in the generic parser checks whether the given NID is
included in any active paths and skips it if found. This was a
workaround for avoiding disabling the widgets in the active paths when
one path is disabled, thus it shouldn't be applied to the case for
path activation. Due to this wrong check, some analog loopback paths
haven't been initialized correctly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Manage the connection list cache using linked lists instead of
snd_array, and revive snd_hda_get_conn_list() again, so that we don't
have to keep the expanded values locally.
This will reduce the stack usage by recursive call of
snd_hda_get_conn_index() or parse_nid_path() of the generic parser.
The list management doesn't include any mutex protection, thus the
caller needs to take care of race appropriately.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Yet another broken hardware workaround: there are hardware indicating
the inverted jack detection bit result.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the new flag, codec->inv_eapd, indicating that the EAPD
implementation is inverted.
There are always broken hardware in the world.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Similar like the implementation in patch_analog.c and patch_via.c,
the generic parser can provide the independent HP PCM stream now.
It's enabled when spec->indep_hp is set by the caller while parsing.
Currently no dynamic PCM switching as in patch_via.c is implemented
yet. The control returns -EBUSY when the value is changed during PCM
operations.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Allow the path including the loopback mixer widget in the primary
output channel as an alternative in the generic codec parser.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a better debug print code to show the new assigned paths in
generic parser. It appears only with CONFIG_SND_DEBUG_VERBOSE=y.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It's never used in the generic parser. It was there from the old
Realtek code, which has been dropped quite ago, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a PCM name string is generated from the chip name, it might
become strange like "CX20549 (Venice) Analog". In this patch, the
parser tries to drop the invalid words like "(Venice)" in the PCM name
string. Also, when the name string is given beforehand by the caller,
respect it and use it as is.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There were some old codes that look not stable enough, which was
derived from the old Realtek code. The initialization for primary
output in init_multi_out() needs to consider the case of shared DAC.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For preliminary works to migrate the generic parser for Conexant
codecs: the same function is ported to hda_generic.c.
But now it looks through the jack detect table so that it can cover
better.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a flag to indicate whether the vmaster mute hook enum is exposed
or not. Conexant codecs may want not to expose the control depending
on the model.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Old codecs like AD1986A tend to have long paths as they were just made
to be the way like AC97. The current max depth 5 can be too short for
such devices.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The access to a cache array element could be invalid outside the
mutex, so copy locally for the later references.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The dirty entry has to be checked at the beginning in the loop, not in
the inner loop for channels. This caused a regression that the right
channel isn't properly written.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The bound capture volume and switch controls use the cached amp
updates, but it's missing the flushing at the end.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The inverted dmic fix overwrites the right channel amp value, but it
would work only when the amp values have been already actually
written. Put snd_hda_codec_resume_amp() before the amp write for
flushing caches.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add an overflow check of CORB in HD-audio controller and codec drivers
so that flood of sequential writes would work properly.
In the controller side, add a check of CORB read-pointer to make
returning -EAGAIN when it's full. Meanwhile in the codec side, when
-EAGAIN error is received, it retries the write after flushing the
pending verbs (calling get_response() essentially does it).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These functions are supposed to be called at finishing the cached
sequential writes, so clear the flag properly for lazy developers who
often forget details.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When verbs or amps are actually written to the hardware, we can clear
dirty flag so that the later snd_hda_codec_resume_*() calls can skip
these verbs / amps.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit [2e9bf24: ALSA: hda_codec: Check for invalid zero
connections] trims the whole connection list when an invalid value is
reported by the hardware. But some codecs (at least AD1986A) may give
a zero NID in the middle of the connection list, so dropping the whole
list isn't good for such cases.
In this patch, as a workaround, allow a single zero NID in the read
connection list. If it hits zero twice, it's handled as an error, so
that we can avoid "too many connections" errors.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In general we prefer "Capture Source" to "Input Source".
The latter was chosen in many places just because "Capture Source"
label doesn't work well with the current alsa-lib mixer abstraction
when multiple instances are present. But when we know that there is a
single input-source element, we can safely choose "Capture Source"
label.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The next migration step is to use the common code in generic driver
for Realtek driver. This is no drastic change and there should be no
real functional changes, as the generic parser code comes from Realtek
driver originally.
As Realtek driver requires the generic parser code, it needs a
reverse-selection of CONFIG_SND_HDA_GENERIC kconfig.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These handlers are supposed to be called externally from the codec
drivers once when they need to handle own jack events.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When no controls are assigned in the parser (e.g. no analog path),
spec->kctls.list is still NULL. We need to check it before passing to
snd_hda_add_new_ctls().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In some cases, we want to manipulate the auto_pin_cfg table before
passing to snd_hda_gen_parse_auto_config() (e.g. Realtek SSID check
code fiddles with the headphone pin). Also passing ignore_pins just
for snd_hda_parse_pin_defcfg() isn't good.
In this patch, snd_hda_gen_parse_auto_config() is changed to receive
the auto_pin_cfg table to be parsed. The passed auto_pin_cfg table
must have been initialized (typically by calling
snd_hda_gen_parse_auto_config()) beforehand by the caller.
Also together with this change, spec->parse_flags is also removed.
Since this was referred only at the place calling
snd_hda_parse_pin_defcfg(), no longer needed to be kept in spec.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Finally the whole generic parser code in Realtek driver is moved into
hda_generic.c so that it can be used for generic codec driver.
The old dumb generic driver is replaced. Yay.
The future plan is to adapt this generic parser for other codecs,
i.e. the codec driver calls the exported functions in generic driver
but adds some codec-specific fixes and setups.
As of this commit, the complete driver code is still duplicated in
Realtek codec driver. The big code reduction will come from now on.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch extends the capability of the auto-mic feature.
Instead of limiting the automatic input-source selection only to the
mics (internal, external and dock mics), allow it for generic inputs,
e.g. switching between the rear line-in and the front mic.
The logic is to check the attribute and location of input pins, and
enable the automatic selection feature only if all such pins are in
different locations (e.g. internal, front, rear, etc) and line-in or
mic pins. That is, if multiple input pins are assigned to a single
location, the feature isn't enabled because we don't know the
priority.
(You may wonder why this restriction doesn't exist for the headphone
automute. The reason is that the output case is different from the
input: the input source is an exclusive selection while the output
can be multiplexed.)
Note that, for avoiding regressions, the line-in auto switching
feature isn't activated as default. It has to be set explicitly via
spec->line_in_auto_switch flag in a fixup code.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Put INPUT_PIN_ATTR_FRONT after INPUT_PIN_ATTR_REAR, and define
INPUT_PIN_ATTR_LAST to point to the last element.
This is a preliminary work for cleaning up Realtek auto-mic parser.
In the auto-mic implementation, the front panel is preferred over the
rear panel. By arranging the attr definitions like in this commit, we
can simply use sort() for figuring out the priority order.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The previous commit passed an utterly wrong value for checking the
split inv dmic pin. This patch fixes it and also tries to remove
inv_dmic_split_idx field.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since the fixup code is used commonly, it's worth to move it to the
common place, struct hda_codec, instead of keeping in hda_gen_spec.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To make the parser more generic, a few codes to handle the inverted
stereo dmic in a way Conexant parser does is added in this patch.
The caller should set spec->inv_dmic_split flag appropriately.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
So far we create only "Capture Volume" and "Capture Switch" controls
for binding all possible amps, but we'd prefer creating individual
capture volume and switch controls per input in some cases
(e.g. conexant parser does it).
Add a new flag, spec->multi_cap_vol, to follow that policy.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
