This commit is essentially a rewrite of "drm/i915: Check pixel format
for fbc" from Ville Syrjälä. The idea is the same, but the code is
different due to all the changes that happened since his original
patch. So any bugs are due to my bad rewrite.
v2:
- Drop the alpha formats (Ville).
v3:
- Drop the stale comment (Ville).
Testcases: igt/kms_frontbuffer_tracking/*fbc*-${format_name}-draw-*
Credits-to: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BSpec says we shouldn't enable FBC on HSW/BDW when the pipe pixel rate
exceeds 95% of the core display clock.
v2:
- HSW also needs the WA (Ville).
- Add the WA name (Ville).
- Use the current cdclk (Ville).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The FBC hardware for these platforms doesn't have access to the
bios_reserved range, so it always assumes the maximum (8mb) is used.
So avoid this range while allocating.
This solves a bunch of FIFO underruns that happen if you end up
putting the CFB in that memory range. On my machine, with 32mb of
stolen, I need a 2560x1440 mode for that.
Testcase: igt/kms_frontbuffer_tracking/fbc-* (given the right setup)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Don't allow FBC for cases where the spec says we can't FBC.
v2:
- Just WARN_ON() the strides that should have been caught earlier
(Daniel)
- Make it a new function since I expect this to grow more.
v3:
- Document which IGT test is exercised by this.
v4:
- Implement the restrictions for gens 2-6 too (Ville).
- Fix off-by-one mistake (Ville).
Testcase: igt/kms_frontbuffer_tracking/fbc-badstride
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It will be usefull to specify w/a that affects only SKL GT3 and GT4.
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Modified HAS_CSR macro defination which earlier only supported
for skl, now added support for BXT.
v1: Initial version.
v2: Instaed of skylake/broxton check added gen9 check alone based
on review comment from Sunil.
Cc: Vetter, Daniel <daniel.vetter@intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Shared frontbuffer bits are causing warnings when same FB is displayed
in another plane without clearing the bits from previous plane.
v2: Removing coversion of fb bits to 64 bit as it is not needed for now. (Daniel)
Change-Id: Ic2df80747f314b82afd22f8326297c57d1e652c6
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Kumar, Mahesh <mahesh1.kumar@intel.com>
[danvet: Drop INTEL_FRONTBUFFER_SPRITE_MASK since unused.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Extend init/init_hw split to context init.
- Move context initialisation in to i915_gem_init_hw
- Move one off initialisation for render ring to
i915_gem_validate_context
- Move default context initialisation to logical_ring_init
Rename intel_lr_context_deferred_create to
intel_lr_context_deferred_alloc, to reflect reduced functionality &
alloc/init split.
This patch is intended to split out the allocation of resources &
initialisation to allow easier reuse of code for resume/gpu reset.
v2: Removed function ptr wrapping of do_switch_context (Daniel Vetter)
Left ->init_context int intel_lr_context_deferred_alloc
(Daniel Vetter)
Remove unnecessary init flag & ring type test. (Daniel Vetter)
Improve commit message (Daniel Vetter)
v3: On init/reinit, set the hw next sequence number to the sw next
sequence number. This is set to 1 at driver load time. This prevents
the seqno being reset on reinit (Chris Wilson)
v4: Set seqno back to ~0 - 0x1000 at start-of-day, and increment by 0x100
on reset.
This makes it obvious which bbs are which after a reset. (David Gordon
& John Harrison)
Rebase.
v5: Rebase. Fixed rebase breakage. Put context pinning in separate
function. Removed code churn. (Thomas Daniel)
v6: Cleanup up issues introduced in v2 & v5 (Thomas Daniel)
Issue: VIZ-4798
Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: John Harrison <john.c.harrison@intel.com>
Cc: David Gordon <david.s.gordon@intel.com>
Cc: Thomas Daniel <thomas.daniel@intel.com>
Reviewed-by: Thomas Daniel <thomas.daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is done as a separate commit, to make it easier to revert
when things break.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull drm fixes from Dave Airlie:
"Just a bunch of fixes to squeeze in before -rc1:
- three nouveau regression fixes
- one qxl regression fix
- a bunch of i915 fixes
... and some core displayport/atomic fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau/device: enable c800 quirk for tecra w50
drm/nouveau/clk/gt215: Unbreak engine pausing for GT21x/MCP7x
drm/nouveau/gr/nv04: fix big endian setting on gr context
drm/qxl: validate monitors config modes
drm/i915: Allow DSI dual link to be configured on any pipe
drm/i915: Don't try to use DDR DVFS on CHV when disabled in the BIOS
drm/i915: Fix CSR MMIO address check
drm/i915: Limit the number of loops for reading a split 64bit register
drm/i915: Fix broken mst get_hw_state.
drm/i915: Pass hpd_status_i915[] to intel_get_hpd_pins() in pre-g4x
uapi/drm/i915_drm.h: fix userspace compilation.
drm/i915: Always mark the object as dirty when used by the GPU
drm/dp: Add dp_aux_i2c_speed_khz module param to set the assume i2c bus speed
drm/dp: Adjust i2c-over-aux retry count based on message size and i2c bus speed
drm/dp: Define AUX_RETRY_INTERVAL as 500 us
drm/atomic: Fix bookkeeping with TEST_ONLY, v3.
If one disables DDR DVFS in the BIOS, Punit will apparently ignores
all DDR DVFS request. Currently we assume that DDR DVFS is always
operational, which leads to errors in dmesg when the DDR DVFS requests
time out.
Fix the problem by gently prodding Punit during driver load to find out
whether it will respond to DDR DVFS requests. If the request times out,
we assume that DDR DVFS has been permanenly disabled in the BIOS and
no longer perster the Punit about it.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91629
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Tested-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
In I915_READ64_2x32 we attempt to read a 64bit register using 2 32bit
reads. Due to the nature of the registers we try to read in this manner,
they may increment between the two instruction (e.g. a timestamp
counter). To keep the result accurate, we repeat the read if we detect
an overflow (i.e. the upper value varies). However, some hardware is just
plain flaky and may endless loop as the the upper 32bits are not stable.
Just give up after a couple of tries and report whatever we read last.
v2: Use the most recent values when erring out on an unstable register.
Reported-by: russianneuromancer@ya.ru
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91906
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Normally we determine the backlight PWM modulation frequency (which we
also use as backlight max value) from the backlight registers at module
load time, expecting the registers have been initialized by the BIOS. If
this is not the case, we fail.
The VBT contains the backlight modulation frequency in Hz. Add platform
specific functions to convert the frequency in Hz to backlight PWM
modulation frequency, and use them to initialize the backlight when the
registers are not initialized by the BIOS.
v2: Fix SPT and VLV. Thanks to Clint for the VLV code.
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull drm updates from Dave Airlie:
"This is the main pull request for the drm for 4.3. Nouveau is
probably the biggest amount of changes in here, since it missed 4.2.
Highlights below, along with the usual bunch of fixes.
All stuff outside drm should have applicable acks.
Highlights:
- new drivers:
freescale dcu kms driver
- core:
more atomic fixes
disable some dri1 interfaces on kms drivers
drop fb panic handling, this was just getting more broken, as more locking was required.
new core fbdev Kconfig support - instead of each driver enable/disabling it
struct_mutex cleanups
- panel:
more new panels
cleanup Kconfig
- i915:
Skylake support enabled by default
legacy modesetting using atomic infrastructure
Skylake fixes
GEN9 workarounds
- amdgpu:
Fiji support
CGS support for amdgpu
Initial GPU scheduler - off by default
Lots of bug fixes and optimisations.
- radeon:
DP fixes
misc fixes
- amdkfd:
Add Carrizo support for amdkfd using amdgpu.
- nouveau:
long pending cleanup to complete driver,
fully bisectable which makes it larger,
perfmon work
more reclocking improvements
maxwell displayport fixes
- vmwgfx:
new DX device support, supports OpenGL 3.3
screen targets support
- mgag200:
G200eW support
G200e new revision support
- msm:
dragonboard 410c support, msm8x94 support, msm8x74v1 support
yuv format support
dma plane support
mdp5 rotation
initial hdcp
- sti:
atomic support
- exynos:
lots of cleanups
atomic modesetting/pageflipping support
render node support
- tegra:
tegra210 support (dc, dsi, dp/hdmi)
dpms with atomic modesetting support
- atmel:
support for 3 more atmel SoCs
new input formats, PRIME support.
- dwhdmi:
preparing to add audio support
- rockchip:
yuv plane support"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (1369 commits)
drm/amdgpu: rename gmc_v8_0_init_compute_vmid
drm/amdgpu: fix vce3 instance handling
drm/amdgpu: remove ib test for the second VCE Ring
drm/amdgpu: properly enable VM fault interrupts
drm/amdgpu: fix warning in scheduler
drm/amdgpu: fix buffer placement under memory pressure
drm/amdgpu/cz: fix cz_dpm_update_low_memory_pstate logic
drm/amdgpu: fix typo in dce11 watermark setup
drm/amdgpu: fix typo in dce10 watermark setup
drm/amdgpu: use top down allocation for non-CPU accessible vram
drm/amdgpu: be explicit about cpu vram access for driver BOs (v2)
drm/amdgpu: set MEC doorbell range for Fiji
drm/amdgpu: implement burst NOP for SDMA
drm/amdgpu: add insert_nop ring func and default implementation
drm/amdgpu: add amdgpu_get_sdma_instance helper function
drm/amdgpu: add AMDGPU_MAX_SDMA_INSTANCES
drm/amdgpu: add burst_nop flag for sdma
drm/amdgpu: add count field for the SDMA NOP packet v2
drm/amdgpu: use PT for VM sync on unmap
drm/amdgpu: make wait_event uninterruptible in push_job
...
Make LPT:LP checks look neater by wrapping the details in a
new HAS_PCH_LPT_LP() macro.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge -fixes since there's more DDI-E related cleanups on top of
the pile of -fixes for skl that just landed for 4.3.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i914/intel_dp.c
drivers/gpu/drm/i915/intel_lrc.c
Conflicts are all fairly harmless adjacent line stuff.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
When the audio codec is enabled or disabled, notify the audio driver.
This will enable the audio driver to get the notification at all times
(even when audio is in different powersave states).
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a common function to return "yes" or "no" string based on the
argument, and drop the local versions of it.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The driver doesn't support UMS any more, so set DRIVER_MODESET by default,
remove the legacy s/r callbacks, and rename the s/r functions to make it more clear
they're only in use by switcheroo now.
Also remove an obsolete comment about atomic. Normal updates are supported only
async updates aren't yet.
v2: Don't unconditionally set DRIVER_ATOMIC, we're not yet there.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From B spec, DDI_E port belong to PowerWell 2, but
DDI_E share the powerwell_req/staus register bit with
DDI_A which belong to DDI_A_E_POWER_WELL.
In order to communicate with the connector on DDI-E, both
DDI_A_E_POWER_WELL and POWER_WELL_2 must be enabled.
Currently intel_dp_power_get(DDI_E) only enable
DDI_A_E_POWER_WELL, this patch will not only enable
DDI_a_E_POWER_WELL but also enable POWER_WELL_2.
This patch also fix the DDI-E hotplug function.
Signed-off-by: Xiong Zhang <xiong.y.zhang@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
DDI-E doesn't have the correspondent GMBUS pin.
We rely on VBT to tell us which one it being used instead.
The DVI/HDMI on shared port couldn't exist.
This patch isn't tested without hardware wchich has HDMI
on DDI-E.
v2: fix trailing whitespace
v3: MISSING_CASE take place of BUG()
Signed-off-by: Xiong Zhang <xiong.y.zhang@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This partially reverts commit 74c090b1bd.
The DRIVER_ATOMIC cap cannot yet be exported because i915 lacks async
support.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Store max dotclock into dev_priv structure so we are able
to filter out the modes that are not supported by our
platforms.
V2:
- limit the max dot clock frequency to max CD clock frequency
for the gen9 and above
- limit the max dot clock frequency to 90% of the max CD clock
frequency for the older gens
- for Cherryview the max dot clock frequency is limited to 95%
of the max CD clock frequency
- for gen2 and gen3 the max dot clock limit is set to 90% of the
2X max CD clock frequency
V3:
- max_dotclk variable renamed as max_dotclk_freq in i915_drv.h
- in intel_compute_max_dotclk() the rounding method changed from
round up to round down when computing max dotclock
V4:
- Haswell and Broadwell supports now dot clocks up to max CD clock
frequency
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The current versions of these two macros don't work correctly if the
argument expression happens to contain a modulo operator (%) -- when
stringified, it gets interpreted as a printf formatting character!
With a specifically crafted parameter, this could probably cause a
kernel OOPS; consider WARN_ON(p%s) or WARN_ON(f %*pEp).
Instead, we should use an explicit "%s" format, with the stringified
expression as the coresponding literal-string argument.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: fix one error found by checkpath.pl
v3: Add one ignored break for switch-case. DDI-E hotplug
function doesn't work after updating drm-intel tree,
I checked the code and found this missing which isn't
the root cause for broke DDI-E hp. The broken
DDI-E hp function is fixed by "Adding DDI_E power
well domain".
Signed-off-by: Xiong Zhang <xiong.y.zhang@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Tested-by: Timo Aaltonen <timo.aaltonen@canonical.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Bunch more fixes for 4.3, most of it skl fallout. It's not quite all yet,
there's still a few more patches pending to enable DDI-E correctly on skl.
Also included the dpms atomic work from Maarten since atomic is just a
pain and not including would cause piles of conflicts right from the
start.
* tag 'drm-intel-next-fixes-2015-08-16' of git://anongit.freedesktop.org/drm-intel: (67 commits)
drm/i915: Per-DDI I_boost override
drm/i915/skl: WaIgnoreDDIAStrap is forever, always init DDI A
drm/i915: fix checksum write for automated test reply
drm/i915: Contain the WA_REG macro
drm/i915: Remove the failed context from the fpriv->context_idr
drm/i915: Report IOMMU enabled status for GPU hangs
drm/i915: Check idle to active before processing CSQ
drm/i915: Set alternate aux for DDI-E
drm/i915: Set power domain for DDI-E
drm/i915: fix stolen bios_reserved checks
drm/i915: Use masked write for Context Status Buffer Pointer
drm/i915/skl WaDisableSbeCacheDispatchPortSharing
drm/i915: Spam less on dp aux send/receive problems
drm/i915: Handle return value in intel_pin_and_fence_fb_obj, v2.
drm/i915: Only update mode related state if a modeset happened.
drm/i915: Remove connectors_active.
drm/i915: Remove connectors_active from intel_dp.c, v2.
drm/i915: Remove connectors_active from sanitization, v2.
drm/i915: Get rid of dpms handling.
drm/i915: Make crtc checking use the atomic state, v2.
...
This fetches the required firmware image from the filesystem,
then loads it into the GuC's memory via a dedicated DMA engine.
This patch is derived from GuC loading work originally done by
Vinit Azad and Ben Widawsky.
v2:
Various improvements per review comments by Chris Wilson
v3:
Removed 'wait' parameter to intel_guc_ucode_load() as firmware
prefetch is no longer supported in the common firmware loader,
per Daniel Vetter's request.
Firmware checker callback fn now returns errno rather than bool.
v4:
Squash uC-independent code into GuC-specifc loader [Daniel Vetter]
Don't keep the driver working (by falling back to execlist mode)
if GuC firmware loading fails [Daniel Vetter]
v5:
Clarify WOPCM-related #defines [Tom O'Rourke]
Delete obsolete code no longer required with current h/w & f/w
[Tom O'Rourke]
Move the call to intel_guc_ucode_init() later, so that it can
allocate GEM objects, and have it fetch the firmware; then
intel_guc_ucode_load() doesn't need to fetch it later.
[Daniel Vetter].
v6:
Update comment describing intel_guc_ucode_load() [Tom O'Rourke]
Issue: VIZ-4884
Signed-off-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Similar to commit c44ef60e43 ("drm/i915/gtt:
Allow >= 4GB sizes for vm"), i915_gem_obj_offset and i915_gem_obj_ggtt_offset
return an unsigned long, which in only 4-bytes long in 32-bit kernels.
Change return type (and other related offset variables) to u64.
Since Global GTT is always limited to 4GB, this change would not be required
in i915_gem_obj_ggtt_offset, but this is done for consistency.
v2: Remove unnecessary offset variable in do_pin, as we already have
vma->node.start (Chris).
Update GGTT offset too (Tvrtko).
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Otherwise it can overflow in 48-bit mode, and cause an incorrect
exec_start.
Before commit 5f19e2bffa ("drm/i915: Merged
the many do_execbuf() parameters into a structure"), it was already an u64.
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: For semaphore errors, object is mapped to GGTT and offset will not
be > 4GB, print only lower 32-bits (Akash)
v3: Print gtt_offset in groups of 32-bit (Chris)
Cc: Akash Goel <akash.goel@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Introduces the Page Map Level 4 (PML4), ie. the new top level structure
of the page tables.
To facilitate testing, 48b mode will be available on Broadwell and
GEN9+, when i915.enable_ppgtt = 3.
v2: Remove unnecessary CONFIG_X86_64 checks, ppgtt code is already
32/64-bit safe (Chris).
v3: Add goto free_scratch in temp 48-bit mode init code (Akash).
v4: kfree the pdp until the 4lvl alloc/free patch (Akash).
v5: Postpone 48-bit code in sanitize_enable_ppgtt (Akash).
v6: Keep _insert_pte_entries changes outside this patch (Akash).
Cc: Akash Goel <akash.goel@intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
An OEM may request increased I_boost beyond the recommended values
by specifying an I_boost value to be applied to all swing entries for
a port. These override values are specified in VBT.
v2: rebase and remove unused iboost_bit variable
Issue: VIZ-5676
Signed-off-by: Antti Koskipaa <antti.koskipaa@linux.intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge drm-intel-fixes because a bunch of atomic patch backporting
we had to do lead to horrible conflicts.
Conflicts:
drivers/gpu/drm/drm_crtc.c
Just a bit of context conflict between -next and -fixes.
drivers/gpu/drm/i915/intel_atomic.c
drivers/gpu/drm/i915/intel_display.c
Atomic conflicts, always pick the code from -next.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The IOMMU for Intel graphics has historically had many issues resulting
in random GPU hangs. Lets include its status when capturing the GPU hang
error state for post-mortem analysis.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is no correspondent Aux channel for DDI-E.
So we need to rely on VBT to let us know witch one
is being used instead.
v2: Removing some trailing spaces and giving proper
credit to Xiong that added a nice way to avoid port
conflicts by setting supports_dp = 0 when using
equivalent aux for DDI-E.
Credits-to: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of our own duplicated one. This fixes a bug in the driver
unload code if DRM_FBDEV_EMULATION=n but DRM_I915_FBDEV=y because we
try to unregister the nonexistent fbdev drm_framebuffer.
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reported-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch contains the changes to remove the byte
swapping logic introduced with old dmc firmware.
While debugging PC10 entry issue for skylake found
with latest dmc firmware version 1.18 without byte
swapping dmc is working fine and able to enter PC10.
Note that apparently this was changed with dmc version 1.0 and earlier
ones indeed are byteswapped like this ...
v1: Initial version.
v2: Corrected firmware size during memcpy(). (Suggested by Sunil)
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Vathsala Nagaraju <vathsala.nagaraju@intel.com>
Reviewed-by: A.Sunil Kamath <sunil.kamath@intel.com>
[danvet: Add note that this only holds for released dmc firmware.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
First, an introduction. We currently have two types of GTT mmaps: the
"normal" old mmap, and the WC mmap. For frontbuffer-related features
that have automatic hardware tracking, only the non-WC mmap writes are
detected by the hardware. Since inside the Kernel both are treated as
ORIGIN_GTT, any features ignoring ORIGIN_GTT because of the hardware
tracking are destined to fail.
One of the special rules defined for the WC mmaps is that the user
should call the dirtyfb IOCTL after he is done using the pointers, so
that results in an intel_fb_obj_flush() call. The problem is that the
dirtyfb is passing ORIGIN_GTT, so it is being ignored by FBC - even
though the hardware tracking is not detecing the WC mmap operations.
So in order to fix that without having to give up the automatic
hardware tracking for GTT mmaps we transform the flush operation from
dirtyfb into a special operation: ORIGIN_DIRTYFB.
This commit fixes all the kms_frontbuffer_tracking subtests that
contain "fbc" and "mmap-wc" in their names and are currently failing
(for a total of 16 subtests).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since we may conceivably encounter situations where the upper part of the
64bit register changes between reads, for example when a timestamp
counter overflows, change the WARN into a retry loop.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Remove the leftovers, yay!
AGP for i915 kms died long ago with
commit 3bb6ce6686
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Nov 13 22:14:16 2013 +0100
drm/i915: Kill legeacy AGP for gen3 kms
and with ums now gone to there's really no users any more.
Note that device_is_agp is only called when DRIVER_USE_AGP is set and
since we've unconditionally cleared that since a while there are
really no users left for i915_driver_device_is_agp.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
It fits more with the low-level fence code, and this move leaves only
the userspace tiling ioctl handling in i915_gem_tiling.c.
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
No code changes, just moving all the fence related code into a
separate file (and avoiding a bunch of forward declarations while at
it).
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Currently HPD_PORT_A is used as an alias for HPD_NONE to mean that the
given port doesn't support long/short HPD pulse detection. SDVO and CRT
ports are like this and for these ports we only want to know whether an
hot plug event was detected on the corresponding pin. Since at least on
BXT we need long/short pulse detection on PORT A as well (added by the
next patch) remove this aliasing of HPD_PORT_A/HPD_NONE and let the
return value of intel_hpd_pin_to_port() show whether long/short pulse
detection is supported on the passed in pin.
No functional change.
v2:
- rebase on top of -nightly (Daniel)
- make the check for intel_hpd_pin_to_port() return value more readable
(Sivakumar)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Two new module parameters: "enable_guc_submission" which will turn
on submission of batchbuffers via the GuC (when implemented), and
"guc_log_level" which controls the level of debugging logged by the
GuC and captured by the host.
Signed-off-by: Alex Dai <yu.dai@intel.com>
v4:
Mark "enable_guc_submission" unsafe [Daniel Vetter]
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
i915_gem_object_create_from_data() is a generic function to save data
from a plain linear buffer in a new pageable gem object that can later
be accessed by the CPU and/or GPU.
We will need this for the microcontroller firmware loading support code.
Derived from i915_gem_object_write(), originally by Alex Dai
v2:
Change of function: now allocates & fills a new object, rather than
writing to an existing object
New name courtesy of Chris Wilson
Explicit domain-setting and other improvements per review comments
by Chris Wilson & Daniel Vetter
v4:
Rebased
Issue: VIZ-4884
Signed-off-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge fixes since it's getting out of hand again with the massive
split due to atomic between -next and 4.2-rc. All the bugfixes in
4.2-rc are addressed already (by converting more towards atomic
instead of minimal duct-tape) so just always pick the version in next
for the conflicts in modeset code.
All the other conflicts are just adjacent lines changed.
Conflicts:
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/i915/i915_gem_gtt.c
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_drv.h
drivers/gpu/drm/i915/intel_ringbuffer.h
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Huzzah! \o/
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Updated the HAS_CORE_RING_FREQ macro to add the broxton check,
so as to disallow the programming & read of ring frequency
table for it.
Issue: VIZ-5144
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added a new HAS_CORE_RING_FREQ macro, currently used in
gen6_update_ring_freq & i915_ring_freq_table debugfs function.
The programming & read of ring frequency table is needed for newer
GEN(>=6) platforms, except VLV/CHV.
Issue: VIZ-5144
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of all the ad-hoc updating, duplicate the old state first
before reading out the hw state, then restore it.
intel_display_resume is a new function that duplicates the sw state,
then reads out the hw state, and commits the old state.
intel_display_setup_hw_state now only reads out the atomic state.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90396
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After the previous patch this flag will check always clear, as it's
never set for shmem backed and userptr objects, so we can remove it.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Yeah this isn't really fixes but it's a nice cleanup to
clarify the code but not really worth the hassle of backmerging. So
just add to -fixes, we're still early in -rc.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This broken code was introduced in
commit aa7471d228
Author: Jani Nikula <jani.nikula@intel.com>
Date: Wed Apr 1 11:15:21 2015 +0300
drm/i915: add i915 specific connector debugfs file for DPCD
v2: Drop hunk that accidentally crept in.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Bob Paauwe <bob.j.paauwe@intel.com>
Cc: François Valenduc <francoisvalenduc@gmail.com>
Reported-by: François Valenduc <francoisvalenduc@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The poor in_dbg_master() check was the only one without a reason
string. Give it a reason string so it won't feel excluded.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is all internal i915.ko work, let's start using intel_crtc for
everything.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because the cool kids use dev_priv and FBC wants to be cool too.
We've been historically using struct drm_device on the FBC function
arguments, but we only really need it for intel_vgpu_active(): we can
use dev_priv everywhere else. So let's fully switch to dev_priv since
I'm getting tired of adding "struct drm_device *dev = dev_priv->dev"
everywhere.
If I get a NACK here I'll propose the opposite: convert all the
functions that currently take dev_priv to take dev.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because it makes more sense there, IMHO.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After the register save/restore code is gone there's just one user
left and it just obfuscates that one. Remove it.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since that's really what we want to test for. Note remove the gen5
case doesn't change anything: In intel_setup_outputs ilk is handled
already in the HAS_PCH_SPLIT case, and the register save/restore code
touches registers which simply doesn't exist anymore at all.
v2: Drop UMS parts.
v3: Update commit message to reflect that the reg save/restore code is
gone (Ville).
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make sure we're not going to have weird races in really weird cases
where a lot of different CRTCs are doing rendering and modesets at the
same time.
With this change and the stolen_lock from the previous patch, we can
start removing the struct_mutex locking we have around FBC in the next
patches.
v2:
- Rebase (6 months later)
- Also lock debugfs and stolen.
v3:
- Don't lock a single value read (Chris).
- Replace lockdep assertions with WARNs (Daniel).
- Improve commit message.
- Don't forget intel_pre_plane_update() locking.
v4:
- Don't remove struct_mutex at intel_pre_plane_update() (Chris).
- Add comment regarding locking dependencies (Chris).
- Rebase after the stolen code rework.
- Rebase again after drm-intel-nightly changes.
v5:
- Rebase after the new stolen_lock patch.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v4)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Which should protect dev_priv->mm.stolen usage. This will allow us to
simplify the relationship between stolen memory, FBC and struct_mutex.
v2:
- Rebase after the stolen_remove_node() dev_priv patch move.
- I realized that after we fixed a few things related to the FBC CFB
size checks, we're not reallocating the CFB anymore with FBC
enabled, so we can just move all the locking to i915_gem_stolen.c
and stop worrying about freezing all the stolen alocations while
freeing/rellocating the CFB. This allows us to fix the "Too
coarse" observation from Chris.
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the abstractions created by the last patch, we can move this code
and the only thing inside intel_fbc.c that knows about dev_priv->mm is
the code that reads stolen_base.
We also had to move a call to i915_gem_stolen_cleanup_compression()
- now called intel_fbc_cleanup_cfb() - outside i915_gem_stolen.c.
v2:
- Rebase after the remove_node() changes on the previous patch.
Requested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We want to move the FBC code out of i915_gem_stolen.c, but that code
directly adds/removes stolen memory nodes. Let's create this
abstraction, so i915_gme_stolen.c is still in control of all the
stolen memory handling. The abstraction will also allow us to add
locking assertions later.
v2:
- Add dev_priv as remove_node() argument since we'll need it later
(Chris).
Requested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ensures that the batch buffer is executed by the resource streamer.
And will let userspace know whether Resource Streamer is supported in
the kernel.
v2: Don't skip 1<<15 for the exec flags (Jani Nikula)
v3: Use HAS_RESOURCE_STREAMER macro for execbuf validation (Chris Wilson)
(from getparam patch)
v2: Update I915_PARAM_HAS_RESOURCE_STREAMER so it's after
I915_PARAM_HAS_GPU_RESET.
v3: Only advertise RS support for hardware that supports it.
v4: Add HAS_RESOURCE_STREAMER() macro (Chris)
Testcase: igt/gem_exec_params
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Kenneth Graunke <kenneth@whitecape.org>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Abdiel Janulgue <abdiel.janulgue@linux.intel.com>
[danvet: squash in getparam patch since it'd break bisect, suggested
by Chris.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Although we have a fixed setting for the PLL9 and EBB4 registers, it
still makes sense to check them together with the rest of PLL registers.
While at it also remove a redundant comment about 10 bit clock enabling.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch adds support for 0.85V VccIO on Skylake Y,
separate buffer translation tables for Skylake U,
and support for I_boost for the entries that needs this.
Changes in v2:
* Refactored the code a bit to move all DDI signal level setup to
intel_ddi.c
Issue: VIZ-5677
Signed-off-by: David Weinehall <david.weinehall@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
[danvet: Apply style polish checkpatch suggested.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Turns out the VLV/CHV system agent doesn't understand memory
latencies, so trying to rely on the PND deadline mechanism is not
going to fly especially when DDR DVFS is enabled. Currently we try to
avoid the problems by lying to the system agent about the deadlines
and setting the FIFO watermarks to 8 cachelines. This however leads to
bad memory self refresh residency.
So in order to satosfy everyone we'll just give up on the deadline
scheme and program the watermarks old school based on the worst case
memory latency.
I've modelled this a bit on the ILK+ approach where we compute multiple
sets of watermarks for each pipe (PM2,PM5,DDR DVFS) and when merge thet
appropriate one later with the watermarks from other pipes. There isn't
too much to merge actually since each pipe has a totally independent
FIFO (well apart from the mess with the partially shared DSPARB
registers), but still decopuling the pipes from each other seems like a
good idea.
Eventually we'll want to perform the watermark update in two phases
around the plane update to avoid underruns due to the single buffered
watermark registers. But that's still in limbo for ILK+ too, so I've not
gone that far yet for VLV/CHV either.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Read out the current watermark settings from the hardware at driver init
time. This will allow us to compare the newly calculated values against
the currrent ones and potentially avoid needless WM updates.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the new DRRS code it kinda sticks out, and we never managed to
get this to work well enough without causing issues. Time to wave
goodbye.
I've decided to keep the logic for programming the reduced clocks
intact, but everything else is gone. If anyone ever wants to resurrect
this we need to redo it all anyway on top of the frontbuffer tracking.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As there is no OLR to check, the check_olr() function is now a no-op and can be
removed.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In _i915_add_request(), the request is associated with a userland client.
Specifically it is linked to the 'file' structure and the current user process
is recorded. One problem here is that the current user process is not
necessarily the same as when the request was submitted to the driver. This is
especially true when the GPU scheduler arrives and decouples driver submission
from hardware submission. Note also that it is only in the case where the add
request comes from an execbuff call that there is a client to associate. Any
other add request call is kernel only so does not need to do it.
This patch moves the client association into a separate function. This is then
called from the execbuffer code path itself at a sensible time. It also removes
the now redundant 'file' pointer from the add request parameter list.
An extra cleanup of the client association is also added to the request clean up
code for the eventuality where the request is killed after association but
before being submitted (e.g. due to out of memory error somewhere). Once the
submission has happened, the request is on the request list and the regular
request list removal will clear the association. Note that this still needs to
happen at this point in time because the request might be kept floating around
much longer (due to someone holding a reference count) and the client should not
be worrying about this request after it has been retired.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Converted i915_gem_l3_remap() to take a request structure instead of a ring.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that everything above has been converted to use request structures, it is
possible to update the lower level move_to_active() functions to be request
based as well.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that all callers of i915_add_request() have a request pointer to hand, it is
possible to update the add request function to take a request pointer rather
than pulling it out of the OLR.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Updated the display page flip code to do explicit request creation and
submission rather than relying on the OLR and just hoping that the request
actually gets submitted at some random point.
The sequence is now to create a request, queue the work to the ring, assign the
known request to the flip queue work item then actually submit the work and post
the request.
Note that every single flip function used to finish with
'__intel_ring_advance(ring);'. However, immediately after they return there is
now an add request call which will do the advance anyway. Thus the many
duplicate advance calls have been removed.
v2: Updated commit message with comment about advance removal.
v3: The request can now be allocated by the _sync() code earlier on. Thus the
page flip path does not necessarily need to allocate a new request, it may be
able to re-use one.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The plan is to pass requests around as the basic submission tracking structure
rather than rings and contexts. This patch updates the i915_gem_object_sync()
code path.
v2: Much more complex patch to share a single request between the sync and the
page flip. The _sync() function now supports lazy allocation of the request
structure. That is, if one is passed in then that will be used. If one is not,
then a request will be allocated and passed back out. Note that the _sync() code
does not necessarily require a request. Thus one will only be created until
certain situations. The reason the lazy allocation must be done within the
_sync() code itself is because the decision to need one or not is not really
something that code above can second guess (except in the case where one is
definitely not required because no ring is passed in).
The call chains above _sync() now support passing a request through which most
callers passing in NULL and assuming that no request will be required (because
they also pass in NULL for the ring and therefore can't be generating any ring
code).
The exeception is intel_crtc_page_flip() which now supports having a request
returned from _sync(). If one is, then that request is shared by the page flip
(if the page flip is of a type to need a request). If _sync() does not generate
a request but the page flip does need one, then the page flip path will create
its own request.
v3: Updated comment description to be clearer about 'to_req' parameter (Tomas
Elf review request). Rebased onto newer tree that significantly changed the
synchronisation code.
v4: Updated comments from review feedback (Tomas Elf)
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that the request is guaranteed to specify the context, it is possible to
update the context switch code to use requests rather than ring and context
pairs. This patch updates i915_switch_context() accordingly.
Also removed the warning that the request's context must match the last context
switch's context. As the context switch now gets the context object from the
request structure, there is no longer any scope for the two to become out of
step.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The final step in removing the OLR from i915_gem_init_hw() is to pass the newly
allocated request structure in to each step rather than passing a ring
structure. This patch updates both i915_ppgtt_init_ring() and
i915_gem_context_enable() to take request pointers.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that a single per ring loop is being done for all the different
intialisation steps in i915_gem_init_hw(), it is possible to add proper request
management as well. The last remaining issue is that the context enable call
eventually ends up within *_render_state_init() and this does its own private
_i915_add_request() call.
This patch adds explicit request creation and submission to the top level loop
and removes the add_request() from deep within the sub-functions.
v2: Updated for removal of batch_obj from add_request call in previous patch.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The start of day context initialisation code in i915_gem_context_enable() loops
over each ring and calls the legacy switch context or the execlist init context
code as appropriate.
This patch moves the ring looping out of that function in to the top level
caller i915_gem_init_hw(). This means the a single pass can be made over all
rings doing the PPGTT, L3 remap and context initialisation of each ring
altogether.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In order to explcitly track all GPU work (and completely remove the outstanding
lazy request), it is necessary to add extra i915_add_request() calls to various
places. Some of these do not need the implicit cache flush done as part of the
standard batch buffer submission process.
This patch adds a flag to _add_request() to specify whether the flush is
required or not.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The plan is to pass requests around as the basic submission tracking structure
rather than rings and contexts. This patch updates the
execbuffer_move_to_active() code path.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rather than just having a local request variable in the execbuff code, the
request pointer is now stored in the execbuff params structure. Also added
explicit cleanup of the request (plus wiping the OLR to match) in the error
case. This means that the execbuff code is no longer dependent upon the OLR
keeping track of the request so as to not leak it when things do go wrong. Note
that in the success case, the i915_add_request() at the end of the submission
function will tidy up the request and clear the OLR.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The alloc_request() function does not actually return the newly allocated
request. Instead, it must be pulled from ring->outstanding_lazy_request. This
patch fixes this so that code can create a request and start using it knowing
exactly which request it actually owns.
v2: Updated for new i915_gem_request_alloc() scheme.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Shrunk the parameter list of i915_gem_execbuffer_retire_commands() to a single
structure as everything it requires is available in the execbuff_params object.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The do_execbuf() function takes quite a few parameters. The actual set of
parameters is going to change with the conversion to passing requests around.
Further, it is due to grow massively with the arrival of the GPU scheduler.
This patch simplifies the prototype by passing a parameter structure instead.
Changing the parameter set in the future is then simply a matter of
adding/removing items to the structure.
Note that the structure does not contain absolutely everything that is passed
in. This is because the intention is to use this structure more extensively
later in this patch series and more especially in the GPU scheduler that is
coming soon. The latter requires hanging on to the structure as the final
hardware submission can be delayed until long after the execbuf IOCTL has
returned to user land. Thus it is unsafe to put anything in the structure that
is local to the IOCTL call itself - such as the 'args' parameter. All entries
must be copies of data or pointers to structures that are reference counted in
some way and guaranteed to exist for the duration of the batch buffer's life.
v2: Rebased to newer tree and updated for changes to the command parser.
Specifically, a code shuffle has required saving the batch start address in the
params structure.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The i915_add_request() function is called to keep track of work that has been
written to the ring buffer. It adds epilogue commands to track progress (seqno
updates and such), moves the request structure onto the right list and other
such house keeping tasks. However, the work itself has already been written to
the ring and will get executed whether or not the add request call succeeds. So
no matter what goes wrong, there isn't a whole lot of point in failing the call.
At the moment, this is fine(ish). If the add request does bail early on and not
do the housekeeping, the request will still float around in the
ring->outstanding_lazy_request field and be picked up next time. It means
multiple pieces of work will be tagged as the same request and driver can't
actually wait for the first piece of work until something else has been
submitted. But it all sort of hangs together.
This patch series is all about removing the OLR and guaranteeing that each piece
of work gets its own personal request. That means that there is no more
'hoovering up of forgotten requests'. If the request does not get tracked then
it will be leaked. Thus the add request call _must_ not fail. The previous patch
should have already ensured that it _will_ not fail by removing the potential
for running out of ring space. This patch enforces the rule by actually removing
the early exit paths and the return code.
Note that if something does manage to fail and the epilogue commands don't get
written to the ring, the driver will still hang together. The request will be
added to the tracking lists. And as in the old case, any subsequent work will
generate a new seqno which will suffice for marking the old one as complete.
v2: Improved WARNings (Tomas Elf review request).
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It is a bad idea for i915_add_request() to fail. The work will already have been
send to the ring and will be processed, but there will not be any tracking or
management of that work.
The only way the add request call can fail is if it can't write its epilogue
commands to the ring (cache flushing, seqno updates, interrupt signalling). The
reasons for that are mostly down to running out of ring buffer space and the
problems associated with trying to get some more. This patch prevents that
situation from happening in the first place.
When a request is created, it marks sufficient space as reserved for the
epilogue commands. Thus guaranteeing that by the time the epilogue is written,
there will be plenty of space for it. Note that a ring_begin() call is required
to actually reserve the space (and do any potential waiting). However, that is
not currently done at request creation time. This is because the ring_begin()
code can allocate a request. Hence calling begin() from the request allocation
code would lead to infinite recursion! Later patches in this series remove the
need for begin() to do the allocate. At that point, it becomes safe for the
allocate to call begin() and really reserve the space.
Until then, there is a potential for insufficient space to be available at the
point of calling i915_add_request(). However, that would only be in the case
where the request was created and immediately submitted without ever calling
ring_begin() and adding any work to that request. Which should never happen. And
even if it does, and if that request happens to fall down the tiny window of
opportunity for failing due to being out of ring space then does it really
matter because the request wasn't doing anything in the first place?
v2: Updated the 'reserved space too small' warning to include the offending
sizes. Added a 'cancel' operation to clean up when a request is abandoned. Added
re-initialisation of tracking state after a buffer wrap to keep the sanity
checks accurate.
v3: Incremented the reserved size to accommodate Ironlake (after finally
managing to run on an ILK system). Also fixed missing wrap code in LRC mode.
v4: Added extra comment and removed duplicate WARN (feedback from Tomas).
For: VIZ-5115
CC: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have enough generic hotplug functions sprinkled all over i915_irq.c
to warrant moving them to a file of their own. This should further
underline the distinction between generic code in the new file and
platform specific hotplug and irq code that remains in i915_irq.c.
Add new intel_hpd_init_work to keep work functions static, and rename
get_port_from_pin to intel_hpd_pin_to_port while increasing its
visibility, but keep everything else the same.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The skylake scalers depend on the cdclk freq, but that frequency can
change during a modeset. So when a modeset happens calculate the new
cdclk in the atomic state. With the transitional helpers gone the
cached value can be used in the scaler, and committed after all
crtc's are disabled.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90874
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because we're currently using FBC_UNSUPPORTED_MODE for two different
cases.
This commit will also allow us to write the next one without hiding
information from the user.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The i915 atomic conversion is a real beast and it's not getting easier
wrangling in a separate branch. I'm might be regretting this, but
right after vacation nothing can burst my little bubble here!
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
In igt, we want to test handling of GPU hangs, both for recovery
purposes and for reporting. However, we don't want to inject a genuine
GPU hang onto a machine that cannot recover and so be permenantly
wedged. Rather than embed heuristics into igt, have the kernel report
exactly when it expects the GPU reset to work.
This can also be usefully extended in future to indicate different
levels of fine-grained resets.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tim Gore <tim.gore@intel.com>
Cc: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
