Modules: HDA Codec driver
The following patch adds a 'test' ALC260 model specification to the
patch_realtek.c driver if CONFIG_SND_DEBUG is set. This is similar to the
'test' ALC880 model in that it sets up mixer controls for almost everything
to make it easier for people to test their laptop/soundcard when working out
what pin widgets are connected to which real-world devices.
This patch assumes my previous patch (adding the second PCM to the ALC260)
has previously been applied since it uses infrastructure added by that
patch.
In developing this patch it was found that not all retasking pins accept all
the modes - in particular, some ignore the VREFxx variants. The pin mode
control has therefore been tweaked to prevent this becoming a problem in
mixer applications.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Codec driver
Jonathan Woithe <jwoithe@physics.adelaide.edu.au>
The following patch changes the initverbs associated with the output sum
widgets 0x08, 0x09 and 0x0a used with the fujitsu model in patch_realtek.c.
It is against alsa 1.0.11rc3.
Currently these widgets have their output muted, but a close reading of the
datasheet suggests that they don't actually have an output mute. They have
an *input* mute for each of their two inputs and a single output gain. This
patch therefore activates the input mutes and zeros the output gain. It has
not yet been tested but the above interpretation of the ALC260 datasheet
seems correct.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Codec driver
The following patch against alsa 1.0.11rc3 creates a PCM device (pcm1c) for
the second ADC present on the ALC260 codec used by the hda driver. It also
defines a new mixer control allowing the mode of retasking pins to be set;
this means a user can (for example) designate the headphone jack to be a
second input. With this patch in place it is possible to do 4 channel
recording on laptops equipped with an ALC260 codec assuming both a stereo
line-in jack is provided in addition to a headphone jack.
Mixer controls are provided to allow the headphone jack to be switched as
an input. In addition, an (input only) mode control is configured for
the line-in jack to allow a bias voltage to be requested (VREF80 or VREF50)
so headsets based on condensor microphones have a chance of working.
This patch has been tested on a Fujitsu S7020 laptop and as such these
features are currently only configured for the 'fujitsu' model.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: AC97 Codec
Added the support of static resolution table support for codecs
that the driver cannot probe the volume resolution properly.
The table pointer should be set in each codec patch.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: BT87x driver
- added 0x107d:0x6606 to whitelist
- print also the pci device ID for developers when model is not known
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Modules: ICE1712 driver
Change the value written to hardware configuration register of envy24 chip
in the case of Terratec DMX6fire to restrict the active ADCs & DACs to 6.
Also add the dxr_enable module option to eventually leave the old behaviour
when user requests.
Signed-off-by: Alan Horstmann <gineera@aspect135.co.uk>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Modules: USB generic driver
Rename QUIRK_MIDI_MIDITECH to QUIRK_MIDI_CME because Miditech keyboards
are built by CME and use the same protocol, and don't force a Miditech
product name for the USB ID used by both Miditech and CME UF-x
keyboards.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: PCM Midlevel,USB generic driver
Because snd_pcm_format_name() function is used only for informational
purposes, it is no longer exported from the PCM midlevel to reduce
space and dependency. usbaudio module shows only numeric value for format.
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Modules: YMFPCI driver
Added rear_swap module option / kernel parameter to configure the rear
channel swapping. Default value is enable to make the AC3 passthrough
working, but analog only users might revert the previous behaviour.
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: ES18xx driver
Forth of 4 es18xx.c patches culminating in Zoom Video support.
This patch adds Zoom Video support for those chipsets that support it.
Testing:
This work was initially done on the source from the Debian Sarge ALSA
package, then tested
on an ES1879. I could not test the Zoom Video function for an ES1878 or
ES1869.
Patches were created against the Sarge code and then edited to apply
correctly to the
ALSA cvs code. Lastly the patched ALSA cvs code was test for successful
compilation.
No additional testing was done on the ALSA cvs version.
One quirk (noted in my comments below) is that apparently the datasheet
is wrong
for one of the ES1879 Zoom Video 'enable' bits, because
1) if you set this bit it messes up PCM playback (speaker_test play a
lower frequency)
2) even if you don't set this bit Zoom Video still works.
I added a control to toggle the bit on just in case there might be a
version of the
ES1879 that requires it, but I expect noone will need it.
Signed-off-by: Mark Salazar <markTheCoder@justmyself.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: ES18xx driver
Third of 4 es18xx.c patches culminating in Zoom Video support.
This patch changes the Hardware Volume support to reflect the fact that
not all of the
supported chipsets have seperate registers dedicated to the Hardware
Volume inputs. Although
all the chipsets can generate an HWV interrupt whenever a Hardware
Volume input is received
only those with seperate HWV registers can split the HWV registers from
the Master volume
registers.
Testing:
This work was initially done on the source from the Debian Sarge ALSA
package, then tested
on an ES1879 and an ES1878 machine. Patches were created against the
Sarge code and then edited
to apply correctly to the ALSA cvs code. Lastly the patched ALSA cvs
code was test for
successful compilation. No additional testing was done on the ALSA cvs
version.
Signed-off-by: Mark Salazar <markTheCoder@justmyself.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: ES18xx driver
Second of 4 es18xx.c patches culminating in Zoom Video support.
This patch changes the 'record source' mux routines to reflect the fact
that not all of the
supported chipsets have 8 possible inputs. Some have 4 and some have 5.
Testing:
This work was initially done on the source from the Debian Sarge ALSA
package, then tested
on an ES1879 and an ES1878 machine. Patches were created against the
Sarge code and then edited
to apply correctly to the ALSA cvs code. Lastly the patched ALSA cvs
code was test for
successful compilation. No additional testing was done on the ALSA cvs
version.
Signed-off-by: Mark Salazar <markTheCoder@justmyself.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: ES18xx driver
First of 4 es18xx.c patches culminating in Zoom Video support.
While adding support for Zoom Video to the es18xx driver I found some of
the mixer controls
were wrong. Since you guys went to the trouble of supplying the
datasheets for the supported
chipsets I did a review of all of them and tried to get es18xx.c to
accurately reflect the
proper mixer controls for each chipset. If the datasheets are wrong then
so are my patches.
This first patch moves some controls from the common-to-all-chipsets array
'snd_es18xx_base_controls' to a chipset-specific array and adds code to
manage that new array.
Also while testing on my ES1878 test machine I discovered it needed a
couple of udelays in
the identify function so those are in this patch as well.
Testing:
This work was initially done on the source from the Debian Sarge ALSA
package, then tested
on an ES1879 and an ES1878 machine. Patches were created against the
Sarge code and then edited
to apply correctly to the ALSA cvs code. Lastly the patched ALSA cvs
code was test for
successful compilation. No additional testing was done on the ALSA cvs
version.
Signed-off-by: Mark Salazar <markTheCoder@justmyself.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: au88x0 driver
Fix the driver codes to run on 64bit architectures.
The patch taken from ALSA BTS bug#1047.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: ALSA Core,PCM Midlevel,ALSA<-OSS emulation,USB generic driver
1) The verbose procfs code for the PCM midlevel and usb audio
can be removed now (more patches will follow).
CONFIG_SND_VERBOSE_PROCFS
2) The PCM OSS plugin system can be also compiled optionaly.
CONFIG_SND_PCM_OSS_PLUGINS
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Modules: YMFPCI driver
The routing of the effect 2/3 channels to the digital output is the
opposite of the rear analog output (left/right swapped).
We make the order correct for the digital output (which will make the
analog rear have the channels swapped) to make AC3 output work.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: Documentation,HDA Intel driver
Added single_cmd module option for debugging in the case CORB/RIRB
doesn't work well (e.g. due to wrong irq routings).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: Intel8x0 driver
Fix the detection of tertriary codec on SIS7012, including clean-ups
of relevant codes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: USB generic driver
Move the common packet size calculation code from
prepare_startup_playback_urb() and prepare_playback_urb() to a new
function.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: USB generic driver
This is my naive attempt at adding ALSA device support. The attached
patch provides support for the EDIROL UM-3ex. This is a 3-port USB midi
interface with a built-in USB hub and the ability to chain 2 other
UM-3x's in a master-slave configuration. I only have one, so I do not
know how this works in practice.
Though this is a 3-port device, I had to throw in that 4th 'Control' interface
to the definition in order to make the 3rd port work. If I set in/out_cables
to 0x000b, a 3rd interface appears on the driver, but it does nothing.
Changing it to 0x000f allows the 3rd interface to work, but of course
interface 4 does not work because it does not exist.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6: (230 commits)
[SPARC64]: Update defconfig.
[SPARC64]: Fix 2 bugs in huge page support.
[SPARC64]: CONFIG_BLK_DEV_RAM fix
[SPARC64]: Optimized TSB table initialization.
[SPARC64]: Allow CONFIG_MEMORY_HOTPLUG to build.
[SPARC64]: Use SLAB caches for TSB tables.
[SPARC64]: Don't kill the page allocator when growing a TSB.
[SPARC64]: Randomize mm->mmap_base when PF_RANDOMIZE is set.
[SPARC64]: Increase top of 32-bit process stack.
[SPARC64]: Top-down address space allocation for 32-bit tasks.
[SPARC64] bbc_i2c: Fix cpu check and add missing module license.
[SPARC64]: Fix and re-enable dynamic TSB sizing.
[SUNSU]: Fix missing spinlock initialization.
[TG3]: Do not try to access NIC_SRAM_DATA_SIG on Sun parts.
[SPARC64]: First cut at VIS simulator for Niagara.
[SPARC64]: Fix system type in /proc/cpuinfo and remove bogus OBP check.
[SPARC64]: Add SMT scheduling support for Niagara.
[SPARC64]: Fix 32-bit truncation which broke sparsemem.
[SPARC64]: Move over to sparsemem.
[SPARC64]: Fix new context version SMP handling.
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/shaggy/jfs-2.6:
JFS: add uid, gid, and umask mount options
JFS: Take logsync lock before testing mp->lsn
JFS: kzalloc conversion
JFS: Add missing file from fa3241d24c
JFS: Use the kthread_ API
JFS: Fix regression. fsck complains if symlinks do not have INLINEEA attribute
JFS: ext2 inode attributes for jfs
JFS: semaphore to mutex conversion.
JFS: make buddy table static
JFS: Add back directory i_size calculations for legacy partitions
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (150 commits)
[PATCH] ipw2100: Update version ipw2100 stamp to 1.2.2
[PATCH] ipw2100: move mutex.h include from ipw2100.c to ipw2100.h
[PATCH] ipw2100: semaphore to mutexes conversion
[PATCH] ipw2100: Fix radiotap code gcc warning
[PATCH] ipw2100: add radiotap headers to packtes captured in monitor mode
[PATCH] ipw2x00: expend Copyright to 2006
[PATCH] drivers/net/wireless/ipw2200.c: fix an array overun
[PATCH] ieee80211: Don't update network statistics from off-channel packets.
[PATCH] ipw2200: Update ipw2200 version stamp to 1.1.1
[PATCH] ipw2200: switch to the new ipw2200-fw-3.0 image format
[PATCH] ipw2200: wireless extension sensitivity threshold support
[PATCH] ipw2200: Enables the "slow diversity" algorithm
[PATCH] ipw2200: Set a meaningful silence threshold value
[PATCH] ipw2200: export `debug' module param only if CONFIG_IPW2200_DEBUG
[PATCH] ipw2200: Change debug level for firmware error logging
[PATCH] ipw2200: Filter unsupported channels out in ad-hoc mode
[PATCH] ipw2200: Fix ipw_sw_reset() implementation inconsistent with comment
[PATCH] ipw2200: Fix rf_kill is activated after mode change with 'disable=1'
[PATCH] ipw2200: remove the WPA card associates to non-WPA AP checking
[PATCH] ipw2200: Add signal level to iwlist scan output
...
