The error paths for xiic_reinit() return negative values on failure
and 0 on success - this error message therefore is triggered on
_success_ rather than failure. Correct the condition so it's only
shown on failure as intended.
Fixes: 8fa9c93880 ("i2c: xiic: return value of xiic_reinit")
Signed-off-by: Daniel Scally <dan.scally@ideasonboard.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In i2c_mux_gpio_probe_fw(), we should add fwnode_handle_put()
when break out of the iteration device_for_each_child_node()
as it will automatically increase and decrease the refcounter.
Fixes: 98b2b712bc ("i2c: i2c-mux-gpio: Enable this driver in ACPI land")
Signed-off-by: Liang He <windhl@126.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
devm_kstrdup() returns pointer to allocated string on success,
NULL on failure. So it is better to check the return value of it.
Fixes: e35478eac0 ("i2c: mux: demux-pinctrl: run properly with multiple instances")
Signed-off-by: Xiaoke Wang <xkernel.wang@foxmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The DesignWare IP can be synthesized with the IC_EMPTYFIFO_HOLD_MASTER_EN
parameter.
In this case, when the TX FIFO gets empty and the last command didn't have
the STOP bit (IC_DATA_CMD[9]), the controller will hold SCL low until
a new command is pushed into the TX FIFO or the transfer is aborted.
When the controller is holding SCL low, it cannot be disabled.
The transfer must first be aborted.
Also, the bus recovery won't work because SCL is held low by the master.
Check if the master is holding SCL low in __i2c_dw_disable() before trying
to disable the controller. If SCL is held low, an abort is initiated.
When the abort is done, then proceed with disabling the controller.
This whole situation can happen for instance during SMBus read data block
if the slave just responds with "byte count == 0".
This puts the driver in an unrecoverable state, because the controller is
holding SCL low and the current __i2c_dw_disable() procedure is not
working. In this situation only a SoC reset can fix the i2c bus.
Co-developed-by: Jonathan Borne <jborne@kalray.eu>
Signed-off-by: Jonathan Borne <jborne@kalray.eu>
Signed-off-by: Yann Sionneau <ysionneau@kalray.eu>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
We have to unregister tco_pdev also if i2c_add_adapter() fails.
Fixes: 9424693035 ("i2c: i801: Create iTCO device on newer Intel PCHs")
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This fixes the below warnings
drivers/i2c/busses/i2c-cadence.c:221: warning: Function parameter or
member 'rinfo' not described in 'cdns_i2c'
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202308171510.bKHBcZQW-lkp@intel.com/
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Reset the i2c controller when an i2c transfer timeout occurs.
The remaining interrupts and device should be reset to avoid
unpredictable controller behavior.
Fixes: 2e57b7cebb ("i2c: aspeed: Add multi-master use case support")
Cc: <stable@vger.kernel.org> # v5.1+
Signed-off-by: Tommy Huang <tommy_huang@aspeedtech.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The "i2c_mlxcpld" platform device is only instantiated on X86 systems
(through drivers/platform/x86/mlx-platform.c), or on ARM64 systems with
ACPI (through drivers/platform/mellanox/nvsw-sn2201.c). Hence further
restrict the dependency on ARM64 to ACPI, to prevent asking the user
about this driver when configuring an ARM64 kernel without ACPI support.
While at it, document in the Kconfig help text that the driver supports
ARM64/ACPI based systems, too.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Vadim Pasternak <vadimp@nvidia.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
I2C Address Translator (ATR) support is not a stand-alone driver, but a
library. All of its users select I2C_ATR. Hence there is no need for
the user to enable this symbol manually, except when compile-testing.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
a lot of developers were on holidays (including myself) it was a good
timing to apply lots of cleanups which would normally cause merge
conflicts with other floating patches. Extra thanks go to Andi Shyti who
backed me up when I was on a four week hiatus. This is also the reason
that some patches were commited later than ideal.
-----BEGIN PGP SIGNATURE-----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=gpYJ
-----END PGP SIGNATURE-----
Merge tag 'i2c-for-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"I2C has mainly cleanups this time and a few driver improvements.
Because a lot of developers were on holidays (including myself) it was
a good timing to apply lots of cleanups which would normally cause
merge conflicts with other floating patches. Extra thanks go to Andi
Shyti who backed me up when I was on a four week hiatus. This is also
the reason that some patches were commited later than ideal"
* tag 'i2c-for-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (67 commits)
i2c: at91: Use dev_err_probe() instead of dev_err()
I2C: ali15x3: Do PCI error checks on own line
i2c: Make return value check more accurate and explicit for devm_pinctrl_get()
i2c: designware: Add support for recovery when GPIO need pinctrl
i2c: mlxcpld: Add support for extended transaction length
i2c: mlxcpld: Allow driver to run on ARM64 architecture
i2c: nforce2: Do PCI error check on own line
i2c: sis5595: Do PCI error checks on own line
i2c: qcom-cci: Fix error checking in cci_probe()
i2c: muxes: pca954x: Add regulator support
i2c: muxes: pca954x: Add MAX735x/MAX736x support
dt-bindings: i2c: Add Maxim MAX735x/MAX736x variants
dt-bindings: i2c: pca954x: Correct interrupt support
i2c: pnx: Use devm_platform_get_and_ioremap_resource()
i2c: pxa: Use devm_platform_get_and_ioremap_resource()
i2c: s3c2410: Use devm_platform_get_and_ioremap_resource()
i2c: sh_mobile: Use devm_platform_get_and_ioremap_resource()
i2c: st: Use devm_platform_get_and_ioremap_resource()
i2c: qcom-geni: Convert to devm_platform_ioremap_resource()
i2c: stm32f4: Use devm_platform_get_and_ioremap_resource()
...
-----BEGIN PGP SIGNATURE-----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=yuz5
-----END PGP SIGNATURE-----
Merge tag 'media/v6.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new i2c drivers: ds90ub913, ds90ub953, ds90ub960, dw9719, ds90ub913
- new Intel IVSC MEI drivers
- some Mediatek platform drivers were moved to a common location
- Intel atomisp2 driver is now working with the main ov2680 driver. Due
to that, the atomisp2 ov2680 staging one was removed
- the bttv driver was finally converted to videobuf2 framework. This
was the last one upstream using videobuf version 1 core. We'll likely
remove the old videobuf framework on 6.7
- lots of improvements at atomisp driver: it now works with normal I2C
sensors. Several compile-mode dependecies to select between ISP2400
and ISP2401 are now solved in runtime
- a new ipu-bridge logic was added to work with IVSC MEI drivers
- venus driver gained better support for new VPU versions
- the v4l core async framework has gained lots of improvements and
cleanups
- lots of other cleanups, improvements and driver fixes
* tag 'media/v6.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (358 commits)
media: ivsc: Add ACPI dependency
media: bttv: convert to vb2
media: bttv: use audio defaults for winfast2000
media: bttv: refactor bttv_set_dma()
media: bttv: move vbi_skip/vbi_count out of buffer
media: bttv: remove crop info from bttv_buffer
media: bttv: remove tvnorm field from bttv_buffer
media: bttv: remove format field from bttv_buffer
media: bttv: move do_crop flag out of bttv_fh
media: bttv: copy vbi_fmt from bttv_fh
media: bttv: copy vid fmt/width/height from fh
media: bttv: radio use v4l2_fh instead of bttv_fh
media: bttv: replace BUG with WARN_ON
media: bttv: use video_drvdata to get bttv
media: i2c: rdacm21: Fix uninitialized value
media: coda: Remove duplicated include
media: vivid: fix the racy dev->radio_tx_rds_owner
media: i2c: ccs: Check rules is non-NULL
media: i2c: ds90ub960: Fix PLL config for 1200 MHz CSI rate
media: i2c: ds90ub953: Fix use of uninitialized variables
...
Change
if (IS_ERR(x)) { dev_err(...); return PTR_ERR(x); }
into
return dev_err_probe()
Also, return the correct error instead of hardcoding -ENODEV
This change has also the advantage of handling the -EPROBE_DEFER situation.
Signed-off-by: Yann Sionneau <yann@sionneau.net>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Instead of if conditions with line splits, use the usual error handling
pattern with a separate variable to improve readability.
No functional changes intended.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If pinctrl is not available (thus devm_pinctrl_get() returns NULL) then
recovery can't work, because we can't switch the I2C pins between the
I2C controller and GPIO. So, it is quite correct to print
"can't get pinctrl, bus recovery not supported" because the I2C bus
can't be recovered without pinctrl.
The PTR_ERR() is also fine - because if pinctrl is not present and
returns NULL, we'll end up returning zero, which is exactly what we
want.
However, open code that with a more accurate message will be more explicit
for NULL case when CONFIG_PINCTRL is not defined.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Currently if the SoC needs pinctrl to switch the SCL and SDA from the I2C
function to GPIO function, the recovery won't work.
scl-gpio = <>;
sda-gpio = <>;
Are not enough for some SoCs to have a working recovery.
Some need:
scl-gpio = <>;
sda-gpio = <>;
pinctrl-names = "default", "recovery";
pinctrl-0 = <&i2c_pins_hw>;
pinctrl-1 = <&i2c_pins_gpio>;
The driver was not filling rinfo->pinctrl with the device node
pinctrl data which is needed by generic recovery code.
Signed-off-by: Yann Sionneau <ysionneau@kalray.eu>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add support for extended length of read and write transactions.
New FPGA logic allows to increase size of the read and write
transactions length. This feature is verified through capability
register 'CPBLTY_REG'. Two bits 5 and 6 of the register are used for
length capability detection. Value '10' indicates support of extended
transaction length - 128 bytes for read transactions and 132 for write
transactions.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Michael Shych <michaelsh@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Instead of a if condition with a line split, use the usual error
handling pattern with a separate variable to improve readability.
No functional changes intended.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Instead of if conditions with line splits, use the usual error handling
pattern with a separate variable to improve readability.
No functional changes intended.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
devm_clk_bulk_get_all() can return zero when no clocks are obtained.
Passing zero to dev_err_probe() is a success which is incorrect.
Fixes: 605efbf438 ("i2c: qcom-cci: Use dev_err_probe in probe function")
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add a vdd regulator and enable it for boards that have the
mux powered off by default.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add support for the following Maxim chips using the existing PCA954x
driver:
- MAX7356
- MAX7357
- MAX7358
- MAX7367
- MAX7368
- MAX7369
All added Maxim chips behave like the PCA954x, where a single SMBUS byte
write selects up to 8 channels to be bridged to the primary bus.
While the MAX7357/MAX7358 have interrupt support, they don't act as
interrupt controller like the PCA9545 does. Thus don't enable IRQ support
and handle them like the PCA9548.
Tested using the MAX7357.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
iproc_i2c_rd_reg() and iproc_i2c_wr_reg() are called from both
interrupt context (e.g. bcm_iproc_i2c_isr) and process context
(e.g. bcm_iproc_i2c_suspend). Therefore, interrupts should be
disabled to avoid potential deadlock. To prevent this scenario,
use spin_lock_irqsave().
Fixes: 9a10387280 ("i2c: iproc: add NIC I2C support")
Signed-off-by: Chengfeng Ye <dg573847474@gmail.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Reviewed-by: Kamal Dasu <kamal.dasu@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The "ret" variable is uninitialized. It was the "p2wi->rstc" variable
that was intended. We can also use the %pe string format to print the
error code name instead of just the number.
Fixes: 75ff8a340a ("i2c: sun6i-p2wi: Use devm_clk_get_enabled()")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The controller may be shared with other port, for example the firmware.
Handle the interrupt from other sources will cause crash since some
data are not initialized. So only handle the interrupt of the driver's
transfer and discard others.
Fixes: d62fbdb99a ("i2c: add support for HiSilicon I2C controller")
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20230801124625.63587-1-yangyicong@huawei.com
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Tegra processors prior to Tegra186 used APB DMA for I2C requiring
CONFIG_TEGRA20_APB_DMA=y while Tegra186 and later use GPC DMA requiring
CONFIG_TEGRA186_GPC_DMA=y.
The check for if the processor uses APB DMA is inverted and so the wrong
DMA config options are checked.
This means if CONFIG_TEGRA20_APB_DMA=y but CONFIG_TEGRA186_GPC_DMA=n
with a Tegra186 or later processor the driver will incorrectly think DMA is
enabled and attempt to request DMA channels that will never be availible,
leaving the driver in a perpetual EPROBE_DEFER state.
Fixes: 48cb6356fa ("i2c: tegra: Add GPCDMA support")
Signed-off-by: Parker Newman <pnewman@connecttech.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Akhil R <akhilrajeev@nvidia.com>
Link: https://lore.kernel.org/r/fcfcf9b3-c8c4-9b34-2ff8-cd60a3d490bd@connecttech.com
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If the driver fails to obtain a DMA channel, it will initiate cleanup
and try to release the DMA channel that couldn't be retrieved. This will
cause a crash because the cleanup will try to dereference an ERR_PTR()-
encoded error code.
However, there's nothing to clean up at this point yet, so we can avoid
this by simply resetting the DMA channel to NULL instead of storing the
error code.
Fixes: fcc8a89a1c ("i2c: tegra: Share same DMA channel for RX and TX")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tested-by: Akhil R <akhilrajeev@nvidia.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In the I2C_FUNC_SMBUS_BLOCK_DATA case, the invalid length byte value
(outside of 1-32) of the SMBus block data response from the Slave device
is not correctly handled by the I2C Designware driver.
In case IC_EMPTYFIFO_HOLD_MASTER_EN==1, which cannot be detected
from the registers, the Master can be disabled only if the STOP bit
is set. Without STOP bit set, the Master remains active, holding the bus
until receiving a block data response length. This hangs the bus and
is unrecoverable.
Avoid this by issuing another dump read to reach the stop condition when
an invalid length byte is received.
Cc: stable@vger.kernel.org
Signed-off-by: Tam Nguyen <tamnguyenchi@os.amperecomputing.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230726080001.337353-3-tamnguyenchi@os.amperecomputing.com
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Commit 0daede80f8 ("i2c: designware: Convert driver to using regmap API")
changes the logic to validate the whole 32-bit return value of
DW_IC_DATA_CMD register instead of 8-bit LSB without reason.
Later, commit f53f15ba5a ("i2c: designware: Get right data length"),
introduced partial fix but not enough because the "tmp > 0" still test
tmp as 32-bit value and is wrong in case the IC_DATA_CMD[11] is set.
Revert the logic to just before commit 0daede80f8
("i2c: designware: Convert driver to using regmap API").
Fixes: f53f15ba5a ("i2c: designware: Get right data length")
Fixes: 0daede80f8 ("i2c: designware: Convert driver to using regmap API")
Cc: stable@vger.kernel.org
Signed-off-by: Tam Nguyen <tamnguyenchi@os.amperecomputing.com>
Signed-off-by: Quan Nguyen <quan@os.amperecomputing.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230726080001.337353-2-tamnguyenchi@os.amperecomputing.com
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
On MX8X platforms, the default clock rate is 0 if without explicit
clock setting in dts nodes. I2c can't work when i2c peripheral clk
rate is 0.
Add a i2c peripheral clk rate check before configuring the clock
register. When i2c peripheral clk rate is 0 and directly return
-EINVAL.
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Acked-by: Dong Aisheng <Aisheng.dong@nxp.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Patch allows usb devices with multiple interfaces to use this driver without
this driver assuming all interfaces are i2c-tiny-usb.
Signed-off-by: Harry Geyer <harry.geyer@devtank.co.uk>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20230727162255.21551-1-harry.geyer@devtank.co.uk
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Use the dev_err_probe function instead of dev_err in the probe function
so that the printed message includes the return value and also handles
-EPROBE_DEFER nicely.
Signed-off-by: Liao Chang <liaochang1@huawei.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20230808012954.1643834-10-liaochang1@huawei.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Use the dev_err_probe function instead of dev_err in the probe function
so that the printed message includes the return value and also handles
-EPROBE_DEFER nicely.
Signed-off-by: Liao Chang <liaochang1@huawei.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20230808012954.1643834-9-liaochang1@huawei.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Use the dev_err_probe function instead of dev_err in the probe function
so that the printed message includes the return value and also handles
-EPROBE_DEFER nicely.
Signed-off-by: Liao Chang <liaochang1@huawei.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20230808012954.1643834-8-liaochang1@huawei.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Use the dev_err_probe function instead of dev_err in the probe function
so that the printed message includes the return value and also handles
-EPROBE_DEFER nicely.
Signed-off-by: Liao Chang <liaochang1@huawei.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20230808012954.1643834-7-liaochang1@huawei.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Use the dev_err_probe function instead of dev_err in the probe function
so that the printed message includes the return value and also handles
-EPROBE_DEFER nicely.
Signed-off-by: Liao Chang <liaochang1@huawei.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20230808012954.1643834-6-liaochang1@huawei.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Use the dev_err_probe function instead of dev_err in the probe function
so that the printed message includes the return value and also handles
-EPROBE_DEFER nicely.
Signed-off-by: Liao Chang <liaochang1@huawei.com>
Reviewed-by: Yicong Yang <yangyicong@hisilicon.com>
Link: https://lore.kernel.org/r/20230808012954.1643834-5-liaochang1@huawei.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
