Sum up rx/tx bytes in software as we do for rx/tx packets, to be reported
in upcoming statistics fix.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon changing num_channels, reset the RSS indirection table to
match the new value.
Fixes: 2d75b2bc8a ('net/mlx5e: Add ethtool RSS configuration options')
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should modify TIRs explicitly to apply the new RSS configuration.
The light ndo close/open calls do not "refresh" them.
Fixes: 2d75b2bc8a ('net/mlx5e: Add ethtool RSS configuration options')
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Readers/Writers lock for SW timecounter was acquired without disabling
interrupts on local CPU.
The problematic scenario:
* HW timestamping is enabled
* Timestamp overflow periodic service task is running on local CPU and
holding write_lock for SW timecounter
* Completion arrives, triggers interrupt for local CPU.
Interrupt routine calls napi_schedule(), which triggers rx/tx
skb process.
An attempt to read SW timecounter using read_lock is done, which is
already locked by a writer on the same CPU and cause soft lockup.
Add irqsave/irqrestore for when using the readers/writers lock for
writing.
Fixes: ef9814deaf ('net/mlx5e: Add HW timestamping (TS) support')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethtool LRO enable/disable is broken, as of today we only modify TCP
TIRs in order to apply the requested configuration.
Hardware requires that all TIRs pointing to the same RQ should share the
same LRO configuration. For that all other TIRs' LRO fields must be
modified as well.
Fixes: 5c50368f38 ('net/mlx5e: Light-weight netdev open/stop')
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the MLX5E_CQ_HAS_CQES optimization flag, the following buggy
flow might occur:
- Suppose RX is always busy, TX has a single packet every second.
- We poll a single TX cqe and clear its flag.
- We never arm it again as RX is always busy.
- TX CQ flag is never changed, and new TX cqes are not polled.
We revert this optimization.
Fixes: e586b3b0ba ('net/mlx5: Ethernet Datapath files')
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For RTL8168G/RTL8168H/RTL8411B/RTL8107E, enable this flag to eliminate
message "AMD-Vi: Event logged [IO_PAGE_FAULT device=01:00.0 domain=0x0002
address=0x0000000000003000 flags=0x0050] in dmesg.
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* check GCMP encryption vs. fragmentation properly; we'd found
this problem quite a while ago but waited for the 802.11 spec
to be updated
* fix RTS/CTS logic in minstrel_ht
* fix RX of certain public action frames in AP mode
* add mac80211_hwsim to MAC80211 in MAINTAINERS, this helps
the kbuild robot pick up the right tree for it
-----BEGIN PGP SIGNATURE-----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=2rZC
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2016-03-02' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Here are a few more fixes for the current cycle:
* check GCMP encryption vs. fragmentation properly; we'd found
this problem quite a while ago but waited for the 802.11 spec
to be updated
* fix RTS/CTS logic in minstrel_ht
* fix RX of certain public action frames in AP mode
* add mac80211_hwsim to MAC80211 in MAINTAINERS, this helps
the kbuild robot pick up the right tree for it
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Schmidt says:
====================
bnx2x: endianness fixes
this fixes a VLAN crash and some SRIOV bugs in bnx2x observed on ppc64.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
For consistency with other event data structs and to lessen
the chance of a mistake should one of the reserved fields become
used in the future, define the reserved fields as little-endian.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were no missing endianness conversions in this case, but the
fields of struct cfc_del_event_data should be defined as little-endian
to get rid of the ugly (__force __le32) casts.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's not really a bug, but it was odd that bnx2x_eq_int() read the
message data as if it were a cfc_del_event regardless of the event type.
It's cleaner to access only the appropriate member of union event_data
after checking the event opcode.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On ppc64 the PF did not receive messages from VFs correctly.
Fields of struct vf_pf_event_data are little-endian.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VF is sending a message to the PF, it needs to trigger the PF
to tell it the message is ready.
The trigger did not work on ppc64. No interrupt appeared in the PF.
The bug is due to confusion about the layout of struct trigger_vf_zone.
In bnx2x_send_msg2pf() the trigger is written using writeb(), not
writel(), so the attempt to define the struct with a reversed layout on
big-endian is counter-productive.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x crashes during the initialization of the 8021q module on ppc64.
The bug is a missing conversion from le32 in
bnx2x_handle_classification_eqe() when obtaining the cid value from
struct eth_event_data.
The fields in struct eth_event_data should all be declared as
little-endian and conversions added where missing.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull parisc fixes from Helge Deller:
"We wire up the copy_file_range syscall, fix two bugs in the parisc
ptrace code and have a trivial fix for floppy.h to clarify an
expression with parentheses"
* 'parisc-4.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Wire up copy_file_range syscall
parisc: Fix ptrace syscall number and return value modification
parisc: Use parentheses around expression in floppy.h
Pull cifs fixes from Steve French:
"Various small CIFS/SMB3 fixes for stable:
Fixes address oops that can occur when accessing Macs with SMB3, and
another problem found to Samba when read responses queued (e.g. with
gluster under Samba)"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
CIFS: Fix duplicate line introduced by clone_file_range patch
Fix cifs_uniqueid_to_ino_t() function for s390x
CIFS: Fix SMB2+ interim response processing for read requests
cifs: fix out-of-bounds access in lease parsing
The exit path will do some final updates to the VM of an exiting process
to inform others of the fact that the process is going away.
That happens, for example, for robust futex state cleanup, but also if
the parent has asked for a TID update when the process exits (we clear
the child tid field in user space).
However, at the time we do those final VM accesses, we've already
stopped accepting signals, so the usual "stop waiting for userfaults on
signal" code in fs/userfaultfd.c no longer works, and the process can
become an unkillable zombie waiting for something that will never
happen.
To solve this, just make handle_userfault() abort any user fault
handling if we're already in the exit path past the signal handling
state being dead (marked by PF_EXITING).
This VM special case is pretty ugly, and it is possible that we should
look at finalizing signals later (or move the VM final accesses
earlier). But in the meantime this is a fairly minimally intrusive fix.
Reported-and-tested-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In amdgpu_connector_hotplug(), we need to start DP link
training only after we have received DPCD. The function
amdgpu_atombios_dp_get_dpcd() returns non-zero value only
when an error condition is met, otherwise returns zero.
So in case the function encounters an error, we need to
skip rest of the code and return from amdgpu_connector_hotplug()
immediately. Only when we are successfull in reading DPCD
pin, we should carry on with turning-on the monitor.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
This code path is not currently enabled now that we properly
respect the vce pg flags, so uncomment the actual pg calls
so the code is as it should be we are eventually able to
enable vce pg.
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If we don't disable it when vce is not in use, we use extra power
if vce pg is disabled.
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
I missed this when cleaning up the vce pg handling.
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Select between me and pfp properly.
Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We never ported that back to CIK, so we could run into VM faults here.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
with this event, powerplay can adjust current power state if needed.
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
This is needed to init the dynamic states without a display. To be
used in the next commit.
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
On CI, we need to see if the number of crtcs changes to determine
whether or not we need to upload the mclk table again. In practice
we don't currently upload the mclk table again after the initial load.
The only reason you would would be to add new states, e.g., for
arbitrary mclk setting which is not currently supported.
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
On CI, we need to see if the number of crtcs changes to determine
whether or not we need to upload the mclk table again. In practice
we don't currently upload the mclk table again after the initial load.
The only reason you would would be to add new states, e.g., for
arbitrary mclk setting which is not currently supported.
Acked-by: Jordan Lazare <Jordan.Lazare@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
We don't want side effects. If something fails, we rollback vq->is_le to
its previous value.
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Looks like a copy-paste bug. The value is used as an optimization and a
wrong value probably isn't causing any serious damage. Found when
porting this code to Windows.
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Since I maintain this driver as part of mac80211, add it to
the file list for mac80211; this helps submitters send it to
me instead of Kalle and also makes the build robot apply the
patches for it on the right tree for build attempts.
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
commit 0973128002
Author: Imre Deak <imre.deak@intel.com>
Date: Wed Feb 17 14:17:42 2016 +0200
drm/i915: Add helper to get a display power ref if it was already enabled
left the rpm wakelock assertions unbalanced if CONFIG_PM was disabled as
intel_runtime_pm_get_if_in_use() would return true without incrementing
the local bookkeeping required for the assertions.
Fixes: 0973128002 ("drm/i915: Add helper to get a display power ref if it was already enabled")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
CC: Mika Kuoppala <mika.kuoppala@intel.com>
CC: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1456434628-22574-1-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Imre Deak <imre.deak@intel.com>
(cherry picked from commit 135dc79efb)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
During system suspend we need to first disable power wells then
unitialize the display core. In case power well support is disabled we
did this in the wrong order, so fix this up.
Fixes: d314cd43 ("drm/i915: fix handling of the disable_power_well module option")
CC: stable@vger.kernel.org
CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1456778945-5411-1-git-send-email-imre.deak@intel.com
(cherry picked from commit 2622d79bd9)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
vmx.c writes the TSC_MULTIPLIER field in vmx_vcpu_load, but only when a
vcpu has migrated physical cpus. Record the last value written and
update in vmx_vcpu_load on any change, otherwise a cpu migration must
occur for TSC frequency scaling to take effect.
Cc: stable@vger.kernel.org
Fixes: ff2c3a1803
Signed-off-by: Owen Hofmann <osh@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Returning directly whatever copy_to_user(...) or copy_from_user(...)
returns may not do the right thing if there's a pagefault:
copy_to_user/copy_from_user return the number of bytes not copied in
this case, but ioctls need to return -EFAULT instead.
Fix up kvm on mips to do
return copy_to_user(...)) ? -EFAULT : 0;
and
return copy_from_user(...)) ? -EFAULT : 0;
everywhere.
Cc: stable@vger.kernel.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The MC74xx and EM74xx modules use different IDs by default, according
to the Lenovo EM7455 driver for Windows.
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
During DRAM initialization on certain ASpeed devices, an incorrect
bit (bit 10) was checked in the "SDRAM Bus Width Status" register
to determine DRAM width.
Query bit 6 instead in accordance with the Aspeed AST2050 datasheet v1.05.
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
In the final versions of the Porter board (called "PORTER_C") Renesas
decided to get rid of the Maxim Integrated MAX3355 OTG chip and didn't
add any other provision to differ the host/gadget mode, so we'll have to
remove no longer valid "renesas,enable-gpio" property from the HS-USB
device node. Hopefully, the earlier revisions of the board were never
seen in the wild...
Fixes: c794f6a09a ("ARM: shmobile: porter: add HS-USB DT support")
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
has written.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJW09boAAoJEEhZKYFQ1nG7CosH/jpLN6ulu+VQQ+EhZuotViCA
9+rKPUQfdh+Vp0w72nil1YiIYIfHazSR0srP7M4/KPAy2C7+5jeu7urHMk2sbLzG
ud7uHQVeo+zfPEs2PBG/UDFbvDoyFXnB0iGg4e4PGKXv4yDlTuSS8mCYOyC1T2mF
+4WfAyy+Y35B75SonK/p8s4LQzRGQier6pguLFRPzo19W3g68GfF2zJTW3wXU+0H
37pKcYvrHixPc43oknEADJNdaB9PD6FoJ46jDefBhIK9HQSaDDjB2XxkStLXVtij
zclTaEbtxvI0Ch1mDrCwqCZ7TuNrRjX8i8Wb5F1qnQFO9BUvdYiYIUtkU4KWEYo=
=v5pE
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-linus
Peter writes:
One bug-fix using ID wakeup, this bug is existed once this driver
has written.
Pull d_inode/d_flags race fix from Al Viro.
I love this fix. Not only does it fix the race in the dentry type
handling, it entirely gets rid of the nasty and subtle memory ordering
rules for d_type and d_inode, and replaces them with the basic dentry
locking rules (sequence numbers under RCU, d_lock elsewhere).
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
use ->d_seq to get coherency between ->d_inode and ->d_flags
The 'flags' parameter of the of_phy_connect() function wasn't described
in the kernel-doc comment...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now in sctp_remaddr_seq_show(), we use variable *tsp to get the param *v.
but *tsp is also used to traversal transport_addr_list, which will cover
the previous value, and make sctp_transport_put work on the wrong transport.
So fix it by adding a new variable to get the param *v.
Fixes: fba4c330c5 ("sctp: hold transport before we access t->asoc in sctp proc")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the member .cmp_addr of sctp_af_inet6, sctp_v6_cmp_addr should also check
the port of addresses, just like sctp_v4_cmp_addr, cause it's invoked by
sctp_cmp_addr_exact().
Now sctp_v6_cmp_addr just check the port when two addresses have different
family, and lack the port check for two ipv6 addresses. that will make
sctp_hash_cmp() cannot work well.
so fix it by adding ports comparison in sctp_v6_cmp_addr().
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mike Frysinger reported that his ptrace testcase showed strange
behaviour on parisc: It was not possible to avoid a syscall and the
return value of a syscall couldn't be changed.
To modify a syscall number, we were missing to save the new syscall
number to gr20 which is then picked up later in assembly again.
The effect that the return value couldn't be changed is a side-effect of
another bug in the assembly code. When a process is ptraced, userspace
expects each syscall to report entrance and exit of a syscall. If a
syscall number was given which doesn't exist, we jumped to the normal
syscall exit code instead of informing userspace that the (non-existant)
syscall exits. This unexpected behaviour confuses userspace and thus the
bug was misinterpreted as if we can't change the return value.
This patch fixes both problems and was tested on 64bit kernel with
32bit userspace.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: stable@vger.kernel.org # v4.0+
Tested-by: Mike Frysinger <vapier@gentoo.org>
Alexandre Belloni says:
====================
phy: micrel: fix issues with interrupt on atmel boards
Since the phy is not polled anymore, there were issues getting a link on the
sama5d* xplained boards.
I'm not too sure about were those fixes should go and I'm wondering whether the
first one shoud be made generic.
For the second one, I found the PHY_HAS_MAGICANEG flag that is not used and I
wondering whether this is related to that kind of issue. I had a quick look at
the history and could'nt find its use.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable auto negotiation on init to properly detect an already plugged
cable at boot.
At boot, when the phy is started, it is in the PHY_UP state.
However, if a cable is plugged at boot, because auto negociation is already
enabled at the time we get the first interrupt, the phy is already running.
But the state machine then switches from PHY_UP to PHY_AN and calls
phy_start_aneg(). phy_start_aneg() will not do anything because aneg is
already enabled on the phy. It will then wait for a interrupt before going
further. This interrupt will never happen unless the cable is unplugged and
then replugged.
It was working properly before 321beec504 (net: phy: Use interrupts when
available in NOLINK state) because switching to NOLINK meant starting
polling the phy, even if IRQ were enabled.
Fixes: 321beec504 (net: phy: Use interrupts when available in NOLINK state)
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At least on ksz8081, when getting back from power down, interrupts are
disabled. ensure they are reenabled if they were previously enabled.
This fixes resuming which is failing on the xplained boards from atmel
since 321beec504 (net: phy: Use interrupts when available in NOLINK
state)
Fixes: 321beec504 (net: phy: Use interrupts when available in NOLINK state)
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
