Merging in current state of Linus' tree to deal with merge conflicts and
build failures in vio.c after merge.
Conflicts:
drivers/i2c/busses/i2c-cpm.c
drivers/i2c/busses/i2c-mpc.c
drivers/net/gianfar.c
Also fixed up one line in arch/powerpc/kernel/vio.c to use the
correct node pointer.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
By moving dma_mask into pdev_archdata, and adding archdata to
struct of_device, it makes it possible to substitute of_device
with struct platform_device, which is a stepping stone to
removing the of_platform bus entirely.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1674 commits)
qlcnic: adding co maintainer
ixgbe: add support for active DA cables
ixgbe: dcb, do not tag tc_prio_control frames
ixgbe: fix ixgbe_tx_is_paused logic
ixgbe: always enable vlan strip/insert when DCB is enabled
ixgbe: remove some redundant code in setting FCoE FIP filter
ixgbe: fix wrong offset to fc_frame_header in ixgbe_fcoe_ddp
ixgbe: fix header len when unsplit packet overflows to data buffer
ipv6: Never schedule DAD timer on dead address
ipv6: Use POSTDAD state
ipv6: Use state_lock to protect ifa state
ipv6: Replace inet6_ifaddr->dead with state
cxgb4: notify upper drivers if the device is already up when they load
cxgb4: keep interrupts available when the ports are brought down
cxgb4: fix initial addition of MAC address
cnic: Return SPQ credit to bnx2x after ring setup and shutdown.
cnic: Convert cnic_local_flags to atomic ops.
can: Fix SJA1000 command register writes on SMP systems
bridge: fix build for CONFIG_SYSFS disabled
ARCNET: Limit com20020 PCI ID matches for SOHARD cards
...
Fix up various conflicts with pcmcia tree drivers/net/
{pcmcia/3c589_cs.c, wireless/orinoco/orinoco_cs.c and
wireless/orinoco/spectrum_cs.c} and feature removal
(Documentation/feature-removal-schedule.txt).
Also fix a non-content conflict due to pm_qos_requirement getting
renamed in the PM tree (now pm_qos_request) in net/mac80211/scan.c
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (44 commits)
vlynq: make whole Kconfig-menu dependant on architecture
add descriptive comment for TIF_MEMDIE task flag declaration.
EEPROM: max6875: Header file cleanup
EEPROM: 93cx6: Header file cleanup
EEPROM: Header file cleanup
agp: use NULL instead of 0 when pointer is needed
rtc-v3020: make bitfield unsigned
PCI: make bitfield unsigned
jbd2: use NULL instead of 0 when pointer is needed
cciss: fix shadows sparse warning
doc: inode uses a mutex instead of a semaphore.
uml: i386: Avoid redefinition of NR_syscalls
fix "seperate" typos in comments
cocbalt_lcdfb: correct sections
doc: Change urls for sparse
Powerpc: wii: Fix typo in comment
i2o: cleanup some exit paths
Documentation/: it's -> its where appropriate
UML: Fix compiler warning due to missing task_struct declaration
UML: add kernel.h include to signal.c
...
This patch eliminates the node pointer from struct of_device and the
of_node (or prom_node) pointer from struct dev_archdata since the node
pointer is now part of struct device proper when CONFIG_OF is set, and
all users of the old pointer locations have already been converted over
to use device->of_node.
Also remove dev_archdata_{get,set}_node() as it is no longer used by
anything.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The Microblaze implementations of get_user() and (MMU) put_user() evaluate
the address argument more than once. This causes unexpected side-effects for
invocations that include increment operators, i.e. get_user(foo, bar++).
This patch also removes the distinction between MMU and noMMU put_user().
Without the patch:
$ echo 1234567890 > /proc/sys/kernel/core_pattern
$ cat /proc/sys/kernel/core_pattern
12345
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
This reverts commit 39e0786d3c.
On request from microblaze developers, they are going to handle
this differently.
Signed-off-by: David S. Miller <davem@davemloft.net>
NET_IP_ALIGN defaults to 2, no need to override.
NET_SKB_PAD is now 64, which is much larger than microblaze's
L1_CACHE_SIZE so no need to override that either.
Signed-off-by: David S. Miller <davem@davemloft.net>
Microblaze cacheline length is configurable and current cpu
uses two cacheline length 4 and 8.
We are taking conservative maximum value to be sure that cacheline
alignment is satisfied for all cases.
Here is the calculation for cacheline lenght 8 32bit=4Byte values
which is corresponding with SHIFT 5.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Based on PowerPC patche 52142e756e
PowerPC description:
On platforms doing non-coherent DMA (4xx, 8xx, ...), it's important
that the kmalloc minimum alignment is set to the cache line size, to
avoid sharing cache lines between different objects, so that DMA to
one of the objects doesn't corrupt the other.
Signed-off-by: Michal Simek <monstr@monstr.eu>
This patch fix consistent code which had problems with consistent_free
function.
I am not sure if we need to call flush_tlb_all after it but it keeps
tlbs synced.
I added noMMU and MMU version together.
Uncached shadow feature is not tested.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Current implementation doesn't handle dcache_line_length
correctly that's why is better to use generic memcpy.
Cache optimized function could be good way howto improve
performance but must be based on benchmarking not blind
function like this.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Remove section mismatch - based on ppc aproach.
WARNING: vmlinux.o(.text+0x64834): Section mismatch in reference
from the function __pte_alloc_kernel() to the function .init.text:early_get_page()
The function __pte_alloc_kernel() references
the function __init early_get_page().
This is often because __pte_alloc_kernel lacks a __init
annotation or the annotation of early_get_page is wrong.
Signed-off-by: Michal Simek <monstr@monstr.eu>
This patch adds support for using the LL TEMAC Ethernet driver on
non-Virtex 5 platforms by adding support for accessing the Soft DMA
registers as if they were memory mapped instead of solely through the
DCR's (available on the Virtex 5).
The patch also updates the driver so that it runs on the MicroBlaze.
The changes were tested on the PowerPC 440, PowerPC 405, and the
MicroBlaze platforms.
Signed-off-by: John Tyner <jtyner@cs.ucr.edu>
Signed-off-by: John Linn <john.linn@xilinx.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new io big-endian function. They will be used
for uartlite and spi driver.
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
Here is small regression on dhrystone tests and I think
that on all benchmarking tests. It is due to better checking
mechanism in put_user macro
Signed-off-by: Michal Simek <monstr@monstr.eu>
This is the first patch which does uaccess unification.
I choosed to do several patches to be able to use bisect
in future if any fault happens.
Signed-off-by: Michal Simek <monstr@monstr.eu>
I found several problems for ll_temac driver and on system with WB.
This early fix should fix it. I will clean this patch before I will add
it to mainline
Signed-off-by: Michal Simek <monstr@monstr.eu>
This patch add core PREEMPT support for Microblaze.
I tried to trace it via tracers and I was able to see any output.
I also added low level debug functions to see if that code is called.
Signed-off-by: Michal Simek <monstr@monstr.eu>
This patch is based on powerpc patch
64f1650247
We did some cleanups and removed powerpc parts.
There is one new debug early listing function too.
Exclude function is only in Debug options.
We tested in on custom board.
Signed-off-by: Michal Simek <monstr@monstr.eu>
There are two parts of changes. The first is just enable
PCI in Makefiles and in Kconfig. The second is the rest of
missing files. I didn't want to add it with previous patch
because that patch is too big.
Current Microblaze toolchain has problem with weak symbols
that's why is necessary to apply this changes to be possible
to compile pci support.
Xilinx knows about this problem.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Add pci-bridge.h for Microblaze. It is based on powerpc header file.
My changes:
I removed PPC_ prefix from constants
Removed ppc64 specifis parts
Signed-off-by: Michal Simek <monstr@monstr.eu>
I need to use generic/iomap.h for PCI that's why is necessary
to include it and fix ioport_{map,unmap} functions.
Signed-off-by: Michal Simek <monstr@monstr.eu>
