Currently, if CONFIG_SCSI_HISI_SAS_DEBUGFS_DEFAULT_ENABLE is enabled, the
memory space used by DFX is allocated during device initialization, which
occupies a large number of memory resources. The memory usage before and
after the driver is loaded is as follows:
Memory usage before the driver is loaded:
$ free -m
total used free shared buff/cache available
Mem: 867352 2578 864037 11 735 861681
Swap: 4095 0 4095
Memory usage after the driver which include 4 HBAs is loaded:
$ insmod hisi_sas_v3_hw.ko
$ free -m
total used free shared buff/cache available
Mem: 867352 4760 861848 11 743 859495
Swap: 4095 0 4095
The driver with 4 HBAs connected will allocate about 110 MB of memory
without enabling debugfs.
Therefore, to avoid wasting memory resources, DFX memory is allocated
during dump triggering. The dump may fail due to memory allocation
failure. After this change, each dump costs about 10 MB of memory, and each
dump lasts about 100 ms.
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Link: https://lore.kernel.org/r/1694571327-78697-4-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, register information dump is performed via workqueue, regardless
of the trigger mode (automatic or manual). There is a delay in dumping
register through workqueue, the exact register information at trigger time
cannot be obtained.
Call register snapshot directly instead of through a workqueue.
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Link: https://lore.kernel.org/r/1694571327-78697-3-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored and
this typically results in resource leaks. To improve here there is a quest
to make the remove callback return void. In the first step of this quest
all drivers are converted to .remove_new() which already returns void.
hisi_sas_remove() returned zero unconditionally so this was changed to
return void. Then it has the right prototype to be used directly as remove
callback for the two hisi_sas drivers.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230518202043.261739-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
chenxiang <chenxiang66@hisilicon.com> says:
This series contain some fixes including:
- Grab sas_dev lock when traversing sas_dev list to avoid NULL
pointer
- Handle NCQ error when IPTT is valid
- Ensure all enabled PHYs up during controller reset
- Exit suspend state when usage count of runtime PM is greater than 0
https://lore.kernel.org/r/1679283265-115066-1-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bart Van Assche <bvanassche@acm.org> says:
It helps humans and the compiler if it is made explicit that SCSI host
templates are not modified. Hence this patch series that constifies most
SCSI host templates. Please consider this patch series for the next merge
window.
Link: https://lore.kernel.org/r/20230322195515.1267197-1-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make it explicit that the SCSI host template is not modified.
Acked-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20230322195515.1267197-42-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently we sync irq to avoid freeing task before using task in I/O
completion. After adding io_uring support, we need to do something similar
for poll queues. As the process of CQ entries on poll queue are protected
by spinlock cq->lock, we can use spin_lock() + spin_unlock() on cq->lock to
make sure that CQ entries are processed to completion and then the complete
queue is synced.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Link: https://lore.kernel.org/r/1678169355-76215-4-git-send-email-chenxiang66@hisilicon.com
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a module parameter to set how many queues are used for iopoll. Also
fill the interface mq_poll. For internal I/Os from libsas and libata we use
non-iopoll queue (queue 0) to deliver and complete them. But for internal
abort I/Os, just don't send them for poll queues.
There is still a risk associated as this sends internal abort commands to
non-iopoll queues which actually requires sending an internal abort command
to every queue. As a result, make the module parameter as "experimental"
for now.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Link: https://lore.kernel.org/r/1678169355-76215-3-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When CQ header dw3 SATA_DISK_ERR is set it means this SATA disk is in error
state and the current IPTT is invalid. An invalid IPTT does not correspond
to any slot.
In this scenario, new I/Os that delivered to disk will be rejected by the
controller and all I/Os remaining in the disk should be aborted, which we
add here with the sas_ata_device_link_abort() call.
In hisi_sas_abort_task() we don't want to issue a soft reset as it may
cause info to be lost in the target disk for the ATA EH autopsy. In this
case, just release resources - the disk won't return other I/Os normally
after NCQ Error, so this is safe.
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/1665998435-199946-4-git-send-email-john.garry@huawei.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the common libsas internal abort functionality.
In addition, this driver has special handling for internal abort timeouts -
specifically whether to reset the controller in that instance, so extend
the API for that.
Timeout is now increased to 20 * Hz from 6 * Hz.
We also retry for failure now, but this should not make a difference.
Link: https://lore.kernel.org/r/1647001432-239276-5-git-send-email-john.garry@huawei.com
Tested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The time of phyup not only depends on the controller but also the type of
disk connected. As an example, from experience, for some SATA disks the
amount of time from reset/power-on to receive the D2H FIS for phyup can
take upto and more than 10s sometimes. According to the specification of
some SATA disks such as ST14000NM0018, the max time from power-on to ready
is 30s.
Based on this the current timeout of phyup at 2s which is not enough. So
set the value as HISI_SAS_WAIT_PHYUP_TIMEOUT (30s) in
hisi_sas_control_phy().
For v3 hw there is a pre-existing workaround for a HW bug, being that we
issue a link reset when the OOB occurs but the phyup does not. The current
phyup timeout is HISI_SAS_WAIT_PHYUP_TIMEOUT. So if this does occur from
when issuing a phy enable or similar via hisi_sas_control_phy(), the
subsequent HW workaround linkreset processing calls hisi_sas_control_phy(),
but this will pend the original phy reset timing out, so it is safe.
Link: https://lore.kernel.org/r/1645703489-87194-3-git-send-email-john.garry@huawei.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some of the LLDDs which use libsas have their own definition of a struct
to hold TMF info, so add a common struct for libsas.
Also add an interim force phy id field for hisi_sas driver, which will be
removed once the STP "TMF" code is factored out.
Even though some LLDDs (pm8001) use a u32 for the tag, u16 will be adequate,
as that named driver only uses tags in range [0, 1024).
Link: https://lore.kernel.org/r/1645112566-115804-8-git-send-email-john.garry@huawei.com
Tested-by: Yihang Li <liyihang6@hisilicon.com>
Tested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It is possible that controller may become suspended between processing a
phyup interrupt and the event being processed by libsas. As such, we can't
ensure the controller is active when processing the phyup event - this may
cause the phyup event to be lost or other issues. To avoid any possible
issues, add pm_runtime_get_noresume() in phyup interrupt handler and
pm_runtime_put_sync() in the work handler exit to ensure that we stay
always active. Since we only want to call pm_runtime_get_noresume() for v3
hw, signal this will a new event, HISI_PHYE_PHY_UP_PM.
Link: https://lore.kernel.org/r/1639999298-244569-14-git-send-email-chenxiang66@hisilicon.com
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To help factor out code in future, it's useful to know if we're executing
an internal abort, so pass a pointer to the structure. The idea is that a
NULL pointer means not an internal abort.
Link: https://lore.kernel.org/r/1639579061-179473-4-git-send-email-john.garry@huawei.com
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove this include directive from code that does not use any functionality
from kernel/async.c.
Link: https://lore.kernel.org/r/20211129194609.3466071-13-bvanassche@acm.org
Reviewed-by: Daejun Park <daejun7.park@samsung.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Perform driver-specific SCSI device initialization in the designated SCSI
midlayer callback instead of relying on the libsas "device found" callback.
The SCSI midlayer .slave_alloc interface is called prior to sending any I/O
to the device.
Link: https://lore.kernel.org/r/1634041588-74824-2-git-send-email-john.garry@huawei.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
HISI_SAS_RESET_BIT means that the controller is being reset, and so the
name is a bit vague. Rename it to HISI_SAS_RESETTING_BIT.
Link: https://lore.kernel.org/r/1629799260-120116-4-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If an internal task abort timeout occurs, the controller has developed a
fault, and needs to be reset to be recovered.
When this occurs during error handling, the current policy is to allow
error handling to continue, and the inevitable nexus ha reset will handle
the required reset.
However various steps of error handling need to taken before this happens.
These also involve some level of HW interaction, which will also fail with
various timeouts.
Speed up this process by recording a HW fault bit for an internal abort
timeout - when this is set, just automatically error any HW interaction,
and essentially go straight to clear nexus ha (to reset the controller).
Link: https://lore.kernel.org/r/1623058179-80434-6-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For a clear nexus reset operation, the I_T nexus resets are executed
serially for each device. For devices attached through an expander, this
may take 2s per device; so, in total, could take a long time.
Reduce the total time by running the I_T nexus resets in parallel through
async operations.
Link: https://lore.kernel.org/r/1623058179-80434-3-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If an OOB event is received but the phy still fails to come up, a link
reset will be issued repeatedly at an interval of 20s until the phy comes
up.
Set a limit for link reset issue retries to avoid printing the timeout
message endlessly.
Link: https://lore.kernel.org/r/1623058179-80434-2-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The debugfs snapshot should be executed before the reset occurs to ensure
that the register contents are saved properly.
As such, it is incorrect to queue the debugfs dump when running a reset as
the reset will occur prior to the snapshot work item is handler.
Therefore, directly snapshot registers in the reset work handler.
Link: https://lore.kernel.org/r/1617709711-195853-5-git-send-email-john.garry@huawei.com
Signed-off-by: Jianqin Xie <xiejianqin@hisilicon.com>
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The debugfs code has been relocated to v3 hw driver, so delete unused
struct hisi_sas_hw function pointers snapshot_{prepare, restore}.
Link: https://lore.kernel.org/r/1617709711-195853-2-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The controller provides trace FIFO DFX tool to assist link fault debugging
and link optimization. This tool can be helpful when debugging link faults
without SAS analyzers. Each PHY has an independent trace FIFO interface.
The user can configure the trace FIFO tool of one PHY by using the
following six interfaces:
signal_sel: select signal group applies to different scenarios.
0x0: linkrate negotiation
0x1: Host 12G TX train
0x2: Disk 12G TX train
0x3: SAS PHY CTRL DFX 0
0x4: SAS PHY CTRL DFX 1
0x5: SAS PCS DFX
other: linkrate negotiation
dump_mask: The masked hardware status bit will not be updated.
dump_mode: determines how to dump data after trigger signal is generated.
0x0: dump forever
0x1: dump 32 data after trigger signal is generated
0x2: no more dump after trigger signal is generated
trigger_mode: determines the trigger mode, level or edge.
0x0: dump when trigger signal changed
0x1: dump when trigger signal's level equal to trigger_level
0x2: dump when trigger signal's level different from trigger_level
trigger_level: determines the trigger level.
trigger_msk: mask trigger signal
The user can get 32-byte values from hardware by reading the rd_data.
These values consitute the status record of the hardware at different time
points.
Link: https://lore.kernel.org/r/1611659068-131975-6-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the new libsas event notifiers API, which requires callers to
explicitly pass the gfp_t memory allocation flags.
Below are the context analysis for modified functions:
=> hisi_sas_bytes_dmaed():
Since it is invoked from both process and atomic contexts, let its callers
pass the gfp_t flags:
* hisi_sas_main.c:
------------------
hisi_sas_phyup_work(): workqueue context
-> hisi_sas_bytes_dmaed(..., GFP_KERNEL)
hisi_sas_controller_reset_done(): has an msleep()
-> hisi_sas_rescan_topology()
-> hisi_sas_phy_down()
-> hisi_sas_bytes_dmaed(..., GFP_KERNEL)
hisi_sas_debug_I_T_nexus_reset(): calls wait_for_completion_timeout()
-> hisi_sas_phy_down()
-> hisi_sas_bytes_dmaed(..., GFP_KERNEL)
* hisi_sas_v1_hw.c:
-------------------
int_abnormal_v1_hw(): irq handler
-> hisi_sas_phy_down()
-> hisi_sas_bytes_dmaed(..., GFP_ATOMIC)
* hisi_sas_v[23]_hw.c:
----------------------
int_phy_updown_v[23]_hw(): irq handler
-> phy_down_v[23]_hw()
-> hisi_sas_phy_down()
-> hisi_sas_bytes_dmaed(..., GFP_ATOMIC)
=> int_bcast_v1_hw() and phy_bcast_v3_hw():
Both are invoked exclusively from irq handlers. Pass GFP_ATOMIC.
Link: https://lore.kernel.org/r/20210118100955.1761652-12-a.darwish@linutronix.de
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Merge two commits that had dependencies on other 5.11 trees (the block
and the irq trees respectively).
- We reverted a megaraid_sas change in 5.10 due to missing block
layer plumbing. Now that this is in place, reinstate the change.
- The hisi_sas driver had a dependency on a driver core irq change
that went in through Thomas' tree.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As a performance enhancement, make the completion queue interrupts managed.
In addition, in commit bf0beec060 ("blk-mq: drain I/O when all CPUs in a
hctx are offline"), CPU hotplug for MQ devices using managed interrupts is
made safe. So expose HW queues to blk-mq to take advantage of this.
Flag Scsi_host.host_tagset is also set to ensure that the HBA is not sent
more commands than it can handle. However the driver still does not use
request tag for IPTT as there are many HW bugs means that special rules
apply for IPTT allocation.
Link: https://lore.kernel.org/r/1606905417-183214-6-git-send-email-john.garry@huawei.com
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Relocate all the debugfs code for DFX to v3 hw since no other versions
support it.
Link: https://lore.kernel.org/r/1606207594-196362-4-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This series consists of the usual driver updates (ufs, qla2xxx, tcmu,
ibmvfc, lpfc, smartpqi, hisi_sas, qedi, qedf, mpt3sas) and minor bug
fixes. There are only three core changes: adding sense codes,
cleaning up noretry and adding an option for limitless retries.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCX4YulyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishaZDAQCT7rwG
UEZYHgYkU9EX9ERVBQM0SW4mLrxf3g3P5ioJsAEAtkclCM4QsIOP+MIPjIa0EyUY
khu0kcrmeFR2YwA8zhw=
=4w4S
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"The usual driver updates (ufs, qla2xxx, tcmu, ibmvfc, lpfc, smartpqi,
hisi_sas, qedi, qedf, mpt3sas) and minor bug fixes.
There are only three core changes: adding sense codes, cleaning up
noretry and adding an option for limitless retries"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (226 commits)
scsi: hisi_sas: Recover PHY state according to the status before reset
scsi: hisi_sas: Filter out new PHY up events during suspend
scsi: hisi_sas: Add device link between SCSI devices and hisi_hba
scsi: hisi_sas: Add check for methods _PS0 and _PR0
scsi: hisi_sas: Add controller runtime PM support for v3 hw
scsi: hisi_sas: Switch to new framework to support suspend and resume
scsi: hisi_sas: Use hisi_hba->cq_nvecs for calling calling synchronize_irq()
scsi: qedf: Remove redundant assignment to variable 'rc'
scsi: lpfc: Remove unneeded variable 'status' in lpfc_fcp_cpu_map_store()
scsi: snic: Convert to use DEFINE_SEQ_ATTRIBUTE macro
scsi: qla4xxx: Delete unneeded variable 'status' in qla4xxx_process_ddb_changed
scsi: sun_esp: Use module_platform_driver to simplify the code
scsi: sun3x_esp: Use module_platform_driver to simplify the code
scsi: sni_53c710: Use module_platform_driver to simplify the code
scsi: qlogicpti: Use module_platform_driver to simplify the code
scsi: mac_esp: Use module_platform_driver to simplify the code
scsi: jazz_esp: Use module_platform_driver to simplify the code
scsi: mvumi: Fix error return in mvumi_io_attach()
scsi: lpfc: Drop nodelist reference on error in lpfc_gen_req()
scsi: be2iscsi: Fix a theoretical leak in beiscsi_create_eqs()
...
Now that the block layer provides a shared tag, we can switch the driver
to expose all HW queues.
Signed-off-by: John Garry <john.garry@huawei.com>
Tested-by: Douglas Gilbert <dgilbert@interlog.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Through the new debugfs interface the user can select fixed code
patterns. Add two new interfaces fixed_code and fixed_code1.
Link: https://lore.kernel.org/r/1598958790-232272-7-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add BIST support for phy FFE (Feed forward equalizer) setting. The user can
configure FFE through the new debugfs interface.
FFE is a parameter used for link layer control. It will affect the link
quality between the SAS controller and the backplane. In the BIST test, the
FFE interface is provided to assist board testers in optimizing link
parameters.
The modification of the FFE parameter will affect the test after BIST or
the normal running of the board. The user should save the initial FFE
values and restore them after BIST test is complete.
Link: https://lore.kernel.org/r/1598958790-232272-6-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently IRQ_EFFECTIVE_AFF_MASK is enabled for ARM_GIC and ARM_GIC3, so it
only allows a single target CPU in the affinity mask to process interrupts
and also interrupt thread, and the performance of using threaded irq is
almost the same as tasklet. But if the config is not enabled, the interrupt
thread will be allowed all the CPUs in the affinity mask. At that situation
it improves the performance (about 20%).
Note: IRQ_EFFECTIVE_AFF_MASK is configured differently for different
architecture chip, and it seems to be better to make it be configured
easily.
Link: https://lore.kernel.org/r/1579522957-4393-2-git-send-email-john.garry@huawei.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The number of phy down reflects the quality of the link between SAS
controller and disk. In order to allow the user to confirm the link quality
of the system, we record the number of phy down for each phy.
The user can check the current phy down count by reading the debugfs file
corresponding to the specific phy, or clear the phy down count by writing 0
to the debugfs file.
Link: https://lore.kernel.org/r/1571926105-74636-19-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We use the module parameter debugfs_dump_count to manage the upper limit of
the memory block for multiple dumps.
Link: https://lore.kernel.org/r/1571926105-74636-17-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We add multiple dumps for debugfs, but only allocate memory this time and
only dump #0.
Link: https://lore.kernel.org/r/1571926105-74636-15-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Create a file structure which was used to save the memory address for
ITCT cache at debugfs. This structure is bound to the corresponding debugfs
file, it can help callback function of debugfs file to get what it needs.
Link: https://lore.kernel.org/r/1571926105-74636-14-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Create a file structure which was used to save the memory address for IOST
cache at debugfs. This structure is bound to the corresponding debugfs
file, it can help callback function of debugfs file to get what it needs.
Link: https://lore.kernel.org/r/1571926105-74636-13-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Create a file structure which was used to save the memory address for ITCT
at debugfs. This structure is bound to the corresponding debugfs file, it
can help callback function of debugfs file to get what it needs.
Link: https://lore.kernel.org/r/1571926105-74636-12-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Create a file structure which was used to save the memory address for IOST
at debugfs. This structure is bound to the corresponding debugfs file, it
can help callback function of debugfs file to get what it needs.
Link: https://lore.kernel.org/r/1571926105-74636-11-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Create a file structure which was used to save the memory address and phy
pointer for port at debugfs. This structure is bound to the corresponding
debugfs file, it can help callback function of debugfs file to get what it
need.
Link: https://lore.kernel.org/r/1571926105-74636-10-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Create a file structure which was used to save the memory address and
hisi_hba pointer for REGS at debugfs. This structure is bound to the
corresponding debugfs file, it can help callback function of debugfs file
to get what it need.
Link: https://lore.kernel.org/r/1571926105-74636-9-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Create a file structure which was used to save the memory address and DQ
pointer for DQ at debugfs. This structure is bound to the corresponding
debugfs file, it can help callback function of debugfs file to get what it
need.
Link: https://lore.kernel.org/r/1571926105-74636-8-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Create a file structure which was used to save the memory address and CQ
pointer for CQ at debugfs. This structure is bound to the corresponding
debugfs file, it can help callback function of debugfs file to get what it
need.
Link: https://lore.kernel.org/r/1571926105-74636-7-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It's useful to know when the dump occurred, so add a timestamp file for
this.
Link: https://lore.kernel.org/r/1571926105-74636-6-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
