The legacy system PM support has long time ago been dropped from the
AMBA bus. Align to that by converting to the modern system PM
callbacks.
Fixes: 26825cfd90 (ARM: 7914/1: amba: Drop legacy PM support ...)
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
A big problem with the current i8042 debugging option is that it outputs
data going to and from the keyboard by default. As a result, many dmesg
logs uploaded by users will unintentionally contain sensitive information
such as their password, as such it's probably a good idea not to output
data coming from the keyboard unless specifically enabled by the user.
Signed-off-by: Stephen Chandler Paul <cpaul@redhat.com>
Reviewed-by: Andreas Mohr <andim2@users.sf.net>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The original wait time was 200ms which was enough for the firmware to
finish loading and boot. After that the firmware will perform
initialization and touch calibration, which will take about 1.1 second. The
touch calibration will change controller frequency to scan at the most
optimal frequency and during calibration/frequency switching process we may
run into i2c data errors. To avoid them we extend the sleep to 2500ms after
issuing the sw reset.
Signed-off-by: HungNien Chen <hn.chen@weidahitech.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
These attributes can be used to identify controllers present in the system.
Signed-off-by: HungNien Chen <hn.chen@weidahitech.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's switch to using standard touchscreen device properties parsing module
instead of doing it by hand in the driver.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
input_mt_init_slots() will perform necessary settings for performing
multi-touch to single-touch emulation, we do not need to do that ourselves.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The controller has a RESET pin which is usually controlled over
a GPIO line. If such a GPIO is provided, perform a RESET
during probe.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We are using threaded interrupt handler and thus are allowed to sleep.
Let's switch over to gpiod_get_value_cansleep() so that we do not get
ugly warnings in case GPIO controller might sleep when accessing GPIO.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This allows uniform parsing on legacy, DT and ACPI systems.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's move driver's platform data definitions from include/linux/input/
into include/linux/platform_data/ so that it stays with the rest of
platform data definitions.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's switch form OF to device properties so that common parsing code could
work not only on device tree but also on ACPI-based platforms.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The binding specification says that "touchscreen-size-x" and "-y" specify
horizontal and vertical resolution of the touchscreen and therefore maximum
absolute coordinates should be reduced by 1 since we are starting with 0.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Do issue warning about axis that is present in device tree but not specified
by the driver even in case of multi-touch axis as callers now tell us if they
expect multi-touch data or not.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use for_each_set_bit to check for set bits in bitmap
as it is more efficient and compact.
Signed-off-by: Anshul Garg <aksgarg1989@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use for_each_set_bit to check for set bits in bitmap
as it is more efficient than checking individual bits.
Signed-off-by: Anshul Garg <aksgarg1989@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use for_each_set_bit to check for set bits in bitmap as it is more
efficient than checking individual bits.
Signed-off-by: Anshul Garg <aksgarg1989@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
These reg_default tables are not modified after initialized, so make them
const.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use the new GPIO descriptor interface to handle the zForce GPIOs.
This simplifies the code and allows transparently handle GPIO polarity, as
specified in device tree data.
Also switch to using gpio_{set|get}_value_cansleep() since none of the
callers is in atomic context and cansleep variant allows more GPIO
controllers to be used with the touchscreen.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Despite it's name, sign_extend32() is used for 16 bit values aswell.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Get the scaling factor when it reads the sys params. The width value will
multiple the factor and report the value in the TOUCH_MAJOR event.
Signed-off-by: HungNien Chen <hn.chen@weidahitech.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fix this compile error:
drivers/built-in.o: In function `arc_ps2_probe':
/mnt/linux/drivers/input/serio/arc_ps2.c:206: undefined reference to `devm_ioremap_resource'
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This fixes the following warning:
drivers/input/touchscreen/wdt87xx_i2c.c: In function 'wdt87xx_validate_firmware':
>> drivers/input/touchscreen/wdt87xx_i2c.c:472:4: warning: format '%zd' expects argument of type 'signed size_t', but argument 4 has type 'size_t' [-Wformat=]
size, fw->size);
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When applying touchscreen parameters specified in device tree let's make
sure we keep whatever setup was done by the driver and not reset the
missing values to zero.
Reported-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
edt-ft5x06 is a touchscreen and thus a direct input device; let's amrk it
as such. This also allows us to drop some initialization code as
input_init_mt_slots() will do that for us.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of iterating over all bits in a bitmap and test them individually
let's siwtch to for_each_set_bit() which is more compact and is also
faster.
Also use bitmap_weight() when counting number of set bits.
This also fixes INPUT_DO_TOGGLE() implementation as it should have used
*_CNT as the upper boundary, not *_MAX.
Signed-off-by: Anshul Garg <aksgarg1989@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This is a driver for Weida HiTech WDT87xx series touchscreen controller.
Signed-off-by: HungNien Chen <hn.chen@weidahitech.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Currently we are reporting the button state as inverted on all boards with
an axp209 pmic, tested on a ba10-tvbox, bananapi, bananapro, cubietruck and
utoo-p66 tablet.
The axp209 datasheet clearly states that the power button must be connected
between the PWRON key and ground. Which means that on a press we will get
a falling edge (dbf) irq not a rising one, and likewise on release we will
get a rising edge (dbr) irq, not a falling one.
This commit swaps the check for the 2 irqs fixing the inverted reporting of
the power button state.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The controller only receives commands when its present. So for the
correct LED to be lit the LED command has to be sent on the present
event.
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Based on Patch by Pierre-Loup A. Griffais <pgriffais@valvesoftware.com>:
Add the logic to set the LEDs on XBox Wireless controllers. Command
sequence found by sniffing the Windows data stream when plugging the
device in.
Updated based on comments on linux-input:
unify codepaths in xpad_send_led_command for wired/ wireless controller.
Also document command values for clarification.
All values tested on Xbox 360 Wireless Controller.
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
clk_prepare_enable() may fail, so we should better check its return value
and propagate it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for
output. Simplify drivers accordingly.
Note that in the case of the drv260x driver error checking is more
strict now because -ENOSYS is reported to the caller now. But this
should only be returned if GPIOLIB is disabled which shouldn't happen as
the driver depends on GPIOLIB.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This change creates a new input handler called "leds" that exports LEDs on input
devices as standard LED class devices in sysfs and allows controlling their
state via sysfs or via any of the standard LED triggers. This allows to
re-purpose and reassign LDEs on the keyboards to represent states other
than the standard keyboard states (CapsLock, NumLock, etc).
The old API of controlling input LEDs by writing into /dev/input/eventX
devices is still present and will take precedence over accessing via LEDs
subsystem (i.e. it may override state set by a trigger). If input device is
"grabbed" then requests coming through LED subsystem will be ignored.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Tested-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use kernel.h macro definition.
Thanks to Julia Lawall for Coccinelle scripting support.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
input_mt_init_slots() will do that for us.
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Goodix touchscreens export through their registers a Product ID and
Firmware Version. The Product ID is an ASCII encoding of the product name
(e.g.: "911").
Export to sysfs (through the input subsystem) the product id and firmware
version read from the device rather than using constant values.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Acked-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fix sparse warning:
drivers/input/touchscreen/goodix.c:182:26: warning: Variable length array is used.
Replace the variable length array with fixed length.
Some Goodix devices have maximum 5 touch points, while others have 10 touch
points. Using the maximum length (80 bytes) for all devices will lead to
wasting 40 bytes on stack when using devices with maximum 5 touch points.
However, that is preferable to using kmalloc which will use even more
resources.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Acked-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds OnKey driver support for DA9063.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Previously the elan_i2c touchpad driver would simply request the firmware
"/lib/firmware/elan_i2c.bin", which does not work well if there are
multiple such devices in the system.
Let's append the "product ID" (by using the same function as the sysfs
interface for consistency) to the filename. This results in filenames of
the form "/lib/firmware/elan_i2c_72.0.bin", allowing you to support
multiple elan_i2c touchpads on the same device by simply naming each
device's FW with its corresponding product ID. This way when you trigger a
fw update the driver will load the correct binary.
Signed-off-by: Charlie Mooney <charliemooney@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In order to support multiple IC types for i2c/smbus protocol, add get ic
type command and use this data when checking firmware page count and
signature address.
Signed-off-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Focaltech touchpads report finger width in packet[5] of absolute packet.
Range for width in raw format is 0x10 - 0x70. Second half-byte is always 0.
0xff is reported, when a large contact area is detected.
This can be handled in userspace.
Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The variable no_decel is bool type so assigning "true" instead of "1".
Also, synaptics_i2c_get_input() has bool return type, so let's use "false"
there.
Signed-off-by: Shailendra Verma <shailendra.capricorn@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The variable psmouse_smartscroll is bool type so assigning true
instead of 1.
Signed-off-by: Shailendra Verma <shailendra.capricorn@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The STMPE MFD is only used with device tree configured systems (and STMPE
MFD core depends on OF), so force the configuration to come from device
tree only.
Tested-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When STMPE is instantiated via device tree individual MFD cells rae formed
with OF modaliases, not platform modaliases, and so we need to add OF
device table to the driver if we want it to load automatically:
of:Nstmpe_touchscreenT<NULL>Cst,stmpe-ts
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
rajeev-dlh.kumar@st.com email-id doesn't exist anymore as I have left the
company.
Signed-off-by: Rajeev Kumar <rajeevkumar.linux@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
gcc-5 defaults to gnu11 which used c99 inline semantics in c99 'inline' is
not externally visible unlike gnu89, therefore we use 'static inline' which
has same semantics between gnu89 and c99
Signed-off-by: Khem Raj <raj.khem@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The I2C subsystem can match devices without explicit OF support based on
the part of their compatible property after the comma. However, this
mechanism uses the first compatible value only. For adxl34x OF device
nodes the compatible property will contain the more specific
"adi,adxl345" or "adi,adxl346" value first. This prevents the device
node from being matched with the adxl34x driver.
Fix this by adding an OF match table with an "adi,adxl345" compatible
entry. There's no need to add the "adi,adxl346" entry as the ADXL346 is
backward-compatible with the ADXL345 with differences handled by runtime
detection of the device model.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>