This patch fixes faulty behaviour in a setup where the input clock for the
SRG is fed through the CLKR/CLKX pin but the McBSP is configured to be
master (SND_SOC_DAIFMT_CBS_CFS). In that case of course CLKR/CLKX must
not be configured as output pin. Otherwise the input clock is messed up
horribly.
This patch makes it possible to use the CLKR/CLKX pin rather than CLKS to
inject a reference clock in setups where McBSP is master and not both
rx and tx are used. However for this to work it has to be ensured that
set_dai_sysclk() is called after set_dai_fmt().
This was tested on a beagleboard-xm using McBSP1 to drive a i2s DAC through
the tx lines (CLKX,FSX,DX). Using this patch the CLKR pin is used to inject
an external reference clock.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the standard naming convention for the codec DAI.
Signed-off-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch corrects the routing paths of that after IF1/2 DACx Mux
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The struct dev_pm_ops defines usage_count only when CONFIG_PM is defined. So
we should use this variable only in cases where this falg is true.
So we define a local variable and read the value under this flag. In non PM
cases, we set this to 1.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some platforms, e.g. WSB, don't need jack detection when
system is in Suspend, for power save reason.
Here add headphone/mic jack detection disable feature with NULL
jack passed in, when disabled, it will disable interrupt, and
disable LDO1, which is used for jack detection when headphone
is plugged in.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Reviewed-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds snd_soc_of_parse_audio_routing() to get dapm routes
configurations via Device Tree.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The current helper functions, snd_soc_of_parse_audio_simple_widgets()
and snd_soc_of_parse_audio_routing(), set dapm_widgets and dapm_routes
without caring if they are already set by using build-in widgets and
routes in the card driver. So there could be one of them, build-in one
or Device Tree one, overrided by the other depending on which one was
assigned later.
This patch adds an extra pair of dapm_widgets and dapm_routes for DT
use only so as to prevent unexpected overriding.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When using non-standard rates, a relatively small amount of overclocking
can make a big difference to a number of cases.
- Not all rates are possible to achieve with the PLL, due to divider
restrictions.
- The higher oversampling rates that can be used by the DAC, the
simpler the analog output filters get (mirror frequencies move up,
away from the desired spectrum).
- The more work the DSP can perform per sample, the better.
For standard rates, there is little to gain as everything is
designed just right, and the needed overclocking to make a
real difference would be significant.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
The STA32X_AUTO3 is a writable register that currently does not appear
in the regmap ranges(neither read nor write). By adding this register
to the register ranges there is no gap anymore and the existing
register ranges can be joined. This fixes a regression introduced in
commit a1be4cead9 where the driver was
moved to direct regmap usage and the STA32X_AUTO3 register was missed.
That made it impossible to choose the preset EQ mode set through the
STA32X_AUTO3 register.
Fixes: a1be4cead9 (ASoC: sta32x: Convert to direct regmap API usage)
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for
output. Simplify drivers accordingly.
Also there is an *_optional variant that serves well here. The sematics
is slightly changed here by using it as error checking is more strict
now: If GPIOLIB is not enabled an error is returned instead of just
ignoring the gpio. On one hand this is bad for devices that don't "have"
the respective gpio as the driver is failing now. On the other hand
there is no means to assert that this gpio is really not needed or if
only the driver to control it is not available. The latter is a real
reason to fail and so it's defensive to fail here, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
RT5670_IRQ_CTRL1(0xbd) is a non volatile register. And we need to
restore its value after suspend/resume.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In our platform we want platform and codec driver routines to get invoked
and don't need the machine routines so remove here
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Thus removing the runtime_resume handler.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds support for system pm support. We need to save the dsp memory
which gets lost on suspend and restore that on resume
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Export 32-bit version of memcpy for use in suspend/resume.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds support for platform suspend and resume. We ensure all pcms are
suspended by invoking snd_soc_suspend() and then stop the DSP
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver didn't implement support for pcm stream suspend and resume, so
add it
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds missing pcm pause and resume ops in the driver
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The updated firmware expects the MMX ID to be used as 3, so update the
driver as well
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DSP messages are sent with nonatomic context, which include trigger
messages, so mark the driver as nonatomic
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ALSA core with commit 257f8cce5d - "ALSA: pcm: Allow nonatomic trigger
operations" allows trigger ops to implemented as nonatomic. For ASoC, we can
specify this in dailinks and is updated while snd_pcm is created
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
this patch will fix below sparse warnings
warning: incorrect type in argument 2 (different base types) expected
unsigned int [unsigned] val got restricted snd_pcm_format_t [usertype]
<noident>
sound/soc/intel/haswell.c:61:37
sound/soc/intel/broadwell.c:115:37:
sound/soc/intel/bytcr_dpcm_rt5640.c:118:37:
sound/soc/intel/cht_bsw_rt5672.c:183:37:
sound/soc/intel/cht_bsw_rt5645.c:208:37:
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The manual recommends that we reset the DSP when we suspend so add that in
runtime suspend handler
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The IPC driver saved only IMR register, we need to save the CSR as well, so
add it
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The updated firmware expects the MMX ID to be used as 3, so update the
driver as well
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Here are a few small fix patches for 3.20-rc1:
- Quirks for Denon and Lifecam USB-audio devices and HD-audio
on HP laptops
- A long-time regression fix for HDSP eMADI
- Add missing DRAIN_TRIGGER flag set for ASoC intel-sst
- Trivial fixes for sequencer core and HD-audio Tegra, a LINE6
cleanup
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=IYJ7
-----END PGP SIGNATURE-----
Merge tag 'sound-fix-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are a few small fix patches for 3.20-rc1:
- Quirks for Denon and Lifecam USB-audio devices and HD-audio on HP
laptops
- A long-time regression fix for HDSP eMADI
- Add missing DRAIN_TRIGGER flag set for ASoC intel-sst
- Trivial fixes for sequencer core and HD-audio Tegra, a LINE6
cleanup"
* tag 'sound-fix-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usb: Fix support for Denon DA-300USB DAC (ID 154e:1003)
ASoC: Intel: add SNDRV_PCM_INFO_DRAIN_TRIGGER flag
ALSA: usb-audio: Don't attempt to get Lifecam HD-5000 sample rate
ALSA: hda/tegra check correct return value from ioremap_resource
ALSA: hdspm - Constrain periods to 2 on older cards
ALSA: hda - enable mute led quirk for one more hp machine.
ALSA: seq: potential out of bounds in do_control()
ALSA: line6: Improve line6_read/write_data() interfaces
Add missing header files to avoid implicit
declarations and indirect inclusions.
Signed-off-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The tlv320aic23 codec is selected by the ep93xx snapper platform,
which are missing a dependency on I2C, and that can result in this
build error, as found during randconfig builds:
.../codecs/tlv320aic23-i2c.c: In function 'tlv320aic23_i2c_probe':
.../codecs/tlv320aic23-i2c.c:27:2: error: implicit declaration of function 'i2c_check_functionality' [-Werror=implicit-function-declaration]
if (!i2c_check_functionality(i2c->adapter, I2C_FUNC_SMBUS_BYTE_DATA))
^
This adds the missing dependency.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
A few sound drivers for the samsung platforms are missing dependencies
on I2C or SPI, which can lead to build errors like
codecs/rt5631.c:1737:1: warning: data definition has no type or storage class
31_i2c_driver);
codecs/rt5631.c:1737:1: error: type defaults to 'int' in declaration of 'module_i2c_driver' [-Werror=implicit-int]
codecs/rt5631.c:1737:1: warning: parameter names (without types) in function declaration
codecs/rt5631.c:1726:26: warning: 'rt5631_i2c_driver' defined but not used [-Wunused-variable]
I have gone through all the ones that did not already have
an I2C dependency and added the ones that I found missing,
namely arndale, odroid-x2, littlemill, bells and speyside
and this patch adds all the dependencies.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Whilst the existing code does correctly round to the next 4-byte boundary
it does so rather inefficiently. This patch changes the rounding to be
simpler and more efficient.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently DSP controls are persistent (across DSP On/Off) only
if they were set whilst the DSP is off. This change makes the
controls persistent irrespective of when they are set.
Signed-off-by: Nikesh Oswal <Nikesh.Oswal@wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We need to set left/right control for the speaker amp to get stereo
output on speaker.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, we will configure dmic related pin definition if pdata.dmic_en
is true. However, there is no disable option in the enum. So, any dmic is
used, all 3 dmic related pins will be configured. It may cause unexpected
pin definition. This patch adds a disable item for each dmic enum and
take it as default. So the driver will not set the pin configuration if
we don't set dmicx_data_pin in platform data.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull dmaengine updates from Vinod Koul:
"This update brings:
- the big cleanup up by Maxime for device control and slave
capabilities. This makes the API much cleaner.
- new IMG MDC driver by Andrew
- new Renesas R-Car Gen2 DMA Controller driver by Laurent along with
bunch of fixes on rcar drivers
- odd fixes and updates spread over driver"
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (130 commits)
dmaengine: pl330: add DMA_PAUSE feature
dmaengine: pl330: improve pl330_tx_status() function
dmaengine: rcar-dmac: Disable channel 0 when using IOMMU
dmaengine: rcar-dmac: Work around descriptor mode IOMMU errata
dmaengine: rcar-dmac: Allocate hardware descriptors with DMAC device
dmaengine: rcar-dmac: Fix oops due to unintialized list in error ISR
dmaengine: rcar-dmac: Fix spinlock issues in interrupt
dmaenegine: edma: fix sparse warnings
dmaengine: rcar-dmac: Fix uninitialized variable usage
dmaengine: shdmac: extend PM methods
dmaengine: shdmac: use SET_RUNTIME_PM_OPS()
dmaengine: pl330: fix bug that cause start the same descs in cyclic
dmaengine: at_xdmac: allow muliple dwidths when doing slave transfers
dmaengine: at_xdmac: simplify channel configuration stuff
dmaengine: at_xdmac: introduce save_cc field
dmaengine: at_xdmac: wait for in-progress transaction to complete after pausing a channel
ioat: fail self-test if wait_for_completion times out
dmaengine: dw: define DW_DMA_MAX_NR_MASTERS
dmaengine: dw: amend description of dma_dev field
dmatest: move src_off, dst_off, len inside loop
...
Add SNDRV_PCM_INFO_DRAIN_TRIGGER in snd_pcm_hardware.info to
call sst_hsw_stream_set_silence_start() when PCM draining.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ADSP on Braswell/Baytrail is an ACPI device. This patch sets its initial
runtime PM status to active. Otherwise, its initial status is suspended and
runtime_suspend ops will not be called after probe and thus cannot further
trigger ACPI _PS3 (D3) method to put the device into low power D3cold state.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch add a missing check on the return value of devm_kzalloc,
which would cause a NULL pointer dereference in a OOM situation.
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Support for setups where codec is bitclock slave and frame master.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes the following compilation errors:
sound/soc/codecs/max98357a.c: In function ‘max98357a_daiops_trigger’:
sound/soc/codecs/max98357a.c:30:3: error: implicit declaration of function ‘gpiod_set_value’ [-Werror=implicit-function-declaration]
sound/soc/codecs/max98357a.c: In function ‘max98357a_codec_probe’:
sound/soc/codecs/max98357a.c:55:2: error: implicit declaration of function ‘devm_gpiod_get’ [-Werror=implicit-function-declaration]
sound/soc/codecs/max98357a.c:61:2: error: implicit declaration of function ‘gpiod_direction_output’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Kenneth Westfield <kwestfie@codeaurora.org>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The max98357a driver depends on GPIOLIB. This may cause the following
build failure.
sound/soc/codecs/max98357a.c: In function 'max98357a_daiops_trigger':
sound/soc/codecs/max98357a.c:30:3: error: implicit declaration of function 'gpiod_set_value'
sound/soc/codecs/max98357a.c: In function 'max98357a_codec_probe':
sound/soc/codecs/max98357a.c:55:2: error: implicit declaration of function 'devm_gpiod_get'
sound/soc/codecs/max98357a.c:61:2: error: implicit declaration of function 'gpiod_direction_output'
Seen with mips:allmodconfig as well as various randconfig builds.
Fixes: af5adf1293 ("ASoC: max98357a: Add MAX98357A codec driver")
Cc: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
The BDW audio firmware DSP manages the DMA and the DMA cannot be
stopped exactly at the end of the playback stream. This means
stale samples may be played at PCM stop unless the driver copies
silence to the subsequent periods.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
According to i.MX Reference Manual, the bit-clock frequency generated
by SSI must be never greater than 1/5 of the peripheral clock frequency.
This peripheral clock, however, is not baudclk but the IPG clock (i.e.
ssi_private->clk in the fsl_ssi driver).
So this patch just simply fixes the incorrect limitation applied to
the bit clock (baudclk) rate.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the SSC acts as BCK master, use a ratnum rule to limit
the rate instead of only doing the standard rates. When the SSC
acts as BCK slave, allow any BCK frequency up to the SSC master
clock, divided by either of 2, 3 or 6.
Put a cap at 384kHz. Who's /ever/ going to need more than that?
The divider of 2, 3 or 6 is selected based on the Serial Clock Ratio
Considerations section from the SSC documentation:
The Transmitter and the Receiver can be programmed to operate
with the clock signals provided on either the TK or RK pins.
This allows the SSC to support many slave-mode data transfers.
In this case, the maximum clock speed allowed on the RK pin is:
- Peripheral clock divided by 2 if Receiver Frame Synchro is input
- Peripheral clock divided by 3 if Receiver Frame Synchro is output
In addition, the maximum clock speed allowed on the TK pin is:
- Peripheral clock divided by 6 if Transmit Frame Synchro is input
- Peripheral clock divided by 2 if Transmit Frame Synchro is output
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The analog audio is supported via omap-abe-twl6040 machine driver on
omap5-uevm.
Update the Kconfig file to reflect this and select the Palmas clock driver
which is providing the 32K clock for audio on omap5-uevm.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set device data before snd_soc_register_platform/component.
Otherwise, it will use NULL pointer if user calls unbind -> bind or
rmmod -> insmod
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A few more updates for v3.20 that have accumilated over the second half
of last week. One new (relatively simple) driver for the Maxim
max98357a and some other driver specific fixes and enhancements. I did
apply a few patches that haven't been in -next just now before sending
this, all fixes except for one simple device ID addition patch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU2F6pAAoJECTWi3JdVIfQ7qkH/RehUr+fH9XgnFH3fX6MoxCO
rXfAHziSa+zV8xDVvj4eIgsqwwQ1eF40qnvAdlNe+rBx8q0fA56YpJZhuvSmLoRh
PE+VAEMKp3dP87CxlTHfJRWSry22ijWkPUBqOry+bqAm8ZijaJI6HNG2/j7CJDgx
31gP4GDC5t0moNco2Pg5Aq2tcnAXfNKCzLs/2nr0iG2UXiXqArKHtHCBtLgVtyqb
KOpH+c01bKy1+83gMxc8pLH8TP1WGWmoFm9BIeLkmYBU4n6odTM8Wcmv7npu3HoO
BPZDcy+NsHQY/b85EPX/VFKdLrR+E6/EEvDW+4gVs1NTmu3G18SG81uKnoA6UYA=
=4I1/
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.20-3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Final updates for v3.20
A few more updates for v3.20 that have accumilated over the second half
of last week. One new (relatively simple) driver for the Maxim
max98357a and some other driver specific fixes and enhancements. I did
apply a few patches that haven't been in -next just now before sending
this, all fixes except for one simple device ID addition patch.
Nothing too exciting here yet, a small optimization for DAPM from
Lars-Peter and a few small bits and pieces for drivers but nothing
that really stands out.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUoX40AAoJECTWi3JdVIfQCHkH/20AXx65DLEvKjtKJTbhE25j
XSmN3ZtXuEdzg70rG1E2YZsZofxRWShX7HHyCwmepWfe30o+V4UCR+4HyHIWVLF6
O3TpupfcQ9ACP+/jQQxxySnTld6LJqW7rNXpxTVGeaba82uDtKIVgv/gHoUtEBDi
NfG0RoVcfpb0k52LWzijIDx4YxVCuIkPHLFqBP63S92XNgw7bc8zjMl65ayY43M+
obfD0ISIdEudmkyqNrQzuNtxl14wsYjzQ5VYqltW5kLaEQVtmD8Zp1bOVI3m0xhX
KY8zQnUUwA4+Cxs8aAm/NvczAZ/GyEQSIjTdUQZDXm0k6H81eya108SfxGvaMYI=
=DSaV
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.19-rc2' into asoc-linus
ASoC: Updates for v3.20
Nothing too exciting here yet, a small optimization for DAPM from
Lars-Peter and a few small bits and pieces for drivers but nothing
that really stands out.
# gpg: Signature made Tue 30 Dec 2014 00:15:48 HKT using RSA key ID 5D5487D0
# gpg: Oops: keyid_from_fingerprint: no pubkey
# gpg: key AF88CD16: no public key for trusted key - skipped
# gpg: key AF88CD16 marked as ultimately trusted
# gpg: key 5621E907: no public key for trusted key - skipped
# gpg: key 5621E907 marked as ultimately trusted
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
RT5670 doesn't support auto incrementing writes so driver should
set the use_single_rw flag for regmap.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
sound/soc/intel/cht_bsw_rt5645.c:315:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current snd_soc_unregister_card() indicates unregistered debug
message when it was called. But, it should be called only when
it was really unregistered.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Removes some functions that are not used anywhere:
sst_hsw_stream_unmute() sst_hsw_stream_mute() msg_set_stage_type()
sst_hsw_dx_get_state() sst_hsw_stream_set_write_position()
sst_hsw_stream_get_vol_reg() sst_hsw_stream_get_peak_reg()
sst_hsw_stream_get_pointer_reg() sst_hsw_stream_get_read_reg()
sst_hsw_stream_get_mixer_id() sst_hsw_stream_get_hw_id()
sst_hsw_mixer_set_volume_curve() sst_hsw_mixer_unmute()
sst_hsw_mixer_mute() sst_hsw_stream_set_volume_curve()
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
Function sst_acpi_probe() uses plain strcpy for setting member firmware_name
of a struct intel_sst_drv from member firmware of a struct sst_machines.
Thereby the destination array has got a length of 20 byte while the source may
hold 32 byte. Since eg. commit 64b9c90b86 ("ASoC: Intel: Fix BYTCR firmware
name") increased strings from "fw_sst_0f28.bin" to "intel/fw_sst_0f28.bin"
there is an actual possibility that the 20 byte array at the end of struct
intel_sst_drv is overrun.
Thus increase the size of the destination and use the same define for both
structs. Detected by Coverity CID 1260087.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Commit 28c8331d38 ("ARM: S5PV210: Remove support for board files")
removed the Kconfig symbols MACH_GONI and MACH_AQUILA. As a result the
dependencies of SND_SOC_GONI_AQUILA_WM8994 can never be met. So remove
the unbuildable "SoC I2S Audio support for AQUILA/GONI - WM8994".
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add codec driver for the Maxim MAX98357A DAC.
Signed-off-by: Kenneth Westfield <kwestfie@codeaurora.org>
Acked-by: Banajit Goswami <bgoswami@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
These are rather too large for this late in the release cycle but
they're clear, well understood and have been tested to fix a regression
which was introduced for v3.19. The details are all in Lars' changelog
and they've been cooking in -next for a while, to a large extent out
of conservatism about the size.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU08iuAAoJECTWi3JdVIfQ9cUH/1ZNkoS67zEj/wsvcS+co/Dp
hInq7mAwO/usFfFWMzb68Lofc4g5yTGE+vtTAhggmzMGuqjXEMCAS/tO85EoA65d
2f0YNw7gEhUyp0oYPe5tS3I0F8O7ES+u27PwmM8sGO0KdCc9qrb3ppZN3BkEcr2U
akg854atOcKwBvGRLNSyj79WPkjNyMcM/kWkJCEHFLysu8rSilZ+UaekH+CUw02E
hstLM+PlM0LE/9rKmQvRyx6cnVqKqPWxalG0mCtBwpdHLYMn4yDFc3nn71lMn3oQ
/TIcHSfDCRgx3VVW8daBjNHqLgfg4XCcZ5W646zrpyyrlXRCCPJT8N0SY9jZUU4=
=ScU7
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-ac97-v3.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: AC'97 fixes
These are rather too large for this late in the release cycle but
they're clear, well understood and have been tested to fix a regression
which was introduced for v3.19. The details are all in Lars' changelog
and they've been cooking in -next for a while, to a large extent out
of conservatism about the size.
Another one liner that arrived after the earlier pull request. There's
a trivial conflict with my -next branch, I'll send a pull request with
that resolution and some other new stuff before Monday.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU09ESAAoJECTWi3JdVIfQZ+oH/10mjezNacUT0hFqZsNTQyFq
bG1pnU/szkZeMaP0Y1/fHawwgafOcGOPCU6DYDiN7KnNLdCdMW9slxSyZhigD+kV
G/eopUu0hPQOvlqq+ODGQ3eJ92kBefXzv5v4ophnqeaCdJm+uZbWqvPykVDp8Tqq
Og7R7AXX9BncCvLCiwhl9KCfKu61DViuCMLWNSbOkoZcRReMeRny0dXLG9WXWx3U
db72KflC4TZ5i8miKXAqTW/HHLhT8AL+v+B/3I8h/cDCRY6MvkU2qYE01Yvboull
RJMNuANKgMCVkEnp9izVzGXT/cUTCF6YCQSaPbUkSDWhbTOwirgF7BJBRir1xdM=
=vv5N
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-intel-v3.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fix for Intel firmware name
Another one liner that arrived after the earlier pull request. There's
a trivial conflict with my -next branch, I'll send a pull request with
that resolution and some other new stuff before Monday.
All sst firmware is provided under the intel directory of the linux-firmware
tree. By default this directory structure is kept when installing on a target
system. Change the path to expect a default linux-firmware installation.
Signed-off-by: Kevin Strasser <kevin.strasser@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch add the customize setting for Dell Dino project.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We assign rt286->codec in rt286_probe. If rt286_jack_detect is
invoked before rt286_probe, rt286->codec will be NULL and cause
a kernel panic.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
All sst firmware is provided under the intel directory of the linux-firmware
tree. By default this directory structure is kept when installing on a target
system. Change the path to expect a default linux-firmware installation.
Signed-off-by: Kevin Strasser <kevin.strasser@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add machine driver for two Intel Cherryview-based platforms, Cherrytrail
and Braswell, with RT5645 codec
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Kevin Strasser <kevin.strasser@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch defines an API to select the clock source for specified filters.
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Acked-by: Kevin Strasser <kevin.strasser@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For runtime suspend/resume, it is some different with suspend/resume,
e.g. codec power supply won't be switch off, codec jack detection
still working(to wake up system from Jack event), won't call call
snd_soc_suspend/resume, etc.
So here, we add a platform PM status, HSW_PM_STATE_RTD3, to make
the status more clear, when in idle, it will enter this status, to
transfer from HSW_PM_STATE_RTD3 to HSW_PM_STATE_D3, we will do those
extra jobs, and vice versa for resuming.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
More updates for v3.20:
- Lots of refactoring from Lars-Peter Clausen, moving drivers to more
data driven initialization and rationalizing a lot of DAPM usage.
- Much improved handling of CDCLK clocks on Samsung I2S controllers.
- Lots of driver specific cleanups and feature improvements.
- CODEC support for TI PCM514x and TLV320AIC3104 devices.
- Board support for Tegra systems with Realtek RT5677.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU0ok8AAoJECTWi3JdVIfQ3ccH/2zb+b477H4GNhUw5AEzdHtC
L7CI+5Q9VOGJQmZTjayRdUcPUHx4sTpYdQVTI56Q6CJk0OFljKNJcRrbzPqNgJ46
yOrMTIpNvzFEv46f7rX2uKfvAFOVRAA2f+gl34AMLXqxL5aydbZZBtoe2jP9lL8z
fIZ/s7qXHn3xnvxqNwOz3pnu6wFDrxbG34lXZaTaFQOueZ3fsthWLsz0xtO6a7aI
J9tA+wejd9qf+D3i6svsi+MhB6OehYMh9Fbm+ODj6NMWZGCIA3SJ/PD+gbCg318+
Xo0FNOyiw0fSAeBcHrEcfoaWBJrswxXjXaNbrIXc1/0gTj8AOJHCRus3w0OQU+Q=
=Yw2l
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v3.20
More updates for v3.20:
- Lots of refactoring from Lars-Peter Clausen, moving drivers to more
data driven initialization and rationalizing a lot of DAPM usage.
- Much improved handling of CDCLK clocks on Samsung I2S controllers.
- Lots of driver specific cleanups and feature improvements.
- CODEC support for TI PCM514x and TLV320AIC3104 devices.
- Board support for Tegra systems with Realtek RT5677.
Conflicts:
sound/soc/intel/sst-mfld-platform-pcm.c
This patch adds device tree support for the jz4740 driver.
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The div clock register is not modified during jz4740_i2s_hw_params.
Hence, default sampling rates are actually used regardless of
sampling rates input from userspace.
This patch adds support to calculate the value of the divider from
the parameters passed from userspace and update the relevant div
registers
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
this patch fixes following sparse warning:
ts3a227e.c:222:5: warning: symbol 'ts3a227e_enable_jack_detect' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Reported by Coverity: CID 1267985 CID 1267986
Fix these two Defects: Uninitialized scalar variable.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The intercon_extra_3104 is obviously for tlv320aic3104.
Reported-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To quote from section 1.3.1 of the data sheet:
The SGTL5000 has an internal reset that is deasserted
8 SYS_MCLK cycles after all power rails have been brought
up. After this time, communication can start
...
1.0us represents 8 SYS_MCLK cycles at the minimum 8.0 MHz SYS_MCLK.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Disables GPIO support and LINE2 input and renames Mic3 input to Mic2,
if tlv320aic3104 mode is seleced. Devicetree binding document is
updated accordingly.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of calling device_create_file() manually, assign the static
attribute group entries at the device registration. This simplifies
the error handling and avoids the possible races.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Added entry in sst driver to support rt5645 codec
for intel Braswell platform.
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Renesas R-Car sound driver is using snd_ctl_xxx()
functions, but it didn't call snd_ctl free_one() / snd_ctl_remove().
This patch call these functions.
Reported-by: Nguyen Viet Dung <nv-dung@jinso.co.jp>
Reported-by: Bui Duc Phuc <bd-phuc@jinso.co.jp>
Reported-by: Cao Minh Hiep <cm-hiep@jinso.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
One of the McASP instances in DM646x line of DMSoC only supports DIT mode.
This means that the given IP does not have support for rx and all the rx
related resources are missing, like irq and DMA request.
The driver should not fail if any or all of the RX resource is missing
when the op_mode is set to DIT mode.
Since RX is not possible in DIT mode, we can just ignore the rx resources
when the McASP is used in DIT mode.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On DA830 devices McASP0,1 and 2 shares a single combined interrupt request
line.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The machine driver has no business with the underlying dma.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Like previous patches, at this time we embed the struct device into
PCM object. However, this needs a bit more caution: struct snd_pcm
doesn't own one device but two, for both playback and capture! Thus
not struct snd_pcm but struct snd_pcm_str object contains the device.
Along with this change, pcm->dev field is dropped for avoiding
confusion. It was meant to point to a non-standard parent. But,
since now we can touch each struct device directly, we can manipulate
the parent field easily there, too.
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As DMA framework request DMA using direction only in prep_slave
function, (The At91 xdma driver has adapted to this request).
So won't check direction when do DMA configuration.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In startup function, enable ssc clock and in shutdown function,
disable clock. And also remove disable ssc in shutdown function,
as ssc is disabled in prepare function.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When SCC work in DSP A mode, the data outputs/inputs are shift out on
falling edge, the frame sync are sample on the rising edge.
Reported-by: Songjun Wu <songjun.wu@atmel.com>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Shift the I2S mode value by the necessary amount before writing the
registers. This makes Right Justified and PCM mode work in addition to
the default Left Justified mode.
Signed-off-by: Filip Brozovic <fbrozovic@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the issue introduced by:
3684940933 ASoC: tlv320aic3x: Add TDM support
The CTRLC register were not receiving the correct delay configuration,
which will corrupt DSP_A audio mode.
Fixes: 3684940933 (ASoC: tlv320aic3x: Add TDM support)
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
"Mic Bias" is DAPM_SUPPLY so it has to be connected in the route
accordingly.
Fixes audio capture on the board.
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
In a rare combination of Kconfig settings, the 88pm860x-codec
module may be selected as a loadable module, while it's also being
used by the ttb-dkb code that is built-in, resulting in a link
error:
sound/built-in.o: In function `ttc_pm860x_init':
:(.text+0x3e888): undefined reference to `pm860x_hs_jack_detect'
:(.text+0x3e898): undefined reference to `pm860x_mic_jack_detect'
Changing ttb-tkb to a tristate option tells Kconfig that 88pm86x
actually needs to be built-in if ttc-dkb is also built-in.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This was overlooked in the late change to remove the I2S padding bits
from S24_LE mode. The patch also limits S32_LE mode to 384kHz, the
maximum according to the datasheets.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
The rt5677 codec has gained code that requires SPI to work correctly,
but there is no provision in Kconfig to prevent the driver from
being used when SPI is disabled or a loadable module, resulting
in this build error:
sound/built-in.o: In function `rt5677_spi_write':
:(.text+0xa7ba0): undefined reference to `spi_sync'
sound/built-in.o: In function `rt5677_spi_driver_init':
:(.init.text+0x253c): undefined reference to `spi_register_driver'
ERROR: "spi_sync" [sound/soc/codecs/snd-soc-rt5677-spi.ko] undefined!
ERROR: "spi_register_driver" [sound/soc/codecs/snd-soc-rt5677-spi.ko] undefined!
This makes the SPI portion of the driver depend on the SPI subsystem,
and disables the function that uses SPI for firmware download if SPI
is disabled. The latter may not be the correct solution, but I could
not come up with a better one.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: af48f1d08a ("ASoC: rt5677: Support DSP function for VAD application")
Signed-off-by: Mark Brown <broonie@kernel.org>
An earlier bug fix of mine made the SND_DM365_VOICE_CODEC symbol
tristate to avoid creating an undefined reference from the
davinci-vcif.c driver to the davinci_soc_platform_register
function that may be in a module.
However, this may now lead to a different error on randconfig
kernels:
"warning: SND_DM365_VOICE_CODEC creates inconsistent choice state"
This happens because we now have a choice statement with
one bool and one tristate option, and the latter might not
support being set to 'y' because of dependencies.
This new change turns the other option into 'tristate' as well,
which avoids the problem.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 19926c6de0 ("ASoC: davinci: vcif must be a module if SND_DAVINCI_SOC is")
Signed-off-by: Mark Brown <broonie@kernel.org>
The WM8904 and WM8918 has the same data type, while the WM8912
has different data type. So, use the data in dt ids table to
distinguish them.
Signed-off-by: Alexander Morozov <linux@meltdown.ru>
[voice.shen@atmel.com: add code to distinguish device type]
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The PLL introduces jitter, which in turn introduces noice if used
to clock the DAC. Thus, avoid the PLL output, and use the PLL input
to drive the DAC clock, if possible.
This is described for the PCM5142/PCM5242 chips in the answers to the
forum post "PCM5142/PCM5242 DAC clock source" at the TI E2E community
pages (1).
(1) http://e2e.ti.com/support/data_converters/audio_converters/f/64/t/389994
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
Using the PLL in master mode requires using an external connection
between one of the GPIO pins (configured as PLL/4 output) and the
SCK pin. It also requires the external clock to be fed to some other
GPIO pin instead of the SCK pin.
This is described for the PCM5122 chip in the answers to the forum post
"PCM5122 DAC as I2S master troubles with PLL mode" at the TI E2E
community pages (1). The clocking functionality is also much better
described in the datasheet for the chip PCM5242, which seems to be
register compatible with PCM512x and PCM514x (which both have severely
lacking datasheets).
(1) http://e2e.ti.com/support/data_converters/audio_converters/f/64/t/267830
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use register field names from the seemingly compatible PCM5242 datasheet,
as the PCM512x and PCM514x datasheets are severly lacking.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
of_match_ptr is already conditionally compiled based on
CONFIG_OF so further conditional compilation is not
required. Remove conditional compilation surrounding
of_match_ptr.
Signed-off-by: Andrew Jackson <Andrew.Jackson@arm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We never set the ->scratch pointer, so let's delete it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fix warning while "make xmldocs".
Warning(.//sound/soc/soc-devres.c:70): No description
found for parameter 'platform_drv'
Warning(.//sound/soc/soc-devres.c:70): Excess function
parameter 'platform' description in 'devm_snd_soc_register_platform'
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We need hold lock each time updating shirm registers, otherwise,
we may set unexpected values to them when they are set in
different thread at different time sequence.
The notification work will be scheduled in global work queue,
which won't hold this sst->spinlock itself, so here we need
change to use the lock version to update shim registers.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The I2C init path forgot to init the mutex, leading to an oops when
controls are accessed.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
As the clock can be get from TK/RK pin, so remove the comments.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to the I2S specification information as following:
- WS = 0, channel 1 (left)
- WS = 1, channel 2 (right)
So, the start event should be TF/RF falling edge.
Reported-by: Songjun Wu <songjun.wu@atmel.com>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Save a bit of scheduling by coalescing all the output power up delays
into a single delay.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Give the output disable sequence a chance to fully complete, otherwise
there is a danger we may remove the clock before it is finished
resulting in a pop noise. The delay for each output must be cumulative
and these are coalesced into a single delay.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
- Add description for the driver
- Add dependency on the I2C module
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
make the sta32x driver usable with device tree configs. Code is heavily based
on the sta350 driver.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The reset GPIO on the STA32X Codecs is used to reset the Codec and clear
all registers. Also taking it down puts the IC in power save mode, so
we put the device in reset mode when we go to sleep.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
use the regmap API directly rather than relying on the snd_soc_read/write
functions as this seems to be in accordance with common practice.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The IDE bit in the CONFF register is the third bit not the fourth.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Asus T100TAF uses ACPI ID "10EC5642" for its audio codec. I suppose it is
updated ACPI ID for the RT5642 codec since some earlier platforms are using
"10EC5640" with the RT5642 too.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The purpose of rt286_adc_event is to mute/numnte the ADC mixer.
However, it will also set the capture volume to default value.
As a result, "ADC0 Capture Volume" is not working if it is set
before capture start. This patch remove rt286_adc_event and add
"ADC0 Capture Switch" to mute/unmute ADC mixer.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The wm97xx touchscreen driver binds itself to the snd_ac97 device that gets
registered by the CODEC driver and expects that the device has already been
reset. Before commit 6794f709b7 ("ASoC: ac97: Drop delayed device
registration") the device was only registered after the probe function of
the CODEC driver had finished running, but starting with the mentioned
commit the device is registered as soon as snd_soc_new_ac97_codec() is
called. This causes the touchscreen driver to no longer work. Modify the
CODEC drivers to use snd_soc_alloc_ac97_codec() instead of
snd_soc_new_ac97_codec() and make sure that the AC'97 device is reset before
the snd_ac97 device gets registered.
Fixes: 6794f709b7 ("ASoC: ac97: Drop delayed device registration")
Reported-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Manuel Lauss <manuel.lauss@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
In some cases it is necessary to before additional operations after the
device has been initialized and before the device is registered. This can
for example be resetting the device.
This patch introduces a new function snd_soc_alloc_ac97_codec() which is
similar to snd_soc_new_ac97_codec() except that it does not register the
device. Any users of snd_soc_alloc_ac97_codec() are responsible for calling
device_add() manually.
Fixes: 6794f709b7 ("ASoC: ac97: Drop delayed device registration")
Reported-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
regmap is a library function that gets selected by drivers that need it. No
driver modules should depend on it, since this can create dependency loops.
E.g. if machine driver depends on REGMAP_I2C and selects the CODEC driver
and the CODEC driver selects REGMAP_I2C, then the machine driver selects by
extension one of its dependencies.
The proper way to handle this is for machine drivers to depend on the same
dependencies as the CODEC driver they select. In this case it is I2C.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The "MicIn" widget is a card level DAPM element so pass the card's DAPM
context instead of the CODEC's DAPM context to snd_soc_dapm_disable_pin().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
All DAPM input and output pins of the wm8750 are either used in the card's
DAPM routing table or are marked as not connected.
Set the fully_routed flag of the card instead of manually marking the unused
inputs and outputs as not connected. This makes the code a bit shorter and
cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should select FSR also to be driven by McBSP, not only FSX.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
In soc_new_compress() when rtd->dai_link->dynamic is set, we create the pcm
substreams with this call:
ret = snd_pcm_new_internal(rtd->card->snd_card, new_name, num,
1, 0, &be_pcm);
which passes 0 as capture_count leading to
be_pcm->streams[SNDRV_PCM_STREAM_CAPTURE].substream
being NULL, hence when trying to set rtd a few lines below we get an oops.
Fix by using rtd->dai_link->dpcm_playback and rtd->dai_link->dpcm_capture as
playback_count and capture_count to snd_pcm_new_internal().
Signed-off-by: Qais Yousef <qais.yousef@imgtec.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
There are no more users of this field left so it can finally be removed.
New users should use snd_soc_dapm_to_codec(w->dapm);
The reason why it is removed is because it doesn't fit to well anymore in
the componentized ASoC hierarchy, where DAPM works on the snd_soc_component
level. And the alternative of snd_soc_dapm_to_codec(w->dapm) typically
generates the same amount of code, so there is really no reason to keep it.
For automatic conversion the following coccinelle semantic patch can be used:
// <smpl>
@@
struct snd_soc_dapm_widget *w;
@@
-w->codec
+snd_soc_dapm_to_codec(w->dapm)
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit f6b2a04590 ("ASoC: pxa: mioa701_wm9713: Convert to table based DAPM
setup") converted the driver to register the board level DAPM elements with
the card's DAPM context rather than the CODEC's DAPM context. The change
overlooked that the speaker widget event callback accesses the widget's
codec field which is only valid if the widget has been registered in a CODEC
DAPM context. This patch modifies the callback to take an alternative route
to get the CODEC.
Fixes: f6b2a04590 ("ASoC: pxa: mioa701_wm9713: Convert to table based DAPM
setup")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Call clk_prepare_enable() and clk_disable_unprepare() for cpu dai
clock and codec dai clock in dai statup and shutdown callbacks. This
to make sure the related clock are enabled when the audio device is
used.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current R-Car sound driver calls SRC -> SSI -> DVC functions,
but, it should be DVC -> SRC -> SSI.
Otherwise, SSI (= interface of codec) will have underrun error
when playback.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current DMA starts after SSI, and stops before SSI. but we need
to reverse these order. Otherwise, under/over run error might happen.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSI interrupt handler of R-Car sound driver will be called
when DIRQ (= Data read/write timing for PIO) or
UIRQ / OIRQ (= under/over run error).
DIRQ "interrupt" doesn't occur when DMA transfer, but then,
DIRQ "status bit" might occur. we need to ignore this DIRQ
operation when DMA. Otherwise, driver will push/pop as PIO.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current SRC/SSI output its error, but it desn't indicate
port number. it is un-understandable.
Let's indicate port number for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver has rsnd_mod_to_priv() macro, and struct rsnd_mod
has struct rsnd_priv pointer. But, it is waste of memory from data
structure point of view.
Today we can link mod <-> io <-> rdai each other, so saving priv in
rdai is very reasonable.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver's function requests rdai, but it is not used.
Adding priv is more reasonable. Let's replace it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver's many functions requests struct rsnd_dai (= rdai),
but, 1) we can get rdai from rsnd_io_to_rsnd(), 2) almost all rdai
is not used. Let's remove these rdai.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver can use rsnd_io_to_rdai()
we can get play/capture direction via io now.
Let's replace rsnd_dai_is_play() to rsnd_io_is_play()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver request rdai in everywhere, but each mod should
reach to rdai by itself. this patch adds missing rsnd_io_to_rdai().
io = rsnd_mod_to_io(mod);
rdai = rsnd_io_to_rdai(io);
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_dai_get_platform_info() is not used. Let's remove it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_dai_id() was not used. Let's remove it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
struct rsnd_dai is called as "rdai", and struct snd_soc_dai is called
as "dai" on this driver. but macro/function have confusable naming.
This patch rename rsnd_dai_is_clk_master() to rsnd_rdai_is_clk_master()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
struct rsnd_dai is called as "rdai", and struct snd_soc_dai is called
as "dai" on this driver. but macro/function have confusable naming.
This patch rename rsnd_dai_get() to rsnd_rdai_get()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver's mod (= ssi/src/dvc) have each own clk,
but, these are needed to start/stop each mod.
This patch adds struct clk in rsnd_mod, and start/stop these
via rsnd_mod_hw_start/stop() macro
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_ssi::rate is not used. Let's remove it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is only one I2S I/F, AD/DA path must operate to the same
format.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The stream_hw_id for System stream is 0x0, if we use initial stream_hw_id
value 0, it may return wrong(not committed) stream when calling function
get_stream_by_id() with stream_id=0. Here initial stream_hw_id to invalid
value to fix this issue.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds clock provider (currently only for DT platforms) for
the CODECLKO (CDCLK) gate, RCLKSRC mux and RCLK pre-scaler divider
divider clock. Those all tree clock are only available in the IIS
Multi Audio Interface (I2S0), the regular IIS Bus Interface has only
CDCLK gate clock.
The motivation behind this patch is to expose the I2S internal clocks
which are currently controlled through set_sysclk() through the clk
API, so dedicated sound machine driver per each board can be avoided.
The intention is also to fix the CDCLK gating issue reported by
Daniel Drake:
http://mailman.alsa-project.org/pipermail/alsa-devel/2014-September/081753.html
This patch also reverts commit b97c60abf9
("ASoC: samsung-i2s: Maintain CDCLK settings across i2s_{shutdown/
startup}") The problem that commit attempted to solve only affects
the Odroid X2/U3, which doesn't configure the CDCLK clock in
struct snd_soc_dai_ops hw_params callback and the issue should be
now resolved by using clk API, i.e. having the codec enabling/
disabling the CDCLK clock as required.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In order to support old DTs we check the codec device node if it
contains "clocks" property and only if it doesn't (which indicates
an old DT) we proceed with enabling the CDCLK clock by means of
the set_sysclk() callback. For new DTs which use the common clock
bindings for CDCLK that clock is supposed to be handled outside
the sound machine driver.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Ensure the I2SMOD, I2SPSR registers, which are also exposed through
clk API are only accessed with the i2s->spinlock spinlock held.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It seems this driver hasn't been updated for SMP, as local_irq_save/
local_irq_restore don't provide proper protection of read/modify/write
of the device's registers on such systems. Introduce a spinlock
serializing access to the register region, it will be helpful later
when I2SMOD, I2SPSR registers are made also accessible through the
clk API.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The usage of this goto seems unjustified, use if/else statement instead.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The code to get pointer to the other DAI is repeated multiple
times. Add a helper function and use it instead.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The clk_prepare_enable() call on the "iis" clock is moved to happen earlier
in the DAI platform device driver's probe() callback, so the I2S registers
can be safely accessed through the clk API, after the clk supplier is
registered in the platform device probe().
After this patch the "iis" clock is kept enabled since the (primary) I2S
platform device probe() and until the platform device driver remove() call.
This is similar to gating the clock in the snd_soc_dai probe() and remove()
callbacks.
Normally, in addition to that we should mark the device as PM runtime active,
so if runtime PM is enabled it can idle the device by turning off the clock.
Correcting this issue is left for a separate patch series, as we need to
ensure the BUSCLK clock is always enabled when required.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Acquire the I2S interface clock in driver probe() callback
as it's a per-device not a per-DAI clock. While at it switch
to the resource managed clk_get().
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The memory mapped registers region is common for both DAIs so request
it in the I2S platform device driver's probe for the platform device
corresponding to the primary DAI, rather than in the ASoC DAI's probe
callback. While at it switch to devm_ioremap_resource(). This also
drops the hard coded (0x100) register region size in the driver.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These functions may fail so let's properly report any errors.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Tidy up the samsung_i2s_get_driver_data() function by using
IS_ENABLE() instead of #ifdef and add missing braces for
the 'else' part. Also ensure we are not dereferencing NULL
'match' pointer.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When we want to use wm8960 codec, we should enable its MCLK in machine driver.
It's reasonable for wm8960 codec driver to manage its own MCLK.
When current bias_level is SND_SOC_BIAS_ON, it is preparing for a transition
away from ON. In this case, disable the codec mclk. When current bias_level
is not SND_SOC_BIAS_ON, it preparing for a transition to ON. In this case,
enable the codec mclk.
Signed-off-by: Zidan Wang <b50113@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There have been some conflicting interpretations of how
snd_soc_dai_set_tdm_slot() is supposed to work. This patch updates the
documentation to be more specific on the exact semantics to avoid such
problems in the future.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that the fsl DAI drivers uses the same semantics as the rest of a ASoC
the custom fsl_asoc_xlate_tdm_slot_mask() callback can be removed as it is
identical to the generic one.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The fsl-ssi and imx-ssi drivers use inverted semantics for the tx_mask and
rx_mask parameter of the set_tdm_slot() callback compared to rest of ASoC.
This patch updates the driver's semantics to be consistent with the rest of
ASoC, i.e. a set bit means a active slot and a cleared bit means a inactive
slot. This will allow us to use the set_tdm_slot() API in a more generic
way.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The mc13783 driver uses inverted semantics for the tx_mask and rx_mask
parameter of the set_tdm_slot() callback compared to rest of ASoC. This
patch updates the driver's semantics to be consistent with the rest of ASoC,
i.e. a set bit means a active slot and a cleared bit means a inactive slot.
This will allow us to use the set_tdm_slot() API in a more generic way.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Correct the path name for mux to get rid of the following warning:
--->8---
wm8904 1-001a: Control not supported for path ADCL -> [Left] -> AIFOUTL
wm8904 1-001a: ASoC: no dapm match for ADCL --> Left --> AIFOUTL
wm8904 1-001a: ASoC: Failed to add route ADCL -> Left -> AIFOUTL
wm8904 1-001a: Control not supported for path ADCR -> [Right] -> AIFOUTL
wm8904 1-001a: ASoC: no dapm match for ADCR --> Right --> AIFOUTL
wm8904 1-001a: ASoC: Failed to add route ADCR -> Right -> AIFOUTL
wm8904 1-001a: Control not supported for path ADCL -> [Left] -> AIFOUTR
wm8904 1-001a: ASoC: no dapm match for ADCL --> Left --> AIFOUTR
wm8904 1-001a: ASoC: Failed to add route ADCL -> Left -> AIFOUTR
wm8904 1-001a: Control not supported for path ADCR -> [Right] -> AIFOUTR
wm8904 1-001a: ASoC: no dapm match for ADCR --> Right --> AIFOUTR
wm8904 1-001a: ASoC: Failed to add route ADCR -> Right -> AIFOUTR
wm8904 1-001a: Control not supported for path AIFINR -> [Right] -> DACL
wm8904 1-001a: ASoC: no dapm match for AIFINR --> Right --> DACL
wm8904 1-001a: ASoC: Failed to add route AIFINR -> Right -> DACL
wm8904 1-001a: Control not supported for path AIFINL -> [Left] -> DACL
wm8904 1-001a: ASoC: no dapm match for AIFINL --> Left --> DACL
wm8904 1-001a: ASoC: Failed to add route AIFINL -> Left -> DACL
wm8904 1-001a: Control not supported for path AIFINR -> [Right] -> DACR
wm8904 1-001a: ASoC: no dapm match for AIFINR --> Right --> DACR
wm8904 1-001a: ASoC: Failed to add route AIFINR -> Right -> DACR
wm8904 1-001a: Control not supported for path AIFINL -> [Left] -> DACR
wm8904 1-001a: ASoC: no dapm match for AIFINL --> Left --> DACR
wm8904 1-001a: ASoC: Failed to add route AIFINL -> Left -> DACR
---8<---
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SOC_AT91SAM9X5 option is going to be removed, only depend on ARCH_AT91 like
for the other drivers.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the card owner field to avoid getting a kernel crash when the imx-spdif
is unloaded while the playback is active.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the slot_width "25" support in the TDM mode for the Intel platform.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch uses the regmap functions instead of the snd_soc functions in some
cases.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If asoc_simple_card_probe() fails, asoc_simple_card_unref() may be
called before dev_set_drvdata(), causing a NULL pointer dereference in
asoc_simple_card_unref():
Unable to handle kernel NULL pointer dereference at virtual address 000000d4
...
PC is at asoc_simple_card_unref+0x14/0x48
LR is at asoc_simple_card_probe+0x3d4/0x40c
This typically happens because asoc_simple_card_parse_of() returns
-EPROBE_DEFER, but other failure modes are possible.
devm_snd_soc_register_card()/snd_soc_register_card() may fail either
before or after dev_set_drvdata().
Pass a snd_soc_card pointer instead of a platform_device pointer to
asoc_simple_card_unref() to fix this.
Note that if CONFIG_OF_DYNAMIC=n, of_node_put() is a dummy, and gcc may
optimize away the loop over card->dai_link, never actually dereferencing
card, and thus avoiding the crash...
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: e512e001da ("ASoC: simple-card: Fix the reference count of device nodes")
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Since commit 2ffa531078 ("ASoC: fsl_ssi: Fix module unbound") the irq
number is retrieved via platform_get_irq(), which may fail and return a negative
number, so adapt its type to 'int'.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The following crash happens when trying to unload the snd_soc_imx_wm8962 module
while playback is active:
[ 208.666868] Unable to handle kernel paging request at virtc
[ 208.674110] pgd = 80004000
[ 208.676867] [7f06541c] *pgd=4c334811, *pte=00000000, *ppte=00000000
[ 208.683211] Internal error: Oops: 80000007 [#1] SMP ARM
[ 208.688445] Modules linked in: snd_soc_wm8962 snd_soc_fsl_ssi snd_soc_imx_audmux imx_pcm_fiq evbug]
...
In order to avoid such problem, fill the card owner field as suggested by
Lars-Peter Clausen:
"But looking at the source it seems that this is a core feature of ALSA and at
least for the card module itself it will do the ref-counting when a stream is
started/stopped. And we even support setting the owner of a card in ASoC.
It's just that pretty much no ASoC card driver bothers to set the owner field
in the snd_soc_card struct. So this particular problem can be fixed by updating
the imx-wm8962 driver to set the owner field."
By doing as suggested, we no longer see the crash when attempting to unload the
snd_soc_imx_wm8962 module while playback is active:
$ modprobe -r snd_soc_imx_wm8962
modprobe: can't unload module snd_soc_imx_wm8962: Resource temporarily
unavailable
Reported-by: Jiada Wang <jiada_wang@mentor.com>
Suggested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
L/R channel will be switched if under/over flow error happen on
Renesas R-Car sound device by the HW bugs. Then, HW restart is required
for salvage. This patch add salvage support for SRC.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DAC powerdown bit is managed by DAPM. Manually powering down the DAC in
the CODEC probe function may cause unnecessary power state transitions which
can lead to click and pop noises.
So leave the DAC powerdown bit in its default poweron-reset state and let
DAPM do all the management.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
All DAPM input and output pins of the wm8750 are either used in the card's
DAPM routing table or are marked as not connected.
Set the fully_routed flag of the card instead of manually marking the unused
inputs and outputs as not connected. This makes the code a bit shorter and
cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
All DAPM input and output pins of the wm9712 are either used in the card's
DAPM routing table or are marked as not connected.
Set the fully_routed flag of the card instead of manually marking the unused
inputs and outputs as not connected. This makes the code a bit shorter and
cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
All DAPM input and output pins of the uda1380 are either used in the card's
DAPM routing table or are marked as not connected.
Set the fully_routed flag of the card instead of manually marking the unused
inputs and outputs as not connected. This makes the code a bit shorter and
cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
All DAPM input and output pins of the ak4641 are either used in the card's
DAPM routing table or are marked as not connected.
Set the fully_routed flag of the card instead of manually marking the unused
inputs and outputs as not connected. This makes the code a bit shorter and
cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
All DAPM input and output pins of the wm9705 are either used in the card's
DAPM routing table or are marked as not connected.
Set the fully_routed flag of the card instead of manually marking the unused
inputs and outputs as not connected. This makes the code a bit shorter and
cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
All DAPM input and output pins of the wm9705 are either used in the card's
DAPM routing table or are marked as not connected.
Set the fully_routed flag of the card instead of manually marking the unused
inputs and outputs as not connected. This makes the code a bit shorter and
cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
All DAPM input and output pins of the wm8994 are either used in the card's
DAPM routing table or are marked as not connected.
Set the fully_routed flag of the card instead of manually marking the unused
inputs and outputs as not connected. This makes the code a bit shorter and
cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The "Headset Mic 2" and the "Headset Stereophone" widget are managed by the
jack detection logic. Their will be set depending on whether something is
connected to the jack or not. There is no need to manually change the state
beforehand as it will be overwritten anyway.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DSP programs are listed out of order.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The patch modified the behavior that updates the PLL parameter. It set the
update bit before the PLL power up.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There may be 2 pcm streams for a same DAI at most, and these 2
streams should have different hsw_pcm_data, e.g. they have
different persistent data, so here we need split hsw_pcm_data
for playback and capture, to make sure they won't be mixed
and keep cleaned.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
XTFPGA boards provides an audio subsystem that consists of TI CDCE706
clock synthesizer, I2S transmitter and TLV320AIC23 audio codec.
I2S transmitter has MMIO-based interface that resembles that of the
OpenCores I2S transmitter. I2S transmitter is always a master on I2S
bus. There's no specialized audio DMA, sample data are transferred to
I2S transmitter FIFO by CPU through memory-mapped queue interface.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch adds the MICBIAS VDD setting in the platform data. It can be set to
1V8 or 3V3 in the MICBIAS VDD.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the error message uses 'np->full_name' which leads to a very verbose
log that contains the full path of the node.
We can have a concise log by using pdev->name instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the error message uses 'np->full_name' which leads to a very verbose
log that contains the full path of the node.
We can have a concise log by using pdev->name instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the error message uses 'np->full_name' which leads to a very verbose
log that contains the full path of the node.
We can have a concise log by using pdev->name instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the error message uses 'np->full_name' which leads to a very verbose
log that contains the full path of the node.
We can have a concise log by using pdev->name instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the error message uses 'np->full_name' which leads to a very verbose
log as:
fsl-ssi-dai 202c000.ssi: no irq for node /soc/aips-bus@02000000/spba-bus@02000000/ssi@0202c000
We can have a concise log by using pdev->name instead:
fsl-ssi-dai 202c000.ssi: no irq for node 202c000.ssi
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A DAI may have 2 streams(playback/capture) and different modules
may be needed for them respectively, so we need add a stream
direction here, the combination(dai_id + stream) can tell us
which module we really need here.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The first 512 bytes of data DRAM memory is used for FW dump,
and this first data SRAM block should be never power gated
(always on), here always enable the block(DSRAM[0]) for D0
stage.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 2ffa531078 ("ASoC: fsl_ssi: Fix module unbound") changed the way to
retrieve the irq number from irq_of_parse_and_map() to platform_get_irq(), but
missed to updated the irq error check accordingly.
We should test for negative irq number and propagate it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch introduces the use of function put_unaligned_be16.
This is done using Coccinelle and semantic patch used is as follows:
@a@
typedef u16, __be16, uint16_t;
{u16,__be16,uint16_t} e16;
identifier tmp;
expression ptr;
expression y,e;
type T;
@@
- tmp = cpu_to_be16(y);
<+... when != tmp
(
- memcpy(ptr, (T)&tmp, \(2\|sizeof(u16)\|sizeof(__be16)\|sizeof(uint16_t)\|sizeof(e16)\));
+ put_unaligned_be16(y,ptr);
|
- memcpy(ptr, (T)&tmp, ...);
+ put_unaligned_be16(y,ptr);
)
...+>
? tmp = e
@@ type T; identifier a.tmp; @@
- T tmp;
...when != tmp
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
--
Changes Since v2:
Make the patch compatible for current code
sound/soc/codecs/wm5102.c | 6 +++---
1 file changed, 3 insertions(+), 3 deletions(-)
Signed-off-by: Mark Brown <broonie@kernel.org>
Export snd_soc_runtime_set_dai_fmt() so it can be used in modules.
Fixes: ce64c8b9cf ("ASoC: Add helper function for changing the DAI link format")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver supports NVIDIA Tegra Ryu board
Sponsored: Google ChromeOS
Signed-off-by: Anatol Pomozov <anatol.pomozov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use snd_soc_runtime_set_dai_fmt() to configure the format for the DAI link
rather than configuring each DAI individually.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use snd_soc_runtime_set_dai_fmt() to configure the format for the DAI link
rather than configuring each DAI individually.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For some setups it is necessary to change the DAI link format at runtime.
This patch factors out the code that does the initial static DAI link format
configuration into a separate helper function which can be used board
drivers as well.
This allows board drivers that have to change the DAI link format at runtime
to reuse it instead of having to manually change the format on all DAIs.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
On Cherrytrail and Braswell, the I2S BCLK is 100FS which cannot be supported
by RT5672 in slave mode and can cause noise. This patch selects codec ASRC
clock source to track I2S1 clock so that codec ASRC can be enabled to suppress
the noise.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Reviewed-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When codec is in slave mode, ASRC can suppress noise for asynchronous
MCLK and LRCLK or special I2S format. This patch defines an API to select
the clock source for specified filters. And the codec driver will turn on ASRC
for these filters if ASRC is selected as their clock source.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The previous definition of registers 0x84 and 0x85 doesn't match the datasheet.
So this patch removes the wrong definition and writes a new one for the two
registers.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should not send IPC stream commands to FW when the stream is
NULL, dereference the NULL pointer may also occur without precheck.
Here add NULL pointer checks for these stream APIs.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The 'gpios' field in 'struct i2s' is now unused, this change
seems to be missing in commit 0429ffeff4
("ASoC: samsung: Remove obsolete GPIO based DT pinmuxing").
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The only user of the async I/O support in ASoC is SPI which was using it to
avoid needless context thrashing and minimise controller runtime PM bounces.
The SPI framework has now been enhanced so that even normal spi_sync() calls
won't suffer these effects so we don't need to handle this in ASoC and in
fact it can be more efficient not to since we don't need to set up and tear
down the buffers needed to manage asynchronous I/O.
The async completions that DAPM does are left in place so drivers can use
them, they are very cheap if there is no asynchronous work queued.
Signed-off-by: Mark Brown <broonie@kernel.org>
A mach/ header is included but never used. Simply remove it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
wm8960 codec can't support sample rate 11250, it must be 11025.
Signed-off-by: Zidan Wang <b50113@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Set the dai_fmt field in the dai_link struct instead of manually calling
snd_soc_dai_fmt(). This makes the code cleaner and shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the dai_fmt field in the dai_link struct instead of manually calling
snd_soc_dai_fmt(). This makes the code cleaner and shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the dai_fmt field in the dai_link struct instead of manually calling
snd_soc_dai_fmt(). This makes the code cleaner and shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the dai_fmt field in the dai_link struct instead of manually calling
snd_soc_dai_fmt(). This makes the code cleaner and shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the dai_fmt field in the dai_link struct instead of manually calling
snd_soc_dai_fmt(). This makes the code cleaner and shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the dai_fmt field in the dai_link struct instead of manually calling
snd_soc_dai_fmt(). This makes the code cleaner and shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the dai_fmt field in the dai_link struct instead of manually calling
snd_soc_dai_fmt(). This makes the code cleaner and shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the dai_fmt field in the dai_link struct instead of manually calling
snd_soc_dai_fmt(). This makes the code cleaner and shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the dai_fmt field in the dai_link struct instead of manually calling
snd_soc_dai_fmt(). This makes the code cleaner and shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the dai_fmt field in the dai_link struct instead of manually calling
snd_soc_dai_fmt(). This makes the code cleaner and shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the dai_fmt field in the dai_link struct instead of manually calling
snd_soc_dai_fmt(). This makes the code cleaner and shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the dai_fmt field in the dai_link struct instead of manually calling
snd_soc_dai_fmt(). This makes the code cleaner and shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the dai_fmt field in the dai_link struct instead of manually calling
snd_soc_dai_fmt(). This makes the code cleaner and shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the dai_fmt field in the dai_link struct instead of manually calling
snd_soc_dai_fmt(). This makes the code cleaner and shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the dai_fmt field in the dai_link struct instead of manually calling
snd_soc_dai_fmt(). This makes the code cleaner and shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the dai_fmt field in the dai_link struct instead of manually calling
snd_soc_dai_fmt(). This makes the code cleaner and shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the dai_fmt field in the dai_link struct instead of manually calling
snd_soc_dai_fmt(). This makes the code cleaner and shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the dai_fmt field in the dai_link struct instead of manually calling
snd_soc_dai_fmt(). This makes the code cleaner and shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the dai_fmt field in the dai_link struct instead of manually calling
snd_soc_dai_fmt(). This makes the code cleaner and shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the dai_fmt field in the dai_link struct instead of manually calling
snd_soc_dai_fmt(). This makes the code cleaner and shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the dai_fmt field in the dai_link struct instead of manually calling
snd_soc_dai_fmt(). This makes the code cleaner and shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ALSA core takes care that all preallocated memory is freed when the PCM
itself is freed. There is no need to do this manually in the driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Board level DAPM elements should be registered with the card's DAPM context
rather than the CODEC's DAPM context.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To work properly snd_soc_dapm_ignore_suspend() needs to be called on
endpoint widgets. In this case those are the board level Speaker and
Headphone widgets and not the CODEC output widgets that are connected to
them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DAPM widgets are enabled by default, there is no need to enable them unless
they have previously been explicitly disabled.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
