OTG3 and EH Compliance Plan 1.0 talks about Super Speed OTG Verification
system (SS-OVS) which consists of an excersizer and analyzer.
USB Compliance Suite from Lecroy or Ellisys can act as such SS-OVS for
Link Layer Validation (LVS).
Some modifications are needed for an embedded Linux USB host to pass all
these tests. Most of these tests require just Link to be in U0. They do
not work with default Linux USB stack since, default stack does port
reset and then starts sending setup packet, which is not expected by
Link Layer Validation (LVS) device of Lecroy Compliance Suit. Then,
There are many Link Layer Tests which need host to generate specific
traffic.
This patch supports specific traffic generation cases. As of now all the
host Lecroy Link Layer-USBIF tests (except TD7.26) passes
with this patch for single run using Lecroy USB Compliance Suite
Version 1.98 Build 239 and Lecroy USB Protocol Analyzer version 4.80
Build 1603. Therefore patch seems to be a good candidate for inclusion.
Further modification can be done on top of it.
lvstest driver will not bind to any device by default. It can bind
manually to a super speed USB host controller root hub. Therefore, regular
hub driver must be unbound before this driver is bound. For example, if
2-0:1.0 is the xhci root hub, then execute following to unbind hub driver.
echo 2-0:1.0 > /sys/bus/usb/drivers/hub/unbind
Then write Linux Foundation's vendor ID which is used by root hubs and
SS root hub's device ID into new_id file. Writing IDs into new_id file
will also bind the lvs driver with any available SS root hub interfaces.
echo "1D6B 3" > /sys/bus/usb/drivers/lvs/new_id
Now connect LVS device with root hub port.
Test case specific traffic can be generated as follows whenever needed:
1. To issue "Get Device descriptor" command for TD.7.06:
echo > /sys/bus/usb/devices/2-0\:1.0/get_dev_desc
2. To set U1 timeout to 127 for TD.7.18
echo 127 > /sys/bus/usb/devices/2-0\:1.0/u1_timeout
3. To set U2 timeout to 0 for TD.7.18
echo 0 > /sys/bus/usb/devices/2-0\:1.0/u2_timeout
4. To issue "Hot Reset" for TD.7.29
echo > /sys/bus/usb/devices/2-0\:1.0/hot_reset
5. To issue "U3 Entry" for TD.7.35
echo > /sys/bus/usb/devices/2-0\:1.0/u3_entry
6. To issue "U3 Exit" for TD.7.36
echo > /sys/bus/usb/devices/2-0\:1.0/u3_exit
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_alloc_dev is used by lvstest driver now which can be built as
module. Therefore export usb_alloc_dev symbol.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a bug in ohci-hcd. When an URB is unlinked, the
corresponding Endpoint Descriptor is added to the ed_rm_list and taken
off the hardware schedule. Once the ED is no longer visible to the
hardware, finish_unlinks() handles the URBs that were unlinked or have
completed. If any URBs remain attached to the ED, the ED is added
back to the hardware schedule -- but only if the controller is
running.
This fails when a controller dies. A non-empty ED does not get added
back to the hardware schedule and does not remain on the ed_rm_list;
ohci-hcd loses track of it. The remaining URBs cannot be unlinked,
which causes the USB stack to hang.
The patch changes finish_unlinks() so that non-empty EDs remain on
the ed_rm_list if the controller isn't running. This requires moving
some of the existing code around, to avoid modifying the ED's hardware
fields more than once.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The debug routine fill_async_buffer() in ohci-hcd is buggy: It never
produces any output because it forgets to initialize the output buffer
size. Also, the debug routine ohci_dump() has an unused argument.
This patch adds the correct initialization and removes the unused
argument.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Apparently nobody ever remembered to add Scatter-Gather support to
ohci-hcd. This patch adds it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a host controller dies, we don't need to wait for a driver to
time out. We can shut down its URBs immediately. Without this
change, we can end up waiting 30 seconds for a mass-storage transfer
to time out.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some minor fixes and clean-ups to the ftdi_sio, mos7840 and kl5kusb105
drivers for v3.17-rc1.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJTxoJGAAoJEEEN5E/e4bSVhbEP/0EuyDICPe/Xcj/mCaBwzkSX
EIupMPwDdDu+w7/hM8afc22Ijc1nBK09AOHWbfAgQ9Yxj8HRVCazaylsjNoSW3Wu
6QDplfKZBD2X3Y0yg/h6Nk0zFiTOyTkMd7FSWDiOrdjeG4RIU6AgWgncwVYCpPto
0Bb2aHyBUAglXlV2MwnW/tHMvDWC6vPcl+lWQQ2J+zSJcP110LAfu0dqAnh+UuEr
5B6NYORdpz1inXZewIo5vnxJsQxxKMq5T3dUEZkhBaDGYstKReWAHZAb8lhWvLdr
XMA+jhjVmVIVBFeUZYNYJ1xbAGeOqPquhz860jKQizF/fl3uFbPVDFYyrZEHxNoY
KZNXBfuXkv/Dutdk/FaFMq7w8o9q/xWfeupZFLpSSThw3AwR42BvYHyTx8zBLUlf
X2CmtokSDmp233QBAs40S1ZUO1cU7nL7/0C1GF+FR8s3rOjASR2oNGU6KRU7CKCP
AKfKpn3Fo30hvxOICZUuitWbiIYgKQzEHXrKMR8G2awf/AoQgXaoQ1N48lL+57ya
u8vkQLvbcZ2t75qzqEnwPza5BoRGugDD53cTrge06FgsGc0BoujZAP+/PzyvirZV
yuZfbbP5EE8KywryQz7ol9ppGWrmT/TPPU51Eqye2tvePe+O6wAAZ1yU2Nvrg1dS
qwc4S3BKDtoDNqAAx6Yu
=tUqf
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v3.17-rc1
Here are some minor fixes and clean-ups to the ftdi_sio, mos7840 and kl5kusb105
drivers for v3.17-rc1.
Signed-off-by: Johan Hovold <johan@kernel.org>
(introduced in 3.15) that can end up triggering a file system
corruption error after a journal replay. (It shouldn't lead to any
actual data corruption, but it is scary and can force file systems to
be remounted read-only, etc.)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=OX7Z
-----END PGP SIGNATURE-----
Merge tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 bugfixes from Ted Ts'o:
"More bug fixes for ext4 -- most importantly, a fix for a bug
introduced in 3.15 that can end up triggering a file system corruption
error after a journal replay.
It shouldn't lead to any actual data corruption, but it is scary and
can force file systems to be remounted read-only, etc"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix potential null pointer dereference in ext4_free_inode
ext4: fix a potential deadlock in __ext4_es_shrink()
ext4: revert commit which was causing fs corruption after journal replays
ext4: disable synchronous transaction batching if max_batch_time==0
ext4: clarify ext4_error message in ext4_mb_generate_buddy_error()
ext4: clarify error count warning messages
ext4: fix unjournalled bg descriptor while initializing inode bitmap
Samsung, ST & TI. Most of them are of the "this hardware won't work
without this fix" variety, including patches that fix platforms that did
not boot under certain configurations. Other fixes are the result of
changes to the clock core introduced in 3.15 that had subtle impacts on
the clock drivers.
There are no fixes to the clock framework core in this pull request.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=6n8W
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux
Pull clock driver fixes from Mike Turquette:
"This batch of fixes is for a handful of clock drivers from Allwinner,
Samsung, ST & TI. Most of them are of the "this hardware won't work
without this fix" variety, including patches that fix platforms that
did not boot under certain configurations. Other fixes are the result
of changes to the clock core introduced in 3.15 that had subtle
impacts on the clock drivers.
There are no fixes to the clock framework core in this pull request"
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux:
clk: spear3xx: Set proper clock parent of uart1/2
clk: spear3xx: Use proper control register offset
clk: qcom: HDMI source sel is 3 not 2
clk: sunxi: fix devm_ioremap_resource error detection code
clk: s2mps11: Fix double free corruption during driver unbind
clk: ti: am43x: Fix boot with CONFIG_SOC_AM33XX disabled
clk: exynos5420: Remove aclk66_peric from the clock tree description
clk/exynos5250: fix bit number for tv sysmmu clock
clk: s3c64xx: Hookup SPI clocks correctly
clk: samsung: exynos4: Remove SRC_MASK_ISP gates
clk: samsung: add more aliases for s3c24xx
clk: samsung: fix several typos to fix boot on s3c2410
clk: ti: set CLK_SET_RATE_NO_REPARENT for ti,mux-clock
clk: ti: am43x: Fix boot with CONFIG_SOC_AM33XX disabled
clk: ti: dra7: return error code in failure case
clk: ti: apll: not allocating enough data
This week's arm-soc fixes:
- Another set of OMAP fixes
* Clock fixes
* Restart handling
* PHY regulators
* SATA hwmod data for DRA7
+ Some trivial fixes and removal of a bit of dead code
- Exynos fixes
* A bunch of clock fixes
* Some SMP fixes
* Exynos multi-core timer: register as clocksource and fix ftrace.
+ a few other minor fixes
There's also a couple more patches, and at91 fix for USB caused by common
clock conversion, and more MAINTAINERS entries for shmobile.
We're definitely switching to only regression fixes from here on out,
we've been a little less strict than usual up until now.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=NB6g
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"This week's arm-soc fixes:
- Another set of OMAP fixes
* Clock fixes
* Restart handling
* PHY regulators
* SATA hwmod data for DRA7
+ Some trivial fixes and removal of a bit of dead code
- Exynos fixes
* A bunch of clock fixes
* Some SMP fixes
* Exynos multi-core timer: register as clocksource and fix ftrace.
+ a few other minor fixes
There's also a couple more patches, and at91 fix for USB caused by
common clock conversion, and more MAINTAINERS entries for shmobile.
We're definitely switching to only regression fixes from here on out,
we've been a little less strict than usual up until now"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits)
ARM: at91: at91sam9x5: add clocks for usb device
ARM: EXYNOS: Register cpuidle device only on exynos4210 and 5250
ARM: dts: Add clock property for mfc_pd in exynos5420
clk: exynos5420: Add IDs for clocks used in PD mfc
ARM: EXYNOS: Add support for clock handling in power domain
ARM: OMAP2+: Remove non working OMAP HDMI audio initialization
ARM: imx: fix shared gate clock
ARM: dts: Update the parent for Audss clocks in Exynos5420
ARM: EXYNOS: Update secondary boot addr for secure mode
ARM: dts: Fix TI CPSW Phy mode selection on IGEP COM AQUILA.
ARM: dts: am335x-evmsk: Enable the McASP FIFO for audio
ARM: dts: am335x-evm: Enable the McASP FIFO for audio
ARM: OMAP2+: Make GPMC skip disabled devices
ARM: OMAP2+: create dsp device only on OMAP3 SoCs
ARM: dts: dra7-evm: Make VDDA_1V8_PHY supply always on
ARM: DRA7/AM43XX: fix header definition for omap44xx_restart
ARM: OMAP2+: clock/dpll: fix _dpll_test_fint arithmetics overflow
ARM: DRA7: hwmod: Add SYSCONFIG for usb_otg_ss
ARM: DRA7: hwmod: Fixup SATA hwmod
ARM: OMAP3: PRM/CM: Add back macros used by TI DSP/Bridge driver
...
Pull ARM fixes from Russell King:
"Another round of fixes for ARM:
- a set of kprobes fixes from Jon Medhurst
- fix the revision checking for the L2 cache which wasn't noticed to
have been broken"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: l2c: fix revision checking
ARM: kprobes: Fix test code compilation errors for ARMv4 targets
ARM: kprobes: Disallow instructions with PC and register specified shift
ARM: kprobes: Prevent known test failures stopping other tests running
Pull m68k fixes from Geert Uytterhoeven:
"Summary:
- Fix for a boot regression introduced in v3.16-rc1,
- Fix for a build issue in -next"
Christoph Hellwig questioned why mach_random_get_entropy should be
exported to modules, and Geert explains that random_get_entropy() is
called by at least the crypto layer and ends up using it on m68k. On
most other architectures it just uses get_cycles() (which is typically
inlined and doesn't need exporting),
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Export mach_random_get_entropy to modules
m68k: Fix boot regression on machines with RAM at non-zero
Pull parisc fixes from Helge Deller:
"The major patch in here is one which fixes the fanotify_mark() syscall
in the compat layer of the 64bit parisc kernel. It went unnoticed so
long, because the calling syntax when using a 64bit parameter in a
32bit syscall is quite complex and even worse, it may be even
different if you call syscall() or the glibc wrapper. This patch
makes the kernel accept the calling convention when called by the
glibc wrapper.
The other two patches are trivial and remove unused headers, #includes
and adds the serial ports of the fastest C8000 workstation to the
parisc-kernel internal hardware database"
* 'parisc-3.16-5' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: drop unused defines and header includes
parisc: fix fanotify_mark() syscall on 32bit compat kernel
parisc: add serial ports of C8000/1GHz machine to hardware database
The uarts only work when the parent is ras_ahb_clk. The stale 3.5
based ST tree does this in the board file.
Add it to the clk init function. Not pretty, but the mess there is
amazing anyway.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The control register is at offset 0x10, not 0x0. This is wreckaged
since commit 5df33a62c (SPEAr: Switch to common clock framework).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
On parisc we can not use the existing compat implementation for fanotify_mark()
because for the 64bit mask parameter the higher and lower 32bits are ordered
differently than what the compat function expects from big endian
architectures.
Specifically:
It finally turned out, that on hppa we end up with different assignments
of parameters to kernel arguments depending on if we call the glibc
wrapper function
int fanotify_mark (int __fanotify_fd, unsigned int __flags,
uint64_t __mask, int __dfd, const char *__pathname);
or directly calling the syscall manually
syscall(__NR_fanotify_mark, ...)
Reason is, that the syscall() function is implemented as C-function and
because we now have the sysno as first parameter in front of the other
parameters the compiler will unexpectedly add an empty paramenter in
front of the u64 value to ensure the correct calling alignment for 64bit
values.
This means, on hppa you can't simply use syscall() to call the kernel
fanotify_mark() function directly, but you have to use the glibc
function instead.
This patch fixes the kernel in the hppa-arch specifc coding to adjust
the parameters in a way as if userspace calls the glibc wrapper function
fanotify_mark().
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # 3.13+
Pull slave-dmaengine fixes from Vinod Koul:
"We have two small fixes. First one from Daniel to handle 0-length
packets for usb cppi dma. Second by Russell for imx-sdam cyclic
residue reporting"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
Update imx-sdma cyclic handling to report residue
dma: cppi41: handle 0-length packets
- update the parent for Auudss clock because kernel will be hang
during late boot if the parent clock is disabled in bootloader.
- enable clk handing in power domain because while power domain
on/off, its regarding clock source will be reset and it causes
a problem so need to handle it.
- add mux clocks to be used by power domain for exynos5420-mfc
during power domain on/off and property in device tree also.
- register cpuidle only for exynos4210 and exynos5250 because a
system failure will be happened on other exynos SoCs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=didu
-----END PGP SIGNATURE-----
Merge tag 'samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Merge "Samsung fixes-3 for 3.16" from Kukjin Kim:
Samsung fixes-3 for v3.16
- update the parent for Auudss clock because kernel will be hang
during late boot if the parent clock is disabled in bootloader.
- enable clk handing in power domain because while power domain
on/off, its regarding clock source will be reset and it causes
a problem so need to handle it.
- add mux clocks to be used by power domain for exynos5420-mfc
during power domain on/off and property in device tree also.
- register cpuidle only for exynos4210 and exynos5250 because a
system failure will be happened on other exynos SoCs.
* tag 'samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Register cpuidle device only on exynos4210 and 5250
ARM: dts: Add clock property for mfc_pd in exynos5420
clk: exynos5420: Add IDs for clocks used in PD mfc
ARM: EXYNOS: Add support for clock handling in power domain
ARM: dts: Update the parent for Audss clocks in Exynos5420
Signed-off-by: Olof Johansson <olof@lixom.net>
Here are some small USB fixes, PHY driver fixes (they ended up in this
tree for lack of somewhere else to put them), and some new USB device
ids.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlPBnZAACgkQMUfUDdst+ynTkACgwma2Ccj7DJl3g1zFEtM0h8ki
8RYAnirwiO0p1B7gIKlDIgGs25JIwN61
=tNZ2
-----END PGP SIGNATURE-----
Merge tag 'usb-3.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes, PHY driver fixes (they ended up in this
tree for lack of somewhere else to put them), and some new USB device
ids"
* tag 'usb-3.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
phy: omap-usb2: Balance pm_runtime_enable() on probe failure and remove
phy: core: Fix error path in phy_create()
drivers: phy: phy-samsung-usb2.c: Add missing MODULE_DEVICE_TABLE
phy: omap-usb2: fix devm_ioremap_resource error detection code
phy: sun4i: depend on RESET_CONTROLLER
USB: serial: ftdi_sio: Add Infineon Triboard
USB: ftdi_sio: Add extra PID.
usb: option: Add ID for Telewell TW-LTE 4G v2
USB: cp210x: add support for Corsair usb dongle
Here are some small serial fixes that resolve some reported problems
that started in 3.15 with some serial drivers. And there's a new dt
binding for a serial driver, which was all that was needed for the
renesas serial driver.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlPBnRgACgkQMUfUDdst+ymzPACfS2oiP9jIm2ZDEHMSL/MM14Ou
kzQAoNH6BoFub9aOX1OhfsFLri1aEu3x
=pK5r
-----END PGP SIGNATURE-----
Merge tag 'tty-3.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some small serial fixes that resolve some reported problems
that started in 3.15 with some serial drivers.
And there's a new dt binding for a serial driver, which was all that
was needed for the renesas serial driver"
* tag 'tty-3.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: sh-sci: Add device tree support for r8a7{778,740,3a4} and sh73a0
serial: imx: Fix build breakage
serial: arc_uart: Use uart_circ_empty() for open-coded comparison
serial: Test for no tx data on tx restart
Here are 2 hyperv driver fixes, and one i8k driver fix for 3.16.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlPBnhEACgkQMUfUDdst+ym1YgCeKnkaFN0dxOzQ8rNEukts/drQ
twgAni68L9zTp5/g+DWulfom493C6Q8N
=EkjQ
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are two hyperv driver fixes, and one i8k driver fix for 3.16"
* tag 'char-misc-3.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
i8k: Fix non-SMP operation
Drivers: hv: util: Fix a bug in the KVP code
Drivers: hv: vmbus: Fix a bug in the channel callback dispatch code
Here are some IIO driver fixes for 3.16-rc5. Nothing major, just
resolves some minor issues that have been reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlPBnnIACgkQMUfUDdst+yngdgCeKLaRE6md/gey0uV7SeTxuvhk
hG4AoIbphF/tdnRi085qgYEG0IG5nmrz
=VQ9l
-----END PGP SIGNATURE-----
Merge tag 'staging-3.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull IIO fixes from Greg KH:
"Here are some IIO driver fixes for 3.16-rc5. Nothing major, just
resolves some minor issues that have been reported"
* tag 'staging-3.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
iio: ti_am335x_adc: Fix: Use same step id at FIFOs both ends
iio:tcs3472: Check for buffer enabled and locking
iio: hid-sensor-prox: Fix return values
iio: hid-sensor-gyro-3d: Fix return values
iio: hid-sensor-als: Fix return values
iio: hid-sensor-magn-3d: Fix return values
iio: hid-sensor-accel-3d: Fix return values
iio: hid-sensor-press: Fix return values
Dell kernel driver dell-smo8800 provides same freefall interface as hp_accel so
program hpfall.c works also on Dell laptops. So rename it to freefall.c.
Dell driver does not provide hp::hddprotect led so make sure that freefall.c
works also if hp::hddprotect does not exist in sysfs.
Additionally write info to syslog.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Cc: Sonal Santan <sonal.santan@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixed spelling typo in various template files
within Documentation/Docbook.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixed spelling typo found in DocBook/mtdnand.tmpl.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Object-like macros are different than function-like macros:
https://gcc.gnu.org/onlinedocs/cpp/Object-like-Macros.htmlhttps://gcc.gnu.org/onlinedocs/cpp/Function-like-Macros.html
They are not parsed correctly, generating invalid intermediate
files (xmls) for cases like:
#define BIT_MASK (0xFF << BIT_SHIFT)
where "OxFF <<" is considered to be parameter type.
When parsing, we can differentiate beween these two types of macros by
checking whether there is at least one whitespace b/w "#define" and
first opening parenthesis.
Signed-off-by: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The paragraph on mcelog currently describes kernel v2.6.31. In that
kernel the mce code (for i386, that is) was in transition. Ever since
v2.6.32 the situation is much simpler (eg, mcelog is now needed to
process events on almost all x86 machines, i386 and x86-64). Since this
"document is designed to provide a list of the minimum levels of
software necessary to run the 3.0 kernels" let's just describe that
situation.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add clocks for usb device, or else switch to CCF, the gadget
won't work.
Reported-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Tested-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
If probe fails then we need to call pm_runtime_disable() to balance
out the previous pm_runtime_enable() call. Else it will cause
unbalanced pm_runtime_enable() call in the succeding probe call.
This anomaly was observed when the call to devm_phy_create() failed
with -EPROBE_DEFER.
Balance out the pm_runtime_enable() call in .remove() as well.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prevent resources from being freed twice in case device_add() call
fails within phy_create(). Also use ida_simple_remove() instead of
ida_remove() as we had used ida_simple_get() to allocate the ida.
Cc: 3.13+ <stable@vger.kernel.org> # 3.13+
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allow phy-exynos-usb2 to be autoloaded based on devicetree information.
Tested on Odroid X2 with its USB subsystem build as modules.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devm_ioremap_resource returns an ERR_PTR value, not NULL, on failure.
A simplified version of the semantic match that finds this problem is as
follows:
// <smpl>
@@
expression e,e1;
statement S;
@@
*e = devm_ioremap_resource(...);
if (!e1) S
// </smpl>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver depend on the reset framework in a mandatory way. Make sure
reset_control_get is defined by adding this dependency in Kconfig
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb device will autoresume from choose_wakeup() if it is
autosuspended with the wrong wakeup setting, but below errors occur
because usb3503 misc driver will switch to standby mode when suspended.
As add USB_QUIRK_RESET_RESUME, it can stop setting wrong wakeup from
autosuspend_check().
[ 7.734717] usb 1-3: reset high-speed USB device number 3 using exynos-ehci
[ 7.854658] usb 1-3: device descriptor read/64, error -71
[ 8.079657] usb 1-3: device descriptor read/64, error -71
[ 8.294664] usb 1-3: reset high-speed USB device number 3 using exynos-ehci
[ 8.414658] usb 1-3: device descriptor read/64, error -71
[ 8.639657] usb 1-3: device descriptor read/64, error -71
[ 8.854667] usb 1-3: reset high-speed USB device number 3 using exynos-ehci
[ 9.264598] usb 1-3: device not accepting address 3, error -71
[ 9.374655] usb 1-3: reset high-speed USB device number 3 using exynos-ehci
[ 9.784601] usb 1-3: device not accepting address 3, error -71
[ 9.784838] usb usb1-port3: device 1-3 not suspended yet
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb3503 needs to switch to standby mode while suspending and should
switch to hub mode when resumed. Also we can control clock on PM
function.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simply document new compat strings.
There appears to be no need for a driver updates.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix breakage introduced by
commit c557d392fb,
'serial: Test for no tx data on tx restart'.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull x86 fixes from Peter Anvin:
"A couple of further build fixes for the VDSO code.
This is turning into a bit of a headache, and Andy has already come up
with a more ultimate cleanup, but most likely that is 3.17 material"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86-32, vdso: Fix vDSO build error due to missing align_vdso_addr()
x86-64, vdso: Fix vDSO build breakage due to empty .rela.dyn
Pull nfsd bugfix from Bruce Fields:
"Another xdr encoding regression that may cause incorrect encoding on
failures of certain readdirs"
* 'for-3.16' of git://linux-nfs.org/~bfields/linux:
nfsd: Fix bad reserving space for encoding rdattr_error
Commit 007649375f ("ext4: initialize multi-block allocator before
checking block descriptors") causes the block group descriptor's count
of the number of free blocks to become inconsistent with the number of
free blocks in the allocation bitmap. This is a harmless form of fs
corruption, but it causes the kernel to potentially remount the file
system read-only, or to panic, depending on the file systems's error
behavior.
Thanks to Eric Whitney for his tireless work to reproduce and to find
the guilty commit.
Fixes: 007649375f ("ext4: initialize multi-block allocator before checking block descriptors"
Cc: stable@vger.kernel.org # 3.15
Reported-by: David Jander <david@protonic.nl>
Reported-by: Matteo Croce <technoboy85@gmail.com>
Tested-by: Eric Whitney <enwlinux@gmail.com>
Suggested-by: Eric Whitney <enwlinux@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
multipath_busy. This impacted cable-pull testing and also the ability
to boot with IPR SCSI on a POWER8 box.
. Fix possible deadlock with deferred device removal by using a new
dedicated workqueue rather than using the system workqueue.
. Fix NULL pointer crash due to race condition in dm-io's wake up code
for sync_io by using a completion.
. Update dm-crypt and dm-zero author name following legal name change;
this is important to Jana so I didn't see any reason to hold it back.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTv+hvAAoJEMUj8QotnQNawwMH/2yQ7AE3dh44jGr1fp0UEP8e
Vd7HWtUJAm4+lYkPH7AjLCw3YBwWh/ajLXAwMpPBI878o5sgoWTfnq0hbecqoWkt
5EugETiZ20C3K/llNFpw9xdtlObFwI21WUGqmu8ygYvfSvdbg6THPT5o8BdtEvnb
MDBrrrpBpUwMCGw3v7jIoYrKZbWmp46iy5KwVqBbXnD3shpOU8KpasyIOrqlrqjJ
z7BzfprN6ut1zaVs83N4iPMPnSPrIloUisGpPn1r74qRYUv/AXQgiv09WPA3keTN
erRGFU9Mr0I4MGOLTuqHyCVO0t4tze1pL8jwEk29GUkXXcr9Is4p9I307Cm7WvE=
=pBlO
-----END PGP SIGNATURE-----
Merge tag 'dm-3.16-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- Fix DM multipath IO hang regression from 3.15 due to logic bug in
multipath_busy. This impacted cable-pull testing and also the
ability to boot with IPR SCSI on a POWER8 box.
- Fix possible deadlock with deferred device removal by using a new
dedicated workqueue rather than using the system workqueue.
- Fix NULL pointer crash due to race condition in dm-io's wake up code
for sync_io by using a completion.
- Update dm-crypt and dm-zero author name following legal name change;
this is important to Jana so I didn't see any reason to hold it back.
* tag 'dm-3.16-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm mpath: fix IO hang due to logic bug in multipath_busy
dm io: fix a race condition in the wake up code for sync_io
dm crypt, dm zero: update author name following legal name change
dm: allocate a special workqueue for deferred device removal
