Lighter weight than using the 3D engine.
v2: fix ring count
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This adds dpm support for rv7xx asics. This includes:
- clockgating
- dynamic engine clock scaling
- dynamic memory clock scaling
- dynamic voltage scaling
- dynamic pcie gen1/gen2 switching
Set radeon.dpm=1 to enable.
v2: reduce stack usage
v3: fix 64 bit div
v4: fix state enable
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This adds dpm support for rv6xx asics. This includes:
- clockgating
- dynamic engine clock scaling
- dynamic memory clock scaling
- dynamic voltage scaling
- dynamic pcie gen1/gen2 switching
Set radeon.dpm=1 to enable.
v2: remove duplicate line
v3: fix thermal interrupt check noticed by Jerome
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
This is required for certain advanced functionality.
v2: save/restore list takes dword offsets
v3: rebase on gpu reset changes
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Instead of duplicating the code over and over again, just use a single
function to handle the clock calculations.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Just everything needed to decode videos using UVD.
v6: just all the bugfixes and support for R7xx-SI merged in one patch
v7: UVD_CGC_GATE is a write only register, lockup detection fix
v8: split out VRAM fallback changes, remove support for RV770,
add support for HEMLOCK, add buffer sizes checks
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When we attempt the reset the GPU, look at the status registers
to determine what blocks need to be reset.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
After refactoring the _cs logic, we ended up with many
macros and constants that #define the same thing.
Clean'em up.
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Reviewed-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Checking of the second colorbuffer was skipped on r700, because
CB_TARGET_MASK was 0xf. With r600, CB_TARGET_MASK is changed to 0xff,
so we must set the number of samples of the second colorbuffer to 1 in order
to pass the CS checker.
The DRM version is bumped, because RESOLVE_BOX is always rejected without this
fix on r600.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
MSAA is impossible without them.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Returns a snapshot of the GPU clock counter. Needed
for certain OpenGL extensions.
v2: agd5f
- address Jerome's comments
- add function documentation
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Print various CP register that have valuable informations regarding
GPU lockup.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Required for streamout. Bump drm minor.
Marek v2: fix pkt->count check
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- SMX_SAR_CTL0 needs to be programmed correctly to prevent
problems with memory exports in certain cases.
- VC_ENHANCE needs to be initialized on 6xx/7xx.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Tiling group size is always 256bits on r6xx/r7xx/r8xx/9xx. Also fix and
simplify render backend map. This now properly sets up the backend map
on r6xx-9xx which should improve 3D performance.
Vadim benchmarked also:
Some benchmarks on juniper (5750), fullscreen 1920x1080,
first result - kernel 3.4.0+ (fb21affa), second - with these patches:
Lightsmark: 91 fps => 123 fps +35%
Doom3: 74 fps => 101 fps +36%
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Introduce special struct radeon_afmt for this purpose.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Tested-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Christian König <deathsimple@vodafone.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds register definitions for HDMI/DP audio on
DCE2/3/4/5 hardware.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
For 6xx+. Required for mesa to use htile support for HiZ/HiS.
Userspace will check radeon version 2.14 with is bumped either
by tiling patch or stream out patch. This patch only add support
for htile relocation which should be enough for any userspace
to implement the hyperz (using htile buffer) feature.
v2: Jerome: Fix size checking for htile buffer.
v3: Jerome: Adapt on top of r600/evergreen cs checker changes,
also check htile surface in case only stencil is
present.
Signed-off-by: Pierre-Eric Pelloux-Prayer <pelloux@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The out of order execution of semaphore commands on
pre cayman asics doesn't work correctly and can
cause deadlocks, so turn it off for now.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
evergreen and northern island gpu needs more informations for 2D tiling
than previous r6xx/r7xx. Add field to tiling ioctl to allow userspace
to provide those.
The v8 cs checking change to track color view on r6xx/r7xx doesn't
affect old userspace as old userspace always emited 0 for this register.
v2 fix r6xx/r7xx 2D tiling computation
v3 fix r6xx/r7xx height align for untiled surface & add support for
tile split on evergreen and newer
v4 improve tiling debugging output
v5 fix tile split code for evergreen and newer
v6 set proper tile split for crtc register
v7 fix tile split limit value
v8 add COLOR_VIEW checking to r6xx/r7xx checker, add evergreen cs
checking, update safe reg for r600, evergreen and cayman.
Evergreen checking need some work around for stencil alignment
issues
v9 fix tile split value range, fix compressed texture handling and
mipmap calculation, allow evergreen check to be silencious in
front of current broken userspace (depth/stencil alignment issue)
v10 fix eg 3d texture and compressed texture, fix r600 depth array,
fix r600 color view computation, add support for evergreen stencil
split
v11 more verbose debugging in some case
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
v2: agd5f: add strmout CS checking, copy_dw register checking
v3: agd5f: don't use cs_check_reg() for copy_dw checking as it
will incorrectly patch the command stream for certain regs.
v4: agd5f: add warning if safe reg check fails for copy_dw
v5: agd5f: add stricter checking for 6xx/7xx
v6: agd5f: add range checking for copy_dw on eg+,
add sx_surface_sync to safe reg list for 7xx.
v7: agd5f: add stricter checking for eg+
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
They are used to sync between rings, while fences
sync between a ring and the cpu.
v2 Fix radeon_semaphore_driver_fini when no semaphore were
allocated.
v3 Initialize list early on to avoid issue in case or early
error
Signed-off-by: Christian König <deathsimple@vodafone.de>
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
some 3d register bits look like magic in r600 blit functions
use predefined constants to make it more intuitive what they are
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
BC6 and BC7 are described in ARB_texture_compression_bptc.
No idea what FMT_32_AS_32_32_32_32 is good for.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'intel/drm-intel-next' of ../drm-next: (755 commits)
drm/i915: Only wait on a pending flip if we intend to write to the buffer
drm/i915/dp: Sanity check eDP existence
drm/i915: Rebind the buffer if its alignment constraints changes with tiling
drm/i915: Disable GPU semaphores by default
drm/i915: Do not overflow the MMADDR write FIFO
Revert "drm/i915: fix corruptions on i8xx due to relaxed fencing"
drm/i915: Don't save/restore hardware status page address register
drm/i915: don't store the reg value for HWS_PGA
drm/i915: fix memory corruption with GM965 and >4GB RAM
Linux 2.6.38-rc7
Revert "TPM: Long default timeout fix"
drm/i915: Re-enable GPU semaphores for SandyBridge mobile
drm/i915: Replace vblank PM QoS with "Interrupt-Based AGPBUSY#"
Revert "drm/i915: Use PM QoS to prevent C-State starvation of gen3 GPU"
drm/i915: Allow relocation deltas outside of target bo
drm/i915: Silence an innocuous compiler warning for an unused variable
fs/block_dev.c: fix new kernel-doc warning
ACPI: Fix build for CONFIG_NET unset
mm: <asm-generic/pgtable.h> must include <linux/mm_types.h>
x86: Use u32 instead of long to set reset vector back to 0
...
Conflicts:
drivers/gpu/drm/i915/i915_gem.c
the texture checking code didn't work for block formats like s3tc,
this overhauls it to work for all types.
v2: add texture array support.
v3: add subsampled formats
Signed-off-by: Dave Airlie <airlied@redhat.com>
agd5f: minor cleanups
Signed-off-by: Cédric Cano <ccano@interfaceconcept.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Supported on rv6xx/r7xx/evergreen. Cards come up in gen1 mode.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds support for dri2 pageflipping.
v2: precision updates from Mario Kleiner.
v3: Multihead fixes from Mario Kleiner; missing crtc offset
add note about update pending bit on pre-avivo chips
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Tiled buffers have the same alignment requirements regardless of
whether the surface is for db, cb, or textures. Previously, the
calculations where inconsistent for each buffer type.
- Unify the alignment calculations in a common function
- Standardize the alignment units (pixels for pitch/height/depth,
bytes for base)
- properly check the buffer base alignments
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On r6xx+ a newer fence mechanism was implemented to replace
the old wait_until plus scratch regs setup. A single EOP event
will flush the destination caches, write a fence value, and generate
an interrupt. This is the recommended fence mechanism on r6xx+ asics.
This requires my previous writeback patch.
v2: fix typo that enabled event fence checking on all asics
rather than just r6xx+.
v3: properly enable EOP interrupts
Should fix:
https://bugs.freedesktop.org/show_bug.cgi?id=29972
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Use of HDP_*_COHERENCY_FLUSH_CNTL can cause a hang in certain
situations. Add workaround.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Check for relocs for DB_DEPTH_INFO, CB_COLOR*_INFO, and texture
resources.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
rv6xx/rv7xx/evergreen families supported; older asics did
not have an internal thermal sensor.
Note, not all oems use the internal thermal sensor, so it's
only exposed in cases where it is used.
Note also, that most laptops use an oem specific ACPI solution for
GPU thermal information rather than using the internal thermal
sensor directly.
v2: export millidegrees celsius, use hwmon device properly.
v3: fix Kconfig
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- Drop some more safe regs taht userspace shouldn't hit
- Constant base regs need relocs. This allows us to use
constant buffers rather than the constant register file.
Also we don't want userspace to be able to set arbitrary
mc base values for the const caches.
- Track SQ_CONFIG so we know whether userspace is using
the cfile or constant buffers.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch add cs checker to r600/r700 hw. Command stream checking
will rewrite some of the cs value in order to restrict GPU access
to BO size. This doesn't break old userspace but just enforce safe
value. It should break any things that was using the r600/r700 cs
ioctl to do forbidden things (malicious software), though we are
not aware of such things.
Here is the list of thing we check :
- enforcing resource size
- enforcing color buffer slice tile max, will restrict cb access
- enforcing db buffer slice tile max, will restrict db access
We don't check for shader bigger than the BO in which they are
supposed to be, such use would lead to GPU lockup and is harmless
from security POV, as far as we can tell (note that even checking
for this wouldn't prevent someone to write bogus shader that lead
to lockup).
This patch has received as much testing as humanly possible with
old userspace to check that it didn't break such configuration.
However not all the applications out there were tested, thus it
might broke some odd, rare applications.
[airlied: fix rules for cs checker for parallel builds]
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch workaround a possible security issue which can allow
user to abuse drm on r6xx/r7xx hw to access any system ram memory.
This patch doesn't break userspace, it detect "valid" old use of
CB_COLOR[0-7]_FRAG & CB_COLOR[0-7]_TILE registers and overwritte
the address these registers are pointing to with the one of the
last color buffer. This workaround will work for old mesa &
xf86-video-ati and any old user which did use similar register
programming pattern as those (we expect that there is no others
user of those ioctl except possibly a malicious one). This patch
add a warning if it detects such usage, warning encourage people
to update their mesa & xf86-video-ati. New userspace will submit
proper relocation.
Fix for xf86-video-ati / mesa (this kernel patch is enough to
prevent abuse, fix for userspace are to set proper cs stream and
avoid kernel warning) :
http://cgit.freedesktop.org/xorg/driver/xf86-video-ati/commit/?id=95d63e408cc88b6934bec84a0b1ef94dfe8bee7bhttp://cgit.freedesktop.org/mesa/mesa/commit/?id=46dc6fd3ed5ef96cda53641a97bc68c3bc104a9f
Abusing this register to perform system ram memory is not easy,
here is outline on how it could be achieve. First attacker must
have access to the drm device and be able to submit command stream
throught cs ioctl. Then attacker must build a proper command stream
for r6xx/r7xx hw which will abuse the FRAG or TILE buffer to
overwrite the GPU GART which is in VRAM. To achieve so attacker
as to setup CB_COLOR[0-7]_FRAG or CB_COLOR[0-7]_TILE to point
to the GPU GART, then it has to find a way to write predictable
value into those buffer (with little cleverness i believe this
can be done but this is an hard task). Once attacker have such
program it can overwritte GPU GART to program GPU gart to point
anywhere in system memory. It then can reusse same method as he
used to reprogram GART to overwritte the system ram through the
GART mapping. In the process the attacker has to be carefull to
not overwritte any sensitive area of the GART table, like ring
or IB gart entry as it will more then likely lead to GPU lockup.
Bottom line is that i think it's very hard to use this flaw
to get system ram access but in theory one can achieve so.
Side note: I am not aware of anyone ever using the GPU as an
attack vector, nevertheless we take great care in the opensource
driver to try to detect and forbid malicious use of GPU. I don't
think the closed source driver are as cautious as we are.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This enables the use of interrupts on r6xx/r7xx hardware.
Interrupts are implemented via a ring buffer. The GPU adds
interrupts vectors to the ring and the host reads them off
in the interrupt handler. The interrupt controller requires
firmware like the CP. This firmware must be installed and
accessble to the firmware loader for interrupts to function.
MSIs don't seem to work on my RS780. They work fine on all
my discrete cards. I'm not sure about other RS780s or
RS880s. I've disabled MSIs on RS780 and RS880, but it would
probably be worth checking on some other systems.
v2 - fix some checkpatch.pl problems;
re-read the disp int status reg if we restart the ih;
v3 - remove the irq handler if r600_irq_init() fails;
remove spinlock in r600_ih_ring_fini();
move ih rb overflow check to r600_get_ih_wptr();
move irq ack to separate function;
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
rendercheck under kms on r600s was failing due to HDP flushing not happening.
This adds HDP flushing to the object wait function for r100->r700 families.
rendercheck passes basic tests on r600 with this change.
Acked-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
