If controller driver has specified the irq_flags, mhi uses this specified
irq_flags. Otherwise, mhi uses default irq_flags.
The purpose of this change is to support one MSI vector for QCA6390.
MHI will use one same MSI vector too in this scenario.
In case of one MSI vector, IRQ_NO_BALANCING is needed when irq handler
is requested. The reason is if irq migration happens, the msi_data may
change too. However, the msi_data is already programmed to QCA6390
hardware during initialization phase. This msi_data inconsistence will
result in crash in kernel.
Another issue is in case of one MSI vector, IRQF_NO_SUSPEND will trigger
WARNINGS because QCA6390 wants to disable the IRQ during the suspend.
To avoid above two issues, QCA6390 driver specifies the irq_flags in case
of one MSI vector when mhi_register_controller is called.
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
When a shared MSI vector must be used (e.g. when VTd is disabled on
x86_64), each event MSI vector must be set to the shared vector idx.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Hemant Kumar<hemantk@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The ring element data, though being part of coherent memory, still need
to be performed before updating the ring context to point to this new
element. That can be guaranteed with a memory barrier (dma_wmb).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
MHI hardware channels are usually the hardware accelerated data path
e.g. IP packets path for modems. This path needs to be optimized for
low latency and high throughput. After several tests on FN980m SDX55
based modem, it seems 1ms is a good default irq_moderation value:
- It allows to reach the maximum download throughput
- It introduces limited latency (5ms is too high)
- It prevents interrupt flooding
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add support for Diag over MHI. Qualcomm Diag is the qualcomm
diagnostics interface that can be used to collect modem logs,
events, traces, etc. It can be used by tools such QPST or QXDM.
This patch adds the DIAG channels and a dedicated event ring.
Reviewed-by Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
On cold boot, device can take slightly more than 5 seconds to start.
Increase the timeout to prevent MHI power-up issues.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
If the modem crashes for any reason, we may not be able to detect
it at MHI level (MHI registers not reachable anymore).
This patch implements a health-check mechanism to check regularly
that device is alive (MHI layer can communicate with). If device
is not alive (because a crash or unexpected reset), the recovery
procedure is triggered.
Tested successfully with Telit FN980m module.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
In AER capable root complex, errors are reported to the host which
can then act accordingly and perform PCI recovering procedure.
This patch enables error reporting and implements error_detected,
slot_reset and resume callbacks.
Reviewed-by Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add support for system wide suspend/resume. During suspend, MHI
device controller must be put in M3 state and PCI bus in D3 state.
Add a recovery procedure allowing to reinitialize the device in case
of error during resume steps, which can happen if device loses power
(and so its context) while system suspend.
Reviewed-by Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add support for resetting the device, reset can be triggered in case
of error or manually via sysfs (/sys/bus/pci/devices/*/reset).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Hardware channels have a feature called burst mode that allows to
queue transfer ring element(s) (TRE) to a channel without ringing
the device doorbell. In that mode, the device is polling the channel
context for new elements. This reduces the frequency of host initiated
doorbells and increase throughput.
Create a new dedicated macro for hardware channels with burst enabled.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
If the IPA (IP hardware accelerator) is starved of event ring elements,
the modem is crashing (SDX55). That can be prevented by setting a
larger number of events (i.e 2 x number of channel ring elements).
Tested with FN980m module.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The MHI specification allows to perform a hard reset of the device
when writing to the SOC_RESET register. It can be used to completely
restart the device (e.g. in case of unrecoverable MHI error).
This is up to the MHI controller driver to determine when this hard
reset should be used, and in case of MHI errors, should be used as
a reset of last resort (after standard MHI stack reset).
This function is a stateless function, the MHI layer do nothing except
triggering the reset by writing into the right register(s), this is up
to the caller to ensure right mhi_controller state (e.g. unregister the
controller if necessary).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
There are a couple of subsystems maintained by other people that
merge their drivers through the SoC tree, those changes include:
- The SCMI firmware framework gains support for sensor notifications
and for controlling voltage domains.
- A large update for the Tegra memory controller driver, integrating
it better with the interconnect framework
- The memory controller subsystem gains support for Mediatek MT8192
- The reset controller framework gains support for sharing pulsed
resets
For Soc specific drivers in drivers/soc, the main changes are
- The Allwinner/sunxi MBUS gets a rework for the way it handles
dma_map_ops and offsets between physical and dma address spaces.
- An errata fix plus some cleanups for Freescale Layerscape SoCs
- A cleanup for renesas drivers regarding MMIO accesses.
- New SoC specific drivers for Mediatek MT8192 and MT8183 power domains
- New SoC specific drivers for Aspeed AST2600 LPC bus control
and SoC identification.
- Core Power Domain support for Qualcomm MSM8916, MSM8939, SDM660
and SDX55.
- A rework of the TI AM33xx 'genpd' power domain support to use
information from DT instead of platform data
- Support for TI AM64x SoCs
- Allow building some Amlogic drivers as modules instead of built-in
Finally, there are numerous cleanups and smaller bug fixes for
Mediatek, Tegra, Samsung, Qualcomm, TI OMAP, Amlogic, Rockchips,
Renesas, and Xilinx SoCs.
There is a trivial conflict in the cedrus driver, with two branches
adding the same CEDRUS_CAPABILITY_H265_DEC flag, and another trivial
remove/remove conflict in linux/dma-mapping.h.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=BjJf
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-drivers-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"There are a couple of subsystems maintained by other people that merge
their drivers through the SoC tree, those changes include:
- The SCMI firmware framework gains support for sensor notifications
and for controlling voltage domains.
- A large update for the Tegra memory controller driver, integrating
it better with the interconnect framework
- The memory controller subsystem gains support for Mediatek MT8192
- The reset controller framework gains support for sharing pulsed
resets
For Soc specific drivers in drivers/soc, the main changes are
- The Allwinner/sunxi MBUS gets a rework for the way it handles
dma_map_ops and offsets between physical and dma address spaces.
- An errata fix plus some cleanups for Freescale Layerscape SoCs
- A cleanup for renesas drivers regarding MMIO accesses.
- New SoC specific drivers for Mediatek MT8192 and MT8183 power
domains
- New SoC specific drivers for Aspeed AST2600 LPC bus control and SoC
identification.
- Core Power Domain support for Qualcomm MSM8916, MSM8939, SDM660 and
SDX55.
- A rework of the TI AM33xx 'genpd' power domain support to use
information from DT instead of platform data
- Support for TI AM64x SoCs
- Allow building some Amlogic drivers as modules instead of built-in
Finally, there are numerous cleanups and smaller bug fixes for
Mediatek, Tegra, Samsung, Qualcomm, TI OMAP, Amlogic, Rockchips,
Renesas, and Xilinx SoCs"
* tag 'arm-soc-drivers-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (222 commits)
soc: mediatek: mmsys: Specify HAS_IOMEM dependency for MTK_MMSYS
firmware: xilinx: Properly align function parameter
firmware: xilinx: Add a blank line after function declaration
firmware: xilinx: Remove additional newline
firmware: xilinx: Fix kernel-doc warnings
firmware: xlnx-zynqmp: fix compilation warning
soc: xilinx: vcu: add missing register NUM_CORE
soc: xilinx: vcu: use vcu-settings syscon registers
dt-bindings: soc: xlnx: extract xlnx, vcu-settings to separate binding
soc: xilinx: vcu: drop useless success message
clk: samsung: mark PM functions as __maybe_unused
soc: samsung: exynos-chipid: initialize later - with arch_initcall
soc: samsung: exynos-chipid: order list of SoCs by name
memory: jz4780_nemc: Fix potential NULL dereference in jz4780_nemc_probe()
memory: ti-emif-sram: only build for ARMv7
memory: tegra30: Support interconnect framework
memory: tegra20: Support hardware versioning and clean up OPP table initialization
dt-bindings: memory: tegra20-emc: Document opp-supported-hw property
soc: rockchip: io-domain: Fix error return code in rockchip_iodomain_probe()
reset-controller: ti: force the write operation when assert or deassert
...
- enabled GCOV
- reworked setup of protection map
- added support for more MSCC platforms
- added sysfs boardinfo for Loongson64
- enabled KASLR for Loogson64
- added reset controller for BCM63xx
- cleanups and fixes
-----BEGIN PGP SIGNATURE-----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=0Sht
-----END PGP SIGNATURE-----
Merge tag 'mips_5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Thomas Bogendoerfer:
- enable GCOV
- rework setup of protection map
- add support for more MSCC platforms
- add sysfs boardinfo for Loongson64
- enable KASLR for Loogson64
- add reset controller for BCM63xx
- cleanups and fixes
* tag 'mips_5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (70 commits)
mips: fix Section mismatch in reference
MAINTAINERS: Add linux-mips mailing list to JZ47xx entries
MAINTAINERS: Remove JZ4780 DMA driver entry
MAINTAINERS: chenhc@lemote.com -> chenhuacai@kernel.org
MIPS: Octeon: irq: Alloc desc before configuring IRQ
MIPS: mm: Add back define for PAGE_SHARED
MIPS: Select ARCH_KEEP_MEMBLOCK if DEBUG_KERNEL to enable sysfs memblock debug
mips: lib: uncached: fix non-standard usage of variable 'sp'
MIPS: DTS: img: Fix schema warnings for pwm-leds
MIPS: KASLR: Avoid endless loop in sync_icache if synci_step is zero
MIPS: Move memblock_dump_all() to the end of setup_arch()
MIPS: SMP-CPS: Add support for irq migration when CPU offline
MIPS: OCTEON: Don't add kernel sections into memblock allocator
MIPS: Don't round up kernel sections size for memblock_add()
MIPS: Enable GCOV
MIPS: configs: drop unused BACKLIGHT_GENERIC option
MIPS: Loongson64: Fix up reserving kernel memory range
MIPS: mm: Remove unused is_aligned_hugepage_range
MIPS: No need to check CPU 0 in {loongson3,bmips,octeon}_cpu_disable()
mips: cdmm: fix use-after-free in mips_cdmm_bus_discover
...
Here is the big char/misc driver update for 5.11-rc1.
Continuing the tradition of previous -rc1 pulls, there seems to be more
and more tiny driver subsystems flowing through this tree.
Lots of different things, all of which have been in linux-next for a
while with no reported issues:
- extcon driver updates
- habannalab driver updates
- mei driver updates
- uio driver updates
- binder fixes and features added
- soundwire driver updates
- mhi bus driver updates
- phy driver updates
- coresight driver updates
- fpga driver updates
- speakup driver updates
- slimbus driver updates
- various small char and misc driver updates
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX9iDZA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylRMACgqxKS2CUcY8tPnR5weHEsbz6O+KAAn3BtEFnK
7V9EnSuZe4L1jNOHOB5V
=xzHh
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc driver updates from Greg KH:
"Here is the big char/misc driver update for 5.11-rc1.
Continuing the tradition of previous -rc1 pulls, there seems to be
more and more tiny driver subsystems flowing through this tree.
Lots of different things, all of which have been in linux-next for a
while with no reported issues:
- extcon driver updates
- habannalab driver updates
- mei driver updates
- uio driver updates
- binder fixes and features added
- soundwire driver updates
- mhi bus driver updates
- phy driver updates
- coresight driver updates
- fpga driver updates
- speakup driver updates
- slimbus driver updates
- various small char and misc driver updates"
* tag 'char-misc-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (305 commits)
extcon: max77693: Fix modalias string
extcon: fsa9480: Support TI TSU6111 variant
extcon: fsa9480: Rewrite bindings in YAML and extend
dt-bindings: extcon: add binding for TUSB320
extcon: Add driver for TI TUSB320
slimbus: qcom: fix potential NULL dereference in qcom_slim_prg_slew()
siox: Make remove callback return void
siox: Use bus_type functions for probe, remove and shutdown
spmi: Add driver shutdown support
spmi: fix some coding style issues at the spmi core
spmi: get rid of a warning when built with W=1
uio: uio_hv_generic: use devm_kzalloc() for private data alloc
uio: uio_fsl_elbc_gpcm: use device-managed allocators
uio: uio_aec: use devm_kzalloc() for uio_info object
uio: uio_cif: use devm_kzalloc() for uio_info object
uio: uio_netx: use devm_kzalloc() for or uio_info object
uio: uio_mf624: use devm_kzalloc() for uio_info object
uio: uio_sercos3: use device-managed functions for simple allocs
uio: uio_dmem_genirq: finalize conversion of probe to devm_ handlers
uio: uio_dmem_genirq: convert simple allocations to device-managed
...
Because the minimum supported DPRC version is 6.0, there is no need to
check for incompatible 6.x versions lower to the minimum one. Just
remove the second half of the check to simplify the logic.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20201123164839.1668409-1-ciorneiioana@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 197f4d6a4a ("staging: fsl-mc: fsl-mc object allocator driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Acked-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1607068967-31991-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'type' and 'flags' fields were missing from dprc_rsp_get_obj_region
structure therefore the MC Bus driver was not receiving proper flags
from MC like DPRC_REGION_CACHEABLE.
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Cristian Sovaiala <cristian.sovaiala@freescale.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Link: https://lore.kernel.org/r/20201124111200.1391-1-laurentiu.tudor@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some bootloaders might pause the MC firmware before starting the
kernel to ensure that MC will not cause faults as soon as SMMU
probes due to no configuration being in place for the firmware.
Make sure that MC is resumed at probe time as its SMMU setup should
be done by now.
Also included, a comment fix on how PL and BMT bits are packed in
the StreamID.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Link: https://lore.kernel.org/r/20201105153050.19662-2-laurentiu.tudor@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A previous patch accidentally dropped an error check, so add it back.
Fixes: aef85b56c3 ("bus: fsl-mc: MC control registers are not always available")
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Link: https://lore.kernel.org/r/20201105153050.19662-1-laurentiu.tudor@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
First set of patches for v5.11. rtw88 getting improvements to work
better with Bluetooth and other driver also getting some new features.
mhi-ath11k-immutable branch was pulled from mhi tree to avoid
conflicts with mhi tree.
Major changes:
rtw88
* major bluetooth co-existance improvements
wilc1000
* Wi-Fi Multimedia (WMM) support
ath11k
* Fast Initial Link Setup (FILS) discovery and unsolicited broadcast
probe response support
* qcom,ath11k-calibration-variant Device Tree setting
* cold boot calibration support
* new DFS region: JP
wnc36xx
* enable connection monitoring and keepalive in firmware
ath10k
* firmware IRAM recovery feature
mhi
* merge mhi-ath11k-immutable branch to make MHI API change go smoothly
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJfyTQyAAoJEG4XJFUm622bCdcIAIyVnqdW7pnoDmWIyQmAEnD9
vGARkzghPHXnufpOzohyDdxT12X9klhrxSVIgzEgH1/pl3i1PpnF6KXyGFCC44Lw
wrLXhQygPzmIW1IZtJJE3G72WExXoRjWx6LD1I7C7oEIduqFixXADmK2tKzFp795
Jxum+sOeT6+Dk1OvO/fIroBHX73mRE9zAuiTIMpt2G1j8uXs9QVfcTbTrUshLASN
0sX9J6JutltBuM4G7+bFpVzKnLnlQ7ebUaF6nvTCQsgHWZwkS7yAubSWX9sFohbR
UXgQHNE83s/esOg7nBxAfqTKP8mbxsobmxZtxE5GR5vFY5FJDxqP9Zc2KzPp39w=
=CbX/
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-12-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.11
First set of patches for v5.11. rtw88 getting improvements to work
better with Bluetooth and other driver also getting some new features.
mhi-ath11k-immutable branch was pulled from mhi tree to avoid
conflicts with mhi tree.
Major changes:
rtw88
* major bluetooth co-existance improvements
wilc1000
* Wi-Fi Multimedia (WMM) support
ath11k
* Fast Initial Link Setup (FILS) discovery and unsolicited broadcast
probe response support
* qcom,ath11k-calibration-variant Device Tree setting
* cold boot calibration support
* new DFS region: JP
wnc36xx
* enable connection monitoring and keepalive in firmware
ath10k
* firmware IRAM recovery feature
mhi
* merge mhi-ath11k-immutable branch to make MHI API change go smoothly
* tag 'wireless-drivers-next-2020-12-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next: (180 commits)
wl1251: remove trailing semicolon in macro definition
airo: remove trailing semicolon in macro definition
wilc1000: added queue support for WMM
wilc1000: call complete() for failure in wilc_wlan_txq_add_cfg_pkt()
wilc1000: free resource in wilc_wlan_txq_add_mgmt_pkt() for failure path
wilc1000: free resource in wilc_wlan_txq_add_net_pkt() for failure path
wilc1000: added 'ndo_set_mac_address' callback support
brcmfmac: expose firmware config files through modinfo
wlcore: Switch to using the new API kobj_to_dev()
rtw88: coex: add feature to enhance HID coexistence performance
rtw88: coex: upgrade coexistence A2DP mechanism
rtw88: coex: add action for coexistence in hardware initial
rtw88: coex: add function to avoid cck lock
rtw88: coex: change the coexistence mechanism for WLAN connected
rtw88: coex: change the coexistence mechanism for HID
rtw88: coex: update AFH information while in free-run mode
rtw88: coex: update the mechanism for A2DP + PAN
rtw88: coex: add debug message
rtw88: coex: run coexistence when WLAN entering/leaving LPS
Revert "rtl8xxxu: Add Buffalo WI-U3-866D to list of supported devices"
...
====================
Link: https://lore.kernel.org/r/20201203185732.9CFA5C433ED@smtp.codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Here is the MHI patch set for v5.11. Most of the patches are cleanups and fixes
but there are some noticeable changes too:
1. Loic finally removed the auto-start option from the channel parameters of the
MHI controller. It is the duty of the client drivers like qrtr to start/stop the
channels when required, so we decided to remove this option. As a side effect,
we changed the qrtr driver to start the channels during its probe and removed
the auto-start option from ath11k controller.
**NOTE** Since these changes spawns both MHI and networking trees, the patches
are maintained in an immutable branch [1] and pulled into both mhi-next and
ath11k-next branches. The networking patches got acks from ath11k and networking
maintainers as well.
2. Loic added a generic MHI pci controller driver. This driver will be used by
the PCI based Qualcomm modems like SDX55 and exposes channels such as QMI,
IP_HW0, IPCR etc...
3. Loic fixed the MHI device hierarchy by maintaining the correct parent child
relationships. Earlier all MHI devices lived in the same level under the parent
device like PCIe. But now, the MHI devices belonging to channels will become the
children of controller MHI device.
4. Finally Loic also improved the MHI device naming by using indexed names such
as mhi0, mhi1, etc... This will break the userspace applications depending on
the old naming convention but since the only one user so far is Jeff Hugo's AI
accelerator apps, we decided to make this change now itself with his agreement.
5. Bhaumik fixed the qrtr driver by stopping the channels during remove. This
patch also got ack from networking maintainer and we decided to take it through
MHI tree (via immutable branch) since we already had a qrtr change.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/mani/mhi.git/log/?h=mhi-ath11k-immutable
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEZ6VDKoFIy9ikWCeXVZ8R5v6RzvUFAl/Hwn4ACgkQVZ8R5v6R
zvWCQQgAh7vbwjAvxmzk5OTkuenv9YRV8lYMNTt1zdnXt8k0navv2Tc2M4e6VKbS
WFGCSUCBUQ3wiQ8OZvXVrFMLRm6gramUZEQwn6db7PtcpSUZxoB6w6u/IK5BdD5H
mXUAmJhRP5AUZQ+rWRFpWNAOAzPs6GwfC57KdO44oMuTEyR7FfvNv2X5JaYCbOsM
XBL8aLHFTShdauQREECs3uovaQrBo1BNqMlC+YEdaRhO7ukit4WSeZoEFHS50YSD
nevEJ7R35Cq4s2MQ3gLU5ps5FvRLRoNN5pimy9LUWgq6W/BPGlA7mRIEtDQNu19H
YBlr6G+G/7tvycjxhIkwQ0axmbTrew==
=XZOV
-----END PGP SIGNATURE-----
Merge tag 'mhi-for-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/mani/mhi into char-misc-next
Manivannan writes:
MHI patches for v5.11
Here is the MHI patch set for v5.11. Most of the patches are cleanups and fixes
but there are some noticeable changes too:
1. Loic finally removed the auto-start option from the channel parameters of the
MHI controller. It is the duty of the client drivers like qrtr to start/stop the
channels when required, so we decided to remove this option. As a side effect,
we changed the qrtr driver to start the channels during its probe and removed
the auto-start option from ath11k controller.
**NOTE** Since these changes spawns both MHI and networking trees, the patches
are maintained in an immutable branch [1] and pulled into both mhi-next and
ath11k-next branches. The networking patches got acks from ath11k and networking
maintainers as well.
2. Loic added a generic MHI pci controller driver. This driver will be used by
the PCI based Qualcomm modems like SDX55 and exposes channels such as QMI,
IP_HW0, IPCR etc...
3. Loic fixed the MHI device hierarchy by maintaining the correct parent child
relationships. Earlier all MHI devices lived in the same level under the parent
device like PCIe. But now, the MHI devices belonging to channels will become the
children of controller MHI device.
4. Finally Loic also improved the MHI device naming by using indexed names such
as mhi0, mhi1, etc... This will break the userspace applications depending on
the old naming convention but since the only one user so far is Jeff Hugo's AI
accelerator apps, we decided to make this change now itself with his agreement.
5. Bhaumik fixed the qrtr driver by stopping the channels during remove. This
patch also got ack from networking maintainer and we decided to take it through
MHI tree (via immutable branch) since we already had a qrtr change.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/mani/mhi.git/log/?h=mhi-ath11k-immutable
* tag 'mhi-for-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/mani/mhi: (30 commits)
mhi: pci_generic: Fix implicit conversion warning
bus: mhi: core: Fix error handling in mhi_register_controller()
bus: mhi: core: Fix device hierarchy
bus: mhi: core: Indexed MHI controller name
net: qrtr: Unprepare MHI channels during remove
bus: mhi: core: Remove MHI event ring IRQ handlers when powering down
bus: mhi: core: Mark and maintain device states early on after power down
bus: mhi: core: Separate system error and power down handling
bus: mhi: core: Check for IRQ availability during registration
bus: mhi: core: Move to an error state on mission mode failure
bus: mhi: core: Use appropriate label in firmware load handler API
bus: mhi: core: Move to an error state on any firmware load failure
bus: mhi: core: Prevent sending multiple RDDM entry callbacks
bus: mhi: core: Move to SYS_ERROR regardless of RDDM capability
bus: mhi: core: Skip device wake in error or shutdown states
bus: mhi: core: Move to using high priority workqueue
bus: mhi: core: Use appropriate names for firmware load functions
bus: mhi: core: Skip RDDM download for unknown execution environment
bus: mhi: core: Rename RDDM download function to use proper words
bus: mhi: core: Remove unused mhi_fw_load_worker() declaration
...
There are a few problems with the error handling in this function. They
mostly center around the alloc_ordered_workqueue() allocation.
1) If that allocation fails or if the kcalloc() prior to it fails then
it leads to a NULL dereference when we call
destroy_workqueue(mhi_cntrl->hiprio_wq).
2) The error code is not set.
3) The "mhi_cntrl->mhi_cmd" allocation is not freed.
The error handling was slightly confusing and I re-ordered it to be in
the exact mirror/reverse order of how things were allocated. I changed
the label names to say what the goto does instead of describing where
the goto comes from.
Fixes: 8f70397876 ("bus: mhi: core: Move to using high priority workqueue")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
This patch fixes the hierarchical structure of MHI devices. Indeed,
MHI client devices are directly 'enumerated' from the mhi controller
and therefore must be direct descendants/children of their mhi
controller device, in accordance with the Linux Device Model.
Today both MHI clients and controller devices are at the same level,
this patch ensures that MHI controller is parent of its client devices.
The hierarchy is especially important for power management (safe
suspend/resume order). It is also useful for userspace to determine
relationship between MHI client devices and controllers.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Today the MHI controller name is simply cloned from the underlying
bus device (its parent), that gives the following device structure
for e.g. a MHI/PCI controller:
devices/pci0000:00/0000:00:01.2/0000:02:00.0/0000:02:00.0
devices/pci0000:00/0000:00:01.2/0000:02:00.0/0000:02:00.0/0000:02:00.0_IPCR
...
That's quite misleading/confusing and can cause device registering
issues because of duplicate dev name (e.g. if a PCI device register
two different MHI instances).
This patch changes MHI core to create indexed mhi controller names
(mhi0, mhi1...) in the same way as other busses (i2c0, usb0...).
The previous example becomes:
devices/pci0000:00/0000:00:01.2/0000:02:00.0/mhi0
devices/pci0000:00/0000:00:01.2/0000:02:00.0/mhi0/mhi0_IPCR
...
v2: move index field at the end of mhi_controller struct (before bool)
to avoid breaking well packed alignment.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Trivial conflict in CAN, keep the net-next + the byteswap wrapper.
Conflicts:
drivers/net/can/usb/gs_usb.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
kfree(dev) has been called inside put_device so anther
kfree would cause a use-after-free bug/
Fixes: 8286ae0330 ("MIPS: Add CDMM bus support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
GP Timers used as clockevent/source are not available for ti-sysc bus and
handled by Kernel timekeeping core. Now ti-sysc produces error message
every time such timer is detected:
"ti-sysc: probe of 48040000.target-module failed with error -16"
Such messages are not necessary, so suppress them by returning -ENXIO
instead of -EBUSY.
Fixes: 6cfcd5563b ("clocksource/drivers/timer-ti-dm: Fix suspend and resume for am3 and am4")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
While powering down, the device may or may not acknowledge an MHI
RESET issued by host for a graceful shutdown scenario and end up
sending an incoming data packet after tasklets have been killed.
If a rogue device sends this interrupt for a data transfer event
ring update, it can result in a tasklet getting scheduled while a
clean up is ongoing or has completed and cause access to freed
memory leading to a NULL pointer exception. Remove the interrupt
handlers for MHI event rings early on to avoid this scenario.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
mhi_power_down() does not ensure that the PM state is moved to an
inaccessible state soon enough as the system can encounter
scheduling delays till mhi_pm_disable_transition() gets called.
Additionally, if an MHI controller decides that the device is now
inaccessible and issues a power down, the register inaccessible
state is not maintained by moving from MHI_PM_LD_ERR_FATAL_DETECT
to MHI_PM_SHUTDOWN_PROCESS. This can result in bus errors if a
client driver attempted to read registers when powering down.
Close these gaps and avoid any race conditions to prevent such
activity.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Currently, there exist a set of if...else statements in the
mhi_pm_disable_transition() function which make handling system
error and disable transitions differently complex. To make that
cleaner and facilitate differences in behavior, separate these
two transitions for MHI host.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Current design allows a controller to register with MHI successfully
without the need to have any IRQs available for use. If no IRQs are
available, power up requests to MHI can fail after a successful
registration with MHI. Improve the design by checking for the number
of IRQs available sooner within the mhi_regsiter_controller() API as
it is required to be specified by the controller.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
If the host receives a mission mode event and by the time it can get
to processing it, the register accesses fail implying a connectivity
error, MHI should move to an error state. This helps avoid longer wait
times from a synchronous power up perspective and accurately reflects
the MHI execution environment and power management states.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Correct the "error_read" label to say "error_ready_state" as that
is the appropriate usage of the label.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Move MHI to a firmware download error state for a failure to find
the firmware files or to load SBL or EBL image using BHI/BHIe. This
helps detect an error state sooner and shortens the wait for a
synchronous power up timeout.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
If an mhi_power_down() is initiated after the device has entered
RDDM and a status callback was provided for it, it is possible
that another BHI interrupt fires while waiting for the MHI
RESET to be cleared. If that happens, MHI host would have moved
a "disabled" execution environment and the check to allow sending
an RDDM status callback will pass when it is should not. Add a
check to see if MHI is in an active state before proceeding.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
In some cases, the entry of device to RDDM execution environment
can occur after a significant amount of time has elapsed and a
SYS_ERROR state change event has already arrived. This can result
in scenarios where MHI controller and client drivers are unaware
of the error state of the device. Remove the check for rddm_image
when processing the SYS_ERROR state change as it is present in
mhi_pm_sys_err_handler() already and prevent further activity
until the expected RDDM execution environment change occurs or
the controller driver decides further action.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
MHI client drivers can request a device wake even if the device
may be in an error state or undergoing a shutdown. To prevent
unnecessary device wake processing, check for the device state
and bail out early so that the clients are made aware of the
device state sooner.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
MHI work is currently scheduled on the global/system workqueue and can
encounter delays on a stressed system. To avoid those unforeseen
delays which can hamper bootup or shutdown times, use a dedicated high
priority workqueue instead of the global/system workqueue.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
mhi_fw_load_sbl() function is currently used to transfer SBL or EDL
images over BHI (Boot Host Interface). Same goes with mhi_fw_load_amss()
which uses BHIe. However, the contents of these functions do not
indicate support for a specific set of images. Since these can be used
for any image download over BHI or BHIe, rename them based on the
protocol used.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
If MHI is unable to determine the execution environment during
the panic path, host must skip the RDDM download. This can happen
if the BHI offset read or the BHI_EXECENV register read fails
indicating that the underlying transport is unresponsive. Hence,
there is no need to trigger an RDDM using SYSERR or request an
SOC reset.
Suggested-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
mhi_download_rddm_img() uses a shorter version of the word image.
Expand it and rename the function to mhi_download_rddm_image().
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The mhi_fw_load_worker() function no longer exists. Remove its
declaration as part of code clean-up.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The mhi_get_exec_env() APIs can be used by the controller drivers
to query the execution environment of the MHI device. Expose it
so it can be used in some scenarios to determine behavior of
controllers.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
There is an extra 'i' counter in the mhi_firmware_copy() function
which is unused. Remove it to clean-up code and reduce stack
space as well as improve efficiency of the function.
Fixes: cd457afb16 ("bus: mhi: core: Add support for downloading firmware over BHIe")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
