We can't deal with syncookie mode yet, the syncookie rx path will create
tcp reqsk, i.e. we get OOB access because we treat tcp reqsk as mptcp reqsk one:
TCP: SYN flooding on port 20002. Sending cookies.
BUG: KASAN: slab-out-of-bounds in subflow_syn_recv_sock+0x451/0x4d0 net/mptcp/subflow.c:191
Read of size 1 at addr ffff8881167bc148 by task syz-executor099/2120
subflow_syn_recv_sock+0x451/0x4d0 net/mptcp/subflow.c:191
tcp_get_cookie_sock+0xcf/0x520 net/ipv4/syncookies.c:209
cookie_v6_check+0x15a5/0x1e90 net/ipv6/syncookies.c:252
tcp_v6_cookie_check net/ipv6/tcp_ipv6.c:1123 [inline]
[..]
Bug can be reproduced via "sysctl net.ipv4.tcp_syncookies=2".
Note that MPTCP should work with syncookies (4th ack would carry needed
state), but it appears better to sort that out in -next so do tcp
fallback for now.
I removed the MPTCP ifdef for tcp_rsk "is_mptcp" member because
if (IS_ENABLED()) is easier to read than "#ifdef IS_ENABLED()/#endif" pair.
Cc: Eric Dumazet <edumazet@google.com>
Fixes: cec37a6e41 ("mptcp: Handle MP_CAPABLE options for outgoing connections")
Reported-by: Christoph Paasch <cpaasch@apple.com>
Tested-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extends UDP GRO to support fraglist GRO/GSO
by using the previously introduced infrastructure.
If the feature is enabled, all UDP packets are going to
fraglist GRO (local input and forward).
After validating the csum, we mark ip_summed as
CHECKSUM_UNNECESSARY for fraglist GRO packets to
make sure that the csum is not touched.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add hooks to tcp_output.c to add MP_CAPABLE to an outgoing SYN request,
to capture the MP_CAPABLE in the received SYN-ACK, to add MP_CAPABLE to
the final ACK of the three-way handshake.
Use the .sk_rx_dst_set() handler in the subflow proto to capture when the
responding SYN-ACK is received and notify the MPTCP connection layer.
Co-developed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Co-developed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Peter Krystad <peter.krystad@linux.intel.com>
Signed-off-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implements the infrastructure for MPTCP sockets.
MPTCP sockets open one in-kernel TCP socket per subflow. These subflow
sockets are only managed by the MPTCP socket that owns them and are not
visible from userspace. This commit allows a userspace program to open
an MPTCP socket with:
sock = socket(AF_INET, SOCK_STREAM, IPPROTO_MPTCP);
The resulting socket is simply a wrapper around a single regular TCP
socket, without any of the MPTCP protocol implemented over the wire.
Co-developed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Co-developed-by: Peter Krystad <peter.krystad@linux.intel.com>
Signed-off-by: Peter Krystad <peter.krystad@linux.intel.com>
Co-developed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Co-developed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
if seq_file .next fuction does not change position index,
read after some lseek can generate unexpected output.
https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
in the same manner as commit d0f4185160 ("net, ip_tunnel: fix
namespaces move"), fix namespace moving as it was broken since commit
8d79266bc4 ("ip6_tunnel: add collect_md mode to IPv6 tunnel"), but for
ipv6 this time; there is no reason to keep it for ip6_tunnel.
Fixes: 8d79266bc4 ("ip6_tunnel: add collect_md mode to IPv6 tunnel")
Signed-off-by: William Dauchy <w.dauchy@criteo.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After LRO/GRO is applied, SRv6 encapsulated packets have
SKB_GSO_IPXIP6 feature flag, and this flag must be removed right after
decapulation procedure.
Currently, SKB_GSO_IPXIP6 flag is not removed on End.D* actions, which
creates inconsistent packet state, that is, a normal TCP/IP packets
have the SKB_GSO_IPXIP6 flag. This behavior can cause unexpected
fallback to GSO on routing to netdevices that do not support
SKB_GSO_IPXIP6. For example, on inter-VRF forwarding, decapsulated
packets separated into small packets by GSO because VRF devices do not
support TSO for packets with SKB_GSO_IPXIP6 flag, and this degrades
forwarding performance.
This patch removes encapsulation related GSO flags from the skb right
after the End.D* action is applied.
Fixes: d7a669dd2f ("ipv6: sr: add helper functions for seg6local")
Signed-off-by: Yuki Taguchi <tagyounit@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2020-01-21
1) Fix packet tx through bpf_redirect() for xfrm and vti
interfaces. From Nicolas Dichtel.
2) Do not confirm neighbor when do pmtu update on a virtual
xfrm interface. From Xu Wang.
3) Support output_mark for offload ESP packets, this was
forgotten when the output_mark was added initially.
From Ulrich Weber.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for moving IPv4 GRE tunnels between namespaces was added in
commit b57708add3 ("gre: add x-netns support"). The respective change
for IPv6 tunnels, commit 22f08069e8 ("ip6gre: add x-netns support")
did not drop NETIF_F_NETNS_LOCAL flag so moving them from one netns to
another is still denied in IPv6 case. Drop NETIF_F_NETNS_LOCAL flag from
ip6gre tunnels to allow moving ip6gre tunnel endpoints between network
namespaces.
Signed-off-by: Niko Kortstrom <niko.kortstrom@nokia.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 9b42c1f179 ("xfrm: Extend the output_mark") added output_mark
support but missed ESP offload support.
xfrm_smark_get() is not called within xfrm_input() for packets coming
from esp4_gro_receive() or esp6_gro_receive(). Therefore call
xfrm_smark_get() directly within these functions.
Fixes: 9b42c1f179 ("xfrm: Extend the output_mark to support input direction and masking.")
Signed-off-by: Ulrich Weber <ulrich.weber@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
In a similar fashion to previous patch, add "offload" and "trap"
indication to IPv6 routes.
This is done by using two unused bits in 'struct fib6_info' to hold
these indications. Capable drivers are expected to set these when
processing the various in-kernel route notifications.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a straight-forward conversion case for the new function,
iterating over the return value from udp_rcv_segment, which actually is
a wrapper around skb_gso_segment.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With an ebpf program that redirects packets through a vti[6] interface,
the packets are dropped because no dst is attached.
This could also be reproduced with an AF_PACKET socket, with the following
python script (vti1 is an ip_vti interface):
import socket
send_s = socket.socket(socket.AF_PACKET, socket.SOCK_RAW, 0)
# scapy
# p = IP(src='10.100.0.2', dst='10.200.0.1')/ICMP(type='echo-request')
# raw(p)
req = b'E\x00\x00\x1c\x00\x01\x00\x00@\x01e\xb2\nd\x00\x02\n\xc8\x00\x01\x08\x00\xf7\xff\x00\x00\x00\x00'
send_s.sendto(req, ('vti1', 0x800, 0, 0))
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
MPTCP will make use of tcp_send_mss() and tcp_push() when sending
data to specific TCP subflows.
tcp_request_sock_ipvX_ops and ipvX_specific will be referenced
during TCP subflow creation.
Co-developed-by: Peter Krystad <peter.krystad@linux.intel.com>
Signed-off-by: Peter Krystad <peter.krystad@linux.intel.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The argument is always ignored, so remove it.
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for userspace to specify a device index to limit the scope
of an entry via the TCP_MD5SIG_EXT setsockopt. The existing __tcpm_pad
is renamed to tcpm_ifindex and the new field is only checked if the new
TCP_MD5SIG_FLAG_IFINDEX is set in tcpm_flags. For now, the device index
must point to an L3 master device (e.g., VRF). The API and error
handling are setup to allow the constraint to be relaxed in the future
to any device index.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add l3index to tcp_md5sig_key to represent the L3 domain of a key, and
add l3index to tcp_md5_do_add and tcp_md5_do_del to fill in the key.
With the key now based on an l3index, add the new parameter to the
lookup functions and consider the l3index when looking for a match.
The l3index comes from the skb when processing ingress packets leveraging
the helpers created for socket lookups, tcp_v4_sdif and inet_iif (and the
v6 variants). When the sdif index is set it means the packet ingressed a
device that is part of an L3 domain and inet_iif points to the VRF device.
For egress, the L3 domain is determined from the socket binding and
sk_bound_dev_if.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original ingress device index is saved to the cb space of the skb
and the cb is moved during tcp processing. Since tcp_v6_inbound_md5_hash
can be called before and after the cb move, pass dif and sdif to it so
the caller can save both prior to the cb move. Both are used by a later
patch.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that mlxsw is converted to use the new FIB notifications it is
possible to delete the old ones and use the new replace / append /
delete notifications.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an entire multipath route is deleted, only emit a notification if
it is the first route in the node. Emit a replace notification in case
the last sibling is followed by another route. Otherwise, emit a delete
notification.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the purpose of route offload, when a single route is deleted, it is
only of interest if it is the first route in the node or if it is
sibling to such a route.
In the first case, distinguish between several possibilities:
1. Route is the last route in the node. Emit a delete notification
2. Route is followed by a non-multipath route. Emit a replace
notification for the non-multipath route.
3. Route is followed by a multipath route. Emit a replace notification
for the multipath route.
In the second case, only emit a delete notification to ensure the route
is no longer used as a valid nexthop.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a new listener is registered to the FIB notification chain it
receives a dump of all the available routes in the system. Instead, make
sure to only replay the IPv6 routes that are actually used in the data
path and are of any interest to the new listener.
This is done by iterating over all the routing tables in the given
namespace, but from each traversed node only the first route ('leaf') is
notified. Multipath routes are notified in a single notification instead
of one for each nexthop.
Add fib6_rt_dump_tmp() to do that. Later on in the patch set it will be
renamed to fib6_rt_dump() instead of the existing one.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a similar fashion to previous patches, only notify the new multipath
route if it is the first route in the node or if it was appended to such
route.
The type of the notification (replace vs. append) is determined based on
the number of routes added ('nhn') and the number of sibling routes. If
the two do not match, then an append notification should be sent.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to the corresponding IPv4 patch, only notify the new route if it
is replacing the currently offloaded one. Meaning, the one pointed to by
'fn->leaf'.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fib6_add_rt2node() takes care of adding a single route ('struct
fib6_info') to a FIB node. The route in question should only be notified
in case it is added as the first route in the node (lowest metric) or if
it is added as a sibling route to the first route in the node.
The first criterion can be tested by checking if the route is pointed to
by 'fn->leaf'. The second criterion can be tested by checking the new
'notify_sibling_rt' variable that is set when the route is added as a
sibling to the first route in the node.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When do IPv6 tunnel PMTU update and calls __ip6_rt_update_pmtu() in the end,
we should not call dst_confirm_neigh() as there is no two-way communication.
v5: No change.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When do IPv6 tunnel PMTU update and calls __ip6_rt_update_pmtu() in the end,
we should not call dst_confirm_neigh() as there is no two-way communication.
Although vti and vti6 are immune to this problem because they are IFF_NOARP
interfaces, as Guillaume pointed. There is still no sense to confirm neighbour
here.
v5: Update commit description.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When do tunnel PMTU update and calls __ip6_rt_update_pmtu() in the end,
we should not call dst_confirm_neigh() as there is no two-way communication.
v5: No Change.
v4: Update commit description
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Fixes: 0dec879f63 ("net: use dst_confirm_neigh for UDP, RAW, ICMP, L2TP")
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Tested-by: Guillaume Nault <gnault@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we do ipv6 gre pmtu update, we will also do neigh confirm currently.
This will cause the neigh cache be refreshed and set to REACHABLE before
xmit.
But if the remote mac address changed, e.g. device is deleted and recreated,
we will not able to notice this and still use the old mac address as the neigh
cache is REACHABLE.
Fix this by disable neigh confirm when do pmtu update
v5: No change.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Reported-by: Jianlin Shi <jishi@redhat.com>
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MTU update code is supposed to be invoked in response to real
networking events that update the PMTU. In IPv6 PMTU update function
__ip6_rt_update_pmtu() we called dst_confirm_neigh() to update neighbor
confirmed time.
But for tunnel code, it will call pmtu before xmit, like:
- tnl_update_pmtu()
- skb_dst_update_pmtu()
- ip6_rt_update_pmtu()
- __ip6_rt_update_pmtu()
- dst_confirm_neigh()
If the tunnel remote dst mac address changed and we still do the neigh
confirm, we will not be able to update neigh cache and ping6 remote
will failed.
So for this ip_tunnel_xmit() case, _EVEN_ if the MTU is changed, we
should not be invoking dst_confirm_neigh() as we have no evidence
of successful two-way communication at this point.
On the other hand it is also important to keep the neigh reachability fresh
for TCP flows, so we cannot remove this dst_confirm_neigh() call.
To fix the issue, we have to add a new bool parameter for dst_ops.update_pmtu
to choose whether we should do neigh update or not. I will add the parameter
in this patch and set all the callers to true to comply with the previous
way, and fix the tunnel code one by one on later patches.
v5: No change.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Suggested-by: David Miller <davem@davemloft.net>
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Several nf_flow_table_offload fixes from Pablo Neira Ayuso,
including adding a missing ipv6 match description.
2) Several heap overflow fixes in mwifiex from qize wang and Ganapathi
Bhat.
3) Fix uninit value in bond_neigh_init(), from Eric Dumazet.
4) Fix non-ACPI probing of nxp-nci, from Stephan Gerhold.
5) Fix use after free in tipc_disc_rcv(), from Tuong Lien.
6) Enforce limit of 33 tail calls in mips and riscv JIT, from Paul
Chaignon.
7) Multicast MAC limit test is off by one in qede, from Manish Chopra.
8) Fix established socket lookup race when socket goes from
TCP_ESTABLISHED to TCP_LISTEN, because there lacks an intervening
RCU grace period. From Eric Dumazet.
9) Don't send empty SKBs from tcp_write_xmit(), also from Eric Dumazet.
10) Fix active backup transition after link failure in bonding, from
Mahesh Bandewar.
11) Avoid zero sized hash table in gtp driver, from Taehee Yoo.
12) Fix wrong interface passed to ->mac_link_up(), from Russell King.
13) Fix DSA egress flooding settings in b53, from Florian Fainelli.
14) Memory leak in gmac_setup_txqs(), from Navid Emamdoost.
15) Fix double free in dpaa2-ptp code, from Ioana Ciornei.
16) Reject invalid MTU values in stmmac, from Jose Abreu.
17) Fix refcount leak in error path of u32 classifier, from Davide
Caratti.
18) Fix regression causing iwlwifi firmware crashes on boot, from Anders
Kaseorg.
19) Fix inverted return value logic in llc2 code, from Chan Shu Tak.
20) Disable hardware GRO when XDP is attached to qede, frm Manish
Chopra.
21) Since we encode state in the low pointer bits, dst metrics must be
at least 4 byte aligned, which is not necessarily true on m68k. Add
annotations to fix this, from Geert Uytterhoeven.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (160 commits)
sfc: Include XDP packet headroom in buffer step size.
sfc: fix channel allocation with brute force
net: dst: Force 4-byte alignment of dst_metrics
selftests: pmtu: fix init mtu value in description
hv_netvsc: Fix unwanted rx_table reset
net: phy: ensure that phy IDs are correctly typed
mod_devicetable: fix PHY module format
qede: Disable hardware gro when xdp prog is installed
net: ena: fix issues in setting interrupt moderation params in ethtool
net: ena: fix default tx interrupt moderation interval
net/smc: unregister ib devices in reboot_event
net: stmmac: platform: Fix MDIO init for platforms without PHY
llc2: Fix return statement of llc_stat_ev_rx_null_dsap_xid_c (and _test_c)
net: hisilicon: Fix a BUG trigered by wrong bytes_compl
net: dsa: ksz: use common define for tag len
s390/qeth: don't return -ENOTSUPP to userspace
s390/qeth: fix promiscuous mode after reset
s390/qeth: handle error due to unsupported transport mode
cxgb4: fix refcount init for TC-MQPRIO offload
tc-testing: initial tdc selftests for cls_u32
...
In commit 4b1373de73 ("net: ipv6: addr: perform strict checks also for
doit handlers") we add strict check for inet6_rtm_getaddr(). But we did
the invalid header values check before checking if NETLINK_F_STRICT_CHK
is set. This may break backwards compatibility if user already set the
ifm->ifa_prefixlen, ifm->ifa_flags, ifm->ifa_scope in their netlink code.
I didn't move the nlmsg_len check because I thought it's a valid check.
Reported-by: Jianlin Shi <jishi@redhat.com>
Fixes: 4b1373de73 ("net: ipv6: addr: perform strict checks also for doit handlers")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Replace all the occurrences of FIELD_SIZEOF() with sizeof_field() except
at places where these are defined. Later patches will remove the unused
definition of FIELD_SIZEOF().
This patch is generated using following script:
EXCLUDE_FILES="include/linux/stddef.h|include/linux/kernel.h"
git grep -l -e "\bFIELD_SIZEOF\b" | while read file;
do
if [[ "$file" =~ $EXCLUDE_FILES ]]; then
continue
fi
sed -i -e 's/\bFIELD_SIZEOF\b/sizeof_field/g' $file;
done
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Link: https://lore.kernel.org/r/20190924105839.110713-3-pankaj.laxminarayan.bharadiya@intel.com
Co-developed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: David Miller <davem@davemloft.net> # for net
ipv6_stub uses the ip6_dst_lookup function to allow other modules to
perform IPv6 lookups. However, this function skips the XFRM layer
entirely.
All users of ipv6_stub->ip6_dst_lookup use ip_route_output_flow (via the
ip_route_output_key and ip_route_output helpers) for their IPv4 lookups,
which calls xfrm_lookup_route(). This patch fixes this inconsistent
behavior by switching the stub to ip6_dst_lookup_flow, which also calls
xfrm_lookup_route().
This requires some changes in all the callers, as these two functions
take different arguments and have different return types.
Fixes: 5f81bd2e5d ("ipv6: export a stub for IPv6 symbols used by vxlan")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will be used in the conversion of ipv6_stub to ip6_dst_lookup_flow,
as some modules currently pass a net argument without a socket to
ip6_dst_lookup. This is equivalent to commit 343d60aada ("ipv6: change
ipv6_stub_impl.ipv6_dst_lookup to take net argument").
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Note that the sysctl write accessor functions guarantee that:
net->ipv4.sysctl_ip_prot_sock <= net->ipv4.ip_local_ports.range[0]
invariant is maintained, and as such the max() in selinux hooks is actually spurious.
ie. even though
if (snum < max(inet_prot_sock(sock_net(sk)), low) || snum > high) {
per logic is the same as
if ((snum < inet_prot_sock(sock_net(sk)) && snum < low) || snum > high) {
it is actually functionally equivalent to:
if (snum < low || snum > high) {
which is equivalent to:
if (snum < inet_prot_sock(sock_net(sk)) || snum < low || snum > high) {
even though the first clause is spurious.
But we want to hold on to it in case we ever want to change what what
inet_port_requires_bind_service() means (for example by changing
it from a, by default, [0..1024) range to some sort of set).
Test: builds, git 'grep inet_prot_sock' finds no other references
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor conflict in drivers/s390/net/qeth_l2_main.c, kept the lock
from commit c8183f5489 ("s390/qeth: fix potential deadlock on
workqueue flush"), removed the code which was removed by commit
9897d583b0 ("s390/qeth: consolidate some duplicated HW cmd code").
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
End.DT6 behavior makes use of seg6_lookup_nexthop() function which drops
all packets that are destined to be locally processed. However, DT* should
be able to deliver decapsulated packets that are destined to local
addresses. Function seg6_lookup_nexthop() is also used by DX6, so in order
to maintain compatibility I created another routing helper function which
is called seg6_lookup_any_nexthop(). This function is able to take into
account both packets that have to be processed locally and the ones that
are destined to be forwarded directly to another machine. Hence,
seg6_lookup_any_nexthop() is used in DT6 rather than seg6_lookup_nexthop()
to allow local delivery.
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
NET_RAW is less dangerous, so more likely to be available to a process,
so check it first to prevent some spurious logging.
This matches IP_TRANSPARENT which checks NET_RAW first.
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing RX batch packet processing, we currently always repeat
the route lookup for each ingress packet. When no custom rules are
in place, and there aren't routes depending on source addresses,
we know that packets with the same destination address will use
the same dst.
This change tries to avoid per packet route lookup caching
the destination address of the latest successful lookup, and
reusing it for the next packet when the above conditions are
in place. Ingress traffic for most servers should fit.
The measured performance delta under UDP flood vs a recvmmsg
receiver is as follow:
vanilla patched delta
Kpps Kpps %
1431 1674 +17
In the worst-case scenario - each packet has a different
destination address - the performance delta is within noise
range.
v3 -> v4:
- support hints for SUBFLOW build, too (David A.)
- several style fixes (Eric)
v2 -> v3:
- add fib6_has_custom_rules() helpers (David A.)
- add ip6_extract_route_hint() helper (Edward C.)
- use hint directly in ip6_list_rcv_finish() (Willem)
v1 -> v2:
- fix build issue with !CONFIG_IPV6_MULTIPLE_TABLES
- fix potential race when fib6_has_custom_rules is set
while processing a packet batch
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a per namespace counter, increment it on successful creation
of any route using the source address, decrement it on deletion
of such routes.
This allows us to check easily if the routing decision in the
current namespace depends on the packet source. Will be used
by the next patch.
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style. This fixes various indentation mixups (seven spaces,
tab+one space, etc).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously we will return directly if (!rt || !rt->fib6_nh.fib_nh_gw_family)
in function rt6_probe(), but after commit cc3a86c802
("ipv6: Change rt6_probe to take a fib6_nh"), the logic changed to
return if there is fib_nh_gw_family.
Fixes: cc3a86c802 ("ipv6: Change rt6_probe to take a fib6_nh")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next:
1) Wildcard support for the net,iface set from Kristian Evensen.
2) Offload support for matching on the input interface.
3) Simplify matching on vlan header fields.
4) Add nft_payload_rebuild_vlan_hdr() function to rebuild the vlan
header from the vlan sk_buff metadata.
5) Pass extack to nft_flow_cls_offload_setup().
6) Add C-VLAN matching support.
7) Use time64_t in xt_time to fix y2038 overflow, from Arnd Bergmann.
8) Use time_t in nft_meta to fix y2038 overflow, also from Arnd.
9) Add flow_action_entry_next() helper function to flowtable offload
infrastructure.
10) Add IPv6 support to the flowtable offload infrastructure.
11) Support for input interface matching from postrouting,
from Phil Sutter.
12) Missing check for ndo callback in flowtable offload, from wenxu.
13) Remove conntrack parameter from flow_offload_fill_dir(), from wenxu.
14) Do not pass flow_rule object for rule removal, cookie is sufficient
to achieve this.
15) Release flow_rule object in case of error from the offload commit
path.
16) Undo offload ruleset updates if transaction fails.
17) Check for error when binding flowtable callbacks, from wenxu.
18) Always unbind flowtable callbacks when unregistering hooks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
in the receive path (more precisely in ip6_rcv_core()) the
skb->transport_header is set to skb->network_header + sizeof(*hdr). As a
consequence, after routing operations, destination input expects to find
skb->transport_header correctly set to the next protocol (or extension
header) that follows the network protocol. However, decap behaviors (DX*,
DT*) remove the outer IPv6 and SRH extension and do not set again the
skb->transport_header pointer correctly. For this reason, the patch sets
the skb->transport_header to the skb->network_header + sizeof(hdr) in each
DX* and DT* behavior.
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
pskb_may_pull may change pointers in header. For this reason, it is
mandatory to reload any pointer that points into skb header.
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of generally passing NULL to NF_HOOK_COND() for input device,
pass skb->dev which contains input device for routed skbs.
Note that iptables (both legacy and nft) reject rules with input
interface match from being added to POSTROUTING chains, but nftables
allows this.
Cc: Eric Garver <eric@garver.life>
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add nf_flow_rule_route_ipv6() and use it from the IPv6 and the inet
flowtable type definitions. Rename the nf_flow_rule_route() function to
nf_flow_rule_route_ipv4().
Adjust maximum number of actions, which now becomes 16 to leave
sufficient room for the IPv6 address mangling for NAT.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds the dataplane hardware offload to the flowtable
infrastructure. Three new flags represent the hardware state of this
flow:
* FLOW_OFFLOAD_HW: This flow entry resides in the hardware.
* FLOW_OFFLOAD_HW_DYING: This flow entry has been scheduled to be remove
from hardware. This might be triggered by either packet path (via TCP
RST/FIN packet) or via aging.
* FLOW_OFFLOAD_HW_DEAD: This flow entry has been already removed from
the hardware, the software garbage collector can remove it from the
software flowtable.
This patch supports for:
* IPv4 only.
* Aging via FLOW_CLS_STATS, no packet and byte counter synchronization
at this stage.
This patch also adds the action callback that specifies how to convert
the flow entry into the flow_rule object that is passed to the driver.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the NFTA_FLOWTABLE_FLAGS attribute that allows users to
specify the NF_FLOWTABLE_HW_OFFLOAD flag. This patch also adds a new
setup interface for the flowtable type to perform the flowtable offload
block callback configuration.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
One conflict in the BPF samples Makefile, some fixes in 'net' whilst
we were converting over to Makefile.target rules in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
While looking at a syzbot KCSAN report [1], I found multiple
issues in this code :
1) fib6_nh->last_probe has an initial value of 0.
While probably okay on 64bit kernels, this causes an issue
on 32bit kernels since the time_after(jiffies, 0 + interval)
might be false ~24 days after boot (for HZ=1000)
2) The data-race found by KCSAN
I could use READ_ONCE() and WRITE_ONCE(), but we also can
take the opportunity of not piling-up too many rt6_probe_deferred()
works by using instead cmpxchg() so that only one cpu wins the race.
[1]
BUG: KCSAN: data-race in find_match / find_match
write to 0xffff8880bb7aabe8 of 8 bytes by interrupt on cpu 1:
rt6_probe net/ipv6/route.c:663 [inline]
find_match net/ipv6/route.c:757 [inline]
find_match+0x5bd/0x790 net/ipv6/route.c:733
__find_rr_leaf+0xe3/0x780 net/ipv6/route.c:831
find_rr_leaf net/ipv6/route.c:852 [inline]
rt6_select net/ipv6/route.c:896 [inline]
fib6_table_lookup+0x383/0x650 net/ipv6/route.c:2164
ip6_pol_route+0xee/0x5c0 net/ipv6/route.c:2200
ip6_pol_route_output+0x48/0x60 net/ipv6/route.c:2452
fib6_rule_lookup+0x3d6/0x470 net/ipv6/fib6_rules.c:117
ip6_route_output_flags_noref+0x16b/0x230 net/ipv6/route.c:2484
ip6_route_output_flags+0x50/0x1a0 net/ipv6/route.c:2497
ip6_dst_lookup_tail+0x25d/0xc30 net/ipv6/ip6_output.c:1049
ip6_dst_lookup_flow+0x68/0x120 net/ipv6/ip6_output.c:1150
inet6_csk_route_socket+0x2f7/0x420 net/ipv6/inet6_connection_sock.c:106
inet6_csk_xmit+0x91/0x1f0 net/ipv6/inet6_connection_sock.c:121
__tcp_transmit_skb+0xe81/0x1d60 net/ipv4/tcp_output.c:1169
tcp_transmit_skb net/ipv4/tcp_output.c:1185 [inline]
tcp_xmit_probe_skb+0x19b/0x1d0 net/ipv4/tcp_output.c:3735
read to 0xffff8880bb7aabe8 of 8 bytes by interrupt on cpu 0:
rt6_probe net/ipv6/route.c:657 [inline]
find_match net/ipv6/route.c:757 [inline]
find_match+0x521/0x790 net/ipv6/route.c:733
__find_rr_leaf+0xe3/0x780 net/ipv6/route.c:831
find_rr_leaf net/ipv6/route.c:852 [inline]
rt6_select net/ipv6/route.c:896 [inline]
fib6_table_lookup+0x383/0x650 net/ipv6/route.c:2164
ip6_pol_route+0xee/0x5c0 net/ipv6/route.c:2200
ip6_pol_route_output+0x48/0x60 net/ipv6/route.c:2452
fib6_rule_lookup+0x3d6/0x470 net/ipv6/fib6_rules.c:117
ip6_route_output_flags_noref+0x16b/0x230 net/ipv6/route.c:2484
ip6_route_output_flags+0x50/0x1a0 net/ipv6/route.c:2497
ip6_dst_lookup_tail+0x25d/0xc30 net/ipv6/ip6_output.c:1049
ip6_dst_lookup_flow+0x68/0x120 net/ipv6/ip6_output.c:1150
inet6_csk_route_socket+0x2f7/0x420 net/ipv6/inet6_connection_sock.c:106
inet6_csk_xmit+0x91/0x1f0 net/ipv6/inet6_connection_sock.c:121
__tcp_transmit_skb+0xe81/0x1d60 net/ipv4/tcp_output.c:1169
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 18894 Comm: udevd Not tainted 5.4.0-rc3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: cc3a86c802 ("ipv6: Change rt6_probe to take a fib6_nh")
Fixes: f547fac624 ("ipv6: rate-limit probes for neighbourless routes")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk->sk_ack_backlog can be read without any lock being held.
We need to use READ_ONCE()/WRITE_ONCE() to avoid load/store tearing
and/or potential KCSAN warnings.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same code which recognizes ICMP error packets is duplicated several
times. Use the icmp_is_err() and icmpv6_is_err() helpers instead, which
do the same thing.
ip_multipath_l3_keys() and tcf_nat_act() didn't check for all the error types,
assume that they should instead.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Faster jhash2() can be used instead of jhash(), since
IPv6 addresses have the needed alignment requirement.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
traceroute6 output can be confusing, in that it shows the address
that a router would use to reach the sender, rather than the address
the packet used to reach the router.
Consider this case:
------------------------ N2
| |
------ ------ N3 ----
| R1 | | R2 |------|H2|
------ ------ ----
| |
------------------------ N1
|
----
|H1|
----
where H1's default route is through R1, and R1's default route is
through R2 over N2.
traceroute6 from H1 to H2 shows R2's address on N1 rather than on N2.
The script below can be used to reproduce this scenario.
traceroute6 output without this patch:
traceroute to 2000:103::4 (2000:103::4), 30 hops max, 80 byte packets
1 2000:101::1 (2000:101::1) 0.036 ms 0.008 ms 0.006 ms
2 2000:101::2 (2000:101::2) 0.011 ms 0.008 ms 0.007 ms
3 2000:103::4 (2000:103::4) 0.013 ms 0.010 ms 0.009 ms
traceroute6 output with this patch:
traceroute to 2000:103::4 (2000:103::4), 30 hops max, 80 byte packets
1 2000:101::1 (2000:101::1) 0.056 ms 0.019 ms 0.006 ms
2 2000:102::2 (2000:102::2) 0.013 ms 0.008 ms 0.008 ms
3 2000:103::4 (2000:103::4) 0.013 ms 0.009 ms 0.009 ms
#!/bin/bash
#
# ------------------------ N2
# | |
# ------ ------ N3 ----
# | R1 | | R2 |------|H2|
# ------ ------ ----
# | |
# ------------------------ N1
# |
# ----
# |H1|
# ----
#
# N1: 2000:101::/64
# N2: 2000:102::/64
# N3: 2000:103::/64
#
# R1's host part of address: 1
# R2's host part of address: 2
# H1's host part of address: 3
# H2's host part of address: 4
#
# For example:
# the IPv6 address of R1's interface on N2 is 2000:102::1/64
#
# Nets are implemented by macvlan interfaces (bridge mode) over
# dummy interfaces.
#
# Create net namespaces
ip netns add host1
ip netns add host2
ip netns add rtr1
ip netns add rtr2
# Create nets
ip link add net1 type dummy; ip link set net1 up
ip link add net2 type dummy; ip link set net2 up
ip link add net3 type dummy; ip link set net3 up
# Add interfaces to net1, move them to their nemaspaces
ip link add link net1 dev host1net1 type macvlan mode bridge
ip link set host1net1 netns host1
ip link add link net1 dev rtr1net1 type macvlan mode bridge
ip link set rtr1net1 netns rtr1
ip link add link net1 dev rtr2net1 type macvlan mode bridge
ip link set rtr2net1 netns rtr2
# Add interfaces to net2, move them to their nemaspaces
ip link add link net2 dev rtr1net2 type macvlan mode bridge
ip link set rtr1net2 netns rtr1
ip link add link net2 dev rtr2net2 type macvlan mode bridge
ip link set rtr2net2 netns rtr2
# Add interfaces to net3, move them to their nemaspaces
ip link add link net3 dev rtr2net3 type macvlan mode bridge
ip link set rtr2net3 netns rtr2
ip link add link net3 dev host2net3 type macvlan mode bridge
ip link set host2net3 netns host2
# Configure interfaces and routes in host1
ip netns exec host1 ip link set lo up
ip netns exec host1 ip link set host1net1 up
ip netns exec host1 ip -6 addr add 2000:101::3/64 dev host1net1
ip netns exec host1 ip -6 route add default via 2000:101::1
# Configure interfaces and routes in rtr1
ip netns exec rtr1 ip link set lo up
ip netns exec rtr1 ip link set rtr1net1 up
ip netns exec rtr1 ip -6 addr add 2000:101::1/64 dev rtr1net1
ip netns exec rtr1 ip link set rtr1net2 up
ip netns exec rtr1 ip -6 addr add 2000:102::1/64 dev rtr1net2
ip netns exec rtr1 ip -6 route add default via 2000:102::2
ip netns exec rtr1 sysctl net.ipv6.conf.all.forwarding=1
# Configure interfaces and routes in rtr2
ip netns exec rtr2 ip link set lo up
ip netns exec rtr2 ip link set rtr2net1 up
ip netns exec rtr2 ip -6 addr add 2000:101::2/64 dev rtr2net1
ip netns exec rtr2 ip link set rtr2net2 up
ip netns exec rtr2 ip -6 addr add 2000:102::2/64 dev rtr2net2
ip netns exec rtr2 ip link set rtr2net3 up
ip netns exec rtr2 ip -6 addr add 2000:103::2/64 dev rtr2net3
ip netns exec rtr2 sysctl net.ipv6.conf.all.forwarding=1
# Configure interfaces and routes in host2
ip netns exec host2 ip link set lo up
ip netns exec host2 ip link set host2net3 up
ip netns exec host2 ip -6 addr add 2000:103::4/64 dev host2net3
ip netns exec host2 ip -6 route add default via 2000:103::2
# Ping host2 from host1
ip netns exec host1 ping6 -c5 2000:103::4
# Traceroute host2 from host1
ip netns exec host1 traceroute6 2000:103::4
# Delete nets
ip link del net3
ip link del net2
ip link del net1
# Delete namespaces
ip netns del rtr2
ip netns del rtr1
ip netns del host2
ip netns del host1
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Original-patch-by: Honggang Xu <hxu@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only slightly tricky merge conflict was the netdevsim because the
mutex locking fix overlapped a lot of driver reload reorganization.
The rest were (relatively) trivial in nature.
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot triggered struct net NULL deref in NF_HOOK_LIST:
RIP: 0010:NF_HOOK_LIST include/linux/netfilter.h:331 [inline]
RIP: 0010:ip6_sublist_rcv+0x5c9/0x930 net/ipv6/ip6_input.c:292
ipv6_list_rcv+0x373/0x4b0 net/ipv6/ip6_input.c:328
__netif_receive_skb_list_ptype net/core/dev.c:5274 [inline]
Reason:
void ipv6_list_rcv(struct list_head *head, struct packet_type *pt,
struct net_device *orig_dev)
[..]
list_for_each_entry_safe(skb, next, head, list) {
/* iterates list */
skb = ip6_rcv_core(skb, dev, net);
/* ip6_rcv_core drops skb -> NULL is returned */
if (skb == NULL)
continue;
[..]
}
/* sublist is empty -> curr_net is NULL */
ip6_sublist_rcv(&sublist, curr_dev, curr_net);
Before the recent change NF_HOOK_LIST did a list iteration before
struct net deref, i.e. it was a no-op in the empty list case.
List iteration now happens after *net deref, causing crash.
Follow the same pattern as the ip(v6)_list_rcv loop and add a list_empty
test for the final sublist dispatch too.
Cc: Edward Cree <ecree@solarflare.com>
Reported-by: syzbot+c54f457cad330e57e967@syzkaller.appspotmail.com
Fixes: ca58fbe06c ("netfilter: add and use nf_hook_slow_list()")
Signed-off-by: Florian Westphal <fw@strlen.de>
Tested-by: Leon Romanovsky <leonro@mellanox.com>
Tested-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check for !md doens't really work for ip_tunnel_info_opts(info) which
only does info + 1. Also to avoid out-of-bounds access on info, it should
ensure options_len is not less than erspan_metadata in both erspan_xmit()
and ip6erspan_tunnel_xmit().
Fixes: 1a66a836da ("gre: add collect_md mode to ERSPAN tunnel")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for net-next,
more specifically:
* Updates for ipset:
1) Coding style fix for ipset comment extension, from Jeremy Sowden.
2) De-inline many functions in ipset, from Jeremy Sowden.
3) Move ipset function definition from header to source file.
4) Move ip_set_put_flags() to source, export it as a symbol, remove
inline.
5) Move range_to_mask() to the source file where this is used.
6) Move ip_set_get_ip_port() to the source file where this is used.
* IPVS selftests and netns improvements:
7) Two patches to speedup ipvs netns dismantle, from Haishuang Yan.
8) Three patches to add selftest script for ipvs, also from
Haishuang Yan.
* Conntrack updates and new nf_hook_slow_list() function:
9) Document ct ecache extension, from Florian Westphal.
10) Skip ct extensions from ctnetlink dump, from Florian.
11) Free ct extension immediately, from Florian.
12) Skip access to ecache extension from nf_ct_deliver_cached_events()
this is not correct as reported by Syzbot.
13) Add and use nf_hook_slow_list(), from Florian.
* Flowtable infrastructure updates:
14) Move priority to nf_flowtable definition.
15) Dynamic allocation of per-device hooks in flowtables.
16) Allow to include netdevice only once in flowtable definitions.
17) Rise maximum number of devices per flowtable.
* Netfilter hardware offload infrastructure updates:
18) Add nft_flow_block_chain() helper function.
19) Pass callback list to nft_setup_cb_call().
20) Add nft_flow_cls_offload_setup() helper function.
21) Remove rules for the unregistered device via netdevice event.
22) Support for multiple devices in a basechain definition at the
ingress hook.
22) Add nft_chain_offload_cmd() helper function.
23) Add nft_flow_block_offload_init() helper function.
24) Rewind in case of failing to bind multiple devices to hook.
25) Typo in IPv6 tproxy module description, from Norman Rasmussen.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Include <net/addrconf.h> for the missing declarations of
various functions. Fixes the following sparse warnings:
net/ipv6/addrconf_core.c:94:5: warning: symbol 'register_inet6addr_notifier' was not declared. Should it be static?
net/ipv6/addrconf_core.c💯5: warning: symbol 'unregister_inet6addr_notifier' was not declared. Should it be static?
net/ipv6/addrconf_core.c:106:5: warning: symbol 'inet6addr_notifier_call_chain' was not declared. Should it be static?
net/ipv6/addrconf_core.c:112:5: warning: symbol 'register_inet6addr_validator_notifier' was not declared. Should it be static?
net/ipv6/addrconf_core.c:118:5: warning: symbol 'unregister_inet6addr_validator_notifier' was not declared. Should it be static?
net/ipv6/addrconf_core.c:125:5: warning: symbol 'inet6addr_validator_notifier_call_chain' was not declared. Should it be static?
net/ipv6/addrconf_core.c:237:6: warning: symbol 'in6_dev_finish_destroy' was not declared. Should it be static?
Signed-off-by: Ben Dooks (Codethink) <ben.dooks@codethink.co.uk>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Thomas found that some forwarded packets would be stuck
in FQ packet scheduler because their skb->tstamp contained
timestamps far in the future.
We thought we addressed this point in commit 8203e2d844
("net: clear skb->tstamp in forwarding paths") but there
is still an issue when/if a packet needs to be fragmented.
In order to meet EDT requirements, we have to make sure all
fragments get the original skb->tstamp.
Note that this original skb->tstamp should be zero in
forwarding path, but might have a non zero value in
output path if user decided so.
Fixes: fb420d5d91 ("tcp/fq: move back to CLOCK_MONOTONIC")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Thomas Bartschies <Thomas.Bartschies@cvk.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit b0818f80c8.
Started seeing weird behavior after this patch especially in
the IPv6 code path. Haven't root caused it, but since this was
applied to net branch, taking a precautionary measure to revert
it and look / analyze those failures
Revert this now and I'll send a better fix after analysing / fixing
the weirdness observed.
CC: Eric Dumazet <edumazet@google.com>
CC: Wei Wang <weiwan@google.com>
CC: David S. Miller <davem@davemloft.net>
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While invalidating the dst, we assign backhole_netdev instead of
loopback device. However, this device does not have idev pointer
and hence no ip6_ptr even if IPv6 is enabled. Possibly this has
triggered the syzbot reported crash.
The syzbot report does not have reproducer, however, this is the
only device that doesn't have matching idev created.
Crash instruction is :
static inline bool ip6_ignore_linkdown(const struct net_device *dev)
{
const struct inet6_dev *idev = __in6_dev_get(dev);
return !!idev->cnf.ignore_routes_with_linkdown; <= crash
}
Also ipv6 always assumes presence of idev and never checks for it
being NULL (as does the above referenced code). So adding a idev
for the blackhole_netdev to avoid this class of crashes in the future.
Signed-off-by: David S. Miller <davem@davemloft.net>
There are few places where we fetch tp->write_seq while
this field can change from IRQ or other cpu.
We need to add READ_ONCE() annotations, and also make
sure write sides use corresponding WRITE_ONCE() to avoid
store-tearing.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are few places where we fetch tp->copied_seq while
this field can change from IRQ or other cpu.
We need to add READ_ONCE() annotations, and also make
sure write sides use corresponding WRITE_ONCE() to avoid
store-tearing.
Note that tcp_inq_hint() was already using READ_ONCE(tp->copied_seq)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are few places where we fetch tp->rcv_nxt while
this field can change from IRQ or other cpu.
We need to add READ_ONCE() annotations, and also make
sure write sides use corresponding WRITE_ONCE() to avoid
store-tearing.
Note that tcp_inq_hint() was already using READ_ONCE(tp->rcv_nxt)
syzbot reported :
BUG: KCSAN: data-race in tcp_poll / tcp_queue_rcv
write to 0xffff888120425770 of 4 bytes by interrupt on cpu 0:
tcp_rcv_nxt_update net/ipv4/tcp_input.c:3365 [inline]
tcp_queue_rcv+0x180/0x380 net/ipv4/tcp_input.c:4638
tcp_rcv_established+0xbf1/0xf50 net/ipv4/tcp_input.c:5616
tcp_v4_do_rcv+0x381/0x4e0 net/ipv4/tcp_ipv4.c:1542
tcp_v4_rcv+0x1a03/0x1bf0 net/ipv4/tcp_ipv4.c:1923
ip_protocol_deliver_rcu+0x51/0x470 net/ipv4/ip_input.c:204
ip_local_deliver_finish+0x110/0x140 net/ipv4/ip_input.c:231
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_local_deliver+0x133/0x210 net/ipv4/ip_input.c:252
dst_input include/net/dst.h:442 [inline]
ip_rcv_finish+0x121/0x160 net/ipv4/ip_input.c:413
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_rcv+0x18f/0x1a0 net/ipv4/ip_input.c:523
__netif_receive_skb_one_core+0xa7/0xe0 net/core/dev.c:5004
__netif_receive_skb+0x37/0xf0 net/core/dev.c:5118
netif_receive_skb_internal+0x59/0x190 net/core/dev.c:5208
napi_skb_finish net/core/dev.c:5671 [inline]
napi_gro_receive+0x28f/0x330 net/core/dev.c:5704
receive_buf+0x284/0x30b0 drivers/net/virtio_net.c:1061
read to 0xffff888120425770 of 4 bytes by task 7254 on cpu 1:
tcp_stream_is_readable net/ipv4/tcp.c:480 [inline]
tcp_poll+0x204/0x6b0 net/ipv4/tcp.c:554
sock_poll+0xed/0x250 net/socket.c:1256
vfs_poll include/linux/poll.h:90 [inline]
ep_item_poll.isra.0+0x90/0x190 fs/eventpoll.c:892
ep_send_events_proc+0x113/0x5c0 fs/eventpoll.c:1749
ep_scan_ready_list.constprop.0+0x189/0x500 fs/eventpoll.c:704
ep_send_events fs/eventpoll.c:1793 [inline]
ep_poll+0xe3/0x900 fs/eventpoll.c:1930
do_epoll_wait+0x162/0x180 fs/eventpoll.c:2294
__do_sys_epoll_pwait fs/eventpoll.c:2325 [inline]
__se_sys_epoll_pwait fs/eventpoll.c:2311 [inline]
__x64_sys_epoll_pwait+0xcd/0x170 fs/eventpoll.c:2311
do_syscall_64+0xcf/0x2f0 arch/x86/entry/common.c:296
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 7254 Comm: syz-fuzzer Not tainted 5.3.0+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both tcp_v4_err() and tcp_v6_err() do the following operations
while they do not own the socket lock :
fastopen = tp->fastopen_rsk;
snd_una = fastopen ? tcp_rsk(fastopen)->snt_isn : tp->snd_una;
The problem is that without appropriate barrier, the compiler
might reload tp->fastopen_rsk and trigger a NULL deref.
request sockets are protected by RCU, we can simply add
the missing annotations and barriers to solve the issue.
Fixes: 168a8f5805 ("tcp: TCP Fast Open Server - main code path")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6erspan driver calls ether_setup(), after commit 61e84623ac
("net: centralize net_device min/max MTU checking"), the range
of mtu is [min_mtu, max_mtu], which is [68, 1500] by default.
It causes the dev mtu of the erspan device to not be greater
than 1500, this limit value is not correct for ip6erspan tap
device.
Fixes: 61e84623ac ("net: centralize net_device min/max MTU checking")
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Acked-by: William Tu <u9012063@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Rajendra reported a kernel panic when a link was taken down:
[ 6870.263084] BUG: unable to handle kernel NULL pointer dereference at 00000000000000a8
[ 6870.271856] IP: [<ffffffff8efc5764>] __ipv6_ifa_notify+0x154/0x290
<snip>
[ 6870.570501] Call Trace:
[ 6870.573238] [<ffffffff8efc58c6>] ? ipv6_ifa_notify+0x26/0x40
[ 6870.579665] [<ffffffff8efc98ec>] ? addrconf_dad_completed+0x4c/0x2c0
[ 6870.586869] [<ffffffff8efe70c6>] ? ipv6_dev_mc_inc+0x196/0x260
[ 6870.593491] [<ffffffff8efc9c6a>] ? addrconf_dad_work+0x10a/0x430
[ 6870.600305] [<ffffffff8f01ade4>] ? __switch_to_asm+0x34/0x70
[ 6870.606732] [<ffffffff8ea93a7a>] ? process_one_work+0x18a/0x430
[ 6870.613449] [<ffffffff8ea93d6d>] ? worker_thread+0x4d/0x490
[ 6870.619778] [<ffffffff8ea93d20>] ? process_one_work+0x430/0x430
[ 6870.626495] [<ffffffff8ea99dd9>] ? kthread+0xd9/0xf0
[ 6870.632145] [<ffffffff8f01ade4>] ? __switch_to_asm+0x34/0x70
[ 6870.638573] [<ffffffff8ea99d00>] ? kthread_park+0x60/0x60
[ 6870.644707] [<ffffffff8f01ae77>] ? ret_from_fork+0x57/0x70
[ 6870.650936] Code: 31 c0 31 d2 41 b9 20 00 08 02 b9 09 00 00 0
addrconf_dad_work is kicked to be scheduled when a device is brought
up. There is a race between addrcond_dad_work getting scheduled and
taking the rtnl lock and a process taking the link down (under rtnl).
The latter removes the host route from the inet6_addr as part of
addrconf_ifdown which is run for NETDEV_DOWN. The former attempts
to use the host route in __ipv6_ifa_notify. If the down event removes
the host route due to the race to the rtnl, then the BUG listed above
occurs.
Since the DAD sequence can not be aborted, add a check for the missing
host route in __ipv6_ifa_notify. The only way this should happen is due
to the previously mentioned race. The host route is created when the
address is added to an interface; it is only removed on a down event
where the address is kept. Add a warning if the host route is missing
AND the device is up; this is a situation that should never happen.
Fixes: f1705ec197 ("net: ipv6: Make address flushing on ifdown optional")
Reported-by: Rajendra Dendukuri <rajendra.dendukuri@broadcom.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit a3ce2a21bb.
Eric reported tests failings with commit. After digging into it,
the bottom line is that the DAD sequence is not to be messed with.
There are too many cases that are expected to proceed regardless
of whether a device is up.
Revert the patch and I will send a different solution for the
problem Rajendra reported.
Signed-off-by: David Ahern <dsahern@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since errors are propagated all the way up to the caller, propagate
possible extack of the caller all the way down to the notifier block
callback.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike events for registered notifier, during the registration, the
errors that happened for the block being registered are not propagated
up to the caller. Make sure the error is propagated for FIB rules and
entries.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently all users of FIB notifier only cares about events in init_net.
Later in this patchset, users get interested in other namespaces too.
However, for every registered block user is interested only about one
namespace. Make the FIB notifier registration per-netns and avoid
unnecessary calls of notifier block for other namespaces.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to this change an application sending <= 1MSS worth of data and
enabling UDP GSO would fail if the system had SW GSO enabled, but the
same send would succeed if HW GSO offload is enabled. In addition to this
inconsistency the error in the SW GSO case does not get back to the
application if sending out of a real device so the user is unaware of this
failure.
With this change we only perform GSO if the # of segments is > 1 even
if the application has enabled segmentation. I've also updated the
relevant udpgso selftests.
Fixes: bec1f6f697 ("udp: generate gso with UDP_SEGMENT")
Signed-off-by: Josh Hunt <johunt@akamai.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit dfec0ee22c ("udp: Record gso_segs when supporting UDP segmentation offload")
added gso_segs calculation, but incorrectly got sizeof() the pointer and
not the underlying data type. In addition let's fix the v6 case.
Fixes: bec1f6f697 ("udp: generate gso with UDP_SEGMENT")
Fixes: dfec0ee22c ("udp: Record gso_segs when supporting UDP segmentation offload")
Signed-off-by: Josh Hunt <johunt@akamai.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This began with a syzbot report. syzkaller was injecting
IPv6 TCP SYN packets having a v4mapped source address.
After an unsuccessful 4-tuple lookup, TCP creates a request
socket (SYN_RECV) and calls reqsk_queue_hash_req()
reqsk_queue_hash_req() calls sk_ehashfn(sk)
At this point we have AF_INET6 sockets, and the heuristic
used by sk_ehashfn() to either hash the IPv4 or IPv6 addresses
is to use ipv6_addr_v4mapped(&sk->sk_v6_daddr)
For the particular spoofed packet, we end up hashing V4 addresses
which were not initialized by the TCP IPv6 stack, so KMSAN fired
a warning.
I first fixed sk_ehashfn() to test both source and destination addresses,
but then faced various problems, including user-space programs
like packetdrill that had similar assumptions.
Instead of trying to fix the whole ecosystem, it is better
to admit that we have a dual stack behavior, and that we
can not build linux kernels without V4 stack anyway.
The dual stack API automatically forces the traffic to be IPv4
if v4mapped addresses are used at bind() or connect(), so it makes
no sense to allow IPv6 traffic to use the same v4mapped class.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Remove the skb_ext_del from nf_reset, and renames it to a more
fitting nf_reset_ct(). Patch from Florian Westphal.
2) Fix deadlock in nft_connlimit between packet path updates and
the garbage collector.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Rajendra reported a kernel panic when a link was taken down:
[ 6870.263084] BUG: unable to handle kernel NULL pointer dereference at 00000000000000a8
[ 6870.271856] IP: [<ffffffff8efc5764>] __ipv6_ifa_notify+0x154/0x290
<snip>
[ 6870.570501] Call Trace:
[ 6870.573238] [<ffffffff8efc58c6>] ? ipv6_ifa_notify+0x26/0x40
[ 6870.579665] [<ffffffff8efc98ec>] ? addrconf_dad_completed+0x4c/0x2c0
[ 6870.586869] [<ffffffff8efe70c6>] ? ipv6_dev_mc_inc+0x196/0x260
[ 6870.593491] [<ffffffff8efc9c6a>] ? addrconf_dad_work+0x10a/0x430
[ 6870.600305] [<ffffffff8f01ade4>] ? __switch_to_asm+0x34/0x70
[ 6870.606732] [<ffffffff8ea93a7a>] ? process_one_work+0x18a/0x430
[ 6870.613449] [<ffffffff8ea93d6d>] ? worker_thread+0x4d/0x490
[ 6870.619778] [<ffffffff8ea93d20>] ? process_one_work+0x430/0x430
[ 6870.626495] [<ffffffff8ea99dd9>] ? kthread+0xd9/0xf0
[ 6870.632145] [<ffffffff8f01ade4>] ? __switch_to_asm+0x34/0x70
[ 6870.638573] [<ffffffff8ea99d00>] ? kthread_park+0x60/0x60
[ 6870.644707] [<ffffffff8f01ae77>] ? ret_from_fork+0x57/0x70
[ 6870.650936] Code: 31 c0 31 d2 41 b9 20 00 08 02 b9 09 00 00 0
addrconf_dad_work is kicked to be scheduled when a device is brought
up. There is a race between addrcond_dad_work getting scheduled and
taking the rtnl lock and a process taking the link down (under rtnl).
The latter removes the host route from the inet6_addr as part of
addrconf_ifdown which is run for NETDEV_DOWN. The former attempts
to use the host route in ipv6_ifa_notify. If the down event removes
the host route due to the race to the rtnl, then the BUG listed above
occurs.
This scenario does not occur when the ipv6 address is not kept
(net.ipv6.conf.all.keep_addr_on_down = 0) as addrconf_ifdown sets the
state of the ifp to DEAD. Handle when the addresses are kept by checking
IF_READY which is reset by addrconf_ifdown.
The 'dead' flag for an inet6_addr is set only under rtnl, in
addrconf_ifdown and it means the device is getting removed (or IPv6 is
disabled). The interesting cases for changing the idev flag are
addrconf_notify (NETDEV_UP and NETDEV_CHANGE) and addrconf_ifdown
(reset the flag). The former does not have the idev lock - only rtnl;
the latter has both. Based on that the existing dead + IF_READY check
can be moved to right after the rtnl_lock in addrconf_dad_work.
Fixes: f1705ec197 ("net: ipv6: Make address flushing on ifdown optional")
Reported-by: Rajendra Dendukuri <rajendra.dendukuri@broadcom.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just put related code together to ease code reading: the memcpy() is
related to the nla_reserve().
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 174e23810c
("sk_buff: drop all skb extensions on free and skb scrubbing") made napi
recycle always drop skb extensions. The additional skb_ext_del() that is
performed via nf_reset on napi skb recycle is not needed anymore.
Most nf_reset() calls in the stack are there so queued skb won't block
'rmmod nf_conntrack' indefinitely.
This removes the skb_ext_del from nf_reset, and renames it to a more
fitting nf_reset_ct().
In a few selected places, add a call to skb_ext_reset to make sure that
no active extensions remain.
I am submitting this for "net", because we're still early in the release
cycle. The patch applies to net-next too, but I think the rename causes
needless divergence between those trees.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
ctl packets sent on behalf of TIME_WAIT sockets currently
have a zero skb->priority, which can cause various problems.
In this patch we :
- add a tw_priority field in struct inet_timewait_sock.
- populate it from sk->sk_priority when a TIME_WAIT is created.
- For IPv4, change ip_send_unicast_reply() and its two
callers to propagate tw_priority correctly.
ip_send_unicast_reply() no longer changes sk->sk_priority.
- For IPv6, make sure TIME_WAIT sockets pass their tw_priority
field to tcp_v6_send_response() and tcp_v6_send_ack().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can populate skb->priority for some ctl packets
instead of always using zero.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, ip6_xmit() sets skb->priority based on sk->sk_priority
This is not desirable for TCP since TCP shares the same ctl socket
for a given netns. We want to be able to send RST or ACK packets
with a non zero skb->priority.
This patch has no functional change.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7d9e5f4221 removed references from certain dsts, but accounting
for this never translated down into the fib6 suppression code. This bug
was triggered by WireGuard users who use wg-quick(8), which uses the
"suppress-prefix" directive to ip-rule(8) for routing all of their
internet traffic without routing loops. The test case added here
causes the reference underflow by causing packets to evaluate a suppress
rule.
Fixes: 7d9e5f4221 ("ipv6: convert major tx path to use RT6_LOOKUP_F_DST_NOREF")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Acked-by: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yi Ren reported an issue discovered by syzkaller, and bisected
to the cited commit.
Many thanks to Yi, this trivial patch does not reflect the patient
work that has been done.
Fixes: d64a1f574a ("ipv6: honor RT6_LOOKUP_F_DST_NOREF in rule lookup logic")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Wei Wang <weiwan@google.com>
Bisected-and-reported-by: Yi Ren <c4tren@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
In ip6erspan_tunnel_xmit(), if the skb will not be sent out, it has to
be freed on the tx_err path. Otherwise when deleting a netns, it would
cause dst/dev to leak, and dmesg shows:
unregister_netdevice: waiting for lo to become free. Usage count = 1
Fixes: ef7baf5e08 ("ip6_gre: add ip6 erspan collect_md mode")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
UDP reuseport groups can hold a mix unconnected and connected sockets.
Ensure that connections only receive all traffic to their 4-tuple.
Fast reuseport returns on the first reuseport match on the assumption
that all matches are equal. Only if connections are present, return to
the previous behavior of scoring all sockets.
Record if connections are present and if so (1) treat such connected
sockets as an independent match from the group, (2) only return
2-tuple matches from reuseport and (3) do not return on the first
2-tuple reuseport match to allow for a higher scoring match later.
New field has_conns is set without locks. No other fields in the
bitmap are modified at runtime and the field is only ever set
unconditionally, so an RMW cannot miss a change.
Fixes: e32ea7e747 ("soreuseport: fast reuseport UDP socket selection")
Link: http://lkml.kernel.org/r/CA+FuTSfRP09aJNYRt04SS6qj22ViiOEWaWmLAwX0psk8-PGNxw@mail.gmail.com
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Craig Gallek <kraig@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable setting skb->mark for UDP and RAW sockets using cmsg.
This is analogous to existing support for TOS, TTL, txtime, etc.
Packet sockets already support this as of commit c7d39e3263
("packet: support per-packet fwmark for af_packet sendmsg").
Similar to other fields, implement by
1. initialize the sockcm_cookie.mark from socket option sk_mark
2. optionally overwrite this in ip_cmsg_send/ip6_datagram_send_ctl
3. initialize inet_cork.mark from sockcm_cookie.mark
4. initialize each (usually just one) skb->mark from inet_cork.mark
Step 1 is handled in one location for most protocols by ipcm_init_sk
as of commit 351782067b ("ipv4: ipcm_cookie initializers").
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next:
1) Fix error path of nf_tables_updobj(), from Dan Carpenter.
2) Move large structure away from stack in the nf_tables offload
infrastructure, from Arnd Bergmann.
3) Move indirect flow_block logic to nf_tables_offload.
4) Support for synproxy objects, from Fernando Fernandez Mancera.
5) Support for fwd and dup offload.
6) Add __nft_offload_get_chain() helper, this implicitly fixes missing
mutex and check for offload flags in the indirect block support,
patch from wenxu.
7) Remove rules on device unregistration, from wenxu. This includes
two preparation patches to reuse nft_flow_offload_chain() and
nft_flow_offload_rule().
Large batch from Jeremy Sowden to make a second pass to the
CONFIG_HEADER_TEST support and a bit of housekeeping:
8) Missing include guard in conntrack label header, from Jeremy Sowden.
9) A few coding style errors: trailing whitespace, incorrect indent in
Kconfig, and semicolons at the end of function definitions.
10) Remove unused ipt_init() and ip6t_init() declarations.
11) Inline xt_hashlimit, ebt_802_3 and xt_physdev headers. They are
only used once.
12) Update include directive in several netfilter files.
13) Remove unused include/net/netfilter/ipv6/nf_conntrack_icmpv6.h.
14) Move nf_ip6_ext_hdr() to include/linux/netfilter_ipv6.h
15) Move several synproxy structure definitions to nf_synproxy.h
16) Move nf_bridge_frag_data structure to include/linux/netfilter_bridge.h
17) Clean up static inline definitions in nf_conntrack_ecache.h.
18) Replace defined(CONFIG...) || defined(CONFIG...MODULE) with IS_ENABLED(CONFIG...).
19) Missing inline function conditional definitions based on Kconfig
preferences in synproxy and nf_conntrack_timeout.
20) Update br_nf_pre_routing_ipv6() definition.
21) Move conntrack code in linux/skbuff.h to nf_conntrack headers.
22) Several patches to remove superfluous CONFIG_NETFILTER and
CONFIG_NF_CONNTRACK checks in headers, coming from the initial batch
support for CONFIG_HEADER_TEST for netfilter.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a struct definition function in nf_conntrack_bridge.h which is
not specific to conntrack and is used elswhere in netfilter. Move it
into netfilter_bridge.h.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
There is an inline function in ip6_tables.h which is not specific to
ip6tables and is used elswhere in netfilter. Move it into
netfilter_ipv6.h and update the callers.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Include some headers in files which require them, and remove others
which are not required.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The '.exit' functions from 'pernet_operations' structure should be marked
as __net_exit, not __net_init.
Fixes: d862e54614 ("net: ipv6: Implement /proc/net/icmp6.")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the equivalent of commit 2c6b55f45d ("ipv6: fix neighbour
resolution with raw socket") for ip6_confirm_neigh(): we can send a
packet with MSG_CONFIRM on a raw socket for a connected route, so the
gateway would be :: here, and we should pick the next hop using
rt6_nexthop() instead.
This was found by code review and, to the best of my knowledge, doesn't
actually fix a practical issue: the destination address from the packet
is not considered while confirming a neighbour, as ip6_confirm_neigh()
calls choose_neigh_daddr() without passing the packet, so there are no
similar issues as the one fixed by said commit.
A possible source of issues with the existing implementation might come
from the fact that, if we have a cached dst, we won't consider it,
while rt6_nexthop() takes care of that. I might just not be creative
enough to find a practical problem here: the only way to affect this
with cached routes is to have one coming from an ICMPv6 redirect, but
if the next hop is a directly connected host, there should be no
topology for which a redirect applies here, and tests with redirected
routes show no differences for MSG_CONFIRM (and MSG_PROBE) packets on
raw sockets destined to a directly connected host.
However, directly using the dst gateway here is not consistent anymore
with neighbour resolution, and, in general, as we want the next hop,
using rt6_nexthop() looks like the only sane way to fetch it.
Reported-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Acked-by: Guillaume Nault <gnault@redhat.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a re-post of previous patch wrote by David Miller[1].
Phil Karn reported[2] that on busy networks with lots of unresolved
multicast routing entries, the creation of new multicast group routes
can be extremely slow and unreliable.
The reason is we hard-coded multicast route entries with unresolved source
addresses(cache_resolve_queue_len) to 10. If some multicast route never
resolves and the unresolved source addresses increased, there will
be no ability to create new multicast route cache.
To resolve this issue, we need either add a sysctl entry to make the
cache_resolve_queue_len configurable, or just remove cache_resolve_queue_len
limit directly, as we already have the socket receive queue limits of mrouted
socket, pointed by David.
>From my side, I'd perfer to remove the cache_resolve_queue_len limit instead
of creating two more(IPv4 and IPv6 version) sysctl entry.
[1] https://lkml.org/lkml/2018/7/22/11
[2] https://lkml.org/lkml/2018/7/21/343
v3: instead of remove cache_resolve_queue_len totally, let's only remove
the hard code limit when allocate the unresolved cache, as Eric Dumazet
suggested, so we don't need to re-count it in other places.
v2: hold the mfc_unres_lock while walking the unresolved list in
queue_count(), as Nikolay Aleksandrov remind.
Reported-by: Phil Karn <karn@ka9q.net>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes a stupid bug I recently introduced...
ip6_route_info_create() returns an ERR_PTR(err) and not a NULL on error.
Fixes: d55a2e374a ("net-ipv6: fix excessive RTF_ADDRCONF flag on ::1/128 local route (and others)'")
Cc: David Ahern <dsahern@gmail.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When creating a v4 route that uses a v6 nexthop from a nexthop group.
Allow the kernel to properly send the nexthop as v6 via the RTA_VIA
attribute.
Broken behavior:
$ ip nexthop add via fe80::9 dev eth0
$ ip nexthop show
id 1 via fe80::9 dev eth0 scope link
$ ip route add 4.5.6.7/32 nhid 1
$ ip route show
default via 10.0.2.2 dev eth0
4.5.6.7 nhid 1 via 254.128.0.0 dev eth0
10.0.2.0/24 dev eth0 proto kernel scope link src 10.0.2.15
$
Fixed behavior:
$ ip nexthop add via fe80::9 dev eth0
$ ip nexthop show
id 1 via fe80::9 dev eth0 scope link
$ ip route add 4.5.6.7/32 nhid 1
$ ip route show
default via 10.0.2.2 dev eth0
4.5.6.7 nhid 1 via inet6 fe80::9 dev eth0
10.0.2.0/24 dev eth0 proto kernel scope link src 10.0.2.15
$
v2, v3: Addresses code review comments from David Ahern
Fixes: dcb1ecb50e (“ipv4: Prepare for fib6_nh from a nexthop object”)
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A change to the core nla helpers was missed during the push of
the nexthop changes. rt6_fill_node_nexthop should be calling
nla_nest_start_noflag not nla_nest_start. Currently, iproute2
does not print multipath data because of parsing issues with
the attribute.
Fixes: f88d8ea67f ("ipv6: Plumb support for nexthop object in a fib6_info")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a subtle change in behaviour introduced by:
commit c7a1ce397a
'ipv6: Change addrconf_f6i_alloc to use ip6_route_info_create'
Before that patch /proc/net/ipv6_route includes:
00000000000000000000000000000001 80 00000000000000000000000000000000 00 00000000000000000000000000000000 00000000 00000003 00000000 80200001 lo
Afterwards /proc/net/ipv6_route includes:
00000000000000000000000000000001 80 00000000000000000000000000000000 00 00000000000000000000000000000000 00000000 00000002 00000000 80240001 lo
ie. the above commit causes the ::1/128 local (automatic) route to be flagged with RTF_ADDRCONF (0x040000).
AFAICT, this is incorrect since these routes are *not* coming from RA's.
As such, this patch restores the old behaviour.
Fixes: c7a1ce397a ("ipv6: Change addrconf_f6i_alloc to use ip6_route_info_create")
Cc: David Ahern <dsahern@gmail.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, ipv6_find_idev returns NULL when ipv6_add_dev fails,
ignoring the specific error value. This results in addrconf_add_dev
returning ENOBUFS in all cases, which is unfortunate in cases such as:
# ip link add dummyX type dummy
# ip link set dummyX mtu 1200 up
# ip addr add 2000::/64 dev dummyX
RTNETLINK answers: No buffer space available
Commit a317a2f19d ("ipv6: fail early when creating netdev named all
or default") introduced error returns in ipv6_add_dev. Before that,
that function would simply return NULL for all failures.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 93a714d6b5 ("multicast: Extend ip address command to enable
multicast group join/leave on") we added a new flag IFA_F_MCAUTOJOIN
to make user able to add multicast address on ethernet interface.
This works for IPv4, but not for IPv6. See the inet6_addr_add code.
static int inet6_addr_add()
{
...
if (cfg->ifa_flags & IFA_F_MCAUTOJOIN) {
ipv6_mc_config(net->ipv6.mc_autojoin_sk, true...)
}
ifp = ipv6_add_addr(idev, cfg, true, extack); <- always fail with maddr
if (!IS_ERR(ifp)) {
...
} else if (cfg->ifa_flags & IFA_F_MCAUTOJOIN) {
ipv6_mc_config(net->ipv6.mc_autojoin_sk, false...)
}
}
But in ipv6_add_addr() it will check the address type and reject multicast
address directly. So this feature is never worked for IPv6.
We should not remove the multicast address check totally in ipv6_add_addr(),
but could accept multicast address only when IFA_F_MCAUTOJOIN flag supplied.
v2: update commit description
Fixes: 93a714d6b5 ("multicast: Extend ip address command to enable multicast group join/leave on")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for net-next:
1) Rename mss field to mss_option field in synproxy, from Fernando Mancera.
2) Use SYSCTL_{ZERO,ONE} definitions in conntrack, from Matteo Croce.
3) More strict validation of IPVS sysctl values, from Junwei Hu.
4) Remove unnecessary spaces after on the right hand side of assignments,
from yangxingwu.
5) Add offload support for bitwise operation.
6) Extend the nft_offload_reg structure to store immediate date.
7) Collapse several ip_set header files into ip_set.h, from
Jeremy Sowden.
8) Make netfilter headers compile with CONFIG_KERNEL_HEADER_TEST=y,
from Jeremy Sowden.
9) Fix several sparse warnings due to missing prototypes, from
Valdis Kletnieks.
10) Use static lock initialiser to ensure connlabel spinlock is
initialized on boot time to fix sched/act_ct.c, patch
from Florian Westphal.
====================
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Daniel Borkmann says:
====================
The following pull-request contains BPF updates for your *net-next* tree.
There is a small merge conflict in libbpf (Cc Andrii so he's in the loop
as well):
for (i = 1; i <= btf__get_nr_types(btf); i++) {
t = (struct btf_type *)btf__type_by_id(btf, i);
if (!has_datasec && btf_is_var(t)) {
/* replace VAR with INT */
t->info = BTF_INFO_ENC(BTF_KIND_INT, 0, 0);
<<<<<<< HEAD
/*
* using size = 1 is the safest choice, 4 will be too
* big and cause kernel BTF validation failure if
* original variable took less than 4 bytes
*/
t->size = 1;
*(int *)(t+1) = BTF_INT_ENC(0, 0, 8);
} else if (!has_datasec && kind == BTF_KIND_DATASEC) {
=======
t->size = sizeof(int);
*(int *)(t + 1) = BTF_INT_ENC(0, 0, 32);
} else if (!has_datasec && btf_is_datasec(t)) {
>>>>>>> 72ef80b5ee
/* replace DATASEC with STRUCT */
Conflict is between the two commits 1d4126c4e1 ("libbpf: sanitize VAR to
conservative 1-byte INT") and b03bc6853c ("libbpf: convert libbpf code to
use new btf helpers"), so we need to pick the sanitation fixup as well as
use the new btf_is_datasec() helper and the whitespace cleanup. Looks like
the following:
[...]
if (!has_datasec && btf_is_var(t)) {
/* replace VAR with INT */
t->info = BTF_INFO_ENC(BTF_KIND_INT, 0, 0);
/*
* using size = 1 is the safest choice, 4 will be too
* big and cause kernel BTF validation failure if
* original variable took less than 4 bytes
*/
t->size = 1;
*(int *)(t + 1) = BTF_INT_ENC(0, 0, 8);
} else if (!has_datasec && btf_is_datasec(t)) {
/* replace DATASEC with STRUCT */
[...]
The main changes are:
1) Addition of core parts of compile once - run everywhere (co-re) effort,
that is, relocation of fields offsets in libbpf as well as exposure of
kernel's own BTF via sysfs and loading through libbpf, from Andrii.
More info on co-re: http://vger.kernel.org/bpfconf2019.html#session-2
and http://vger.kernel.org/lpc-bpf2018.html#session-2
2) Enable passing input flags to the BPF flow dissector to customize parsing
and allowing it to stop early similar to the C based one, from Stanislav.
3) Add a BPF helper function that allows generating SYN cookies from XDP and
tc BPF, from Petar.
4) Add devmap hash-based map type for more flexibility in device lookup for
redirects, from Toke.
5) Improvements to XDP forwarding sample code now utilizing recently enabled
devmap lookups, from Jesper.
6) Add support for reporting the effective cgroup progs in bpftool, from Jakub
and Takshak.
7) Fix reading kernel config from bpftool via /proc/config.gz, from Peter.
8) Fix AF_XDP umem pages mapping for 32 bit architectures, from Ivan.
9) Follow-up to add two more BPF loop tests for the selftest suite, from Alexei.
10) Add perf event output helper also for other skb-based program types, from Allan.
11) Fix a co-re related compilation error in selftests, from Yonghong.
====================
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Before commit d4289fcc9b ("net: IP6 defrag: use rbtrees for IPv6
defrag"), a netperf UDP_STREAM test[0] using big IPv6 datagrams (thus
generating many fragments) and running over an IPsec tunnel, reported
more than 6Gbps throughput. After that patch, the same test gets only
9Mbps when receiving on a be2net nic (driver can make a big difference
here, for example, ixgbe doesn't seem to be affected).
By reusing the IPv4 defragmentation code, IPv6 lost fragment coalescing
(IPv4 fragment coalescing was dropped by commit 14fe22e334 ("Revert
"ipv4: use skb coalescing in defragmentation"")).
Without fragment coalescing, be2net runs out of Rx ring entries and
starts to drop frames (ethtool reports rx_drops_no_frags errors). Since
the netperf traffic is only composed of UDP fragments, any lost packet
prevents reassembly of the full datagram. Therefore, fragments which
have no possibility to ever get reassembled pile up in the reassembly
queue, until the memory accounting exeeds the threshold. At that point
no fragment is accepted anymore, which effectively discards all
netperf traffic.
When reassembly timeout expires, some stale fragments are removed from
the reassembly queue, so a few packets can be received, reassembled
and delivered to the netperf receiver. But the nic still drops frames
and soon the reassembly queue gets filled again with stale fragments.
These long time frames where no datagram can be received explain why
the performance drop is so significant.
Re-introducing fragment coalescing is enough to get the initial
performances again (6.6Gbps with be2net): driver doesn't drop frames
anymore (no more rx_drops_no_frags errors) and the reassembly engine
works at full speed.
This patch is quite conservative and only coalesces skbs for local
IPv4 and IPv6 delivery (in order to avoid changing skb geometry when
forwarding). Coalescing could be extended in the future if need be, as
more scenarios would probably benefit from it.
[0]: Test configuration
Sender:
ip xfrm policy flush
ip xfrm state flush
ip xfrm state add src fc00:1::1 dst fc00:2::1 proto esp spi 0x1000 aead 'rfc4106(gcm(aes))' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b 96 mode transport sel src fc00:1::1 dst fc00:2::1
ip xfrm policy add src fc00:1::1 dst fc00:2::1 dir in tmpl src fc00:1::1 dst fc00:2::1 proto esp mode transport action allow
ip xfrm state add src fc00:2::1 dst fc00:1::1 proto esp spi 0x1001 aead 'rfc4106(gcm(aes))' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b 96 mode transport sel src fc00:2::1 dst fc00:1::1
ip xfrm policy add src fc00:2::1 dst fc00:1::1 dir out tmpl src fc00:2::1 dst fc00:1::1 proto esp mode transport action allow
netserver -D -L fc00:2::1
Receiver:
ip xfrm policy flush
ip xfrm state flush
ip xfrm state add src fc00:2::1 dst fc00:1::1 proto esp spi 0x1001 aead 'rfc4106(gcm(aes))' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b 96 mode transport sel src fc00:2::1 dst fc00:1::1
ip xfrm policy add src fc00:2::1 dst fc00:1::1 dir in tmpl src fc00:2::1 dst fc00:1::1 proto esp mode transport action allow
ip xfrm state add src fc00:1::1 dst fc00:2::1 proto esp spi 0x1000 aead 'rfc4106(gcm(aes))' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b 96 mode transport sel src fc00:1::1 dst fc00:2::1
ip xfrm policy add src fc00:1::1 dst fc00:2::1 dir out tmpl src fc00:1::1 dst fc00:2::1 proto esp mode transport action allow
netperf -H fc00:2::1 -f k -P 0 -L fc00:1::1 -l 60 -t UDP_STREAM -I 99,5 -i 5,5 -T5,5 -6
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the unlock path in __ip6_rt_update_pmtu by using a
single point where rcu_read_unlock is called.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nexthop path in rt6_update_exception_stamp_rt needs to call
rcu_read_unlock if it fails to find a fib6_nh match rather than
just returning.
Fixes: e659ba31d8 ("ipv6: Handle all fib6_nh in a nexthop in exception handling")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After introduce "mss_encode" field in the synproxy_options struct the field
"mss" is a little confusing. It has been renamed to "mss_option".
Signed-off-by: Fernando Fernandez Mancera <ffmancera@riseup.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch allows generation of a SYN cookie before an SKB has been
allocated, as is the case at XDP.
Signed-off-by: Petar Penkov <ppenkov@google.com>
Reviewed-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
ipv6_find_hdr() prints a non-rate limited error message
when it cannot find an ipv6 header at a specific offset.
This could be used as a DoS, so just remove it.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip4ip6/ip6ip6 tunnels run iptunnel_handle_offloads on xmit which
can cause a possible use-after-free accessing iph/ipv6h pointer
since the packet will be 'uncloned' running pskb_expand_head if
it is a cloned gso skb.
Fixes: 0e9a709560 ("ip6_tunnel, ip6_gre: fix setting of DSCP on encapsulated packets")
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since ip6_tnl_parse_tlv_enc_lim() can call pskb_may_pull()
which may change skb->data, so we need to re-load ipv6h at
the right place.
Fixes: 898b29798e ("ip6_gre: Refactor ip6gre xmit codes")
Cc: William Tu <u9012063@gmail.com>
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Acked-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is trivial since we already have support for the entirely
identical (from the kernel's point of view) RDNSS and DNSSL that
also contain opaque data that needs to be passed down to userspace.
As specified in RFC7710, Captive Portal option contains a URL.
8-bit identifier of the option type as assigned by the IANA is 37.
This option should also be treated as userland.
Hence, treat ND option 37 as userland (Captive Portal support)
See:
https://tools.ietf.org/html/rfc7710https://www.iana.org/assignments/icmpv6-parameters/icmpv6-parameters.xhtml
Fixes: e35f30c131
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: Remin Nguyen Van <reminv@google.com>
Cc: Alexey I. Froloff <raorn@raorn.name>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Fix a deadlock when module is requested via netlink_bind()
in nfnetlink, from Florian Westphal.
2) Fix ipt_rpfilter and ip6t_rpfilter with VRF, from Miaohe Lin.
3) Skip master comparison in SIP helper to fix expectation clash
under two valid scenarios, from xiao ruizhu.
4) Remove obsolete comments in nf_conntrack codebase, from
Yonatan Goldschmidt.
5) Fix redirect extension module autoload, from Christian Hesse.
6) Fix incorrect mssg option sent to client in synproxy,
from Fernando Fernandez.
7) Fix incorrect window calculations in TCP conntrack, from
Florian Westphal.
8) Don't bail out when updating basechain policy due to recent
offload works, also from Florian.
9) Allow symhash to use modulus 1 as other hash extensions do,
from Laura.Garcia.
10) Missing NAT chain module autoload for the inet family,
from Phil Sutter.
11) Fix missing adjustment of TCP RST packet in synproxy,
from Fernando Fernandez.
12) Skip EAGAIN path when nft_meta_bridge is built-in or
not selected.
13) Conntrack bridge does not depend on nf_tables_bridge.
14) Turn NF_TABLES_BRIDGE into tristate to fix possible
link break of nft_meta_bridge, from Arnd Bergmann.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix AF_XDP cq entry leak, from Ilya Maximets.
2) Fix handling of PHY power-down on RTL8411B, from Heiner Kallweit.
3) Add some new PCI IDs to iwlwifi, from Ihab Zhaika.
4) Fix handling of neigh timers wrt. entries added by userspace, from
Lorenzo Bianconi.
5) Various cases of missing of_node_put(), from Nishka Dasgupta.
6) The new NET_ACT_CT needs to depend upon NF_NAT, from Yue Haibing.
7) Various RDS layer fixes, from Gerd Rausch.
8) Fix some more fallout from TCQ_F_CAN_BYPASS generalization, from
Cong Wang.
9) Fix FIB source validation checks over loopback, also from Cong Wang.
10) Use promisc for unsupported number of filters, from Justin Chen.
11) Missing sibling route unlink on failure in ipv6, from Ido Schimmel.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (90 commits)
tcp: fix tcp_set_congestion_control() use from bpf hook
ag71xx: fix return value check in ag71xx_probe()
ag71xx: fix error return code in ag71xx_probe()
usb: qmi_wwan: add D-Link DWM-222 A2 device ID
bnxt_en: Fix VNIC accounting when enabling aRFS on 57500 chips.
net: dsa: sja1105: Fix missing unlock on error in sk_buff()
gve: replace kfree with kvfree
selftests/bpf: fix test_xdp_noinline on s390
selftests/bpf: fix "valid read map access into a read-only array 1" on s390
net/mlx5: Replace kfree with kvfree
MAINTAINERS: update netsec driver
ipv6: Unlink sibling route in case of failure
liquidio: Replace vmalloc + memset with vzalloc
udp: Fix typo in net/ipv4/udp.c
net: bcmgenet: use promisc for unsupported filters
ipv6: rt6_check should return NULL if 'from' is NULL
tipc: initialize 'validated' field of received packets
selftests: add a test case for rp_filter
fib: relax source validation check for loopback packets
mlxsw: spectrum: Do not process learned records with a dummy FID
...
In the sysctl code the proc_dointvec_minmax() function is often used to
validate the user supplied value between an allowed range. This
function uses the extra1 and extra2 members from struct ctl_table as
minimum and maximum allowed value.
On sysctl handler declaration, in every source file there are some
readonly variables containing just an integer which address is assigned
to the extra1 and extra2 members, so the sysctl range is enforced.
The special values 0, 1 and INT_MAX are very often used as range
boundary, leading duplication of variables like zero=0, one=1,
int_max=INT_MAX in different source files:
$ git grep -E '\.extra[12].*&(zero|one|int_max)' |wc -l
248
Add a const int array containing the most commonly used values, some
macros to refer more easily to the correct array member, and use them
instead of creating a local one for every object file.
This is the bloat-o-meter output comparing the old and new binary
compiled with the default Fedora config:
# scripts/bloat-o-meter -d vmlinux.o.old vmlinux.o
add/remove: 2/2 grow/shrink: 0/2 up/down: 24/-188 (-164)
Data old new delta
sysctl_vals - 12 +12
__kstrtab_sysctl_vals - 12 +12
max 14 10 -4
int_max 16 - -16
one 68 - -68
zero 128 28 -100
Total: Before=20583249, After=20583085, chg -0.00%
[mcroce@redhat.com: tipc: remove two unused variables]
Link: http://lkml.kernel.org/r/20190530091952.4108-1-mcroce@redhat.com
[akpm@linux-foundation.org: fix net/ipv6/sysctl_net_ipv6.c]
[arnd@arndb.de: proc/sysctl: make firmware loader table conditional]
Link: http://lkml.kernel.org/r/20190617130014.1713870-1-arnd@arndb.de
[akpm@linux-foundation.org: fix fs/eventpoll.c]
Link: http://lkml.kernel.org/r/20190430180111.10688-1-mcroce@redhat.com
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Aaron Tomlin <atomlin@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a route needs to be appended to an existing multipath route,
fib6_add_rt2node() first appends it to the siblings list and increments
the number of sibling routes on each sibling.
Later, the function notifies the route via call_fib6_entry_notifiers().
In case the notification is vetoed, the route is not unlinked from the
siblings list, which can result in a use-after-free.
Fix this by unlinking the route from the siblings list before returning
an error.
Audited the rest of the call sites from which the FIB notification chain
is called and could not find more problems.
Fixes: 2233000cba ("net/ipv6: Move call_fib6_entry_notifiers up for route adds")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alexander Petrovskiy <alexpe@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul reported that l2tp sessions were broken after the commit referenced
in the Fixes tag. Prior to this commit rt6_check returned NULL if the
rt6_info 'from' was NULL - ie., the dst_entry was disconnected from a FIB
entry. Restore that behavior.
Fixes: 93531c6743 ("net/ipv6: separate handling of FIB entries from dst based routes")
Reported-by: Paul Donohue <linux-kernel@PaulSD.com>
Tested-by: Paul Donohue <linux-kernel@PaulSD.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now synproxy sends the mss value set by the user on client syn-ack packet
instead of the mss value that client announced.
Fixes: 48b1de4c11 ("netfilter: add SYNPROXY core/target")
Signed-off-by: Fernando Fernandez Mancera <ffmancera@riseup.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When firewalld is enabled with ipv4/ipv6 rpfilter, vrf
ipv4/ipv6 packets will be dropped. Vrf device will pass
through netfilter hook twice. One with enslaved device
and another one with l3 master device. So in device may
dismatch witch out device because out device is always
enslaved device.So failed with the check of the rpfilter
and drop the packets by mistake.
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Same as other ip tunnel, use dst_cache in xmit action to avoid
unnecessary fib lookups.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 323a53c412 ("ipv6: tcp: enable flowlabel reflection in some RST packets")
and 50a8accf10 ("ipv6: tcp: send consistent flowlabel in TIME_WAIT state")
we took care of IPv6 flowlabel reflections for two cases.
This patch takes care of the remaining case, when the RST packet
is sent on behalf of a 'full' socket.
In Marek use case, this was a socket in TCP_CLOSE state.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Marek Majkowski <marek@cloudflare.com>
Tested-by: Marek Majkowski <marek@cloudflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The length of AH header is computed manually as (hp->hdrlen+2)<<2.
However, in include/linux/ipv6.h, a macro named ipv6_authlen is
already defined for exactly the same job. This commit replaces
the manual computation code with the macro.
Signed-off-by: yangxingwu <xingwu.yang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"Some highlights from this development cycle:
1) Big refactoring of ipv6 route and neigh handling to support
nexthop objects configurable as units from userspace. From David
Ahern.
2) Convert explored_states in BPF verifier into a hash table,
significantly decreased state held for programs with bpf2bpf
calls, from Alexei Starovoitov.
3) Implement bpf_send_signal() helper, from Yonghong Song.
4) Various classifier enhancements to mvpp2 driver, from Maxime
Chevallier.
5) Add aRFS support to hns3 driver, from Jian Shen.
6) Fix use after free in inet frags by allocating fqdirs dynamically
and reworking how rhashtable dismantle occurs, from Eric Dumazet.
7) Add act_ctinfo packet classifier action, from Kevin
Darbyshire-Bryant.
8) Add TFO key backup infrastructure, from Jason Baron.
9) Remove several old and unused ISDN drivers, from Arnd Bergmann.
10) Add devlink notifications for flash update status to mlxsw driver,
from Jiri Pirko.
11) Lots of kTLS offload infrastructure fixes, from Jakub Kicinski.
12) Add support for mv88e6250 DSA chips, from Rasmus Villemoes.
13) Various enhancements to ipv6 flow label handling, from Eric
Dumazet and Willem de Bruijn.
14) Support TLS offload in nfp driver, from Jakub Kicinski, Dirk van
der Merwe, and others.
15) Various improvements to axienet driver including converting it to
phylink, from Robert Hancock.
16) Add PTP support to sja1105 DSA driver, from Vladimir Oltean.
17) Add mqprio qdisc offload support to dpaa2-eth, from Ioana
Radulescu.
18) Add devlink health reporting to mlx5, from Moshe Shemesh.
19) Convert stmmac over to phylink, from Jose Abreu.
20) Add PTP PHC (Physical Hardware Clock) support to mlxsw, from
Shalom Toledo.
21) Add nftables SYNPROXY support, from Fernando Fernandez Mancera.
22) Convert tcp_fastopen over to use SipHash, from Ard Biesheuvel.
23) Track spill/fill of constants in BPF verifier, from Alexei
Starovoitov.
24) Support bounded loops in BPF, from Alexei Starovoitov.
25) Various page_pool API fixes and improvements, from Jesper Dangaard
Brouer.
26) Just like ipv4, support ref-countless ipv6 route handling. From
Wei Wang.
27) Support VLAN offloading in aquantia driver, from Igor Russkikh.
28) Add AF_XDP zero-copy support to mlx5, from Maxim Mikityanskiy.
29) Add flower GRE encap/decap support to nfp driver, from Pieter
Jansen van Vuuren.
30) Protect against stack overflow when using act_mirred, from John
Hurley.
31) Allow devmap map lookups from eBPF, from Toke Høiland-Jørgensen.
32) Use page_pool API in netsec driver, Ilias Apalodimas.
33) Add Google gve network driver, from Catherine Sullivan.
34) More indirect call avoidance, from Paolo Abeni.
35) Add kTLS TX HW offload support to mlx5, from Tariq Toukan.
36) Add XDP_REDIRECT support to bnxt_en, from Andy Gospodarek.
37) Add MPLS manipulation actions to TC, from John Hurley.
38) Add sending a packet to connection tracking from TC actions, and
then allow flower classifier matching on conntrack state. From
Paul Blakey.
39) Netfilter hw offload support, from Pablo Neira Ayuso"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2080 commits)
net/mlx5e: Return in default case statement in tx_post_resync_params
mlx5: Return -EINVAL when WARN_ON_ONCE triggers in mlx5e_tls_resync().
net: dsa: add support for BRIDGE_MROUTER attribute
pkt_sched: Include const.h
net: netsec: remove static declaration for netsec_set_tx_de()
net: netsec: remove superfluous if statement
netfilter: nf_tables: add hardware offload support
net: flow_offload: rename tc_cls_flower_offload to flow_cls_offload
net: flow_offload: add flow_block_cb_is_busy() and use it
net: sched: remove tcf block API
drivers: net: use flow block API
net: sched: use flow block API
net: flow_offload: add flow_block_cb_{priv, incref, decref}()
net: flow_offload: add list handling functions
net: flow_offload: add flow_block_cb_alloc() and flow_block_cb_free()
net: flow_offload: rename TCF_BLOCK_BINDER_TYPE_* to FLOW_BLOCK_BINDER_TYPE_*
net: flow_offload: rename TC_BLOCK_{UN}BIND to FLOW_BLOCK_{UN}BIND
net: flow_offload: add flow_block_cb_setup_simple()
net: hisilicon: Add an tx_desc to adapt HI13X1_GMAC
net: hisilicon: Add an rx_desc to adapt HI13X1_GMAC
...
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with other
trees, unfortunately. He has a lot more of these waiting on the wings
that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos, and one
on Spectre vulnerabilities.
- Various improvements to the build system, including automatic markup of
function() references because some people, for reasons I will never
understand, were of the opinion that :c:func:``function()`` is
unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAl0krAEPHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5Yg98H/AuLqO9LpOgUjF4LhyjxGPdzJkY9RExSJ7km
gznyreLCZgFaJR+AY6YDsd4Jw6OJlPbu1YM/Qo3C3WrZVFVhgL/s2ebvBgCo50A8
raAFd8jTf4/mGCHnAqRotAPQ3mETJUk315B66lBJ6Oc+YdpRhwXWq8ZW2bJxInFF
3HDvoFgMf0KhLuMHUkkL0u3fxH1iA+KvDu8diPbJYFjOdOWENz/CV8wqdVkXRSEW
DJxIq89h/7d+hIG3d1I7Nw+gibGsAdjSjKv4eRKauZs4Aoxd1Gpl62z0JNk6aT3m
dtq4joLdwScydonXROD/Twn2jsu4xYTrPwVzChomElMowW/ZBBY=
=D0eO
-----END PGP SIGNATURE-----
Merge tag 'docs-5.3' of git://git.lwn.net/linux
Pull Documentation updates from Jonathan Corbet:
"It's been a relatively busy cycle for docs:
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with
other trees, unfortunately. He has a lot more of these waiting on
the wings that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos,
and one on Spectre vulnerabilities.
- Various improvements to the build system, including automatic
markup of function() references because some people, for reasons I
will never understand, were of the opinion that
:c:func:``function()`` is unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc"
* tag 'docs-5.3' of git://git.lwn.net/linux: (129 commits)
docs: automarkup.py: ignore exceptions when seeking for xrefs
docs: Move binderfs to admin-guide
Disable Sphinx SmartyPants in HTML output
doc: RCU callback locks need only _bh, not necessarily _irq
docs: format kernel-parameters -- as code
Doc : doc-guide : Fix a typo
platform: x86: get rid of a non-existent document
Add the RCU docs to the core-api manual
Documentation: RCU: Add TOC tree hooks
Documentation: RCU: Rename txt files to rst
Documentation: RCU: Convert RCU UP systems to reST
Documentation: RCU: Convert RCU linked list to reST
Documentation: RCU: Convert RCU basic concepts to reST
docs: filesystems: Remove uneeded .rst extension on toctables
scripts/sphinx-pre-install: fix out-of-tree build
docs: zh_CN: submitting-drivers.rst: Remove a duplicated Documentation/
Documentation: PGP: update for newer HW devices
Documentation: Add section about CPU vulnerabilities for Spectre
Documentation: platform: Delete x86-laptop-drivers.txt
docs: Note that :c:func: should no longer be used
...
Processes can request ipv6 flowlabels with cmsg IPV6_FLOWINFO.
If not set, by default an autogenerated flowlabel is selected.
Explicit flowlabels require a control operation per label plus a
datapath check on every connection (every datagram if unconnected).
This is particularly expensive on unconnected sockets multiplexing
many flows, such as QUIC.
In the common case, where no lease is exclusive, the check can be
safely elided, as both lease request and check trivially succeed.
Indeed, autoflowlabel does the same even with exclusive leases.
Elide the check if no process has requested an exclusive lease.
fl6_sock_lookup previously returns either a reference to a lease or
NULL to denote failure. Modify to return a real error and update
all callers. On return NULL, they can use the label and will elide
the atomic_dec in fl6_sock_release.
This is an optimization. Robust applications still have to revert to
requesting leases if the fast path fails due to an exclusive lease.
Changes RFC->v1:
- use static_key_false_deferred to rate limit jump label operations
- call static_key_deferred_flush to stop timers on exit
- move decrement out of RCU context
- defer optimization also if opt data is associated with a lease
- updated all fp6_sock_lookup callers, not just udp
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the same support as commit 363887a2cd ("ipv4: Support multipath
hashing on inner IP pkts for GRE tunnel") for outer IPv6. The hashing
considers both IPv4 and IPv6 pkts when they are tunneled by IPv6 GRE.
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2019-07-05
1) A lot of work to remove indirections from the xfrm code.
From Florian Westphal.
2) Fix a WARN_ON with ipv6 that triggered because of a
forgotten break statement. From Florian Westphal.
3) Remove xfrmi_init_net, it is not needed.
From Li RongQing.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This avoids an indirect call per syscall for common ipv6 transports
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will simplify indirect call wrapper invocation in the following
patch.
No functional change intended, any - out-of-tree - IPv6 user of
inet_{recv,send}msg can keep using the existing functions.
SCTP code still uses the existing version even for ipv6: as this series
will not add ICW for SCTP, moving to the new helper would not give
any benefit.
The only other in-kernel user of inet_{recv,send}msg is
pvcalls_conn_back_read(), but psvcalls explicitly creates only IPv4 socket,
so no need to update that code path, too.
v1 -> v2: drop inet6_{recv,send}msg declaration from header file,
prefer ICW macro instead
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use blackhole_netdev instead of 'lo' device with lower MTU when marking
dst "dead".
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Tested-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
/proc/sys/net/ipv6/flowlabel_reflect assumes written value to be in the
range of 0 to 3. Use proc_dointvec_minmax instead of proc_dointvec.
Fixes: 323a53c412 ("ipv6: tcp: enable flowlabel reflection in some RST packets")
Signed-off-by: Eiichi Tsukata <devel@etsukata.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend flowlabel_reflect bitmask to allow conditional
reflection of incoming flowlabels in echo replies.
Note this has precedence against auto flowlabels.
Add flowlabel_reflect enum to replace hard coded
values.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
esp4_get_mtu and esp6_get_mtu are exactly the same, the only difference
is a single sizeof() (ipv4 vs. ipv6 header).
Merge both into xfrm_state_mtu() and remove the indirection.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
The new route handling in ip_mc_finish_output() from 'net' overlapped
with the new support for returning congestion notifications from BPF
programs.
In order to handle this I had to take the dev_loopback_xmit() calls
out of the switch statement.
The aquantia driver conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Gateway validation does not need a dst_entry, it only needs the fib
entry to validate the gateway resolution and egress device. So,
convert ip6_nh_lookup_table from ip6_pol_route to fib6_table_lookup
and ip6_route_check_nh to use fib6_lookup over rt6_lookup.
ip6_pol_route is a call to fib6_table_lookup and if successful a call
to fib6_select_path. From there the exception cache is searched for an
entry or a dst_entry is created to return to the caller. The exception
entry is not relevant for gateway validation, so what matters are the
calls to fib6_table_lookup and then fib6_select_path.
Similarly, rt6_lookup can be replaced with a call to fib6_lookup with
RT6_LOOKUP_F_IFACE set in flags. Again, the exception cache search is
not relevant, only the lookup with path selection. The primary difference
in the lookup paths is the use of rt6_select with fib6_lookup versus
rt6_device_match with rt6_lookup. When you remove complexities in the
rt6_select path, e.g.,
1. saddr is not set for gateway validation, so RT6_LOOKUP_F_HAS_SADDR
is not relevant
2. rt6_check_neigh is not called so that removes the RT6_NUD_FAIL_DO_RR
return and round-robin logic.
the code paths are believed to be equivalent for the given use case -
validate the gateway and optionally given the device. Furthermore, it
aligns the validation with onlink code path and the lookup path actually
used for rx and tx.
Adjust the users, ip6_route_check_nh_onlink and ip6_route_check_nh to
handle a fib6_info vs a rt6_info when performing validation checks.
Existing selftests fib-onlink-tests.sh and fib_tests.sh are used to
verify the changes.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The scenario is the following: the user uses a raw socket to send an ipv6
packet, destinated to a not-connected network, and specify a connected nh.
Here is the corresponding python script to reproduce this scenario:
import socket
IPPROTO_RAW = 255
send_s = socket.socket(socket.AF_INET6, socket.SOCK_RAW, IPPROTO_RAW)
# scapy
# p = IPv6(src='fd00💯:1', dst='fd00:200::fa')/ICMPv6EchoRequest()
# str(p)
req = b'`\x00\x00\x00\x00\x08:@\xfd\x00\x01\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x01\xfd\x00\x02\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\xfa\x80\x00\x81\xc0\x00\x00\x00\x00'
send_s.sendto(req, ('fd00:175::2', 0, 0, 0))
fd00:175::/64 is a connected route and fd00:200::fa is not a connected
host.
With this scenario, the kernel starts by sending a NS to resolve
fd00:175::2. When it receives the NA, it flushes its queue and try to send
the initial packet. But instead of sending it, it sends another NS to
resolve fd00:200::fa, which obvioulsy fails, thus the packet is dropped. If
the user sends again the packet, it now uses the right nh (fd00:175::2).
The problem is that ip6_dst_lookup_neigh() uses the rt6i_gateway, which is
:: because the associated route is a connected route, thus it uses the dst
addr of the packet. Let's use rt6_nexthop() to choose the right nh.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no functional change in this patch, it only prepares the next one.
rt6_nexthop() will be used by ip6_dst_lookup_neigh(), which uses const
variables.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reported-by: kbuild test robot <lkp@intel.com>
Acked-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
/proc/sys/net/ipv6/route/skip_notify_on_dev_down assumes given value to be
0 or 1. Use proc_dointvec_minmax instead of proc_dointvec.
Fixes: 7c6bb7d2fa ("net/ipv6: Add knob to skip DELROUTE message ondevice down")
Signed-off-by: Eiichi Tsukata <devel@etsukata.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resolve conflict between d2912cb15b ("treewide: Replace GPLv2
boilerplate/reference with SPDX - rule 500") removing the GPL disclaimer
and fe03d47456 ("Update my email address") which updates Jozsef
Kadlecsik's email.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When we perform an inexact match on FIB nodes via fib6_locate_1(), longer
prefixes will be preferred to shorter ones. However, it might happen that
a node, with higher fn_bit value than some other, has no valid routing
information.
In this case, we'll pick that node, but it will be discarded by the check
on RTN_RTINFO in fib6_locate(), and we might miss nodes with valid routing
information but with lower fn_bit value.
This is apparent when a routing exception is created for a default route:
# ip -6 route list
fc00:1::/64 dev veth_A-R1 proto kernel metric 256 pref medium
fc00:2::/64 dev veth_A-R2 proto kernel metric 256 pref medium
fc00:4::1 via fc00:2::2 dev veth_A-R2 metric 1024 pref medium
fe80::/64 dev veth_A-R1 proto kernel metric 256 pref medium
fe80::/64 dev veth_A-R2 proto kernel metric 256 pref medium
default via fc00:1::2 dev veth_A-R1 metric 1024 pref medium
# ip -6 route list cache
fc00:4::1 via fc00:2::2 dev veth_A-R2 metric 1024 expires 593sec mtu 1500 pref medium
fc00:3::1 via fc00:1::2 dev veth_A-R1 metric 1024 expires 593sec mtu 1500 pref medium
# ip -6 route flush cache # node for default route is discarded
Failed to send flush request: No such process
# ip -6 route list cache
fc00:3::1 via fc00:1::2 dev veth_A-R1 metric 1024 expires 586sec mtu 1500 pref medium
Check right away if the node has a RTN_RTINFO flag, before replacing the
'prev' pointer, that indicates the longest matching prefix found so far.
Fixes: 38fbeeeecc ("ipv6: prepare fib6_locate() for exception table")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 2b760fcf5c ("ipv6: hook up exception table to store dst
cache"), route exceptions reside in a separate hash table, and won't be
found by walking the FIB, so they won't be dumped to userspace on a
RTM_GETROUTE message.
This causes 'ip -6 route list cache' and 'ip -6 route flush cache' to
have no function anymore:
# ip -6 route get fc00:3::1
fc00:3::1 via fc00:1::2 dev veth_A-R1 src fc00:1::1 metric 1024 expires 539sec mtu 1400 pref medium
# ip -6 route get fc00:4::1
fc00:4::1 via fc00:2::2 dev veth_A-R2 src fc00:2::1 metric 1024 expires 536sec mtu 1500 pref medium
# ip -6 route list cache
# ip -6 route flush cache
# ip -6 route get fc00:3::1
fc00:3::1 via fc00:1::2 dev veth_A-R1 src fc00:1::1 metric 1024 expires 520sec mtu 1400 pref medium
# ip -6 route get fc00:4::1
fc00:4::1 via fc00:2::2 dev veth_A-R2 src fc00:2::1 metric 1024 expires 519sec mtu 1500 pref medium
because iproute2 lists cached routes using RTM_GETROUTE, and flushes them
by listing all the routes, and deleting them with RTM_DELROUTE one by one.
If cached routes are requested using the RTM_F_CLONED flag together with
strict checking, or if no strict checking is requested (and hence we can't
consistently apply filters), look up exceptions in the hash table
associated with the current fib6_info in rt6_dump_route(), and, if present
and not expired, add them to the dump.
We might be unable to dump all the entries for a given node in a single
message, so keep track of how many entries were handled for the current
node in fib6_walker, and skip that amount in case we start from the same
partially dumped node.
When a partial dump restarts, as the starting node might change when
'sernum' changes, we have no guarantee that we need to skip the same
amount of in-node entries. Therefore, we need two counters, and we need to
zero the in-node counter if the node from which the dump is resumed
differs.
Note that, with the current version of iproute2, this only fixes the
'ip -6 route list cache': on a flush command, iproute2 doesn't pass
RTM_F_CLONED and, due to this inconsistency, 'ip -6 route flush cache' is
still unable to fetch the routes to be flushed. This will be addressed in
a patch for iproute2.
To flush cached routes, a procfs entry could be introduced instead: that's
how it works for IPv4. We already have a rt6_flush_exception() function
ready to be wired to it. However, this would not solve the issue for
listing.
Versions of iproute2 and kernel tested:
iproute2
kernel 4.14.0 4.15.0 4.19.0 5.0.0 5.1.0 5.1.0, patched
3.18 list + + + + + +
flush + + + + + +
4.4 list + + + + + +
flush + + + + + +
4.9 list + + + + + +
flush + + + + + +
4.14 list + + + + + +
flush + + + + + +
4.15 list
flush
4.19 list
flush
5.0 list
flush
5.1 list
flush
with list + + + + + +
fix flush + + + +
v7:
- Explain usage of "skip" counters in commit message (suggested by
David Ahern)
v6:
- Rebase onto net-next, use recently introduced nexthop walker
- Make rt6_nh_dump_exceptions() a separate function (suggested by David
Ahern)
v5:
- Use dump_routes and dump_exceptions from filter, ignore NLM_F_MATCH,
update test results (flushing works with iproute2 < 5.0.0 now)
v4:
- Split NLM_F_MATCH and strict check handling in separate patches
- Filter routes using RTM_F_CLONED: if it's not set, only return
non-cached routes, and if it's set, only return cached routes:
change requested by David Ahern and Martin Lau. This implies that
iproute2 needs a separate patch to be able to flush IPv6 cached
routes. This is not ideal because we can't fix the breakage caused
by 2b760fcf5c entirely in kernel. However, two years have passed
since then, and this makes it more tolerable
v3:
- More descriptive comment about expired exceptions in rt6_dump_route()
- Swap return values of rt6_dump_route() (suggested by Martin Lau)
- Don't zero skip_in_node in case we don't dump anything in a given pass
(also suggested by Martin Lau)
- Remove check on RTM_F_CLONED altogether: in the current UAPI semantic,
it's just a flag to indicate the route was cloned, not to filter on
routes
v2: Add tracking of number of entries to be skipped in current node after
a partial dump. As we restart from the same node, if not all the
exceptions for a given node fit in a single message, the dump will
not terminate, as suggested by Martin Lau. This is a concrete
possibility, setting up a big number of exceptions for the same route
actually causes the issue, suggested by David Ahern.
Reported-by: Jianlin Shi <jishi@redhat.com>
Fixes: 2b760fcf5c ("ipv6: hook up exception table to store dst cache")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the next patch, we are going to add optional dump of exceptions to
rt6_dump_route().
Change the return code of rt6_dump_route() to accomodate partial node
dumps: we might dump multiple routes per node, and might be able to dump
only a given number of them, so fib6_dump_node() will need to know how
many routes have been dumped on partial dump, to restart the dump from the
point where it was interrupted.
Note that fib6_dump_node() is the only caller and already handles all
non-negative return codes as success: those become -1 to signal that we're
done with the node. If we fail, return 0, as we were unable to dump the
single route in the node, but we're not done with it.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If fc_nh_id isn't set, we shouldn't try to match against it. This
actually matters just for the RTF_CACHE below (where this case is
already handled): if iproute2 gets a route exception and tries to
delete it, it won't reference it by fc_nh_id, even if a nexthop
object might be associated to the originating route.
Fixes: 5b98324ebe ("ipv6: Allow routes to use nexthop objects")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 08e814c9e8: as we
are preparing to fix listing and dumping of IPv6 cached routes, we
need to allow RTM_F_CLONED as a flag to match routes against while
dumping them.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patches add back the ability to dump IPv4 and IPv6 exception
routes, and we need to allow selection of regular routes or exceptions.
Use RTM_F_CLONED as filter to decide whether to dump routes or exceptions:
iproute2 passes it in dump requests (except for IPv6 cache flush requests,
this will be fixed in iproute2) and this used to work as long as
exceptions were stored directly in the FIB, for both IPv4 and IPv6.
Caveat: if strict checking is not requested (that is, if the dump request
doesn't go through ip_valid_fib_dump_req()), we can't filter on protocol,
tables or route types.
In this case, filtering on RTM_F_CLONED would be inconsistent: we would
fix 'ip route list cache' by returning exception routes and at the same
time introduce another bug in case another selector is present, e.g. on
'ip route list cache table main' we would return all exception routes,
without filtering on tables.
Keep this consistent by applying no filters at all, and dumping both
routes and exceptions, if strict checking is not requested. iproute2
currently filters results anyway, and no unwanted results will be
presented to the user. The kernel will just dump more data than needed.
v7: No changes
v6: Rebase onto net-next, no changes
v5: New patch: add dump_routes and dump_exceptions flags in filter and
simply clear the unwanted one if strict checking is enabled, don't
ignore NLM_F_MATCH and don't set filter_set if NLM_F_MATCH is set.
Skip filtering altogether if no strict checking is requested:
selecting routes or exceptions only would be inconsistent with the
fact we can't filter on tables.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For tx path, in most cases, we still have to take refcnt on the dst
cause the caller is caching the dst somewhere. But it still is
beneficial to make use of RT6_LOOKUP_F_DST_NOREF flag while doing the
route lookup. It is cause this flag prevents manipulating refcnt on
net->ipv6.ip6_null_entry when doing fib6_rule_lookup() to traverse each
routing table. The null_entry is a shared object and constant updates on
it cause false sharing.
We converted the current major lookup function ip6_route_output_flags()
to make use of RT6_LOOKUP_F_DST_NOREF.
Together with the change in the rx path, we see noticable performance
boost:
I ran synflood tests between 2 hosts under the same switch. Both hosts
have 20G mlx NIC, and 8 tx/rx queues.
Sender sends pure SYN flood with random src IPs and ports using trafgen.
Receiver has a simple TCP listener on the target port.
Both hosts have multiple custom rules:
- For incoming packets, only local table is traversed.
- For outgoing packets, 3 tables are traversed to find the route.
The packet processing rate on the receiver is as follows:
- Before the fix: 3.78Mpps
- After the fix: 5.50Mpps
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6_route_input() is the key function to do the route lookup in the
rx data path. All the callers to this function are already holding rcu
lock. So it is fairly easy to convert it to not take refcnt on the dst:
We pass in flag RT6_LOOKUP_F_DST_NOREF and do skb_dst_set_noref().
This saves a few atomic inc or dec operations and should boost
performance overall.
This also makes the logic more aligned with v4.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch specifically converts the rule lookup logic to honor this
flag and not release refcnt when traversing each rule and calling
lookup() on each routing table.
Similar to previous patch, we also need some special handling of dst
entries in uncached list because there is always 1 refcnt taken for them
even if RT6_LOOKUP_F_DST_NOREF flag is set.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize rt6->rt6i_uncached on the following pre-allocated dsts:
net->ipv6.ip6_null_entry
net->ipv6.ip6_prohibit_entry
net->ipv6.ip6_blk_hole_entry
This is a preparation patch for later commits to be able to distinguish
dst entries in uncached list by doing:
!list_empty(rt6->rt6i_uncached)
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new flag is to instruct the route lookup function to not take
refcnt on the dst entry. The user which does route lookup with this flag
must properly use rcu protection.
ip6_pol_route() is the major route lookup function for both tx and rx
path.
In this function:
Do not take refcnt on dst if RT6_LOOKUP_F_DST_NOREF flag is set, and
directly return the route entry. The caller should be holding rcu lock
when using this flag, and decide whether to take refcnt or not.
One note on the dst cache in the uncached_list:
As uncached_list does not consume refcnt, one refcnt is always returned
back to the caller even if RT6_LOOKUP_F_DST_NOREF flag is set.
Uncached dst is only possible in the output path. So in such call path,
caller MUST check if the dst is in the uncached_list before assuming
that there is no refcnt taken on the returned dst.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix leak of unqueued fragments in ipv6 nf_defrag, from Guillaume
Nault.
2) Don't access the DDM interface unless the transceiver implements it
in bnx2x, from Mauro S. M. Rodrigues.
3) Don't double fetch 'len' from userspace in sock_getsockopt(), from
JingYi Hou.
4) Sign extension overflow in lio_core, from Colin Ian King.
5) Various netem bug fixes wrt. corrupted packets from Jakub Kicinski.
6) Fix epollout hang in hvsock, from Sunil Muthuswamy.
7) Fix regression in default fib6_type, from David Ahern.
8) Handle memory limits in tcp_fragment more appropriately, from Eric
Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (24 commits)
tcp: refine memory limit test in tcp_fragment()
inet: clear num_timeout reqsk_alloc()
net: mvpp2: debugfs: Add pmap to fs dump
ipv6: Default fib6_type to RTN_UNICAST when not set
net: hns3: Fix inconsistent indenting
net/af_iucv: always register net_device notifier
net/af_iucv: build proper skbs for HiperTransport
net/af_iucv: remove GFP_DMA restriction for HiperTransport
net: dsa: mv88e6xxx: fix shift of FID bits in mv88e6185_g1_vtu_loadpurge()
hvsock: fix epollout hang from race condition
net/udp_gso: Allow TX timestamp with UDP GSO
net: netem: fix use after free and double free with packet corruption
net: netem: fix backlog accounting for corrupted GSO frames
net: lio_core: fix potential sign-extension overflow on large shift
tipc: pass tunnel dev as NULL to udp_tunnel(6)_xmit_skb
ip6_tunnel: allow not to count pkts on tstats by passing dev as NULL
ip_tunnel: allow not to count pkts on tstats by setting skb's dev to NULL
tun: wake up waitqueues after IFF_UP is set
net: remove duplicate fetch in sock_getsockopt
tipc: fix issues with early FAILOVER_MSG from peer
...
Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update for
5.2. It contains all of the remaining GPLv2 and GPLv2+ updates that
were "easy" to determine by pattern matching. The ones after this are
going to be a bit more difficult and the people on the spdx list will be
discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud, always
nice to see in a diffstat.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXQyQYA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymnGQCghETUBotn1p3hTjY56VEs6dGzpHMAnRT0m+lv
kbsjBGEJpLbMRB2krnaU
=RMcT
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull still more SPDX updates from Greg KH:
"Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update
for 5.2. It contains all of the remaining GPLv2 and GPLv2+ updates
that were "easy" to determine by pattern matching. The ones after this
are going to be a bit more difficult and the people on the spdx list
will be discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud,
always nice to see in a diffstat"
* tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (65 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 507
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 506
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 505
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 504
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 503
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 502
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 501
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 499
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 498
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 497
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 496
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 495
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 491
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 490
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 489
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 488
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 487
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 486
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 485
...
When either CONFIG_IPV6 or CONFIG_SYN_COOKIES are disabled, the kernel
fails to build:
include/linux/netfilter_ipv6.h:180:9: error: implicit declaration of function '__cookie_v6_init_sequence'
[-Werror,-Wimplicit-function-declaration]
return __cookie_v6_init_sequence(iph, th, mssp);
include/linux/netfilter_ipv6.h:194:9: error: implicit declaration of function '__cookie_v6_check'
[-Werror,-Wimplicit-function-declaration]
return __cookie_v6_check(iph, th, cookie);
net/ipv6/netfilter.c:237:26: error: use of undeclared identifier '__cookie_v6_init_sequence'; did you mean 'cookie_init_sequence'?
net/ipv6/netfilter.c:238:21: error: use of undeclared identifier '__cookie_v6_check'; did you mean '__cookie_v4_check'?
Fix the IS_ENABLED() checks to match the function declaration
and definitions for these.
Fixes: 3006a5224f ("netfilter: synproxy: remove module dependency on IPv6 SYNPROXY")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
A user reported that routes are getting installed with type 0 (RTN_UNSPEC)
where before the routes were RTN_UNICAST. One example is from accel-ppp
which apparently still uses the ioctl interface and does not set
rtmsg_type. Another is the netlink interface where ipv6 does not require
rtm_type to be set (v4 does). Prior to the commit in the Fixes tag the
ipv6 stack converted type 0 to RTN_UNICAST, so restore that behavior.
Fixes: e8478e80e5 ("net/ipv6: Save route type in rt6_info")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
1) Module autoload for masquerade and redirection does not work.
2) Leak in unqueued packets in nf_ct_frag6_queue(). Ignore duplicated
fragments, pretend they are placed into the queue. Patches from
Guillaume Nault.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Both listeners - mlxsw and netdevsim - of IPv6 FIB notifications are now
ready to handle IPv6 multipath notifications.
Therefore, stop ignoring such notifications in both drivers and stop
sending notification for each added / deleted nexthop.
v2:
* Remove 'multipath_rt' from 'struct fib6_entry_notifier_info'
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If all the nexthops of a multipath route are being deleted, send one
notification for the entire route, instead of one per-nexthop.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Emit a notification when a multipath routes is added or replace.
Note that unlike the replace notifications sent from fib6_add_rt2node(),
it is possible we are sending a 'FIB_EVENT_ENTRY_REPLACE' when a route
was merely added and not replaced.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the IPv6 FIB notifier info with number of sibling routes being
notified.
This will later allow listeners to process one notification for a
multipath routes instead of N, where N is the number of nexthops.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Lots of bug fixes here:
1) Out of bounds access in __bpf_skc_lookup, from Lorenz Bauer.
2) Fix rate reporting in cfg80211_calculate_bitrate_he(), from John
Crispin.
3) Use after free in psock backlog workqueue, from John Fastabend.
4) Fix source port matching in fdb peer flow rule of mlx5, from Raed
Salem.
5) Use atomic_inc_not_zero() in fl6_sock_lookup(), from Eric Dumazet.
6) Network header needs to be set for packet redirect in nfp, from
John Hurley.
7) Fix udp zerocopy refcnt, from Willem de Bruijn.
8) Don't assume linear buffers in vxlan and geneve error handlers,
from Stefano Brivio.
9) Fix TOS matching in mlxsw, from Jiri Pirko.
10) More SCTP cookie memory leak fixes, from Neil Horman.
11) Fix VLAN filtering in rtl8366, from Linus Walluij.
12) Various TCP SACK payload size and fragmentation memory limit fixes
from Eric Dumazet.
13) Use after free in pneigh_get_next(), also from Eric Dumazet.
14) LAPB control block leak fix from Jeremy Sowden"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (145 commits)
lapb: fixed leak of control-blocks.
tipc: purge deferredq list for each grp member in tipc_group_delete
ax25: fix inconsistent lock state in ax25_destroy_timer
neigh: fix use-after-free read in pneigh_get_next
tcp: fix compile error if !CONFIG_SYSCTL
hv_sock: Suppress bogus "may be used uninitialized" warnings
be2net: Fix number of Rx queues used for flow hashing
net: handle 802.1P vlan 0 packets properly
tcp: enforce tcp_min_snd_mss in tcp_mtu_probing()
tcp: add tcp_min_snd_mss sysctl
tcp: tcp_fragment() should apply sane memory limits
tcp: limit payload size of sacked skbs
Revert "net: phylink: set the autoneg state in phylink_phy_change"
bpf: fix nested bpf tracepoints with per-cpu data
bpf: Fix out of bounds memory access in bpf_sk_storage
vsock/virtio: set SOCK_DONE on peer shutdown
net: dsa: rtl8366: Fix up VLAN filtering
net: phylink: set the autoneg state in phylink_phy_change
net: add high_order_alloc_disable sysctl/static key
tcp: add tcp_tx_skb_cache sysctl
...
Add common functions into nf_synproxy_core.c to prepare for nftables support.
The prototypes of the functions used by {ipt, ip6t}_SYNPROXY are in the new
file nf_synproxy.h
Signed-off-by: Fernando Fernandez Mancera <ffmancera@riseup.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This is a prerequisite for the infrastructure module NETFILTER_SYNPROXY.
The new module is needed to avoid duplicated code for the SYNPROXY
nftables support.
Signed-off-by: Fernando Fernandez Mancera <ffmancera@riseup.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This was originally passed through to the VRF logic in compute_score().
But that logic has now been replaced by udp_sk_bound_dev_eq() and so
this code is no longer used or needed.
Signed-off-by: Tim Beale <timbeale@catalyst.net.nz>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Originally this was used by the VRF logic in compute_score(), but that
was later replaced by udp_sk_bound_dev_eq() and the parameter became
unused.
Note this change adds an 'unused variable' compiler warning that will be
removed in the next patch (I've split the removal in two to make review
slightly easier).
Signed-off-by: Tim Beale <timbeale@catalyst.net.nz>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we want to set a EDT time for the skb we want to send
via ip_send_unicast_reply(), we have to pass a new parameter
and initialize ipc.sockc.transmit_time with it.
This fixes the EDT time for ACK/RST packets sent on behalf of
a TIME_WAIT socket.
Fixes: a842fe1425 ("tcp: add optional per socket transmit delay")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kbuild documentation clearly shows that the documents
there are written at different times: some use markdown,
some use their own peculiar logic to split sections.
Convert everything to ReST without affecting too much
the author's style and avoiding adding uneeded markups.
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Adding delays to TCP flows is crucial for studying behavior
of TCP stacks, including congestion control modules.
Linux offers netem module, but it has unpractical constraints :
- Need root access to change qdisc
- Hard to setup on egress if combined with non trivial qdisc like FQ
- Single delay for all flows.
EDT (Earliest Departure Time) adoption in TCP stack allows us
to enable a per socket delay at a very small cost.
Networking tools can now establish thousands of flows, each of them
with a different delay, simulating real world conditions.
This requires FQ packet scheduler or a EDT-enabled NIC.
This patchs adds TCP_TX_DELAY socket option, to set a delay in
usec units.
unsigned int tx_delay = 10000; /* 10 msec */
setsockopt(fd, SOL_TCP, TCP_TX_DELAY, &tx_delay, sizeof(tx_delay));
Note that FQ packet scheduler limits might need some tweaking :
man tc-fq
PARAMETERS
limit
Hard limit on the real queue size. When this limit is
reached, new packets are dropped. If the value is lowered,
packets are dropped so that the new limit is met. Default
is 10000 packets.
flow_limit
Hard limit on the maximum number of packets queued per
flow. Default value is 100.
Use of TCP_TX_DELAY option will increase number of skbs in FQ qdisc,
so packets would be dropped if any of the previous limit is hit.
Use of a jump label makes this support runtime-free, for hosts
never using the option.
Also note that TSQ (TCP Small Queues) limits are slightly changed
with this patch : we need to account that skbs artificially delayed
wont stop us providind more skbs to feed the pipe (netem uses
skb_orphan_partial() for this purpose, but FQ can not use this trick)
Because of that, using big delays might very well trigger
old bugs in TSO auto defer logic and/or sndbuf limited detection.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get the ingress interface and increment ICMP counters based on that
instead of skb->dev when the the dev is a VRF device.
This is a follow up on the following message:
https://www.spinics.net/lists/netdev/msg560268.html
v2: Avoid changing skb->dev since it has unintended effect for local
delivery (David Ahern).
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The below patch fixes an incorrect zerocopy refcnt increment when
appending with MSG_MORE to an existing zerocopy udp skb.
send(.., MSG_ZEROCOPY | MSG_MORE); // refcnt 1
send(.., MSG_ZEROCOPY | MSG_MORE); // refcnt still 1 (bar frags)
But it missed that zerocopy need not be passed at the first send. The
right test whether the uarg is newly allocated and thus has extra
refcnt 1 is not !skb, but !skb_zcopy.
send(.., MSG_MORE); // <no uarg>
send(.., MSG_ZEROCOPY); // refcnt 1
Fixes: 100f6d8e09 ("net: correct zerocopy refcnt with udp MSG_MORE")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for RTA_NH_ID attribute to allow a user to specify a
nexthop id to use with a route. fc_nh_id is added to fib6_config to
hold the value passed in the RTA_NH_ID attribute. If a nexthop id
is given, the gateway, device, encap and multipath attributes can
not be set.
Update ip6_route_del to check metric and protocol before nexthop
specs. If fc_nh_id is set, then it must match the id in the route
entry. Since IPv6 allows delete of a cached entry (an exception),
add ip6_del_cached_rt_nh to cycle through all of the fib6_nh in
a fib entry if it is using a nexthop.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use nexthop_for_each_fib6_nh to call fib6_nh_mtu_change for each
fib6_nh in a nexthop for rt6_mtu_change_route. For __ip6_rt_update_pmtu,
we need to find the nexthop that correlates to the device and gateway
in the rt6_info.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use nexthop_for_each_fib6_nh and fib6_nh_find_match to find the
fib6_nh in a nexthop that correlates to the device and gateway
in the rt6_info.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a hook in __ip6_route_redirect to handle a nexthop struct in a
fib6_info. Use nexthop_for_each_fib6_nh and fib6_nh_redirect_match
to call ip6_redirect_nh_match for each fib6_nh looking for a match.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a hook in rt6_flush_exceptions, rt6_remove_exception_rt,
rt6_update_exception_stamp_rt, and rt6_age_exceptions to handle
nexthop struct in a fib6_info.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
