Channels are probed, but actual event handling is still stubbed out.
Stub implementation of check_caps is needed because ptp.c will call into
it from efx_ptp_use_mac_tx_timestamps() to decide if it wants TXQs.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We handle everything ourselves in ef100_reset(), rather than relying on
the generic down/up routines.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can't actually do the MCDI to probe it fully until we have working
MCDI, which comes later, but we need efx->phy_data to be allocated so
that when we get MCDI events the link-state change handler doesn't
NULL-dereference.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't actually do the efx_mcdi_reset() because we don't have MCDI yet.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No TX or RX path, no MCDI, not even an ifup/down handler.
Besides stubs, the bulk of the patch deals with reading the Xilinx
extended PCIe capability, which tells us where to find our BAR.
Though in the same module, EF100 has its own struct pci_driver,
which is named sfc_ef100.
A small number of additional nic_type methods are added; those in the
TX (tx_enqueue) and RX (rx_packet) paths are called through indirect
call wrappers to minimise the performance impact.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EF100 adds a few new valid addresses for efx_writed_page(), as well as
a Function Control Window in the BAR whose location is variable.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An MDIO-based n-way restart does not make sense for any of the NICs
supported by this driver, nor for the coming EF100.
Unlike on Falcon (which was already split off into a separate driver),
the PHY on all of Siena, EF10 and EF100 is managed by MC firmware.
While Siena can talk to the PHY over MDIO, doing so for anything other
than debugging purposes (mdio_mii_ioctl) is likely to confuse the
firmware.
(According to the SFC firmware team, this support was originally added
to the Siena driver early in the development of that product, before
it was decided to have firmware manage the PHY.)
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan reports static checker warning:
"The patch 9b6ee3cf95: "qed: sanitize PBL chains allocation" from Jul
23, 2020, leads to the following static checker warning:
drivers/net/ethernet/qlogic/qed/qed_chain.c:299 qed_chain_alloc_pbl()
error: uninitialized symbol 'pbl_virt'.
drivers/net/ethernet/qlogic/qed/qed_chain.c
249 static int qed_chain_alloc_pbl(struct qed_dev *cdev, struct qed_chain *chain)
250 {
251 struct device *dev = &cdev->pdev->dev;
252 struct addr_tbl_entry *addr_tbl;
253 dma_addr_t phys, pbl_phys;
254 __le64 *pbl_virt;
^^^^^^^^^^^^^^^^
[...]
271 if (chain->b_external_pbl)
272 goto alloc_pages;
^^^^^^^^^^^^^^^^ uninitialized
[...]
298 /* Fill the PBL table with the physical address of the page */
299 pbl_virt[i] = cpu_to_le64(phys);
^^^^^^^^^^^
[...]
"
This issue was introduced with commit c3a321b06a ("qed: simplify
initialization of the chains with an external PBL"), when
chain->pbl_sp.table_virt initialization was moved up to
qed_chain_init_params().
Fix it by initializing pbl_virt with an already filled chain struct field.
Fixes: c3a321b06a ("qed: simplify initialization of the chains with an external PBL")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to dump PXP registers and PCIe statistics.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now we can report all the full 64-bit CPU endian software accumulated
counters instead of the hw counters, some of which may be less than
64-bit wide. Define the necessary macros to access the software
counters.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have the infrastructure in place, add the new function
bnxt_accumulate_all_stats() to periodically accumulate and check for
counter rollover of all ring stats and port stats.
A chip bug was also discovered that could cause some ring counters to
become 0 during DMA. Workaround by ignoring zeros on the affected
chips.
Some older frimware will reset port counters during ifdown. We need
to check for that and free the accumulated port counters during ifdown
to prevent bogus counter overflow detection during ifup.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If supported by newer firmware, make the firmware call to query all
the port counter masks. If not supported, assume 40-bit port
counter masks.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer firmware has a new call HWRM_FUNC_QSTATS_EXT to retrieve the
masks of all ring counters. Make this call when supported to
initialize the hardware masks of all ring counters. If the call
is not available, assume 48-bit ring counter masks on P5 chips.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of these DMAed hardware counters are not full 64-bit counters and
so we need to accumulate them as they overflow. Allocate copies of these
DMA statistics memory blocks with the same size for accumulation. The
hardware counter widths are also counter specific so we allocate
memory for masks that correspond to each counter.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver manages multiple statistics structures of different sizes.
They are all allocated, freed, and handled practically the same. Define
a new bnxt_stats_mem structure and common allocation and free functions
for all staistics memory blocks.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port statistics structures have hard coded padding and offset.
Define macros to make this look cleaner.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Main changes are 200G support and fixing the definitions of discard and
error counters to match the hardware definitions.
Because the HWRM_PORT_PHY_QCFG message size has now exceeded the max.
encapsulated response message size of 96 bytes from the PF to the VF,
we now need to cap this message to 96 bytes for forwarding. The forwarded
response only needs to contain the basic link status and speed information
and can be capped without adding the new information.
v2: Fix bnxt_re compile error.
Cc: Selvin Xavier <selvin.xavier@broadcom.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove PCIe non-counters display from ethtool statistics, as
they are not simple counters but register dump. The next few
patches will add logic to detect counter roll-over and it won't
work with these PCIe non-counters.
There will be a follow up patch to get PCIe information via
ethtool register dump.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
list_for_each_safe is able to handle an empty list.
The only effect of avoiding the loop is not initializing the
index variable.
Drop list_empty tests in cases where these variables are not
used.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
<smpl>
@@
expression x,e;
iterator name list_for_each_safe;
statement S;
identifier i,j;
@@
-if (!(list_empty(x))) {
list_for_each_safe(i,j,x) S
- }
... when != i
when != j
(
i = e;
|
? j = e;
)
</smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/intel/igc/igc_mac.c:424 igc_check_for_copper_link()
error: uninitialized symbol 'link'.
This patch come to fix this warning and initialize the 'link' symbol.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 707abf0695 ("igc: Add initial LTR support")
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove ictxptc, ictxatc, cbtmpc, cbrdpc, cbrmpc and htcbdpc fields from
the hw_stats structure. Accordance to the i225 device
specification these fields not in use.
This patch come to clean up the driver code.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
collision_delta, tx_packet_delta, txcw, adaptive_ifs and
has_fwsm fields not in use.
This patch come to clean up the driver code.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
LED control currently not implemented.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
IGC_ICTXPTC and IGC_ICTXATC are already defined elsewhere, remove this
double definition. Also, remove unneeded registers as they are not
applicable to i225 devices.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tx Queue Min Threshold Count register no applicable for the i225 device.
This patch comes to clean up it.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The statistics of this register are being tracked, however, the register
was inadvertently missed when implementing igc_clear_hw_cntrs_base().
The register is clear on read, so add it to the function so that the
register is cleared when requested so the tracked count is accurate.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Though we are populating and tracking ictxqec, the value is not being used
for anything so remove it altogether and save the register read.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The UDP reuseport conflict was a little bit tricky.
The net-next code, via bpf-next, extracted the reuseport handling
into a helper so that the BPF sk lookup code could invoke it.
At the same time, the logic for reuseport handling of unconnected
sockets changed via commit efc6b6f6c3
which changed the logic to carry on the reuseport result into the
rest of the lookup loop if we do not return immediately.
This requires moving the reuseport_has_conns() logic into the callers.
While we are here, get rid of inline directives as they do not belong
in foo.c files.
The other changes were cases of more straightforward overlapping
modifications.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixed 2 issues with the usage of skb_cow in LAPB drivers
"lapbether" and "hdlc_x25":
1) After skb_cow fails, kfree_skb should be called to drop a reference
to the skb. But in both drivers, kfree_skb is not called.
2) skb_cow should be called before skb_push so that is can ensure the
safety of skb_push. But in "lapbether", it is incorrectly called after
skb_push.
More details about these 2 issues:
1) The behavior of calling kfree_skb on failure is also the behavior of
netif_rx, which is called by this function with "return netif_rx(skb);".
So this function should follow this behavior, too.
2) In "lapbether", skb_cow is called after skb_push. This results in 2
logical issues:
a) skb_push is not protected by skb_cow;
b) An extra headroom of 1 byte is ensured after skb_push. This extra
headroom has no use in this function. It also has no use in the
upper-layer function that this function passes the skb to
(x25_lapb_receive_frame in net/x25/x25_dev.c).
So logically skb_cow should instead be called before skb_push.
Cc: Eric Dumazet <edumazet@google.com>
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the chips in the mv88e6xxx family don't support jumbo
configuration per port. But they do have a chip-wide max frame size that
can be used. Use this to approximate the behaviour of configuring a port
based MTU.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MV88E6190 and MV88E6190X both support per port jumbo configuration
just like the other GE switches. Install the appropriate ops.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MV88E6097 chip does not support configuring jumbo frames. Prior to
commit 5f4366660d only the 6352, 6351, 6165 and 6320 chips configured
jumbo mode. The refactor accidentally added the function for the 6097.
Remove the erroneous function pointer assignment.
Fixes: 5f4366660d ("net: dsa: mv88e6xxx: Refactor setting of jumbo frames")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove casting the values returned by memory allocation function.
Coccinelle emits WARNING:
./drivers/net/ethernet/hisilicon/hix5hd2_gmac.c:1027:9-23: WARNING:
casting value returned by memory allocation function to (struct sg_desc *) is useless.
This issue was detected by using the Coccinelle software.
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Second set of fixes for v5.8, and hopefully also the last. Three
important regressions fixed.
ath9k
* fix a regression which broke support for all ath9k usb devices
ath10k
* fix a regression which broke support for all QCA4019 AHB devices
iwlwifi
* fix a regression which broke support for some Killer Wireless-AC 1550 cards
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJfGukwAAoJEG4XJFUm622bIdwIAKYV3lplb6mXyDdF1b3Yoxar
0IDUglXlJN+VIgvUQG4wOvxgDw7jp6q95BRi58VjafIFm+orjILvYFmwThLPYfIS
dA0ML9+zGnRMC+SIjZktXKG9lridQXyqexWHCFF9dT147GsF8+LIbfqT6denCLf7
vP26RSMAMK5Ed01V9qb5rtitaVbr+Bx+c7adV8tLH/gkWeTEp4CaDhNOkMJ0uRCV
QPZ8duF1Hz/QVMn9PAA8xGTH4bxIfSfWVJfSjG1uq349CZ+MjHleDeYWKh524ThV
49YTabR2DIKOWSgNzG7jsitz7K/420Y/NpuNeGWO+7czgYe2uEIrGDZkYPUPoS4=
=PTR1
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-2020-07-24' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.8
Second set of fixes for v5.8, and hopefully also the last. Three
important regressions fixed.
ath9k
* fix a regression which broke support for all ath9k usb devices
ath10k
* fix a regression which broke support for all QCA4019 AHB devices
iwlwifi
* fix a regression which broke support for some Killer Wireless-AC 1550 cards
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a potential race in xennet_remove(); this is what the driver is
doing upon unregistering a network device:
1. state = read bus state
2. if state is not "Closed":
3. request to set state to "Closing"
4. wait for state to be set to "Closing"
5. request to set state to "Closed"
6. wait for state to be set to "Closed"
If the state changes to "Closed" immediately after step 1 we are stuck
forever in step 4, because the state will never go back from "Closed" to
"Closing".
Make sure to check also for state == "Closed" in step 4 to prevent the
deadlock.
Also add a 5 sec timeout any time we wait for the bus state to change,
to avoid getting stuck forever in wait_event().
Signed-off-by: Andrea Righi <andrea.righi@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2020-07-23
This series contains updates to ice driver only.
Jake refactors ice_discover_caps() to reduce the number of AdminQ calls
made. Splits ice_parse_caps() to separate functions to update function
and device capabilities separately to allow for updating outside of
initialization.
Akeem adds power management support.
Paul G refactors FC and FEC code to aid in restoring of PHY settings
on media insertion. Implements lenient mode and link override support.
Adds link debug info and formats existing debug info to be more
readable. Adds support to check and report additional autoneg
capabilities. Implements the capability to detect media cage in order to
differentiate AUI types as Direct Attach or backplane.
Bruce implements Total Port Shutdown for devices that support it.
Lev renames low_power_ctrl field to lower_power_ctrl_an to be more
descriptive of the field.
Doug reports AOC types as media type fiber.
Paul S adds code to handle 1G SGMII PHY type.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
An imbalanced TX indirection table causes netvsc to have low
performance. This table is created and managed during runtime. To help
better diagnose performance issues caused by imbalanced tables, it needs
make TX indirection tables visible.
Because TX indirection table is driver specified information, so
display it via ethtool register dump.
Signed-off-by: Chi Song <chisong@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Randy reported compile failure when CONFIG_SYSCTL is not set/enabled:
ERROR: modpost: "sysctl_vals" [drivers/net/vrf.ko] undefined!
Fix by splitting out the sysctl init and cleanup into helpers that
can be set to do nothing when CONFIG_SYSCTL is disabled. In addition,
move vrf_strict_mode and vrf_strict_mode_change to above
vrf_shared_table_handler (code move only) and wrap all of it
in the ifdef CONFIG_SYSCTL.
Update the strict mode tests to check for the existence of the
/proc/sys entry.
Fixes: 33306f1aaf ("vrf: add sysctl parameter for strict mode")
Cc: Andrea Mayer <andrea.mayer@uniroma2.it>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David Ahern <dsahern@kernel.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: David S. Miller <davem@davemloft.net>
There isn't a case for 1G SGMII in ice_get_media_type() so add
the handling for it.
Also handle the special case where some direct attach
cables may report that they support 1G SGMII, but
that is erroneous since SGMII is supposed to be a
backplane media type (between a MAC and a PHY). If
the driver doesn't handle this special case then a
user could see the 'Port' in ethtool change from
'Direct attach Copper' to 'Backplane' when they have
forced the speed to 1G, but the cable hasn't changed.
Lastly, change ice_aq_get_phy_caps() to save the
module_type info if the function was called with
ICE_AQC_REPORT_TOPO_CAP. This call uses the media
information to populate the module_type. If no
media is present then the values in module_type
will be 0.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Report AOC types as fiber instead of unknown.
Signed-off-by: Doug Dziggel <douglas.a.dziggel@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add AQC get link topology handle support. This is needed to determine
Direct Attach (DA) or backplane media type for PHY types that support
either. Get link topology handle cage node type request can be used to
determine if a cage is present or not. If a cage is present for PHY
types that supports both DA and backplane media type, then the media
type is DA, else the media type is backplane.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Rename the low_power_ctrl field to low_power_ctrl_an to be properly
descriptive of it being an autoneg field.
Signed-off-by: Lev Faerman <lev.faerman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Firmware now reports AN28, AN32, and AN73. Add a helper and check these new
values and report PHY autoneg capability.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add debug logs for ice_aq_get_phy_caps(), and format
ice_aq_set_phy_cfg() and ice_aq_get_link_info() debug logs to make them
more readable.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When the Port Disable bit is set in the Link Default Override Mask TLV PFA
module in the NVM, Total Port Shutdown mode is supported and enabled. In
this mode, the driver should act as if the link-down-on-close ethtool
private flag is always enabled and dis-allow any change to that flag.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Adds functions to check for link override firmware support and get
the override settings for a port. The previously supported/default link
mode was strict mode.
In strict mode link is configured based on get PHY capabilities PHY types
with media.
Lenient mode is now the default link mode. In lenient mode the link is
configured based on get PHY capabilities PHY types without media. This
allows the user to configure link that the media does not report. Limit the
minimum supported link mode to 25G for devices that support 100G, and 1G
for devices that support less than 100G.
Default override is only supported in lenient mode. If default override
is supported and enabled, then default override values are used for
configuring speed and FEC. Default override provide persistent link
settings in the NVM.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Evan Swanson <evan.swanson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
geneve_nl2info() sets 'df' conditionally, so we have to
initialize it by copying the value from existing geneve
device in geneve_changelink().
Fixes: 56c09de347 ("geneve: allow changing DF behavior after creation")
Reported-by: syzbot+7ebc2e088af5e4c0c9fa@syzkaller.appspotmail.com
Cc: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Very similar to commit 544f287b84
("bonding: check error value of register_netdevice() immediately"),
we should immediately check the return value of register_netdevice()
before doing anything else.
Fixes: 005db31d5f ("bonding: set carrier off for devices created through netlink")
Reported-and-tested-by: syzbot+bbc3a11c4da63c1b74d6@syzkaller.appspotmail.com
Cc: Beniamino Galvani <bgalvani@redhat.com>
Cc: Taehee Yoo <ap420073@gmail.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the transition from no media to media FW will clear the
set-phy-cfg data set by the user. Save initial PHY settings and any
settings later requested by the user and use that data to restore PHY
settings on media insertion. Since PHY configuration is now being stored,
replace calls that were calling FW to get the configuration with the saved
copy.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The call to ice_cfg_phy_fec() requires the caller to perform certain
actions before calling it. Instead of imposing these preconditions move
the operations into the function and perform them ourselves.
Also, fix some style issues in nearby touched code.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Create a helper function for configuring requested flow control so that it
can be utilized by other functions looking to configure flow control
settings. Utilize the existing helper ice_copy_phy_caps_to_cfg() to copy a
PHY capability to configuration instead duplicating the code for it.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add callbacks needed to support advanced power management for Wake on LAN.
Also make ice_pf_state_is_nominal function available for all configurations
not just CONFIG_PCI_IOV.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Using the new ice_aq_list_caps and ice_parse_(dev|func)_caps functions,
replace ice_discover_caps with two functions that each take a pointer to
the dev_caps and func_caps structures respectively.
This makes the side effect of updating the hw->dev_caps and
hw->func_caps obvious from reading the implementation of the function.
Additionally, it opens the way for enabling reading of device
capabilities outside of the initialization flow. By passing in
a pointer, another caller will be able to read the capabilities without
modifying the HW capabilities structures.
As there are no other callers, it is safe to now remove
ice_aq_discover_caps and ice_parse_caps.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_parse_caps function is used to convert the capability block data
coming from firmware into a structured format used by other parts of the
code.
The current implementation directly updates the hw->func_caps and
hw->dev_caps structures. It is directly called from within
ice_aq_discover_caps. This causes the discover_caps function to have the
side effect of modifying the HW capability structures, which is not
intuitive.
Split this function into ice_parse_dev_caps and ice_parse_func_caps.
These functions will take a pointer to the dev_caps and func_caps
respectively. Also create an ice_parse_common_caps for sharing the
capability logic that is common to device and function.
Doing so enables a future refactor to allow reading and parsing
capabilities into a local caps structure instead of modifying the
members of the HW structure directly.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_discover_caps function is used to read the device and function
capabilities, updating the hardware capabilities structures with
relevant data.
The exact number of capabilities returned by the hardware is unknown
ahead of time. The AdminQ command will report the total number of
capabilities in the return buffer.
The current implementation involves requesting capabilities once,
reading this returned size, and then re-requested with that size.
This isn't really necessary. The firmware interface has a maximum size
of ICE_AQ_MAX_BUF_LEN. Firmware can never return more than
ICE_AQ_MAX_BUF_LEN / sizeof(struct ice_aqc_list_caps_elem) capabilities.
Avoid the retry loop by simply allocating a buffer of size
ICE_AQ_MAX_BUF_LEN. This is significantly simpler than retrying. The
extra allocation isn't a big deal, as it will be released after we
finish parsing the capabilities.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In this test, loopback pkt is created and sent on default queue.
The packet goes until the Multi Port Switch (MPS) just before
the MAC and based on the specified channel number, it either
goes outside the wire on one of the physical ports or looped
back to Rx path by MPS. In this case, we're specifying loopback
channel, instead of physical ports, so the packet gets looped
back to Rx path, instead of getting transmitted on the wire.
v3:
- Modify commit message to include test details.
v2:
- Add only loopback self-test.
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use eth_zero_addr() to clear mac address insetad of memset().
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check MC_CMD_DRV_ATTACH_EXT_OUT_FLAG_TRUSTED, before setting
the info, which will hopefully protect us from -EPERM errors
the previous code was gracefully ignoring. Ed reports this
is not the 100% correct bit, but it's the best approximation
we have. Shared code reports the port information back to user
space, so we really want to know what was added and what failed.
Ignoring -EPERM is not an option.
The driver does not call udp_tunnel_get_rx_info(), so its own
management of table state is not really all that problematic,
we can leave it be. This allows the driver to continue with its
copious table syncing, and matching the ports to TX frames,
which it will reportedly do one day.
Leave the feature checking in the callbacks, as the device may
remove the capabilities on reset.
Inline the loop from __efx_ef10_udp_tnl_lookup_port() into
efx_ef10_udp_tnl_has_port(), since it's the only caller now.
With new infra this driver gains port replace - when space frees
up in a full table a new port will be selected for offload.
Plus efx will no longer sleep in an atomic context.
v2:
- amend the commit message about TRUSTED not being 100%
- add TUNNEL_ENCAP_UDP_PORT_ENTRY_INVALID to mark unsed
entries
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-By: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the implementation of uld_send(), the skb is consumed on all
execution paths except one. Release skb when returning NET_XMIT_DROP.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add XDP_REDIRECT case handling and the corresponding NDO to support
redirecting XDP frames. This also includes registering driver memory
model (currently order-0 page mode) in BPF subsystem.
The total number of XDP queues is usually 1:1 with Rx ones.
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current XDP Tx logic is suboptimal and can't be reused for XDP_REDIRECT
path.
Make qede_xdp_{tx_int,xmit}() more universal and effective in general to
allow future expanding.
Misc: use unlikely() hints where appropriate and replace "fallthrough"
comments with pseudo-keywords.
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct the indentation of net_device_ops declarations for fancier look.
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the file more readable and easier for adding new fields.
Misc: use IFNAMSIZ and netdev_name() instead of sizeof_field()
and direct net_device::name dereferencing.
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend current infrastructure to store chain page size in a struct
and use it in all functions instead of fixed QED_CHAIN_PAGE_SIZE.
Its value remains the default one, but can be overridden in
qed_chain_init_params before chain allocation.
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To simplify qed_chain_alloc() prototype and call sites, introduce struct
qed_chain_init_params to specify chain params, and pass a pointer to
filled struct to the actual qed_chain_alloc() instead of a long list
of separate arguments.
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fill PBL table parameters for chains with an external PBL data earlier on
qed_chain_init_params() rather than on allocation itself. This simplifies
allocation code and allows to extend struct ext_pbl for other chain types.
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qed_chain_init*() are used in one file/place on "cold" path only, so they
can be uninlined and moved next to the call sites.
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PBL chain elements are actually DMA addresses stored in __le64, but
currently their size is hardcoded to 8, and DMA addresses are assigned
via cast to variable-sized dma_addr_t without any bitwise conversions.
Change the type of pbl_virt array to match the actual one, add a new
field to store the size of allocated DMA memory and sanitize elements
assignment.
Misc: give more logic names to the members of qed_chain::pbl_sp embedded
struct.
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Zero-initialize chain on qed_chain_free(), so it couldn't be freed
twice and provoke undefined behaviour.
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move chain allocation/freeing functions to a new file to not mix it with
hardware-related code.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
List one entry per line and sort them alphabetically to simplify the
addition of the new ones.
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes PTP on AQC10X.
PTP support on AQC10X requires FW involvement and FW configures the
TPS data arb mode itself.
So we must make sure driver doesn't touch TPS data arb mode on AQC10x
if PTP is enabled. Otherwise, there are no timestamps even though
packets are flowing.
Fixes: 2deac71ac4 ("net: atlantic: QoS implementation: min_rate")
Signed-off-by: Egor Pomozov <epomozov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when netdev fails to allocate the error return path
fails to free the allocated object 'lid'. Fix this by setting
err to the return error code and jumping to a new label that
performs the kfree of lid before returning.
Addresses-Coverity: ("Resource leak")
Fixes: 4b03b27349 ("ionic: get MTU from lif identity")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vlan tagged packets are getting dropped when used with DPDK that uses
the AF_PACKET interface on a hyperV guest.
The packet layer uses the tpacket interface to communicate the vlans
information to the upper layers. On Rx path, these drivers can read the
vlan info from the tpacket header but on the Tx path, this information
is still within the packet frame and requires the paravirtual drivers to
push this back into the NDIS header which is then used by the host OS to
form the packet.
This transition from the packet frame to NDIS header is currently missing
hence causing the host OS to drop the all vlan tagged packets sent by
the drivers that use AF_PACKET (ETH_P_ALL) such as DPDK.
Here is an overview of the changes in the vlan header in the packet path:
The RX path (userspace handles everything):
1. RX VLAN packet is stripped by HOST OS and placed in NDIS header
2. Guest Kernel RX hv_netvsc packets and moves VLAN info from NDIS
header into kernel SKB
3. Kernel shares packets with user space application with PACKET_MMAP.
The SKB VLAN info is copied to tpacket layer and indication set
TP_STATUS_VLAN_VALID.
4. The user space application will re-insert the VLAN info into the frame
The TX path:
1. The user space application has the VLAN info in the frame.
2. Guest kernel gets packets from the application with PACKET_MMAP.
3. The kernel later sends the frame to the hv_netvsc driver. The only way
to send VLANs is when the SKB is setup & the VLAN is stripped from the
frame.
4. TX VLAN is re-inserted by HOST OS based on the NDIS header. If it sees
a VLAN in the frame the packet is dropped.
Cc: xe-linux-external@cisco.com
Cc: Sriram Krishnan <srirakr2@cisco.com>
Signed-off-by: Sriram Krishnan <srirakr2@cisco.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable current_head_index is being initialized with a value that
is never read and it is being updated later with a new value. Replace
the initialization of -1 with the latter assignment.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For ENETC ports that register an external MDIO bus,
the bus doesn't get removed on the error bailout path
of enetc_pf_probe().
This issue became much more visible after recent:
commit 07095c025a ("net: enetc: Use DT protocol information to set up the ports")
Before this commit, one could make probing fail on the error
path only by having register_netdev() fail, which is unlikely.
But after this commit, because it moved the enetc_of_phy_get()
call up in the probing sequence, now we can trigger an mdiobus_free()
bug just by forcing enetc_alloc_msix() to return error, i.e. with the
'pci=nomsi' kernel bootarg (since ENETC relies on MSI support to work),
as the calltrace below shows:
kernel BUG at /home/eiz/work/enetc/net/drivers/net/phy/mdio_bus.c:648!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
[...]
Hardware name: LS1028A RDB Board (DT)
pstate: 80000005 (Nzcv daif -PAN -UAO BTYPE=--)
pc : mdiobus_free+0x50/0x58
lr : devm_mdiobus_free+0x14/0x20
[...]
Call trace:
mdiobus_free+0x50/0x58
devm_mdiobus_free+0x14/0x20
release_nodes+0x138/0x228
devres_release_all+0x38/0x60
really_probe+0x1c8/0x368
driver_probe_device+0x5c/0xc0
device_driver_attach+0x74/0x80
__driver_attach+0x8c/0xd8
bus_for_each_dev+0x7c/0xd8
driver_attach+0x24/0x30
bus_add_driver+0x154/0x200
driver_register+0x64/0x120
__pci_register_driver+0x44/0x50
enetc_pf_driver_init+0x24/0x30
do_one_initcall+0x60/0x1c0
kernel_init_freeable+0x1fc/0x274
kernel_init+0x14/0x110
ret_from_fork+0x10/0x34
Fixes: ebfcb23d62 ("enetc: Add ENETC PF level external MDIO support")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
enetc_imdio_remove() is missing from the enetc_pf_probe()
bailout path. Not surprisingly because enetc_setup_serdes()
is registering the imdio bus for internal purposes, and it's
not obvious that enetc_imdio_remove() currently performs the
teardown of enetc_setup_serdes().
To fix this, define enetc_teardown_serdes() to wrap
enetc_imdio_remove() (improve code maintenance) and call it
on bailout and remove paths.
Fixes: 975d183ef0 ("net: enetc: Initialize SerDes for SGMII and USXGMII protocols")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove casting the values returned by memory allocation function.
Coccinelle emits WARNING: casting value returned by memory allocation
unction to (struct roce_destroy_qp_req_output_params *) is useless.
This issue was detected by using the Coccinelle software.
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the patch below, the iteration through the available MMDs is
completely short-circuited, and devs_in_pkg remains set to the initial
value of zero.
Due to devs_in_pkg being zero, the rest of get_phy_c45_ids() is
short-circuited too: the following loop never reaches below this point
either (it executes "continue" for every device in package, failing to
retrieve PHY ID for any of them):
/* Now probe Device Identifiers for each device present. */
for (i = 1; i < num_ids; i++) {
if (!(devs_in_pkg & (1 << i)))
continue;
So c45_ids->device_ids remains populated with zeroes. This causes an
Aquantia AQR412 PHY (same as any C45 PHY would, in fact) to be probed by
the Generic PHY driver.
The issue seems to be a case of submitting partially committed work (and
therefore testing something other than was submitted).
The intention of the patch was to delay exiting the loop until one more
condition is reached (the devs_in_pkg read from hardware is either 0, OR
mostly f's). So fix the patch to reflect that.
Tested with traffic on a LS1028A-QDS, the PHY is now probed correctly
using the Aquantia driver. The devs_in_pkg bit field is set to
0xe000009a, and the MMDs that are present have the following IDs:
[ 5.600772] libphy: get_phy_c45_ids: device_ids[1]=0x3a1b662
[ 5.618781] libphy: get_phy_c45_ids: device_ids[3]=0x3a1b662
[ 5.630797] libphy: get_phy_c45_ids: device_ids[4]=0x3a1b662
[ 5.654535] libphy: get_phy_c45_ids: device_ids[7]=0x3a1b662
[ 5.791723] libphy: get_phy_c45_ids: device_ids[29]=0x3a1b662
[ 5.804050] libphy: get_phy_c45_ids: device_ids[30]=0x3a1b662
[ 5.816375] libphy: get_phy_c45_ids: device_ids[31]=0x0
[ 7.690237] mscc_felix 0000:00:00.5: PHY [0.5:00] driver [Aquantia AQR412] (irq=POLL)
[ 7.704739] mscc_felix 0000:00:00.5: PHY [0.5:01] driver [Aquantia AQR412] (irq=POLL)
[ 7.718918] mscc_felix 0000:00:00.5: PHY [0.5:02] driver [Aquantia AQR412] (irq=POLL)
[ 7.733044] mscc_felix 0000:00:00.5: PHY [0.5:03] driver [Aquantia AQR412] (irq=POLL)
Fixes: bba238ed03 ("net: phy: continue searching for C45 MMDs even if first returned ffff:ffff")
Reported-by: Colin King <colin.king@canonical.com>
Reported-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VSC7514 is marketed as a 10-port switch, however it has 11 physical
ports (0->10) in the block diagram:
https://www.microsemi.com/product-directory/ethernet-switches/3992-vsc7514
(also in the device tree at arch/mips/boot/dts/mscc/ocelot.dtsi)
Additionally, by architecture it has one more entry in the analyzer
block, situated right after the physical ports, for the CPU port module.
This is not a physical port, it only represents a channel for frame
injection and extraction. That entry for the CPU port is at index 11 in
the analyzer.
When the register groups for QSYS_SWITCH_PORT_MODE, SYS_PORT_MODE and
SYS_PAUSE_CFG are declared to be replicated 11 times, the 11th entry in
the array of regfields is not initialized, so the CPU port module is not
initialized either.
The documentation of QSYS_SWITCH_PORT_MODE for VSC7514 also says that
this register group is replicated 12 times, so this patch is simply
reflecting that and not introducing any further inconsistency.
Fixes: 886e1387c7 ("net: mscc: ocelot: convert QSYS_SWITCH_PORT_MODE and SYS_PORT_MODE to regfields")
Fixes: 541132f096 ("net: mscc: ocelot: convert SYS_PAUSE_CFG register access to regfield")
Reported-by: Bryan Whitehead <bryan.whitehead@microchip.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add some new interface values and update a few more descriptions.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can prevent potential incorrect DMA access attempts from the
NIC by enabling bus-master after the reset, and by disabling
bus-master earlier in cleanup.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix up our comparison to better handle a potential (but largely
unlikely) wrap around.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the host system's udev fails to set a new name for the
network port, there is no NETDEV_CHANGENAME event to trigger
the driver to send the name down to the firmware. It is safe
to set the lif name multiple times, so we add a call early on
to set the default netdev name to be sure the FW has something
to use in its internal debug logging. Then when udev gets
around to changing it we can update it to the actual name the
system will be using.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change from using hardcoded MTU limits and instead use the
firmware defined limits. The value from the LIF attributes is
the frame size, so we take off the header size to convert to
MTU size.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently drive supports taprio offload which is a tc feature offloaded
to cpsw hardware. So driver has to set the hw feature flag, NETIF_F_HW_TC
in the net device to be compliant. This patch adds the flag.
Fixes: 8127224c27 ("ethernet: ti: am65-cpsw-qos: add TAPRIO offload support")
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When regmap_update_bits failed in ave_init(), calls of the functions
reset_control_assert() and clk_disable_unprepare() were missed.
Add goto out_reset_assert to do this.
Fixes: 57878f2f46 ("net: ethernet: ave: add support for phy-mode setting of system controller")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Reviewed-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit fe80536acf ("bareudp: Added attribute to enable & disable
rx metadata collection") breaks the the original(5.7) default behavior of
bareudp module to collect RX metadadata at the receive. It was added to
avoid the crash at the kernel neighbour subsytem when packet with metadata
from bareudp is processed. But it is no more needed as the
commit 394de110a7 ("net: Added pointer check for
dst->ops->neigh_lookup in dst_neigh_lookup_skb") solves this crash.
Fixes: fe80536acf ("bareudp: Added attribute to enable & disable rx metadata collection")
Signed-off-by: Martin Varghese <martin.varghese@nokia.com>
Acked-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver is not working because of problems of its receiving code.
This patch fixes it to make it work.
When the driver receives an LAPB frame, it should first pass the frame
to the LAPB module to process. After processing, the LAPB module passes
the data (the packet) back to the driver, the driver should then add a
one-byte pseudo header and pass the data to upper layers.
The changes to the "x25_asy_bump" function and the
"x25_asy_data_indication" function are to correctly implement this
procedure.
Also, the "x25_asy_unesc" function ignores any frame that is shorter
than 3 bytes. However the shortest frames are 2-byte long. So we need
to change it to allow 2-byte frames to pass.
Cc: Eric Dumazet <edumazet@google.com>
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Reviewed-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
React to TC_SETUP_QDISC_TBF and configure the egress shaper as
appropriate with the maximum rate and burst size requested by the user.
TBF can only be offloaded on DPAA2 when it's the root qdisc, ie it's a
per port shaper.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the necessary API (dpni_set_tx_shaping) for configuring the rate and
burst size of a per port shaper in DPAA2.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the setup done for MQPRIO into a separate function so that
with the addition of another offload we do not crowd
dpaa2_eth_setup_tc(). After this restructuring it's easier to see what
is supported in terms of Qdisc offloading.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For most chip versions this has been added already. Allow also for
RTL8125A to enable ASPM.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was found that qed_pglueb_rbc_attn_handler() can produce a lot of
false-positive error detections on driver load/reload (especially after
crashes/recoveries) and spam the kernel log:
[ 4.958275] [qed_pglueb_rbc_attn_handler:324()]ICPL error - 00d00ff0
[ 2079.146764] [qed_pglueb_rbc_attn_handler:324()]ICPL error - 00d80ff0
[ 2116.374631] [qed_pglueb_rbc_attn_handler:324()]ICPL error - 00d80ff0
[ 2135.250564] [qed_pglueb_rbc_attn_handler:324()]ICPL error - 00d80ff0
[...]
Reduce the logging level of two false-positive prone error messages from
notice to verbose on initialization (only) to not mix it with real error
attentions while debugging.
Fixes: 666db4862f ("qed: Revise load sequence to avoid PCI errors")
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
