This will fix warnings like following when CONFIG_PM_SLEEP is not set:
warning: 'xxx_suspend' defined but not used [-Wunused-function]
warning: 'xxx_resume' defined but not used [-Wunused-function]
Because
SET_SYSTEM_SLEEP_PM_OPS(suspend_fn, resume_fn)
Only references the callbacks on CONFIG_PM_SLEEP (instead of CONFIG_PM).
Cc: John W. Linville <linville@tuxdriver.com>
Cc: "Rafał Miłecki" <zajec5@gmail.com>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the BT connection is initiated by headset, it's possible that headset
requests to make one A2DP and one Voice connection over the same link.
BT firmware will send a new profile A2DP_Voice in this case. So WLAN
has to take care of this new profile for tuning BTCOEX parameters.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whenever i_coff of IQ calibration is too high, AR9565 drops max
rx rate to MCS4. Skipping IQ update at this time can avoid this
problem for AR9565.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While resuming from S3, BT host issues HCI reset command and it
causes BT firmware to busy with security key calculation. At this
movement, WLAN detects MCI hardware error of MCI_CONT_INFO_TIMEOUT
and then it starts the recovery sequence repeatedly. Too many
recovery sequences would exhaust the BT kernel message pool. This
patch imposes a duration between consecutive BT recovery procedure.
Thus it solves BT firmware panic issue reported in AR9565.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TXIQ and RXIQ share the same data path to upload the measurement
result, we should turn off RXIQ calibration while re-calibrating radio
Signed-off-by: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Self generated MCI messages is configured to use chain 1. As
ar9565 is 1x1 solution, It can not use Chain 1. Hence fix
Chain 1 for ar9462 alone. Not doing so, could affect WLAN
connectivity in ar9565 as LNA sharing is not informed by BT.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The simulataneous transmission of both WLAN and BT might cause
increase in power levels. To avoid regulatory violation, WLAN tx
power will be adjusted according to BT power index based on avaliability
of BT scheduling messages. WLAN tx power reduction might affect its
performance. So WLAN tx power is only be lowered when the signal strength
is good enough. Otherwise concurrent tx will be disabled and WLAN uses
it default power levels. Also concurrent tx is disabled whenever WLAN is
moving to off-channel which might be used by BT.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is useful to have channel mode in caldata to find out
whether operaing channel is in HT40/20 when we are currently
on offchannel. It will be used by BTCOEX to enable/disable
concurrent tx mechanism later.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This feature enables both WLAN and BT can transmit simultaneously
by setting WLAN and BT to equal priorities. Whenever both are
transmitting, it might violate regulatory power limits. To avoid
regulatory violation, WLAN tx power will be adjusted according to BT
power index based on avaliability of BT scheduling message. If the
combined power exceeds threshold, BT transmission will be held off.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
WLAN updates channel bitmap when associated and disassociated. Channel
bitmap will reflect whare are the channels used or affected by WLAN and
BT should avoid using those. Not doing so, could affect BT traffic
as both WLAN and BT is operating on same channel.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently ath9k need to have beacon interval matched
between STA mode and beaconing mode. Advertize this
through interface combinations.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Once the driver advertizes interface combination logic
based on its firmware/hardware limitation, cfg80211
takes care of all the necessary logic such as maximum
beaconing vifs, standlone interface etc.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will allow us to create virtual interface the driver supports.
Also this ensures multivif support and limitation advertised
by the driver is taken care in cfg80211 itself.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When WLAN is idle ensure we downgrade to FTP_STOMP_LOW weight
(from STOMP_LOW) to provide more bandwidth for BT FTP profile.
WLAN's idleness can be estimated by taking into account of the
rx data packets and just ignore beacons, qos nullfunc etc.
Also update bt_wait_time even if the chip is in NETWORK SLEEP
mode. This should help BT throughput when WLAN is idle.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Several people have complained about an unusual
and undocumented feature of the AR9170 hardware:
In siffer mode, the hardware generates spurious
ACK frames for every received frame... even
broadcasts.
The reason for this malfunction is unknown:
<http://marc.info/?l=linux-wireless&m=134517238506033>
But there's a workaround: Instead of the special
sniffer mode, the hardware will be put into
station mode and all rx filters are disabled.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Marco Fonseca <marco@tampabay.rr.com>
Reported-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With this one we have:
- pn544 p2p support.
- pn544 physical and HCI layers separation. We are getting the pn544 driver
ready to support non i2c physical layers.
- LLCP SNL (Service Name Lookup). This is the NFC p2p service discovery
protocol.
- LLCP datagram sockets (connection less) support.
- IDR library usage for NFC devices indexes assignement.
- NFC netlink extension for setting and getting LLCP link characteristics.
- Various code style fixes and cleanups spread over the pn533, LLCP, HCI and
pn544 code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=OC0R
-----END PGP SIGNATURE-----
Merge tag 'nfc-next-3.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-3.0
This is the first NFC pull request for 3.8
With this one we have:
- pn544 p2p support.
- pn544 physical and HCI layers separation. We are getting the pn544 driver
ready to support non i2c physical layers.
- LLCP SNL (Service Name Lookup). This is the NFC p2p service discovery
protocol.
- LLCP datagram sockets (connection less) support.
- IDR library usage for NFC devices indexes assignement.
- NFC netlink extension for setting and getting LLCP link characteristics.
- Various code style fixes and cleanups spread over the pn533, LLCP, HCI and
pn544 code.
NFC_CMD_LLC_GET_PARAMS: request LTO, RW, and MIUX parameters for a device
NFC_CMD_LLC_SET_PARAMS: set one or more of LTO, RW, and MIUX parameters for
a device. LTO must be set before the link is up otherwise -EINPROGRESS is
returned. RW and MIUX can be set at anytime and will be passed in subsequent
CONNECT and CC messages. If one of the passed parameters is wrong none is
set and -EINVAL is returned.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The Tx queues are no longer valid when we receive a disconnection or when
the LLCP link goes down. In the later case we also purge the entire local
Tx queue.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This config item has not carried much meaning for a while now and is
almost always enabled by default. As agreed during the Linux kernel
summit, remove it.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This config item has not carried much meaning for a while now and is
almost always enabled by default. As agreed during the Linux kernel
summit, remove it.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This config item has not carried much meaning for a while now and is
almost always enabled by default. As agreed during the Linux kernel
summit, remove it.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
As a consequence the NFC device IDs won't be increasing all the time,
as IDR provides the first available ID.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Get rid of unused arg param in pn533_init_target_complete and
in pn533_start_poll_complete.
Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Max frame size should be 264 bytes as per spec and not limited to
endpoint MaxPacketSize which is 64 in my case (acr122 reader).
Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
It simply involves getting the client dsap and ssap and calling the UI
frame building and sending routine.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
UI frames still need to follow the MIU rule, and they need to use the
client passed dsap as the listening socket dsap is stuck on SDP.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When DEP goes down, bound cl sockets can be kept alive as there is no
reason to kill a connection less server socket because the LLCP link
went down.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Replying to an SNL (Service Name Lookup) means that the other end of
the link can now rely on our answer (Which is an ssap) and thus we have
to reserve it.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Logical continuations should be on the previous line.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Return code from nfc_hci_execute_cmd was not propagated to caller.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Check for error and return if any. This makes it easier to see what is
a 'positive' function flow.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
There is no need for return statement at the end of function returning
void.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
No need for local rc variable as result of nci_request can be returned
directly.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
local_gb is of size NFC_MAX_GT_LEN and len is used as index for it.
Check len against this instead of NCI_MAX_PARAM_LEN before accessing
local_gb.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This is useful when getting devices to know if they're in target or
initiator mode.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
rf_mode is now set to NFC_RF_NONE when a device gets allocated,
when the link goes down, and when stop polling.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
SNL (Service Name Lookup) allows for LLCP peers to map service names with
SAPs. This is mandatory for connection less support as peers need to get
the right SAPs without sending the CONNECT frame.
Here we only support the Rx part of SNL. The Tx one will be implemented
when supporting connection less LLCP sockets.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
