Make instance->adprecovery variable atomic and removes hba_lock spinlock
while accessing instance->adprecovery.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
1. For iMR controllers, firmware will report two queue depths:
- Controller-wide queue depth
- LDIO queue depth (240)
Controller-wide queue depth will be greater among the two. Using this
new feature, iMR can provide larger Queue depth(QD) for JBOD and limited
QD for Virtual Disk(VD).
2. megaraid_sas driver will throttle read/write LDIOs based on "LDIO
Queue Depth".
3. Dual queue depth can be enabled/disabled via module parameter. It is
enabled by default if the firmware supports it. Only specific firmware
builds will enable the feature.
4. Added sysfs parameter "ldio_outstanding" which permits querying the
number of outstanding LDIO requests at runtime.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
build_and_issue_cmd should return SCSI_MLQUEUE_HOST_BUSY for a few error
cases instead of returning 1.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch will create a reply queue pool for each MSI-X index and will
provide an array of base addresses instead of the single address of
legacy mode. Using this new interface the driver can support higher
queue depths through scattered DMA pools.
If array mode is not supported driver will fall back to the legacy
method of reply pool allocation. This limits controller queue depth to
1K max. To enable a queue depth of more than 1K driver requires firmware
to support array mode and scratch_pad3 will provide the new queue depth
value.
When RDPQ is used, downgrading to an older firmware release should not
be permitted. This may cause firmware fault and is not supported.
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch will update device Queue depth based on interface type(SAS,
SATA..) for sysPDs. For Virtual disks(VDs), there will be no change in
queue depth (will remain 256). To fetch interface type (SAS or SATA or
FC..) of syspD, driver will send DCMD MR_DCMD_PD_GET_INFO.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds task management for SCSI commands. Added functions are
task abort and target reset.
1. Currently, megaraid_sas driver performs controller reset when any IO
times out. With task management support added, task abort and target
reset will be tried to recover timed out IO. If task management fails,
then controller reset will be performaned. If the task management
request times out, fail the request and escalate to the next
level (controller reset).
2. mr_device_priv_data will be allocated for all generations of
controller, but is_tm_capable flag will never be set for
controllers (prior to Invader series) as firmware support is not
available for task management.
3. Task management capable firmware will set is_tm_capable flag in
firmware API.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch will do proper error handling for DCMD timeout failure cases
for Fusion adapters:
1. For MFI adapters, in case of DCMD timeout (DCMD which must return
SUCCESS) driver will call kill adapter.
2. What action needs to be taken in case of DCMD timeout is decided by
function dcmd_timeout_ocr_possible(). DCMD timeout causing OCR is
applicable to the following commands:
MR_DCMD_PD_LIST_QUERY
MR_DCMD_LD_GET_LIST
MR_DCMD_LD_LIST_QUERY
MR_DCMD_CTRL_SET_CRASH_DUMP_PARAMS
MR_DCMD_SYSTEM_PD_MAP_GET_INFO
MR_DCMD_LD_MAP_GET_INFO
3. If DCMD fails from driver init path there are certain DCMDs which
must return SUCCESS. If those DCMDs fail, driver bails out. For optional
DCMDs like pd_info etc., driver continues without executing certain
functionality.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch will do synhronization between OCR function and AEN function
using "reset_mutex" lock. reset_mutex will be acquired only in the
first half of the AEN function which issues a DCMD. Second half of the
function which calls SCSI API (scsi_add_device/scsi_remove_device)
should be out of reset_mutex to avoid deadlock between scsi_eh thread
and driver.
During chip reset (inside OCR function), there should not be any PCI
access and AEN function (which is called in delayed context) may be
firing DCMDs (doing PCI writes) when chip reset is happening in parallel
which will cause FW fault. This patch will solve the problem by making
AEN thread and OCR thread mutually exclusive.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch changes the !blk-mq path to the same defaults as the blk-mq
I/O path by always enabling block tagging, and always using host wide
tags. We've had blk-mq available for a few releases so bugs with
this mode should have been ironed out, and this ensures we get better
coverage of over tagging setup over different configs.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
The DELL PERC5 controller firmware does not list tape drives in response
to MR_DCMD_PD_LIST_QUERY. This causes tape drives not be exposed to the
OS when connected to a PERC5 controller.
This patch permits detection of tape drives connected to a PERC5
controller by exposing non-TYPE_DISK devices unconditionally.
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is an issue on SMAP enabled CPUs and 32 bit apps running on 64 bit
OS. Do not access user memory from kernel code. The SMAP bit restricts
accessing user memory from kernel code.
Cc: <stable@vger.kernel.org>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It may happen (kdump), that an interrupt is invoked just after the
setup_irqs function was called but before the tasklet was initialised.
At this phase the hw ints should have been disabled, but for unknown
reason this mechanism seems to not work properly.
From: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Do not use PAGE_SIZE marco to calculate max_sectors per I/O
request. Driver code assumes PAGE_SIZE will be always 4096 which can
lead to wrongly calculated value if PAGE_SIZE is not 4096. This issue
was reported in Ubuntu Bugzilla Bug #1475166.
Cc: <stable@vger.kernel.org>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove PCI id based checks and use instance->ctrl_context to decide
whether controller is MFI-based or a Fusion adapter. Additionally,
Fusion adapters are divided into two categories: Thunderbolt and
Invader.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some of these code changes were proposed by David Binderman.
Removed redudant check of requestorId. Redundant condition:
instance.requestorId. Check for plasma firmware 1.11 are now
restructured to support only specific device id.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Print firmware events in human-readable form. This will help users track
any critical firmware events without special application support.
Sample syslogd output:
megaraid_sas 0000:02:00.0: 8619 (491648347s/0x0020/WARN) - Controller temperature threshold exceeded. This may indicate inadequate system cooling. Switching to low performance mode.
The format of logged events is:
"<pci_dev_id>: <sequence_number> (<timestamp>/<locale>/<class>) - <description>"
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Implemented JBOD map which will provide quick access for JBOD path and
also provide sequence number. This will help hardware to fail command
to the FW in case of any sequence mismatch.
Fast Path I/O for JBOD will refer JBOD map (which has sequence number
per JBOD device) instead of RAID map. Previously, the driver used RAID
map to get device handle for fast path I/O and this not have sequence
number information. Now, driver will use JBOD map instead. As part of
error handling, if JBOD map is failed/not supported by firmware, driver
will continue using legacy behavior.
Now there will be three IO paths for JBOD (syspd):
- JBOD map with sequence number (Fast Path)
- RAID map without sequence number (Fast Path)
- FW path via h/w exception queue deliberately setup devhandle
0xFFFF (FW path).
Relevant data structures:
- Driver send new DCMD MR_DCMD_SYSTEM_PD_MAP_GET_INFO for this purpose.
- struct MR_PD_CFG_SEQ- This structure represent map of single physical
device.
- struct MR_PD_CFG_SEQ_NUM_SYNC- This structure represent whole JBOD
map in general(size, count of sysPDs configured, struct MR_PD_CFG_SEQ
of syspD with 0 index).
- JBOD sequence map size is: sizeof(struct MR_PD_CFG_SEQ_NUM_SYNC)
+ (sizeof(struct MR_PD_CFG_SEQ) * (MAX_PHYSICAL_DEVICES - 1)) which
is allocated while setting up JBOD map at driver load time.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Martin Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use dev_printk() when possible to make messages more useful.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
This is the usual grab bag of driver updates (lpfc, hpsa,
megaraid_sas, cxgbi, be2iscsi) plus an assortment of minor updates.
There are also one new driver: the Cisco snic; the advansys driver has
been rewritten to get rid of the warning about converting it to the
DMA API, the tape statistics patch got in and finally, there's a
resuffle of SCSI header files to separate more cleanly initiator from
target mode (and better share the common definitions).
Signed-off-by: James Bottomley <JBottomley@Odin.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJViKWdAAoJEDeqqVYsXL0MAr8IAMmlA6HBVjMJJFCEOY9corHj
e70MNQa7LUgf+JCdOtzGcvHXTiFFd4IHZAwXUJAnsC4IU2QWEfi1bjUTErlqBIGk
LoZlXXpEHnFpmWot3OluOzzcGcxede8rVgPiKWVVdojIngBC2+LL/i2vPCJ84ri9
WCVlk6KBvWZXuU6JuOKAb2FO9HOX7Q61wuKAMast2Qc6RNc2ksgc7VbstsITqzZ9
FVEsjmQ5lqUj+xdxBpiUOdUpc22IJ4VcpBgQ2HrThvg6vf4aq937RJ/g4vi/g0SU
Utk0a3bUw1H/WnYAfJVFx83nVEsS/954Z7/ERDg1sjlfLYwQtQnpov0XIbPIbZU=
=k9IT
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is the usual grab bag of driver updates (lpfc, hpsa,
megaraid_sas, cxgbi, be2iscsi) plus an assortment of minor updates.
There is also one new driver: the Cisco snic. The advansys driver has
been rewritten to get rid of the warning about converting it to the
DMA API, the tape statistics patch got in and finally, there's a
resuffle of SCSI header files to separate more cleanly initiator from
target mode (and better share the common definitions)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (156 commits)
snic: driver for Cisco SCSI HBA
qla2xxx: Fix indentation
qla2xxx: Comment out unreachable code
fusion: remove dead MTRR code
advansys: fix compilation errors and warnings when CONFIG_PCI is not set
mptsas: fix depth param in scsi_track_queue_full
megaraid: fix irq setup process regression
lpfc: Update version to 10.7.0.0 for upstream patch set.
lpfc: Fix to drop PLOGIs from fabric node till LOGO processing completes
lpfc: Fix scsi task management error message.
lpfc: Fix cq_id masking problem.
lpfc: Fix scsi prep dma buf error.
lpfc: Add support for using block multi-queue
lpfc: Devices are not discovered during takeaway/giveback testing
lpfc: Fix vport deletion failure.
lpfc: Check for active portpeerbeacon.
lpfc: Update driver version for upstream patch set 10.6.0.1.
lpfc: Change buffer pool empty message to miscellaneous category
lpfc: Fix incorrect log message reported for empty FCF record.
lpfc: Fix rport leak.
...
This fixes a regression caused by commit
d3557fc8be megaraid_sas : Add separate function
for setting up IRQs This makes boot end with 'root does not exist' message on
certain adapters.
The bug is that the driver does not setup ints for cards without msi-x
support. This patch fixes it, in addition to that it moves tasklet
initialisation before enable_intr, otherwise a kernel panic may occur, when an
interrupt arrives before the tasklet is ready.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
This patch is rebased on top of recently sent 18 patches(submitted by me) for
megaraid_sas driver.
Change the return value of wait_and_poll() and megsas_issue_blocked_cmd()
based on MFI_STAT returned by firmware for that command. Earlier driver always
send return type based on command completion (but never check MFI_STAT_OK for
that command), so even if command is failed by firmware still driver will
return SUCCESS status from these functions wait_and_poll() and
megsas_issue_blocked_cmd() and if caller of these functions does not check
command status (MFI_STAT), then it may endup using invalid data returned in
DMA buffers(one of the example is megasas_ld_list_query DCMD). Best thing to
avoid this type of issue is do error handling and set proper return type from
caller function wait_and_poll() and megsas_issue_blocked_cmd().
The change proposed in this patch will fix the regression introduced in patch-
"90dc9d9 megaraid_sas : MFI MPT linked list corruption fix" inside function
megasas_ld_list_query(). Prior to this MFI MPT linked list corruption fix
patch, megasas_ld_list_query() function used to check DCMD status(returned by
firmware) but with this linked list corruption fix patch, DCMD status will not
be checked inside function megasas_ld_list_query() and introduced this issue
of wrong data being used by function megasas_ld_list_query().
Cc: <stable@vger.kernel.org>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Swap the whole 32 bits we read from the hardware instead of swapping
just the 16bits we care about in place later.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Converting structure fields in place is always a bad idea, and in this case
by moving it into the only caller we also only have to do a single byte
swap as most fields of this structure are never used.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Add noop conversions for all ones to make sparse happy.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
This adds endianness annotations to all data structures, and a few
variables directly referencing them.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
drivers/scsi/megaraid/megaraid_sas_base.c:1701:6: sparse: symbol 'megasas_complete_outstanding_ioctls' was not declared. Should it be static?
From: Christoph Hellwig <hch@lst.de>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
This patch will add support for Single Server High Availability(SSHA) cluster
support. Here is the short decsription of changes done to add support for
SSHA-
1) Host will send system's Unique ID based on DMI_PRODUCT_UUID to firmware.
2) Toggle the devhandle in LDIO path for Remote LDs.
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
This patch will upgrade the driver version and add back the release date and
sysfs hook for the same. Some internal applications uses sysfs parameter for
release date, so they were broken because of removal of release date from
sysfs.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
megaraid_sas driver will use block layer provided tag for indexing internal
MPT frames to get any unique MPT frame tied with tag. Each IO request
submitted from SCSI mid layer will get associated MPT frame from MPT framepool
(retrieved and return back using spinlock inside megaraid_sas driver's
submission/completion call back). Getting MPT frame from MPT Frame pool is
very expensive operation because of associated spin lock operation (spinlock
overhead increase on multi NUMA node). This type of locking in driver is very
expensive call considering each IO request need - Acquire and Release of the
same lock.
With this support, in IO path driver will directly provide the unique command
index(which is based on block layer tag) and will get the MPT frame tied to
the tag and this way driver can get rid off lock, which synchronizes the
access to MPT frame pool while fetching and returning MPT frame from the pool.
This support in driver provides siginificant performance improvement(on multi
NUMA node system)on latest upstream with SCSI.MQ as well as on existing linux
distributions.
Here is the data for test executed at Avago-
- IO Tool- FIO
- 4 Socket SMC server. (4 NUMA node server)
- 12 SSDs in JBOD mode .
- 4K Rand READ, QD=32
- SCSI MQ x86_64 (Latest Upstream kernel)
- upto 300% Performance Improvement.
If IOs are running on single Node, perfromance gain is less, but as soon as
increase number of nodes, performance improvement is significant. IOs running
on all 4 NUMA nodes, with this patch applied IOPs observed was 1170K vs 344K
IOPs seen without this patch.
Logically, there are two parts of this patch- 1) Block layer tag support 2)
changes in calling convention of return_cmd. part 2 will revert the changes
done by patch- 90dc9d9 megaraid_sas : MFI MPT linked list corruption fix
because changes done in part 1 has fixed the problem of MFI MPT linked list
corruption. part 2 is very much dependent on part 1, so we decided to have
single patch for these two logical changes.
[jejb: remove chatty printk pointed out by hch]
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
This patch will create separate functions for- 1) setting up IRQs for MSI-x
interrupts 2) setting up IRQs for legacy interrupts 3) freeing up IRQs. and
enable interrupts after adapter's initialization. The reason behind
initialising adapter earlier is: by that time firmware is operational and can
send interrupts, so better to use interrupt based interface to send internal
DCMD to firmware instead of using polling method, since MFI frames' pool size
is reduced and polling method does not free up MFI frame for fusion adapters,
so sending more DCMDs with polled method may cause MFI frames's pool go out of
frames and end up failing DCMD.
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
struct fusion_context *fusion is already memset to '0', so remove a
redundant call to memmset "fusion->load_balance_info" to '0'.
Signed-off-by: Chaitra Basappa <chaitra.basappa@avagotech.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
1) For fusion adapters, limit reserved frames for non SCSI commands to 8
(3 for parallel IOCTLs + 5 for driver's internal DCMDs).
Earlier reserved commands for non SCSI IO frames was set to 32, so with
this implementation, increased per controller "can_queue".
Behavior of MFI controllers will remain unchanged.
2) Optimize the code related to per controller's 'can_queue' setting.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Chaitra Basappa <chaitra.basappa@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
