The calculation of SPR and SPPR doesn't round correctly at several
places which might result in baud rates that are too big. For example
with tclk_hz = 250000001 and target rate 25000000 it determined a
divider of 10 which is wrong.
Instead of fixing all the corner cases replace the calculation by an
algorithm without a loop which should even be quicker to execute apart
from being correct.
Fixes: df59fa7f4b ("spi: orion: support armada extended baud rates")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
A null dereference or Oops exception might occurs when reading at once the
whole content of an spi-nor of big enough size that requires an scatterlist
table that does not fit into one single page.
The spi_map_buf function is ignoring the chained sg case by dereferenceing
the scatterlist elements in an array fashion. This wrongly assumes that
the allocation of the scatterlist elements are contiguous. This is true as
long as the scatterlist table fits within a PAGE_SIZE. However, for
allocation where the scatter table is bigger than that, the pages allocated
by sg_alloc might not be contigous.
The sg table can be properly walked by sg_next instead of using an array.
Signed-off-by: Juan Gutierrez <juan.gutierrez@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A call to clk_get_rate appears to be called in the context of an interrupt,
cache the bus clock for the frequency calculations in transmission.
This fixes a 'BUG: scheduling while atomic' and
'WARNING: CPU: 0 PID: 777 at kernel/sched/core.c:2960 atmel_spi_unlock'
Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Steve deRosier <steve.derosier@lairdtech.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the managed gpio CS pin request so that we avoid having trouble
in the cleanup code.
In fact, if module was configured with DT, cleanup code released
invalid pin. Since resource wasn't freed, module cannot be reinserted.
This require to extract the gpio request call from the "setup" function
and call it in the appropriate probe function.
Reported-by: Alexander Morozov <linux@meltdown.ru>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Once dspi is used in uboot, the SPI_SR have been set by some value.
At this time, if kernel enable the interrupt before clear the
status flag, that will trigger the wrong interrupt.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When we get a spurious interrupt in fsl_espi_irq, we end up
processing four uninitalized bytes of data, as shown in this
warning message:
drivers/spi/spi-fsl-espi.c: In function 'fsl_espi_irq':
drivers/spi/spi-fsl-espi.c:462:4: warning: 'rx_data' may be used uninitialized in this function [-Wmaybe-uninitialized]
This adds another check so we skip the data in this case.
Fixes: 6319a68011 ("spi/fsl-espi: avoid infinite loops on fsl_espi_cpu_irq()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Instantiated SPI device nodes are marked with OF_POPULATE. This was
introduced in bd6c164. On unloading, loaded device nodes will of course
be unmarked. The problem are nodes that fail during initialisation: If a
node fails, it won't be unloaded and hence not be unmarked.
If a SPI driver module is unloaded and reloaded, it will skip nodes that
failed before.
Skip device nodes that are already populated and mark them only in case
of success.
Note that the same issue exists for I2C.
Fixes: bd6c164 ("spi: Mark instantiated device nodes with OF_POPULATE")
Signed-off-by: Ralf Ramsauer <ralf@ramses-pyramidenbau.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Some SPI masters require slave selection before the transfer
can begin [1]. The SPI framework currently selects the chip using
either 1) the internal CS mechanism or 2) the GPIO CS, but not both.
This patch adds a new master->flags define to indicate both the GPIO
CS and the internal chip select mechanism should be used.
Tested On:
Altera CycloneV development kit
Compile tested for build errors on x86_64 (allyesconfigs)
[1] DesignWare dw_apb_ssi Databook, Version 3.20a (page 39)
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A good practice is to prefix the names of functions by the name
of the subsystem.
The kthread worker API is a mix of classic kthreads and workqueues. Each
worker has a dedicated kthread. It runs a generic function that process
queued works. It is implemented as part of the kthread subsystem.
This patch renames the existing kthread worker API to use
the corresponding name from the workqueues API prefixed by
kthread_:
__init_kthread_worker() -> __kthread_init_worker()
init_kthread_worker() -> kthread_init_worker()
init_kthread_work() -> kthread_init_work()
insert_kthread_work() -> kthread_insert_work()
queue_kthread_work() -> kthread_queue_work()
flush_kthread_work() -> kthread_flush_work()
flush_kthread_worker() -> kthread_flush_worker()
Note that the names of DEFINE_KTHREAD_WORK*() macros stay
as they are. It is common that the "DEFINE_" prefix has
precedence over the subsystem names.
Note that INIT() macros and init() functions use different
naming scheme. There is no good solution. There are several
reasons for this solution:
+ "init" in the function names stands for the verb "initialize"
aka "initialize worker". While "INIT" in the macro names
stands for the noun "INITIALIZER" aka "worker initializer".
+ INIT() macros are used only in DEFINE() macros
+ init() functions are used close to the other kthread()
functions. It looks much better if all the functions
use the same scheme.
+ There will be also kthread_destroy_worker() that will
be used close to kthread_cancel_work(). It is related
to the init() function. Again it looks better if all
functions use the same naming scheme.
+ there are several precedents for such init() function
names, e.g. amd_iommu_init_device(), free_area_init_node(),
jump_label_init_type(), regmap_init_mmio_clk(),
+ It is not an argument but it was inconsistent even before.
[arnd@arndb.de: fix linux-next merge conflict]
Link: http://lkml.kernel.org/r/20160908135724.1311726-1-arnd@arndb.de
Link: http://lkml.kernel.org/r/1470754545-17632-3-git-send-email-pmladek@suse.com
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Borislav Petkov <bp@suse.de>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To avoid warning when using i2c gpio expander change call to the
cansleep variant. There should be no issue with sleeping in the
drivers probe function.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Mark Brown <broonie@kernel.org>
Kbuild test robot reports:
drivers/spi/spi-pxa2xx.c: In function ‘setup_cs’:
drivers/spi/spi-pxa2xx.c:1190:20: error: implicit declaration of function ‘desc_to_gpio’
...
Reason for this is the fact that those functions are declared in
linux/gpio/consumer.h which is not included in the driver. Fix this by
including it.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix to return error code -EINVAL if no CS GPIOs available
instead of 0, as done elsewhere in this function.
Fixes: f13d4e189d ("spi: imx: Gracefully handle NULL master->cs_gpios")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver uses custom chip_info coming from platform data for chip selects
implemented as GPIOs. If the system lacks board files setting up the
platform data, it is not possible to use GPIOs as chip selects.
This adds support for GPIO descriptors so that regardless of the underlying
firmware interface (DT, ACPI or platform data) the driver can request GPIOs
used as chip selects and configure them accordingly.
The custom chip_info GPIO support is still left there to make sure the
existing systems keep working as expected.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is possible that master->cs_gpios is NULL after spi_bitbang_start(),
this happens if the master has no CS GPIOs specified in DT. Check for
this case after spi_bitbang_start() to prevent NULL pointer dereference
in the subsequent for loop, which accesses the master->cs_gpios field.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Martin Kaiser <martin@kaiser.cx>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This spi driver uses the common spi-bcm-qspi driver and implements iProc
SoCs specific interrupt controller. The common driver now calls the SoC
handlers when present. Adding support for both muxed l1 and unmuxed interrupt
sources.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The return value of fsl_espi_probe (currently struct spi_master *)
is just used for checking whether an error occurred.
Change the return value type to int and simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: fa236a7ef2 ("spi: bcm-qspi: Add Broadcom MSPI driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In case of error, the function kcalloc() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
Fixes: fa236a7ef2 ("spi: bcm-qspi: Add Broadcom MSPI driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The two power management functions are define inside of an #ifdef
but referenced unconditionally, which is obviously broken when
CONFIG_PM_SLEEP is not set:
drivers/spi/spi-bcm-qspi.c:1300:13: error: 'bcm_qspi_suspend' undeclared here (not in a function)
drivers/spi/spi-bcm-qspi.c:1301:13: error: 'bcm_qspi_resume' undeclared here (not in a function)
This replaces the #ifdef with a __maybe_unused annotation that lets
the compiler figure out whether to drop the functions itself,
and uses SIMPLE_DEV_PM_OPS() to refer to the functions.
This will also fill the freeze/thaw/poweroff/restore callback
pointers in addition to suspend/resume, but as far as I can tell,
this is what we want.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: fa236a7ef2 ("spi: bcm-qspi: Add Broadcom MSPI driver")
Signed-off-by: Mark Brown <broonie@kernel.org>
The header isn't actually needed here, but including it leads
to a build warning when CONFIG_MTD is disabled:
include/linux/mtd/cfi.h:76:2: #warning No CONFIG_MTD_CFI_Ix selected. No NOR chip support can work. [-Werror=cpp]
Fixes: fa236a7ef2 (spi: bcm-qspi: Add Broadcom MSPI driver)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add definition of further register bits for use in upcoming
driver extensions and improve current bit definitions:
- use BIT macro
- use bit names as in the chip spec
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Change register access to the method used in other drivers too.
- use register names as in the chip spec for constants
- avoid hard to read statements like
__be32 __iomem *espi_mode = ®_base->mode
- get rid of old powerpc-specific functions like in_8
In addition annotate reg_base in struct mpc8xxx_spi as __iomem.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify the interrupt handler a little. In addition don't call
fsl_espi_cpu_irq() if no event bit is set.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If t is not null then the SPI core takes care that bits_per_word and
speed_hz are populated. This allows to simplify fsl_espi_setup_transfer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
imx35 and compatible chipsets support loopback mode by setting a
loopback control bit in the test register. Make this setting available
for data transfers, similar to what we do for imx51.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Mark Brown <broonie@kernel.org>
Modify spi_imx_clkdiv_2() to return the resulting bus clock frequency
when the selected clock divider is applied. Set spi_imx->spi_bus_clk to
this frequency.
If spi_bus_clk is unset, spi_imx_calculate_timeout() causes a
division by 0.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Mark Brown <broonie@kernel.org>
This change implements BSPI driver for Broadcom BRCMSTB, NS2,
NSP SoCs works in combination with the MSPI controller driver
and implements flash read acceleration and implements the
spi_flash_read() method. Both MSPI and BSPI controllers are
needed to access spi-nor flash.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adding the settop SoC platfrom driver, this driver is compatible
with the settop MSPI+BSPI and MSPI only blocks implemented on the
SoCs. Driver calls the spi-bcm-qspi probe(), remove() and pm_ops.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Master SPI driver for Broadcom settop, iProc SoCs. The driver
is used for devices that use SPI protocol on BRCMSTB, NSP, NS2
SoCs. SoC platform driver call exported porbe(), remove()
and suspend/resume pm_ops implemented in this common driver.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Yendapally Reddy Dhananjaya Reddy
Signed-off-by: Mark Brown <broonie@kernel.org>
devm_* API is supposed to be used only in probe function call.
The resource is allocated at 'probe' and free automatically at 'remove'.
Usage of devm_* functions outside probe sometimes leads to resource leak.
Thus avoid using devm_* APIs in .setup/.cleanup callbacks.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge both functions to reduce source code size and improve
readability.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move checking for a zero-length message up in the call chain and
use m->frame_length instead of re-calculating the overall length
of all transfers in the message.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Factor out copying read data to the read buffers in the original
message to a new function fsl_espi_copy_from_buf.
This also allows to simplify fsl_espi_copy_to_buf.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Better structure the code by population all elements of struct
spi_transfer in one place.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Checking the message is currently done at diffrent places in the
driver. Factor it out to fsl_espi_check_message.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Most of the devices in the supported list have PXA configuration of FIFO. In
particularly Intel Medfield and Merrifield have bigger FIFO, than it's defined
for CE4100.
Split CE4100 in the similar way how it was done for Intel Quark, i.e. prefix
definitions by CE4100 and append necessary pieces of code to switch case
conditions.
We are on safe side since those bits are ignored on all LPSS IPs.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Transfer state machine in this driver does not need to set/unset pointer
to chip data between queueing and finalizing message as it is not
actually used as a state info itself but just pointer passing.
Since this per SPI device specific chip data is already carried in
ctldata use that and remove pointer to chip data from driver data.
While at it, group initialized variables before uninitialized variables
in pump_transfers().
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
