Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
While the state is updated when the error counters increase and
decrease, there is no event when the bus recovers and the error counters
decrease again. So add that event as well.
Change the state going downward to be ERROR_PASSIVE -> ERROR_WARNING ->
ERROR_ACTIVE instead of directly to ERROR_ACTIVE again.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Acked-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Tested-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When the CAN interface is closed it the hardwre is put in power down
mode, but does not reset the error counters / state. Reset the D_CAN on
open, so the reported state and the actual state match.
According to [1], the C_CAN module doesn't have the software reset.
[1] http://www.bosch-semiconductors.com/media/ip_modules/pdf_2/c_can_fd8/users_manual_c_can_fd8_r210_1.pdf
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When the status register is read without the status IRQ pending, the
chip may not raise the interrupt line for an upcoming status interrupt
and the driver may miss a status interrupt.
It is critical that the BUSOFF status interrupt is forwarded to the
higher layers, since no more interrupts will follow without
intervention.
Thanks to Wolfgang and Joe for bringing up the first idea.
Signed-off-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Joe Burmeister <joe.burmeister@devtank.co.uk>
Fixes: fa39b54ccf ("can: c_can: Get rid of pointless interrupts")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make c_can_pci_data structures const as they are only used during
a copy operation.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The D_CAN controller doesn't provide a triple sampling mode, so don't set
the CAN_CTRLMODE_3_SAMPLES flag in ctrlmode_supported. Currently enabling
triple sampling is a no-op.
Signed-off-by: Richard Schütz <rschuetz@uni-koblenz.de>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.6
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
platform_device_id are not supposed to change at runtime. All functions
working with platform_device_id provided by <linux/platform_device.h>
work with const platform_device_id. So mark the non-const structs as
const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_complete_done() allows to opt-in for gro_flush_timeout,
added back in linux-3.19, commit 3b47d30396
("net: gro: add a per device gro flush timer")
This allows for more efficient GRO aggregation without
sacrifying latencies.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The priv->device pointer for c_can_pci is never set, but it is used
without a NULL check in c_can_start(). Setting it in c_can_pci_probe()
like c_can_plat_probe() prevents c_can_pci.ko from crashing, with and
without CONFIG_PM.
This might also cause the pm_runtime_*() functions in c_can.c to
actually be executed for c_can_pci devices - they are the only other
place where priv->device is used, but they all contain a null check.
Signed-off-by: Einar Jón <tolvupostur@gmail.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When testing CAN write floods on Altera's CycloneV, the first 2 bytes
are sometimes 0x00, 0x00 or corrupted instead of the values sent. Also
observed bytes 4 & 5 were corrupted in some cases.
The D_CAN Data registers are 32 bits and changing from 16 bit writes to
32 bit writes fixes the problem.
Testing performed on Altera CycloneV (D_CAN). Requesting tests on other
C_CAN & D_CAN platforms.
Reported-by: Richard Andrysek <richard.andrysek@gomtec.de>
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The assignment 'cf->data[2] |= CAN_ERR_PROT_UNSPEC' used at CAN error message
creation time is obsolete as CAN_ERR_PROT_UNSPEC is zero and cf->data[2] is
initialized with zero in alloc_can_err_skb() anyway.
So we could either assign 'cf->data[2] = CAN_ERR_PROT_UNSPEC' correctly or we
can remove the obsolete OR operation entirely.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
As Dan Carpenter reported in http://marc.info/?l=linux-can&m=144793696016187
the assignment of the error location in CAN error messages had some bit wise
overlaps. Indeed the value to be assigned in data[3] is no bitfield but defines
a single value which points to a location inside the CAN frame on the wire.
This patch fixes the assignments for the error locations in error messages.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The previous change 3973c526ae (net: can: c_can: Disable pins when CAN
interface is down) causes a slight glitch on the pinctrl settings when used.
Since commit ab78029 (drivers/pinctrl: grab default handles from device core),
the device core will automatically set the default pins. This causes the pins
to be momentarily set to the default and then to the sleep state in
register_c_can_dev(). By adding an optional "enable" state, boards can set the
default pin state to be disabled and avoid the glitch when the switch from
default to sleep first occurs. If the "enable" state is not available
c_can_pinctrl_select_state() falls back to using the "default" pinctrl state.
[Roger Q] - Forward port to v4.2 and use pinctrl_get_select().
Signed-off-by: J.D. Schroeder <jay.schroeder@garmin.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Conflicts:
arch/arm/boot/dts/imx6sx-sdb.dts
net/sched/cls_bpf.c
Two simple sets of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Put controller into init mode in network stop to end pending transmissions. The
issue is observed in cases when transmitted frame is not acked.
Signed-off-by: Viktor Babrian <babrian.viktor@renyi.mta.hu>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In order to be able to move the stats increment from can_bus_off() into
can_change_state(), the increment had to be moved back into code that was using
can_bus_off() but not can_change_state().
As a side-effect, this patch fixes the following bugs:
* Redundant call to can_bus_off() in c_can.
* Bus-off counted twice in xilinx_can.
Signed-off-by: Andri Yngvason <andri.yngvason@marel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
use of regmap_read() and regmap_write() in c_can_hw_raminit_syscon()
is not safe as the RAMINIT register can be shared between different drivers
at least for TI SoCs.
To make the modification atomic we switch to using regmap_update_bits().
regmap_update_bits() skips writing to the register if it's read content is the
same as what is going to be written. This causes an issue for us when we
need to clear the DONE bit with the initial condition START:0, DONE:1 as
DONE bit must be written with 1 to clear it.
So we defer the clearing of DONE bit to later when we set the START bit.
There we are sure that START bit is changed from 0 to 1 so the write of
1 to already set DONE bit will happen.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
AM4372 SoC has 2 DCAN modules. Add compatible id and
raminit driver data for it. The driver data is same as AM3352
but this gives us flexibility to add AM4372 specific quirks
if required later.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
AM3352 SoC has 2 DCAN modules. Add compatible id and
raminit driver data for am3352 DCAN.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
DRA7 SoC has 2 CAN IPs. Provide compatible IDs and RAMINIT
register data for both.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
DRA7 CAN IP suffers from a problem which causes it to be prevented
from fully turning OFF (i.e. stuck in transition) if the module was
disabled while there was traffic on the CAN_RX line.
To work around this issue we select the SLEEP pin state by default
on probe and use the DEFAULT pin state on CAN up and back to the
SLEEP pin state on CAN down.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Some SoCs e.g. (TI DRA7xx) need a START pulse to start the
RAMINIT sequence i.e. START bit must be set and cleared before
checking for the DONE bit status.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Some TI SoCs like DRA7 have a RAMINIT register specification
different from the other AMxx SoCs and as expected by the
existing driver.
To add more insanity, this register is shared with other
IPs like DSS, PCIe and PWM.
Provides a more generic mechanism to specify the RAMINIT
register location and START/DONE bit position and use the
syscon/regmap framework to access the register.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Some platforms (e.g. TI) need special RAMINIT register handling.
Provide a way to store RAMINIT register description in driver data.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
We want to have more data than just can_dev_id to be present
in the driver data e.g. TI platforms need RAMINIT register
description. Introduce the c_can_driver_data structure and move
the can_dev_id into it.
Tidy up the way it is used on probe().
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
TI's RAMINIT DONE mechanism is buggy on AM43xx SoC and may not always
be set after the START bit is set. Although it seems to work fine even
in that case. So add a timeout mechanism to c_can_hw_raminit_wait_ti().
Don't bail out in that failure case but just print an error message.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Conflicts:
arch/mips/net/bpf_jit.c
drivers/net/can/flexcan.c
Both the flexcan and MIPS bpf_jit conflicts were cases of simple
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the correct 'mask' and 'value' bits to c_can_hw_raminit_wait_ti(). They
seem to have been swapped in the usage instances.
Reported-by: Jay Schroeder <jay.schroeder@garmin.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
devm_ioremap() returns NULL on error, not an ERR_PTR().
Fixes: 33cf756569 ('can: c_can_platform: Fix raminit, use devm_ioremap() instead of devm_ioremap_resource()')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.11
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
No need to manually copy debug settings into subdir Makefiles. kbuild
has a mechanism for inheriting, so let's use it.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The raminit register is shared register for both can0 and can1. Since commit:
32766ff net: can: Convert to use devm_ioremap_resource
devm_ioremap_resource() is used to map raminit register. When using both
interfaces the mapping for the can1 interface fails, leading to a non
functional can interface.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.11
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch uses devm_* APIs as they are device managed and make code simpler.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Conflicts:
drivers/net/bonding/bond_alb.c
drivers/net/ethernet/altera/altera_msgdma.c
drivers/net/ethernet/altera/altera_sgdma.c
net/ipv6/xfrm6_output.c
Several cases of overlapping changes.
The xfrm6_output.c has a bug fix which overlaps the renaming
of skb->local_df to skb->ignore_df.
In the Altera TSE driver cases, the register access cleanups
in net-next overlapped with bug fixes done in net.
Similarly a bug fix to send ALB packets in the bonding driver using
the right source address overlaps with cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers for 32-bit accesses and replace open-coded 32-bit access
with calls to helpers. Minimum changes are done to the pci case, as I
don't have access to that hardware.
Tested-by: Thor Thayer <tthayer@altera.com>
Signed-off-by: Thor Thayer <tthayer@altera.com>
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch makes the {read,write}_reg functions const, this is a preparation to
make use of {read,write}_reg in the hwinit callback.
Signed-off-by: Thor Thayer <tthayer@altera.com>
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In 2b9aecdce2 ("can: c_can: Disable rx split as workaround") a new Kconfig
option was introduced as a workaround. The tests performed by Alexander Stein
confirmed this option to be obsolete with all the other cleanups and fixes
that had been discussed that time:
http://marc.info/?l=linux-can&m=139746476821294&w=2
Both (author and tester) agreed to remove this Kconfig option again:
http://marc.info/?l=linux-can&m=139883820714229&w=2
As some more cleanups took place since then a simple revert is not possible.
This patch removes the entire option as it would behave when disabled.
Further beautification’s can be done later.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Conflicts:
drivers/net/ethernet/altera/altera_sgdma.c
net/netlink/af_netlink.c
net/sched/cls_api.c
net/sched/sch_api.c
The netlink conflict dealt with moving to netlink_capable() and
netlink_ns_capable() in the 'net' tree vs. supporting 'tc' operations
in non-init namespaces. These were simple transformations from
netlink_capable to netlink_ns_capable.
The Altera driver conflict was simply code removal overlapping some
void pointer cast cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Coverity complains that c_can_pci_probe() calls pci_enable_msi() without
checking the result:
CID 712278 (#1 of 1): Unchecked return value (CHECKED_RETURN) 3. check_return:
Calling pci_enable_msi_block without checking return value (as is done
elsewhere 88 out of 105 times).
88 pci_enable_msi(pdev);
This is CID 712278.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Reported-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Commit 6439fbce10 (can: c_can: fix error checking of priv->instance in
probe()) found the warning but applied a suboptimal solution. Since, both
pdev->id and of_alias_get_id() return integers, it makes sense to convert the
variable to an integer and avoid the cast.
Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
It's suffcient to kill the TXIE bit in the message control register
even if the documentation of C and D CAN says that it's not allowed to
do that while MSGVAL is set. Reality tells a different story and this
change gives us another 2% of CPU back for not waiting on I/O.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Mark suggested to use one IF for the softirq and the other for the
xmit function to avoid the xmit lock.
That requires to write the frame into the interface first, then handle
the echo skb and store the dlc before committing the TX request to the
message ram.
We use an atomic to handle the active buffers instead of reading the
MSGVAL register as thats way faster especially on PCH/x86.
Suggested-by: Mark <mark5@del-llc.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
