On a few Kria KR260 Robotics Starter Kit the PS-GEM SGMII linkup is not
happening after the resume. This is because serdes registers are reset
when FPD is off (in suspend state) and needs to be reprogrammed in the
resume path with the same default initialization as done in the first
stage bootloader psu_init routine.
To address the failure introduce a set of serdes registers to be saved in
the suspend path and then restore it on resume.
Fixes: 4a33bea003 ("phy: zynqmp: Add PHY driver for the Xilinx ZynqMP Gigabit Transceiver")
Signed-off-by: Piyush Mehta <piyush.mehta@amd.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/1722837547-2578381-1-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for printing some basic status information to debugfs. This
is helpful when debugging phy consumers to make sure they are configuring
the phy appropriately.
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Link: https://lore.kernel.org/r/20240628205540.3098010-6-sean.anderson@linux.dev
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Take the phy mutex in xlate to protect against concurrent
modification/access to gtr_phy. This does not typically cause any
issues, since in most systems the phys are only xlated once and
thereafter accessed with the phy API (which takes the locks). However,
we are about to allow userspace to access phys for debugging, so it's
important to avoid any data races.
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Link: https://lore.kernel.org/r/20240628205540.3098010-5-sean.anderson@linux.dev
Signed-off-by: Vinod Koul <vkoul@kernel.org>
For PCIe and DisplayPort, the phy instance represents the controller's
logical lane. Wait for the instance 0 phy's PLL to lock as other
instances will never lock. We do this in xpsgtr_wait_pll_lock so callers
don't have to determine the correct lane themselves.
The original comment is wrong about cumulative wait times. Since we are
just polling a bit, all subsequent waiters will finish immediately.
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Link: https://lore.kernel.org/r/20240628205540.3098010-4-sean.anderson@linux.dev
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The phy "type" is just the combination of protocol and instance, and is
never used apart from that. Store the instance directly, instead of
converting to a type first. No functional change intended.
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Link: https://lore.kernel.org/r/20240628205540.3098010-3-sean.anderson@linux.dev
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Lanes can use other lanes' reference clocks, as determined by refclk.
Use refclk to determine the clock to enable/disable instead of always
using the lane's own reference clock. This ensures the clock selected in
xpsgtr_configure_pll is the one enabled.
For the other half of the equation, always program REF_CLK_SEL even when
we are selecting the lane's own clock. This ensures that Linux's idea of
the reference clock matches the hardware. We use the "local" clock mux
for this instead of going through the ref clock network.
Fixes: 25d7008335 ("phy: xilinx: phy-zynqmp: dynamic clock support for power-save")
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Link: https://lore.kernel.org/r/20240628205540.3098010-2-sean.anderson@linux.dev
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/57a3338a1cec683ac84d48e00dbf197e15ee5481.1709886922.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The xlate callbacks are supposed to translate of_phandle_args to proper
provider without modifying the of_phandle_args. Make the argument
pointer to const for code safety and readability.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com> #Broadcom
Link: https://lore.kernel.org/r/20240217093937.58234-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Due to limited available frequency ratios, the reference clock rate may
not be exactly the same as the required rate. Allow a small (100 ppm)
deviation.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20230711194542.898230-1-sean.anderson@seco.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Enabling clock for all the lanes consumes power even PHY is active or
inactive. To resolve this, enable/disable clocks in phy_init/phy_exit.
By default clock is disabled for all the lanes. Whenever phy_init called
from USB, SATA, or display driver, etc. It enabled the required clock
for requested lane. On phy_exit cycle, it disabled clock for the active
PHYs.
During the suspend/resume cycle, each USB/ SATA/ display driver called
phy_exit/phy_init individually. It disabled clock on exit, and enabled
on initialization for the active PHYs.
Signed-off-by: Piyush Mehta <piyush.mehta@amd.com>
Link: https://lore.kernel.org/r/20230613140250.3018947-3-piyush.mehta@amd.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Added Runtime power management support to the xilinx phy driver and using
DEFINE_RUNTIME_DEV_PM_OPS new macros allows the compiler to remove the
unused dev_pm_ops structure and related functions if !CONFIG_PM without
the need to mark the functions __maybe_unused.
Signed-off-by: Piyush Mehta <piyush.mehta@amd.com>
Link: https://lore.kernel.org/r/20230613140250.3018947-2-piyush.mehta@amd.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
SGMII is validated on kria KR260 robotics starter kit. So modify the
comment description to include it in supported controllers list.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/1679940407-13131-1-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
TX_PROT_BUS_WIDTH and RX_PROT_BUS_WIDTH are single registers with
separate bit fields for each lane. The code in xpsgtr_phy_init_sgmii was
not preserving the existing register value for other lanes, so enabling
the PHY in SGMII mode on one lane zeroed out the settings for all other
lanes, causing other PS-GTR peripherals such as USB3 to malfunction.
Use xpsgtr_clr_set to only manipulate the desired bits in the register.
Fixes: 4a33bea003 ("phy: zynqmp: Add PHY driver for the Xilinx ZynqMP Gigabit Transceiver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20220126001600.1592218-1-robert.hancock@calian.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
PHY initialization for USB is required on linux boot or when
gt lane is changed from the current one and it is applicable
on PLL lock too.
Signed-off-by: Piyush Mehta <piyush.mehta@xilinx.com>
Link: https://lore.kernel.org/r/20210818084311.2643986-1-piyush.mehta@xilinx.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The current driver is not handling the clock enable/disable operations
properly. The clocks need to be handled correctly by enabling or
disabling at appropriate places. This patch adds code to handle the
same.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/1616588325-95602-1-git-send-email-manish.narani@xilinx.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Mark xpsgtr_suspend and xpsgtr_resume as __maybe_unused to fix the
following compiler warning when building with !CONFIG_PM_SLEEP:
drivers/phy/xilinx/phy-zynqmp.c:830:12: warning: ‘xpsgtr_resume’ defined but not used [-Wunused-function]
830 | static int xpsgtr_resume(struct device *dev)
| ^~~~~~~~~~~~~
drivers/phy/xilinx/phy-zynqmp.c:819:12: warning: ‘xpsgtr_suspend’ defined but not used [-Wunused-function]
819 | static int xpsgtr_suspend(struct device *dev)
| ^~~~~~~~~~~~~~
Also drop the existing #ifdef CONFIG_PM so the functions are always
compile-checked regardless of CONFIG_PM and/or CONFIG_PM_SLEEP being
set.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Link: https://lore.kernel.org/r/20200701141017.26931-1-tklauser@distanz.ch
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Xilinx ZynqMP SoCs have a Gigabit Transceiver with four lanes. All the
high speed peripherals such as USB, SATA, PCIE, Display Port and
Ethernet SGMII can rely on any of the four GT lanes for PHY layer. This
patch adds driver for that ZynqMP GT core.
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20200629120054.29338-3-laurent.pinchart@ideasonboard.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
