Commit Graph

252 Commits

Author SHA1 Message Date
Stefan Popa
cbd5dd387a drivers: iio: dac: Fix wrong license for ADI drivers
Analog Devices drivers are typically GPL v2 only. This patch fixes the
inconsistencies between the module license and SPDX.

Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2019-02-09 18:46:01 +00:00
Mircea Caprioru
192778fb96 iio: dac: ad5686: Add support for AD5674R/AD5679R
The AD5674R/AD5679R are low power, 16-channel, 12-/16-bit buffered voltage
output digital-to-analog converters (DACs). They include a 2.5 V internal
reference (enabled by default).

These devices are very similar to AD5684R/AD5686R, except that they have 16
channels.

Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2019-01-12 18:58:21 +00:00
Mircea Caprioru
0e76df5c97 iio: dac: ad5686: fix bit shift read register
This patch solves the register readback issue with the bit shift. When the
dac resolution was lower than the register size (ex. 12 bits out of 16
bits) the readback value was not shifted with the difference in bits and
the value was higher. Also a mask is applied on the read value in order to
get the value relative to the actual bit size.

Fixes: 0357e488b8 ("iio:dac:ad5686: Refactor the driver")
Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-12-08 15:45:09 +00:00
Stefan Popa
12d323cf6d iio:dac:ad5686: Add AD5310R support
The AD5310R is a single channel DAC with 10-bit precision, which is
part of the same family as AD5311R, except that it uses the spi interface
instead of i2c. The device has a built-in 2.5V reference which is enabled
by default.

Another important difference is that the SPI write command operation is
16 bits long. The first four bits represent the command, while the
remaining 12 bits are for data. In the control reg, DB9 and DB10 are used
for power-down modes, while DB8 is the REF bit. In order to accommodate
this change, a new regmap type was defined and checked accordingly.

Because AD5310R does not have a readback register, the read_raw operation
will return "Operation is not supported".

Datasheet:
Link: http://www.analog.com/media/en/technical-documentation/data-sheets/AD5310R_5311R.pdf

Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-12-08 15:35:55 +00:00
Charles-Antoine Couret
7a02ef7907 iio:dac:ti-dac7311 Add driver for Texas Instrument DAC7311
It is a driver for Texas Instruments 8/10/12-bit 1-channel
compatible with DAC6311 and DAC5311 chips.

Datasheet of this chip:
http://www.ti.com/lit/ds/symlink/dac7311.pdf

Signed-off-by: Charles-Antoine Couret <charles-antoine.couret@essensium.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-11-11 15:29:44 +00:00
Gustavo A. R. Silva
c65a0d84ee iio: dpot-dac: mark expected switch fall-through with text GCC expects.
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.

Notice that in this particular case, I replaced "...and fall through."
with the specific string "fall through", which is what GCC is
expecting to find thus supressing this false positive.

As Peter has observed this breaks the nice English flow, which is
less than ideal, but short of teaching GCC to read English, there
isn't a lot that we can do about it.

Addresses-Coverity-ID: 1462408 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-10-14 18:01:00 +01:00
Lars-Peter Clausen
8911a43bc1 iio: ad5064: Fix regulator handling
The correct way to handle errors returned by regualtor_get() and friends is
to propagate the error since that means that an regulator was specified,
but something went wrong when requesting it.

For handling optional regulators, e.g. when the device has an internal
vref, regulator_get_optional() should be used to avoid getting the dummy
regulator that the regulator core otherwise provides.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-09-29 13:28:47 +01:00
Greg Kroah-Hartman
4b55dce8b0 1st round of IIO new device support, features and cleanups in the 4.20 cycle.
There is a merge commit in here to pull in regmap support for repeatedly
 reading the same register (to read out FIFOs).  Used by the adxl372 driver.
 This will find uses elsewhere once we tidy up various drivers that are
 effectively doing this and relying on not enabling regcache.
 
 New device support
 * Analog devices ADXL372 accelerometer
   - new driver for this accelerometer including fifo and and interrupt support.
     Follow up patches enforce trigger validation, add sampling frequency
     control and filter bandwidth control.  A later series added i2c support
     to the existing SPI support.
 * ST lsm6dsx
   - rework and add support fo the LSM6DSO 6 axis mems sensor.
 * Linear LTC 1660 DAC
   - new driver supporting the LTC 1660 and LTC 1665 SPI DACs.
 * Microchip mcp3911 ADC.
   - new driver for this integrated analog front end and ADC.
 * Qualcomm SPMI PMIC5 adc driver
   - using the spmi framework, new driver and bindings for this ADC.
     Follow up patch adds some missing channels.
 
 Features
 * ad5758
   - support hard reset using a gpio (if provided).
 * mpu6050
   - Regulator support
 * qcom-spmi-adc5
   - Sanity check the channel numbers provided by DT to make sure the
     driver actually knows about them.
 * sc27xx
   - give raw data for channel 20 as it's used on all known boards for
     the headset which needs a custom converstion function.  If it turns
     out someone builds a board where this isn't true we will deal with it
     when it happens.
   - add ADC scale calibration.
 * tsl2772
   - support device tree binding to set the proximity led settings.
   - regulator supprot.
   - binding for apds9930 - trivial addition as register compatible with tsl2772.
 
 Cleanups / Minor fixes
 
 * adxl345
   - supress a static checker warning but explicitly checking if the id
     object is null.
 * bh1750
   - avoid CONFIG_PM_SLEEP checks.
   - SPDX.
 * bme680
   - spelling mistake
   - use clamp rather than open coding.
   - white space and other similar fixes.
   - rename MSK to MASK for clarifty and use GENMASK to specify them.
   - use the FIELD_GET macro rather than a very odd accessor of dividing by
     16 to get the shift.
   - rework to share handing for oversampling of the various channels in a
     unified way.
   - check explicitly for val2 in write_raw function to ensure it is 0.
   - drop some field defines that don't add anything.
 * dpot-adc
   - SPDX
 * envelope detector
   - SPDX
 * isl29501
   - fix an ancient compiler warning mostly because it results in much
     nicer code.
 * max30102
   - mark switch fall throughs.
 * max44000
   - drop an unused variable.
 * max512
   - avoid CONFIG_PM_SLEEP checks.
 * max5481
   - use of_device_get_match_data rather than open coding it.
 * max5821
   - avoid CONFIG_PM_SLEEP checks.
 * max9611
   - explicity cast an enum to an integer to make it totally clear that
     this is intended.
 * mcp4018
   - fix an inconsistent MODULE_LICENSE.
   - use of_device_get_match_data rather than open coding it.
 * mcp4531
   - use of_device_get_match_data rather than open coding it.
   - SPDX
 * mcp4725
   - avoid CONFIG_PM_SLEEP checks.
 * mcp4922
   - Fix error handling and prevent writing a negative to when setting the
     output voltage.
 * ms5611
   - drop deprecated compatible strings without manufacturer from being
     explicitly listed.  They are handled anyway.
   - SPDX
 * multiplexer
   - SPDX
 * qcom-vadc
   - fix inconsistent documentation for reg.
 * ti-dac5571
   - provide and of_match_table.
 
 * treewide
   - update Michael Hennerich's email address.
   - Use %pOFn rather than device_node.name.
 * documentation.
   - tidy up a wrong kernel version for the introduction of the
     position_relative ABI.
 -----BEGIN PGP SIGNATURE-----
 
 iQJFBAABCAAvFiEEbilms4eEBlKRJoGxVIU0mcT0FogFAluave0RHGppYzIzQGtl
 cm5lbC5vcmcACgkQVIU0mcT0Fogr/A//bfXkfYPO2tPQOe+Ut/isyKvceDFs4faJ
 0ogmVxrH5hwFe96vfB0RWcYhovKXONrRtqreMCiVPMjKxg5o+F3Q+eSj0qhxhG77
 bDV5CnF1GXiBe/02WSEs9B3L4oxu6Z/PGq2sGrlTfTy8NZxJW6biER1aWeBbxmR6
 nPBb9SXH4vuqiiF8UOwRB2ETelx2jXXCNFxmUVQ0bzCYgAp/n7B2ZJu6OxWIhBGC
 NEPYofFajNATJEGgTQmwmKNv6xL4wVSpZXMLO1hzKPe8arARBqPGjIg14srl+nWs
 HsOdsl/GkeOcPsI7aUvQO0zC5nOgU9iXtQFZQLq8D1xMQP9LzfRuLhymy8dH8hg+
 uUfxkJf0OwhqEW+6GJ0g4A2xaDHyM7JFQAV1/XCNS93qjpcgC7rcLbnSDy9u6SC/
 j3g3EFUXVYqOuFXbr+1TLrg/oJhnOkXp3Wbm/Di0zXJNYOtzQ9zSLp55HZLxvOOl
 zzLWCSkse9EAwHzVnl4BAd03Zw3Ewh9aAJlXQ7JKGtQSXo+PpFyIiyn8woQpzGV8
 OePhhmooOYVxI2Aua0UKhwa6lPeZT71zjpJyFCTFJqRwU3I/8HEDH5g+9dX6Vk6h
 CLF/fCLCkRa1ccDzFQbHai91xLflaYUsXdjOnQymJ5CYToni/IyPukrZ05b2IdvO
 XnMIaoVrAUU=
 =+9gG
 -----END PGP SIGNATURE-----

Merge tag 'iio-for-4.20a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next

Jonathan writes:

1st round of IIO new device support, features and cleanups in the 4.20 cycle.

There is a merge commit in here to pull in regmap support for repeatedly
reading the same register (to read out FIFOs).  Used by the adxl372 driver.
This will find uses elsewhere once we tidy up various drivers that are
effectively doing this and relying on not enabling regcache.

New device support
* Analog devices ADXL372 accelerometer
  - new driver for this accelerometer including fifo and and interrupt support.
    Follow up patches enforce trigger validation, add sampling frequency
    control and filter bandwidth control.  A later series added i2c support
    to the existing SPI support.
* ST lsm6dsx
  - rework and add support fo the LSM6DSO 6 axis mems sensor.
* Linear LTC 1660 DAC
  - new driver supporting the LTC 1660 and LTC 1665 SPI DACs.
* Microchip mcp3911 ADC.
  - new driver for this integrated analog front end and ADC.
* Qualcomm SPMI PMIC5 adc driver
  - using the spmi framework, new driver and bindings for this ADC.
    Follow up patch adds some missing channels.

Features
* ad5758
  - support hard reset using a gpio (if provided).
* mpu6050
  - Regulator support
* qcom-spmi-adc5
  - Sanity check the channel numbers provided by DT to make sure the
    driver actually knows about them.
* sc27xx
  - give raw data for channel 20 as it's used on all known boards for
    the headset which needs a custom converstion function.  If it turns
    out someone builds a board where this isn't true we will deal with it
    when it happens.
  - add ADC scale calibration.
* tsl2772
  - support device tree binding to set the proximity led settings.
  - regulator supprot.
  - binding for apds9930 - trivial addition as register compatible with tsl2772.

Cleanups / Minor fixes

* adxl345
  - supress a static checker warning but explicitly checking if the id
    object is null.
* bh1750
  - avoid CONFIG_PM_SLEEP checks.
  - SPDX.
* bme680
  - spelling mistake
  - use clamp rather than open coding.
  - white space and other similar fixes.
  - rename MSK to MASK for clarifty and use GENMASK to specify them.
  - use the FIELD_GET macro rather than a very odd accessor of dividing by
    16 to get the shift.
  - rework to share handing for oversampling of the various channels in a
    unified way.
  - check explicitly for val2 in write_raw function to ensure it is 0.
  - drop some field defines that don't add anything.
* dpot-adc
  - SPDX
* envelope detector
  - SPDX
* isl29501
  - fix an ancient compiler warning mostly because it results in much
    nicer code.
* max30102
  - mark switch fall throughs.
* max44000
  - drop an unused variable.
* max512
  - avoid CONFIG_PM_SLEEP checks.
* max5481
  - use of_device_get_match_data rather than open coding it.
* max5821
  - avoid CONFIG_PM_SLEEP checks.
* max9611
  - explicity cast an enum to an integer to make it totally clear that
    this is intended.
* mcp4018
  - fix an inconsistent MODULE_LICENSE.
  - use of_device_get_match_data rather than open coding it.
* mcp4531
  - use of_device_get_match_data rather than open coding it.
  - SPDX
* mcp4725
  - avoid CONFIG_PM_SLEEP checks.
* mcp4922
  - Fix error handling and prevent writing a negative to when setting the
    output voltage.
* ms5611
  - drop deprecated compatible strings without manufacturer from being
    explicitly listed.  They are handled anyway.
  - SPDX
* multiplexer
  - SPDX
* qcom-vadc
  - fix inconsistent documentation for reg.
* ti-dac5571
  - provide and of_match_table.

* treewide
  - update Michael Hennerich's email address.
  - Use %pOFn rather than device_node.name.
* documentation.
  - tidy up a wrong kernel version for the introduction of the
    position_relative ABI.
2018-09-14 10:38:48 +02:00
Stefan Popa
ff50593026 iio: dac: ad5758: Add support for hard reset
The ad5758 has a hardware reset active low input pin. This patch adds a
devicetree entry for a reset GPIO and a new ad5758_reset() function.
During
initialization, it is checked if the reset property is specified and the
the GPIO is being asserted, therefore the device will become active.

When the reset function is called, if the gpio_reset var is set, then
the
GPIO will be toggled, otherwise a software reset is performed.

Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-09-02 19:01:30 +01:00
Marcus Folkesson
91d05d7639 iio: dac: ti-dac5571: provide of_match_table to driver
Use the created list of of_device_id's as a match table.

Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-08-25 09:58:52 +01:00
Marcus Folkesson
0833627fc3 iio: dac: mcp4922: fix error handling in mcp4922_write_raw
Do not try to write negative values and make sure that the write goes well.

Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-08-25 09:47:36 +01:00
Marcus Folkesson
8316cebd1e iio: dac: add support for ltc1660
LTC1665/LTC1660 is a 8/10-bit Digital-to-Analog Converter
(DAC) with eight individual channels.

Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-08-25 09:24:07 +01:00
Arnd Bergmann
3723c63247 treewide: convert ISO_8859-1 text comments to utf-8
Almost all files in the kernel are either plain text or UTF-8 encoded.  A
couple however are ISO_8859-1, usually just a few characters in a C
comments, for historic reasons.

This converts them all to UTF-8 for consistency.

Link: http://lkml.kernel.org/r/20180724111600.4158975-1-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Simon Horman <horms@verge.net.au>			[IPVS portion]
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>	[IIO]
Acked-by: Michael Ellerman <mpe@ellerman.id.au>			[powerpc]
Acked-by: Rob Herring <robh@kernel.org>
Cc: Joe Perches <joe@perches.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-08-23 18:48:43 -07:00
Peter Rosin
3c4b0f4ddf iio: dpot-dac: switch to SPDX license identifier
Drop the boilerplate license text.

Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-08-20 19:27:47 +01:00
Marcus Folkesson
1a5bc41a3d iio: dac: mcp4725: avoid using CONFIG_PM_SLEEP
This is already handled by SIMPLE_DEV_PM_OPS().

Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-08-19 17:42:21 +01:00
Marcus Folkesson
b6ec220c28 iio: dac: max5821: avoid using CONFIG_PM_SLEEP
This is already handled by SIMPLE_DEV_PM_OPS().

Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-08-19 17:41:31 +01:00
Marcus Folkesson
fe8a542074 iio: dac: max517: avoid using CONFIG_PM_SLEEP
This is already handled by SIMPLE_DEV_PM_OPS().

Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-08-19 17:40:24 +01:00
Michael Hennerich
9920ed25ec drivers: iio: Update MODULE AUTHOR email address
no functional changes

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-08-19 17:23:39 +01:00
Stefan Popa
28d1a7ac2a iio: dac: Add AD5758 support
The AD5758 is a single channel DAC with 16-bit precision which uses the
SPI interface that operates at clock rates up to 50MHz.

The output can be configured as voltage or current and is available on a
single terminal.

Datasheet:
http://www.analog.com/media/en/technical-documentation/data-sheets/ad5758.pdf

Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-07-07 18:16:32 +01:00
Colin Ian King
5f0d4fd6b2 iio: dac: ltc2632 remove redundant pointer chip_info and spi_dev_id
Pointers chip_info and spi_dev_id are being assigned but are never used
hence they are redundant and can be removed.

Cleans up clang warning:
warning: variable 'chip_info' set but not used [-Wunused-but-set-variable]

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-07-07 17:46:25 +01:00
Colin Ian King
366995df8b iio: dac: ti-dac5571 remove redundant variable 'shift'
Variable shift is being assigned but is never used hence it is
redundant and can be removed.

Cleans up two clang warnings:
warning: variable ‘shift’ set but not used [-Wunused-but-set-variable]

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-07-07 17:43:37 +01:00
Greg Kroah-Hartman
f62252bf39 First set of IIO new device support, features and cleanups in the 4.19 cycle
The usual mixed bunch.  Particular good to see is the generic
 touch screen driver.  Will be interesting to see if this works
 for other ADCs without major changes.
 
 Core features
 * Channel types
   - New position relative channel type primarily for touch screen
     sensors to feed the generic touchscreen driver.
 
 New device support
 * ad5586
   - Add support for the AD5311R DAC.
 
 * Generic touch screen driver as an IIO consumer.
   - Note this is in input, but due to dependencies is coming through
     the IIO tree.
   - Specific support for this added to the at91-sama5d2 ADC.
   - Various necessary DT bindings added.
 
 Staging Drops
 * ADIS16060 gyro
   - A device with a very odd interface that was never cleanly supported.
     It's now very difficult to get, so unlikely it'll ever be fixed up.
 
 Cleanups and minor features and fixes
 * core
   - Fix y2038 timestamp issues now the core support is in place.
 * 104-quad-8
   - Provide some defines for magic numbers to help readability.
   - Fix an off by one error in register selection
 * ad7606
   - Put in a missing function parameter name in a prototype.
 * adis16023
   - Use generic sign_extend function rather than local version.
 * adis16240
   - Use generic sign_extend funciton rather than local version.
 * at91-sama5d2
   - Drop dependency on HAS_DMA now this is handled elsewhere.  Will
     improve build test coverage.
   - Add oversampling ratio control.  Note there is a minor ABI change
     here to increase the apparent depth to 14 bits so as to allow
     for transparent provision of different oversampling ratios that
     drop the actual bit depth to 13 or 12 bits.
 * hx711
   - Add a MAINTAINERS entry for this device.
 * inv_mpu6050
   - Replace the timestamp fifo 'special' code with generic timestamp
     handling.
   - Switch to using local store of timestamp divider rather than rate
     as that is more helpful for accurate time measurement.
   - Fix an unaligned access that didn't seem to be causing any trouble.
   - Use the fifo overflow bit to track the overflow status rather than
     a software counter.
   - New timestamping mechanism to deal with missed sample interrupts.
 * stm32-adc
   - Drop HAS_DMA build dependency.
 * sun4i-gpadc
   - Select REGMAP_IRQ a very rarely hit build issue fix.
 -----BEGIN PGP SIGNATURE-----
 
 iQJFBAABCAAvFiEEbilms4eEBlKRJoGxVIU0mcT0FogFAlsxT24RHGppYzIzQGtl
 cm5lbC5vcmcACgkQVIU0mcT0FogOHRAAllFPJBoq+nVqGAqe6CjSmWhAFdyv/Ey0
 4iDBsdBHrzhxnDuatqzbFhvu9TgqQxMBSbcRfqrGnJrnCFDNcvo1eJcxq13YFPCy
 EitRhu5kUdZ6Ez+OQOjX77wGlPyh8idZnaUkWjowOjnXztkHQjy6IWTbDKFk9bPY
 9fGBpmPDn1xaVPPWh7lZVAdTwCt2i+efG4sGyZyMQODjtM0q2G1MoHm9ioqgg8lN
 hzO7YIrZmLlXRUhapQ2/61uwa/2WMrcGK5v8eCGphEZnPN5lUWrT//w91+BCQpBC
 A9gRFpWblz5qHaRpNhzNbQjUrGvTAeIhF+bdOV2W+oI8CJhTJ0AlNqtUXs2pbaJn
 FO6jGwkC+jOA3XdE4tbiqenuMSZNggXBCgyRMfIK5WuIeBF02w57KHxgefkGTnQe
 Iqc9QDLLfkGDsOoh1l/+TMWjAxfXJLd7d04wYcRIDy6wumTi6GJxUesiQAnyq5eo
 Rg+o8gbfZcnbgzphBRoQjjftFMPeYdr48bCGCmjFjNnIPnemmUZg988gTggl6NST
 mzbFBsAnejmYpT393FPL0K9dLVUq5cRngQMuLVDjR4VnlQEVMyV0O+CsW83iSM36
 3nqpaUOapqsKJT74n62k1YtzJgxr1uoyMS0LGjldAPLDiTgMf9YiPCCihCpiCY89
 K9gE6lzS70A=
 =SvKj
 -----END PGP SIGNATURE-----

Merge tag 'iio-for-4.19a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next

Jonathan writes:

First set of IIO new device support, features and cleanups in the 4.19 cycle

The usual mixed bunch.  Particular good to see is the generic
touch screen driver.  Will be interesting to see if this works
for other ADCs without major changes.

Core features
* Channel types
  - New position relative channel type primarily for touch screen
    sensors to feed the generic touchscreen driver.

New device support
* ad5586
  - Add support for the AD5311R DAC.

* Generic touch screen driver as an IIO consumer.
  - Note this is in input, but due to dependencies is coming through
    the IIO tree.
  - Specific support for this added to the at91-sama5d2 ADC.
  - Various necessary DT bindings added.

Staging Drops
* ADIS16060 gyro
  - A device with a very odd interface that was never cleanly supported.
    It's now very difficult to get, so unlikely it'll ever be fixed up.

Cleanups and minor features and fixes
* core
  - Fix y2038 timestamp issues now the core support is in place.
* 104-quad-8
  - Provide some defines for magic numbers to help readability.
  - Fix an off by one error in register selection
* ad7606
  - Put in a missing function parameter name in a prototype.
* adis16023
  - Use generic sign_extend function rather than local version.
* adis16240
  - Use generic sign_extend funciton rather than local version.
* at91-sama5d2
  - Drop dependency on HAS_DMA now this is handled elsewhere.  Will
    improve build test coverage.
  - Add oversampling ratio control.  Note there is a minor ABI change
    here to increase the apparent depth to 14 bits so as to allow
    for transparent provision of different oversampling ratios that
    drop the actual bit depth to 13 or 12 bits.
* hx711
  - Add a MAINTAINERS entry for this device.
* inv_mpu6050
  - Replace the timestamp fifo 'special' code with generic timestamp
    handling.
  - Switch to using local store of timestamp divider rather than rate
    as that is more helpful for accurate time measurement.
  - Fix an unaligned access that didn't seem to be causing any trouble.
  - Use the fifo overflow bit to track the overflow status rather than
    a software counter.
  - New timestamping mechanism to deal with missed sample interrupts.
* stm32-adc
  - Drop HAS_DMA build dependency.
* sun4i-gpadc
  - Select REGMAP_IRQ a very rarely hit build issue fix.
2018-06-26 07:47:37 +08:00
Kees Cook
a86854d0c5 treewide: devm_kzalloc() -> devm_kcalloc()
The devm_kzalloc() function has a 2-factor argument form, devm_kcalloc().
This patch replaces cases of:

        devm_kzalloc(handle, a * b, gfp)

with:
        devm_kcalloc(handle, a * b, gfp)

as well as handling cases of:

        devm_kzalloc(handle, a * b * c, gfp)

with:

        devm_kzalloc(handle, array3_size(a, b, c), gfp)

as it's slightly less ugly than:

        devm_kcalloc(handle, array_size(a, b), c, gfp)

This does, however, attempt to ignore constant size factors like:

        devm_kzalloc(handle, 4 * 1024, gfp)

though any constants defined via macros get caught up in the conversion.

Any factors with a sizeof() of "unsigned char", "char", and "u8" were
dropped, since they're redundant.

Some manual whitespace fixes were needed in this patch, as Coccinelle
really liked to write "=devm_kcalloc..." instead of "= devm_kcalloc...".

The Coccinelle script used for this was:

// Fix redundant parens around sizeof().
@@
expression HANDLE;
type TYPE;
expression THING, E;
@@

(
  devm_kzalloc(HANDLE,
-	(sizeof(TYPE)) * E
+	sizeof(TYPE) * E
  , ...)
|
  devm_kzalloc(HANDLE,
-	(sizeof(THING)) * E
+	sizeof(THING) * E
  , ...)
)

// Drop single-byte sizes and redundant parens.
@@
expression HANDLE;
expression COUNT;
typedef u8;
typedef __u8;
@@

(
  devm_kzalloc(HANDLE,
-	sizeof(u8) * (COUNT)
+	COUNT
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(__u8) * (COUNT)
+	COUNT
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(char) * (COUNT)
+	COUNT
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(unsigned char) * (COUNT)
+	COUNT
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(u8) * COUNT
+	COUNT
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(__u8) * COUNT
+	COUNT
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(char) * COUNT
+	COUNT
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(unsigned char) * COUNT
+	COUNT
  , ...)
)

// 2-factor product with sizeof(type/expression) and identifier or constant.
@@
expression HANDLE;
type TYPE;
expression THING;
identifier COUNT_ID;
constant COUNT_CONST;
@@

(
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(TYPE) * (COUNT_ID)
+	COUNT_ID, sizeof(TYPE)
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(TYPE) * COUNT_ID
+	COUNT_ID, sizeof(TYPE)
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(TYPE) * (COUNT_CONST)
+	COUNT_CONST, sizeof(TYPE)
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(TYPE) * COUNT_CONST
+	COUNT_CONST, sizeof(TYPE)
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(THING) * (COUNT_ID)
+	COUNT_ID, sizeof(THING)
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(THING) * COUNT_ID
+	COUNT_ID, sizeof(THING)
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(THING) * (COUNT_CONST)
+	COUNT_CONST, sizeof(THING)
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(THING) * COUNT_CONST
+	COUNT_CONST, sizeof(THING)
  , ...)
)

// 2-factor product, only identifiers.
@@
expression HANDLE;
identifier SIZE, COUNT;
@@

- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	SIZE * COUNT
+	COUNT, SIZE
  , ...)

// 3-factor product with 1 sizeof(type) or sizeof(expression), with
// redundant parens removed.
@@
expression HANDLE;
expression THING;
identifier STRIDE, COUNT;
type TYPE;
@@

(
  devm_kzalloc(HANDLE,
-	sizeof(TYPE) * (COUNT) * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(TYPE) * (COUNT) * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(TYPE) * COUNT * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(TYPE) * COUNT * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(THING) * (COUNT) * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(THING) * (COUNT) * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(THING) * COUNT * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(THING) * COUNT * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
)

// 3-factor product with 2 sizeof(variable), with redundant parens removed.
@@
expression HANDLE;
expression THING1, THING2;
identifier COUNT;
type TYPE1, TYPE2;
@@

(
  devm_kzalloc(HANDLE,
-	sizeof(TYPE1) * sizeof(TYPE2) * COUNT
+	array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+	array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(THING1) * sizeof(THING2) * COUNT
+	array3_size(COUNT, sizeof(THING1), sizeof(THING2))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(THING1) * sizeof(THING2) * (COUNT)
+	array3_size(COUNT, sizeof(THING1), sizeof(THING2))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(TYPE1) * sizeof(THING2) * COUNT
+	array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+	array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
  , ...)
)

// 3-factor product, only identifiers, with redundant parens removed.
@@
expression HANDLE;
identifier STRIDE, SIZE, COUNT;
@@

(
  devm_kzalloc(HANDLE,
-	(COUNT) * STRIDE * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  devm_kzalloc(HANDLE,
-	COUNT * (STRIDE) * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  devm_kzalloc(HANDLE,
-	COUNT * STRIDE * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  devm_kzalloc(HANDLE,
-	(COUNT) * (STRIDE) * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  devm_kzalloc(HANDLE,
-	COUNT * (STRIDE) * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  devm_kzalloc(HANDLE,
-	(COUNT) * STRIDE * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  devm_kzalloc(HANDLE,
-	(COUNT) * (STRIDE) * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  devm_kzalloc(HANDLE,
-	COUNT * STRIDE * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
)

// Any remaining multi-factor products, first at least 3-factor products,
// when they're not all constants...
@@
expression HANDLE;
expression E1, E2, E3;
constant C1, C2, C3;
@@

(
  devm_kzalloc(HANDLE, C1 * C2 * C3, ...)
|
  devm_kzalloc(HANDLE,
-	(E1) * E2 * E3
+	array3_size(E1, E2, E3)
  , ...)
|
  devm_kzalloc(HANDLE,
-	(E1) * (E2) * E3
+	array3_size(E1, E2, E3)
  , ...)
|
  devm_kzalloc(HANDLE,
-	(E1) * (E2) * (E3)
+	array3_size(E1, E2, E3)
  , ...)
|
  devm_kzalloc(HANDLE,
-	E1 * E2 * E3
+	array3_size(E1, E2, E3)
  , ...)
)

// And then all remaining 2 factors products when they're not all constants,
// keeping sizeof() as the second factor argument.
@@
expression HANDLE;
expression THING, E1, E2;
type TYPE;
constant C1, C2, C3;
@@

(
  devm_kzalloc(HANDLE, sizeof(THING) * C2, ...)
|
  devm_kzalloc(HANDLE, sizeof(TYPE) * C2, ...)
|
  devm_kzalloc(HANDLE, C1 * C2 * C3, ...)
|
  devm_kzalloc(HANDLE, C1 * C2, ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(TYPE) * (E2)
+	E2, sizeof(TYPE)
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(TYPE) * E2
+	E2, sizeof(TYPE)
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(THING) * (E2)
+	E2, sizeof(THING)
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(THING) * E2
+	E2, sizeof(THING)
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	(E1) * E2
+	E1, E2
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	(E1) * (E2)
+	E1, E2
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	E1 * E2
+	E1, E2
  , ...)
)

Signed-off-by: Kees Cook <keescook@chromium.org>
2018-06-12 16:19:22 -07:00
Stefan Popa
d8084a048c iio:dac:ad5686: Add AD5311R support
AD5311R is a single channel DAC with 10-bit precision and i2c interface.
The device includes a 2.5V internal reference which is enabled by default.

This device is similar to AD5691R/AD5692R/AD5693/AD5693R, the only
difference is that it has 10-bit precision.

Datasheet:
http://www.analog.com/media/en/technical-documentation/data-sheets/AD5310R_5311R.pdf

Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-06-10 14:30:09 +01:00
Silvan Murer
9ff1d5009f iio: dac: Add support for external reference voltage through the regulator framework.
Signed-off-by: Silvan Murer <silvan.murer@gmail.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-05-22 18:24:48 +01:00
Silvan Murer
0f6a2165af iio: dac: fix missing of_match_table assignment in the LTC 2632 device
Signed-off-by: Silvan Murer <silvan.murer@gmail.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-05-22 18:20:55 +01:00
Stefan Popa
1dbae4c6cd iio:dac:ad5686: Add AD5681R/AD5682R/AD5683/AD5683R support
The AD5681R/AD5682R/AD5683/AD5683R are a family of one channel DACs with
12-bit, 14-bit and 16-bit precision respectively. The devices have either
no built-in reference, or built-in 2.5V reference.

These devices are similar to AD5691R/AD5692R/AD5693/AD5693R except
with a few notable differences:
 * they use the SPI interface instead of I2C
 * in the write control register, DB18 and DB17 are used for setting the
   power mode, while DB16 is the REF bit. This is why a new regmap type
   was defined and checked accordingly.
 * the shift register is 24 bits wide, the first four bits are the command
   bits followed by the data bits. As the data comprises of 20-bit, 18-bit
   or 16-bit input code, this means that 4 LSB bits are don't care. This is
   why the data needs to be shifted on the left with four bits. Therefore,
   AD5683_REGMAP is checked inside a switch case in the ad5686_spi_write()
   function. On the other hand, similar devices such as AD5693R family,
   have the 4 MSB command bits followed by 4 don't care bits.

Datasheet:
http://www.analog.com/media/en/technical-documentation/data-sheets/AD5683R_5682R_5681R_5683.pdf

Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-05-20 11:45:45 +01:00
Stefan Popa
be1b24d245 iio:dac:ad5686: Add AD5691R/AD5692R/AD5693/AD5693R support
The AD5691R/AD5692R/AD5693/AD5693R are a family of one channel DACs with
12-bit, 14-bit and 16-bit precision respectively. The devices have either
no built-in reference, or built-in 2.5V reference.

These devices are pretty similar to AD5671R/AD5675R and
AD5694/AD5694R/AD5695R/AD5696/AD5696R, except that they have one channel.
Another difference is that they use a write control register(addr 0x04) for
setting the power down modes and the internal reference instead of separate
registers for each function.

Datasheet:
http://www.analog.com/media/en/technical-documentation/data-sheets/AD5693R_5692R_5691R_5693.pdf

Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-05-20 11:36:28 +01:00
Greg Kroah-Hartman
6a8b25abf1 1st round of IIO new device support, features and cleanup for the 4.18 cycle
A nice mix this time of excellent cleanups (many to send drivers
 speeding toward staging graduations) and new drivers / device support.
 A good part of this is Brian Masney's never ending task on the tsl2x7x
 driver.  The end is in sight so hopefully we'll get that one out of
 staging very soon!
 
 New device support
 * AD5686
   - Support AD5685R (was wrongly present as AD5685)
   - Support AD5672R, AD5676, AD5676, AD5684R and AD5686R 4 and 8 channel
     SPI DACs with various precisions.
   - Support AD5671R, AD5675R, AD5694, AD5694R, AD5695R, AD5696 and AD5696R
     I2C DACs with various percisions and numbers of channels.
 * Analog front end rescale driver - New driver.
   - Support current sensing usings a shunt resistor.
   - Support simple voltage dividers.
   - support simple current sense amplifiers.
 * TI dac5571
   - New driver and device bindings supporting:
     dac5571, dac6571, dac7571, dac5574, dac6574, dac7574,
     dac5573, dac6573 and dac7573
 * Meson-adc
   - Support for Meson AXG with DT bindings.
 * mpu6050
   - Support the mpu9255 which only requires additional WHOAMI entry and
     compatible string.
 * st_lsm6dsx
   - Support for lsm330dlc combinded accelerometer and gyro sensors with
     DT bindings.
 * stm32_adc
   - Add support for STM32MP1 with bindings.
 
 Staging graduations
 * adis16201 after some excelent cleanup by Himanshu Jha.
 * adis16029 after some excelent cleanup by Shreeya Patel.
 
 New features:
 * ABI docs
   - Add core ABI docs for angle channels.
 * inv_mpu6050
   - Provide support for the full range of interrupts the device
     supports.
 * st_accel
   - Add SMO8840 ACPI ID seen in the wild on some Lenovo machines.
 * stx104
   - Provide a multiple gpio get function.
 
 Cleanups / Minor fixes
 * core
   - Use new nested structure support to improve kernel-doc.
 * ad2s1200
   - Use be16_to_cpup instead of opencoding.
 * ad5686
   - Indentation tidy up.
   - Switch to SPDX
   - Refactor to allow various numbers of channels.
   - Refactor to separate core and SPI specific support, prior to
     addition of i2c equivalent devices.
 * ad7606
   - Use drvdata directly from device rather than boucing via the
     platform_device structure.
 * ad7746
   - Replace opencoded byte swapped i2c calls with _swapped variants.
   - White space and line break readability improvements.
   - Reorder includes and variable declarations where appropriate.
 * ad7791
   - Changes to the AD ADC library used by this driver took in the
     sampling frequency.  This lead to be the wrong path being the one
     tied to the resulting attribute, so it didn't work, and a warning
     to be printed.
 * ad7780
   - Remove apparent support for sampling frequency control on devices
     that don't support changing the sampling attributes.
 * ade7854
   - Fix a read of the wrong number of bits.
   - Improve error handling on i2c read/write errors.
   - Rework i2c and spi code to reduce duplication.
 * adis16201 (staging)
   - Improve meaning inherent in some macro names by adding units etc
     where relevant.
   - Adjust comments to improve detail and drop the irrelevant.
   - Rename register address definitions definitions to add a _REG
     postfix, clearly separating them from field definitions. Reorganize
     the definitions to group register address and fields.
   - Use sign_extend32 rather than open coding.
   - Reverse Xmas tree ordering where appropriate and align function args.
   - Remove unused headers.
   - Use GENMASK where appropriate instead of open coding.
 * adis16209 (staging)
   - Indent field definitions to visually separate them from
     register address definitions.
   - Use reverse xmas tree ordering where appropriate.
   - Add some whitespace where it will help readability.
   - Drop some unused headers.
   - Use GENMASK where appropriate.
 * ad2s1200
   - Drop unnecessary includes and reorder alphabetically.
   - Reverse xmas tree and blank line cleanups.
 * atlas-ph-sensor
   - Use msleep instead of usleep_range where the precise value doesn't
     matter and the delays are long.
 * bcm150
   - Drop transaction splitting as core now handles it.
 * cros_ec
   - Move the shared header to the include/iio/common directory.
     This brings it inline with the other multiple type devices.
   - Use drvdata directly from device rather than boucing via the
     platform_device structure.
 * hid-sensors
   - Use drvdata directly from device rather than boucing via the
     platform_device structure.
 * inv_mpu6050
   - Clear out a second function definition for the same function.
   - Don't flush fifo when the iio buffer is full but just drop excess
     data.
   - Tidy up set_power_itg and ensure it is used in the right places.
   - Use set_power_itg rather than opencoding it again in the i2c mux
     control.
   - Make sure error paths disable the power if undoing power on.
   - Used managed devm_ functions during probe. Delete remove function.
   - Refactor to pull raw data read out of read_raw function.
   - Simplify data reading error paths.
   - Only enable the i2c mux for chips with the i2c aux bus (not icm20608)
   - Fix a potential deadlock due to varying lock ordering.
   - Fix an issue where first sample from gyro after enabling is unstable
     by dropping the first sample.
   - Fix an issue where the user_ctrl register is incorrectly overwritten.
   - Tidy up some grammar and spelling minor issus.
 * mcp320x
   - Use vendor compatible strings.
 * mcp4018
   - Switch to using i2c .probe_new.
 * mcp4351
   - switch to using i2c .probe_new.
 * meson-adc
   - rework handing on common ADC platform data so it can be shared
     across multiple families of SoCs.
 * sca3000
   - Fix an error handling path if the ring configure fails.
 * st_lsm6dsx
   - Fix a wrong fifo threshold mask (no actual effect)
 * stm32-dfsdm
   - Style fixes and cleanups.
   - Check filter ID is in range and check spi-max-frequency.
 * tsl2x7x (staging)
   - Drop some unnecessary function calls, unused variables and
     unnecessary local variables.
   - Fix wrong interrupt type.
   - Avoid unnecessary double clear of interrupt.
   - Simplify proximity calibration call which did various things
     unrelated to actually calibrating.
   - Separate control of the proximity and ALS interrupts.
   - Improve consistency of logging.
   - Separate ALS and proximity persistence settings as they have
     separate hardware controls.
   - Tidy up variable ordering.
   - Add Brian to copyright notice given consider work on this driver.
   - Take advantage of hardware support for I2C address auto increment.
   - Combine individuaal enable and period attributes for the two
     directions on the threshold events into a single value as the
     hardware doesn't separate them.
   - Move integration_time* attributes from light channel to
     intensity value as they effect the intensity readings directly
     and the light reading only indirectly.  Hence this better
     reflects reality. Also move the calibscale_available.
   - Avoid returning an error in the IRQ handler.
   - Hard code the reg value in _clear_interrupts as it only takes
     one value in the code.   Result is the function has little
     purpose so opencode the two remaining i2c_smbus_write_byte
     calls.
   - Drop some unnecessary checking of the chip status register.
   - Tidy up return path in _write_interrupt_config.
   - Tidy up the ID verification code.
   - Move the power and diode settings defines into the header as these
     are needed for platform data configuration.
   - Various renames and comment cleanups for consistency and clarity.
   - Use actual device defaults for default startup settings.
   - SPDX
   - Add some range sanity checking to sysfs attribute writes.
   - Don't provide event interfaces if the interrupt line isn't available.
   - Use IIO_CONST_ATTR macro for calibscale_available as it's a constant
     string.
   - Fix the integration time and lux equations.
   - Make device IDs explicit index values in the device_channel_config array.
 -----BEGIN PGP SIGNATURE-----
 
 iQJFBAABCAAvFiEEbilms4eEBlKRJoGxVIU0mcT0FogFAlr0uigRHGppYzIzQGtl
 cm5lbC5vcmcACgkQVIU0mcT0FoiRhw//bIv57xenV6WV3+7Xmrp/rG4OBVzt8riD
 d9HczYKZE8/tqfB9cjF5e/xOpfin99eXBqEMWecidh3BxMNKXgnbvvCYCXF+m47D
 3cYlWvGbyZ2lbvqwbYCkk4xKfPNbRHBo5NX9TB08wf7DrAjmaudxmxDSFrRYQCho
 3Z3H2o54z1i/iJud61TApEONxr7H5oFdeb6uwNB5UVlG7XING9mfWbmlSzdlxW4X
 lHG4hC1/Pz/F4WjiLvNKccjhuq1f60CwSppKvfihq1IZKYKyHvSWjOicwrNb3QB2
 Kr0dT8yDqNKcKU1tsfgfR+YFeLKq52Ik4whulk8mkL7E4IWVIkGbL0ewkPwZ0YqO
 Cj9Nv52vzYS7x9Dj7R6f23Lwq30a19WKXixybjdo9zV14S0XKfzTmU7xC/4yhEjh
 yUg9QPjWxE5rAUTSjNF0C6tv786Y3aVYBp2jscIroSutipa6cUyc2rOKssM6GTZs
 vyRElGiUEXbg7uI7GrwN4PJszho47ptkFGn/o88Sy90KjUJ0mP15NTlp4IeSiVc/
 sM4YHHQ7tldcKqsaKeGbH8JwJNvzj9Kh20zniYd9lSZkeZusSkZUvd1FgB5uUocb
 ZZEG2IzCLM/utH49yXyaUkRS/lqoGCcObDkIHbsE1OM8q2bnZxaUYEMumxIpAs7l
 W2LBlr3vGF4=
 =egCX
 -----END PGP SIGNATURE-----

Merge tag 'iio-for-4.18a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next

Jonathan writes:

1st round of IIO new device support, features and cleanup for the 4.18 cycle

A nice mix this time of excellent cleanups (many to send drivers
speeding toward staging graduations) and new drivers / device support.
A good part of this is Brian Masney's never ending task on the tsl2x7x
driver.  The end is in sight so hopefully we'll get that one out of
staging very soon!

New device support
* AD5686
  - Support AD5685R (was wrongly present as AD5685)
  - Support AD5672R, AD5676, AD5676, AD5684R and AD5686R 4 and 8 channel
    SPI DACs with various precisions.
  - Support AD5671R, AD5675R, AD5694, AD5694R, AD5695R, AD5696 and AD5696R
    I2C DACs with various percisions and numbers of channels.
* Analog front end rescale driver - New driver.
  - Support current sensing usings a shunt resistor.
  - Support simple voltage dividers.
  - support simple current sense amplifiers.
* TI dac5571
  - New driver and device bindings supporting:
    dac5571, dac6571, dac7571, dac5574, dac6574, dac7574,
    dac5573, dac6573 and dac7573
* Meson-adc
  - Support for Meson AXG with DT bindings.
* mpu6050
  - Support the mpu9255 which only requires additional WHOAMI entry and
    compatible string.
* st_lsm6dsx
  - Support for lsm330dlc combinded accelerometer and gyro sensors with
    DT bindings.
* stm32_adc
  - Add support for STM32MP1 with bindings.

Staging graduations
* adis16201 after some excelent cleanup by Himanshu Jha.
* adis16029 after some excelent cleanup by Shreeya Patel.

New features:
* ABI docs
  - Add core ABI docs for angle channels.
* inv_mpu6050
  - Provide support for the full range of interrupts the device
    supports.
* st_accel
  - Add SMO8840 ACPI ID seen in the wild on some Lenovo machines.
* stx104
  - Provide a multiple gpio get function.

Cleanups / Minor fixes
* core
  - Use new nested structure support to improve kernel-doc.
* ad2s1200
  - Use be16_to_cpup instead of opencoding.
* ad5686
  - Indentation tidy up.
  - Switch to SPDX
  - Refactor to allow various numbers of channels.
  - Refactor to separate core and SPI specific support, prior to
    addition of i2c equivalent devices.
* ad7606
  - Use drvdata directly from device rather than boucing via the
    platform_device structure.
* ad7746
  - Replace opencoded byte swapped i2c calls with _swapped variants.
  - White space and line break readability improvements.
  - Reorder includes and variable declarations where appropriate.
* ad7791
  - Changes to the AD ADC library used by this driver took in the
    sampling frequency.  This lead to be the wrong path being the one
    tied to the resulting attribute, so it didn't work, and a warning
    to be printed.
* ad7780
  - Remove apparent support for sampling frequency control on devices
    that don't support changing the sampling attributes.
* ade7854
  - Fix a read of the wrong number of bits.
  - Improve error handling on i2c read/write errors.
  - Rework i2c and spi code to reduce duplication.
* adis16201 (staging)
  - Improve meaning inherent in some macro names by adding units etc
    where relevant.
  - Adjust comments to improve detail and drop the irrelevant.
  - Rename register address definitions definitions to add a _REG
    postfix, clearly separating them from field definitions. Reorganize
    the definitions to group register address and fields.
  - Use sign_extend32 rather than open coding.
  - Reverse Xmas tree ordering where appropriate and align function args.
  - Remove unused headers.
  - Use GENMASK where appropriate instead of open coding.
* adis16209 (staging)
  - Indent field definitions to visually separate them from
    register address definitions.
  - Use reverse xmas tree ordering where appropriate.
  - Add some whitespace where it will help readability.
  - Drop some unused headers.
  - Use GENMASK where appropriate.
* ad2s1200
  - Drop unnecessary includes and reorder alphabetically.
  - Reverse xmas tree and blank line cleanups.
* atlas-ph-sensor
  - Use msleep instead of usleep_range where the precise value doesn't
    matter and the delays are long.
* bcm150
  - Drop transaction splitting as core now handles it.
* cros_ec
  - Move the shared header to the include/iio/common directory.
    This brings it inline with the other multiple type devices.
  - Use drvdata directly from device rather than boucing via the
    platform_device structure.
* hid-sensors
  - Use drvdata directly from device rather than boucing via the
    platform_device structure.
* inv_mpu6050
  - Clear out a second function definition for the same function.
  - Don't flush fifo when the iio buffer is full but just drop excess
    data.
  - Tidy up set_power_itg and ensure it is used in the right places.
  - Use set_power_itg rather than opencoding it again in the i2c mux
    control.
  - Make sure error paths disable the power if undoing power on.
  - Used managed devm_ functions during probe. Delete remove function.
  - Refactor to pull raw data read out of read_raw function.
  - Simplify data reading error paths.
  - Only enable the i2c mux for chips with the i2c aux bus (not icm20608)
  - Fix a potential deadlock due to varying lock ordering.
  - Fix an issue where first sample from gyro after enabling is unstable
    by dropping the first sample.
  - Fix an issue where the user_ctrl register is incorrectly overwritten.
  - Tidy up some grammar and spelling minor issus.
* mcp320x
  - Use vendor compatible strings.
* mcp4018
  - Switch to using i2c .probe_new.
* mcp4351
  - switch to using i2c .probe_new.
* meson-adc
  - rework handing on common ADC platform data so it can be shared
    across multiple families of SoCs.
* sca3000
  - Fix an error handling path if the ring configure fails.
* st_lsm6dsx
  - Fix a wrong fifo threshold mask (no actual effect)
* stm32-dfsdm
  - Style fixes and cleanups.
  - Check filter ID is in range and check spi-max-frequency.
* tsl2x7x (staging)
  - Drop some unnecessary function calls, unused variables and
    unnecessary local variables.
  - Fix wrong interrupt type.
  - Avoid unnecessary double clear of interrupt.
  - Simplify proximity calibration call which did various things
    unrelated to actually calibrating.
  - Separate control of the proximity and ALS interrupts.
  - Improve consistency of logging.
  - Separate ALS and proximity persistence settings as they have
    separate hardware controls.
  - Tidy up variable ordering.
  - Add Brian to copyright notice given consider work on this driver.
  - Take advantage of hardware support for I2C address auto increment.
  - Combine individuaal enable and period attributes for the two
    directions on the threshold events into a single value as the
    hardware doesn't separate them.
  - Move integration_time* attributes from light channel to
    intensity value as they effect the intensity readings directly
    and the light reading only indirectly.  Hence this better
    reflects reality. Also move the calibscale_available.
  - Avoid returning an error in the IRQ handler.
  - Hard code the reg value in _clear_interrupts as it only takes
    one value in the code.   Result is the function has little
    purpose so opencode the two remaining i2c_smbus_write_byte
    calls.
  - Drop some unnecessary checking of the chip status register.
  - Tidy up return path in _write_interrupt_config.
  - Tidy up the ID verification code.
  - Move the power and diode settings defines into the header as these
    are needed for platform data configuration.
  - Various renames and comment cleanups for consistency and clarity.
  - Use actual device defaults for default startup settings.
  - SPDX
  - Add some range sanity checking to sysfs attribute writes.
  - Don't provide event interfaces if the interrupt line isn't available.
  - Use IIO_CONST_ATTR macro for calibscale_available as it's a constant
    string.
  - Fix the integration time and lux equations.
  - Make device IDs explicit index values in the device_channel_config array.
2018-05-11 09:50:04 +02:00
Sean Nyekjaer
df38a4a72a iio: dac: add TI DAC5571 family support
This patch adds support for the Texas Intruments DAC5571 Family.

Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-05-06 18:49:42 +01:00
Stefan Popa
4177381b44 iio:dac:ad5686: Add AD5671R/75R/94/94R/95R/96/96R support
The AD5694/AD5694R/AD5695R/AD5696/AD5696R are a family of 4 channel DACs
with 12-bit, 14-bit and 16-bit precision respectively. The devices have
either no built-in reference, or built-in 2.5V reference.

The AD5671R/AD5675R are similar, except that they have 8 instead of 4
channels.

These devices are similar to AD5672R/AD5676/AD5676R and
AD5684/AD5684R/AD5684/AD5685R/AD5686/AD5686R, except that they use i2c
instead of spi.

Datasheets:
http://www.analog.com/media/en/technical-documentation/data-sheets/AD5671R_5675R.pdf
http://www.analog.com/media/en/technical-documentation/data-sheets/AD5696R_5695R_5694R.pdf

Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-04-15 19:39:48 +01:00
Stefan Popa
0357e488b8 iio:dac:ad5686: Refactor the driver
In this patch restructures the existing ad5686 driver by adding a module
for SPI and a header file, while the baseline module deals with the
chip-logic.

This is a necessary step, as this driver should support in the future
similar devices which differ only in the type of interface used (I2C
instead of SPI).

Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-04-15 19:36:32 +01:00
Stefan Popa
98baf78e6d iio:dac:ad5686: Add AD5672R/76/76R/84R/86R support
The AD5684R/AD5686R are a family of 4 channel DACs with 12-bit, 14-bit and
16-bit precision respectively. The devices come either with a built-in
reference or no built-in reference.

The AD5672R/AD5676/AD5676R are similar, except that they have 8 channels
instead of 4.

Datasheets:
http://www.analog.com/media/en/technical-documentation/data-sheets/AD5672R_5676R.pdf
http://www.analog.com/media/en/technical-documentation/data-sheets/AD5686R_5685R_5684R.pdf

Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-04-15 19:32:20 +01:00
Stefan Popa
fe642e2dfc iio:dac:ad5686: Add support for AD5685R
This driver acctually supports the AD5685R device and NOT the AD5685, which
does not exist.  Maintain old id entry in case we have devicetrees
out there which are using the wrong name.

More information can be found in the datasheet:
http://www.analog.com/media/en/technical-documentation/data-sheets/AD5686_5684.pdf

Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-04-15 19:19:58 +01:00
Stefan Popa
f4a27306d4 iio:dac:ad5686: Add support for various number of channels
This patch adds a new num_channels attribute as part of the
ad5686_chip_info struct which replaces the AD5686_DAC_CHANNELS define. This
is a necessary step, since this driver should support similar devices which
differ only in the number of channels.

Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-04-15 19:15:54 +01:00
Stefan Popa
16a3c17575 iio:dac:ad5686: Change license description
Add GPLv2+ SPDX identifier and remove license notice to keep the whole
purpose of using an SPDx id.

Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-04-15 19:13:04 +01:00
Stefan Popa
25ffba7a2a iio:dac:ad5686: Style fixes no functional changes
This patch fixes some indentation issues and does not modify the
functionality of the driver.

Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-04-15 19:10:59 +01:00
Linus Torvalds
1b2951dd99 This is the bulk of GPIO changes for the v4.17 kernel cycle:
New drivers:
 
 - Nintendo Wii GameCube GPIO, known as "Hollywood"
 
 - Raspberry Pi mailbox service GPIO expander
 
 - Spreadtrum main SC9860 SoC and IEC GPIO controllers.
 
 Improvements:
 
 - Implemented .get_multiple() callback for most of the
   high-performance industrial GPIO cards for the ISA bus.
 
 - ISA GPIO drivers now select the ISA_BUS_API instead of
   depending on it. This is merged with the same pattern
   for all the ISA drivers and some other Kconfig cleanups
   related to this.
 
 Cleanup:
 
 - Delete the TZ1090 GPIO drivers following the deletion of
   this SoC from the ARM tree.
 
 - Move the documentation over to driver-api to conform with
   the rest of the kernel documentation build.
 
 - Continue to make the GPIO drivers include only
   <linux/gpio/driver.h> and not the too broad <linux/gpio.h>
   that we want to get rid of.
 
 - Managed to remove VLA allocation from two drivers pending
   more fixes in this area for the next merge window.
 
 - Misc janitorial fixes.
 -----BEGIN PGP SIGNATURE-----
 
 iQIcBAABAgAGBQJaxIehAAoJEEEQszewGV1zlEAP/3p3E6J8vPqJNV/C39c40krC
 ajo0ndiTC7cotmCXNQOl9xfMCTgkjBtx3WEKwTDfCsuWW+2YB0DRmMd0Bkf2RWjQ
 nM4rB64FzAu+rdD9jdGtfn24ofylSRFaHNQ/V8Prc2JVAXJt4DS97h+6kwzIAqCm
 A/xXQAx67k5qoTXLvR2n/8LX8TphSe2kwH/f/3/lJpNLfLCRRJ3GqJfpa72jw2eL
 4VIPc6KmttkqzJ1GFtzLPfhkhRr0p4sSzUNydlj5BKhmOSVu6Afv5ylgpK/p38dQ
 mGvNqFnU0lpwelsoZK75YikDFbqQjn4XkXJGvmIRMw4qM7crcw5oSkeMwCrcGqJW
 7Uo7NoQU94wcQSZTppFQdaJs7NHdcnpW7jcfRYYetZL/6eDGBtfxoym90Lyjvaqs
 y+ykofbadI0X/9omO5j+qozvIneLam/CF7iDRUb/5t1LJbNwtXUsVYhz3FuwPDt1
 ZHb6w+np9ZHN6H9jz3b/F9B/uQt54pshm7NorSXrJvZfKrv8kV14MoHgYsuQDDjV
 khbveygB8DwaPeV4XjpLeYhJB1L/Wjf46CVD6tyaCRDByGQmdoJEQF9QB2CxrF2J
 ouaaaS8tSC0IK/mKMMgJxC1Vr2gh0NMlQ3AL9EJDJvX+9RoIA2gwtBAiGnlEcdq3
 GyFAZ0szb5P4BaNnX9qc
 =C5t5
 -----END PGP SIGNATURE-----

Merge tag 'gpio-v4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio

Pull GPIO updates from Linus Walleij:
 "This is the bulk of GPIO changes for the v4.17 kernel cycle:

  New drivers:

   - Nintendo Wii GameCube GPIO, known as "Hollywood"

   - Raspberry Pi mailbox service GPIO expander

   - Spreadtrum main SC9860 SoC and IEC GPIO controllers.

  Improvements:

   - Implemented .get_multiple() callback for most of the
     high-performance industrial GPIO cards for the ISA bus.

   - ISA GPIO drivers now select the ISA_BUS_API instead of depending on
     it. This is merged with the same pattern for all the ISA drivers
     and some other Kconfig cleanups related to this.

  Cleanup:

   - Delete the TZ1090 GPIO drivers following the deletion of this SoC
     from the ARM tree.

   - Move the documentation over to driver-api to conform with the rest
     of the kernel documentation build.

   - Continue to make the GPIO drivers include only
     <linux/gpio/driver.h> and not the too broad <linux/gpio.h> that we
     want to get rid of.

   - Managed to remove VLA allocation from two drivers pending more
     fixes in this area for the next merge window.

   - Misc janitorial fixes"

* tag 'gpio-v4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (77 commits)
  gpio: Add Spreadtrum PMIC EIC driver support
  gpio: Add Spreadtrum EIC driver support
  dt-bindings: gpio: Add Spreadtrum EIC controller documentation
  gpio: ath79: Fix potential NULL dereference in ath79_gpio_probe()
  pinctrl: qcom: Don't allow protected pins to be requested
  gpiolib: Support 'gpio-reserved-ranges' property
  gpiolib: Change bitmap allocation to kmalloc_array
  gpiolib: Extract mask allocation into subroutine
  dt-bindings: gpio: Add a gpio-reserved-ranges property
  gpio: mockup: fix a potential crash when creating debugfs entries
  gpio: pca953x: add compatibility for pcal6524 and pcal9555a
  gpio: dwapb: Add support for a bus clock
  gpio: Remove VLA from xra1403 driver
  gpio: Remove VLA from MAX3191X driver
  gpio: ws16c48: Implement get_multiple callback
  gpio: gpio-mm: Implement get_multiple callback
  gpio: 104-idi-48: Implement get_multiple callback
  gpio: 104-dio-48e: Implement get_multiple callback
  gpio: pcie-idio-24: Implement get_multiple/set_multiple callbacks
  gpio: pci-idio-16: Implement get_multiple callback
  ...
2018-04-05 09:51:41 -07:00
Rodrigo Siqueira
67464a54e5 iio: Replace occurrences of magic number 0 by IIO_CHAN_INFO_RAW
Usually, functions responsible for reading raw data typically relies on
values from iio_chan_info_enum to correctly identify the type of data to
be read. There is a set of a device driver that uses the magic number 0
instead of IIO_CHAN_INFO_RAW. This patch improves the readability by
replaces the magic number 0 for the appropriate IIO_CHAN_INFO_RAW in six
devices driver in the IIO subsystem.

Signed-off-by: Rodrigo Siqueira <rodrigosiqueiramelo@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-03-07 20:14:36 +00:00
William Breathitt Gray
1f8f93683d iio: Change ISA_BUS_API dependency to selection
The ISA_BUS_API Kconfig option enables the compilation of the ISA bus
driver. The ISA bus driver does not perform any hardware interaction,
and is instead just a thin layer of software abstraction to eliminate
boilerplate code common to ISA-style device drivers. Since ISA_BUS_API
has no dependencies and does not jeopardize the integrity of the system
when enabled, drivers should select it when the ISA bus driver
functionality is needed.

Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-02-22 16:13:41 +01:00
Andrew F. Davis
f272f19cb6 iio: dac: mcp4725: Remove unneeded conversions to bool
Found with scripts/coccinelle/misc/boolconv.cocci.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-01-08 16:03:41 +01:00
Benjamin Gaignard
6e93e26193 iio: stm32: Adopt SPDX identifier
Add SPDX identifier in stm32's files in IIO directory

Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-01-08 16:03:41 +01:00
Linus Torvalds
449fcf3ab0 Staging/IIO patches for 4.15-rc1
Here is the "big" staging and IIO driver update for 4.15-rc1.
 
 Lots and lots of little changes, almost all minor code cleanups as the
 Outreachy application process happened during this development cycle.
 Also happened was a lot of IIO driver activity, and the typec USB code
 moving out of staging to drivers/usb (same commits are in the USB tree
 on a persistent branch to not cause merge issues.)
 
 Overall, it's a wash, I think we added a few hundred more lines than
 removed, but really only a few thousand were modified at all.
 
 All of these have been in linux-next for a while.  There might be a
 merge issue with Al's vfs tree in the pi433 driver (take his changes,
 they are always better), and the media tree with some of the odd atomisp
 cleanups (take the media tree's version).
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWgnFrg8cZ3JlZ0Brcm9h
 aC5jb20ACgkQMUfUDdst+ymxbwCgtNlBkqD2JJYpLRKvI/C4w1vzZsEAnA2THRkt
 g3ioPBqmqC/2DSbldr2o
 =/ebw
 -----END PGP SIGNATURE-----

Merge tag 'staging-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging

Pull staging and IIO updates from Greg KH:
 "Here is the "big" staging and IIO driver update for 4.15-rc1.

  Lots and lots of little changes, almost all minor code cleanups as the
  Outreachy application process happened during this development cycle.
  Also happened was a lot of IIO driver activity, and the typec USB code
  moving out of staging to drivers/usb (same commits are in the USB tree
  on a persistent branch to not cause merge issues.)

  Overall, it's a wash, I think we added a few hundred more lines than
  removed, but really only a few thousand were modified at all.

  All of these have been in linux-next for a while. There might be a
  merge issue with Al's vfs tree in the pi433 driver (take his changes,
  they are always better), and the media tree with some of the odd
  atomisp cleanups (take the media tree's version)"

* tag 'staging-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (507 commits)
  staging: lustre: add SPDX identifiers to all lustre files
  staging: greybus: Remove redundant license text
  staging: greybus: add SPDX identifiers to all greybus driver files
  staging: ccree: simplify ioread/iowrite
  staging: ccree: simplify registers access
  staging: ccree: simplify error handling logic
  staging: ccree: remove dead code
  staging: ccree: handle limiting of DMA masks
  staging: ccree: copy IV to DMAable memory
  staging: fbtft: remove redundant initialization of buf
  staging: sm750fb: Fix parameter mistake in poke32
  staging: wilc1000: Fix bssid buffer offset in Txq
  staging: fbtft: fb_ssd1331: fix mirrored display
  staging: android: Fix checkpatch.pl error
  staging: greybus: loopback: convert loopback to use generic async operations
  staging: greybus: operation: add private data with get/set accessors
  staging: greybus: loopback: Fix iteration count on async path
  staging: greybus: loopback: Hold per-connection mutex across operations
  staging: greybus/loopback: use ktime_get() for time intervals
  staging: fsl-dpaa2/eth: Extra headroom in RX buffers
  ...
2017-11-13 20:53:28 -08:00
Greg Kroah-Hartman
b24413180f License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier.  The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
 - file had no licensing information it it.
 - file was a */uapi/* one with no licensing information in it,
 - file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne.  Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed.  Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
 - Files considered eligible had to be source code files.
 - Make and config files were included as candidates if they contained >5
   lines of source
 - File already had some variant of a license header in it (even if <5
   lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

 - when both scanners couldn't find any license traces, file was
   considered to have no license information in it, and the top level
   COPYING file license applied.

   For non */uapi/* files that summary was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0                                              11139

   and resulted in the first patch in this series.

   If that file was a */uapi/* path one, it was "GPL-2.0 WITH
   Linux-syscall-note" otherwise it was "GPL-2.0".  Results of that was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0 WITH Linux-syscall-note                        930

   and resulted in the second patch in this series.

 - if a file had some form of licensing information in it, and was one
   of the */uapi/* ones, it was denoted with the Linux-syscall-note if
   any GPL family license was found in the file or had no licensing in
   it (per prior point).  Results summary:

   SPDX license identifier                            # files
   ---------------------------------------------------|------
   GPL-2.0 WITH Linux-syscall-note                       270
   GPL-2.0+ WITH Linux-syscall-note                      169
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause)    21
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause)    17
   LGPL-2.1+ WITH Linux-syscall-note                      15
   GPL-1.0+ WITH Linux-syscall-note                       14
   ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause)    5
   LGPL-2.0+ WITH Linux-syscall-note                       4
   LGPL-2.1 WITH Linux-syscall-note                        3
   ((GPL-2.0 WITH Linux-syscall-note) OR MIT)              3
   ((GPL-2.0 WITH Linux-syscall-note) AND MIT)             1

   and that resulted in the third patch in this series.

 - when the two scanners agreed on the detected license(s), that became
   the concluded license(s).

 - when there was disagreement between the two scanners (one detected a
   license but the other didn't, or they both detected different
   licenses) a manual inspection of the file occurred.

 - In most cases a manual inspection of the information in the file
   resulted in a clear resolution of the license that should apply (and
   which scanner probably needed to revisit its heuristics).

 - When it was not immediately clear, the license identifier was
   confirmed with lawyers working with the Linux Foundation.

 - If there was any question as to the appropriate license identifier,
   the file was flagged for further research and to be revisited later
   in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.  The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
 - a full scancode scan run, collecting the matched texts, detected
   license ids and scores
 - reviewing anything where there was a license detected (about 500+
   files) to ensure that the applied SPDX license was correct
 - reviewing anything where there was no detection but the patch license
   was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
   SPDX license was correct

This produced a worksheet with 20 files needing minor correction.  This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg.  Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected.  This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.)  Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-02 11:10:55 +01:00
Lukas Wunner
f98677cf31 iio: dac: ti-dac082s085: Read chip spec from device table
The two properties unique to each supported chip, resolution and number
of channels, are currently gleaned from the chip's name.
E.g. dac102s085 is a dual channel 10-bit DAC.
        ^^^
This was deemed unmaintainable by the subsystem maintainer once the
driver is extended to support further chips, hence it was requested
to add an explicit table for chip-specific information and use an
enum to reference into it.

This adds 17 LoC without any immediate gain, so make the change in a
separate commit which can be reverted if we determine in 10 years that
it was unnecessary.

Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-10-21 20:36:45 +01:00
Lukas Wunner
61011264c1 iio: dac: Add Texas Instruments 8/10/12-bit 2/4-channel DAC driver
The DACrrcS085 (rr = 08/10/12, c = 2/4) family of SPI DACs was
inherited by TI when they acquired National Semiconductor in 2011.
This driver was developed for and tested with the DAC082S085 built into
the Revolution Pi by KUNBUS, but should work with any of the other
chips as they share the same programming interface.

There is also a family of I2C DACs with just a single channel called
DACrr1C08x (rr = 08/10/12, x = 1/5).  Their programming interface is
very similar and it should be possible to extend the driver for these
chips with moderate effort.  Alternatively they could be integrated into
ad5446.c.  (The AD5301/AD5311/AD5321 use different power-down modes but
otherwise appear to be comparable.)

Furthermore there is a family of 8-channel DACs called DACrr8S085
(rr = 08/10/12) as well as two 16-bit DACs called DAC161Sxxx
(xxx = 055/997).  These are more complicated devices with support for
daisy-chaining and the ability to power down each channel separately.
They could either be handled by a separate driver or integrated into the
present driver with a larger effort.

Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-10-21 20:35:43 +01:00
Ismail H. Kose
d632a2bd8f iio: dac: ds4422/ds4424 dac driver
This patch provides an iio device driver for DS4422/DS4424 chips that support
two/four channel 7-bit Sink/Source Current DAC.

Signed-off-by: Ismail H. Kose <Ismail.Kose@maximintegrated.com>
Signed-off-by: Ismail H. Kose <ihkose@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-10-09 20:49:39 +01:00
Lukas Wunner
49b3f87496 drivers: misc: ti_dac7512: Remove duplicate driver
The Texas Instruments DAC7512 has the exact same pinout, programming
interface and power-down modes as the Texas Instruments DAC121S101 and
Analog Devices AD5320, which are already supported by the IIO driver
ad5446.c.  Remove the duplicate misc driver.

This requires user space to migrate to the standardized IIO sysfs ABI.
(In other words, it needs to change a filename.)

The IIO driver supports the chip's features more fully, e.g. the ability
to power down the output or choose one of the available powerdown modes.

There is an oddity with the misc driver in that it initializes the SPI
slave to SPI_MODE_0, in contradiction to the datasheet which specifies
that data is latched in on the falling edge, implying that SPI_MODE_1
or SPI_MODE_2 must be used.  Another oddity is that Kconfig and the
MODULE_DESCRIPTION() claim the chip has 16-bit resolution although it
actually has 12-bit.

Datasheets:
http://www.ti.com/lit/ds/symlink/dac7512.pdf
http://www.ti.com/lit/ds/symlink/dac121s101.pdf
http://www.analog.com/media/en/technical-documentation/data-sheets/AD5320.pdf

Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Daniel Mack <daniel@zonque.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-09-13 17:49:57 +01:00
Lukas Wunner
9cad3b9854 iio: dac: ad5446: Add IDs of compatible Texas Instruments chips
The Texas Instruments DAC081S101, DAC101S101 and DAC121S101 have the
exact same pinout, programming interface and power-down modes as the
AD5300, AD5310 and AD5320, respectively, and their datasheets declare
them "a direct replacement" for the Analog Devices chips.  This may
not be immediately obvious to a casual observer, so add them to the
supported modalias strings.

Datasheets:
http://www.ti.com/lit/ds/symlink/dac081s101.pdf
http://www.ti.com/lit/ds/symlink/dac101s101.pdf
http://www.ti.com/lit/ds/symlink/dac121s101.pdf
http://www.analog.com/media/en/technical-documentation/data-sheets/AD5300.pdf
http://www.analog.com/media/en/technical-documentation/data-sheets/AD5310.pdf
http://www.analog.com/media/en/technical-documentation/data-sheets/AD5320.pdf

Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-09-13 17:49:57 +01:00
Jonathan Cameron
ea9e3f3588 iio:dac: drop assignment of iio_info.driver_module
The equivalent of this is now done via macro magic when
the relevant register call is made.  The actual structure
element will shortly go away.

Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
2017-08-22 21:26:54 +01:00